Parkside PHKS 1450 LASER Bruksanvisning

Last Information Update · Tietojen tila · Informationsstatus · Tilstand af

information · Έκδοση των πληροφοριών · Stand der Informationen:

07 / 2008 · Ident.-No.: PHKS 1450 LASER-072008-3

Art. Nr.: 23501

KompernaSS GmbH

Burgstraße 21

D-44867 Bochum

PHKS_1450_Cover_LB3.indd 1 30.07.2008 15:10:24 Uhr

HANDkreissäge

Bedienungs- und Sicherheitshinweise

CIRCULAR SaW

PHKS 1450 LASER

käsiPYÖrÖsAHA

Käyttö- ja turvaohjeet

HANDCirkeLsÅg

Bruksanvisning och säkerhetsanvisningar

HÅNDrUNDsAV

Brugs- og sikkerhedsanvisninger

ΠΡΙΟΝΙ ΧΕΙΡΟΣ

Υποδείξεις χειρισμού και ασφαλείας

CirCULAr sAW

Operation and Safety Notes

PHKS_1450_Cover_LB3.indd 2 30.07.2008 15:10:28 Uhr

Before reading, unfold the page containing the illustrations and familiarise yourself with all functions of the

device.

Käännä ennen lukemista kuvallinen sivu esiin ja tutustu seuraavaksi laitteen kaikkiin toimintoihin.

Vik ut bildsidan och ha den till hands när du läser igenom anvisningarna och gör dig bekant med

apparatens / maskinens funktioner.

Før du læser, vend siden med billeder frem og bliv bekendt med alle apparatets funktioner.

Πριν ξεκινήσετε την ανάγνωση, ανοίξτε τη σελίδα με τις εικόνες και εξοικειωθείτε με όλες τις λειτουργίες της

συσκευής.

Klappen Sie vor dem Lesen die Seite mit den Abbildungen aus und machen Sie sich anschließend mit allen

Funktionen des Gerätes vertraut.

GB / IE / CY Operation and Safety Notes Page 5

FI Käyttö- ja turvaohjeet Sivu 17

SE Bruksanvisning och säkerhetsanvisningar Sidan 29

DK Brugs- og sikkerhedsanvisninger Side 41

GR / CY Υποδείξεις χειρισμού και ασφαλείας Σελίδα 53

DE / AT Bedienungs- und Sicherheitshinweise Seite 67

PHKS_1450_Cover_LB3.indd 3 30.07.2008 15:10:32 Uhr

a

6

11

12

4

9

1

2

3

4

5

6

7

6 a

8

1413

15

22

17

16

21 20 19 18

22

23

24

10

b C

D

e F

13a

13

PHKS_1450_Cover_LB3.indd 4 30.07.2008 15:10:36 Uhr

5 GB/IE/CY

Table of Content

Introduction

Proper use .....................................................................................................................Page 6

Features and equipment ...............................................................................................Page 6

Included items ...............................................................................................................Page 7

Technical information ...................................................................................................Page 7

General safety advice

1. Your working area ....................................................................................................Page 7

2.

Electrical safety ........................................................................................................Page 8

3. Personal safety .........................................................................................................Page 8

4. Careful handling and use of electrical tools ..........................................................Page 9

Safety advice relating speciﬁcally to this device .......................................................Page 9

Preparing for use

Switching on and oﬀ ....................................................................................................Page 13

Setting the cutting angle ..............................................................................................Page 13

Setting the cutting depth ..............................................................................................Page 13

Setting the guide fence ................................................................................................Page 13

Switching the laser on and oﬀ .....................................................................................Page 13

Working with the circular saw .....................................................................................Page 13

Setting the speed ..........................................................................................................Page 13

Connecting the vacuum sawdust extraction device ...................................................Page 14

Changing a saw blade ................................................................................................Page 14

Installing and setting the riving knife ..........................................................................Page 14

Tips and tricks ...............................................................................................................Page 15

Maintenance and cleaning ........................................................................Page 15

Disposal ......................................................................................................................Page 15

Information

Service ...........................................................................................................................Page 15

Warranty .......................................................................................................................Page 15

Declaration of Conformity / Manufacturer .................................................................Page 16

PHKS_1450_Content_LB3.indd 5 30.07.2008 15:08:43 Uhr

6 GB/IE/CY

Introduction

Circular saw PHKS 1450 LASER

Q

Introduction

Please make sure you familiarise your-

self fully with the way the device works

before you use it for the ﬁrst time and

that you understand how to handle electrical pow-

er tools correctly. To help you do this please read

the accompanying operating instructions. Keep

these instructions in a safe place. If you pass the

device on to anyone else, please ensure that you

also pass on all the documentation.

Q

Proper use

For sawing longitudinal, cross and mitre cuts in ﬁrm-

ly supported solid wood, plywood, plastic and

lightweight construction materials. Please note that

the blade pre-installed in the saw as supplied is in-

tended for use with wood only. Any other use or

modiﬁcation to the device shall be considered as

improper use and could give rise to considerable

dangers.

Not suitable for commercial use.

Q

Features and equipment

1

Rotation speed setting wheel

2

Safety lock-out

3

Spindle lock

4

Cutting angle setting clamp

5

Cutting depth setting clamp

6

Automatic blade guard

6 a

Release lever for the automatic blade guard

7

Base plate

8

ON / OFF switch

9

Sawdust removal connector

10

Wing screw for guide fence

11

Guide fence slot

12

Guide fence

13

Laser unit

13 a

Laser outlet aperture

The following pictograms are used in these operating instructions / on the device:

Read instruction manual! Protect electrical devices from moisture!

Observe caution and safety notes!

Risk of loss of life by electric shock from

damaged mains lead or mains plug!

Caution – electric shock!

Danger to life!

Wear hearing protection, dust

protection mask, protective glasses

and protective gloves.

V

~

Volt (AC)

Caution, laser! Do not expose yourself

to laser radiation.

n

0

Design no-load speed Proper procedure and handling.

W

Watts (Eﬀective power) Automatic power delivery system

Safety class II Electronic soft start

Risk of explosion!

Do not dispose of rechargeable batteries

with your household refuse!

Keep children away from

electrical devices!

Dispose packaging and appliance in

an environmentally-friendly way!

PHKS_1450_Content_LB3.indd 6 30.07.2008 15:08:45 Uhr

7 GB/IE/CY

Introduction / General safety advice

14

Laser ON / OFF switch

15

Cutting depth scale

16

Riving knife

17

Auxiliary handle

18

Drive spindle

19

Mounting ﬂange

20

Clamping ﬂange

21

Clamping screw with plain washer

22

Riving knife mounting

23

Mounting screws

24

Adapter for vacuum sawdust removal

Q

Included items

1 Circular saw

1 Guide fence

1 Adapter for vacuum sawdust removal

1 Allen key

2 Batteries, micro AAA 1.5 V (for laser)

1 Operating instructions

Q

Technical information

Nom. power input: 1450 W

Rated voltage: 230 V

~

50 Hz

Mechanical output: 15 Nm max.

No-load speed: n

0

1800 - 5000 min

-1

Saw blade: 210 x 30 x 1.8 x 2.6 mm

Cutting depth at 90°: 0 - 75 mm

Cutting depth at 45°: 0 - 49 mm

Protection class: II /

Noise and vibration data:

Values determined in accordance with EN 60745

The sound pressure level (A-weighted) of the device

is typically 93 dB (A). Uncertainty K=3 dB. The

sound level while working can exceed 104 dB (A).

Wear ear protection!

Evaluated acceleration, typical:

Hand / arm vibration a

h

= 2,309 m / s

2

Uncertainty K = 1,5 m / s

2

WARNING! The vibration level given in

these instructions has been measured in accord-

ance with a standardised measurement procedure

speciﬁed in EN 60745 and can be used to com-

pare devices. Diﬀerent uses of the device give rise

to diﬀerent vibration levels and in many cases they

may exceed the values given in these instructions. It

is easy to underestimate the vibration load if the elec-

trical power tool is used regularly in particular cir-

cumstances.

Note: If you wish to make an accurate assessment

of the vibration loads experienced during a particular

period of working, you should also take into account

the intervening periods of time when the device is

switched oﬀ or is running but is not actually in use.

This can result in a much lower vibration load over

the whole of the period of working.

General safety advice

WARNING!

Read all the safety advice and

instructions! Failure to observe the safety advice

and instructions may result in electric shock, ﬁre

and / or serious injury.

KEEP ALL THE SAFETY ADVICE AND INSTRUCTIONS

IN A SAFE PLACE FOR FUTURE REFERENCE!

1. Your working area

a) Keep your working area clean and

clutter-free. Untidy or poorly lit working ar-

eas can lead to accidents.

b)

Do not work with the device

in potentially explosive en-

vironments in which there

are inflammable liquids, gases or

dusts. Electrical power tools create sparks,

which can ignite dusts or fumes.

c)

Keep children and other

people away while you are

operating the electrical tool.

Distractions can cause you to lose control of

the device.

PHKS_1450_Content_LB3.indd 7 30.07.2008 15:08:45 Uhr

8 GB/IE/CY

General safety advice

2.

Electrical safety

To avoid danger to life from

electric shock:

a) The mains plug on the device must

match the mains socket. The plug must

not be modified in any way. Do not

use an adapter plug with devices fit-

ted with a protective earth. Unmodiﬁed

plugs and matching sockets reduce the risk of

electric shock.

b) Avoid touching earthed surfaces such

as pipes, radiators, ovens and refrig-

erators with any part of your body.

There is an increased risk of electric shock if

your body is earthed.

c)

Keep the device away from

rain or moisture. Water enter-

ing an electrical device

increases the risk of electric shock.

d)

Do not use the mains lead

for any purpose for which it

was not intended, e.g. to

carry the device, to hang up the de-

vice or to pull the mains plug out of

the mains socket. Keep the mains

lead away from heat, oil, sharp edg-

es or moving parts of the device. Dam-

aged or tangled mains leads increase the risk

of electric shock.

e) When working outdoors with an

electrical power tool always use ex-

tension cables that are also ap-

proved for use outdoors. The use of an

extension cable suitable for outdoor use reduc-

es the risk of electric shock.

f) Use a residual current device (RCD)

for protection if operating the electri-

cal power tool in a moist environment

is unavoidable. The use of an RCD reduces

the risk of electric shock.

3. Personal safety

a) Remain alert at all times, watch what

you are doing and always proceed

with caution. Do not use the device if

you are tired or under the influence

of drugs, alcohol or medication.

One moment of carelessness when using the

device can lead to serious injury.

b)

Wear personal protective

equipment and always wear

safety glasses. The wearing of

personal protective equipment such as dust

masks, non-slip safety shoes, safety helmets or

ear protectors, appropriate to the type of elec-

trical power tool used and work undertaken,

reduces the risk of injury.

c) Avoid unintentional operation of the

device. Check that the electrical pow-

er tool is switched off before you

connect it to the mains, pick it up or

carry it. Accidents can happen if you carry

the device with your ﬁnger on the ON / OFF

switch or with the device switched on.

d) Remove any setting tools or spanners

before you switch the device on. A tool

or spanner left attached to a rotating part of a

device can lead to injury.

e) Avoid placing your body in an unnat-

ural position. Keep proper footing and

balance at all times. By doing this you will be

in a better position to control the device in un-

foreseen circumstances.

f) Wear suitable clothing. Do not wear

loose clothing or jewellery. Keep your

hair, clothing and gloves clear of

moving parts. Loose clothing, jewellery or

long hair can become trapped in moving parts.

g) If vacuum dust extraction and collec-

tion devices are fitted do not forget to

check that they are properly connect-

ed and correctly used. The use of these

devices reduces the hazard presented by dust.

PHKS_1450_Content_LB3.indd 8 30.07.2008 15:08:45 Uhr

9 GB/IE/CY

General safety advice

4. Careful handling and use of

electrical tools

a) Do not overload the device. Always

use an electrical power tool that is in-

tended for the task you are undertak-

ing. By using the right electrical power tool for

the job you will work more safely and achieve

a better result.

b) Do not use an electrical power tool if

its switch is defective. An electrical pow-

er tool that can no longer be switched on and

oﬀ is dangerous and must be repaired.

c) Pull the mains plug from the socket

before you make any adjustments to

the device, change accessories or when

the device is put away. This precaution is

intended to prevent you from unintentionally

starting the device.

d) When not in use always ensure that

electrical power tools are kept out of

reach of children. Do not let anyone

use the device if he or she is not famil-

iar with it or has not read the instruc-

tions and advice. Electrical power tools are

dangerous when they are used by inexperienced

people.

e) Look after the device carefully.

Check that moving parts are working

properly and move freely. Check for

any parts that are broken or dam-

aged enough to detrimentally affect

the functioning of the device. Have

damaged parts repaired before you

use the device. Many accidents have their

origins in poorly maintained electrical power

tools.

f) Keep cutting tools clean and sharp.

Carefully maintained cutting tools with sharp

cutting edges are less likely to jam and are

easier to control.

g) Use the electrical power tool, acces-

sories, inserted tools etc. in accord-

ance with these instructions and ad-

vice, and the stipulations drawn up

for this particular type of device. In

doing this, take into account the

working conditions and the task in

hand. The use of electrical power tools for

purposes other than those intended can lead to

dangerous situations.

Safety advice relating

speciﬁcally to this device

J Ensure that the device is always used in accord-

ance with the advice in these operating instruc-

tions and only by persons over 16 years of age.

Note: Do not use grinding discs. Failure to ob-

serve this advice may result in injury or damage.

To avoid danger to life from

electric shock:

J Frequently check the condition of the

device, mains lead and plug.

Do not use the device if these kinds

of parts are damaged. Never open up the device.

A damaged device, mains lead or plug presents a

serious danger to life from electric shock.

Always have any repairs carried out or re-

placement parts ﬁtted at the service centre or

by an electrical equipment repair specialist.

J Devices marked with 230 V can also be oper-

ated at 220 V.

J Do not operate the device if it is damp and do

not use it in a damp environment.

J If you use the device outdoors, always connect

it through a residual current device (RCD) with

a maximum trip current of 30 mA. If using an

extension lead, always use one that is approved

for outdoor use.

Note: Always keep the mains lead away from the

working area of the machine and lead away the

mains lead from the rear.

CAUTION! To avoid the

risk of injury:

a) Keep your hands away from the

area around the saw and clear of the

PHKS_1450_Content_LB3.indd 9 30.07.2008 15:08:46 Uhr

10 GB/IE/CY

General safety advice

saw blade. Hold the auxiliary handle

or the motor housing with your free

hand. If you have both hands on the saw

they cannot be injured by the saw blade.

b) Do not grip the underside of the

workpiece. The blade guard cannot protect

you from the saw blade under the workpiece.

c) Set the cutting depth to match the

thickness of the workpiece. Less than a

full tooth height should be visible below the

workpiece.

d) Never hold the workpiece in your

hand or steady it with your leg

whilst sawing. Keep the workpiece

steady on a stable supporting sur-

face. It is important to see that the workpiece

is ﬁrmly held in place to minimise any danger

of it making contact with your body, jamming of

the saw blade or loss of control.

e) Hold the device by the insulated han-

dle surfaces when you are undertak-

ing work where there is the danger

of the cutting tool striking hidden

electricity cables or the device‘s

mains lead. Contact with a live wire means

that the metal parts of the device may also be-

come live and this can result in an electric shock.

f) When cutting longitudinally always

use a guide fence or a straight edge

guide. This will improve the accuracy of your

cut and reduce the risk of the blade jamming.

g) Always use a saw blade of the correct

size and with the appropriate central

fixing hole bore. Saw blades that do not

correspond with the attachment components

on the saw will not run true and could lead to

loss of control.

h) Never use a damaged or incorrect

saw blade washer or screw. The saw

blade washer and screw have been specially

designed to give your saw optimum performance

and safety in use.

To avoid the device kicking back:

Kickback occurs as a result of incorrect use or mis-

use of the saw. It can be prevented by taking the

appropriate precautions as described below.

a) Hold the saw with both hands and

bring your arms into a position in

which you will be able to withstand

any kickback forces. Always stand to

the side of the saw blade and never

bring your body in line with the saw

blade. When kickback occurs, the circular

saw may jump backwards but the operator

can control the kickback forces by adopting

suitable precautions.

b) If the saw blade jams or sawing

stops for another reason, release the

ON / OFF switch and hold the saw in

the workpiece without moving it un-

til the saw blade comes to a complete

standstill. Never try to remove the

saw from the workpiece or move it

backwards until the saw blade has

stopped moving or cannot cause a

kickback. Find the reason for the saw blade

jamming and take the appropriate action to

rectify it.

c) If you wish to restart a saw that has

been inserted into the workpiece,

centre the saw blade in the saw gap

and check that the saw teeth do not

catch on the workpiece. If the saw blade

jams, it may move itself out of the workpiece or

cause a kickback when the saw is restarted.

d) Support boards whilst cutting to re-

duce the risk of kickback caused by

a jammed saw blade. Large boards may

bend under their own weight. Boards must be

supported on both sides as well as near the

saw gap and at the edges.

e) Do not use blunt or damaged saw

blades. Saw blades with blunt or misaligned

teeth are in eﬀect too wide for the designed saw

gap and this gives rise to increased friction,

jamming and kickback.

f) Make sure that the cutting depth and

angle setting fastenings are tightened

before sawing starts. If these settings

move during sawing, this can lead to the saw

blade jamming and kickback.

g) Be particularly careful when carrying

out a plunge cut in an obscured area,

General safety advice

PHKS_1450_Content_LB3.indd 10 30.07.2008 15:08:46 Uhr

11 GB/IE/CY

e.g. in an existing wall. The plunging

blade could jam in a hidden object and cause

kickback.

Causes of kickback:

a) A kickback is a sudden reaction to a saw blade

becoming hooked, jammed or misaligned. This

causes an out of control circular saw to raise it-

self and move out of the workpiece and towards

the operator.

b) If the sawblade becomes hooked or trapped in

a narrowing saw gap, it is suddenly prevented

from rotating and the force of the motor throws

the device back in the direction of the operator.

c) If the sawblade distorts or becomes misaligned

in the saw cut, the teeth at the rear edge of the

sawblade may hook themselves into the work-

piece surface causing the sawblade to move

out of the saw gap and the circular saw to jump

backwards in the direction of the operator.

Special safety advice for circular saws

and automatic blade guards

a) Before you use the saw, always check

that the automatic blade guard

6

closes properly. Do not use the saw if

the bottom compartment of the blade

guard does not move freely or close

immediately. Never jam or tie the

automatic blade guard in the open

position. The bottom part of automatic blade

guard may become bent if the saw falls on to

the ﬂoor. Open the blade guard with the release

lever and make sure that it moves freely and

does not touch the saw blade or other parts at

all cutting angles and depths.

b) Check that the spring on the automat-

ic blade guard functions properly. If

the automatic blade guard or spring

does not function properly, have the

device serviced before you use it.

Damaged parts, sticky deposits or accumula-

tions of splinters can delay the operation of the

bottom blade guard.

c) Open the automatic blade guard by

hand only for certain cuts such as

plunge or angle cuts. Open the auto-

matic blade guard with the release

lever

6 a

and let it go again as soon as

the saw blade penetrates the work-

piece. The automatic blade guard must be al-

lowed to operate automatically for all saw cuts.

d) Do not put the saw down on a work

bench or the floor without the auto-

matic blade guard covering the saw

blade. If unprotected, a rotating saw blade

moves the saw against the cutting direction and

saws whatever is in its way. Always be aware

that the saw blade takes some time to stop.

Special safety advice for circular saws

and riving knives

a) Use the riving knife matched to the

installed saw blade. The riving knife must

be thicker than the body of the blade but thinner

than the width of the teeth.

b) Adjust the riving knife as described in

the operating instructions. If its thickness,

position or alignment is incorrect, this can lead

to the riving knife not eﬀectively preventing

kickback.

c) Always use the riving knife, except

for plunge cuts. After completing plunge

cutting, put the riving knife back in place. The

riving knife interferes with plunge cuts and can

result in kickback.

d) For the riving knife to work properly,

it must be within the saw gap. The riv-

ing knife is ineﬀective in preventing kickback

for short cuts.

e) Do not operate the saw if the riving

knife is bent out-of-true. Even a slight defect

can cause the blade guard to close too slowly.

General safety advice

PHKS_1450_Content_LB3.indd 11 30.07.2008 15:08:46 Uhr

12 GB/IE/CY

WARNING! Protecting yourself

from laser radiation:

Laser beam

Do not Look into the beam!

Laser cLass 2

J Do not look directly into the laser beam or into

the opening from which it is emitted.

J

WARNING!

Looking at the laser output

aperture

13 a

with optical instruments (e.g.

magnifying glass, magnifying lens, etc.) could

result in eye damage.

J Never direct the laser beam on to reﬂective

surfaces or at people or animals. Even a brief

look into a laser beam can damage your eyes.

J Do not open the laser attachment housing ex-

cept to replace the batteries (2 AAA micro, 1.5 V).

Use a suitable Phillips screwdriver to unscrew

the housing.

J Insert the batteries observing the correct polari-

ty and screw the housing back in place.

C AUTION! The use of operating or adjustment

devices or other methods of working other than

those indicated in this document may lead to

exposure to hazardous radiation.

Working safely:

J If a dangerous situation arises, pull the mains

plug immediately out of the mains socket.

J Never use the device for a purpose for which it

was not intended.

J Always keep the device clean, dry and free of

oil or grease.

J If the saw is used whilst ﬁxed in place on a saw

table then the saw table must have a restart

cut-out.

J Make sure the device is switched on before

placing it against the workpiece.

J Always work away from your body.

J Do not saw materials containing asbestos.

J The course of the cut must have no obstructions

above or below it.

J The saw blade must not project more than

3 mm out of the workpiece.

J When you are sawing, always make sure that

you do not cut through any nails, screws or the

like.

J Do not work with the device in the overhead

position.

J Protect the saw blade from sharp blows or im-

pacts and prevent it from becoming tilted.

J When you switch oﬀ the saw, allow the blade

to slow down naturally - do not assist this proc-

ess in any way.

J Cracked or distorted blades are not to be

used. HSS (High Speed Steel) saw blades are

not to be used.

J Before carrying out any work on the saw, e.g.

setting the base plate etc. always pull the

mains plug out of the mains socket.

J Never remove sawdust or splinters whilst the

saw is running.

J Have a suitable, tested vacuum removal device

attached to the saw when working with woods

or materials that create dusts that may be haz-

ardous to health.

J Always use the safety devices integrated into

the circular saw, e.g. the safety lock-out and

automatic blade guard.

J Ensure that all moving parts of the saw blade

protection system function properly and all the

assemblies and components involved in cover-

ing the saw blade are in perfect working order.

J Do not lock on the ON / OFF switch in hand-

guided operation.

General safety advice

PHKS_1450_Content_LB3.indd 12 30.07.2008 15:08:47 Uhr

13 GB/IE/CY

Preparing for use

Q

Preparing for use

The PHKS 1450 LASER circular saw has Intelligent

Power Control.

This automatic power

delivery system ensures

that for a particular

speed range the power output remains constant when

working on harder and more resistant materials.

Q

Switching on and oﬀ

Switching on:

j Press the safety lock-out

2

to the left or right

and keep it pressed.

j Press the ON / OFF switch

8

. Once the saw

is running you can release the safety lock-out

again.

The circular saw is ﬁtted with an

electronic soft start system. The

motor starts with a delay.

Switching off:

j Release the ON / OFF switch

8

.

Q

Setting the cutting angle

You can set the cutting angle accurately with the

help of the cutting angle scale.

j Release the wing screws of the cutting angle

setting clamp

4

on both sides, set the desired

angle on the scale and retighten the wing

screws.

Q

Setting the cutting depth

Note: If possible we recommend that the cutting

depth is set approximately 3 mm greater than the

material thickness. This should help to ensure you

achieve a clean cut.

j Release the wing screw on the cutting depth

setting clamp

5

, set the required cutting depth

on the scale

15

and retighten the wing screw.

Q

Setting the guide fence

j Release the wing screw

10

of the base plate

7

and insert the guide fence

12

into the slot

11

.

Retighten the wing screw

10

.

Q

Switching the laser on and oﬀ

Switching on:

j Move the laser ON / OFF switch

14

to setting “I”.

Switching off:

j

Move the laser ON / OFF switch

14

to setting “0”.

Note: If the batteries become exhausted you should

replace them with two new ones, type AAA 1.5 V.

Q

Working with the circular saw

1. Switch on the device as described in the section

about “Switching on and oﬀ” and then place it

ﬁrst with the front edge of the base plate

7

against the material.

2. Align the device using the guide fence

12

or

with reference to marked-out line or by using

the laser.

3. Saw with a even pressure whilst holding the

device by the handles with both hands

(see Fig. A).

Q

Setting the speed

j Turn the wheel

1

to the desired speed setting

(arrow marking G)

(1 = lowest speed / 6 = highest speed):

Use the general settings suggested in the following

table (information oﬀered without liability) or adjust

the speed setting on the setting wheel

1

to the

material being cut.

PHKS_1450_Content_LB3.indd 13 30.07.2008 15:08:49 Uhr

14 GB/IE/CY

Preparing for use

Material Speed

setting

Hard- and softwood (solid

wood) cut longitudinally and

transversely

6

Plywood, hard ﬁbre board 6

Chipboard 6

Blockboard, laminated wood 6

Coated and veneered board 6

PVC board 3-5

Acrylic glass panels, Plexiglas 2-4

Aluminium board 4-6

Aluminium proﬁles 4-6

Plasterboard 1-2

Mineral wool board 1-2

Cement-bound chipboard 1-2

The circumferential speeds at minimum and maxi-

mum rotational speeds are approx.:

Setting Rpm Metres/ sec

1 1.800 20

6 5.000 55

Make sure that the cutting speed resulting from the

eﬀects of diﬀerent saw blades, materials and the

force you apply to advance the saw is always less

than the circumferential speed (CS) under no load.

Q

Connecting the vacuum

sawdust extraction device

j Insert the adapter for vacuum sawdust removal

24

into the sawdust removal connector.

j Connect a vacuum device approved for the

extraction of sawdust and splinters.

Q

Changing a saw blade

WARNING!

Press the spindle lock only after

the mains plug has been pulled out of the socket!

1. Then remove the guide fence

12

by releasing

the wing screw

10

.

2. Set the cutting depth (by means of the wing

screw for cutting depth setting clamp

5

) to

the minimum position, 0 mm.

3. Swing back the automatic blade guard

6

and place the device down.

4. Press the spindle lock button (until it engages)

and release the clamping screw

21

using the

Allen key. Now remove the clamping screw

with integral washer head

21

and the clamp-

ing ﬂange

20

(see Fig. D).

5. Detach the saw blade.

6. The installation of a sawblade is done in the re-

verse order.

7. Press the spindle lock button

3

(until it engag-

es) and tighten the clamping screw

21

using

the Allen key.

WARNING!

The arrow on the saw blade

must agree with the arrow showing the direction of

rotation (running direction shown on the device).

j Ensure that the saw blade is suitable for the

saw spindle speed.

Q

Installing and setting the

riving knife

WARNING!

The distance between the riving

knife

16

and the saw blade must not be greater

than 5 mm. If the riving knife has been removed e.g.

for a plunge cut, this distance must be observed

again when the riving knife is reinstalled (see Fig. F).

Removing the riving knife: (see Fig. E)

1. Release the wing screws of the cutting depth

setting clamp

5

and swing the circular saw

up until it meets the stop; this exposes the riving

knife mounting

22

.

2. Screw out the mounting screws

23

and remove

the riving knife

16

.

WARNING!

After completion of the plunge

cut the riving knife

16

must be reinstalled before

the circular saw is used for any other sawing tasks.

PHKS_1450_Content_LB3.indd 14 30.07.2008 15:08:49 Uhr

15 GB/IE/CY

Preparing for use / Maintenance and cleaning / Disposal / Information

Setting the riving knife: (see Fig. F)

Set the distance between the riving knife

16

and

the tips of the saw blade teeth to a maximum of 5

mm, and the distance between the tip of the riving

blade and the lowest point of the saw blade to a

maximum of 5 mm.

The distances to be set are illustrated in Fig. F.

Q

Tips and tricks

j Use the appropriate marking on the base plate

for the desired cutting angle (the marking can

be found behind the wing screw for the guide

fence

10

): Right-angled cut = marking 0°,

45°- cut = marking 45°.

j Breaking out of the cut edges of delicate sur-

faces, e.g. coated chipboard or doors, can be

avoided by applying masking tape in advance

along the cutting line. This has the additional

advantage that masking tape shows up the cut-

ting line better than a smooth surface. An even

more eﬀective way of stopping the cut edges

from being broken out is to clamp a thin piece

of wood along the cutting line, which is then

also sawn through.

Q

Maintenance and cleaning

WARNING!

Always pull the mains plug out

of the socket before doing any work on the device.

j Clean the device after you have ﬁnished using it.

j Use a cloth to clean the outside of the device -

never use petrol, solvents or cleaners.

Q

Disposal

The packaging is wholly composed of

environmentally-friendly materials that

can be disposed of at a local recycling

centre.

Do not dispose of electrical

power tools with the household

rubbish!

In accordance with European Directive 2002 / 96 / EC

(covering waste electrical and electronic equipment)

and its transposition into national legislation, worn

out electrical power tools must be collected separate-

ly and taken for environmentally compatible recycling.

Contact your local refuse disposal authority for

more details of how to dispose of your worn out

electrical devices.

Do not dispose of rechargeable

batteries with your household

refuse!

Disposal of batteries

Batteries must be recycled in accordance with

Directive 91 / 157 / EEC and must not be disposed

of with household refuse. Battery users are obliged

by law to take all rechargeable and single-use bat-

teries to a collection point operated by a public

authority or a retailer.

Q

Information

Q

Service

J

WARNING!

Have your device

repaired at the service centre or by

qualified specialist personnel using

original manufacturer parts only. This

will ensure that your device remains safe to use.

J

WARNING!

If the plug or lead

needs to be replaced, always have

the replacement carried out by the

manufacturer or its service centre. This

will ensure that your device remains safe to use.

Q

Warranty

This appliance is guaranteed for 3 years

from the date of purchase. It has been care-

fully produced and meti-culously checked

before delivery. Please keep your receipt

as proof of purchase. Contact your service

centre by telephone in case of questions

pertaining to the warranty. Your goods can

PHKS_1450_Content_LB3.indd 15 30.07.2008 15:08:49 Uhr

16 GB/IE/CY

Information

be transmitted free of cost only in this man-

ner. This warranty applies only to the initial

purchaser and is non-transferable.

The warranty covers only material or manufactur-

ing faults, not normal wear or damage to fragile

parts such as switches or rechargeable batteries.

The appliance is intended solely for private, not

commercial, use.

If this product has been subjected to improper or in-

appropriate handling, abuse, or interventions not

carried out by one of our authorised sales and

service outlets, the warranty will be considered void.

This warranty does not aﬀect your statutory rights.

GB

DES Ltd

Units 14-15

Bilston Industrial Estate

Oxford Street

Bilston (Great Britain)

WV14 7EG

Tel.: 0870 / 787-6177

Fax: 0870 / 787-6168

e-mail: support.uk@kompernass.com

IE

Kompernass Service Ireland

c/o Irish Connection

41 Harbour View

Howth, Co. Dublin (Ireland)

Tel 087-99 62 077

Fax: 18398056

e-mail: support.ie@kompernass.com

Q

Declaration of Conformity /

Manufacturer

We, Kompernaß GmbH, Burgstr. 21,

D-44867 Bochum, Germany, declare that this

product complies with the following EU directives:

Machinery Directive

98 / 37 / EC

EU Low Voltage Directive

2006 / 95 / EC

EN60745-1

EN60745-2-5

Electromagnetic Compatibility

2004 / 108 / EC

EN55014-1

EN55014-2

EN61000-3-2

EN61000-3-3

EN61000-6-1

EN61000-6-3

EN60825-1

Type / Device description:

Circular saw PHKS 1450 LASER

Bochum, 31.07.2008

Hans Kompernaß

- Managing Director -

We reserve the right to make technical modiﬁcations in the course

of further development.

PHKS_1450_Content_LB3.indd 16 30.07.2008 15:08:50 Uhr

17 FI

Sisällysluettelo

Aluksi

Määräystenmukainen käyttö .......................................................................................Sivu 18

Varusteet ........................................................................................................................Sivu 18

Toimitus sisältää ............................................................................................................Sivu 19

Tekniset tiedot ...............................................................................................................Sivu 19

Yleiset turvallisuusohjeet

1. Työpaikka ..................................................................................................................Sivu 19

2.

Sähköturvallisuus ......................................................................................................Sivu 20

3. Henkilöiden turvallisuus ...........................................................................................Sivu 20

4. Tarkkaavainen käsittely ja käyttö sähkölaitteilla ...................................................Sivu 20

Laitetta koskevat turvallisuusohjeet ..............................................................................Sivu 21

Käyttöönotto

Kytkentä ja poiskytkentä ..............................................................................................Sivu 24

Sahauskulman säätö ....................................................................................................Sivu 24

Sahaussyvyyden säätö ................................................................................................Sivu 24

Rinnakkaisohjaimen säätö ...........................................................................................Sivu 24

Laserin kytkentä/poiskytkentä .....................................................................................Sivu 24

Käsipyörösähän käsittely .............................................................................................Sivu 25

Käyntinopeuden säätö .................................................................................................Sivu 25

Lastuimurin liitäntä ........................................................................................................Sivu 25

Sahanterän vaihto ........................................................................................................Sivu 25

Halkaisukiila purkaminen ja säätö ..............................................................................Sivu 26

Vinkit ja konstit ..............................................................................................................Sivu 26

Huolto ja puhdistus ..........................................................................................Sivu 26

Hävittäminen ........................................................................................................Sivu 26

Tietoja

Huolto ............................................................................................................................Sivu 26

Takuu ..............................................................................................................................Sivu 27

Vaatimustenmukaisuusvakuutus / Valmistaja ...............................................................Sivu 27

PHKS_1450_Content_LB3.indd 17 30.07.2008 15:08:50 Uhr

18 FI

Käsipyörösaha PHKS 1450 LASER

Q

Aluksi

Tutustu ennen käyttöönottoa laitteeseen,

sen käyttöohjeisiin ja sähkölaitteita kos-

keviin yleisiin turvallisuusohjeisiin. Lue

tämä käyttöopas huolella. Säilytä käyttöopas huo-

lellisesti. Saatat myöhemmin tarvita sen tietoja. Jos

luovut laitteesta, anna uudelle omistajalle myös

kaikki laitteen asiakirjat.

Q

Määräystenmukainen käyttö

Tukevalla alustalla täyspuun, lastulevyjen sekä ke-

vytrakenneaineksien sahaukseen. Ota huomioon,

että laitteeseen kiinnitetty sahanterä on tarkoitettu

vain puun sahaukseen. Laitteen käyttö muuhun tar-

koitukseen tai muutoksien teko siihen katsomtaan

määräystenvastaiseksi ja on vaarallista.

Ei kaupalliseen käyttöön.

Q

Varusteet

1

Käyntinopeuden säädin

2

Käynnistyksen esto

3

Karalukitus

4

Sahauskulman valinta

5

Sahaussyvyyden valinta

6

Teränsuoja

6 a

Suojakotelon takaisinvetovipu

7

Peruslaatta

8

Virtakytkin KYTKIN / KATKAISIN

9

Lastunpoisto

10

Rinnakkaisohjaimen siipiruuvi

11

Rinnakkaisohjaimen paikka

12

Rinnakkaisohjain

13

Laserlisäke

13 a

Laserlähtö

14

KYTKIN / KATKAISIN laserlisäke

15

Sahaussyvyysasteikko

16

Halkaisukiila

17

Lisäkahva

18

Käyttökara

19

Kiinnityslaippa

Aluksi

Tässä käyttöohjeessa / laitteessa käytetään seuraavia kuvakkeita:

Lue käyttöohje! Suojaa sähkölaitetta kosteudelta!

Huomioi varoitus- ja turvaohjeet!

Viallisen verkkojohdon tai pistokkeen

käyttöön liittyvän sähköiskun aiheutta-

ma hengenvaara!

Varo sähköiskua! Hengenvaara!

Pidä ja kuulonsuojainta, hengitys- /

pölysuojanaamaria, suojalaseja ja

suojakäsineitä.

V

~

Voltti (Vaihtojännite)

Huomio, Laser! Älä asetu alttiiksi

lasersäteelle.

n

0

Mittaus-tyhjäkäyntikierrosluku Näin käyttäydyt oikein!

W

Watti (Vaikutusteho) Automaattinen voimansyöttö

Suojausluokka II Elektroninen pehmeä käynnistys

Räjähdysvaara!

Älä hävitä akkuja tavallisen

kotitalousjätteen mukana!

Pidä lapset loitolla sähkölaitteesta!

Hävitä pakkaus ja laite

ympäristöystävällisesti!

PHKS_1450_Content_LB3.indd 18 30.07.2008 15:08:52 Uhr

19 FI

Aluksi / Yleiset turvallisuusohjeet

20

Kiristyslaippa

21

Kiristysruuvi ja aluslevy

22

Halkaisukiilan kiinnitys

23

Kiinnitysruuvit

24

Pölyimuriadapteri

Q

Toimitus sisältää

1 Käsipyörösaha

1 Rinnakkaisvaste

1 Pölyimurin adapteri

1 Sisäkuusiokoloavain

2 Paristot Micro AAA 1,5 V (laseriin)

1 Käyttöohje

Q

Tekniset tiedot

Nimellisteho: 1450 W

Nimellisjännite: 230 V

~

50 Hz

Lähtöteho: 15 Nm max.

Tyhjäkäyntikiertoluku: n

0

1800 - 5000 min

-1

Sahanterä: 210 x 30 x 1,8 x 2,6 mm

Sahaussyvyys 90°:ssa: 0 - 75 mm

Sahaussyvyys 45°:ssa: 0 - 49 mm

Suojaluokka: II /

Melu- ja tärinätiedot:

Mittausarvot määritetty normin EN 60745 mukaan.

Laitteen A-painotettu äänenpainetaso on tyypillisesti

93 dB (A). Epävarmuus K=3 dB. Melutaso saattaa

työn aikana ylittää 104 dB (A).

Käytä kuulosuojaimia!

Arvioitu kiihtyvyys, tyypillisesti:

Käteen ja käsivarteen

kohdistuva värinä a

h

= 2,309 m / s

2

Epävarmuus K = 1,5 m / s

2

VAROLTUS!

Näissä ohjeissa ilmoitettu

värähtelytaso on määritetty normissa EN 60745

standardoidulla mittausmenetelmällä ja sitä voidaan

käyttää laitevertailussa.

Värähtelytaso muuttuu säh-

kötyökalun käytön mukaan ja se saattaa monesti

ylittää tässä ohjeessa mainitun arvon. Värähtelyra-

situsta saatetaan aliarvioida, jos sähkötyökalua

säännöllisesti käytetään tällä tavalla.

Huomio: Liikekuormituksen arvioimiseksi tietyn

työajan kestäessä on huomioitava myös ajat, jolloin

laite on sammutettuna, tai ajat, jolloin laite on käyn-

nissä, mutta ei työkäytössä. Tämä saattaa vähentää

merkittävästi liikerasitusta kokonaistyöskentelyajan

kestäessä.

Yleiset turvallisuusohjeet

VAROLTUS!

Lue kaikki turva- ja muut ohjeet!

Turva- ja muiden ohjeiden laiminlyönti voi aiheuttaa

sähköiskun, tulipalon ja / tai vakavia loukkaantumisia.

SÄILYTÄ KAIKKI TURVA- JA MUUT OHJEET

TULEVAA TARVETTA VARTEN!

1. Työpaikka

a) Pidä työpaikka puhtaana ja siivottu-

na. Epäjärjestys ja huono valaistus voivat

johtaa tapaturmiin.

b)

Älä käytä laitetta räjähdys-

vaarallisessa ympäristössä,

jossa säilytetään helposti

syttyviä nesteitä, kaasuja tai jossa

kehittyy pölyä. Sähkötyökalut kehittävät

kipinöintiä, joka voi sytyttää pölyn tai höyryn.

c)

Lapsien ja asiattomien hen-

kilöiden läsnäolo työpaikal-

la laitteen ollessa

käynnissä ei ole sallittua. Voit helposti

menettää kontrollin laitteeseen.

PHKS_1450_Content_LB3.indd 19 30.07.2008 15:08:52 Uhr

20 FI

2.

Sähköturvallisuus

Vältä sähköiskun aiheuttamaa

hengenvaaraa:

a) Laitteen pistokkeen pitää sopia pis-

torasiaan. Pistoketta ei saa muuttaa

millään tavalla. Älä käytä adapteria

yhdessä suojamaadoitettujen laittei-

den kanssa. Alkuperäinen pistoke ja sopivat

pistorasia vähentävät sähköiskuvaaraa.

b) Vältä kosketusta maadoitettuihin

pintoihin, kuten putkiin, lämpöpatte-

reihin, liesiin sekä jääkaappeihin.

Vaarana on saada sähköisku, jos kehosi on

maadoitettu.

c)

Älä pidä laitetta sateessa

tai muussa kosteudessa.

Veden pääsy laitteeseen lisää

sähköiskuvaaraa.

d)

Älä kanna laitetta riiputta-

malla sitä kaapelista ja vedä

kaapeli irti

pistorasiasta pitämällä kiinni pistok-

keesta. Älä jätä kaapelia kuumaan

paikkaan, älä päästä siihen öljyä,

varo teräviä reunoja sekä laitteen

pyöriviä osia. Vialliset tai kietoutuneet

kaapelit lisäävät riskiä saada sähköisku.

e) Jos työskentelet ulkotiloissa, käytä

silloin jatkokaapelia, jonka käyttö

on sallittu myös ulkotilaan. Ulkotilaan

soveltuva kaapeli vähentää riskiä saada

sähköisku.

f) Jos sähkötyökalua joudutaan käyt-

tämään kosteassa ympäristössä, on

käytettävä vikavirtakytkintä. Vikavir-

takytkimen käyttö pienentää sähköiskun vaaraa.

3. Henkilöiden turvallisuus

a) Ole aina tarkkaavainen, tarkista aina,

mitä teet ja toimi järkevästi sähkö-

laitteilla työskennellessäsi. Älä käytä

laitetta, jos olet väsynyt, käyttänyt

huumeita, alkoholia tai lääkkeitä.

Epätarkkaavaisuus laitetta käytettäessä voi

aiheuttaa vaikeita loukkaantumisia.

b)

Käytä henkilökohtaisia tur-

vavarusteita ja suojalaseja

aina. Henkilökohtaisten turvavarus-

teiden käyttö, kuten pölynaamari, turvakengät,

kypärä tai kuulosuoja, vähentävät loukkaantu-

misriskiä.

c) Varo käynnistämästä laitetta vahin-

gossa. Varmista, että sähkötyökalu

on kytketty pois päältä, ennen kuin

liität sen pistorasiaan, nostat sen tai

kannat sitä. Tapaturmat ovat mahdollisia,

jos sormesi on laitetta kantaessasi virtakytkimel-

lä tai laite on kytketty päälle.

d) Poista kaikki työkalut ja ruuviavaimet

paikalta ennen kuin kytket laitteen.

Pyörivässä laiteosassa oleva työkalu tai avain

voi johtaa tapaturmaan.

e) Vältä työskentelemästä epätavalli-

sessa asennossa. Asetu tukevaan asentoon

ja pysyttele koko ajan tasapainossa. Pystyt silloin

hallitsemaan laitteen erityisesti yllättävissä

tilanteissa.

f) Käytä sopivaa vaatetusta. Älä käytä

löysiä vaatteita äläkä pidä koruja.

Hiukset, vaatteet ja käsineet on

pidettävä etäällä liikkuvista osista.

Löysät vaatteet, korut ja avonaiset hiukset voivat

jäädä kiinni liikkuviin osiin.

g) Jos laitteeseen asennetaan pölynimu-

ri- ja lastunkeruulaite, varmistu sitä

ennen, että osat on liitetty ja niitä

käytetään oikein. Näiden laitteiden liittä-

minen vähentää pölystä aiheutuvia vaaroja.

4. Tarkkaavainen käsittely ja

käyttö sähkölaitteilla

a) Älä ylikuormita laitetta. Käytä työs-

sä siihen tarkoitettua sähkölaitetta.

Sopivalla työkalulla on helpompi ja turvallisem-

pi työskennellä.

b) Älä käytä sähkölaitteita, jos kytkin

on viallinen. Sähkölaite, jonka kytkin ei

toimi, on vaarallinen ja se täytyy korjata.

Yleiset turvallisuusohjeet

PHKS_1450_Content_LB3.indd 20 30.07.2008 15:08:53 Uhr

Sidan laddas ...

Parkside PHKS 1450 LASER Bruksanvisning

Parkside PHKS 1450 LASER Bruksanvisning

på andra språk

Relaterade papper

Andra dokument