Cisco Systems 1800 Användarmanual

Typ
Användarmanual

Denna manual är också lämplig för

Americas Headquarters:
© 2007 Cisco Systems, Inc. All rights reserved.
Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA
Regulatory Compliance and Safety Information
for Cisco 1800 Integrated Services
Routers (Fixed)
This publication provides international regulatory compliance and safety information for Cisco 1800
Integrated Services Routers (fixed configuration). The model numbers are printed on the bottom
homologation labels with the approval logos and certification numbers.
Use this publication with other documentation that is available for your router.
This document contains the following sections:
Safety, page 1
Electromagnetic Compatibility, page 4
Telecommunications, page 8
Declaration of Conformity Statements, page 13
California Perchlorate Contamination Prevention Act—Title 22, California Code of Regulations,
Chapter 33, page 13
Translated Safety Warnings, page 13
Obtaining Documentation, Obtaining Support, and Security Guidelines, page 73
Safety
This section describes safety conditions and operating conditions for Cisco 1800 fixed configuration
routers. It contains the following:
Agency Approvals and Standards
Restricted Area
Lithium Backup Battery
Operating Conditions for Canada
2
Regulatory Compliance and Safety Information for Cisco 1800 Integrated Services Routers (Fixed)
OL-10256-02
Safety
Operating Conditions for Australia and the European Community
Operating Conditions for the United Kingdom
Warning
This equipment will be inoperable when mains power fails.
Statement 198
Warning
High leakage current—permanent earth connection essential before making Telecommunication
Network Connection.
Statement 343
Warning
To avoid electric shock, do not connect safety extra-low voltage (SELV) circuits to telephone-network
voltage (TNV) circuits. LAN ports contain SELV circuits, and WAN ports contain TNV circuits. Some
LAN and WAN ports both use RJ-45 connectors. Use caution when connecting cables.
Statement 1021
Warning
Never touch uninsulated telephone wires or terminals unless the telephone line has been
disconnected at the network interface.
Statement 1037
Warning
Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote
risk of electric shock from lightning.
Statement 1038
Warning
For connections outside the building where the equipment is installed, the following ports must be
connected through an approved network termination unit with integral circuit protection.
10/100/1000 Ethernet
Statement 1044
Warning
Voltages that present a shock hazard may exist on Power over Ethernet (PoE) circuits if
interconnections are made using uninsulated exposed metal contacts, conductors, or terminals.
Avoid using such interconnection methods, unless the exposed metal parts are located within a
restricted access location and users and service people who are authorized within the restricted
access location are made aware of the hazard. A restricted access area can be accessed only
through the use of a special tool, lock and key or other means of security.
Statement 1072
Warning
No user-serviceable parts inside. Do not open.
Statement 1073
Agency Approvals and Standards
This section lists the following agency approvals and standards for safety:
CSA Certified to UL 60950 and CSA 22.2 No. 60950
ACA to AS/NZS 60950
CB Certificate/Test Report to IEC 60950-1, edition 1 (2001) with all country deviations, as well as
to EN 60950-1
3
Regulatory Compliance and Safety Information for Cisco 1800 Integrated Services Routers (Fixed)
OL-10256-02
Safety
Restricted Area
The following warning is applicable only in Scandinavian countries.
Warning
This unit is intended for installation in restricted access areas. A restricted access area can be
accessed only through the use of a special tool, lock and key, or other means of security.
Statement 1017
Lithium Backup Battery
Cisco 1800 fixed configuration routers have an internal real-time clock with battery backup. The backup
battery is a socketed lithium battery. This battery lasts the life of the router under the operating
environmental conditions specified for the router, and is not field-replaceable.
Note Although the lithium battery is not intended to be field-replaceable, the safety agencies require that the
following warning be included in this document.
Warning
There is the danger of explosion if the battery is replaced incorrectly. Replace the battery only with
the same or equivalent type recommended by the manufacturer. Dispose of used batteries according
to the manufacturer’s instructions.
Statement 1015
Operating Conditions for Canada
In addition to the warnings and safety guidelines listed in the “Translated Safety Warnings” section on
page 13 in this document, the following operating conditions apply to routers used in Canada:
The Canadian Department of Communications label identifies certified equipment. This certification
means that the equipment meets certain telecommunications network protective operational and safety
requirements. The Department does not guarantee that the equipment will operate to the
user’s satisfaction.
Before installing the equipment, users should ensure that it is permissible to be connected to the facilities
of the local telecommunications company. The equipment must also be installed using an acceptable
method of connection. In some cases, the company’s inside wiring associated with a single line
individual service may be extended by means of a certified connector assembly (telephone extension
cord). The customer should be aware that compliance with the above conditions may not prevent
degradation of service in some situations.
Repairs to certified equipment should be made by an authorized Canadian maintenance facility
designated by the supplier. Any repairs or alterations made by the user to this equipment, or equipment
malfunctions, may give the telecommunications company cause to request the user to disconnect the
equipment.
Users should ensure for their own protection that the electrical ground connections of the power utility,
telephone lines and internal metallic water pipe system, if present, are connected together. This
precaution may be particularly important in rural areas.
4
Regulatory Compliance and Safety Information for Cisco 1800 Integrated Services Routers (Fixed)
OL-10256-02
Electromagnetic Compatibility
Warning
Only trained and qualified personnel should be allowed to install, replace, or service this equipment.
Statement 1030
Operating Conditions for Australia and the European Community
The warnings and safety guidelines listed in the section “Translated Safety Warnings” section on page 13
in this document apply to routers used in Australia and the European Community.
Operating Conditions for the United Kingdom
In addition to the warnings and safety guidelines listed in the section “Translated Safety Warnings”
section on page 13 in this document, the following warnings and safety guidelines apply to routers used
in the United Kingdom:
The router is designed to meet the requirements of interim CTR3 for Basic Rate Access.
Interconnection directly, or by way of other apparatus, of ports marked:
Safety Warning—See instructions for use
with ports marked or not so marked may produce hazardous conditions on the network, and that
advice should be obtained from a competent engineer before such a connection is made.
The BRI connector must be hardwired permanently to the S-reference connection point by using a
connect one-time-only, nonremovable plug (RJ-45 with the latch tab removed).
The ports marked “10BaseT, “Console,” and “ISDN” have a safety warning applied to them as
follows:
“These ports do not provide isolation sufficient to satisfy the requirement of EN41003; apparatus
connected to these ports should either have been approved to EN41003 or have previously been
evaluated against B5E301 British Telecommunications plc (Post Office) Technical Guides 2 or 26
and given permission to attach; any other usage will invalidate any approval given to this apparatus.
Other usage will invalidate any approval given to this apparatus if as a result it ceases to comply with
EN41003:1993.
This apparatus must be connected to a main socket outlet with a protective earth contact.
Connection of power supply: The router is intended for use when supplied with power from a supply
providing 100 to 240 VAC, 50 to 60 Hz, up to 0.5A.
Electromagnetic Compatibility
This section describes electromagnetic compatibility (EMC) compliance conditions for the
Cisco 1800 fixed configuration routers. It contains the following:
Country Approvals and Standards
CISPR 22 Class A Warning
FCC Part 15 Notice
Class A Notice for Canada
Statement 191—VCCI Class A Warning for Japan
5
Regulatory Compliance and Safety Information for Cisco 1800 Integrated Services Routers (Fixed)
OL-10256-02
Electromagnetic Compatibility
Statement 371—Power Cable and AC Adapter for Japan
Statement 256—Class A Warning for Hungary
Statement 294—Class A Warning for Korea
Country Approvals and Standards
This section lists the following country approvals and standards for EMC:
Emissions for the Cisco 1800 fixed configuration routers—47CFR15 Class A (FCC); CISPR22
Class A; EN55022 Class A; AS/NZS 3548 Class A (ACA); ICES-003 Class A (Industry Canada);
V-3 Class A (VCCI); EN61000-3-2; EN61000-3-3; EN300386 Class A; KN 22 (Korea)
Immunity for Cisco 1800 fixed configuration routers—EN55024, EN50082-1, and EN61000-6-1
(including EN 61000-4-2 Electrostatic Discharge; EN 61000-4-3 Radiated Susceptibility; EN
61000-4-4 Electrical Fast Transients; EN 61000-4-5 Power & Signal Line Surges; EN 61000-4-6
Injected RF Swept Immunity; EN61000-4-11 Voltage Dips + Sags); EN300386
CISPR 22 Class A Warning
Warning
This is a class A product. In a domestic environment this product may cause radio interference in
which case the user may be required to take adequate measures.
FCC Part 15 Notice
Cisco 1800 fixed configuration routers comply with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
1. These devices may not cause harmful interference.
2. These devices must accept any interference received, including interference that may cause
undesired operation.
Modifying the equipment without authorization from Cisco may result in the equipment no longer
complying with FCC requirements for Class A or Class B digital devices. In that event, your right to use
the equipment may be limited by FCC regulations, and you may be required to correct any interference
to radio or television communications at your own expense.
Note This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
6
Regulatory Compliance and Safety Information for Cisco 1800 Integrated Services Routers (Fixed)
OL-10256-02
Electromagnetic Compatibility
Class A Notice for Canada
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.
Equipment Attachment Limitations
The Industry Canada label identifies certified equipment. This certification means that the equipment
meets certain telecommunications network protective, operational, and safety requirements as
prescribed in the appropriate Terminal Equipment Technical Requirement Documents. The Department
does not guarantee the equipment will operate to the user’s satisfaction.
Note This equipment meets the applicable Industry Canada Terminal Equipment Technical Specifications.
This is confirmed by the registration number. The abbreviation, IC, before the registration number
signifies that registration was performed based on a Declaration of Conformity indicating that Industry
Canada technical specifications were met. It does not imply that Industry Canada approved the
equipment.
Before installing this equipment, users should ensure that it is permissible to be connected to the
facilities of the local telecommunications company. The equipment must also be installed using an
acceptable method of connection. In some cases, the company’s inside wiring associated with a
single-line individual service may be extended by means of a certified connector assembly (telephone
extension cord). The customer should be aware that compliance with the above conditions might not
prevent degradation of service in some situations.
Repairs to certified equipment should be made by an authorized Canadian maintenance facility
designated by the supplier. Any repairs or alterations made by the user to this equipment, or equipment
malfunctions, may give the telecommunications company cause to request the user to disconnect the
equipment.
Users should ensure for their own protection that the electrical ground connections of the power utility,
telephone lines, and internal metallic water pipe system, if present, are connected together. This
precaution may be particularly important in rural areas.
Caution Users should not attempt to make such connections themselves, but should contact the appropriate
electrical inspection authority, or electrician, as appropriate.
7
Regulatory Compliance and Safety Information for Cisco 1800 Integrated Services Routers (Fixed)
OL-10256-02
Electromagnetic Compatibility
Statement 191—VCCI Class A Warning for Japan
Statement 371—Power Cable and AC Adapter for Japan
When installing the product, please use the provided or designated connection cables/power cables/AC
adaptors. Using any other cables/adaptors could cause a malfunction or a fire. Electrical Appliance and
Material Safety Law prohibits the use of UL-certified cables (that have the “UL” shown on the code) for
any other electrical devices than products designated by CISCO. The use of cables that are certified by
Electrical Appliance and Material Safety Law (that have “PSE” shown on the code) is not limited to
CISCO-designated products.
Statement 256—Class A Warning for Hungary
Warning
This is a Class A product based on the standard of the Voluntary Control Council for Interference by
Information Technology Equipment (VCCI). If this equipment is used in a domestic environment, radio
disturbance may arise. When such trouble occurs, the user may be required to take corrective
actions.
Warning
This equipment is a class A product and should be used and installed properly according to the
Hungarian EMC Class A requirements (MSZEN55022). Class A equipment is designed for typical
commercial establishments for which special conditions of installation and protection distance are
used.
8
Regulatory Compliance and Safety Information for Cisco 1800 Integrated Services Routers (Fixed)
OL-10256-02
Telecommunications
Statement 294—Class A Warning for Korea
Telecommunications
This section describes telecommunications compliance conditions for Cisco 1800 fixed configuration
routers. It contains the following:
Country Approvals and Standards
FCC Part 68 Notice
Universal Service Order Code Jacks
Router Port Approvals—FCC and Industry Canada
Declarations of Conformity to R&TTE Directive 1999/5/EEC for the European Community,
Switzerland, Norway, Iceland, and Liechtenstein
Country Approvals and Standards
This section lists the following agency approvals and standards for Telecommunications:
USA—TIA-968-A, TI.TRQ.6
Canada—CS-03
European Union—RTTE Directive 5/99
Argentina—CTR 21, TBR 21
Australia—AS/ACIF-S002, AS/ACIF-S003, AS/ACIF-S016, AS/ACIF-S031, AS/ACIF-S038,
AS/ACIF-S043, ACIF-C559
Brazil—225-540-784, 225-540-788, CTR3, 225-100-717 Edition 3, NET 001/92 1990
ChinaITU-G.992.1, ITU-G.991.2, CTR3, ITU I.431 1993
Hong Kong—HKTA-2011, HKTA-2013, HKTA-2014, HKTA-2017, HKTA-2033
India—I-DCA-18-2, IR-I/TCP-01/02, IR-I/PRI-01/02
Israel—TIA-968-A accepted, TBR21
JapanTechnical condition (DoC acceptance in process)
KoreaTIA-968-A/RRL 2005-96
Warning
This is a Class A Device and is registered for EMC requirements for industrial use. The seller or
buyer should be aware of this. If this type was sold or purchased by mistake, it should be replaced
with a residential-use type.
9
Regulatory Compliance and Safety Information for Cisco 1800 Integrated Services Routers (Fixed)
OL-10256-02
Telecommunications
Mexico—TIA-968-A accepted
New Zealand—PTC-217, PTC-220, PTC 270/272, CTR3, ACA 016, ACIF S016
Singapore—IDA TS ADSL1 Issue 1, IDA TS ADSL 2, IDA TS HDSL, IDA TS ISDN 1 Issue 1 1999,
IDA TS ISDN 3 Issue 1 1999, IDA TS PSTN 1 Issue 4, IDA TS PSTN 1 Issue 4, IDA TS PSTN 1 Issue 4
South Africa—DPTE-TE-001, TIA-968-A accepted
Taiwan—PSTN01, TIA-968-A accepted
FCC Part 68 Notice
This equipment complies with Part 68 of the FCC rules. On the bottom of the chassis is a label that
contains, among other information, the FCC registration number and ringer equivalence number (REN)
for this equipment. If requested, this information must be provided to the telephone company.
If this equipment causes harm to the telephone network, the telephone company will notify you in
advance that temporary discontinuance of service may be required. If advance notice is not practical, the
telephone company will notify the customer as soon as possible. Also, you will be advised of your right
to file a complaint with the FCC if you believe it is necessary.
The telephone company may make changes in its facilities, equipment, operation, or procedures that
could affect the operation of this equipment. If this happens, the telephone company will provide
advance notice in order for you to make the necessary modifications to maintain uninterrupted service.
Normally, this equipment will be used in conjunction with FCC registered equipment that limits the
Encoded Analog Content that provides the required Billing Protection. If the connected equipment is not
of this type, an affidavit must be supplied to the telephone company where the network connection is to
be made. The affidavit is to be notarized, and is to be filed at least ten days before the initial connection.
The facility interface and service order codes are shown in Table 1.
Table 1 Cisco 1800 Fixed Configuration Routers Facility Interface and Service Order Codes
Interface Type
Facility Interface Code
(FIC)
Service Order Code
(SOC) Jack Type (USOC)
ADSL Metallic RJ-11C
SHDSL Metallic RJ-11C
RJ-14C
BRI - S/T 02IS5 6.0N RJ-49C via NT1
BRI-U 02IS5 6.0N RJ-49
T1 data 04DU9-BN
04DU9-DN
04DU9-1KN
04DU9-1SN
6.0N RJ-48C
T1 voice 04DU9-BN
04DU9-DN
04DU9-1KN
04DU9-1SN,
04DU9-1ZN
6.0Y RJ-48C
10
Regulatory Compliance and Safety Information for Cisco 1800 Integrated Services Routers (Fixed)
OL-10256-02
Telecommunications
Universal Service Order Code Jacks
Table 2 lists the universal service order code (USOC) jacks used by Cisco 1800 fixed configuration
routers.
FXO1 02LS2
02GS2
—RJ-11C
RJ-21X
CAMA1 02RV2-0 — RJ-11C
RJ-21X
DID (Reverse battery) 02RV2-T 9.0F (AS.2) RJ-11C
RJ-21X
E&M tie trunk TL11E
TL12E
TL31E
TL32E
9.0F RJ-2EX
RJ-2FX
RJ-2GX
RJ-2HX
Analog modem1 RJ-11C
DSU 56K 04DU5-24
04DU5-48
04DU5-96
04DU5-19
04DU5-38
04DU5-56
04DU5-64
04DU5-56B
6.0F RJ-48S
Table 1 Cisco 1800 Fixed Configuration Routers Facility Interface and Service Order Codes
Interface Type
Facility Interface Code
(FIC)
Service Order Code
(SOC) Jack Type (USOC)
Table 2 USOC Jacks for Cisco 1800 Routers and WAN Interface Cards
Cisco Product Number Facility Interface Code Service Order Code Jack Type
Cisco 1800 02IS5 6.0N CB-1D
Cisco 1800 02DE2 7.0Y RJ-11
Cisco 1800 02LS2 9.0Y RJ-11
WIC-1B-S/T-V3 02IS5 6.0N RJ-48C
WIC-1B-U-V2 02IS5 6.0N RJ-49C
WIC-1DSU-T1-V2 04DU9-BN/DN 6.0N RJ-48C
WIC-1DSU-56K4 04DU5-56 6.0N R3-48S
WIC-1ADSL Metallic 6.0N RJ-11
WIC-1ADSL-DG Metallic 6.0N RJ-11
11
Regulatory Compliance and Safety Information for Cisco 1800 Integrated Services Routers (Fixed)
OL-10256-02
Telecommunications
Router Port Approvals—FCC and Industry Canada
Table 3 lists the FCC and Industry Canada approvals for the router ports.
Declarations of Conformity to R&TTE Directive 1999/5/EEC for the European
Community, Switzerland, Norway, Iceland, and Liechtenstein
WIC-1ADSL-I-DG Metallic 6.0N RJ-11
WIC-1SHDSL Metallic 6.0N RJ-11
WIC-1AM 02LS2 7.0Y RJ-11
WIC-2AM 02LS2 7.0Y RJ-11
VWIC-1MFT-T1 04DU9-BN/DN 6.0N RJ-48C
VWIC-2MFT-T1 04DU9-BN/DN 6.0N RJ-48C
VWIC-2MFT-T1-DI 04DU9-BN/DN 6.0N RJ-48C
VWIC-1MFT-E1 N/A N/A RJ-48
VWIC-1MFT-G703 N/A N/A RJ-48
VWIC-2MFT-E1 N/A N/A RJ-48
VWIC-2MFT-E1-DI N/A N/A RJ-48
VWIC-2MFT-G703 N/A N/A RJ-48
Table 2 USOC Jacks for Cisco 1800 Routers and WAN Interface Cards (continued)
Cisco Product Number Facility Interface Code Service Order Code Jack Type
Table 3 Router Port Approvals—FCC and Industry Canada
Cisco Product Number Port ACTA
1
Product ID
1. Administrative Council for Terminal Attachments
Industry Canada
Approval Number
Cisco 1800 Chassis US:5B1IS01B0143 IC:2461B-0235
Cisco 1861 Chassis US:5B1IS01B0225 IC:2461B-0407
English:
This equipment is in compliance with the essential requirements and other relevant provisions of
Directive 1999/5/EC.
[Bulgarian]:
[Czech]:
Dansk
[Danish]:
Dette udstyr er i overensstemmelse med de væsentlige krav og andre relevante bestemmelser i
Direktiv 1999/5/EF.
12
Regulatory Compliance and Safety Information for Cisco 1800 Integrated Services Routers (Fixed)
OL-10256-02
Telecommunications
Deutsch
[German]:
Dieses Gerät entspricht den grundlegenden Anforderungen und den weiteren entsprechenden
Vorgaben der Richtlinie 1999/5/EU.
Eesti
[Estonian]:
See seade vastab direktiivi 1999/5/EÜ olulistele nõuetele ja teistele asjakohastele sätetele.
Español
[Spanish]:
Este equipo cumple con los requisitos esenciales asi como con otras disposiciones de la Directiva
1999/5/CE.
[Greek]:
Français
[French]:
Cet appareil est conforme aux exigences essentielles et aux autres dispositions pertinentes de la
Directive 1999/5/EC.
Íslenska
[Icelandic]:
Þetta tæki er samkvæmt grunnkröfum og öðrum viðeigandi ákvæðum Tilskipunar 1999/5/EC.
Italiano
[Italian]:
Questo apparato é conforme ai requisiti essenziali ed agli altri principi sanciti dalla Direttiva
1999/5/CE.
Latviski
[Latvian]:
[Lithuanian]:
Nederlands
[Dutch]:
Dit apparaat voldoet aan de essentiele eisen en andere van toepassing zijnde bepalingen van de
Richtlijn 1999/5/EC.
Malti
[Maltese]:
Magyar
[Hungarian]:
Norsk
[Norwegian]:
Dette utstyret er i samsvar med de grunnleggende krav og andre relevante bestemmelser i
EU-direktiv 1999/5/EF.
Polski
[Polish]:
Português
[Portuguese]:
Este equipamento está em conformidade com os requisitos essenciais e outras provisões relevantes
da Directiva 1999/5/EC.
[Romanian]:
Acest echipament este in conformitate cu cerintele esentiale si cu alte prevederi relevante ale
Directivei 1999/5/EC.
Slovensko
[Slovenian]:
Ta naprava je skladna z bistvenimi zahtevami in ostalimi relevantnimi pogoji Direktive 1999/5/EC.
Slovensky
[Slovak]:
Toto zariadenie je v zhode so základnými požiadavkami a inými príslušnými nariadeniami direktív:
1999/5/EC.
13
Regulatory Compliance and Safety Information for Cisco 1800 Integrated Services Routers (Fixed)
OL-10256-02
Declaration of Conformity Statements
Declaration of Conformity Statements
The Declaration of Conformity statements for this product can be found at the following URL:
http://www.ciscofax.com
Note If you still have questions regarding the compliance of these products or you cannot find the information
you are looking for, please send an e-email request to [email protected].
California Perchlorate Contamination Prevention
Act
Title 22, California Code of Regulations, Chapter 33
The battery inside this product might contain perchlorate, a known hazardous substance, so special
handling and disposal of this product might be necessary. For more information about perchlorate
and best management practices for perchlorate-containing substances, see
http://www.dtsc.ca.gov/HazardousWaste/Perchlorate/index.cfm.
Translated Safety Warnings
This sections contains the translations of the following warning statements that appear in the hardware
installation documentation and quick start guide for this router:
Statement 1071—Warning Definition, page 15
Statement 1—Power Disconnection Warning, page 20
Statement 23—ISDN Connection Warning, page 21
Statement 43—Jewelry Removal Warning, page 23
Statement 94—Wrist Strap Warning, page 24
Statement 198—Power Failure Warning, page 26
Statement 248—Unit Mounting Warning, page 26
Statement 343—Before Making Telecommunication Network Connection, page 27
Statement 1001—Work During Lightning Activity, page 28
Statement 1004—Installation Instructions, page 29
Statement 1005—Circuit Breaker, page 30
Statement 1006—Chassis Warning for Rack-Mounting and Servicing, page 31
Suomi
[Finnish]:
Svenska
[Swedish]:
14
Regulatory Compliance and Safety Information for Cisco 1800 Integrated Services Routers (Fixed)
OL-10256-02
Translated Safety Warnings
Statement 1007—TN and IT Power Systems, page 37
Statement 1015—Battery Handling, page 37
Statement 1017—Restricted Area, page 39
Statement 1018—Supply Circuit, page 41
Statement 1021—SELV Circuit, page 43
Statement 1021—SELV Circuit, page 43
Statement 1024—Ground Conductor, page 45
Statement 1026—WAN Port Static Shock, page 47
Statement 1028—More Than One Power Supply, page 48
Statement 1029—Blank Faceplates and Cover Panels, page 50
Statement 1030—Equipment Installation, page 53
Statement 1035—Proximity to Water, page 55
Statement 1036—Telephone Jacks in Wet Locations, page 56
Statement 1037—Uninsulated Wires or Terminals, page 57
Statement 1038—Telephone Use During an Electrical Storm, page 58
Statement 1039—Telephone Use by Gas Leak, page 59
Statement 1040—Product Disposal, page 59
Statement 1041—Disconnecting Telephone-Network Cables, page 61
Statement 1043—Installation Hazard, page 62
Statement 1044—Port Connections, page 64
Statement 1046—Installing or Replacing the Unit, page 66
Statement 1047—Overheating Prevention, page 67
Statement 1072—Shock Hazard from Interconnections, page 69
Statement 1073—No User-Serviceable Parts, page 71
Statement 1074—Comply with Local and National Electrical Codes, page 72
15
Regulatory Compliance and Safety Information for Cisco 1800 Integrated Services Routers (Fixed)
OL-10256-02
Translated Safety Warnings
Statement 1071—Warning Definition
Warning
IMPORTANT SAFETY INSTRUCTIONS
This warning symbol means danger. You are in a situation that could cause bodily injury. Before you
work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar
with standard practices for preventing accidents. Use the statement number provided at the end of
each warning to locate its translation in the translated safety warnings that accompanied this
device.
SAVE THESE INSTRUCTIONS
Waarschuwing
BELANGRIJKE VEILIGHEIDSINSTRUCTIES
Dit waarschuwingssymbool betekent gevaar. U verkeert in een situatie die lichamelijk letsel kan
veroorzaken. Voordat u aan enige apparatuur gaat werken, dient u zich bewust te zijn van de bij
elektrische schakelingen betrokken risico's en dient u op de hoogte te zijn van de standaard
praktijken om ongelukken te voorkomen. Gebruik het nummer van de verklaring onderaan de
waarschuwing als u een vertaling van de waarschuwing die bij het apparaat wordt geleverd, wilt
raadplegen.
BEWAAR DEZE INSTRUCTIES
Varoitus
TÄRKEITÄ TURVALLISUUSOHJEITA
Tämä varoitusmerkki merkitsee vaaraa. Tilanne voi aiheuttaa ruumiillisia vammoja. Ennen kuin
käsittelet laitteistoa, huomioi sähköpiirien käsittelemiseen liittyvät riskit ja tutustu
onnettomuuksien yleisiin ehkäisytapoihin. Turvallisuusvaroitusten käännökset löytyvät laitteen
mukana toimitettujen käännettyjen turvallisuusvaroitusten joukosta varoitusten lopussa näkyvien
lausuntonumeroiden avulla.
SÄILYTÄ NÄMÄ OHJEET
Attention
IMPORTANTES INFORMATIONS DE SÉCURITÉ
Ce symbole d'avertissement indique un danger. Vous vous trouvez dans une situation pouvant
entraîner des blessures ou des dommages corporels. Avant de travailler sur un équipement, soyez
conscient des dangers liés aux circuits électriques et familiarisez-vous avec les procédures
couramment utilisées pour éviter les accidents. Pour prendre connaissance des traductions des
avertissements figurant dans les consignes de sécurité traduites qui accompagnent cet appareil,
référez-vous au numéro de l'instruction situé à la fin de chaque avertissement.
CONSERVEZ CES INFORMATIONS
16
Regulatory Compliance and Safety Information for Cisco 1800 Integrated Services Routers (Fixed)
OL-10256-02
Translated Safety Warnings
Warnung
WICHTIGE SICHERHEITSHINWEISE
Dieses Warnsymbol bedeutet Gefahr. Sie befinden sich in einer Situation, die zu Verletzungen führen
kann. Machen Sie sich vor der Arbeit mit Geräten mit den Gefahren elektrischer Schaltungen und
den üblichen Verfahren zur Vorbeugung vor Unfällen vertraut. Suchen Sie mit der am Ende jeder
Warnung angegebenen Anweisungsnummer nach der jeweiligen Übersetzung in den übersetzten
Sicherheitshinweisen, die zusammen mit diesem Gerät ausgeliefert wurden.
BEWAHREN SIE DIESE HINWEISE GUT AUF.
Avvertenza
IMPORTANTI ISTRUZIONI SULLA SICUREZZA
Questo simbolo di avvertenza indica un pericolo. La situazione potrebbe causare infortuni alle
persone. Prima di intervenire su qualsiasi apparecchiatura, occorre essere al corrente dei pericoli
relativi ai circuiti elettrici e conoscere le procedure standard per la prevenzione di incidenti.
Utilizzare il numero di istruzione presente alla fine di ciascuna avvertenza per individuare le
traduzioni delle avvertenze riportate in questo documento.
CONSERVARE QUESTE ISTRUZIONI
Advarsel
VIKTIGE SIKKERHETSINSTRUKSJONER
Dette advarselssymbolet betyr fare. Du er i en situasjon som kan føre til skade på person. Før du
begynner å arbeide med noe av utstyret, må du være oppmerksom på farene forbundet med
elektriske kretser, og kjenne til standardprosedyrer for å forhindre ulykker. Bruk nummeret i slutten
av hver advarsel for å finne oversettelsen i de oversatte sikkerhetsadvarslene som fulgte med denne
enheten.
TA VARE PÅ DISSE INSTRUKSJONENE
Aviso
INSTRUÇÕES IMPORTANTES DE SEGURANÇA
Este símbolo de aviso significa perigo. Você está em uma situação que poderá ser causadora de
lesões corporais. Antes de iniciar a utilização de qualquer equipamento, tenha conhecimento dos
perigos envolvidos no manuseio de circuitos elétricos e familiarize-se com as práticas habituais de
prevenção de acidentes. Utilize o número da instrução fornecido ao final de cada aviso para
localizar sua tradução nos avisos de segurança traduzidos que acompanham este dispositivo.
GUARDE ESTAS INSTRUÇÕES
¡Advertencia!
INSTRUCCIONES IMPORTANTES DE SEGURIDAD
Este símbolo de aviso indica peligro. Existe riesgo para su integridad física. Antes de manipular
cualquier equipo, considere los riesgos de la corriente eléctrica y familiarícese con los
procedimientos estándar de prevención de accidentes. Al final de cada advertencia encontrará el
número que le ayudará a encontrar el texto traducido en el apartado de traducciones que acompaña
a este dispositivo.
GUARDE ESTAS INSTRUCCIONES
17
Regulatory Compliance and Safety Information for Cisco 1800 Integrated Services Routers (Fixed)
OL-10256-02
Translated Safety Warnings
Varning!
VIKTIGA SÄKERHETSANVISNINGAR
Denna varningssignal signalerar fara. Du befinner dig i en situation som kan leda till personskada.
Innan du utför arbete på någon utrustning måste du vara medveten om farorna med elkretsar och
känna till vanliga förfaranden för att förebygga olyckor. Använd det nummer som finns i slutet av
varje varning för att hitta dess översättning i de översatta säkerhetsvarningar som medföljer denna
anordning.
SPARA DESSA ANVISNINGAR
18
Regulatory Compliance and Safety Information for Cisco 1800 Integrated Services Routers (Fixed)
OL-10256-02
Translated Safety Warnings
Aviso
INSTRUÇÕES IMPORTANTES DE SEGURANÇA
Este símbolo de aviso significa perigo. Você se encontra em uma situação em que há risco de lesões
corporais. Antes de trabalhar com qualquer equipamento, esteja ciente dos riscos que envolvem os
circuitos elétricos e familiarize-se com as práticas padrão de prevenção de acidentes. Use o
número da declaração fornecido ao final de cada aviso para localizar sua tradução nos avisos de
segurança traduzidos que acompanham o dispositivo.
GUARDE ESTAS INSTRUÇÕES
Advarsel
VIGTIGE SIKKERHEDSANVISNINGER
Dette advarselssymbol betyder fare. Du befinder dig i en situation med risiko for
legemesbeskadigelse. Før du begynder arbejde på udstyr, skal du være opmærksom på de
involverede risici, der er ved elektriske kredsløb, og du skal sætte dig ind i standardprocedurer til
undgåelse af ulykker. Brug erklæringsnummeret efter hver advarsel for at finde oversættelsen i de
oversatte advarsler, der fulgte med denne enhed.
GEM DISSE ANVISNINGER
19
Regulatory Compliance and Safety Information for Cisco 1800 Integrated Services Routers (Fixed)
OL-10256-02
Translated Safety Warnings
20
Regulatory Compliance and Safety Information for Cisco 1800 Integrated Services Routers (Fixed)
OL-10256-02
Translated Safety Warnings
Statement 1—Power Disconnection Warning
Warning
Before working on a system that has an on/off switch, turn OFF the power and unplug the power cord.
Waarschuwing
Voordat u aan een systeem werkt dat een aan/uit schakelaar heeft, dient u de stroomvoorziening UIT
te schakelen en de stekker van het netsnoer uit het stopcontact te halen.
Varoitus
Ennen kuin teet mitään sellaiselle järjestelmälle, jossa on kaksiasentokytkin, katkaise siitä virta ja
kytke virtajohto irti.
Attention
Avant de travailler sur un système équipé d'un commutateur marche-arrêt, mettre l'appareil à l'arrêt
(OFF) et débrancher le cordon d'alimentation.
Warnung
Bevor Sie an einem System mit Ein/Aus-Schalter arbeiten, schalten Sie das System AUS und ziehen
das Netzkabel aus der Steckdose.
Avvertenza
Prima di lavorare su un sistema dotato di un interruttore on/off, spegnere (OFF) il sistema e staccare
il cavo dell’alimentazione.
Advarsel
Slå AV strømmen og trekk ut strømledningen før det utføres arbeid på et system som er utstyrt med
en av/på-bryter.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74

Cisco Systems 1800 Användarmanual

Typ
Användarmanual
Denna manual är också lämplig för