Danfoss CF-RF Room Thermostat Installationsguide

SE

088U0213

Instruction CF-RF Room Thermostat with Infrared Floor Sensor

Instruktion CF-RF Raumthermostat mit Infrarot-Bodensensor

Vejledning til CF-RF-rumtermostat med infrarød gulvsensor

Instructions Thermostat d’ambiance CF-RF avec Capteur au sol infrarouge

Instruction CF-RF rumstermostate med infraröd golvsensor

1VI.UH.R1.80

Produced by Danfoss Floor Heating Hydronics 01.2006

Instruction CF-RF Room Thermostat with InfraRed Floor Sensor

GB

Instruction . . . . . . . . . . . . . . . . . . . . . . . 3

D

Instruktion . . . . . . . . . . . . . . . . . . . . . . 15

DK

Vejledning . . . . . . . . . . . . . . . . . . . . . . 28

F

Instruction . . . . . . . . . . . . . . . . . . . . . . 41

SE

Bruksanvisning . . . . . . . . . . . . . . . . . 54

2

VI.UH.R1.80

Produced by Danfoss Floor Heating Hydronics 01.2006

Instruction CF-RF Room Thermostat with InfraRed Floor Sensor

3VI.UH.R1.80

Produced by Danfoss Floor Heating Hydronics 01.2006

Instruction CF-RF Room Thermostat with InfraRed Floor Sensor

1. Functional Overview . . . . . . . . . . . . . . . . . . . . . . . . 4

2. Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

3. Temperature Settings . . . . . . . . . . . . . . . . . . . . . . . 6

4. Transmission Test . . . . . . . . . . . . . . . . . . . . . . . . . . 10

5. Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

6. Uninstallation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

7. Specications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

8. Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

9. Figures and Illustrations . . . . . . . . . . . . . . . . A1-A2

GB

Index

4

VI.UH.R1.80

Produced by Danfoss Floor Heating Hydronics 01.2006

Instruction CF-RF Room Thermostat with InfraRed Floor Sensor

1. Functional Overview

Front - g. 1

Up/down selector

Push button

Red LED (behind the cover)

InfraRed oor sensor

LED modes

Permanent light ON

No light OFF

Slow ashing Flashes

Fast ashing Flickers

Back - g. 2

Back plate

Back plate lock/unlock (turn 90°)

Screw hole for wall mounting

Battery placement

Screw and wall plug

5VI.UH.R1.80

Produced by Danfoss Floor Heating Hydronics 01.2006

Instruction CF-RF Room Thermostat with InfraRed Floor Sensor

2. Installation

Note:

• To activate batteries in the Room Thermostat,

please remove enclosed strips from the batteries.

• The assignment of the Room Thermostats to the

Master Controller should be within 1½ m distance

Activate Install mode on

Master Controller - g. 1.

• Use the menu selection button to select the

Install mode. Install LED ashes

• Activate Install mode by pressing OK . Install

LED goes ON

Activate Install mode on

Room Thermostat

• Press the push button . LED and icker

during communication

Select output on Master Controller

• All available output LEDs on Master Controller

light up, and the rst of them ashes

• Press output selection button , to select

desired output (ashes) and accept with OK

• All output LEDs go OFF. Selected output

stays ON shortly

6

VI.UH.R1.80

Produced by Danfoss Floor Heating Hydronics 01.2006

Instruction CF-RF Room Thermostat with InfraRed Floor Sensor

Room Thermostat installation status

• Satisfactory - LED goes OFF

• Not satisfactory - LED ashes 5 times

Note: A Room Thermostat can be assigned to sev-

eral outputs if needed by repeating the installation

process.

3. Temperature Settings

Digital Display - g. 1

Set value adjustment

Minimum temperature limitation

Maximum temperature limitation

Lock icon (settings locked from

Remote Controller, CF-RC)

Transmission link icon

Low battery indicator

Alarm icon

Timer icon (time program is active from

Remote Controller, CF-RC)

Room temperature

Floor surface temperature

7VI.UH.R1.80

Produced by Danfoss Floor Heating Hydronics 01.2006

Instruction CF-RF Room Thermostat with InfraRed Floor Sensor

Changing default display temperature

- g. 1.

1. The actual room temperature is shown in the

display as default

2. To change default display from actual room

temperature to actual oor surface tempera-

ture, press and hold the push button

until SET MAX is shown in the display

3. Press the button shortly and repeatedly

until

or is ashing in the display

4. Press the up/down selector to select the

new default display temperature:

Room temperature

Floor surface temperature

Setting of room temperature

1. Make sure actual room temperature is shown

in the display

2. Press the up/down selector to set the

desired room temperature value. SET is shown

in the display

3. When releasing the up/down selector the

display returns to actual temperature

Note: The thermostat regulates the oor heating

system according to room temperature set point,

within the maximum and minimum limitations

dened for the oor surface temperature

8

VI.UH.R1.80

Produced by Danfoss Floor Heating Hydronics 01.2006

Instruction CF-RF Room Thermostat with InfraRed Floor Sensor

Room temperature limitation

1. Make sure actual room temperature is shown

in the display

2. Press the push button until SET MAX is

shown in the display

3. Press the up/down selector to set the

maximum room temperature limitation

4. Press the push button shortly, SET MIN is

shown in the display

5. Press the up/down selector to set the mini-

mum room temperature limitation

6. Press the push button shortly and the

actual oor surface temperature is shown in

the display

Floor surface temperature limitation

1. Ensure actual oor surface temperature is

shown in the display illustrated by

2. Press and hold the push button until SET

MAX is also shown in the display

3. Press the up/down selector to set the

maximum oor surface temperature limitation

4. Press the push button shortly, SET MIN is

also shown in the display

5. Press the up/down selector to set the mini-

mum oor surface temperature limitation

9VI.UH.R1.80

Produced by Danfoss Floor Heating Hydronics 01.2006

Instruction CF-RF Room Thermostat with InfraRed Floor Sensor

IMPORTANT!

As heat emission from the oor may vary slightly

depending on oor covering - and thereby cause

inaccurate temperature measurement - it may be

necessary to adjust the setting of max. and min.

oor surface temperatures accordingly.

! It is important always to follow recommendations

from the oor manufacturer regarding max. oor

surface temperature.

! It is recommended always to include mixing shunt

for oor heating circuits in order to ensure optimal

ow temperature. - In addition to minimised energy

consumption, correct setting of the ow tempera-

ture will eliminate the risk of excessive heat transfer

to the oor.

10

VI.UH.R1.80

Produced by Danfoss Floor Heating Hydronics 01.2006

Instruction CF-RF Room Thermostat with InfraRed Floor Sensor

4. Transmission Test

Initiate transmission test on Room

Thermostat - g. 1

• Press the push button

• LED goes ON

Link test is satisfactory

• LED goes OFF

Link test is unsatisfactory

• LED ashes 5 times

No link connection to Room Thermostat

• Try to relocate Room Thermostat in the room

• Or install Repeater Unit (CF-RU) and locate

between Master Controller and Room

Thermostat

Note: Master Controller output LED(s) connected

to the Room thermostat, ash(es) during link test

11VI.UH.R1.80

Produced by Danfoss Floor Heating Hydronics 01.2006

Instruction CF-RF Room Thermostat with InfraRed Floor Sensor

5. Mounting

Placing the Room Thermostat - g. 3

• The Room Thermostat should be placed in

accordance with g. 3

IMPORTANT!

Wherever possible, the room thermostat should

be installed at a place where the eect of sunlight,

strong articial light (e.g. halogen spotlight),

draught, other heat-emitting equipment (e.g. TVs)

etc. is avoided.

! Please note that no furniture, rugs etc. should be

permanently placed within the area of the InfraRed

Floor Sensor as shown in g. 3.

Mounting - g. 2

1. Mount the back plate with the two screws

and wall plugs via the screw holes in the

back plate

2. Slide thermostat into place on the back plate

3. If desired lock the thermostat to the back plate

with Allen key (turn 90°)

12

VI.UH.R1.80

Produced by Danfoss Floor Heating Hydronics 01.2006

Instruction CF-RF Room Thermostat with InfraRed Floor Sensor

6. Uninstallation

Activate Uninstall mode on Master

Controller - g. 1

• Use the Menu selection button to choose

the Uninstall menu. Uninstall LED ashes

• Activate Uninstall mode by pressing OK .

Uninstall LED goes ON

Deselect output on Master Controller

• Select output to be removed by output selec-

tion button

• Remove ashing output with OK

13VI.UH.R1.80

Produced by Danfoss Floor Heating Hydronics 01.2006

Instruction CF-RF Room Thermostat with InfraRed Floor Sensor

Temperature setting

range

5-35°C

Transmission frequency 868.42MHz

Transmission range in

normal buildings (up to)

30m

Transmission power < 1mW

Battery Alkaline 2xAA, 1.5V

Battery lifetime

(up to)

1-3 years

Ambient temperature 0-50°C

IP class 21

Sensor accuracy +/- 1°C

Sensor emission coef-

cient

0.9

7. Specications

14

VI.UH.R1.80

Produced by Danfoss Floor Heating Hydronics 01.2006

Instruction CF-RF Room Thermostat with InfraRed Floor Sensor

Error Indication Possible Cause

The LED, and

ashes every 5th minute

Low battery

The LED, and

ashes

Critical low battery

The LED, , and

ashes

Critical low battery -

transmission has stopped

The LED, and

ashes 5 times

Installation/link Test is

unsatisfactory

E03 and

Actuator error on output

(CF-MC)

E05 and

Room temperature below

5ºC

8. Troubleshooting

15VI.UH.R1.80

Hergestellt von Danfoss Floor Heating Hydronics 01.2006

Instruktion CF-RF Raumthermostat mit Infrarot-Oberächenfühler

1. Funktionsübersicht ................................................ 16

2. Installation ................................................................. 17

3. Temperatureinstellungen ....................................18

4. Funk - Verbindungstest .........................................23

5. Montage ...................................................................... 24

6. Deinstallation ........................................................... 25

7. Technische Daten .....................................................26

8. Fehlersuche ................................................................27

9. Bilder und Zeichnungen .............................. A1-A2

D

Inhaltsverzeichnis

Instruktion CF-RF Raumthermostat mit Infrarot-Oberächenfühler

16

VI.UH.R1.80

Hergestellt von Danfoss Floor Heating Hydronics 01.2006

1. Funktionsübersicht

Vorderseite - Fig. 1

Freie Temperaturwahl

Druckknopf

Rote LED (hinter der Abdeckung)

Infrarot-Oberächenfühler

LED Anzeige

Dauerlicht EIN

Leuchtet nicht AUS

Blinkt langsam Blinkt

Blinkt schnell Flackert

Rückseite - Fig. 2

Hintere Abdeckung

Hintere Abdeckung verriegeln / entriegeln

(um 90° drehen)

Schraubenloch für Wandmontage

Batteriepositionierung

Schraube und Dübel

17VI.UH.R1.80

Hergestellt von Danfoss Floor Heating Hydronics 01.2006

Instruktion CF-RF Raumthermostat mit Infrarot-Oberächenfühler

2. Installation

Anmerkung:

• Zum Aktivieren der Batterien im Raumthermosta-

ten entfernen Sie bitte den Trennstreifen von den

Batterien.

• Die Anmeldung des Raumthermostaten muss

innerhalb von 1,5 m vom Hauptregler erfolgen.

Aktivieren Sie den Installationsmo-

dus am Hauptregler – Fig. 1

• Verwenden Sie die Taste zur Menüauswahl ,

um den Installationsmodus zu wählen.

Die Installations-LED blinkt.

• Aktivieren Sie den Installationsmodus, indem

Sie auf OK drücken . Die Installations-LED

wechselt zu „EIN“.

Aktivieren Sie den Installations-

modus am Raumthermostaten

• Betätigen Sie den Druckknopf . Die LED

und ackern während der Kommunikation.

Wählen Sie den Ausgang am Haupt-

regler

• Alle verfügbaren Ausgangs-LED am Hauptregler

leuchten, und die erste LED blinkt.

Instruktion CF-RF Raumthermostat mit Infrarot-Oberächenfühler

18

VI.UH.R1.80

Hergestellt von Danfoss Floor Heating Hydronics 01.2006

• Betätigen Sie die Taste zur Ausgangswahl

wählen Sie den gewünschten Ausgang (blinkt),

und bestätigen Sie mit OK .

• Alle Ausgangs-LED wechseln zu „AUS“.

Der gewählte Ausgang wechselt kurz zu „EIN“.

Installationsstatus des Raumthermo-

staten

• Wenn OK - LED wechselt zu „AUS“.

• Wenn nicht OK - LED blinkt 5 Mal.

Anmerkung: Ein Raumthermostat kann bei Bedarf

mehreren Ausgängen (Stellantrieben) zugeord-

net werden.

3. Temperatureinstellungen

Digitalanzeige - Fig. 1.

Temperatureinstellung

Min. Temperaturbegrenzung

Max. Temperaturbegrenzung

Symbol Sperre (Einstellungen werden

über die Fernbedienung CF-RC gesperrt)

19VI.UH.R1.80

Hergestellt von Danfoss Floor Heating Hydronics 01.2006

Instruktion CF-RF Raumthermostat mit Infrarot-Oberächenfühler

Symbol Funk-Sendeverbindung

Anzeige Batterieladezustand niedrig

Symbol Alarm

Symbol (Zeit- und Zonenkontrolle,

über die Fernbedienung CF- RC

eingestellt)

Raumtemperatur

Bodenoberächentemperatur

Änderung der voreingestellten Tem-

peratur auf dem Display - Fig. 1.

1. In der Grundeinstellung wird auf dem Display

die tatsächliche Raumtemperatur angezeigt.

2. Um diese Grundeinstellung von der Raum-

temperatur auf die Bodenoberächentempe-

ratur zu ändern, drücken Sie Druckknopf

so lange, bis EINST MAX auf dem Display

erscheint.

3. Kurz und wiederholt auf den Druckknopf

drücken, bis oder auf dem Display

blinkt.

4. Den hoch/niedrig Druckknopf betätigen,

um die neue voreingestellte Bildschirm-

temperatur zu wählen:

Raumtemperatur

Bodenoberächentemperatur

Sidan laddas ...

Danfoss CF-RF Room Thermostat Installationsguide

Danfoss CF-RF Room Thermostat Installationsguide

på andra språk

Relaterade papper

Andra dokument