Yamaha RXV3000 Användarmanual

varumärke: Yamaha

Modell: RXV3000

Kategori: AV-mottagare

Typ: Användarmanual

Denna manual är också lämplig för

STANDBY

/ON

NATURAL SOUND AV RECEIVER RX–V3000

INPUT MODE

INPUT

VOLUME

SILENT

PHONES

SPEAKERS

PROCESSOR

DIRECT

BASS

EXTENSION

BASS TREBLE REC OUT/ZONE 2

VIDEO AUX

VCR 1

SAT

CABLE

D-TV/LD

DVD

SOURCE

/REMOTE

MD/TAPE

CD-R

TUNER

PHONO

VCR 2/DVR

EFFECT

6CH

INPUT

TUNING

MODE

MEMORY

S VIDEO VIDEO L R OPTICALAUDIO

MAN'L/AUTO FM AUTO/NAN'L MONO

FM/AM

PRESET

/TUNING

DSP

PROGRAM

EDIT

VIDEO AUX

RX-V3000

Natural Sound AV Receiver

Ampli-Tuner Audio-Video

OWNER'S MANUAL

MODE D'EMPLOI

UCA

CAUTION

• Explanation of Graphical Symbols

The lightning flash with arrowhead

symbol, within an equilateral triangle, is

intended to alert you to the presence of

uninsulated “dangerous voltage” within the

product’s enclosure that may be of

sufficient magnitude to constitute a risk of

electric shock to persons.

The exclamation point within an

equilateral triangle is intended to alert you

to the presence of important operating and

maintenance (servicing) instructions in the

literature accompanying the appliance.

1 Read Instructions – All the safety and operating instructions

should be read before the unit is operated.

2 Retain Instructions – The safety and operating instructions

should be retained for future reference.

3 Heed Warnings – All warnings on the unit and in the operating

instructions should be adhered to.

4 Follow Instructions – All operating and other instructions

should be followed.

5 Water and Moisture – The unit should not be used near water –

for example, near a bathtub, washbowl, kitchen sink, laundry

tub, in a wet basement, or near a swimming pool, etc.

6 Carts and Stands – The unit should be used only with a cart or

stand that is recommended by the

manufacturer.

6A A unit and cart combination should be moved

with care. Quick stops, excessive force, and

uneven surfaces may cause the unit and cart

combination to overturn.

7 Wall or Ceiling Mounting – The unit should be mounted to a

wall or ceiling only as recommended by the manufacturer.

WARNING

TO REDUCE THE RISK OF FIRE OR

ELECTRIC SHOCK, DO NOT EXPOSE THIS

UNIT TO RAIN OR MOISTURE.

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE

COVER (OR BACK). NO USER-SERVICEABLE

PARTS INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION

IMPORTANT SAFETY INSTRUCTIONS

8 Ventilation – The unit should be situated so that its location or

position does not interfere with its proper ventilation. For

example, the unit should not be situated on a bed, sofa, rug, or

similar surface, that may block the ventilation openings; or

placed in a built-in installation, such as a bookcase or cabinet

that may impede the flow of air through the ventilation

openings.

9 Heat – The unit should be situated away from heat sources such

as radiators, stoves, or other appliances that produce heat.

10 Power Sources – The unit should be connected to a power

supply only of the type described in the operating instructions

or as marked on the unit.

11 Power-Cord Protection – Power-supply cords should be routed

so that they are not likely to be walked on or pinched by items

placed upon or against them, paying particular attention to

cords at plugs, convenience receptacles, and the point where

they exit from the unit.

12 Cleaning – The unit should be cleaned only as recommended by

the manufacturer.

13 Nonuse Periods – The power cord of the unit should be

unplugged from the outlet when left unused for a long period of

time.

14 Object and Liquid Entry – Care should be taken so that objects

do not fall into and liquids are not spilled into the inside of the

unit.

15 Damage Requiring Service – The unit should be serviced by

qualified service personnel when:

A. The power-supply cord or the plug has been

damaged; or

B. Objects have fallen, or liquid has been spilled into the unit;

C. The unit has been exposed to rain; or

D. The unit does not appear to operate normally or exhibits a

marked change in performance; or

E. The unit has been dropped, or the cabinet damaged.

16 Servicing – The user should not attempt to service the unit

beyond those means described in the operating instructions. All

other servicing should be referred to qualified service

personnel.

17 Power Lines – An outdoor antenna should be located away from

power lines.

18 Grounding or Polarization – Precautions should be taken so that

the grounding or polarization is not defeated.

19 For US customers only:

Outdoor Antenna Grounding – If an outside antenna is

connected to this unit, be sure the antenna system is grounded

so as to provide some protection against voltage surges and

built-up static charges. Article 810 of the National Electrical

Code, ANSI/NFPA 70, provides information with regard to

proper grounding of the mast and supporting structure,

grounding of the lead-in wire to an antenna discharge unit, size

of grounding conductors, location of antenna discharge unit,

connection to grounding electrodes, and requirements for the

grounding electrode.

CAUTION

FCC INFORMATION (for US customers only)

We Want You Listening For A Lifetime

YAMAHA and the Electronic Industries Association’s Consumer

Electronics Group want you to get the most out of your equipment

by playing it at a safe level. One that lets the sound come through

loud and clear without annoying blaring or distortion – and, most

importantly, without affecting your sensitive hearing.

Since hearing damage from loud sounds is often

undetectable until it is too late, YAMAHA and the

Electronic Industries Association’s Consumer

Electronics Group recommend you to avoid prolonged

exposure from excessive volume levels.

Compliance with FCC regulations does not guarantee that

interference will not occur in all installations. If this product

is found to be the source of interference, which can be

determined by turning the unit “OFF” and “ON”, please try

to eliminate the problem by using one of the following

measures:

Relocate either this product or the device that is being

affected by the interference.

Utilize power outlets that are on different branch (circuit

breaker or fuse) circuits or install AC line filter/s.

In the case of radio or TV interference, relocate/reorient the

antenna. If the antenna lead-in is 300 ohm ribbon lead,

change the lead-in to coaxial type cable.

If these corrective measures do not produce satisfactory

results, please contact the local retailer authorized to

distribute this type of product. If you can not locate the

appropriate retailer, please contact Yamaha Electronics

Corp., U.S.A. 6660 Orangethorpe Ave, Buena Park, CA

90620.

The above statements apply ONLY to those products

distributed by Yamaha Corporation of America or its

subsidiaries.

1. IMPORTANT NOTICE : DO NOT MODIFY THIS

UNIT!

This product, when installed as indicated in the instructions

contained in this manual, meets FCC requirements.

Modifications not expressly approved by Yamaha may void

your authority, granted by the FCC, to use the product.

2. IMPORTANT : When connecting this product to

accessories and/or another product use only high quality

shielded cables. Cable/s supplied with this product MUST

be used. Follow all installation instructions. Failure to

follow instructions could void your FCC authorization to use

this product in the USA.

3. NOTE : This product has been tested and found to comply

with the requirements listed in FCC Regulations, Part 15 for

Class “B” digital devices. Compliance with these

requirements provides a reasonable level of assurance that

your use of this product in a residential environment will not

result in harmful interference with other electronic devices.

This equipment generates/uses radio frequencies and, if not

installed and used according to the instructions found in the

users manual, may cause interference harmful to the

operation of other electronic devices.

Note to CATV system installer:

This reminder is provided to call the CATV system installer’s

attention to Article 820-40 of the NEC that provides guidelines

for proper grounding and, in particular, specifies that the cable

ground shall be connected to the grounding system of the

building, as close to the point of cable entry as practical.

EXAMPLE OF ANTENNA GROUNDING

MAST

GROUND

CLAMP

ANTENNA

LEAD IN

WIRE

ANTENNA

DISCHARGE UNIT

(NEC SECTION 810–20)

GROUNDING CONDUCTORS

(NEC SECTION 810–21)

GROUND CLAMPS

POWER SERVICE GROUNDING

ELECTRODE SYSTEM

(NEC ART 250. PART H)

ELECTRIC

SERVICE

EQUIPMENT

NEC

– NATIONAL ELECTRICAL CODE

CAUTION

CAUTION: READ THIS BEFORE OPERATING THIS UNIT.

1 To assure the finest performance, please read this manual

carefully. Keep it in a safe place for future reference.

2 Install this unit in a well ventilated, cool, dry, clean place with

at least 30 cm on the top, 20 cm on the right and left, and 10

cm at the back of this unit for ventilation space — away from

direct sunlight, heat sources, vibration, dust, moisture, and/or

cold.

3 Locate this unit away from other electrical appliances, motors,

or transformers to avoid humming sounds. To prevent fire or

electrical shock, do not place this unit where it may get

exposed to rain, water, and/or any type of liquid.

4 Do not expose this unit to sudden temperature changes from

cold to hot, and do not locate this unit in a environment with

high humidity (i.e. a room with a humidifier) to prevent

condensation inside this unit, which may cause an electrical

shock, fire, damage to this unit, and/or personal injury.

5 On the top of this unit, do not place:

– Other components, as they may cause damage and/or

discoloration on the surface of this unit.

– Burning objects (i.e. candles), as they may cause fire,

damage to this unit, and/or personal injury.

– Containers with liquid in them, as they may cause electrical

shock to the user and/or damage to this unit.

6 Do not cover this unit with a newspaper, tablecloth, curtain,

etc. in order not to obstruct heat radiation. If the temperature

inside this unit rises, it may cause fire, damage to this unit, and/

or personal injury.

7 Do not plug in this unit to a wall outlet until all connections are

complete.

8 Do not operate this unit upside-down. It may overheat, possibly

causing damage.

9 Do not use force on switches, knobs, and/or cords.

10 When disconnecting the power cord from the wall outlet, grasp

the plug; do not pull the cord.

11 Do not clean this unit with chemical solvents; this might

damage the finish. Use a clean, dry cloth.

12 Only the voltage specified on this unit must be used. Using this

unit with a higher voltage than specified is dangerous and may

cause fire, damage to this unit, and/or personal injury.

YAMAHA will not be held responsible for any damage

resulting from use of this unit with a voltage other than

specified.

13 To prevent damage by lightning, disconnect the power cord

from the wall outlet during an electrical storm.

14 Take care of this unit so that no foreign objects and/or liquid

drops inside this unit.

15 Do not attempt to modify or fix this unit. Contact qualified

YAMAHA service personnel when any service is needed. The

cabinet should never be opened for any reasons.

16 When not planning to use this unit for long periods of time (i.e.

vacation), disconnect the AC power plug from the wall outlet.

17 Be sure to read the “Troubleshooting” section on common

operating errors before concluding that this unit is faulty.

This unit is not disconnected from the AC power source as long

as it is connected to the wall outlet, even if this unit itself is

turned off. This state is called the standby mode. In this state,

this unit is designed to consume a very small quantity of power.

FREQUENCY STEP switch

(General and China models only)

Because the interstation frequency

spacing differs in different areas, set

the FREQUENCY STEP switch

(located at the rear) according to the

frequency spacing in your area.

Be sure to change the setting of this

switch with the AC supply lead of

this unit disconnected from the AC

outlet.

For CANADIAN CUSTOMERS

To prevent electric shock, match wide blade of plug to wide slot

and fully insert.

This Class B digital apparatus complies with Canadian ICES-

003.

Manufactured under license from Dolby Laboratories. “Dolby”,

“AC-3”, “Pro Logic” and the double-D symbol are trademarks of

Dolby Laboratories.

Manufactured under license from Digital Theater Systems, Inc. US

Pat. No. 5,451,942 and other world-wide patents issued and

pending. “DTS”, “DTS Digital Surround” and “DTS ES” are

DOLBY

DIGITAL

18 Before moving this unit, press STANDBY/ON to set this unit

in the standby mode, and disconnect the AC power plug from

the wall outlet.

FREQUENCY

STEP

50kHz

9kHz

100kHz

10kHz

English

Contents

Introduction 2

Getting Started..........................................................................................................3

Controls and Functions.............................................................................................4

Preparations 8

Speaker System Configurations ...............................................................................9

Hookups .................................................................................................................10

On-Screen Displays (OSD) .................................................................................... 19

Speaker Placement ................................................................................................. 20

Speaker Settings .....................................................................................................21

Speaker Output Levels ........................................................................................... 22

Basic Operation 24

Basic Playback ....................................................................................................... 25

AM/FM Tuner ........................................................................................................29

Basic Recording ..................................................................................................... 33

Advanced Operation 34

SET MENU Items ..................................................................................................35

Remote Control Features........................................................................................44

ZONE 2 .................................................................................................................. 55

Adjusting the Levels of the Effect Speakers ..........................................................57

Setting the Sleep Timer .......................................................................................... 57

Additional Information 58

Digital Sound Field Processing (DSP) ................................................................... 59

CINEMA-DSP .......................................................................................................61

DSP Parameter ....................................................................................................... 64

Appendix 68

Troubleshooting .....................................................................................................69

Specifications ......................................................................................................... 73

IntroductionPreparationsBasic Operation

Advanced

Operation

Additional

Information

Appendix

Welcome to the exciting world of digital home entertainment. This unit is the most complete and

advanced AV receiver available. Though some of the more advanced features of this unit may not be

familiar to you, they are easy to use. Incorporated state-of-the-art technology such as Dolby Digital and

DTS can bring the same audio experience to your home as they have brought to feature films in quality

theaters around the world. To make the listening experience even more enjoyable, this unit includes a

number of exclusive, digitally created listening environments known as digital sound fields. Choosing a

sound field program is like transporting yourself to such venues as an outdoor arena, a European church,

or a cozy jazz club. Take some time now to read more about these features and enjoy the new

experiences this unit brings to your home theater.

Introduction

Features

Dolby Digital and DTS decoder

Dolby Digital Matrix 6.1/DTS ES decoder

Digital Sound Fields (DSP)

CINEMA-DSP: Dolby Digital + DSP and DTS + DSP

Virtual CINEMA DSP and HP CINEMA DSP

Multi-function remote control

Built-in 8-channel power amplifier

Getting Started 3

Checking the Package Contents ............................................................................... 3

Installing Batteries in the Remote Control ............................................................... 3

Using the Remote Control........................................................................................ 3

Controls and Functions 4

Front Panel ............................................................................................................... 4

Display Indicators .................................................................................................... 5

Rear panel................................................................................................................. 6

Remote Control ........................................................................................................7

English

Getting Started

Checking the Package Contents

Check your package to make sure it has the following items.

Installing Batteries in the Remote Control

Insert the batteries in the correct direction by aligning the + and – marks on the batteries with the polarity illustrations (+ and –) inside the

battery compartment.

Change the batteries periodically. Do not use old batteries together with new ones.

Do not use different types of batteries (such as alkaline and manganese batteries) together. Read the packaging carefully as these different

types of batteries may have the same shape and color.

■About changing batteries

As the batteries wear out, the operating range of the remote control decreases and

the TRANSMIT indicator does not flash or its light becomes dim. When you

notice any of these conditions, change all of the batteries.

Notes:

• If the remote control is without batteries for more than 20 minutes, or if worn out

batteries remain in the unit, the contents of the memory may be cleared.

If the memory is cleared, insert new batteries and reprogram any functions that may have

been cleared.

• After you insert new batteries, be sure to push RESET in the battery compartment using

a ball point pen or similar object before using the remote control. (This does not clear the

contents of the memory.)

Using the Remote Control

The remote control transmits a directional infrared beam. Be sure to aim the remote control directly at the remote control sensor on the main

unit to operate. When the sensor is covered or there is a large object between the remote control and the main unit, the sensor cannot receive

signals. The sensor may not be able to receive signals properly when it is exposed to direct sunlight or a strong artificial light (such as a

fluorescent or strobe light). In this case, change the direction of the light or reposition the main unit to avoid direct lighting.

■About handling the remote control

Handle the remote control with care.

Do not spill water or other liquids on the remote control.

Do not drop the remote control.

Do not leave or store the remote control in the following types of conditions:

• high humidity or temperature such as near a heater, stove or bath; or

• dusty places; or

• in places subject to extremely low temperatures.

Remote Control

Alkaline Batteries (3) (LR6)

Quick Reference Guide

AM Loop Antenna

Power Cord

(U.S.A. and Canada

models only)

FM Antenna

(Australia and Singapore

models only)

Reset button

STANDBY

/ON

NATURAL SOUND AV RECEIVER RX–V3000

INPUT MODE

INPUT

VOLUME

SILENT

PHONES

SPEAKERS

PROCESSOR

DIRECT

BASS

EXTENSION

BASS TREBLE REC OUT/ZONE 2

VIDEO AUX

VCR 1

SAT

CABLE

D-TV/LD

DVD

SOURCE

/REMOTE

MD/TAPE

CD-R

TUNER

PHONO

VCR 2/DVR

EFFECT

6CH

INPUT

TUNING

MODE

MEMORY

S VIDEO VIDEO L R OPTICALAUDIO

MAN'L/AUTO FM AUTO/NAN'L MONO

FM/AM

PRESET

/TUNING

DSP

PROGRAM

EDIT

VIDEO AUX

30°30°

Approximately 6m

(20 feet)

FM Antenna

(U.S.A., Canada, China,

and General models only)

Power Cord

(Singapore model only)

Quick Reference Card

■ Remote Control ■ TUNER button (TUNER area) ■ CD button (CD area)

■ MD/TAPE button (MD area) ■ CD-R button (CD-R area)

V655120

Infrared window

CLEAR

RE-NAME

TRANSMIT

STANDBY

SYSTEM POWER

Display

Source selector

LIGHT

Operational buttons

10 KEY/DSP

Operational buttons

LEVEL

ON SCREEN

SLEEP

TEST

LEARN

MACRO

MACRO ON/OFF

button

Input buttons

6CH INPUT

Sound program selector/

Numeric buttons

MUTE

VOLUME +/–

EFFECT

PARAMETER/SET MENU

Cursor buttons

Cover

POWER

Preset number 1 to 8

Preset group A through E from left.

Preset group A/B/C/D/E

Preset +/–

(Set 10KEY)

POWER

DISPLAY

Skip Search

STOP

PLAY

PAUSE (/Stop)

Numeric buttons 1 to 9

Numeric button +10

Numeric button 0

DISC +/– (Disc Skip)

TV VOL +/–, TV INPUT, and TV MUTE

function if you have set up the

manufacturer code for the TV Area.

CLEAR

INDEX

(Set 10KEY)

POWER

REC/PAUSE

DISPLAY

Skip Search

Numeric buttons 1 to 9

Numeric button +10

Numeric button 0

(Set 10KEY)

STOP

PLAY

PAUSE

TV VOL +/–, TV INPUT, and TV MUTE

function if you have set up the

manufacturer code for the TV Area.

POWER

REC/PAUSE

DISPLAY

SOUND

Skip Search

STOP

PLAY

PAUSE

Numeric buttons 1 to 9

Numeric button +10

Numeric button 0

TV VOL +/–, TV INPUT, and TV MUTE

function if you have set up the

manufacturer code for the TV Area.

INDEX

(Set 10KEY)

When finding it difficult to fit this unit onto the shelf, remove the side panels after removing the screws tightened on the side panels. Put this

sticker to cover the screw holes after tearing off the back side of the sticker.

Side Panel Sticker

IntroductionPreparationsBasic Operation

Advanced

Operation

Additional

Information

Appendix

Controls and Functions

Front Panel

When you are not operating the controls behind the front panel door, close the door. To open the door, press gently on the lower part of the

panel.

STANDBY

/ON

NATURAL SOUND AV RECEIVER RX–V3000

INPUT MODE

INPUT

VOLUME

SILENT

PHONES

SPEAKERS

PROCESSOR

DIRECT

BASS

EXTENSION

BASS TREBLE REC OUT/ZONE 2

VIDEO AUX

VCR 1

SAT

CABLE

D-TV/LD

DVD

SOURCE

/REMOTE

MD/TAPE

CD-R

TUNER

PHONO

VCR 2/DVR

EFFECT

6CH

INPUT

TUNING

MODE

MEMORY

S VIDEO VIDEO L R OPTICALAUDIO

MAN'L/AUTO FM AUTO/NAN'L MONO

FM/AM

PRESET

/TUNING

DSP

PROGRAM

EDIT

VIDEO AUX

ZONE 2

BASS

STEREO

SLEEP

P.DIRECT

AUTO

MEMORY TUNED

D-TV/LD

DVD

CABLE

MD/TAPE

SAT CD-R

VCR 1 TUNER

VCR2/DVR

V-AUX PHONO

ZONE 2

BASS

STEREO

SLEEP

P.DIRECT

AUTO

MEMORY TUNED

w e

r

1 STANDBY/ON

Turns this unit on (On mode) and off (Standby mode). When

you turn on this unit, you will hear a click and there will be a

four to five second delay before this unit can reproduce sound.

In Standby mode, this unit consumes a small amount of power

to be ready to respond to the remote control.

2 Remote Control Sensor

3 INPUT MODE

Selects the type of audio signal for the selected source.

4 INPUT selector

Selects a source component.

5 VOLUME

Controls the output level of all audio channels. This does not

affect the REC OUT level.

6 PHONES

Outputs audio signals for private listening using headphones.

When you connect headphones, no signals are output to the

PREOUT jacks or the speakers.

7 SPEAKERS A/B

When SPEAKERS A/B is on, these buttons turn on the set of

Main speakers connected to the A and/or B terminals on the

rear panel.

8 BASS EXTENSION ON/OFF

When BASS EXTENSION is on, this feature boosts the bass

frequency of the left and right Main channels by +6dB (60Hz)

while maintaining overall tonal balance. This boost is useful if

you do not use a subwoofer. However, this boost may not be

noticeable if the Main speakers are set to “SMALL” and the

bass output mode is set to “SWFR.”

9 PROCESSOR DIRECT ON/OFF

When PROCESSOR DIRECT is on, BASS, TREBLE,

BALANCE, and BASS EXTENSION are bypassed,

eliminating any alteration of the original signal.

0 BASS

Adjusts the low frequency response for the left and right Main

speaker channels. Turn the control to the right to increase the

low frequency response and turn the control to the left to

decrease the low frequency response.

English

q TREBLE

Adjusts the high frequency response for the left and right Main

channels. Turn the control to the right to increase the high

frequency response.

w REC OUT/ZONE 2

Selects the source you want to direct to the audio/video

recorder.

e EFFECT

Switches the effect speakers (Center, Front Effect, Rear and

Rear Center) on and off. If you turn off the output of these

speakers using EFFECT, all DTS and Dolby Digital audio

signals are directed to the Main left and right channels except

for the LFE channel.

r 6CH INPUT

Switches between 6CH INPUT mode and normal input modes.

6CH INPUT mode takes priority over the source selected with

the INPUT selector. You cannot use DSP sound field programs

while using an external decoder.

t VIDEO AUX

Inputs audio and video signals from a portable external source

such as a video camera. To reproduce source signals from these

jacks, select V-AUX as the input source. To direct this source

to the VCR 1 and VCR 2/DVR output jacks, select VIDEO

AUX using REC OUT.

y FM/AM

Switches the reception band between FM and AM.

u Multi jog knob

Selects the tuning frequency in the tuning mode.

Selects the preset station after pressing PRESET/TUNING to

display a colon (:) in the tuning mode.

Selects the DSP program after pressing DSP PROGRAM.

i MEMORY (MAN’L/AUTO FM)

Stores a station in the memory.

o TUNING MODE (AUTO/MAN’L MONO)

Switches the tuning mode between automatic and manual. To

select the automatic tuning mode, press this button so that the

AUTO tuning indicator appears in the front panel display (the

STEREO indicator also appears if receiving a stereo broadcast).

To select the manual tuning mode, press this button so that the

AUTO tuning indicator does not appear.

Display Indicators

1 Processor indicators

When any function of DTS/VIRTUAL/Dolby Digital/Dolby

PROLOGIC/DSP/Dolby Digital Matrix 6.1/DTS ES is

operating, its indicator lights up.

2 PCM

Lights up when this unit is reproducing PCM (Pulse Code

Modulation) digital audio signals.

3 SPEAKERS A/B

Lights up according to which set of Main speakers is selected.

Both indicators light up when both sets of speakers are selected.

4 Headphones

Lights up when headphones are connected.

5 Multi-information display

Shows the current DSP program and other information when

adjusting or changing settings.

6 Input source

Shows the current input source with the arrow-shaped cursor.

7 BASS

Lights up while the BASS EXTENSION is on.

8 SLEEP

Lights up while the Sleep Timer is on.

9 P. DIRECT

Lights up while the PROCESSOR DIRECT is on.

0 STEREO

Lights up when the AUTO tuning indicator is on and the unit is

receiving a strong signal for an FM stereo broadcast.

q MEMORY

Flashes to show a station can be saved.

w TUNED

Lights up when this unit tunes into a station.

e AUTO

Shows that the Tuner is in Automatic tuning mode.

r ZONE 2

Lights up when you select the input source while the remote

control is in the Zone 2 mode.

Controls and Functions

IntroductionPreparationsBasic Operation

Advanced

Operation

Additional

Information

Appendix

Controls and Functions

OPTICAL

MD/TAPE

CENTER

CAUTION

SEE INSTRUCTION MANUAL FOR CORRECT SETTING.

TUNER

FM ANT

75Ω

UNBAL.

ANT

– GND

IMPEDANCE SELECTOR

SET BEFORE POWER ON

FRONT

REAR

REAR CENTER

CENTER

MAIN A OR B

A + B

: 6

Ω

MIN./SPEAKER

: 4

Ω

MIN./SPEAKER

: 4

Ω

MIN./SPEAKER

: 4

Ω

MIN./SPEAKER

: 4

Ω

MIN./SPEAKER

: 8

Ω

MIN./SPEAKER

FRONT

REAR

REAR CENTER

CENTER

MAIN A OR B

A + B

: 8

Ω

MIN./SPEAKER

: 8

Ω

MIN./SPEAKER

: 8

Ω

MIN./SPEAKER

: 8

Ω

MIN./SPEAKER

: 8

Ω

MIN./SPEAKER

: 16

Ω

MIN./SPEAKER

CTRL OUT

+5V

100Ω 20mA

REMOTE

ZONE 2 OUT

2t9

Rear panel

1 Audio component jacks

2 Video component jacks

3 Antenna input terminals

4 Speaker terminals

5 AC OUTLETS

Use these outlets to supply power to your other audio/video

component.

6 IMPEDANCE SELECTOR

7 DIGITAL OPTICAL/COAXIAL jacks

8 6CH INPUT jacks

9 PRE OUT/MAIN IN jacks

0 AC power cord

Connect to a power outlet.

General, China, and Australia models cannot disconnect the AC

power cord from the unit.

q GROUND terminal

w RS232C/CTRL OUT +5V terminals

These are control expansion terminals for Substitute Custom

Installation use. Consult your dealer for details.

e REMOTE IN/OUT jacks

r q RF (AC-3) input jack

General, China, and Singapore models only.

t ZONE 2 OUT jack

(Singapore model)

English

Controls and Functions

Remote Control

1 CLEAR

Erases the content of learning.

2 RE-NAME

Renames the input name.

3 TRANSMIT

Flashes while the remote control is sending signals.

4 LEARN

Starts the learning function.

5 MACRO

Makes the MACRO setting.

6 MACRO ON/OFF

Turns the macro function on and off.

7 Input buttons

Selects the input source for playback.

8 6CH INPUT

Switches to the 6CH INPUT mode when using an external

decoder.

9 Operational buttons

Performs the operation selected by input selector.

Sound program selector/Numeric buttons

Selects the sound program.

q MUTE

Mutes the sound. Press again to restore audio output at the

previous volume level.

w VOLUME +/–

Increases or decreases the volume level.

e EFFECT

Switches the effect speakers (Center, Front, Rear, and Rear

Center) on and off.

r PARAMETER/SET MENU

Selects the PARAMETER mode or SET MENU mode.

t Cursor buttons

Selects and adjusts DSP program parameters and SET MENU

items according to the position of PARAMETER/SET MENU.

y STANDBY

Turns off the power.

u SYSTEM POWER

Turns on the power.

i Display

Displays the input or operation status.

o Source selector

Selects the source component.

p 10 KEY/DSP

Selects the numeric button mode or DSP program mode.

a LEVEL

Selects the effect speaker channel to be adjusted and sets the

level.

s ON SCREEN

Selects the On-Screen Display mode for your video monitor.

d SLEEP

Sets the sleep timer.

f TEST

Outputs the test tone to adjust the speaker levels.

g Infrared window

h LIGHT

Turns the light on or off. When you press this button once, the

light turns on for about ten seconds. Press again to turn off the

light.

j Cover

k Å button

Switches the control area.

IntroductionPreparationsBasic Operation

Advanced

Operation

Additional

Information

Appendix

Preparations

Speaker System Configurations 9

Hookups 10

Connecting Audio Components ............................................................................. 10

Connecting Video Components ............................................................................. 12

Connecting Speakers .............................................................................................. 14

Connecting Subwoofers ......................................................................................... 16

Connecting an External Decoder............................................................................ 17

Connecting External Amplifiers............................................................................. 17

Others ..................................................................................................................... 18

On-Screen Displays (OSD) 19

OSD Modes ............................................................................................................19

Selecting the OSD Mode........................................................................................ 19

Speaker Placement 20

Speaker Settings 21

Speaker Output Levels 22

Before You Begin................................................................................................... 22

Dolby Surround Test .............................................................................................. 22

DSP Test................................................................................................................. 23

English

Speaker System Configurations

The most complete speaker configuration consists of eight speakers: the left and right Main speakers, a Center speaker, the left and right Rear

speakers, the left and right Front Effect speakers, and a Rear Center speaker. If you do not use eight speakers, you can direct the signals for

speakers that are not in your system to other speakers in your configuration. A Subwoofer can be used with any of these configurations to

produce a fuller sound.

■Eight or Seven Speaker Configuration

–Full Cinema DSP–

When you reproduce feature film software, this configuration fully expresses the

powerful and realistic sound qualities of 70 mm multitrack audio. The dialogue is

positioned as if it were coming from directly on the screen, the sound effect is

positioned slightly behind the screen, and the soundtrack music is positioned even

further behind the screen to express the width and depth of the overall presentation.

This configuration makes the most of this unit’s capability.

The Rear Center speaker is useful for playback of 6-channel Digital Surround.

■Six Speaker Configuration –Hi Fi DSP–

This configuration is used the most for audio playback with HiFi DSP. It does not

position the dialogue sound as well as a seven or eight speaker configuration.

However, it creates a dynamic DSP (Digital Sound Field Processor) sound field

which adds depth to the sound.

For this speaker configuration, change SET MENU item 1A. CENTER SP to

“NONE” and 1D. REAR CT SP to “NONE”.

■Five Speaker Configuration –Standard 5.1 Channel–

This configuration does not express the height of the sound field as well as the

seven or eight speaker configuration. However, it positions the dialogue sound as

coming directly from the screen.

For this speaker configuration, change SET MENU item 1F. FRNT EFCT SP to

“NONE” and 1D. REAR CT SP to “NONE”.

■Four Speaker Configuration

–Minimum Requirement–

In this configuration, the Center speaker signals and Front Effect speaker signals

are directed to the left and right Main speakers.

For this speaker configuration, change SET MENU item 1A. CENTER SP to

“NONE,” item 1F. FRNT EFCT SP to “NONE,” and item 1D. REAR CT SP to

“NONE”.

Front Effect Speakers

Center Speaker

Front Subwoofer

Main Speakers

Rear Speakers

Rear Center Speaker

Rear Subwoofer

( )

IntroductionPreparationsBasic Operation

Advanced

Operation

Additional

Information

Appendix

Hookups

Connecting Audio Components

Before you connect any components, disconnect the power supply to all the components you plan to connect including this unit and

determine which jacks are for the left and right channels and for input and output.

When you connect other YAMAHA audio component (such as a CD player or changer, MD deck, or tape deck), connect to terminals with

the same number labels. Yamaha applies this labelling system to all its products.

In the hookup illustrations on the following pages:

■Connecting to digital jacks

This unit has digital jacks for direct transmission of digital signals through either coaxial or fiber optic cables. You can use the digital jacks

to input PCM, DTS, and Dolby Digital bitstreams. When you connect components to both the COAXIAL and OPTICAL jacks (for CD and

CABLE) priority is given to the input signals from the COAXIAL jack. All digital input jacks are acceptable for 96 kHz/24 bit digital

signals.

■About the dust protection cap

Pull out the cap from the optical jack before you connect the fiber optic cable. Do

not discard the cap. When you are not using the optical jack, be sure to put the cap

back in place. This cap protects the jack from dust.

The OPTICAL jacks on this unit conform to the EIA standard. If you use a fiber

optic cable that does not conform to this standard, this unit may not function

properly.

■Connecting a turntable

These jacks are for connecting a turntable with an MM or high output MC

cartridge. If you have a turntable with a low output MC cartridge, use an inline

boosting transformer or MC-head amplifier when connecting to these jacks.

The GND terminal does not electrically ground the turntable. It simply reduces

noise in the signal. In some cases, you may hear less noise if you do not connect to

the GND terminal.

■Connecting a CD player

• The COAXIAL CD and OPTICAL CD jacks are available for a CD player

which has coaxial or optical digital outputs.

• When you connect a CD player to both the COAXIAL CD and OPTICAL CD

jacks, priority is given to the input signals from the COAXIAL CD jack.

■Connecting an MD or DAT deck

• When you connect a recorder to this unit, keep the deck’s power on while using

this unit. If the power is off, this unit may distort the sound from other

component.

• When you record from source component connected to this unit while this unit’s

power is off, the recorded sound may be distorted. To avoid this problem, turn

on this unit.

• When you connect a CD recorder to both the analog and digital input and output

jacks, priority is given to the digital signals.

English

Hookups

OPTICAL

OUT (REC)

CENTER

ZONE 2 OUT

CTRL OUT

+5V

100Ω 20mA

OUTPUT

INPUT

GROUND

OPTICAL

OUTPUT

OPTICAL

INPUT

OPTICAL

INPUT

OPTICAL

OUTPUT

COAXIAL

OUTPUT

MD/TAPE

recorder

CD recorder

CD player

Turntable

to/from External

Amplifier

to/from External

Controller

from External

Decoder

(Singapore model)

IntroductionPreparationsBasic Operation

Advanced

Operation

Additional

Information

Appendix

Hookups

Connecting Video Components

Before you connect any components, disconnect the power supply to all the components you plan to connect including this unit and

determine which jacks are for the left and right channels and for input and output. After you finish all hookups, check them again to make

sure they are correct.

■About the video jacks

There are three types of video jacks. Video signals input through the VIDEO jacks are the conventional composite video signals. Video

signals input through the S VIDEO jacks are separated into luminance (Y) and color (C) video signals. The S-video signals achieve high

quality color reproduction.

Video signals input through the COMPONENT VIDEO jacks are separated into luminance (Y) and color difference (P

B/CB, PR/CR) video

signals. The jacks are also separated into three for each signal. The labels of the component video jacks may be different depending on the

component (e.g. Y, C

B, CR / Y, PB, PR / Y, B-Y, R-Y/ etc.). Component video signals provide the best quality in picture reproduction.

If your video component has an S-video output or component video output, you can

connect it to this unit. Connect the S-video signal output jack on your video

component to the S-VIDEO jack or connect the component signal output jacks on

your video component to the COMPONENT VIDEO jacks.

Notes:

• Each type of video jack works independently. Signals input through the composite video,

S-video, and component jacks are output through the corresponding composite video, S-

video, and component jacks respectively.

• Use a commercially available S-video cable when connecting to the S VIDEO jacks, and

commercially available video cables when connecting to the COMPONENT VIDEO

jacks.

• When you are using the COMPONENT VIDEO jacks, check the details in the owner’s

manual that came with the component being connected.

Composite VIDEO jack

S VIDEO jack

COMPONENT VIDEO jacks

English

Hookups

OPTICAL

OUT (REC)

CENTER

ZONE 2 OUT

CTRL OUT

+5V

100Ω 20mA

VIDEO

OUTPUT

COMPONENT

INPUT

AUDIO

OUTPUT

AUDIO

INPUT

S VIDEO

INPUT

VIDEO

INPUT

S VIDEO

INPUT

VIDEO

INPUT

S VIDEO

OUTPUT

S VIDEO

OUTPUT

VIDEO

OUTPUT

S VIDEO

OUTPUT

VIDEO

OUTPUT

S VIDEO

OUTPUT

COMPONENT

OUTPUT

COMPONENT

OUTPUT

AUDIO

OUTPUT

AUDIO

OUTPUT

AUDIO

OUTPUT

OPTICAL

OUTPUT

OPTICAL

OUTPUT

SAT OPTICAL

OUTPUT

<Video>

<RF>

<Video>

VIDEO

OUTPUT

CABLE COAXIAL

OUTPUT

DVD player

DTV/LD player

Cable TV/SAT

VCR 1/2

Monitor

RF-Signal Output*

(General, China and Singapore

models only)

* <U.S.A., Canada, and Australia models>

If your LD player has a Dolby Digital RF signal output jack, connect it to this unit through an external RF demodulator.

(You can connect the Dolby Digital RF signal output of your LD player to the COAXIAL jacks using the “I/O ASSIGN” on the SET

MENU.)

IntroductionPreparationsBasic Operation

Advanced

Operation

Additional

Information

Appendix

Hookups

Connecting Speakers

This section explains how to connect speakers to this unit. After you finish connecting your speakers, use the SET MENU to change the

signal output settings according to the number and size of the speakers in your configuration.

Before connecting any speaker cords, identify which terminals are for the right and left channels and also the + and – polarities. If you

connect speakers with the wrong polarity (+ to –), this unit will not reproduce clear sound.

■Using speaker cords

A speaker cord is actually a pair of insulated cables running side by side. One of

the cables is colored or shaped differently, perhaps with a stripe, groove, or ridge.

To make sure you always connect speakers with the correct polarity, determine the

difference between the cables of your speaker cord, make a note of which cable

you plan to use for which polarity (+ and –), and always connect the speaker cords

consistently.

Strip off 9 mm (3/8 in.) of an inch of insulation from the ends of the cables.

Twist the exposed wires of the cable together to prevent short circuits.

Loosen the terminal knob by turning it counterclockwise.

Insert only the exposed portion of the cable into the slot in the side of the

terminal, and tighten the terminal knob.

Note:

• If your speaker cords have banana plugs, tighten the terminal knob and insert the

plug into the end of the terminal. (Except for Singapore model)

Caution:

• Connect the speaker cords with care to avoid creating a short circuit. If you turn on

the power and there is a short circuit, this unit may be damaged even though the

protection circuit automatically shuts off the power.

■About the q RF (AC-3) signal input jack <For China, Singapore, and General models only.>

If your LD player has an q RF (AC-3) signal output jack, connect it to the q RF (AC-3) input jack on this unit. For this connection,

change SET MENU item 7D. COAXIAL IN (10) to “LD-RF”. If q RF (AC-3) and analog signals are input at the same time, priority is

given to the RF signals. When you want to reproduce q RF (AC-3) signals, set the input mode to “D.D. RF” using INPUT MODE.

Note:

• q RF (AC-3) signals cannot be output using the REC OUT selector. When you record

sound or images from an LD player, be sure to connect the player to either the DIGITAL

OPTICAL or analog AUDIO jacks.

Caution:

• Even if you connect an LD player with an q RF (AC-3) output jack to this unit, you

cannot reproduce Dolby Digital sound from all LD discs. You must playback an LD disc

encoded with Dolby Digital signals in order to take advantage of the Dolby Digital

sound.

Banana Plug

(Except for Singapore model)

English

Hookups

Right Front

Speaker

Left Front

Speaker

Rear Center

Speaker

Right Rear

Speaker

Left Rear

Speaker

To other component

Subwoofer

system

Right Main B

Speaker

Left Main B

Speaker

Right Main A

Speaker

Left Main A

Speaker

Center Speaker

CAUTION

SEE INSTRUCTION MANUAL FOR CORRECT SETTING.

TUNER

FM ANT

75Ω

UNBAL.

ANT

– GND

IMPEDANCE SELECTOR

SET BEFORE POWER ON

FRONT

REAR

REAR CENTER

CENTER

MAIN A OR B

A + B

: 6

Ω

MIN./SPEAKER

: 4

Ω

MIN./SPEAKER

: 4

Ω

MIN./SPEAKER

: 4

Ω

MIN./SPEAKER

: 4

Ω

MIN./SPEAKER

: 8

Ω

MIN./SPEAKER

FRONT

REAR

REAR CENTER

CENTER

MAIN A OR B

A + B

: 8

Ω

MIN./SPEAKER

: 8

Ω

MIN./SPEAKER

: 8

Ω

MIN./SPEAKER

: 8

Ω

MIN./SPEAKER

: 8

Ω

MIN./SPEAKER

: 16

Ω

MIN./SPEAKER

(Singapore model)

IntroductionPreparationsBasic Operation

Advanced

Operation

Additional

Information

Appendix

Hookups

Connecting Subwoofers

■Connecting a front subwoofer

Connect the signal input jack on your subwoofer to one of the PRE OUT/

MAIN IN SUBWOOFER jacks.

Notes:

• The SUBWOOFER jacks (output) have a built-in high cut-off filter (90 Hz). When

using a powered subwoofer, set the high cut-off frequency to “MAX” on your

Subwoofer.

• Both SUBWOOFER jacks output the same signal.

■Connecting a rear subwoofer

By using both Front and Rear Subwoofers, the CINEMA-DSP sound field

programs can produce realistic movie effects with powerful, dynamic sound. To

take advantage of this dynamic sound, be sure to set the 1C. REAR L/R SP item in

the SET MENU to “LARGE”, and connect your Rear speakers and Subwoofer as

described below.

Connect the right + input terminal on your Subwoofer to the REAR R +

terminal, and the right – input terminal on your Subwoofer to the REAR R –

terminal with speaker cords.

Connect the left + input terminal on your Subwoofer to the REAR L +

terminal, and the left – input terminal on your Subwoofer to the REAR L –

terminal with speaker cords.

Connect your Rear speakers to the output terminals on the Rear Subwoofer.

Be sure to connect the Rear speakers to the Subwoofer with the correct

polarity.

Note:

• Adjust the speaker volume for the Subwoofer with the controls on the Subwoofers,

not on this unit.

CENTER

Subwoofer system

Right Rear

Speaker

Left Rear

Speaker

Sidan laddas ...

Yamaha RXV3000 Användarmanual

varumärke: Yamaha

Modell: RXV3000

Kategori: AV-mottagare

Typ: Användarmanual

Denna manual är också lämplig för

Ladda ner pdf

Rapportera

på andra språk

italiano: Yamaha RXV3000 Manuale utente
čeština: Yamaha RXV3000 Uživatelský manuál
español: Yamaha RXV3000 Manual de usuario
Deutsch: Yamaha RXV3000 Benutzerhandbuch
polski: Yamaha RXV3000 Instrukcja obsługi
português: Yamaha RXV3000 Manual do usuário
français: Yamaha RXV3000 Manuel utilisateur
Türkçe: Yamaha RXV3000 Kullanım kılavuzu
English: Yamaha RXV3000 User manual
dansk: Yamaha RXV3000 Brugermanual
русский: Yamaha RXV3000 Руководство пользователя
suomi: Yamaha RXV3000 Ohjekirja
Nederlands: Yamaha RXV3000 Handleiding
română: Yamaha RXV3000 Manual de utilizare

Yamaha RXV3000 Användarmanual

Denna manual är också lämplig för

Yamaha RXV3000 Användarmanual

på andra språk

Relaterade papper

Andra dokument