Boston Acoustics Horizon Solo Användarmanual

OWNER’S MANUAL / SAFETY INSTRUCTIONS / COMPLIANCE INFORMATION

A Boston P.O.P. Product Make it your own...

Horizon Solo XT

High Performance DAB/FM Radio

An about-face in radio design

Español

Radio DAB/FM de alta performance

Innovación total en diseño de radios

Français

Radio AM/FM à haute performance

Un changement majeur dans la

conception des appareils radio

Italiano

Radio DAB/FM ad alte prestazioni

Una rivoluzione nel mondo delle radio

Svenska

Högpresterande DAB/FM-radio

En helomvändning inom radiodesign

Deutsch

Hochleistungsfähiges DAB/FM-radio

Innovatives Radiodesigns

2

17. Either the power inlet connector on the rear of the

apparatus or the power plug at the wall must remain

accessible, to be able to disconnect power from the

apparatus.

18. To completely disconnect this apparatus from the AC

Mains, disconnect the power supply cord plug from the

AC receptacle.

19. The mains plug of the power supply cord shall remain

readily operable.

American Users:

Note: This equipment has been tested and found to

comply with the limits for a Class B digital device, pursuant

to part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference

in a residential installation. This equipment generates, uses,

and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause

harmful interference to radio communications. However,

there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be

determined by turning the equipment o and on, the user

is encouraged to try to correct the interference by one or

more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and

receiver.

• Connect the equipment into an outlet on a circuit

di erent from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV

technician for help.

Caution: Unauthorized changes or modi cations to

the receiver could void user’s authority to operate the

equipment.

Canadian Users

This class B digital apparatus complies with Canadian

ICES-003.

Cet appareil numérique de classe B est conforme á la norme

NMB-003 du Canada.

IMPORTANT SAFETY INSTRUCTIONS

This symbol found on the apparatus indicates

hazards arising from dangerous voltages.

This symbol found on the apparatus indicates the

user should read all safety statements found in the

user manual.

This symbol found on the apparatus indicates

double insulation.

Warning! To reduce the risk of  re or electrical

shock, do not expose this apparatus to rain or

moisture.

This symbol found on the apparatus indicates

that the apparatus must be placed in a separate

collection facility for electronic waste and not

disposed with household waste.

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in

accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators,

heat registers, stoves, or other apparatus (including

ampli ers) that produce heat.

9. Do not defeat the safety purpose of the polarized or

grounding type plug. A polarized plug has two blades

with one wider than the other. A grounding-type plug

has two blades and a third grounding prong. The wide

blade or the third prong is provided for your safety. If

the provided plug does not  t into your outlet, consult

an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or

pinched particularly at plugs, convenience receptacles,

and the point where they exit from the apparatus.

11. Only use attachments/accessories speci ed by the

manufacturer.

12. Unplug this apparatus during lightning storms or when

unused for long periods of time.

13. Refer all servicing to quali ed service personnel.

Servicing is required when the apparatus has been

damaged in any way, such as power-supply cord or

plug is damaged, liquid has been spilled or objects

have fallen into the apparatus, the apparatus has been

exposed to rain or moisture, does not operate normally,

or has been dropped.

14. Maintain a minimum distance of 2” (50mm) around

the front, rear, and sides of the apparatus for su cient

ventilation. The ventilation should not be impeded

by covering the ventilation openings or placing on or

around the apparatus items such as newspapers, table-

cloths, curtains, etc.

15. No open  ame sources, such as lighted candles, should

be placed on the apparatus.

16. The apparatus shall not be exposed to dripping or

splashing. No objects  lled with liquids, such as vases,

shall be placed on the apparatus.

E

N

G

L

I

S

H

3

Introduction

Thank you for choosing Boston Acoustics and congratulations on your purchase of the Horizon Solo XT High

Performance Tabletop DAB Radio. If you own other Boston products, the outstanding audio performance

and ease-of-use of the Solo XT should come as no surprise. If you’re new to Boston, welcome -- we think

you’ve made a great choice. The Solo XT is a sophisticated DAB/FM radio with dual alarms, aux in and line/

headphone outputs, all in a high-style, soft-touch enclosure -- all the things “Play Smart.” So check out all the

features and functions of your new music system. We know you’ll enjoy it for years to come.

Features

• Outstanding audio performance from a 3

1

/2-inch speaker in a vented acoustic chamber

• BassTrac® audio processing for satisfying bass at any volume

• Three intuitive, easy to use controls operate all the Solo XT features

• Large, easy to read display with adjustable brightness that dims automatically in low light conditions

• Highly sensitive DAB/FM Stereo tuner

• 20 radio station presets

• Supports DAB Band III and L-Band for a wide variety of digital radio stations

• High performance antenna is included; can also be used with an external antenna

• Dual alarm functions each with wake-to-alarm and / or wake-to-radio

• Alarms gradually increase in volume for a gentle wake up

• S-n-o-o-o-o-o-z-e bar - the entire front aluminum trim is a touch-sensitive, can’t-miss-it snooze bar

• Sleep function lets you listen to the radio for up to 90 minutes before the Solo XT turns itself o

• Make it your own! Customize your Solo XT with optional grilles available at bostonacoustic.com/POP

• Time setting, station presets and alarms settings are remembered during power outages

• Front panel headphone output jack

• Auxiliary audio input for portable music players

• Internal power supply - no bulky external adapter needed

B/A ellipse symbol, make it your own, and Play Smart are trademarks of Boston Acoustics, Inc.

4

Unpacking and Setting Up Your Horizon Solo XT

Carefully unpack Horizon Solo XT. If there is any sign of damage from transit, report it immediately to your

dealer and/or delivery service. Keep the shipping carton and packing materials for future use. Be sure to

keep your purchase receipt in a safe place, as it may be required for warranty purposes.

In the box you should  nd the Solo XT (with the antenna attached) and the power cord.

Placement

Your Horizon Solo XT will sound great just about anywhere. But if you put it near a wall or corner the bass

response will be enhanced. Blocking the bass port will result in a loss of performance.

Horizontal or Vertical Position

The Solo XT control panel can be rotated to allow for

horizontal or vertical use. If you want to change the

orientation of the radio, grasp the ring around the

control panel and turn it 90°.

Contents

Unpacking and Setting Up Your Horizon Solo XT 4

Placement 4

Horizontal or Vertical Position 4

Power Connection 5

Antenna 5

About the Front Panel Controls 5

Basic Control Operations 6

Turning the Solo XT On or O 6

Adjusting the Volume 6

Selecting Sources or Setup Functions 6

About the Setup Options Functions 6

Setting the Clock, Time, Date and

Related Functions 7

FM Radio 7

Tuning in an FM Station 7

FM Station Seek 7

DAB Radio 8

The DAB Station List 8

Tuning in a DAB Station 8

The DAB Display 8

DAB Station Setup 9

About Station Presets 9

Setting a Station Preset 10

Tuning in a Preset Station 10

Removing One or More Presets 10

Alarm Clock Features 10

Alarm Setup 10

Turning Alarms On or O 11

How the Alarms Work 11

The Snooze Feature 11

Sleep Function 12

Audio Controls 12

Display Controls 13

Resetting To Factory Default 14

Connecting Other Equipment 14

Connecting Headphones 14

Using Aux Inputs 14

Line Output 14

Security Cable Connection 14

About Clock Memory 14

Limited Warranty 15

If Service Seems Necessary 15

5

Power Connection

Just connect the power cord to the back of the Solo XT and

plug it into a power outlet.

Antenna

The Horizon Solo XT is shipped with an extendable antenna

connected to a rear panel input.

Note: Boston Acoustics has found that in situations where

the supplied antenna is not used with the product, strong

signals can interfere with normal performance.

DAB/FM Antenna

AC Input

Aux Input

Line Output

About the Front Panel Controls

Almost all of the Horizon Solo XT functions are operated by the three controls on the front panel.

Power/Volume – Is controlled by the large knob centered

low on the panel.

Mode/Info – Selects the input you want to use or the

function you want to adjust.

Tune – Tunes in a new radio station.

These logical, intuitive controls make it easy to operate the

Horizon Solo XT. The way you use them is the same for each

feature. Once you learn how to control one of the features

the rest of them will be easy. You may not need to refer

to this manual once you understand the way the controls

work.

6

Basic Control Operations

Turning the Solo XT On or O

Press the POWER/VOLUME control on the center of the front

panel.

Adjusting the Volume

Turn the front panel POWER/VOLUME knob.

Note: On the control illustrations –

Regular arrows indicate to press and release

the button or control.

Double headed arrows indicate to press and hold

the button or control.

Selecting Sources or Setup Functions

Use the MODE/INFO control to select the source you want to listen to or access the “DAB Setup” or “Setup

Options” menus.

1

Turn the MODE/INFO control to display the “Mode”

menu. Highlight the source you want to hear or the

setup menu you want to use.

2

Press the MODE/INFO control to select the highlighted

item.

Note: The “Setup Option” selection is not shown in the

initial display. Move the highlight box past the “DAB Setup”

selection to access “Setup Options” .





This illustration shows the DAB radio

source highlighted for selection.

About the Setup Options Functions

When you select “Setup Options” from the “Mode” menu the “Setup Options” menu is displayed. Initially the

display shown below on the left appears. Turn the MODE/INFO control to move the highlight box. If you turn

the MODE/INFO control until the highlight box moves past the “Display” menu item, more menu items appear,

as shown in the display on the right.

In this display the Alarm 1

function is highlighted for selection.

In this display the Audio control

function is highlighted for selection.

In the next section the procedure for setting the clock is described. Other Setup function are described in

later sections. Once you know how to set up one of the Mode functions the others will be easy.

7

Setting the Clock, Time, Date and Related Functions

1

Turn the MODE/INFO control to highlight “Setup Options”

then press the control.

2

Turn the MODE/INFO control to highlight “Clock” then press

the control. You’ll see the menu screen shown at the right.

3

Turn the MODE/INFO control to move the highlight box to

the function you want, then press the control to select it.

4

Once the function you want is selected, turn the MODE/

INFO

or TUNE control to change the setting, then press the

control.

Note: There are additional menu selections not shown in this display example. Move the highlight box past

the “Year” menu item to select the “Month” and “Day” setting functions or the Exit function.

The settings on the “Clock Setup” menu are:

Auto: Yes/No – Select “Yes” to let the Solo XT set the time, year, month, and

day automatically using signals from a DAB station. Select “No” to set the clock

manually.

Format: 12 Hour/24 Hour – Sets the clock display to 12 hour or 24 hour

format.

Time: Sets the time.

Year: Sets the year.

Month: Jan-Dec – Sets the month.

Day: 1-31 – Sets the day of the month. The selection range depends on the

month. The February 29 on leap years is programmed into the clock.

Exit: Returns to the default display.

Note: If you manually adjust the Time, Year, Month or Day after you have set Auto to “Yes”, the setting

changes to “No”. Subsequent clock/calendar settings have to be done manually.

FM Radio

Tuning in an FM Station

1

Turn the MODE/INFO control to highlight “FM”. Press the control

2

Turn the TUNE control until the station frequency you want

shows in the display.

Note: If the station you select has been assigned to a station preset

the Preset indicator and number are displayed. See the next page for

more information.

FM Station Seek

Press the TUNE control. The Solo XT will seek up the radio band for

the next receivable station.

8

DAB Radio

The DAB Station List

When you plug in the Solo XT for the  rst time it automatically searches the DAB radio bands for stations

and puts the available stations in a list. If you move the Solo XT to a new location you can use the DAB

Scan feature to reset the station list. You can also manually tune to the station list available on speci c DAB

multiplex bands. For more information see the “DAB Station Setup” on the following page.

Tuning in a DAB Station

1

Turn the MODE/INFO control to highlight “DAB”. Press the

control

2

Turn the TUNE control to display the list of available

stations.

3

Highlight the station you want and press the TUNE

control to select it.

Notes:

Only stations that were put in your station list by the initial

automatic station scan, a scan you perform with the DAB Scan

function, or that you tune manually are displayed as you turn the TUNE control.

You can change the order in which the stations are displayed. See the “DAB Display” and “Display Menu”

sections on the following pages.

The DAB Display

When using the DAB radio the display shows a

variety of information. In the main part of the

display the  rst line is station name.

The second line of the display center shows one of the following:

Genre — Signal Quality (in %) — Compression — Network — Frequency — Date and Time.

You can set the default information you want to appear in this line. See the “Display Menu” section of this

manual. In addition you can change the information in the second line by pressing the MODE/INFO control.

Each press switches to the next information mode.

The  nal line will always be scrolling text information provided by broadcast station.

 



Time

Signal Strength

Preset (if assigned)

Station Name

Varying Information

Scrolling Text

9

DAB Station Setup

If you move the Solo XT to a new location you can use the DAB Scan feature to reset the station list. You can

also manually select stations to add to the list.

1

Turn the MODE/INFO control to highlight “DAB Setup” . Press

the control.

Note: If the DAB radio source is selected you can simply

press the

TUNE control to access the “DAB Setup” menu.

2

Turn the MODE/INFO control to highlight “Full Scan”, “Quick

Scan” or “Manual Tune”. Press the control.

DAB Order: Active/Alphanum/Favorite/Multiplex – Active -

Displays active stations  rst. Alphanum(eric) - displays stations in

alphanumeric order. Favorite - displays stations most listened to

 rst. Multiplex - displays stations in Multiplex order.

Full Scan: Searches all 64 frequencies in the Band III and L Band

groups.

Quick Scan: Searches only the most commonly used frequencies in Band III - from 10B (211.648 MHz) to 13B

(232.496 Mhz).

During the scanning processes the display shows the station multiplex as it is scanned.

Manual Tune: This option displays a list of all the DAB multiplexes. Turn

the MODE/INFO control to highlight the multiplex you want, then press the

control.

This example shows Quick Scan

highlighted for selection.

This example shows station 5C

highlighted for selection.

About Station Presets

The Solo XT has 20 station presets. The presets can be used to store either FM or DAB stations. Because of

the way the Solo XT places stations in the presets you may want to plan how you store them. Here’s how it

works. The  rst station you store goes into Preset 1. The second station goes into Preset 2 and so on, up to 20

stations. If you remove a preset all the stations in presets above the one you removed, drop down a preset

position. The table below gives an example.

Preset # 1 2 3 4 5 6 7

originally programmed stations FM 89.70 FM 90.95 FM 100.30 FM 104.95 DAB 211.648 DAB 217.088 DAB 222.064

after removing presets 2 and 6 FM 89.70 FM 100.30 FM 104.95 DAB 211.648 DAB 222.064

It may be helpful to put the presets in some logical order. You could put the FM presets in order of ascending

frequency. For example put 89.70 into Preset 1, 90.95 into Preset 2, 93.70 into Preset 3, etc. Or you could

assign presets on the basis of how often you listen to them. For example, your favorite station could go into

Preset 1, the next favorite into preset 2, etc.

10

Setting a Station Preset

1

Tune in the FM or DAB station you want to assign to a preset.

3

Press and hold the TUNE control for 3 seconds. The preset

indicator in the upper left corner of the display will light

indicating the station has been stored in the preset.

In this example FM station 104.75 has been assigned to preset 1.

Tuning in a Preset Station

1

Turn the MODE/INFO control to highlight “Preset” in the display.

2

Press the MODE/INFO control. The last preset tuned in is

recalled.

3

Turn the TUNE control to select the station preset you want.

4

Press the TUNE control to select the preset.

Removing One or More Presets

To remove one preset, tune in the preset station as described above.

Press and hold the TUNE control until “Preset Cleared”  ashes in the

display.

If you want to clear all the presets so you can reprogram them, press and hold the TUNE control for 10

seconds until “Presets Empty” appears in the display.

Alarm Clock Features

The Solo XT has two independent alarm settings. Each can have its own type of alarm —wake to tone, wake

to music or both. Both types of alarms start at a low volume level that gently increases. In addition you can

set the alarms for every day, weekdays only or weekends only .

Alarm Setup

1

Press and hold the Alarm 1 or Alarm 2 button for one second to access

the “Alarm Setup” screen shown here.

2

Turn the MODE/INFO control to highlight the item you want to adjust,

then press the control to select it. For example, if you highlight “Alarm

Time” and press the control you’ll see the second display screen with the

Alarm Time highlight box  ashing.

3

Turn either the MODE/INFO or TUNE control to adjust the Alarm Time,

then press the control.

11

The other setting are adjusted the same way.

Active Days: Weekdays/Weekends/7Days – Choose which days you want to use the alarm.

Source: DAB/FM/Preset # – Choose the wake to music source you want. You can select either of the radio

sources or one of the presets you have set.

Vol – Set the volume for wake to music.

After you have completed the alarm setup turn the

MODE/INFO or TUNE control to highlight “Exit” (below

Vol) and press the control. Or just wait a few seconds and the menu will “time out” and store the settings.

Turning Alarms On or O

Press the Alarm 1 or Alarm 2 buttons to turn on the alarm and set the alarm

type. One press selects wake to music . A second press selects wake to tone

. A third press selects both. Press the button a fourth time to cancel the

alarm. When an alarm is turned on you’ll see one or both alarm indicators in

the lower corners of the display showing the alarm time and type.

This shows how the display would look when the Solo XT is turned oﬀ and both alarm are on.

The current time is displayed. Alarm 1 is set for wake to tone at 6:45 AM. Alarm 2 is set for wake to music and tone at

7:15 AM.

How the Alarms Work

Wake To Tone – The alarm tone sounds at a low volume then gradually increases to full volume.

Wake To Music – The radio station you selected is played at the volume level you selected with the Alarm

Setup menu.

Wake To Music and Tone – First, the radio station is played. Then, after 5 minutes the alarm tone begins to

sound.

To turn o the alarm press the POWER/VOLUME button.

The Snooze Feature

If you want to sleep a while longer after the alarm sounds you can use the

Snooze feature. Simply touch the metal rim around the front of the Solo XT.

This will delay the alarm for ten minutes. Each additional touch of the rim

increases the length of the Snooze alarm delay by 5 minutes. The maximum

delay is 60 minutes. The display shows the amount of “snooze time” remaining.

To check the remaining snooze time, touch the

metal trim ring. The display will show the amount of

snooze time remaining. Touching the metal trim ring

again while the snooze time is displayed increases

the snooze time to the next higher step – 10 minutes,

15 minutes, 20 minutes, etc. Each additional touch

increases the snooze time by 5 minutes.

To cancel a “Snooze” time setting press the POWER/

VOLUME

button.

Touch Sensitive Rim

12

Sleep Function

You can set the Solo XT to play a radio station for up to 90 minutes. After the speci ed time the Solo XT shuts

o . You can use the Sleep Function with one of the radio sources or with the Aux input.

1

Use the MODE/INFO control to select the source you want. Set the volume level where you want it.

2

Turn the MODE/INFO control to highlight “Setup Options”, then press the control. The “Setup Options”

menu appears in the display.

3

Turn the MODE/INFO control to highlight “Sleep” then press the control. (The “Sleep” menu selection is

not on the initial “Setup Options” menu. Turn the MODE/INFO control until it appears. See the display

illustrations on page 6.) The highlight box around “O ” will  ash.

4

Turn the MODE/INFO or TUNE control clockwise to set the amount of

time delay you want. You can select from 5 to 90 minutes in 5 minute

increments. Press the control.

The display example to the right shows the Sleep delay set for 20 minutes.

5

Turn the MODE/INFO control to highlight “Exit” and press the control. Or wait a few seconds and the

display will “time out” automatically.

The display will go to its default mode – either source or time display,

depending on what you have chosen. The “S” Sleep icon will appear at the

bottom center of the display.

This display example shows the “S” Sleep icon. The radio is tuned to 104.75, which is

Preset 10. The time is 10:40 PM and Alarm 2 is turned on.

To check the remaining sleep time, touch the metal trim ring. The display will show the amount of sleep time

remaining. Touching the metal trim ring again while the sleep time is displayed decreases the sleep time

to the next lower step – 20 minutes, 15 minutes, 10 minutes, etc. Each additional touch decreases the sleep

time by 5 minutes.

Notes: To cancel the Sleep delay before it has  nished press the Power/Volume button to turn the Solo XT

o .

Audio Controls

Usually the Solo XT will sound best without any adjustments to the audio controls. But Bass and Treble

adjustments are available if you want to adjust the tone balance.

1

Turn the MODE/INFO control to highlight “Setup Options’”. Press the control.

2

Turn the MODE/INFO control to highlight “Audio”. Press the control. (The

“Audio” menu selection is not on the initial “Setup Options” menu. Turn

the MODE/INFO control until it appears. See the display illustrations on

page 6.) You’ll see the display shown to the right.

3

Turn the MODE/INFO control to highlight either “Bass” or “Treble”. Press the

control. The highlight box around the setting number will  ash.

4

Turn the MODE/INFO or TUNE control to adjust the setting. Press the

control to set adjustment. Or wait a few seconds and the menu will “time

out” automatically setting the adjustment.

In this example the Bass is set to –2

and the Treble is set to +1

13

Display Controls

The “Display Setup” menu lets you control what information is shown in the display and how it looks. The two

display examples below show the controls available.

To access the Display Setup menu:

1

Turn the MODE/INFO control to highlight “Setup Options”. Press the

control.

2

Turn the MODE/INFO control to highlight “Display”. Press the control. (The

“Display” menu selection is not on the initial “Setup Options” menu. Turn

the MODE/INFO control until it appears. See the display illustrations on page 6.) You’ll see the display

shown to the right.

3

Turn the MODE/INFO control to highlight the display control you want to adjust then press the control.

Turn the MODE/INFO control until the highlight box moves past the Brightness menu selection to

access the controls in the second screen illustration.

4

Once the item you want adjust is selected, turn the TUNE or MODE/INFO control to change the setting,

then press the control.

The settings on the Display Setup menu are:

Display Info: Genre / Signal Quality (in %) / Compression / Network / Frequency / Date and Time

(Clock) – When using the DAB radio this setting determines what appears in the second line of the display.

(See “The DAB Display” on page 8.) When using the FM radio or the Aux input selecting all the settings except

for “Date and Time (Clock)” makes the display default to show the source. When “Date and Time (Clock)” is

selected the display defaults to the time display.

RDS: On/O – Turns the FM radio RDS (Radio Data System) display on or o .

Brightness: 1-20 – Sets the overall brightness level of the display. Set this so the display is easy to read in a

well lit room.

High Brightness (20) Low Brightness (1)

Note that the display brightness will always adjust automatically with changing light conditions. This

adjustment just sets the overall range of the display brightness.

Contrast: 1-20 – Adjust the di erence between the light and dark parts of the display. This should also be set

in a well lit room in conjunction with the adjustments to the Brightness setting.

High Contrast (20) Low Contrast (1)

14

Resetting To Factory Default

Should you want to return your Solo XT to its “out of the box” con guration, you can use the Factory Default

reset feature. This erases the DAB station list, clears the radio station presets, and returns all other menu

settings to there original state.

Warning: Do not use this feature unless you want to return the Solo XT to its original state. Before using this

feature you might want to make notes about how your radio is con gured.

1

Turn the MODE/INFO control to highlight “Setup Options’”. Press the control.

2

Turn the MODE/INFO control to highlight “Factory Default”. (The “Factory

Default” menu selection is not on the initial “Setup Options” menu. Turn

the MODE/INFO control until it appears. See the display illustrations on

page 6.) You’ll see the display shown to the right.

3

Press the control to return your Solo XT to the factory default state.

Connecting Other Equipment

Connecting Headphones

Connect the headphone plug to the

1

/8-inch jack on the front panel. This turns o the Solo XT internal

speaker. If your headphones have the old-style large

1

/4-inch plug you will need an adapter.

Using Aux Inputs

Other audio equipment, such as an iPod or a portable CD player, can be connected to the Solo XT through

the rear panel Aux input. You will need a cable with a stereo mini plug on both ends. Select the Aux input

using the MODE/INFO control as described in the “Selecting Sources or Setup Options Functions” section of

this manual.

Line Output

You can connect the Solo XT to another component using the

1

/8 -inch Line Output jack.

Security Cable Connection

There is a security cable connection point on the rear of the Solo XT, in the corner above the antenna

connector. This is the same as the connection point found on most laptop computers. Connect a computer

security cable between the Solo XT and a solid anchor point to help prevent theft of your Solo XT.

About Clock Memory

When power to the Solo XT is interrupted a special power component called a “super-cap” will keep the clock

functions active for a period of 24-48 hours. If the Solo XT is without power for a longer period of time you

may need to reset the clock when power is restored.

15

Limited Warranty

Boston Acoustics warrants to the original purchaser of the Horizon Solo XT that it will be free of defects in

materials and workmanship for a period of one year from the date of purchase.

Your responsibilities are to install and use them according to the instructions supplied, to provide safe and

secure transportation to an authorized Boston Acoustics service representative, and to present proof of

purchase in the form of your sales slip when requesting service.

Excluded from this warranty is damage that results from abuse, misuse, improper installation, accidents,

shipping, or repairs/modi cations by anyone other than an authorized Boston Acoustics service

representative.

This warranty is limited to the Boston Acoustics product and does not cover damage to any associated

equipment. This warranty does not cover the cost of removal or reinstallation. This warranty is void if the

serial number has been removed or defaced. This warranty gives you speci c legal rights, and you may also

have other rights which vary from state to state.

If Service Seems Necessary

First, contact the dealer from whom you purchased the product. If that is not possible, write to:

Boston Acoustics, Inc.

300 Jubilee Drive

Peabody, MA 01960 USA

Or contact us via e-mail at:

[email protected]

We will promptly advise you of what action to take. If it is necessary to return your Horizon Solo XT to the

factory, please ship it prepaid. After it has been repaired, we will return it freight prepaid in the United States

and Canada.

For EU Customers Only

This symbol found on the product indicates that the product must not be disposed of with

household waste. Instead, it may be placed in a separate collection facility for electronic

waste or returned to a retailer when purchasing similar product. The producer paid to

recycle this product. Doing this contributes to reuse and recycling, minimizes adverse

e ects on the environment and human health and avoids any  nes for incorrect disposal.

16

¡Advertencia! Para reducir el riesgo de incendio o

de descarga eléctrica, no exponga este aparato a

la lluvia o a la humedad.

Este símbolo que aparece en el aparato indica

que el aparato se debe desechar en un punto

de recogida especial para desechos electrónicos

y que no debe colocarse junto con los residuos

domiciliarios.

E

S

P

A

Ñ

O

L

IMPORTANTES INSTRUCCIONES DE SEGURIDAD

Este símbolo que aparece en el aparato indica

riesgos derivados de voltajes peligrosos.

Este símbolo que aparece en el aparato indica que

el usuario debe leer todas las disposiciones de

seguridad que aparecen en el manual del usuario.

Este símbolo que aparece en el aparato indica la

presencia de una doble aislación.

1. Lea estas instrucciones.

2. Conserve estas instrucciones.

3. Respete todas las advertencias.

4. Siga todas las instrucciones.

5. No utilice este aparato cerca del agua.

6. Limpie el aparato sólo con un trapo seco.

7. No bloquee ninguno de los ori cios de ventilación. Instale

el aparato de acuerdo con las instrucciones del fabricante.

8. No instale el aparato cerca de fuentes de calor tales como

radiadores, rejillas de calefacción, estufas u otros aparatos

que produzcan calor (incluidos ampli cadores).

9. No anule el propósito de seguridad del enchufe

polarizado o de tipo puesta a tierra. Un enchufe

polarizado tiene dos patas, una más ancha que la otra.

Un enchufe de tipo puesta a tierra tiene dos patas más

una tercera pata de puesta a tierra. La pata ancha o la

tercera pata se proveen para su seguridad. Si el enchufe

provisto no se puede utilizar en su tomacorriente,

consulte a un electricista para que reemplace el

tomacorriente obsoleto.

10. Proteja el cable de alimentación para evitar que sea

pisado o quede pinzado, particularmente en los

enchufes, los tomacorrientes y el punto en el cual sale

del aparato.

11. Utilice sólo las conexiones/accesorios especi cados por

el fabricante.

12. Desenchufe este aparato durante las tormentas

eléctricas o cuando no vaya a utilizarlo por un período

de tiempo prolongado.

13. Todo servicio técnico debe ser realizado por personal

cali cado. Se requiere servicio técnico cuando el aparato

ha sido dañado de algún modo, por ejemplo si el cable

de alimentación o el enchufe están dañados, si se ha

vertido líquido o han caído objetos dentro del aparato, si

el aparato ha sido expuesto a la lluvia o a la humedad, si no

funciona normalmente, o si ha sufrido una caída.

14. Mantenga como mínimo una distancia de 2” (50mm)

alrededor de la parte delantera, trasera y laterales del

aparato para asegurar que la ventilación sea su ciente.

La ventilación no se debe obstruir cubriendo los

ori cios de ventilación ni por la presencia de objetos

tales como diarios, manteles, cortinas, etc.. sobre o

alrededor del aparato.

15. No coloque sobre el aparato fuentes de llamas abiertas,

tales como velas encendidas.

16. El aparato no se debe exponer a goteras ni a

salpicaduras. No se deben colocar sobre el aparato

objetos que contengan líquidos, tales como  oreros o

jarrones.

17. Tanto el conector para el cable de alimentación que

se encuentra en la parte trasera del aparato como

el enchufe que se conecta al tomacorriente deben

permanecer accesibles para poder desconectar la

energía eléctrica del aparato.

18. Para desconectar completamente este aparato de

la red de CA, desconecte el enchufe del cable de

alimentación del tomacorriente.

19. El tomacorriente donde enchufa el cable de

alimentación debe permanecer fácilmente accesible.

Usuarios Estadounidenses:

Nota: Este equipo ha sido sometido a pruebas y ha

demostrado cumplir los límites de un dispositivo digital

Clase B, de acuerdo con el apartado 15 de las Normas de

la FCC. Estos límites han sido diseñados para proporcionar

una protección razonable contra interferencias nocivas

en instalaciones residenciales. Este equipo genera, utiliza

y puede emitir energía de radiofrecuencia y, si no se

instala y utiliza de acuerdo con las instrucciones, puede

causar interferencias nocivas a las radiocomunicaciones.

Sin embargo, no hay garantía de que no se producirá

interferencia en una instalación en particular. Si este

equipo provoca interferencias nocivas a la recepción de

radio o televisión, lo cual puede determinarse apagando

y encendiendo el equipo, se aconseja que el usuario

intente corregir la interferencia mediante una o más de las

siguientes medidas:

• Cambie la orientación o la ubicación de la antena

receptora.

• Aumente la separación entre el equipo y el receptor.

• Conecte el equipo en un tomacorriente que esté en un

circuito diferente al cual está conectado el receptor.

• Consulte con el vendedor o con un técnico de radio/TV

experimentado para obtener ayuda.

Usuarios Canadienses:

Este aparato digital clase B cumple con la norma

Canadiense ICES-003.

Este aparato digital clase B cumple con la norma NMB-003

de Canadá.

17

Introducción

Gracias por elegir Boston Acoustics y felicitaciones por la compra de la the Radio DAB de Alta Performance

Horizon Solo XT. Si ya tiene otros productos Boston, la excelente calidad de sonido y facilidad de uso de la

Solo XT no lo sorprenderá. Si es su primer producto Boston, bienvenido – creemos que ha realizado una

excelente elección. La Solo XT es una so sticada radio DAB/FM con alarma dual, entrada auxiliar, salida en

línea (“line out”) y salida para audífonos, todo ello en un exterior de diseño de gran estilo, suave al tacto – y

con características “Play Smart.” Lo invitamos a descubrir todas las características y funciones de su nuevo

sistema de audio. Estamos seguros de que lo disfrutará por muchos años.

Características

• Calidad de sonido sobresaliente a través de un altavoz de 3

1

/2 in. en una cámara acústica con ventilación

• Procesamiento de sonido BassTrac® para lograr bajos satisfactorios a cualquier volumen

• Tres controles intuitivos y fáciles de usar permiten operar todas las funciones de la Solo XT

• Visor grande y de fácil lectura con brillo ajustable que disminuye automáticamente en condiciones de

baja iluminación

• Sintonizador DAM/FM estéreo de alta sensibilidad

• Capacidad para almacenar en memoria 20 emisoras

• Soporta DAB en Banda III y Banda L, lo que permite elegir entre una gran variedad de emisoras digitales

• Incluye antena de gran alcance; también se puede utilizar con una antena externa

• Doble función de alarma; cada una de ellas permite elegir despertador con música y/o alarma de tonos

• Las alarmas aumentan gradualmente de volumen para un despertar más agradable

• Repetición de alarma (función “Snooze”) - la totalidad del borde de aluminio delantero es una barra

sensible al tacto, imposible de no encontrar, que permite activar la función de repetición de alarma

• Función de apagado automático (función “Sleep”) que permite escuchar música hasta 90 minutos antes

que la Solo XT se apague automáticamente

• ¡Hágala suya! Personalice su Solo XT con las grillas opcionales disponibles en bostonacoustic.com/POP

• La radio recuerda la hora programada, las emisoras almacenadas en la memoria y las alarmas con guradas

aunque falte la energía eléctrica

• Conector para audífonos en el panel delantero

• Entrada auxiliar para reproductores de música portátiles

• Fuente de alimentación interna - no requiere voluminosos adaptadores externos

registradas, y el símbolo elíptico de B/A y Play Smart son marcas comerciales de Boston Acoustics, Inc.

18

Desembalaje y preparación de la Horizon Solo XT

Desembale la Horizon Solo XT cuidadosamente. Si observa algún daño que haya ocurrido durante el

transporte, infórmelo inmediatamente a su vendedor y/o servicio de entrega. Conserve la caja y los

materiales de embalaje para uso futuro. Conserve el recibo de compra en un lugar seguro, ya que podría

necesitarlo para los  nes de la garantía.

Dentro de la caja encontrará la Solo XT (con la antena ya colocada) y el cable de alimentación.

Opciones de colocación

Su Horizon Solo XT tendrá un excelente sonido prácticamente en cualquier ubicación que la coloque. Sin

embargo, si coloca la radio cerca de un muro o de una esquina mejorará la respuesta de bajos. Si bloquea el

puerto de bajos provocará una pérdida de rendimiento.

Posición horizontal o vertical

El panel de control de la Solo XT puede rotar, lo que

permite utilizar la radio en posición horizontal o

vertical. Si desea cambiar la orientación de la radio

gire 90º el anillo que rodea el panel de control.

Contenido

Desembalaje y preparación de la Horizon Solo XT 18

Opciones de colocación 18

Posición horizontal o vertical 18

Conexión a la red eléctrica 19

Antena 19

Controles del panel delantero 19

Operaciones de control básicas 20

Encender o apagar la Solo XT 20

Regular el volumen 20

Seleccionar una fuente o una

función programable 20

Acerca de las funciones programables 20

Con gurar el reloj, la hora, la fecha y

otras funciones relacionadas 21

Radio FM 21

Sintonizar una emisora FM 21

Búsqueda de emisoras FM 21

Radio DAB 22

Lista de emisoras DAB 22

Sintonizar una emisora DAB 22

Pantalla correspondiente a la fuente DAB 22

Programación de emisoras DAB 23

Acerca de las emisoras almacenadas

en la memoria 23

Memorizar una emisora 24

Sintonizar una emisora memorizada 24

Borrar una o más emisoras memorizadas 24

Funciones del reloj alarma 24

Con guración de las alarmas 24

Activar o desactivar una alarma 25

Cómo funcionan las alarmas 25

Función de repetición de alarma (“Snooze”) 25

Función de apagado automático (“Sleep”) 26

Controles del sonido 26

Opciones para con gurar la pantalla 27

Reiniciar y regresar a la programación de fábrica 28

Conexión de otros equipos 28

Conexión de audífonos 28

Uso de las entradas auxiliares 28

Salida en línea 28

Conexión de un cable de seguridad 28

Acerca de la memoria del reloj 28

Garantía limitada 29

Si piensa que necesita servicio técnico 29

19

Conexión a la red eléctrica

Simplemente conecte el cable de alimentación a la parte

posterior de la Solo XT y enchufe en un tomacorriente.

Antena

La Horizon Solo XT viene con una antena extensible

conectada a una salida que se encuentra en el panel

posterior.

Nota: Boston Acoustics ha hallado que cuando no se utiliza

la antena provista con el producto, la presencia de señales

fuertes puede interferir con el funcionamiento normal de la

radio.

Controles del panel delantero

Prácticamente todas las funciones de la Horizon Solo XT se operan usando los tres controles que se

encuentran en el panel delantero.

Encendido/Volumen – Controlados mediante la perilla de

mayor tamaño ubicada en la parte central inferior del panel

delantero.

Modo/Info (“Mode/Info”) – Para seleccionar la entrada que

desea utilizar o la función que desea programar.

Sintonizar (“Tune”) – Para sintonizar una nueva emisora.

Estos controles lógicos e intuitivos hacen que la Horizon

Solo XT sea muy fácil de utilizar. El modo de uso es igual

para todas las funciones. Una vez que aprenda a controlar

una de las funciones el resto será muy sencillo. Después que

haya comprendido cómo funcionan los controles es posible

que ya no tenga que consultar este manual nuevamente.

Antena DAB/FM

Entrada CA

Entrada Aux

Salida en línea

20

Operaciones de control básicas

Encender o apagar la Solo XT

Presione el control ENCENDIDO/VOLUMEN que se encuentra en el

centro del panel delantero.

Regular el volumen

Gire la perilla ENCENDIDO/VOLUMEN del panel delantero.

Nota: En las  guras que ilustran los controles –

Una  echa normal indica que se debe presionar y soltar

el botón o control.

Una  echa de doble cabeza indica que se debe presionar

y mantener presionado el botón o control.

Seleccionar una fuente o una función programable

Use el control MODE/INFO para seleccionar la fuente que desea escuchar o para acceder a los menús “DAB

Setup” o “Setup Options” (para programar emisoras DAB o para programar alguna función de la radio,

respectivamente).

1

Gire el control MODE/INFO para visualizar el menú “Mode”

. Seleccione la fuente que desea escuchar o el menú al

cual desea acceder.

2

Presione el control MODE/INFO.

Nota: La pantalla inicial no muestra la selección “Setup

Options” . Para acceder a “Setup Options” desplace el cuadro

de selección más allá de “DAB Setup” .





Esta ﬁ gura muestra la fuente “DAB”

lista para ser seleccionada.

Acerca de las funciones programables

Cuando seleccione la opción “Setup Options” del menú “Mode” verá las funciones programables. Inicialmente

aparecerá la pantalla ilustrada a la izquierda. Gire el control MODE/INFO para mover el cuadro de selección. Si

gira el control MODE/INFO hasta que el cuadro de selección se desplace más allá de la opción “Display” en el

menú aparecerán más opciones, tal como se ilustra en la  gura de la derecha.

Esta pantalla muestra la opción

“Alarm 1“ lista para ser seleccionada.

Esta pantalla muestra la opción

“Audio” lista para ser seleccionada.

En la siguiente sección se describe el procedimiento para programar el reloj. Las demás funciones

programables se describen en secciones posteriores. Una vez que haya aprendido cómo programar una de

las funciones del menú “Mode” el resto será muy sencillo.

Sidan laddas ...

Boston Acoustics Horizon Solo Användarmanual

Denna manual är också lämplig för

Boston Acoustics Horizon Solo Användarmanual

på andra språk

Relaterade papper

Andra dokument