Sentiotec Auxiliary evaporator R Användarmanual

Evaporator

RB 2,5 kW

1-027-762 / CP-25-STP-B

Version 01/21 Ident no M100-000-238

INSTRUCTIONS FOR INSTALLATION AND USE

English

EN

DE

FR

CS

SV

FI

Table of Contents

1. About this instruction manual 4

2. Important information for your safety 5

2.1. Intended use 5

2.2. Safety information for the installer 6

2.3. Safety information for the user 7

3. Product description 9

3.1. Scope of delivery 9

3.2. Accessories 9

3.3. Product functions 9

4. Installation and connection 10

4.1. Installation location 10

4.2. Safety distances 10

4.3. Installation on the cabin wall 10

4.4. Installation on the Concept R sauna heater 13

4.5. Connection diagram 15

4.6. Electrical connection 16

5. Starting up 18

5.1. Using the ceramic bowl 18

5.2. Heatingupforthersttime 18

6. Operation 19

6.1. Finnish sauna mode 19

6.2. Combi mode 19

EN

7. Maintenance 22

7.1. Cleaning the evaporator tank 22

7.2. Cleaning the ceramic bowl 22

7.3. Descaling the evaporator tank 22

8. Troubleshooting 23

9. Disposal 24

10. Technical data 25

Instructions for installation and use p. 4/26

1. About this instruction manual

Carefully read these instructions for installation and use, and keep them near

the sauna. This ensures you can refer to information about safety and operation

at any time.

Symbols used for warnings

In these installation and operating instructions, warning symbols are displayed

next to activities that are hazardous. Warning symbols must be observed at all

times. This prevents damage to property and injuries, which in the worst case

may be fatal.

The warning symbols contain keywords that mean the following:

DANGER!

Serious or fatal injury will occur if this warning symbol is not observed.

WARNING!

Serious or fatal injury can occur if this warning symbol is not observed.

CAUTION!

Minor injuries can occur if this warning symbol is not observed.

ATTENTION!

This keyword warns that damage to property can occur.

Other symbols

This symbol indicates tips and useful information.

Read the operating instructions

Caution: Hot steam

These installation and operating instructions can also be found in the

downloads section of our website: www.sentiotec.com/downloads.

EN

Instructions for installation and use p. 5/26

2. Important information for your safety

The evaporator RB is constructed in accordance with recognised

safety rules and regulations. Nevertheless, hazards can occur during

use. You should therefore adhere to the following safety information

andthespecicwarningsintheindividualsections.

2.1. Intended use

The evaporator RB may only be used for increasing the humidity

within the sauna cabin and only in combination with a sauna control

with evaporator function and sauna heater.

Any use falling outside this limitation constitutes improper use.

Improper use can result in damage to the product, severe injuries

or death.

Instructions for installation and use p. 6/26

2.2. Safety information for the installer

●Installing and connecting the auxiliary evaporator may only be

performed when the power supply is disconnected.

●Installationmayonlybeperformedbyaqualiedelectricianor

similarlyqualiedperson.

●Anall-poledisconnectingdevicewithfullcut-omustbetted

on-site in accordance with overvoltage category III.

●Always use silicone cables that are heat-resistant up to 150 °C

to connect the auxiliary evaporator.

●The roof and walls of the sauna cabin are manufactured from

low-resin, untreated or thermally treated wood, e.g. Nordic spruce,

hemlock,pineorr,orfromlaminatedwoodenmaterials.Iflami-

nated wooden materials are used, make sure that the adhesive

used in them does not produce formaldehyde. If other materials

apart from wood are used in the sauna cabin, these materials

must be heat and corrosion-resistant and must not have any

negativeeectonthehealthofthesaunausers.

●When installing the auxiliary evaporator R, observe the minimum

safety distances (see 4.2. Safety distances on page 10).

●Observe all the local regulations applicable to the installation.

●For your own safety, consult your supplier in the event of prob-

lemsthatarenotexplainedinsucientdetailintheinstallation

instructions.

EN

Instructions for installation and use p. 7/26

2.3. Safety information for the user

●The device must not be used by children under 8 years old.

●The device may only be used by children over 8 years old, by

persons with limited psychological, sensory or mental capabili-

ties or by persons with lack of experience/knowledge under the

following conditions:

– When they are supervised.

– When they have been shown how to use the device safely

and are aware of the hazards that could occur.

●Children must not play with the device.

●Children under 14 years old may only clean the device if they

are supervised.

● Forhealthreasons,donotusethesaunawhenundertheinu-

ence of alcohol, medication or drugs.

●Heat up the auxiliary evaporator for half an hour BEFORE using

thesaunaforthersttime.DoNOTremaininthesaunacabin

during this period. Thereafter, ventilate the sauna cabin thoroughly

(see 5.2. Heating up for the rst time on page 18).

Instructions for installation and use p. 8/26

●Before the sauna control unit is switched on, make sure that no

ammableobjectshavebeenplacedonthesaunaheateroron

the auxiliary evaporator.

●Never touch the auxiliary evaporator while it is in operation. The

surface of the auxiliary evaporator becomes very hot.

●Avoid direct contact with the steam emitted during operation. The

steam emitted is very hot and there is a risk of scalding.

●Do not put herbs, essences or fragrances directly into the evapo-

rator tank, but only into the ceramic bowl over the evaporator.

●NEVERpourwaterintothehotevaporatortank.Checkandll

the evaporator tank each time before starting combi mode. If

theoverheatingprotectionhasswitchedotheheatingofthe

evaporator or if your sauna control unit reports a lack of water,

allow the evaporator to cool down BEFORE you pour water into

the evaporator tank. The device must be disconnected from the

mainswhilebeinglledorcleaned.

●For your own safety, consult your supplier in the event of prob-

lemsthatarenotdescribedinsucientdetailintheoperating

instructions.

EN

Instructions for installation and use p. 9/26

3. Product description

3.1. Scope of delivery

●Auxiliary evaporator with mounting rail

●Instructions for installation and use

●Ceramic bowl for herbs and fragrances

3.2. Accessories

Accessories Article number

Automaticlling CP-RC-AF

Bracket set for railing CP-RM-HSR-4S

Wooden railing evaporator NUT CP-RM-N-4S

Wooden railing evaporator LINDEN CP-RM-L-4S

3.3. Product functions

The evaporator RB is a device for upgrading a sauna with a Finnish sauna

heater. The additional installation of the evaporator makes the following operat-

ing modes possible:

●Finnish sauna mode: usually 80 to 100 °C; approx. 10 % rel. humidity

●Combi mode (only in combination with a combi control): approx. 40 to 65 °C,

35% to 70% humidity. The maximum permissible relative humidity decreases

with increasing temperature.

If you wish, you can put fragrances or dried herbs in the ceramic bowl over

the evaporator in combi mode. The rising steam releases essential oils from

theherbsandallowsfragrancestollthesaunacabin.

Installation instructions, only for experts p. 10/26

4. Installation and connection

Observe the following points when installing and connecting the auxiliary evapo-

rator:

●Theelectricalconnectionmayonlybeperformedbyaqualiedelectricianor

similarlyqualiedperson.

● Anall-poledisconnectingdevicewithfullcut-omustbettedon-siteinac-

cordance with overvoltage category III.

●The auxiliary evaporator R is intended for installation on the sauna wall.

●Observe the minimum distances specified in 4.2 during installation.

4.1. Installation location

Install the evaporator at a suitable location on the cabin wall or on your Concept

R combi sauna heater, and observe the minimum safety distances when doing so.

4.2. Safety distances

ObservetheminimumsafetydistancesspeciedinFig. 1 (page 12).

4.3. Installation on the cabin wall

Observe Fig. 1, Fig. 2, Fig. 3 and Fig. 4 (page 12, 13).

1. Attach the mounting rail 1 to the wall so it is level with the supplied wood

screws 2 . Observe the minimum distances for the auxiliary evaporator

shown in Fig. 1.

2. Mount the evaporator 3 on the mounting rail starting at the top. Make sure

thattheevaporatorisushagainstthewall.

3. Secure the evaporator 3 using the supplied screws 4 on the mounting rail 1 .

WARNING!

Risk of electric shock

●The auxiliary evaporator must only be installed and connected when

the power supply is disconnected.

EN

Installation instructions, only for experts p. 11/26

Fig.1 Safety distances for 2.5 kW evaporator RB

Dimensions in mm

Fig.2 Mounting rail for 2.5 kW evaporator RB

210210

440

420

2

min. 1000

min. 50450 220

min. 50

Installation instructions, only for experts p. 12/26

Fig.3 Position of mounting rail

Dimensions in mm

Fig.4 Securing the 2.5 kW evaporator RB (mounting rail)

1

3

4

1

63

5 5

EN

Installation instructions, only for experts p. 13/26

4.4. Installation on the Concept R sauna heater

Your can upgrade your Finnish Concept R sauna heater to a combi heater with

the auxiliary evaporator. However, you need to check that your sauna control is

suitable for combi-mode.

Observe the safety distances Fig. 1 (page 12) and Fig. 5, Fig. 6 Fig. 7

(page 14, 15).

1. Loosen the screws 1 on the side of the Concept R sauna heater 2 that

you wish to use.

2. Attach the mounting rail 3 to the Concept R sauna heater as in Fig. 6 with

the screws 1 . Observe the minimum distances in your heater's operating

instructions when selecting the sauna heater's installation location.

3. Mount the evaporator 4 on the mounting rail 3 starting at the top. Make

surethattheevaporatorisushagainstthewall.

4. Secure the evaporator 4 using the supplied screws 5 on the mounting rail 3 .

1

2

Fig.5 Unscrew the screws on the Concept R sauna heater

Installation instructions, only for experts p. 14/26

Fig.6 Attaching the mounting rail to the Concept R sauna heater

3

1

Fig.7 Securing the evaporator RB

4

5

3

L1 L2 N

L3 U

V

N

Wr

r

w

400 V~

3x16 A

U

2,5 kW

N

EN

Installation instructions, only for experts p. 15/26

4.5. Connection diagram

Fig.8 Connection diagram for the 2.5 kW auxiliary evaporator

2

3

4

1 Sauna control unit

2 Temperature sensor with excess temperature controller

3 2.5 kW Auxiliary evaporator

4 9 kW or 10.5 kW Heating system

5 Power supply

1

5

Fig.9 Wiring diagrams – heating system

U1

N

To the

sauna

control unit

12

1 Excess temperature fuse

2 Lack of water

Installation instructions, only for experts p. 16/26

4.6. Electrical connection

1. Unscrew the screws 2 and 3 with a screwdriver.

2. Remove the cover plate 1.

3. Guide the connection cable for the evaporator through the feed-through 5.

4. Connect the connectors of this connection cable to the PE – N – U1 – Wm

terminals, to the connector block 4 and to the applicable sauna control unit

terminals. Observe the installation instructions for the sauna control unit

when doing so.

5. Reattach the cover panel 1 to the auxiliary evaporator R.

1

2

3

Fig.10 Removing the cover panel

EN

Installation instructions, only for experts p. 17/26

4 Connector block for the evaporator

5 Feed-through for the connection cable

5

4

Fig.11 Auxiliary evaporator R connection terminals

Instructions for use for the user p. 18/26

5. Starting up

5.1. Using the ceramic bowl

●Place the ceramic bowl on the evaporator tank as shown in the illustra-

tion on the right.

5.2. Heating up for the rst time

CAUTION!

Formation of smoke and odours when heating up for the rst time

Working materials from the manufacturing process will be present on the

new heating elements. These evaporate when the auxiliary evaporator

isheatedupforthersttime.Thisproducessmokeandanunpleasant

odour. Breathing in the fumes or smoke can be harmful to your health.

Perform the following steps when operating the auxiliary evaporator for

the rst time or if the heating elements for the auxiliary evaporator

have been replaced . This will prevent your health being impaired due to

thefumesandsmokeproducedwhenheatingupforthersttime.

1. Heatingtheevaporatorforthersttime

a. Select a low temperature and high humid-

ity on the sauna control unit.

b. Heat the evaporator WITHOUT water.

Do NOT remain in the sauna cabin

during this period.

►After about 15 minutes, the excess

temperatureprotectionswitchesothe

evaporator.

c. Allow the evaporator to cool

(for approx. half an hour).

d. Repeat step 1. b.

e. Ventilate the sauna cabin thoroughly after

heating up.

EN

Instructions for use for the user p. 19/26

f. If no smoke or odour is produced the next time the sauna heater is

heated up, rinse the cooled evaporator with tap water. Thereafter, you

can start to use the sauna.

If smoke or an odour arises again, leave the sauna cabin immediately,

and repeat the initial heating up process followed by ventilation.

6. Operation

A sauna control unit is used to operate the auxiliary evaporator R. For informa-

tion on how to operate the sauna control unit, read the operating instructions for

the device used.

6.1. Finnish sauna mode

In Finnish sauna mode, only your sauna heater's heating system is in operation.

Dry heat is produced. The temperature in the cabin is high (80 to 100 °C). The

humidity level is low and does not exceed 10%. The temperature in the sauna

cabin is controlled by your sauna control unit.

At the end of the sauna session, you can pour water over the stones. Pour water

over the stones using a sauna ladle. The water evaporates and the humidity in

the sauna cabin is increased.

Observe the instruction manual for your sauna heater.

6.2. Combi mode

In combi mode, the heating system of the sauna heater and the auxiliary evapo-

rator are in operation. The temperature in the sauna cabin is lower than in Finn-

ish sauna mode (approx. 40 to 65 °C), instead of which the relative humidity is

considerably higher at 35% to approximately 70%. The maximum permissible

relative humidity decreases with increasing temperature. The temperature and

the humidity in the sauna cabin are controlled by your sauna control unit.

Theevaporatortankmustbelledmanually.Ifthewaterintheevaporatortank

hasbeenusedup,anoverheatingprotectionfunctionautomaticallyturnsothe

heating of the evaporator. The lack of water is reported to the sauna control unit

and displayed there, e.g. by an audible warning tone and the message “FILL”.

Instructions for use for the user p. 20/26

Filling the evaporator

TheAutoRellSet(CP-RC-AF)allowsforaxedwaterconnection,

makingautomaticllingoftheevaporatortankpossible.

ATTENTION!

Damage to the evaporator

Sea water, hard water, chlorinated water, herbs, essences or fragrances can

damage the sauna heater.

● Onlylltheevaporatortankwithtapwater.

●Do not put herbs, essences or fragrances directly into the evaporator tank,

but only into the ceramic bowl over the evaporator.

●Descale the evaporator regularly (see 7.3. on page 22).

CAUTION!

Risk of scalding

If you pour water into the hot evaporator tank, hot steam is created.

●NEVER pour water into the hot evaporator tank.

● Checkandlltheevaporatortankeachtimebeforestartingcombi

mode.

●Iftheoverheatingprotectionhasswitchedotheheatingofthe

evaporator or if your sauna control unit reports a lack of water, al-

low the evaporator to cool down BEFORE you pour water into the

evaporator tank.

CAUTION!

Risk of scalding

If the evaporator tank is too full, boiling water will spray out of the evapo-

rator tank.

● Onlylltheevaporatortankuptothemaximummark.

1. Remove the ceramic bowl 1 and the steam funnel 2.

2. Place a receptacle (at least 5 litres) under the ball valve at the bottom of

the evaporator.

3. Turntheballvalvetotheleft,untiltheremainingwaterowsout.

4. When the evaporator tank 3 is empty, close the ball valve.

Sidan laddas ...

Sentiotec Auxiliary evaporator R Användarmanual

Sentiotec Auxiliary evaporator R Användarmanual

på andra språk

Relaterade papper

Andra dokument