Yamaha RX-V2500 Bruksanvisning

Kategori
Mottagare
Typ
Bruksanvisning

Denna manual är också lämplig för

YAMAHA ELECTRONICS CORPORATION, USA
6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.
YAMAHA CANADA MUSIC LTD.
135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA
YAMAHA ELECTRONIK EUROPA G.m.b.H.
SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, F.R. OF GERMANY
YAMAHA ELECTRONIQUE FRANCE S.A.
RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE
YAMAHA ELECTRONICS (UK) LTD.
YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD18 7GQ, ENGLAND
YAMAHA SCANDINAVIA A.B.
J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN
YAMAHA MUSIC AUSTRALIA PTY, LTD.
17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA
©
2004 All rights reserved.
Printed in Malaysia WD64230
RX-V2500
AV Receiver
OWNER'S MANUAL
U
RX-V2500
RX-V2500_U-cv.fm Page 1 Thursday, August 19, 2004 6:42 PM
IMPORTANT SAFETY INSTRUCTIONS
i
Explanation of Graphical Symbols
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert you to the
presence of uninsulated “dangerous voltage” within
the product’s enclosure that may be of sufficient
magnitude to constitute a risk of electric shock to
persons.
The exclamation point within an equilateral triangle
is intended to alert you to the presence of important
operating and maintenance (servicing) instructions in
the literature accompanying the appliance.
1 Read Instructions – All the safety and operating instructions
should be read before the product is operated.
2 Retain Instructions – The safety and operating instructions
should be retained for future reference.
3 Heed Warnings – All warnings on the product and in the
operating instructions should be adhered to.
4 Follow Instructions – All operating and use instructions
should be followed.
5 Cleaning – Unplug this product from the wall outlet before
cleaning. Do not use liquid cleaners or aerosol cleaners. Use
a clean, dry cloth for cleaning.
6 Attachments – Do not use attachments not recommended by
the product manufacturer as they may cause hazards.
7 Water and Moisture – Do not use this product near water –
for example, near a bath tub, wash bowl, kitchen sink, or
laundry tub; in a wet basement; or near a swimming pool;
and the like.
8 Accessories – Do not place this product on an unstable cart,
stand, tripod, bracket, or table. The product may fall,
causing serious injury to a child or adult, and serious
damage to the product. Use only with a cart, stand, tripod,
bracket, or table recommended by the manufacturer, or sold
with the product. Any mounting of the product should
follow the manufacturer’s instructions, and should use a
mounting accessory recommended by the manufacturer.
9 A product and cart combination should be moved with care.
Quick stops, excessive force, and uneven
surfaces may cause the product and cart
combination to overturn.
10 Ventilation – Slots and openings in the cabinet are provided
for ventilation and to ensure reliable operation of the
product and to protect it from overheating, and these
openings must not be blocked or covered. The openings
should never be blocked by placing the product on a bed,
sofa, rug, or other similar surface. This product should not
be placed in a built-in installation such as a bookcase or rack
unless proper ventilation is provided or the manufacturer’s
instructions have been adhered to.
11 Power Sources – This product should be operated only from
the type of power source indicated on the marking label. If
you are not sure of the type of power supply to your home,
consult your product dealer or local power company. For
products intended to operate from battery power, or other
sources, refer to the operating instructions.
12 Grounding or Polarization – This product may be equipped
with a polarized alternating current line plug (a plug having
one blade wider than the other). This plug will fit into the
power outlet only one way. This is a safety feature. If you
are unable to insert the plug fully into the outlet, try
reversing the plug. If the plug should still fail to fit, contact
your electrician to replace your obsolete outlet. Do not
defeat the safety purpose of the polarized plug.
13 Power-Cord Protection – Power-supply cords should be
routed so that they are not likely to be walked on or pinched
by items placed upon or against them, paying particular
attention to cords at plugs, convenience receptacles, and the
point where they exit from the product.
14 Lightning – For added protection for this product during a
lightning storm, or when it is left unattended and unused for
long periods of time, unplug it from the wall outlet and
disconnect the antenna or cable system. This will prevent
damage to the product due to lightning and power-line
surges.
15 Power Lines – An outside antenna system should not be
located in the vicinity of overhead power lines or other
electric light or power circuits, or where it can fall into such
power lines or circuits. When installing an outside antenna
system, extreme care should be taken to keep from touching
such power lines or circuits as contact with them might be
fatal.
16 Overloading – Do not overload wall outlets, extension
cords, or integral convenience receptacles as this can result
in a risk of fire or electric shock.
17 Object and Liquid Entry – Never push objects of any kind
into this product through openings as they may touch
dangerous voltage points or short-out parts that could result
in a fire or electric shock. Never spill liquid of any kind on
the product.
18 Servicing – Do not attempt to service this product yourself
as opening or removing covers may expose you to
dangerous voltage or other hazards. Refer all servicing to
qualified service personnel.
19 Damage Requiring Service – Unplug this product from the
wall outlet and refer servicing to qualified service personnel
under the following conditions:
a) When the power-supply cord or plug is damaged,
b) If liquid has been spilled, or objects have fallen into the
product,
c) If the product has been exposed to rain or water,
IMPORTANT SAFETY INSTRUCTIONS
CAUTION
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
00_RX-V2500U_EN.book Page i Friday, August 20, 2004 5:20 PM
IMPORTANT SAFETY INSTRUCTIONS
ii
EXAMPLE OF ANTENNA GROUNDING
MAST
GROUND
CLAMP
ANTENNA
LEAD IN
WIRE
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810–20)
GROUNDING CONDUCTORS
(NEC SECTION 810–21)
GROUND CLAMPS
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250. PART H)
ELECTRIC
SERVICE
EQUIPMENT
NEC – NATIONAL ELECTRICAL CODE
d) If the product does not operate normally by following
the operating instructions. Adjust only those controls
that are covered by the operating instructions as an
improper adjustment of other controls may result in
damage and will often require extensive work by a
qualified technician to restore the product to its normal
operation,
e) If the product has been dropped or damaged in any
way, and
f) When the product exhibits a distinct change in perfor-
mance - this indicates a need for service.
20 Replacement Parts – When replacement parts are required,
be sure the service technician has used replacement parts
specified by the manufacturer or have the same
characteristics as the original part. Unauthorized
substitutions may result in fire, electric shock, or other
hazards.
21 Safety Check – Upon completion of any service or repairs to
this product, ask the service technician to perform safety
checks to determine that the product is in proper operating
condition.
22 Wall or Ceiling Mounting – The unit should be mounted
to a wall or ceiling only as recommended by the
manufacturer.
23 Heat – The product should be situated away from heat
sources such as radiators, heat registers, stoves, or other
products (including amplifiers) that produce heat.
24 Outdoor Antenna Grounding – If an outside antenna or
cable system is connected to the product, be sure the antenna
or cable system is grounded so as to provide some
protection against voltage surges and built-up static charges.
Article 810 of the National Electrical Code, ANSI/NFPA 70,
provides information with regard to proper grounding of the
mast and supporting structure, grounding of the lead-in wire
to an antenna discharge unit, size of grounding conductors,
location of antenna discharge unit, connection to grounding
electrodes, and requirements for the grounding electrode.
Note to CATV system installer:
This reminder is provided to call the CATV system
installer’s attention to Article 820-40 of the NEC that
provides guidelines for proper grounding and, in
particular, specifies that the cable ground shall be
connected to the grounding system of the building, as
close to the point of cable entry as practical.
FCC INFORMATION (for US customers)
1 IMPORTANT NOTICE: DO NOT MODIFY THIS
UNIT!
This product, when installed as indicated in the
instructions contained in this manual, meets FCC
requirements. Modifications not expressly approved by
Yamaha may void your authority, granted by the FCC, to
use the product.
2 IMPORTANT: When connecting this product to
accessories and/or another product use only high quality
shielded cables. Cable/s supplied with this product MUST
be used. Follow all installation instructions. Failure to
follow instructions could void your FCC authorization to
use this product in the USA.
3 NOTE: This product has been tested and found to comply
with the requirements listed in FCC Regulations, Part 15
for Class “B” digital devices. Compliance with these
requirements provides a reasonable level of assurance that
your use of this product in a residential environment will
not result in harmful interference with other electronic
devices.
This equipment generates/uses radio frequencies and, if
not installed and used according to the instructions found
in the users manual, may cause interference harmful to the
operation of other electronic devices.
Compliance with FCC regulations does not guarantee that
interference will not occur in all installations. If this
product is found to be the source of interference, which
can be determined by turning the unit “OFF” and “ON”,
please try to eliminate the problem by using one of the
following measures:
Relocate either this product or the device that is being
affected by the interference.
Utilize power outlets that are on different branch (circuit
breaker or fuse) circuits or install AC line filter/s.
In the case of radio or TV interference, relocate/reorient
the antenna. If the antenna lead-in is 300 ohm ribbon lead,
change the lead-in to coaxial type cable.
If these corrective measures do not produce satisfactory
results, please contact the local retailer authorized to
distribute this type of product. If you can not locate the
appropriate retailer, please contact Yamaha Electronics
Corp., U.S.A. 6660 Orangethorpe Ave, Buena Park, CA
90620.
The above statements apply ONLY to those products
distributed by Yamaha Corporation of America or its
subsidiaries.
00_RX-V2500U_EN.book Page ii Friday, August 20, 2004 5:20 PM
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.
iii
1 To assure the finest performance, please read this manual
carefully. Keep it in a safe place for future reference.
2 Install this sound system in a well ventilated, cool, dry, clean
place — away from direct sunlight, heat sources, vibration,
dust, moisture, and/or cold. Allow ventilation space of at least
30 cm on the top, 20 cm on the left and right, and 20 cm on
the back of this unit.
3 Locate this unit away from other electrical appliances, motors,
or transformers to avoid humming sounds.
4 Do not expose this unit to sudden temperature changes from
cold to hot, and do not locate this unit in an environment with
high humidity (i.e. a room with a humidifier) to prevent
condensation inside this unit, which may cause an electrical
shock, fire, damage to this unit, and/or personal injury.
5 Avoid installing this unit where foreign object may fall onto
this unit and/or this unit may be exposed to liquid dripping or
splashing. On the top of this unit, do not place:
Other components, as they may cause damage and/or
discoloration on the surface of this unit.
Burning objects (i.e. candles), as they may cause fire,
damage to this unit, and/or personal injury.
Containers with liquid in them, as they may fall and liquid
may cause electrical shock to the user and/or damage to
this unit.
6 Do not cover this unit with a newspaper, tablecloth, curtain,
etc. in order not to obstruct heat radiation. If the temperature
inside this unit rises, it may cause fire, damage to this unit,
and/or personal injury.
7 Do not plug in this unit to a wall outlet until all connections
are complete.
8 Do not operate this unit upside-down. It may overheat,
possibly causing damage.
9 Do not use force on switches, knobs and/or cords.
10 When disconnecting the power cable from the wall outlet,
grasp the plug; do not pull the cable.
11 Do not clean this unit with chemical solvents; this might
damage the finish. Use a clean, dry cloth.
12 Only voltage specified on this unit must be used. Using this
unit with a higher voltage than specified is dangerous and may
cause fire, damage to this unit, and/or personal injury.
YAMAHA will not be held responsible for any damage
resulting from use of this unit with a voltage other than
specified.
13 To prevent damage by lightning, disconnect the power cable
from the wall outlet during an electrical storm.
14 Do not attempt to modify or fix this unit. Contact qualified
YAMAHA service personnel when any service is needed. The
cabinet should never be opened for any reasons.
15 When not planning to use this unit for long periods of time
(i.e. vacation), disconnect the AC power plug from the wall
outlet.
16 Be sure to read the “TROUBLESHOOTING” section on
common operating errors before concluding that this unit is
faulty.
17 Before moving this unit, press STANDBY/ON to set this unit
in the standby mode, and disconnect the AC power plug from
the wall outlet.
18 VOLTAGE SELECTOR (Asia and General models only)
The VOLTAGE SELECTOR on the rear panel of this unit
must be set for your local main voltage BEFORE plugging
into the AC main supply. Voltages are:
General model............. AC 110/120/220/230-240 V, 50/60 Hz
Asia model ..................................AC 220/230-240V, 50/60 Hz
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN
OR MOISTURE.
This unit is not disconnected from the AC power
source as long as it is connected to the wall outlet, even
if this unit itself is turned off. This state is called the
standby mode. In this state, this unit is designed to
consume a very small quantity of power.
FOR CANADIAN CUSTOMERS
To prevent electric shock, match wide blade of plug to
wide slot and fully insert.
This Class B digital apparatus complies with Canadian
ICES-003.
IMPORTANT
Please record the serial number of this unit in the space
below.
MODEL:
Serial No.:
The serial number is located on the rear of the unit.
Retain this Owner’s Manual in a safe place for future
reference.
00_RX-V2500U_EN.book Page iii Friday, August 20, 2004 5:20 PM
1
PREPARATIONINTRODUCTION
BASIC
OPERATION
SOUND FIELD
PROGRAMS
ADVANCED
OPERATION
ADDITIONAL
INFORMATION
FEATURES............................................................. 2
GETTING STARTED............................................ 3
Supplied accessories .................................................. 3
Installing batteries in the remote controls.................. 3
CONTROLS AND FUNCTIONS ......................... 4
Front panel ................................................................. 4
Remote control........................................................... 6
Using the remote control ........................................... 8
Front panel display .................................................... 9
Rear panel ................................................................ 11
SPEAKER SETUP ............................................... 12
Speaker placement ................................................... 12
Speaker connections ................................................ 13
CONNECTIONS .................................................. 17
Before connecting components................................ 17
Connecting video components................................. 18
Connecting audio components................................. 21
Connecting the antennas.......................................... 23
Connecting the power cable..................................... 24
Speaker impedance setting ...................................... 25
Turning on the power............................................... 25
AUTO SETUP....................................................... 26
Introduction.............................................................. 26
Optimizer microphone setup.................................... 26
Starting the setup ..................................................... 27
Confirming the results ............................................. 29
PLAYBACK.......................................................... 32
Basic operations....................................................... 32
Selecting sound field programs ............................... 33
Additional operations............................................... 34
Selecting input modes.............................................. 39
TUNING ................................................................ 40
Automatic and manual tuning.................................. 40
Presetting stations .................................................... 41
Selecting preset stations........................................... 43
Exchanging preset stations ...................................... 43
RECORDING ....................................................... 44
SOUND FIELD PROGRAM
DESCRIPTIONS...............................................45
For movie/video sources.......................................... 45
For music sources .................................................... 48
ADVANCED OPERATIONS ..............................49
Using the sleep timer ............................................... 49
SYSTEM OPTIONS .............................................50
Changing parameter settings ................................... 52
Input Select .............................................................. 53
Manual setup: Sound ............................................... 55
Manual setup: Basic................................................. 58
Manual setup: Option .............................................. 62
System Memory....................................................... 64
REMOTE CONTROL FEATURES ...................66
Control area ............................................................. 66
Setting remote control codes ................................... 67
Programming codes from other remote controls
(Learn) ................................................................. 69
Changing source names in the display window....... 71
Using the Macro feature .......................................... 72
Clearing function sets .............................................. 74
Clearing individual functions .................................. 75
Controlling each component.................................... 77
ZONE 2/ZONE 3
(U.S.A., CANADA, U.K., EUROPE AND
AUSTRALIA MODELS ONLY).....................78
Zone 2/Zone 3 connections...................................... 78
Remote controlling Zone 2/Zone 3.......................... 79
FRONT PANEL DISPLAY MENUS ..................81
Advanced setup menu.............................................. 81
Front panel display system options menu................ 82
EDITING SOUND FIELD PARAMETERS ......86
What is a sound field? ............................................. 86
Changing parameter settings ................................... 86
SOUND FIELD PARAMETER
DESCRIPTIONS...............................................87
TROUBLESHOOTING .......................................92
GLOSSARY...........................................................97
Audio formats .......................................................... 97
Sound field programs............................................... 98
Audio information ................................................... 99
Video signal information ....................................... 100
PARAMETRIC EQUALIZER
INFORMATION .............................................101
SPECIFICATIONS.............................................102
CONTENTS
INTRODUCTION
PREPARATION
BASIC OPERATION
SOUND FIELD PROGRAMS
ADVANCED OPERATION
ADDITIONAL INFORMATION
00_RX-V2500U_EN.book Page 1 Friday, August 20, 2004 5:20 PM
FEATURES
2
Built-in 7-channel power amplifier
Minimum RMS Output Power
(0.04% THD, 20 Hz – 20 kHz, 8 )
Front: 130 W + 130 W
Center: 130 W
Surround: 130 W + 130 W
Surround Back: 130 W + 130 W
Sound field features
Proprietary YAMAHA technology for the creation of
sound fields
THX Select
Dolby Digital/Dolby Digital EX decoder
DTS/DTS-ES Matrix 6.1, Discrete 6.1,
DTS Neo:6 decoder, DTS 96/24
Dolby Pro Logic/Dolby Pro Logic II/Dolby Pro Logic
IIx decoder
Virtual CINEMA DSP
SILENT CINEMA
Sophisticated AM/FM tuner
40-station random access preset tuning
Automatic preset tuning
Preset station shifting capability (preset editing)
RDS: Radio Data System receiving capability
(U.K. and Europe models only)
Other features
YPAO: YAMAHA Parametric Room Acoustic
Optimizer for automatic speaker setup
192-kHz/24-bit D/A converter
GUI (graphical user interface) menus that allow you to
optimize this unit to suit your individual audio/video
system
6 or 8-channel additional input jacks for discrete multi
channel input
Short message function
PURE DIRECT for pure fidelity sound with analog and
PCM sources
S-video signal input/output capability
Component video input/output capability
Video signal conversion (composite video
S-video component video) capability for monitor
out
Optical and coaxial digital audio signal jacks
Sleep timer
Cinema and music night listening mode
Remote control with preset remote control codes and
learning/macro capability
Zone 2/Zone 3 custom installation facility
(U.S.A., Canada, U.K., Europe and Australia models
only)
y indicates a tip for your operation.
Some operations can be performed by using either the buttons on the main unit or on the remote control. In cases when the button
names differ between the main unit and the remote control, the button name on the remote control is given in parentheses.
This manual is printed prior to production. Design and specifications are subject to change in part as a result of improvements, etc. In
case of differences between the manual and product, the product has priority.
Manufactured under license from Dolby Laboratories.
“Dolby”, “Pro Logic”, “Surround EX”, and the double-D symbol
are trademarks of Dolby Laboratories.
“SILENT CINEMA” is a trademark of YAMAHA
CORPORATION.
“DTS”, “DTS-ES”, “Neo:6” and “DTS 96/24” are trademarks of
Digital Theater Systems, Inc.
THX and the THX logo are registered trademarks of THX Ltd.
Surround EX is a jointly developed technology of THX and
Dolby Laboratories, Inc. and is a trademark of Dolby
Laboratories, Inc. All rights reserved. Used under authorization.
We Want You Listening For A Lifetime
YAMAHA and the Electronic Industries Association’s Consumer Electronics Group want you to get the most out of your
equipment by playing it at a safe level. One that lets the sound come through loud and clear without annoying blaring or
distortion – and, most importantly, without affecting your sensitive hearing. Since hearing damage from loud sounds is
often undetectable until it is too late, YAMAHA and the Electronic Industries Association’s Consumer Electronics Group
recommend you to avoid prolonged exposure from excessive volume levels.
FEATURES
00_RX-V2500U_EN.book Page 2 Friday, August 20, 2004 5:20 PM
GETTING STARTED
3
INTRODUCTION
Please check that you received all of the following parts.
\
1 Press the part and slide the battery
compartment cover off.
2 Insert four supplied batteries (AAA, LR03)
according to the polarity markings on the
inside of the battery compartment.
3 Slide the cover back until it snaps into place.
Notes on batteries
Change all of the batteries if you notice conditions such as the
operation range of the remote control decreases, the indicator
does not flash, or its light or display window become dim.
Do not use old batteries together with new ones.
Do not use different types of batteries (such as alkaline and
manganese batteries) together. Read the packaging carefully as
these different types of batteries may have the same shape and
color.
If the batteries have leaked, dispose of them immediately. Avoid
touching the leaked material or letting it come into contact with
clothing, etc. Clean the battery compartment thoroughly before
installing new batteries.
Do not throw away batteries with general house waste; dispose
of them correctly in accordance with your local regulations.
GETTING STARTED
Supplied accessories
CLEAR
LEARN
RE–NAME
MENU
FREQ/RDS EON MODE PTY SEEK START
REC
DISC SKIP
EFFECT
RETURN
DISPLAY
STRAIGHT
NIGHT
AUDIO
PURE DIRECT
ENTER
TITLE
A/B/C/D/E
SELECT
DTV DVR/VCR2VCR 1 DVD
V
-
AUX
CBL/SAT MD/TAPE
CD-R
PHONO TUNER CD
MULTI CH IN
VOL
+
3421
90
+10
ENT.
5678
POWER POWER POWER
SYSTEM
STANDBY
AVTV
SLEEP
INPUT MODE
A
B
CH
+
TV VOL
TV MUTE TV INPUT
MUTE
+
AMP
SOURCE
TV
MACROONOFF
EXIT
TOP
1
2B
THX
STANDARD SELECT EXTD. SUR
STEREO
MUSIC ENTERTAIN MOVIE
A
SPEAKERSMEMORY
Remote control Batteries (4)
(AAA, LR03)
AM loop antenna
Optimizer microphone
75-ohm/300-ohm
antenna adapter
(U.K. model only)
Speaker terminal wrench
Power cable
Indoor FM antenna
(U.K., Europe and
Australia models)
Indoor FM antenna
(U.S.A., Canada, China,
Korea, Asia and General
models)
Installing batteries in the remote
controls
1
3
2
If the remote control is without batteries for more than
2 minutes, or if exhausted batteries remain in the
remote control, the contents of the memory may be
cleared. When the memory is cleared, insert new
batteries, set up the remote control code and program
any acquired functions that may have been cleared.
00_RX-V2500U_EN.book Page 3 Friday, August 20, 2004 5:20 PM
CONTROLS AND FUNCTIONS
4
1 STANDBY/ON
Turns on this unit or sets it to the standby mode. When you
turn on this unit, you will hear a click and there will be a 6
to 7 second delay before this unit can reproduce sound.
In standby mode, this unit consumes a small amount of power in
order to receive infrared-signals from the remote control.
2 INPUT selector
Selects the input source you want to listen to or watch.
3 PURE DIRECT
Turns on or off the PURE DIRECT mode. Lights up when
turned on (see page 37).
4 Front panel display
Shows information about the operational status of this
unit.
5 PRESET/TUNING EDIT
Switches the function of PRESET/TUNING l / h
between selecting preset station numbers and tuning.
6 FM/AM
Switches the reception band between FM and AM.
7 MEMORY (MAN’L/AUTO FM)
Stores a station in the memory. Hold down this button for
more than 3 seconds to start automatic preset tuning.
8 TUNING MODE (AUTO/MAN’L MONO)
Switches the tuning mode between automatic (“AUTO
indicator on) and manual (“AUTO” indicator off).
9 Remote control sensor
Receives signals from the remote control.
0 VOLUME
Controls the output level of all audio channels.
This does not affect the REC OUT level.
A SPEAKERS A/B
Turn on or off the set of front speakers connected to the A
and/or B terminals on the rear panel at each time the
corresponding button is pressed.
CONTROLS AND FUNCTIONS
Front panel
A
SPEAKERS
MULTI CH
B
INPUT MODE
INPUT
A/B/C/D/E
SOURCE/
REMOTE
REC OUT/ZONE 2
FM/AM
EDIT
SILENT CINEMA
S VIDEO VIDEO L
VIDEO AUX
AUDIO R OPTICAL
MEMORY
PHONES
MAN'L/AUTO FM AUTO/MAN'L MONO
PRESET/
TUNING
PRESET
/TUNING
TUNING
MODE
OPTIMIZER
MIC
TONE CONTROL STRAIGHT
EFFECT
VOLUME
PROGRAM
INPUT
PURE DIRECT
STANDBY
/ON
MD/TAPEDVD
DTV
CBL/SAT
VCR 1
CD-R
TUNER
CD
DVR/
VCR2
YPAO
1 24 0
ABC EF
DHI LKJ
3 9
PQRO
EON PTY SEEK
MODE START
RDS MODE
/FREQ
M N
ZONE ON/OFF
MAIN ZONE 2
6785
G
(U.K. and Europe models only)
(U.S.A. model)
Note
00_RX-V2500U_EN.book Page 4 Friday, August 20, 2004 5:20 PM
CONTROLS AND FUNCTIONS
5
INTRODUCTION
B MULTI CH INPUT
Selects the source connected to the MULTI CH INPUT
jacks. When selected, the MULTI CH INPUT source takes
priority over the source selected with INPUT (or the input
selector buttons on the remote control).
C INPUT MODE
Sets the priority (AUTO, DTS, ANALOG) for the type of
signals received when one component is connected to two
or more of this unit’s input jacks (see page 39).
D REC OUT/ZONE 2
(U.S.A., Canada, U.K., Europe and Australia
models only)
Selects the source you want to direct to the audio/video
recorder and ZONE 2 outputs independently of the source
you are listening to or watching in the main room. When
set to the SOURCE/REMOTE position, the input source is
directed to all outputs. The source in Zone 2 and the
source you record are always identical
REC OUT (other models)
Selects the source you want to direct to the audio/video
recorder independent of the source you are listening to or
watching. When set to the SOURCE/REMOTE position,
the input source is directed to all outputs.
E OPTIMIZER MIC jack
Use to connect and input audio signals from the supplied
microphone for use with the AUTO SETUP function (see
page 26).
F A/B/C/D/E
Selects one of the 5 preset station groups (A to E).
G PRESET/TUNING l / h
Selects preset station number 1 to 8 when the colon (:) is
displayed next to the band indication in the front panel
display.
Selects the tuning frequency when the colon (:) is not
displayed.
H PHONES (SILENT CINEMA) jack
Outputs audio signals for private listening with
headphones. When you connect headphones, no signals
are output to the PRE OUT jacks or to the speakers.
All Dolby Digital and DTS audio signals are mixed down
to the front left and right channels.
I VIDEO AUX jacks
Input audio and video signals from an external source such
as a game console. To reproduce source signals from these
jacks, select V-AUX as the input source.
J ZONE ON/OFF (MAIN)
(U.S.A., Canada and Australia models only)
Turns the main unit on or to the standby mode (see
page 80).
K ZONE ON/OFF (ZONE 2)
(U.S.A., Canada and Australia models only)
Turns Zone 2 on or to the standby mode (see page 80).
L TONE CONTROL
Use to adjust the bass/treble balance for the front left/right
and center channels (see page 34).
M PROGRAM
Use to select sound field programs or adjust bass/treble
balance (in conjunction with TONE CONTROL).
N STRAIGHT/EFFECT
Switches the sound fields off or on. When STRAIGHT is
selected, input signals (2-channel or multi-channel) are
output directly from their respective speakers without
effect processing.
U.K. and Europe models only
O RDS MODE/FREQ
Press this button when the unit is receiving an RDS station
to cycle the display mode between the PS mode, PTY
mode, RT mode, CT mode (if the station offers those RDS
data service) and/or the frequency display mode.
P EON
Press this button to select a radio program type (NEWS,
INFO, AFFAIRS, SPORT) to tune in automatically.
Q PTY SEEK MODE
Press this button to set the unit to the PTY SEEK mode.
R PTY SEEK START
Press this button to begin searching for a station after the
desired program type has been selected in the PTY SEEK
mode.
Opening and closing the front panel
door
When you want to use the controls behind the front panel
door, open the door by gently pressing on the lower part of
the panel. Keep the door closed when not using these
controls.
To open, press gently on the lower part of the panel.
00_RX-V2500U_EN.book Page 5 Friday, August 20, 2004 5:20 PM
CONTROLS AND FUNCTIONS
6
This section describes the function of each control on the
remote control used to control this unit. To operate other
components, see “REMOTE CONTROL FEATURES” on
page 66.
1 Infrared window
Outputs infrared control signals. Aim this window at the
component you want to operate.
2 Transmission indicator
Flashes while the remote control is sending signals.
3 Input selector buttons
Select the input source and change the control area.
4 Display window
Shows the name of the selected source component that
you can control.
5 PRESET +/–
Selects preset station numbers when this unit is in tuner
mode.
6 LIGHT button
Press to light up remote control buttons and display
window.
7 A/B/C/D/E
Selects preset groups when this unit is in tuner mode.
8 TOP
Selects the graphical user interface (GUI) mode for your
video monitor.
9 Cursor buttons k / n / l / h / ENTER
Use to select and adjust DSP program parameters or GUI
menu items.
0 RETURN
Returns to the upper directory when in the front panel
display menu mode.
A Sound field program/Numeric buttons
Use to select sound field programs or input numbers.
Use numbers 1 through 8 to select preset stations when
this unit is in tuner mode.
B MEMORY 1/2
Use to recall favorite sound field programs, YPAO settings
or additional preset stations (see page 65).
C MACRO ON/OFF
Turns the macro function on and off.
D MACRO
Use to program a series of operations for control by a
single button (see page 72).
E STANDBY
Sets this unit in the standby mode.
F SYSTEM POWER
Turns on the power of this unit.
G INPUT MODE
Sets the priority (AUTO, DTS, ANALOG) for the type of
signals received when one component is connected to two
or more of this unit’s input jacks (see page 39).
H SLEEP
Sets the sleep timer.
Remote control
CLEAR
LEARN
RE–NAME
EXIT
MENU
FREQ/RDS EON MODE PTY SEEK START
REC
DISC SKIP
EFFECT
RETURN
DISPLAY
STRAIGHT
NIGHT
AUDIO
PURE DIRECT
ENTER
TOP
TITLE
A/B/C/D/E
PRESET
SELECT
DTV DVR/VCR2VCR 1 DVD
V
-
AUX
CBL/SAT MD/TAPE
CD-R
PHONO TUNER CD
MULTI CH IN
1
2 B
THX
STANDARD SELECT
EXTD. SUR
STEREO
MUSIC ENTERTAIN MOVIE
VOL
+
3421
90
+10
ENT.
5678
POWER POWER POWER
SYSTEM
STANDBY
AVTV
SLEEP
INPUT MODE
A
B
CH
+
TV VOL
TV MUTE TV INPUT
MUTE
+
AMP
SOURCE
TV
MACROONOFF
A
SPEAKERSMEMORY
D
E
F
H
K
L
M
N
O
J
I
P
Q
R
S
G
9
8
0
A
2
1
4
5
7
6
3
t
U
V
W
X
B
C
00_RX-V2500U_EN.book Page 6 Friday, August 20, 2004 5:20 PM
CONTROLS AND FUNCTIONS
7
INTRODUCTION
I MULTI CH IN
Selects MULTI CH INPUT when using an external
decoder (etc.).
J SELECT k/n
Selects another component that you can control
independently of the input component selected with the
input selector buttons.
K VOL +/
Increases or decreases the volume level.
L AMP/SOURCE/TV
Selects the component you want to control with the
remote control.
AMP: Set to this position to operate this unit.
SOURCE: Set to this position to operate the component
selected with an input selector button.
TV: Set to this position to operate the television.
To set the remote control codes for components, see
page 67.
M MUTE
Mutes the sound. Press again to restore the audio output to
the previous volume level.
N PURE DIRECT
Turns on or off PURE DIRECT mode (see page 37).
O EXIT
Use to exit the graphical user interface (GUI) mode.
P NIGHT
Turns on or off the night listening modes (see page 37).
Q DISPLAY
Use to enter into the front panel display menu mode.
R STRAIGHT/EFFECT
Switches the sound fields off or on. When STRAIGHT is
selected, input signals (2-channel or multi-channel) are
output directly from their respective speakers without
effect processing.
S EXTD. SUR
Switches between 5.1 or 6.1/7.1 channel playback of
multi-channel software.
T SPEAKERS A/B
Turn on or off the set of front speakers connected to the A
and/or B terminals on the rear panel at each time the
corresponding button is pressed.
U RE-NAME
Used to change the input source name in the display
window (see page 71).
V CLEAR
Used to clear functions acquired when using the learn,
macro and rename features, or setting remote control
codes (see page 74).
W LEARN
Used to set up the remote control code or program
functions from other remote controls (see page 69).
U.K. and Europe models only
X RDS tuning buttons
(Available when this unit is in tuner mode)
FREQ/RDS
Press this button when the unit is receiving an RDS station
to cycle the display between the PS mode, PTY mode, RT
mode, CT mode (if the station offers those RDS data
services) and/or the frequency display.
EON
Press this button to select a radio program type (NEWS,
INFO, AFFAIRS, SPORT) to tune in automatically.
PTY SEEK MODE
Press this button to set the unit to the PTY SEEK mode.
PTY SEEK START
Press this button to begin searching for a station after the
desired program type has been selected in the PTY SEEK
mode.
00_RX-V2500U_EN.book Page 7 Friday, August 20, 2004 5:20 PM
CONTROLS AND FUNCTIONS
8
The remote control transmits a directional infrared beam.
Be sure to aim the remote control directly at the remote
control sensor on the main unit during operation.
Handling the remote control
Do not spill water or other liquids on the remote
control.
Do not drop the remote control.
Do not leave or store the remote control in the
following types of conditions:
high humidity such as near a bath
high temperature such as near a heater or stove
extremely low temperature
dusty places
Using the remote control
A
SPEAKERS
MULTI CH
B
INPUT MODE
INPUT
TONE CONTROL STRAIGHT
EFFECT
VOLUME
PROGRAM
INPUT
STANDBY
/ON
PURE DIRECT
ZONE ON/OFF
MAIN ZONE 2
A/B/C/D/E
SOURCE
/REMOTE
REC OUT/ZONE 2
FM/AM
EDIT
PHONES
S VIDEO VIDEO L
VIDEO AUX
AUDIO R OPTICAL
MEMORY
SILENT CINEMA
MAN'L/AUTO FM AUTO/MAN'L MONO
PRESET/
TUNING
PRESET
/TUNING
TUNING
MODE
OPTIMIZER
MIC
MD/TAPEDVD
DTV
CBL/SAT
VCR 1
CD-R
TUNER
CD
DVR
/VCR2
30 30
YPAO
Approximately 6 m (20 feet)
00_RX-V2500U_EN.book Page 8 Friday, August 20, 2004 5:20 PM
CONTROLS AND FUNCTIONS
9
INTRODUCTION
1 Decoder indicators
When any of this unit’s decoders function, the respective
indicator lights up.
2 Sound field indicators
Light to indicate the active DSP sound fields.
3 NIGHT indicator
Lights up when you select night listening mode.
4 Input source indicators
A cursor lights to show the current input source.
5 CINEMA DSP indicator
Lights up when you select a CINEMA DSP sound field
program.
6 YPAO indicator
Lights up during the auto setup procedure and when the
auto setup speaker settings are used without any
modifications.
7 AUTO indicator
Lights up when this unit is in the automatic tuning mode.
8 STEREO indicator
Lights up when this unit is receiving a stereo signal for an
FM stereo broadcast while the AUTO indicator is lit.
9 VOLUME level indicator
Indicates the volume level.
0 THX indicator
Lights up when a THX program is selected.
A PCM indicator
Lights up when this unit is reproducing PCM (pulse code
modulation) digital audio signals.
B SLEEP indicator
Lights up while the sleep timer is on.
C VIRTUAL indicator
Lights up when Virtual CINEMA DSP is active (see
page 38).
D Headphones indicator
Lights up when headphones are connected.
E SP A B indicators
Light up according to the set of front speakers selected.
Both indicators light up when both sets of speakers are
selected, or when bi-wiring.
F SILENT CINEMA indicator
Lights up when headphones are connected and a sound
field program is selected (see page 34).
G Multi-information display
Shows the current sound field program name and other
information when adjusting or changing settings.
H HiFi DSP indicator
Lights up when you select a HiFi DSP sound field
program.
I MEMORY indicator
Blinks to show a station can be stored.
J TUNED indicator
Lights up when this unit is tuned into a station.
K MUTE indicator
Blinks while the MUTE function is on.
Front panel display
V–AUX
DVR/VCR2
VCR 1
CBL/SAT
DTV DVD
MD/TAPE
CD–R CD TUNER
PHONO
96
24
NIGHT
VIRTUAL
ZONE2
ZONE3
ZONE4
SLEEP
YPAO
HiFi DSP
STEREO
TUNED
EON
AUTO
MEMORY
MUTE
VOLUME
DIGITAL
PL
MATRIX
DISCRETE
PCM
THX
PL
EX
SILENT
CINEMA
A B
SP
LFE
ft
mS
dB
96/24
LL C R
SL SB SR
PL x
PS PTY RT CT
PTY
HOLD
dB
AFGHK
135678
BE
2
C
9
DIJ
PQ
LM
4
NO0
(U.S.A., Canada, U.K., Europe and
Australia models only)
(U.K. and Europe models only)
Presence DSP sound field
Listening position
Left surround
DSP sound field
Right surround
DSP sound field
Surround/surround back DSP sound field
00_RX-V2500U_EN.book Page 9 Friday, August 20, 2004 5:20 PM
CONTROLS AND FUNCTIONS
10
L 96/24 indicator
Lights up when a DTS 96/24 signal is input to this unit.
M LFE indicator
Lights up when the input signal contains an LFE signal.
N Input channel indicators
Indicate the channel components of current digital input
signal.
O Presence and surround back speaker
indicators
Indicate the connection of presence and/or surround back
speakers when using the Auto Setup setting (page 26) or
Speaker Level setting (page 61).
P ZONE 2/ZONE 3 indicators
(U.S.A., Canada, U.K., Europe and Australia
models only)
Light up when Zone 2 or Zone 3 power is on.
Q RDS indicators
(U.K. and Europe models only)
The name(s) of the RDS data offered by the currently
received RDS station light(s) up.
EON lights up when an RDS station that offers the EON
data service is being received.
PTY HOLD lights up while searching for stations in the
PTY SEEK mode.
00_RX-V2500U_EN.book Page 10 Friday, August 20, 2004 5:20 PM
CONTROLS AND FUNCTIONS
11
INTRODUCTION
1 DIGITAL OUTPUT jacks
See page 21 for details.
2 Antenna terminals
See page 23 for connection information.
3 Video component jacks
See pages 18 and 20 for connection information.
4 Audio component jacks
See page 21 for connection information.
5 Speaker terminal wrench hook
Use to store the speaker terminal wrench when not in use.
6 RS-232C terminal
(U.S.A., Canada, U.K., Europe and Australia
models only)
This is a control expansion terminal for commercial use.
Consult you dealer for details.
7 REMOTE 1/2 IN/OUT jacks
(U.S.A., Canada, U.K., Europe and Australia
models only)
See page 78 for details.
8 CONTROL OUT jacks
(U.S.A., Canada, U.K., Europe and Australia
models only)
These are control expansion terminals for commercial use.
9 AC OUTLET(S)
Use to supply power to your other A/V components (see
page 24).
0 AC INLET
Use this inlet to plug in the supplied power cable (see
page 24).
A DIGITAL INPUT jacks
See pages 18, 20 and 21 for details.
B ZONE 2 / ZONE 3 OUTPUT jacks
(U.S.A., Canada, U.K., Europe and Australia
models only)
See page 78 for details.
C MULTI CH INPUT jacks
See page 19 for connection information.
D PRE OUT jacks
See page 22 for connection information.
E Speaker terminals
See page 13 for connection information.
F PRESENCE/ZONE 2 speaker terminals
(U.S.A., Canada, U.K., Europe and Australia
models only)
PRESENCE speaker terminals
(other models)
See page 13 for connection information.
Rear panel
GND
SPEAKERS
FRONT
SURROUND
FRONT
CENTER
PRE OUT
SUB
WOOFER
SURROUND BACK/PRESENCE
SURROUND
SURROUND BACK SINGLE
CENTER
R
R
R
L
R
L
R
L
L
R
R
L
L
L
MONITOR
AUDIOVIDEO
S VIDEO
DVD
DTV
CBL/
SAT
VIDEO
IN
OUT
OUT
DVR/VCR 2
VCR 1
ZONE 2
R
L
IN
CENTERSUB WOOFER
MULTI CH INPUTOUTPUT
AUDIO
R
L
IN
(
PLAY
)
IN
(
PLAY
)
OUT
(
REC
)
OUT
(
REC
)
CD-R
MD/TAPE
CD
PHONO
SURROUND
TUNER
75
UNBAL.
AM
ANT
GND
FM ANT
DIGITAL OUTPUT
DIGITAL INPUT
OPTICAL
MD
/
TAPE
CD-R
DVD
DTV
CBL/SAT
CD
CD
DVD
COAXIAL
+
+
+
+
+
+
+
+
+
+
A
B
RS-232C
DVR/
VCR 2
CONTROL OUT
REMOTE
IN IN OUT
21
OUT
1
2
COMPONENT VIDEO
P
R
MONITOR
OUT
P
B
Y
DVD
DTVDTV
CBL/
SAT
+12V 15mA MAX.
PRESENCE/ZONE 2
ZONE 3
FRONT (6 ch)/ SB (8 ch)
AC OUTLETS
AC IN
1234678 9
FEDCB
A
0
5
(U.S.A. model)
00_RX-V2500U_EN.book Page 11 Friday, August 20, 2004 5:20 PM
SPEAKER SETUP
12
+
For best results, place the speakers as illustrated below.
.
y
The illustrations show the standard speaker setting recommended
by the ITU-R (see page 99). You can use it to enjoy CINEMA
DSP, multi-channel audio sources, and THX.
Front speakers (FR and FL)
The front speakers are used for the main source sound plus
effect sounds. Place these speakers an equal distance from
the ideal listening position. The distance of each speaker
from each side of the video monitor should be the same.
Center speaker (C)
The center speaker is for the center channel sounds
(dialog, vocals, etc.). If for some reason it is not practical
to use a center speaker, you can do without it. Best results,
however, are obtained with the full system. Align the front
face of the center speaker with the front face of your video
monitor. Place the speaker centrally between the front
speakers and as close to the monitor as possible, such as
directly over or under it.
Surround speakers (SR and SL)
The surround speakers are used for effect and surround
sounds. Place these speakers behind your listening
position, facing slightly inwards, about 1.8 m (6 ft) above
the floor.
Surround back speakers (SBR and SBL)
The surround back speakers supplement the surround
speakers and provide for more realistic front-to-back
transitions. Place these speakers directly behind the
listening position and at the same height as the surround
speakers. They should be positioned at least 30 cm (12 in)
apart. Ideally, they should be positioned at the same width
as the front speakers.
Subwoofer
The use of a subwoofer, such as the YAMAHA Active
Servo Processing Subwoofer System, is effective not only
for reinforcing bass frequencies from any or all channels,
but also for high fidelity reproduction of the LFE (low-
frequency effect) channel included in Dolby Digital and
DTS software. The position of the subwoofer is not so
critical, because low bass sounds are not highly
directional. But it is better to place the subwoofer near the
front speakers. Turn it slightly toward the center of the
room to reduce wall reflections.
Presence speakers (PR and PL)
Presence speakers supplement the sound from the front
speakers with extra ambient effects produced by CINEMA
DSP (see page 45). These effects include sounds that
filmmakers intend to locate a little farther back behind the
screen in order to create more theater-like ambience. Place
these speakers at the front of the room about 0.5 - 1 m
(1 - 3 ft) outside the front speakers, facing slightly
inwards, and about 1.8 m (6 ft) above the floor.
Surround back and presence speakers do not output sound
simultaneously. You can set to prioritize either set of speakers in
the Sound menu (see page 57).
SPEAKER SETUP
Speaker placement
More than 30 cm (12 in)
60˚
30˚
PL
PR
SBR
SBL
FL
FR
C
SL
SR
SR
80˚
SL
1.8 m (6 ft)
1.8 m (6 ft)
Note
00_RX-V2500U_EN.book Page 12 Friday, August 20, 2004 5:20 PM
13
SPEAKER SETUP
PREPARATION
Di-pole speaker layout
Either di-pole or direct radiating speaker types can be used
for THX surround. If you choose di-pole speakers, please
place the surround and surround back speakers according
to the speaker layout below.
Be sure to connect the left channel (L), right channel (R),
“+” (red) and “–” (black) properly. If the connections are
faulty, no sound will be heard from the speakers, and if the
polarity of the speaker connections is incorrect, the sound
will be unnatural and lack bass.
If you will use 6 ohm speakers, be sure to set
this unit’s speaker impedance setting to
6 ohms before using (see page 25). If you will
use 8 ohm speakers, use this unit’s initial
setting for speaker impedance.
Before connecting the speakers, make sure that this
unit is disconnected from the power source.
Do not let the bare speaker wires touch each other or do
not let them touch any metal part of this unit. This
could damage this unit and/or speakers.
Use magnetically shielded speakers. If this type of
speaker still creates interference with the monitor,
place the speakers away from the monitor.
A speaker cord is actually a pair of insulated cables
running side by side. One cable is colored or shaped
differently, perhaps with a stripe, groove or ridges.
Connect the striped (grooved, etc.) cable to the “+” (red)
terminals on this unit and your speaker. Connect the plain
cable to the “–” (black) terminals.
1 Remove approximately 10 mm (3/8 in) of
insulation from each of the speaker cables.
2 Twist the exposed wires of the cable together
to prevent short circuits.
3 Loosen the knob.
The supplied speaker terminal wrench is useful for
loosening or tightening knobs.
4 Insert one bare wire into the hole in the side
of each terminal.
FL
SR
SL
FR
C
SBR
SBL
30˚ 30˚
:Di-pole speaker
:Direction of di-pole speaker
Speaker connections
CAUTION
10 mm (3/8 in)
1
2
00_RX-V2500U_EN.book Page 13 Friday, August 20, 2004 5:20 PM
14
SPEAKER SETUP
5 Tighten the knob to secure the wire.
Connecting to PRESENCE/ZONE 2 or
PRESENCE speaker terminals
1 Open the tab.
2 Insert one bare wire into the hole of each
terminal.
3 Return the tab to secure the wire.
Banana plug connections
(With the exception of U.K., Europe and Asia models)
First, tighten the knob and then insert the banana plug
connector into the end of the corresponding terminal.
y
You can also use banana plugs with the PRESENCE/ZONE 2 and
PRESENCE speaker terminals. Open the tab, then insert one
banana plug connector into the hole of each terminal. Do not
attempt to close the tabs after connecting the banana plugs.
Red: positive (+)
Black: negative (–)
5
4
3
Speaker terminal wrench
2
1
3
Banana plug
(With the exception of U.K., Europe
and Asia models)
00_RX-V2500U_EN.book Page 14 Friday, August 20, 2004 5:20 PM
15
SPEAKER SETUP
PREPARATION
SPEAKERS
FRONT
SURROUND
FRONT
CENTER
PRE OUT
SUB
WOOFER
SURROUND BACK/PRESENCE
SURROUND
SURROUND BACK SINGLE
CENTER
R
R
R
L
R
L
R
L
L
R
R
L
L
L
+
+
+
+
+
+
+
+
+
+
A
B
PRESENCE/ZONE 2
231
7 8 65 109
4
Center
speaker
Front speakers (A)
Surround back speakers
LeftRight
LeftRight LeftRight
Surround speakers
Front
speakers
(B)
1
2
3
4
5
6
9
10
8
7
Speaker layout
(U.S.A. model)
LeftRight
Presence speakers
You can connect both surround back and presence speakers to this unit, but they do not output sound simultaneously.You can set
to prioritize either set of speakers in the Sound menu (see page 57).
The surround back speakers output the surround back channel included in Dolby Digital EX and DTS ES software and only
operate when the Dolby Digital EX, DTS ES or Dolby Pro Logic IIx decoder is turned on.
The presence speakers output ambient effects created by the DSP sound fields. They do not output sound when other sound fields
are selected.
Subwoofer with
built-in amplifier
00_RX-V2500U_EN.book Page 15 Friday, August 20, 2004 5:20 PM
16
SPEAKER SETUP
FRONT terminals
Connect one or two speaker systems to these terminals. If
you use only one speaker system, connect it to either of
the FRONT A or B terminals.
The Canada model cannot output to two separate speaker systems
simultaneously.
Bi-wired connection
The unit also allows you to make bi-wired connections to
one speaker system. Use two pairs of speaker cables for
each speaker (one pair for the woofer and one pair for the
tweeter/mid-range). To use the bi-wired connections, press
SPEAKERS A and SPEAKERS B on the front panel so
that both SP A and B light up on the front panel display.
CENTER terminals
Connect a center speaker to these terminals.
SURROUND terminals
Connect surround speakers to these terminals.
SUBWOOFER jack
Connect a subwoofer with a built-in amplifier, such as the
YAMAHA Active Servo Processing Subwoofer System,
to this jack.
SURROUND BACK terminals
Connect surround back speakers to these terminals. If you
only connect one surround back speaker, connect it to the
left (L) terminals.
PRESENCE terminals
Connect presence speakers to these terminals.
(U.S.A., Canada, U.K., Europe and Australia models only)
You can also use these terminals to connect Zone 2 speakers (see
page 63).
Note
Bi-wired connection
FRONT
R
L
+
+
+
+
A
B
This unit
Note
00_RX-V2500U_EN.book Page 16 Friday, August 20, 2004 5:20 PM
1 / 1

Yamaha RX-V2500 Bruksanvisning

Kategori
Mottagare
Typ
Bruksanvisning
Denna manual är också lämplig för