EXHAUSTO DTV Version 2 Bruksanvisningar

EXHAUSTO A/S

Odensevej 76

DK-5550 Langeskov

Tel. +45 65 66 12 34

Fax +45 65 66 11 10

[email protected]

www.exhausto.dk

DTV 3006656-2023-09-27.fm

DTV Version 2

-TGK

DTV 3006656-2023-09-27.fm

2/56

1. GB - Product information

1.1 Construction and design...................................................................................................................5

2. GB - Fitting

2.1 Transport safety fitting DTV315, DTV400 and DTV450...................................................................6

2.2 TGK roof duct.....................................................................................................................................6

2.3 Installing a fan onto a TGK roof duct...............................................................................................8

2.4 Installing a fan onto a roof base using an FPT base plate.............................................................8

3. GB - Wiring

3.1 Fan without EC control......................................................................................................................9

3.1.1 DTV160-4-1 & DTV200-4-1 .......................................................................................................9

3.2 Fan with EC control .........................................................................................................................10

3.2.1 DTV250-4-1EC2, DTV315-4-1EC2, DTV400-4-1EC2 & DTV450-4-1EC2 ..............................10

3.2.3 Troubleshooting DV-EC controls..............................................................................................12

4. GB - Service and cleaning

4.1 Cleaning............................................................................................................................................13

4.2 Environmental declaration..............................................................................................................14

1. DK - Produktinformation

1.1 Konstruktion.....................................................................................................................................15

2. DK - Montage

2.1 Transportsikring DTV315, DTV400 og DTV450 .............................................................................16

2.2 Taggennemføring TGK....................................................................................................................16

2.3 Montage på taggennemføring TGK................................................................................................18

2.4 Montage på tagsokkel via fodplade FPT........................................................................................18

3. DK - El-tilslutning

3.1 Ventilatorer uden EC-styring ..........................................................................................................19

3.2.1 DTV160-4-1 & DTV200-4-1 .....................................................................................................19

3.2 Ventilatorer med EC-styring ...........................................................................................................20

3.2.2 DTV250-4-1EC2, DTV315-4-1EC2, DTV400-4-1EC2 & DTV450-4-1EC2 ..............................20

3.2.1 Fejlfinding for DV-EC-styring....................................................................................................22

4. DK - Service og rengøring

4.1 Rengøring.........................................................................................................................................23

3.2 Miljødeklaration................................................................................................................................24

DTV 3006656-2023-09-27.fm

3/56

1. DE - Produktinformation

1.1 Konstruktion.....................................................................................................................................25

2. DE - Montage

2.1 Transportsicherung DTV315, DTV400 und DTV450......................................................................26

2.2 Dachdurchführung TGK..................................................................................................................26

2.3 Montage auf der Dachdurchführung TGK .....................................................................................28

2.4 Montage auf Dachsockel über Fußplatte FPT...............................................................................28

3. DE - Elektrischer Anschluss

3.1 Ventilatoren ohne EC-Automatik....................................................................................................29

3.2.1 DTV160-4-1 & DTV200-4-1 .....................................................................................................29

3.2 Ventilatoren mit EC-Automatik.......................................................................................................30

3.2.2 DTV250-4-1EC2, DTV315-4-1EC2, DTV400-4-1EC2 & DTV450-4-1EC2 ..............................30

3.2.1 Fehlersuche bei DV-EC-Automatik ..........................................................................................32

4. DE - Wartung und Reinigung

4.1 Reinigung .........................................................................................................................................33

3.2 Umweltdeklaration...........................................................................................................................34

1. NO - Produktinformasjon

1.1 Konstruksjon....................................................................................................................................35

2. NO - Montering

2.1 Transportsikring DTV315, DTV400 og DTV450 .............................................................................36

2.2 Takgjennomføring TGK...................................................................................................................36

2.3 Montering på takgjennomføring TGK ............................................................................................38

2.4 Montering på taksokkel via fotplate FPT .......................................................................................38

3. NO - Elektrisk tilkobling

3.1 Vifter uten EC-styring......................................................................................................................39

3.1.1 DTV160-4-1 & DTV200-4-1 .....................................................................................................39

3.2 Vifter med EC-styring ......................................................................................................................40

3.2.1 DTV250-4-1EC2, DTV315-4-1EC2, DTV400-4-1EC2 & DTV450-4-1EC2 ..............................40

3.2.1 Feilsøking for DV-EC-styring....................................................................................................42

4. NO - Service og rengjøring

3.1 Rengjøring........................................................................................................................................43

3.2 Miljødeklarasjon...............................................................................................................................44

DTV 3006656-2023-09-27.fm

4/56

1. SE - Produktinformation

1.1 Konstruktion.....................................................................................................................................45

2. SE - Montering

2.1 Transportsäkring DTV315, DTV400 och DTV450 ..........................................................................46

2.2 Takgenomföring TGK ......................................................................................................................46

2.3 Montering på takgenomföring TGK................................................................................................48

2.4 Montering på taksockel via fotstöd FPT........................................................................................48

3. SE - Elanslutning

3.1 Fläktar utan EC-styrning .................................................................................................................49

3.1.1 DTV160-4-1 & DTV200-4-1 .....................................................................................................49

3.2 Fläktar med EC-styrning .................................................................................................................50

3.2.1 DTV250-4-1EC2, DTV315-4-1EC2, DTV400-4-1EC2 & DTV450-4-1EC2 ..............................50

3.2.1 Felsökning för DV-EC-styrning ................................................................................................52

4. SE - Service och rengöring

3.1 Rengöring.........................................................................................................................................53

3.2 Miljödeklaration................................................................................................................................54

DTV 3006656-2023-09-27.fm GB - Product information

5/56

1.GB - Product information

EXHAUSTO DTV roof fans are used in air supply and extraction systems.

The ventilator is not to be used to transport solid particles, nor in areas

where there is a risk of explosive gases.

The ventilator must not be started with the Top section open.

Description EXHAUSTO DTV vertical discharge roof fans are available in the following single-phase

motor models (EC types have built-in EC control:

• DTV160-4-1

• DTV200-4-1

• DTV250-4-1EC2

• DTV315-4-1EC2

• DTV400-4-1EC2

• DTV450-4-1EC2

The roof fan is made of corrosion-resistant aluminium. To protect fingers and avoid birds

getting trapped in the fan box, it is fitted with a rustproof safety net.

Main components

Size and weight

1.1 Construction and design

Pos. Part

a Top section

b Bottom section

c Motor

d Centrifugal impeller

e Centrifugal impeller inlet

f Safety fittings

g Net

h Handle

i Connecting cable

j Rubber ring seal between the fan and duct/base plate

k Vibration dampers ensure vibration-free operation

l EC regulator

m Safety screws (yellow)

n Top section cover

Q

5'

L

O

j, k and m, see section 2.3

DTV 160 200 250 315 400 450

Weight, kg 11 17 28 37 52 60

DTV 3006656-2023-09-27.fm GB - Fitting

6/56

2.GB - Fitting

Before installation

Remove the transport safety fitting by the centrifugal impeller (can be done without

having to open the fan) and check that the impeller turns freely.

Construction EXHAUSTO standard TGK roof ducts are made of

galvanised plate casing, with 50 mm mineral wool for

insulation/sound absorption and fibreglass and has an

internal galvanised perforated plate.

The roof duct has an inner cable conduit, through which

the isolation switch cabling and the cabling can be pulled

all the way through.

The roof duct is delivered with anti-backdraught shutters

AOR.

Installing the

isolation switch

Fit the isolation switch (not supplied by EXHAUSTO) on the TGK roof duct directly onto

the seal. The fan's connecting cable is fed in from the bottom through the threaded cable

entry.

Duct system and

extraction system

The roof duct can be connected to any EUROVENT-

standard duct system.

2.1 Transport safety fitting DTV315, DTV400 and DTV450

RD13628-01

2.2 TGK roof duct

RD12887-01

RD12889-02

DTV 3006656-2023-09-27.fm GB - Fitting

7/56

Installing TGK roof ducts

Step Action

1 Make a hole in the roof, approx. 30 mm larger than the roof duct.

2 Loosen the overlying tile/roofing and push it up to make room for the cover.

PERFORM or lead cover Zinc cover

NB:

applies only to

PERFORM

It is a good idea to bend the edge of the

flashing (at the bottom and if appropriate, the

visible part of the sides) to ensure greater

strength/better form stability and a nicer finish.

See the pictures above.

3 Fit the roof duct carefully into the roof so the

cover is flush with the top of the tiles.

Fit the roof duct carefully into the roof so the

cover is flush with the roofing material.

4 Fit the support bars to the roof duct, so that

the roof duct will be lifted approx. 5 mm when

the support bars have been attached to the

roofing beams. This ensures that all the

weight is taken by the support bars.

Fit the support bars to the roof duct, so that

the roof duct will be lifted approx. 1 mm when

the support bars have been attached to the

roofing beams. This ensures that all the

weight is taken by the support bars.

5 Roll out the cover material and knock it gently

into shape with a rubber hammer or sandbag.

6If water travels from copper or bitumen onto

PERFORM, FlashSeal must be applied to the

PERFORM surface.

If you do not follow the instructions, the war-

ranty becomes void!

7 Replace the overlying tile/roofing over the cover.

DTV 3006656-2023-09-27.fm GB - Fitting

8/56

The fan can be mounted directly onto the EXHAUSTO standard TGK roof duct

NB The air being extracted can contain water vapour and cause condensation, so the

roof base must be insulated.

2.3 Installing a fan onto a TGK roof duct

3-01

Step Action

1 Tighten securely the provided four vibration dampers (k) in the threaded

holes in the roof duct.

2 Place the rubber ring (j) between the duct and the centrifugal impeller inlet.

3 Secure the roof fan onto the vibration dampers with the nuts.

4 Tighten the two yellow safety screws (m) in the roof duct via the free holes in

the bottom section. The screws ensure the DTV remains attached to the roof

duct in all situations.

RD12884-01

2.4 Installing a fan onto a roof base using an FPT base plate

RD12124-01

Step Action

1 Fasten the base plate onto the roof base.

2 Seal the base plate and roof base joint using a joint sealing compound.

3 Tighten securely the four vibration dampers provided (k) in the threaded

holes in the base plate.

4 Place the rubber ring (j) between the duct and the centrifugal impeller inlet.

5 Secure the roof fan onto the vibration dampers with the nuts.

6 Tighten the two yellow safety screws (m) in the base plate via the free holes

in the bottom section. The screws ensure the DTV remains attached to the

base plate in all situations.

RD12885-01

DTV 3006656-2023-09-27.fm GB - Wiring

9/56

3.GB - Wiring

General

The wiring must only be done by a qualified electrician.

The fan and motor specifications are listed on the type-plates.

Max. fuse rating = 13 Amp.

Max. short circuit current is 10 kA

At start-up and during the initial adjustment of the fan, it is important to control the

direction of rotation of the motor and to check the motor current does not exceed the

manufacturer’s recommended operating current for the motor (to avoid damaging the

motor).

Isolation switch EXHAUSTO A/S would like to draw attention to the fact that, in

accordance with the EU's Machine Directive (appendix 1) all fan

systems shall include a isolation switch.

The isolation switch must ...

• be lockable or positioned in plain sight in the immediate vicinity of the fan

• be able to disconnect all poles from the supply voltage

— contact distance of at least 3 mm in each pole

• Set up as isolation switch in accordance with standard IEC 60947-1 or

IEC 60947-3.

The isolation switch is not supplied by EXHAUSTO.

Lightning

conductor

Any lightning conductor connected to the fan must be in accordance with applicable

regulations and legislation.

3.1.1 DTV160-4-1 & DTV200-4-1

Wiring

All single-phase fans are voltage regulated.

The motor is fitted with a thermal cut-out. The thermal-cut out is factory installed, wired

in series to the motor's power circuit.

If the fuse is a ...it must have the characteristic

melting fuse gG or gM.

control fuse B or C, and comply with IEC 90947-2. -

3.1 Fan without EC control

Wiring — cable from the motor

Single-phase motor with built-in thermal

cut-out

DTV160-4-1, DTV200-4-1

Brown = L

Blue = N

Yellow/Green =

DTV 3006656-2023-09-27.fm GB - Wiring

10/56

General Fans marked EC have a built-in EC control.

Cables The wiring for control signal inputs must be completely insulated from the supply wirings.

ESD

The electrician must be ESD protected when

• detaching the cover on the EC control

• working with the EC control

3.2.1 DTV250-4-1EC2, DTV315-4-1EC2, DTV400-4-1EC2 & DTV450-4-1EC2

Cable type Cables for control signals must be with twisted pair conductors. As a minimum, the cable

type must be CAT5e Ethernet cable.

Diagram

3.2 Fan with EC control

DTV 3006656-2023-09-27.fm GB - Wiring

11/56

Key to diagram

Leakage current The EC control produces a leakage current when running. The leakage current must be

earthed, as there is a risk of the motor becoming live.

A leakage current of up to 150 mA can be generated.

To comply with EN50178, the fan must be suitably earthed.

Earth leak circuit

breakers

If current earth leak circuit breakers are fitted in the installation, they must be of

a type that meets the following requirements:

• PFI type B breaker according to EN 61008, that breaks the circuit when a

vagrant current with DC content (pulsating DC) or smooth vagrant current

is registered.

• The circuit breakers must be marked with the following symbols:

Terminal Signal description Comments

1RS485 + (A)

2RS485 - (B)

3 0 V DC (chassis)

4 10 V DC EFC1P/EFC1P2 panel 5

5 0-10 V DC EFC1P/EFC1P2 panel 4

6 0 V DC (chassis) EFC1P/EFC1P2 panel 3

7

8 Start/stop EFC1P/EFC1P2 panel 2

9

10 0 V DC (chassis)

11 Run NC

12 Run C

13 Run NO

14 Alarm NC

15 Alarm C EFC1P/EFC1P2 panel B

16 Alarm NO EFC1P/EFC1P2 panel A

DTV 3006656-2023-09-27.fm GB - Wiring

12/56

3.2.2 Troubleshooting DV-EC controls

DV-EC-control

LED indicator • The DV-EC control is equipped with a two-coloured green and red LED indicator

of the different operating modes.

• The LED is located on the underside of the control unit next to the cable entry for

the main voltage connection.

Troubleshooting

chart

• Steady green when main voltage is connected.

• Flashes green when Modbus communication is active.

• Steady red for at least one critical alarm.

• Flashes red for at least one non-critical alarm.

• LED error indicator:

• 1 flash = Supply problem

• 3 flashes = Internal DV problem

• 5 flashes = motor problem

Accessory As an accessory you can buy a hand-held terminal for operation and alarm info.

DTV 3006656-2023-09-27.fm GB - Service and cleaning

13/56

4.GB - Service and cleaning

EXHAUSTO DTV roof fan motors have special ball bearings that are sealed, lubricated

and maintenance-free. Any replacement of these bearings should be carried out by

technicians from EXHAUSTO SERVICE.

The fan and duct system should be cleaned as necessary, depending on dirt levels, in

the following manner:

4.1 Cleaning

Step Action

1 Shut down the fan using the isolation switch

2 Loosen the screws on the front of the fan and swing the top section

up by the handle. The safety fitting will ensure the top section stays

up as you clean.

3 Brush the centrifugal impeller.

Wash the impeller with soapy water if needed. Be very careful to

avoid water getting into the duct system or into the motor.

4 The roof duct and duct system:

Remove the impeller-insert (e) and if necessary the anti-backdraught

AOR. The roof duct and the duct system can now be cleaned down

inside and around the opened fan.

NB: Cleaning of the duct system must be done carefully, in such a

fashion as to avoid any dirt or dust getting into the fan's operating

parts.

DTV 3006656-2023-09-27.fm GB - Service and cleaning

14/56

Product

description

EXHAUSTO DTV is a an easily serviced radial fan with backward curved blades. The

fan impeller is directly mounted on the motor shaft, thus reducing losses and wear and

resulting in lower repair costs.

Service and cleaning is done by opening the hinged cover. This provides access to all

parts in contact with the air.

The motor and any motor controls are mounted outside the air flow. The fan is CE

approved and EMC tested in accordance with the applicable directives.

Materials used The fan housing and the fan impellers are made of recyclable pressure-cast aluminium.

The visible parts of the fan housing are painted with water-based paint.

The motor consists of aluminium, steel and copper, and in some cases a plastic cooling

jacket. The packaging consists of corrugated cardboard.

Materials in %

4.2 Environmental declaration

DTV160 DTV200 DTV250EC2 DTV315EC2 DTV400EC2 DTV450EC2

Aluminium 75% 79% 72% 76% 75% 72%

Fe 17% 15% 16% 15% 19% 22%

Copper 4% 3% 2% 1% 2% 2%

PCB;

electronic

components

1% 1% 7% 5% 2% 2%

Plastic,

cellular rubber

1% 1% 1% 1% 1% 1%

Other 2% 1% 2% 2% 1% 1%

DTV 3006656-2023-09-27.fm DK - Produktinformation

15/56

1.DK - Produktinformation

EXHAUSTO tagventilator DTV anvendest i indblæsnings- og udsugningsanlæg.

Ventilatoren må ikke anvendes til transport af faste partikler, eller hvor

der er risiko for eksplosive gasarter.

Ventilatoren må ikke startes med åben toppart.

Beskrivelse EXHAUSTO tagventilator DTV har vertikalt afkast og fås i følgende 1-fasede

motorvarianter (EC er betegnelsen for EC motorer med indbygget EC-styring):

• DTV160-4-1

• DTV200-4-1

• DTV250-4-1EC2

• DTV315-4-1EC2

• DTV400-4-1EC2

• DTV450-4-1EC2

Tagventilatoren er af korrosionsbestandigt aluminium. Der er monteret rustfrit net som

finger- og fuglebeskyttelse.

Hovedkomponenter

Størrelse og vægt

1.1 Konstruktion

Pos. Del

a Toppart

b Bundpart

c Motor

d Centrifugalhjul

e Centrifugalindsats

f Sikringsbeslag

g Net

h Håndtag

i Tilslutningskabel

j Gummiring. Tætner mellem ventilator og taggennemføring/fodplade.

k Svingningsdæmpere. Sikrer vibrationsfri drift.

l EC-regulator

m Sikkerhedsskruer (gule)

n Topdæksel

Q

5'

L

O

j, k og m, se afsnit 2.3

DTV 160 200 250 315 400 450

Vægt - kg 11 17 28 37 52 60

DTV 3006656-2023-09-27.fm DK - Montage

16/56

2.DK - Montage

Inden montage

Fjern transportsikringen ved centrifugalhjulet (kan gøres uden at åbne ventilatoren) og

kontroller at hjulet kan løbe uhindret rundt.

Beskrivelse EXHAUSTO standard taggennemføring TGK er

opbygget af et galvaniseret pladesvøb, 50 mm

mineraluld for isolering/ lyddæmpning, glasvæv

og indvendigt en galvaniseret perforeret plade.

Taggennemføringen er forsynet med en

indvendig kabelkanal, hvor installationskablet til

forsyningsadskilleren trækkes igennem.

Taggennemføringen leveres med

overtryksspjæld AOR.

Monter

forsyningsadskiller

Monter forsyningsadskilleren (ikke EXHAUSTO leverance) på taggennemføringen TGK

direkte imod pakningen. Ventilatorens tilslutningskabel føres ind i forsyningsadskilleren

nedefra gennem kabelforskruning.

Kanalsystem og

udsugnings-

amatur

Taggennemføringen kan i bunden tilsluttes

ethvert kanalsystem med standardmål i

henhold til EUROVENT (nippelmål).

2.1 Transportsikring DTV315, DTV400 og DTV450

RD13628-01

2.2 Taggennemføring TGK

RD12887-01

RD12889-02

DTV 3006656-2023-09-27.fm DK - Montage

17/56

Sådan monteres taggennemføringen TGK

Trin Handling

1 Der laves et hul i taget, ca. 30 mm større end taggennemføringen.

2 Overliggende tagsten/-plade løsnes og forskydes opad a.h.t. inddækningen.

PERFORM-inddækning Zinkinddækning

BEMÆRK

- gælder kun

PERFORM

Kanten af inddækningen (nederst, samt evt.

den synlige del af siderne) kan med fordel

ombukkes. Herved opnås større styrke (bedre

formstabilitet og en pænere finish (se

ovenstående fotos.).

3 Taggennemføringen placeres forsigtigt i taget,

således at inddækningen ligger plant med

toppen af tagpladerne.

Taggennemføringen placeres forsigtigt i taget,

således at inddækningen ligger plant med

tagmaterialet.

4 Bærejernene fastgøres til taggennemføringen,

således at den løftes ca. 5 mm, når

bærejernene efterfølgende fastgøres til

tagspærene. Herved sikres at hele vægten

ligger på bærejernene.

Bærejernene fastgøres til taggennemføringen,

således at den løftes ca. 1 mm, når

bærejernene efterfølgende fastgøres til

tagspærene. Herved sikres at hele vægten

ligger på bærejernene.

5 Inddækningsmaterialet rulles ud og bankes

forsigtigt i form med en gummihammer eller

sandpose.

6 Sker der afvanding fra kobber eller bitumen

(tagpap) til PERFORM, skal PERFORM’s

overflade påføres FlashSeal. Følges

anvisningerne ikke, bortfalder garantien!

7 Overliggende tagsten/-plade lægges på plads over inddækningen.

DTV 3006656-2023-09-27.fm DK - Montage

18/56

Ventilatoren kan monteres direkte på EXHAUSTO standard taggennemføring TGK.

Bemærk Ved fugtig udsugningsluft kan der forekomme kondensvand, og tagsoklen skal

derfor altid isoleres.

2.3 Montage på taggennemføring TGK

3-01

Trin Handling

1 Spænd de 4 medleverede svingningsdæmpere (k) fast i gevindhullerne i

taggennemføringen.

2 Læg gummiringen (j) udvendigt om kanten på centrifugalindsatsen.

3 Fastspænd tagventilatoren på svingningsdæmperne med møtrikkerne.

4 Spænd de to gule sikkerhedsskruer (m) i taggennemføringen gennem

frihuller i bundparten. Skruerne sikrer, at DTV’en fastholdes på

taggennemføringen i alle situationer.

2.4 Montage på tagsokkel via fodplade FPT

RD12124-01

Trin Handling

1 Fastgør fodpladen til tagsoklen.

2 Forsegl samlingen mellem fodplade og tagsokkel med fugemasse.

3 Spænd de 4 medleverede svingningsdæmpere (k) fast i gevindhullerne i

fodpladen.

4 Læg gummiringen (j) udvendigt om kanten på centrifugalindsatsen.

5 Fastspænd tagventilatoren på svingningsdæmperne med møtrikkerne.

6 Spænd de to gule sikkerhedsskruer (m) i fodpladen gennem frihuller i

bundparten. Skruerne sikrer, at DTV’en fastholdes på fodpladen i alle situationer.

DTV 3006656-2023-09-27.fm DK - El-tilslutning

19/56

3.DK - El-tilslutning

Generelt

El-installationen skal foretages af autoriseret el-installatør.

Ventilator- og motorspecifikationer fremgår af de monterede typeskilte.

Max. forsikring = 13 Amp.

Max. kortslutningsstrøm er 10 kA

Ved opstart og indregulering af ventilationsanlægget er det vigtigt at kontrollere

motorens omløbsretning, og at strømforbruget ikke overstiger mærkestrømmen på

typeskiltet, da det vil medføre overbelastning af motoren.

Forsyningsadskiller EXHAUSTO A/S gør opmærksom på, at der i henhold til

Maskindirektivet (bilag 1) skal opsættes en forsyningsadskiller i den

faste installation af ventilatoren.

Forsyningsadskilleren skal...

• være aflåselig, eller placeres synligt i nærheden af ventilatoren.

• kunne afbryde alle poler fra forsyningsspændingen

- kontaktafstand min. 3 mm i hver pol.

• udføres som forsyningsadskiller i hht. IEC 60947-1 eller IEC 60947-3

Forsyningsadskilleren er ikke en del af EXHAUSTO’s leverance.

Lynafledning... ...skal ske i henhold til gældende love og bestemmelser.

3.1.1 DTV160-4-1 & DTV200-4-1

El-tilslutning

Alle 1-fasede ventilatorer er spændingsregulerbare.

Motoren er forsynet med termosikring. Termosikringen er fra fabrikken koblet i serie

med motorens strømkreds.

Hvis forsikringen er en ...skal den være med karakteristik

smeltesikring gG eller gM.

automatsikring B eller C, og opfylde IEC 90947-2.

3.1 Ventilatorer uden EC-styring

El-tilslutning - kabel fra motor

1-fasemotor med indbygget termosikring

DTV160-4-1, DTV200-4-1

Brun= L

Blå= Nreg.

Gul/Grøn=

DTV 3006656-2023-09-27.fm DK - El-tilslutning

20/56

Generelt Alle ventilatorer med typebetegnelsen "EC" er regulerbare via den indbyggede EC-

styring.

Kabler De ledninger, der skal tilsluttes styresignal-indgangene, skal i hele deres længde have

en forstærket isolering i forhold til forsyningsnettet.

ESD Elektrikeren skal være ESD-beskyttet:

• når låget på EC-styringen demonteres

• under arbejdet med EC-styringen

3.2.1 DTV250-4-1EC, DTV315-4-1EC & DTV400-4-1EC2

Kabeltype Kabler til styresignaler skal være med parsnoede ledere. Kabeltypen skal minimum

være CAT5e Ethernet kabel.

Diagram

3.2 Ventilatorer med EC-styring

Sidan laddas ...

EXHAUSTO DTV Version 2 Bruksanvisningar

EXHAUSTO DTV Version 2 Bruksanvisningar

på andra språk

Relaterade papper

Andra dokument