Cisco Systems 1800 Användarmanual

Americas Headquarters:

Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA

Regulatory Compliance and Safety Information

for Cisco 1800 Integrated Services

Routers (Fixed)

This publication provides international regulatory compliance and safety information for Cisco 1800

Integrated Services Routers (fixed configuration). The model numbers are printed on the bottom

homologation labels with the approval logos and certification numbers.

Use this publication with other documentation that is available for your router.

This document contains the following sections:

• Safety, page 1

• Electromagnetic Compatibility, page 4

• Telecommunications, page 8

• Declaration of Conformity Statements, page 13

• California Perchlorate Contamination Prevention Act—Title 22, California Code of Regulations,

Chapter 33, page 13

• Translated Safety Warnings, page 13

• Obtaining Documentation, Obtaining Support, and Security Guidelines, page 73

Safety

This section describes safety conditions and operating conditions for Cisco 1800 fixed configuration

routers. It contains the following:

• Agency Approvals and Standards

• Restricted Area

• Lithium Backup Battery

• Operating Conditions for Canada

2

Regulatory Compliance and Safety Information for Cisco 1800 Integrated Services Routers (Fixed)

OL-10256-02

Safety

• Operating Conditions for Australia and the European Community

• Operating Conditions for the United Kingdom

Warning

This equipment will be inoperable when mains power fails.

Statement 198

Warning

High leakage current—permanent earth connection essential before making Telecommunication

Network Connection.

Statement 343

Warning

To avoid electric shock, do not connect safety extra-low voltage (SELV) circuits to telephone-network

voltage (TNV) circuits. LAN ports contain SELV circuits, and WAN ports contain TNV circuits. Some

LAN and WAN ports both use RJ-45 connectors. Use caution when connecting cables.

Statement 1021

Warning

Never touch uninsulated telephone wires or terminals unless the telephone line has been

disconnected at the network interface.

Statement 1037

Warning

Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote

risk of electric shock from lightning.

Statement 1038

Warning

For connections outside the building where the equipment is installed, the following ports must be

connected through an approved network termination unit with integral circuit protection.

10/100/1000 Ethernet

Statement 1044

Warning

Voltages that present a shock hazard may exist on Power over Ethernet (PoE) circuits if

interconnections are made using uninsulated exposed metal contacts, conductors, or terminals.

Avoid using such interconnection methods, unless the exposed metal parts are located within a

restricted access location and users and service people who are authorized within the restricted

access location are made aware of the hazard. A restricted access area can be accessed only

through the use of a special tool, lock and key or other means of security.

Statement 1072

Warning

No user-serviceable parts inside. Do not open.

Statement 1073

Agency Approvals and Standards

This section lists the following agency approvals and standards for safety:

• CSA Certified to UL 60950 and CSA 22.2 No. 60950

• ACA to AS/NZS 60950

• CB Certificate/Test Report to IEC 60950-1, edition 1 (2001) with all country deviations, as well as

to EN 60950-1

3

Regulatory Compliance and Safety Information for Cisco 1800 Integrated Services Routers (Fixed)

OL-10256-02

Safety

Restricted Area

The following warning is applicable only in Scandinavian countries.

Warning

This unit is intended for installation in restricted access areas. A restricted access area can be

accessed only through the use of a special tool, lock and key, or other means of security.

Statement 1017

Lithium Backup Battery

Cisco 1800 fixed configuration routers have an internal real-time clock with battery backup. The backup

battery is a socketed lithium battery. This battery lasts the life of the router under the operating

environmental conditions specified for the router, and is not field-replaceable.

Note Although the lithium battery is not intended to be field-replaceable, the safety agencies require that the

following warning be included in this document.

Warning

There is the danger of explosion if the battery is replaced incorrectly. Replace the battery only with

the same or equivalent type recommended by the manufacturer. Dispose of used batteries according

to the manufacturer’s instructions.

Statement 1015

Operating Conditions for Canada

In addition to the warnings and safety guidelines listed in the “Translated Safety Warnings” section on

page 13 in this document, the following operating conditions apply to routers used in Canada:

The Canadian Department of Communications label identifies certified equipment. This certification

means that the equipment meets certain telecommunications network protective operational and safety

requirements. The Department does not guarantee that the equipment will operate to the

user’s satisfaction.

Before installing the equipment, users should ensure that it is permissible to be connected to the facilities

of the local telecommunications company. The equipment must also be installed using an acceptable

method of connection. In some cases, the company’s inside wiring associated with a single line

individual service may be extended by means of a certified connector assembly (telephone extension

cord). The customer should be aware that compliance with the above conditions may not prevent

degradation of service in some situations.

Repairs to certified equipment should be made by an authorized Canadian maintenance facility

designated by the supplier. Any repairs or alterations made by the user to this equipment, or equipment

malfunctions, may give the telecommunications company cause to request the user to disconnect the

equipment.

Users should ensure for their own protection that the electrical ground connections of the power utility,

telephone lines and internal metallic water pipe system, if present, are connected together. This

precaution may be particularly important in rural areas.

4

Regulatory Compliance and Safety Information for Cisco 1800 Integrated Services Routers (Fixed)

OL-10256-02

Electromagnetic Compatibility

Warning

Only trained and qualified personnel should be allowed to install, replace, or service this equipment.

Statement 1030

Operating Conditions for Australia and the European Community

The warnings and safety guidelines listed in the section “Translated Safety Warnings” section on page 13

in this document apply to routers used in Australia and the European Community.

Operating Conditions for the United Kingdom

In addition to the warnings and safety guidelines listed in the section “Translated Safety Warnings”

section on page 13 in this document, the following warnings and safety guidelines apply to routers used

in the United Kingdom:

• The router is designed to meet the requirements of interim CTR3 for Basic Rate Access.

• Interconnection directly, or by way of other apparatus, of ports marked:

“Safety Warning—See instructions for use”

with ports marked or not so marked may produce hazardous conditions on the network, and that

advice should be obtained from a competent engineer before such a connection is made.

• The BRI connector must be hardwired permanently to the S-reference connection point by using a

connect one-time-only, nonremovable plug (RJ-45 with the latch tab removed).

• The ports marked “10BaseT,” “Console,” and “ISDN” have a safety warning applied to them as

follows:

“These ports do not provide isolation sufficient to satisfy the requirement of EN41003; apparatus

connected to these ports should either have been approved to EN41003 or have previously been

evaluated against B5E301 British Telecommunications plc (Post Office) Technical Guides 2 or 26

and given permission to attach; any other usage will invalidate any approval given to this apparatus.”

Other usage will invalidate any approval given to this apparatus if as a result it ceases to comply with

EN41003:1993.

• This apparatus must be connected to a main socket outlet with a protective earth contact.

• Connection of power supply: The router is intended for use when supplied with power from a supply

providing 100 to 240 VAC, 50 to 60 Hz, up to 0.5A.

Electromagnetic Compatibility

This section describes electromagnetic compatibility (EMC) compliance conditions for the

Cisco 1800 fixed configuration routers. It contains the following:

• Country Approvals and Standards

• CISPR 22 Class A Warning

• FCC Part 15 Notice

• Class A Notice for Canada

• Statement 191—VCCI Class A Warning for Japan

5

Regulatory Compliance and Safety Information for Cisco 1800 Integrated Services Routers (Fixed)

OL-10256-02

Electromagnetic Compatibility

• Statement 371—Power Cable and AC Adapter for Japan

• Statement 256—Class A Warning for Hungary

• Statement 294—Class A Warning for Korea

Country Approvals and Standards

This section lists the following country approvals and standards for EMC:

• Emissions for the Cisco 1800 fixed configuration routers—47CFR15 Class A (FCC); CISPR22

Class A; EN55022 Class A; AS/NZS 3548 Class A (ACA); ICES-003 Class A (Industry Canada);

V-3 Class A (VCCI); EN61000-3-2; EN61000-3-3; EN300386 Class A; KN 22 (Korea)

• Immunity for Cisco 1800 fixed configuration routers—EN55024, EN50082-1, and EN61000-6-1

(including EN 61000-4-2 Electrostatic Discharge; EN 61000-4-3 Radiated Susceptibility; EN

61000-4-4 Electrical Fast Transients; EN 61000-4-5 Power & Signal Line Surges; EN 61000-4-6

Injected RF Swept Immunity; EN61000-4-11 Voltage Dips + Sags); EN300386

CISPR 22 Class A Warning

Warning

This is a class A product. In a domestic environment this product may cause radio interference in

which case the user may be required to take adequate measures.

FCC Part 15 Notice

Cisco 1800 fixed configuration routers comply with Part 15 of the FCC Rules. Operation is subject to

the following two conditions:

1. These devices may not cause harmful interference.

2. These devices must accept any interference received, including interference that may cause

undesired operation.

Modifying the equipment without authorization from Cisco may result in the equipment no longer

complying with FCC requirements for Class A or Class B digital devices. In that event, your right to use

the equipment may be limited by FCC regulations, and you may be required to correct any interference

to radio or television communications at your own expense.

Note This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant

to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference when the equipment is operated in a commercial environment. This equipment generates,

uses, and can radiate radio frequency energy and, if not installed and used in accordance with the

instruction manual, may cause harmful interference to radio communications. Operation of this

equipment in a residential area is likely to cause harmful interference in which case the user will be

required to correct the interference at his own expense.

6

Regulatory Compliance and Safety Information for Cisco 1800 Integrated Services Routers (Fixed)

OL-10256-02

Electromagnetic Compatibility

Class A Notice for Canada

This Class A digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.

Equipment Attachment Limitations

The Industry Canada label identifies certified equipment. This certification means that the equipment

meets certain telecommunications network protective, operational, and safety requirements as

prescribed in the appropriate Terminal Equipment Technical Requirement Documents. The Department

does not guarantee the equipment will operate to the user’s satisfaction.

Note This equipment meets the applicable Industry Canada Terminal Equipment Technical Specifications.

This is confirmed by the registration number. The abbreviation, IC, before the registration number

signifies that registration was performed based on a Declaration of Conformity indicating that Industry

Canada technical specifications were met. It does not imply that Industry Canada approved the

equipment.

Before installing this equipment, users should ensure that it is permissible to be connected to the

facilities of the local telecommunications company. The equipment must also be installed using an

acceptable method of connection. In some cases, the company’s inside wiring associated with a

single-line individual service may be extended by means of a certified connector assembly (telephone

extension cord). The customer should be aware that compliance with the above conditions might not

prevent degradation of service in some situations.

Repairs to certified equipment should be made by an authorized Canadian maintenance facility

designated by the supplier. Any repairs or alterations made by the user to this equipment, or equipment

malfunctions, may give the telecommunications company cause to request the user to disconnect the

equipment.

Users should ensure for their own protection that the electrical ground connections of the power utility,

telephone lines, and internal metallic water pipe system, if present, are connected together. This

precaution may be particularly important in rural areas.

Caution Users should not attempt to make such connections themselves, but should contact the appropriate

electrical inspection authority, or electrician, as appropriate.

7

Regulatory Compliance and Safety Information for Cisco 1800 Integrated Services Routers (Fixed)

OL-10256-02

Electromagnetic Compatibility

Statement 191—VCCI Class A Warning for Japan

Statement 371—Power Cable and AC Adapter for Japan

When installing the product, please use the provided or designated connection cables/power cables/AC

adaptors. Using any other cables/adaptors could cause a malfunction or a fire. Electrical Appliance and

Material Safety Law prohibits the use of UL-certified cables (that have the “UL” shown on the code) for

any other electrical devices than products designated by CISCO. The use of cables that are certified by

Electrical Appliance and Material Safety Law (that have “PSE” shown on the code) is not limited to

CISCO-designated products.

Statement 256—Class A Warning for Hungary

Warning

This is a Class A product based on the standard of the Voluntary Control Council for Interference by

Information Technology Equipment (VCCI). If this equipment is used in a domestic environment, radio

disturbance may arise. When such trouble occurs, the user may be required to take corrective

actions.

Warning

This equipment is a class A product and should be used and installed properly according to the

Hungarian EMC Class A requirements (MSZEN55022). Class A equipment is designed for typical

commercial establishments for which special conditions of installation and protection distance are

used.

8

Regulatory Compliance and Safety Information for Cisco 1800 Integrated Services Routers (Fixed)

OL-10256-02

Telecommunications

Statement 294—Class A Warning for Korea

Telecommunications

This section describes telecommunications compliance conditions for Cisco 1800 fixed configuration

routers. It contains the following:

• Country Approvals and Standards

• FCC Part 68 Notice

• Universal Service Order Code Jacks

• Router Port Approvals—FCC and Industry Canada

• Declarations of Conformity to R&TTE Directive 1999/5/EEC for the European Community,

Switzerland, Norway, Iceland, and Liechtenstein

Country Approvals and Standards

This section lists the following agency approvals and standards for Telecommunications:

• USA—TIA-968-A, TI.TRQ.6

• Canada—CS-03

• European Union—RTTE Directive 5/99

• Argentina—CTR 21, TBR 21

• Australia—AS/ACIF-S002, AS/ACIF-S003, AS/ACIF-S016, AS/ACIF-S031, AS/ACIF-S038,

AS/ACIF-S043, ACIF-C559

• Brazil—225-540-784, 225-540-788, CTR3, 225-100-717 Edition 3, NET 001/92 1990

• China—ITU-G.992.1, ITU-G.991.2, CTR3, ITU I.431 1993

• Hong Kong—HKTA-2011, HKTA-2013, HKTA-2014, HKTA-2017, HKTA-2033

• India—I-DCA-18-2, IR-I/TCP-01/02, IR-I/PRI-01/02

• Israel—TIA-968-A accepted, TBR21

• Japan—Technical condition (DoC acceptance in process)

• Korea—TIA-968-A/RRL 2005-96

Warning

This is a Class A Device and is registered for EMC requirements for industrial use. The seller or

buyer should be aware of this. If this type was sold or purchased by mistake, it should be replaced

with a residential-use type.

9

Regulatory Compliance and Safety Information for Cisco 1800 Integrated Services Routers (Fixed)

OL-10256-02

Telecommunications

• Mexico—TIA-968-A accepted

• New Zealand—PTC-217, PTC-220, PTC 270/272, CTR3, ACA 016, ACIF S016

• Singapore—IDA TS ADSL1 Issue 1, IDA TS ADSL 2, IDA TS HDSL, IDA TS ISDN 1 Issue 1 1999,

IDA TS ISDN 3 Issue 1 1999, IDA TS PSTN 1 Issue 4, IDA TS PSTN 1 Issue 4, IDA TS PSTN 1 Issue 4

• South Africa—DPTE-TE-001, TIA-968-A accepted

• Taiwan—PSTN01, TIA-968-A accepted

FCC Part 68 Notice

This equipment complies with Part 68 of the FCC rules. On the bottom of the chassis is a label that

contains, among other information, the FCC registration number and ringer equivalence number (REN)

for this equipment. If requested, this information must be provided to the telephone company.

If this equipment causes harm to the telephone network, the telephone company will notify you in

advance that temporary discontinuance of service may be required. If advance notice is not practical, the

telephone company will notify the customer as soon as possible. Also, you will be advised of your right

to file a complaint with the FCC if you believe it is necessary.

The telephone company may make changes in its facilities, equipment, operation, or procedures that

could affect the operation of this equipment. If this happens, the telephone company will provide

advance notice in order for you to make the necessary modifications to maintain uninterrupted service.

Normally, this equipment will be used in conjunction with FCC registered equipment that limits the

Encoded Analog Content that provides the required Billing Protection. If the connected equipment is not

of this type, an affidavit must be supplied to the telephone company where the network connection is to

be made. The affidavit is to be notarized, and is to be filed at least ten days before the initial connection.

The facility interface and service order codes are shown in Table 1.

Table 1 Cisco 1800 Fixed Configuration Routers Facility Interface and Service Order Codes

Interface Type

Facility Interface Code

(FIC)

Service Order Code

(SOC) Jack Type (USOC)

ADSL Metallic — RJ-11C

SHDSL Metallic — RJ-11C

RJ-14C

BRI - S/T 02IS5 6.0N RJ-49C via NT1

BRI-U 02IS5 6.0N RJ-49

T1 data 04DU9-BN

04DU9-DN

04DU9-1KN

04DU9-1SN

6.0N RJ-48C

T1 voice 04DU9-BN

04DU9-DN

04DU9-1KN

04DU9-1SN,

04DU9-1ZN

6.0Y RJ-48C

10

Regulatory Compliance and Safety Information for Cisco 1800 Integrated Services Routers (Fixed)

OL-10256-02

Telecommunications

Universal Service Order Code Jacks

Table 2 lists the universal service order code (USOC) jacks used by Cisco 1800 fixed configuration

routers.

FXO1 02LS2

02GS2

—RJ-11C

RJ-21X

CAMA1 02RV2-0 — RJ-11C

RJ-21X

DID (Reverse battery) 02RV2-T 9.0F (AS.2) RJ-11C

RJ-21X

E&M tie trunk TL11E

TL12E

TL31E

TL32E

9.0F RJ-2EX

RJ-2FX

RJ-2GX

RJ-2HX

Analog modem1 — — RJ-11C

DSU 56K 04DU5-24

04DU5-48

04DU5-96

04DU5-19

04DU5-38

04DU5-56

04DU5-64

04DU5-56B

6.0F RJ-48S

Table 1 Cisco 1800 Fixed Configuration Routers Facility Interface and Service Order Codes

Interface Type

Facility Interface Code

(FIC)

Service Order Code

(SOC) Jack Type (USOC)

Table 2 USOC Jacks for Cisco 1800 Routers and WAN Interface Cards

Cisco Product Number Facility Interface Code Service Order Code Jack Type

Cisco 1800 02IS5 6.0N CB-1D

Cisco 1800 02DE2 7.0Y RJ-11

Cisco 1800 02LS2 9.0Y RJ-11

WIC-1B-S/T-V3 02IS5 6.0N RJ-48C

WIC-1B-U-V2 02IS5 6.0N RJ-49C

WIC-1DSU-T1-V2 04DU9-BN/DN 6.0N RJ-48C

WIC-1DSU-56K4 04DU5-56 6.0N R3-48S

WIC-1ADSL Metallic 6.0N RJ-11

WIC-1ADSL-DG Metallic 6.0N RJ-11

11

Regulatory Compliance and Safety Information for Cisco 1800 Integrated Services Routers (Fixed)

OL-10256-02

Telecommunications

Router Port Approvals—FCC and Industry Canada

Table 3 lists the FCC and Industry Canada approvals for the router ports.

Declarations of Conformity to R&TTE Directive 1999/5/EEC for the European

Community, Switzerland, Norway, Iceland, and Liechtenstein

WIC-1ADSL-I-DG Metallic 6.0N RJ-11

WIC-1SHDSL Metallic 6.0N RJ-11

WIC-1AM 02LS2 7.0Y RJ-11

WIC-2AM 02LS2 7.0Y RJ-11

VWIC-1MFT-T1 04DU9-BN/DN 6.0N RJ-48C

VWIC-2MFT-T1 04DU9-BN/DN 6.0N RJ-48C

VWIC-2MFT-T1-DI 04DU9-BN/DN 6.0N RJ-48C

VWIC-1MFT-E1 N/A N/A RJ-48

VWIC-1MFT-G703 N/A N/A RJ-48

VWIC-2MFT-E1 N/A N/A RJ-48

VWIC-2MFT-E1-DI N/A N/A RJ-48

VWIC-2MFT-G703 N/A N/A RJ-48

Table 2 USOC Jacks for Cisco 1800 Routers and WAN Interface Cards (continued)

Cisco Product Number Facility Interface Code Service Order Code Jack Type

Table 3 Router Port Approvals—FCC and Industry Canada

Cisco Product Number Port ACTA

1

Product ID

1. Administrative Council for Terminal Attachments

Industry Canada

Approval Number

Cisco 1800 Chassis US:5B1IS01B0143 IC:2461B-0235

Cisco 1861 Chassis US:5B1IS01B0225 IC:2461B-0407

English:

This equipment is in compliance with the essential requirements and other relevant provisions of

Directive 1999/5/EC.

[Bulgarian]:

[Czech]:

Dansk

[Danish]:

Dette udstyr er i overensstemmelse med de væsentlige krav og andre relevante bestemmelser i

Direktiv 1999/5/EF.

12

Regulatory Compliance and Safety Information for Cisco 1800 Integrated Services Routers (Fixed)

OL-10256-02

Telecommunications

Deutsch

[German]:

Dieses Gerät entspricht den grundlegenden Anforderungen und den weiteren entsprechenden

Vorgaben der Richtlinie 1999/5/EU.

Eesti

[Estonian]:

See seade vastab direktiivi 1999/5/EÜ olulistele nõuetele ja teistele asjakohastele sätetele.

Español

[Spanish]:

Este equipo cumple con los requisitos esenciales asi como con otras disposiciones de la Directiva

1999/5/CE.

[Greek]:

Français

[French]:

Cet appareil est conforme aux exigences essentielles et aux autres dispositions pertinentes de la

Directive 1999/5/EC.

Íslenska

[Icelandic]:

Þetta tæki er samkvæmt grunnkröfum og öðrum viðeigandi ákvæðum Tilskipunar 1999/5/EC.

Italiano

[Italian]:

Questo apparato é conforme ai requisiti essenziali ed agli altri principi sanciti dalla Direttiva

1999/5/CE.

Latviski

[Latvian]:

[Lithuanian]:

Nederlands

[Dutch]:

Dit apparaat voldoet aan de essentiele eisen en andere van toepassing zijnde bepalingen van de

Richtlijn 1999/5/EC.

Malti

[Maltese]:

Magyar

[Hungarian]:

Norsk

[Norwegian]:

Dette utstyret er i samsvar med de grunnleggende krav og andre relevante bestemmelser i

EU-direktiv 1999/5/EF.

Polski

[Polish]:

Português

[Portuguese]:

Este equipamento está em conformidade com os requisitos essenciais e outras provisões relevantes

da Directiva 1999/5/EC.

[Romanian]:

Acest echipament este in conformitate cu cerintele esentiale si cu alte prevederi relevante ale

Directivei 1999/5/EC.

Slovensko

[Slovenian]:

Ta naprava je skladna z bistvenimi zahtevami in ostalimi relevantnimi pogoji Direktive 1999/5/EC.

Slovensky

[Slovak]:

Toto zariadenie je v zhode so základnými požiadavkami a inými príslušnými nariadeniami direktív:

1999/5/EC.

13

Regulatory Compliance and Safety Information for Cisco 1800 Integrated Services Routers (Fixed)

OL-10256-02

Declaration of Conformity Statements

The Declaration of Conformity statements for this product can be found at the following URL:

http://www.ciscofax.com

Note If you still have questions regarding the compliance of these products or you cannot find the information

you are looking for, please send an e-email request to [email protected].

California Perchlorate Contamination Prevention

Act

—Title 22, California Code of Regulations, Chapter 33

The battery inside this product might contain perchlorate, a known hazardous substance, so special

handling and disposal of this product might be necessary. For more information about perchlorate

and best management practices for perchlorate-containing substances, see

http://www.dtsc.ca.gov/HazardousWaste/Perchlorate/index.cfm.

Translated Safety Warnings

This sections contains the translations of the following warning statements that appear in the hardware

installation documentation and quick start guide for this router:

• Statement 1071—Warning Definition, page 15

• Statement 1—Power Disconnection Warning, page 20

• Statement 23—ISDN Connection Warning, page 21

• Statement 43—Jewelry Removal Warning, page 23

• Statement 94—Wrist Strap Warning, page 24

• Statement 198—Power Failure Warning, page 26

• Statement 248—Unit Mounting Warning, page 26

• Statement 343—Before Making Telecommunication Network Connection, page 27

• Statement 1001—Work During Lightning Activity, page 28

• Statement 1004—Installation Instructions, page 29

• Statement 1005—Circuit Breaker, page 30

• Statement 1006—Chassis Warning for Rack-Mounting and Servicing, page 31

Suomi

[Finnish]:

Svenska

[Swedish]:

14

Regulatory Compliance and Safety Information for Cisco 1800 Integrated Services Routers (Fixed)

OL-10256-02

Translated Safety Warnings

• Statement 1007—TN and IT Power Systems, page 37

• Statement 1015—Battery Handling, page 37

• Statement 1017—Restricted Area, page 39

• Statement 1018—Supply Circuit, page 41

• Statement 1021—SELV Circuit, page 43

• Statement 1024—Ground Conductor, page 45

• Statement 1026—WAN Port Static Shock, page 47

• Statement 1028—More Than One Power Supply, page 48

• Statement 1029—Blank Faceplates and Cover Panels, page 50

• Statement 1030—Equipment Installation, page 53

• Statement 1035—Proximity to Water, page 55

• Statement 1036—Telephone Jacks in Wet Locations, page 56

• Statement 1037—Uninsulated Wires or Terminals, page 57

• Statement 1038—Telephone Use During an Electrical Storm, page 58

• Statement 1039—Telephone Use by Gas Leak, page 59

• Statement 1040—Product Disposal, page 59

• Statement 1041—Disconnecting Telephone-Network Cables, page 61

• Statement 1043—Installation Hazard, page 62

• Statement 1044—Port Connections, page 64

• Statement 1046—Installing or Replacing the Unit, page 66

• Statement 1047—Overheating Prevention, page 67

• Statement 1072—Shock Hazard from Interconnections, page 69

• Statement 1073—No User-Serviceable Parts, page 71

• Statement 1074—Comply with Local and National Electrical Codes, page 72

15

Regulatory Compliance and Safety Information for Cisco 1800 Integrated Services Routers (Fixed)

OL-10256-02

Translated Safety Warnings

Statement 1071—Warning Definition

Warning

IMPORTANT SAFETY INSTRUCTIONS

This warning symbol means danger. You are in a situation that could cause bodily injury. Before you

work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar

with standard practices for preventing accidents. Use the statement number provided at the end of

each warning to locate its translation in the translated safety warnings that accompanied this

device.

SAVE THESE INSTRUCTIONS

Waarschuwing

BELANGRIJKE VEILIGHEIDSINSTRUCTIES

Dit waarschuwingssymbool betekent gevaar. U verkeert in een situatie die lichamelijk letsel kan

veroorzaken. Voordat u aan enige apparatuur gaat werken, dient u zich bewust te zijn van de bij

elektrische schakelingen betrokken risico's en dient u op de hoogte te zijn van de standaard

praktijken om ongelukken te voorkomen. Gebruik het nummer van de verklaring onderaan de

waarschuwing als u een vertaling van de waarschuwing die bij het apparaat wordt geleverd, wilt

raadplegen.

BEWAAR DEZE INSTRUCTIES

Varoitus

TÄRKEITÄ TURVALLISUUSOHJEITA

Tämä varoitusmerkki merkitsee vaaraa. Tilanne voi aiheuttaa ruumiillisia vammoja. Ennen kuin

käsittelet laitteistoa, huomioi sähköpiirien käsittelemiseen liittyvät riskit ja tutustu

onnettomuuksien yleisiin ehkäisytapoihin. Turvallisuusvaroitusten käännökset löytyvät laitteen

mukana toimitettujen käännettyjen turvallisuusvaroitusten joukosta varoitusten lopussa näkyvien

lausuntonumeroiden avulla.

SÄILYTÄ NÄMÄ OHJEET

Attention

IMPORTANTES INFORMATIONS DE SÉCURITÉ

Ce symbole d'avertissement indique un danger. Vous vous trouvez dans une situation pouvant

entraîner des blessures ou des dommages corporels. Avant de travailler sur un équipement, soyez

conscient des dangers liés aux circuits électriques et familiarisez-vous avec les procédures

couramment utilisées pour éviter les accidents. Pour prendre connaissance des traductions des

avertissements figurant dans les consignes de sécurité traduites qui accompagnent cet appareil,

référez-vous au numéro de l'instruction situé à la fin de chaque avertissement.

CONSERVEZ CES INFORMATIONS

16

Regulatory Compliance and Safety Information for Cisco 1800 Integrated Services Routers (Fixed)

OL-10256-02

Translated Safety Warnings

Warnung

WICHTIGE SICHERHEITSHINWEISE

Dieses Warnsymbol bedeutet Gefahr. Sie befinden sich in einer Situation, die zu Verletzungen führen

kann. Machen Sie sich vor der Arbeit mit Geräten mit den Gefahren elektrischer Schaltungen und

den üblichen Verfahren zur Vorbeugung vor Unfällen vertraut. Suchen Sie mit der am Ende jeder

Warnung angegebenen Anweisungsnummer nach der jeweiligen Übersetzung in den übersetzten

Sicherheitshinweisen, die zusammen mit diesem Gerät ausgeliefert wurden.

BEWAHREN SIE DIESE HINWEISE GUT AUF.

Avvertenza

IMPORTANTI ISTRUZIONI SULLA SICUREZZA

Questo simbolo di avvertenza indica un pericolo. La situazione potrebbe causare infortuni alle

persone. Prima di intervenire su qualsiasi apparecchiatura, occorre essere al corrente dei pericoli

relativi ai circuiti elettrici e conoscere le procedure standard per la prevenzione di incidenti.

Utilizzare il numero di istruzione presente alla fine di ciascuna avvertenza per individuare le

traduzioni delle avvertenze riportate in questo documento.

CONSERVARE QUESTE ISTRUZIONI

Advarsel

VIKTIGE SIKKERHETSINSTRUKSJONER

Dette advarselssymbolet betyr fare. Du er i en situasjon som kan føre til skade på person. Før du

begynner å arbeide med noe av utstyret, må du være oppmerksom på farene forbundet med

elektriske kretser, og kjenne til standardprosedyrer for å forhindre ulykker. Bruk nummeret i slutten

av hver advarsel for å finne oversettelsen i de oversatte sikkerhetsadvarslene som fulgte med denne

enheten.

TA VARE PÅ DISSE INSTRUKSJONENE

Aviso

INSTRUÇÕES IMPORTANTES DE SEGURANÇA

Este símbolo de aviso significa perigo. Você está em uma situação que poderá ser causadora de

lesões corporais. Antes de iniciar a utilização de qualquer equipamento, tenha conhecimento dos

perigos envolvidos no manuseio de circuitos elétricos e familiarize-se com as práticas habituais de

prevenção de acidentes. Utilize o número da instrução fornecido ao final de cada aviso para

localizar sua tradução nos avisos de segurança traduzidos que acompanham este dispositivo.

GUARDE ESTAS INSTRUÇÕES

¡Advertencia!

INSTRUCCIONES IMPORTANTES DE SEGURIDAD

Este símbolo de aviso indica peligro. Existe riesgo para su integridad física. Antes de manipular

cualquier equipo, considere los riesgos de la corriente eléctrica y familiarícese con los

procedimientos estándar de prevención de accidentes. Al final de cada advertencia encontrará el

número que le ayudará a encontrar el texto traducido en el apartado de traducciones que acompaña

a este dispositivo.

GUARDE ESTAS INSTRUCCIONES

17

Regulatory Compliance and Safety Information for Cisco 1800 Integrated Services Routers (Fixed)

OL-10256-02

Translated Safety Warnings

Varning!

VIKTIGA SÄKERHETSANVISNINGAR

Denna varningssignal signalerar fara. Du befinner dig i en situation som kan leda till personskada.

Innan du utför arbete på någon utrustning måste du vara medveten om farorna med elkretsar och

känna till vanliga förfaranden för att förebygga olyckor. Använd det nummer som finns i slutet av

varje varning för att hitta dess översättning i de översatta säkerhetsvarningar som medföljer denna

anordning.

SPARA DESSA ANVISNINGAR

18

Regulatory Compliance and Safety Information for Cisco 1800 Integrated Services Routers (Fixed)

OL-10256-02

Translated Safety Warnings

Aviso

INSTRUÇÕES IMPORTANTES DE SEGURANÇA

Este símbolo de aviso significa perigo. Você se encontra em uma situação em que há risco de lesões

corporais. Antes de trabalhar com qualquer equipamento, esteja ciente dos riscos que envolvem os

circuitos elétricos e familiarize-se com as práticas padrão de prevenção de acidentes. Use o

número da declaração fornecido ao final de cada aviso para localizar sua tradução nos avisos de

segurança traduzidos que acompanham o dispositivo.

GUARDE ESTAS INSTRUÇÕES

Advarsel

VIGTIGE SIKKERHEDSANVISNINGER

Dette advarselssymbol betyder fare. Du befinder dig i en situation med risiko for

legemesbeskadigelse. Før du begynder arbejde på udstyr, skal du være opmærksom på de

involverede risici, der er ved elektriske kredsløb, og du skal sætte dig ind i standardprocedurer til

undgåelse af ulykker. Brug erklæringsnummeret efter hver advarsel for at finde oversættelsen i de

oversatte advarsler, der fulgte med denne enhed.

GEM DISSE ANVISNINGER

19

Regulatory Compliance and Safety Information for Cisco 1800 Integrated Services Routers (Fixed)

OL-10256-02

Translated Safety Warnings

20

Regulatory Compliance and Safety Information for Cisco 1800 Integrated Services Routers (Fixed)

OL-10256-02

Translated Safety Warnings

Statement 1—Power Disconnection Warning

Warning

Before working on a system that has an on/off switch, turn OFF the power and unplug the power cord.

Waarschuwing

Voordat u aan een systeem werkt dat een aan/uit schakelaar heeft, dient u de stroomvoorziening UIT

te schakelen en de stekker van het netsnoer uit het stopcontact te halen.

Varoitus

Ennen kuin teet mitään sellaiselle järjestelmälle, jossa on kaksiasentokytkin, katkaise siitä virta ja

kytke virtajohto irti.

Attention

Avant de travailler sur un système équipé d'un commutateur marche-arrêt, mettre l'appareil à l'arrêt

(OFF) et débrancher le cordon d'alimentation.

Warnung

Bevor Sie an einem System mit Ein/Aus-Schalter arbeiten, schalten Sie das System AUS und ziehen

das Netzkabel aus der Steckdose.

Avvertenza

Prima di lavorare su un sistema dotato di un interruttore on/off, spegnere (OFF) il sistema e staccare

il cavo dell’alimentazione.

Advarsel

Slå AV strømmen og trekk ut strømledningen før det utføres arbeid på et system som er utstyrt med

en av/på-bryter.

Sidan laddas ...

Cisco Systems 1800 Användarmanual

Denna manual är också lämplig för

Cisco Systems 1800 Användarmanual

på andra språk

Relaterade papper

Andra dokument