Parkside PZKS 1500 B2 Operation and Safety Notes

IAN 295934

SLIDING CROSS CUT MITRE SAW PZKS 1500 B2

PIŁA UKOŚNICA Z FUNKCJĄ POSUWU

Uwagi dotyczące obsługi i bezpieczeństwa

Tłumaczenie oryginalnej instrukcji obsługi

PL

KAP- OCH GERINGSSÅG

Drift- och säkerhetsanvisningar

Översättning av originalhandboken

SE

ZUG-KAPP-UND GEHRUNGSSÄGE

Bedienungs- und Sicherheits hinweise

Originalbetriebsanleitung

DE AT CH

SKERSAVIMO IR SULEIDIMO PJŪKLAS

Naudojimo ir saugos pastabos

Originalaus naudojimo instrukcijos vertimas

LT

KATKAISU- JA JIIRISAHA

Käyttö- ja turvallisuusohjeet

Alkuperäisen ohjeen käännös

FI

SLIDING CROSS CUT MITRE SAW

Operation and Safety Notes

Translation of original operation manual

GB IE

NI

3

NI

PL Uwagi dotyczące obsługi i bezpieczeństwa Strona 19

GB / IE/NI Operation and Safety Notes Page 1

DE / AT / CH Bedienungs-und Sicherheitshinweise Seite 101

Przed przeczytaniem proszęrozłożyć stronęz ilustracjami, a następnie proszęzapoznać sięz

wszystkimi funkcjami urządzenia.

Klappen Sie vor dem Lesen die Seite mit den Abbildungen aus und machen Sie sich anschließend

mit allen Funktionen des Gerätes vertraut.

PL

LT

FI

Before reading, unfold the page containing the illustrations and familiarise yourself with all

functions of the device.

Prieš skaitydami instrukcijąatsiverskite lapąsu paveikslėliais ir susipažinkite su visomis šio

prietaiso funkcijomis.

SE

Innan du läser utvecklar du sidan som innehåller illustrationer och bekanta dig med allt

funktioner hos enheten.

Ennen lukemista avaa sivu, joka sisältää kuvat ja tutustuta kaikkiin laitteen toimintoja.

LT Naudojimo ir saugos pastabos Puslapis

41

FI

Käyttö- ja turvallisuusohjeet Sivu 61

SE

Drift- och säkerhetsanvisningar Sida 81

2

4 5

1

101114 13 12

17

18

7

19

16

16a

40

20

15

22

25

23

24

26

27

28

29

30

31

3

121

2

3

4

5

6

7

8

9

8

16

22

12 13

6 7

988

27

15

17

6

c

a

b

32

33

11

7

10

1511 14

8

7

1615

10

1

17

3

2

4

27

30

c

34

90°

45°

20

18

17

e

35

38

36

d

19

37

14 15

4

7

16

19

18

15

4

3

7

15

21

13

39

1

GB / IE / NI

Table of contents

Explanation of the symbols on the equipment.......................................................

Introduction ...................................................................................................

Device description ..........................................................................................

Scope of delivery ............................................................................................

Intended use ..................................................................................................

Safety information ..........................................................................................

Technical data ...............................................................................................

Before starting the equipment ..........................................................................

Attachment and operation ...............................................................................

Transport ......................................................................................................

Maintenance..................................................................................................

Storage .........................................................................................................

Electrical connection .......................................................................................

Disposal ......................................................................................................

Warranty ....................................................................................................

Service-center ...............................................................................................

Declaration of conformity ................................................................................

Page 2

Page 3

Page 4

Page 5

Page 9

Page 10

Page 15

Page 16

Page 17

Page 18

Table of contents

2

GB / IE / NI

Explanation of the symbols on the equipment

GB

Caution - Read the operating instructions to

reduce the risk of inquiry

Wear safety goggles!

Wear ear-muffs!

Wear a breathing mask!

Important! Risk of injury. Never reach into the

running saw blade!

Protection Class II (double shielded)

Danger area! Keep hands, fingers or arms away

from this area.

Explanation of the symbols on the equipment

LASER

2

Attention! - Laser radiation

Do not stare into beam!

class 2 laser product

laser specification according to EN 60825-1:2014

: 650 nm P

≤

1 mW

3

GB / IE / NI

applicable regulations that apply for the

operation of the machine in your country.

Keep the operating instructions package

with the machine at all times and store it

in a plastic cover to protect it from dirt and

moisture. Read the instruction manual each

time before operating the machine and

carefully follow its information. The machine

can only be operated by persons who were

instructed concerning the operation of the

machine and who are informed about the

associated dangers. The minimum age

requirement must be complied with.

2. Device description

(Fig. 1-21)

1. Handle

2. ON/OFF switch

3. Release lever

4. Machine head

5. Movable blade guard

6. Saw blade

7. Clamping device

8. Workpiece support

9. Table insert

10. Miter lock handle

11. Miter detent lever

12. Miter angle pointer

13. Laser

14. Miter angle scale

15. Turntable

16. Fixed saw table

16a

.Mounting hole

17. Stop rail

18. Stop for cutting depth limiter

19. Screw for cutting depth limiter

20. Cover plate

21. Sawdust bag

22. Carry handle

23. Bevel angle scale

24. Bevel angle pointer

25. Locking screw for drag guide

26. Drag guide

27. Bevel locking screw

28. Screw for clamping device

1. Introduction

MANUFACTURER:

Ga-Po-Vertrieb GmbH

Heinrich-Horten-Straße 5

47906 Kempen, Germany

DEAR CUSTOMER,

We hope your new tool brings you much

enjoyment and success.

NOTE:

According to the applicable product liability

laws, the manufacturer of the device does

not assume liability for damages to the

product or damages caused by the product

that occurs due to:

• Improper handling,

• Non-compliance of the operating

instructions,

• Repairs by third parties, not by

authorized service technicians,

• Installation and replacement of non-

original spare parts,

• Application other than specified

• A breakdown of the electrical system that

occurs due to the non-compliance of the

electric regulations and VDE regulations

0100, DIN 57113 / VDE0113.

WE RECOMMEND:

Read through the complete text in the

operating instructions before installing and

commissioning the device. The operating

instructions are intended to help the user to

become familiar with the machine and take

advantage of its application possibilities

in accordance with the recommendations.

The operating instructions contain important

information on how to operate the machine

safely, professionally and economically,

how to avoid danger, costly repairs, reduce

downtimes and how to increase reliability

and service life of the machine.

In addition to the safety regulations in the

operating instructions, you have to meet the

Introduction/Device description

4

GB / IE / NI

29. Screw for workpiece support

30. Fastening bolt

31. ON/OFF switch for laser

32. Adjustment screw (90°)

33. Screw for stop rail

34. Adjustment screw (45°)

35. Flange bolt

36. Outer flange

37. Saw shaft lock

38. Inner flange

39. Screw for Laser fixing

40. Laser radiation label

a) 90° stop angle (not supplied)

b) 45° stop angle (not supplied)

c) Locking nut

d) Allen key, 6 mm

e) Allen key, 4 mm

3. Scope of delivery

• Open the packaging and remove the

device carefully.

• Remove the packaging material as well

as the packaging and transport bracing

(if available).

• Check that the delivery is complete.

• Check the device and accessory parts

(Fig. 3) for transport damage.

• If possible, store the packaging until the

warranty period has expired.

ATTENTION

The device and packaging materials are

not toys!Children must not be allowed

to play with plastic bags, film and small

parts! There is a risk of swallowing and

suffocation!

• Sliding cross cut mitre saw

• 2 x Clamping device

• 2 x Workpiece support

• Sawdust bag

• Allen key 6 mm

• Allen key 4 mm

• 2 x carbon brush

• Operating manual

• Mitre lock handle

• Carry handle

• 2 x screws for carry handle

4. Intended use

The sliding cross cut mitre saw is designed to

crosscut wood and plastic respective of the

machine’s size.The saw is not designed for

cutting firewood.

Warning!

Not use the saw to cut materials

other than those specified described in

manual.

Warning!

The supplied saw blade is only

intended for the sawing of wood! Do not use

this blade for the sawing of plastic!

The equipment is to be used only for its

prescribed purpose. Any other use is deemed

to be a case of misuse. The user / operator

and not the manufacturer will be liable for

any damage or injuries of any kind caused

as a result of this.

The equipment is to be operated only with

suitable saw blades. It is prohibited to use

any type of cuttingoff wheel.

To use the equipment properly you must also

observe the safety information, the assembly

instructions and the operating instructions

to be found in this manual. All persons who

use and service the equipment have to be

acquainted with this manual and must be

informed about the equipment’s potential

hazards. It is also imperative to observe the

accident prevention regulations in force in

your area. The same applies for the general

rules of health and safety at work.

The manufacturer will not be liable for any

changes made to the equipment nor for any

damage resulting from such changes. Even

when the equipment is used as prescribed it

Scope of delivery/Intended use

5

GB / IE / NI

is still impossible to eliminate certain residual

risk factors. The following hazards may arise

in connection with the machine’s construction

and design:

• Contact with the saw blade in the

uncovered saw zone.

• Reaching into the running saw blade (cut

injuries).

• Kick-back of workpieces and parts of

workpieces.

• Saw blade fracturing.

• Catapulting of faulty carbide tips from the

saw blade.

• Damage to hearing if ear-muffs are not

used as necessary.

• Harmful emissions of wood dust when

used in closed rooms.

Please note that our equipment has not

been designed for use in commercial, trade

or industrial applications. Our warranty

will be voided if the equipment is used in

commercial, trade or industrial businesses or

for equivalent purposes.

5. Safety information

WARNING!

When using electric tools basic

safety precautions should always be followed

to reduce the risk of fire, electric shock and

injury including the following. Read all these

instructions before attempting to operate this

production and save these instructions.

Safe Operation

1 Keep the work area orderly

- Disorder in the work area can lead to

accidents.

2 Take environmental influences into

account

- Do not expose electric tools to rain.

- Do not use electric tools in a damp or

wet environment.

- Make sure that the work area is well-

illuminated.

- Do not use electric tools where there is a

risk of fire or explosion.

3 Protect yourself from electric shock

- Avoid physical contact with earthed parts

(e.g. pipes, radiators, electric ranges,

cooling units).

4 Keep children away

- Do not allow other persons to touch the

equipment or cable, keep them away

from your work area.

5 Securely store unused electric tools

- Unused electric tools should be stored in

a dry, elevated or closed location out of

the reach of children.

6 Do not force the tool.

- It will do the job better and safer at the

rate for which it was intended.

7 Use the correct electric tool

- Do not use low-output electric tools for

heavy work.

- Do not use the electric tool for purposes

for which it is not intended. For example,

do not use handheld circular saws for the

cutting of branches or logs.

- Do not use the electric tool to cut

firewood.

8 Wear suitable clothing

- Do not wear wide clothing or jewellery,

which can become entangled in moving

parts.

- When working outdoors, anti-slip

footwear is recommended.

- Tie long hair back in a hair net.

9 Use protective equipment

- Wear protective goggles.

- Wear a mask when carrying out dust-

creating work.

10 Connect the dust extraction device

- If connections for dust extraction and

a collecting device are present, make

sure that they are connected and used

properly.

- Operation in enclosed areas is only

permitted with a suitable extraction

system.

Safety information

6

GB / IE / NI

11 Do not use the cable for purposes for

which it is not intended

- Do not use the cable to pull the plug out

of the outlet. Protect the cable from heat,

oil and sharp edges.

12 Secure the workpiece

- Use the clamping devices or a vice to

hold the workpiece in place. In this

manner, it is held more securely than with

your hand.

- An additional support is necessary for

long workpieces (table, trestle, etc.) in

order to prevent the machine from tipping

over.

- Always press the workpiece firmly

against the working plate and stop in

order to prevent bouncing and twisting of

the workpiece.

13 Avoid abnormal posture

- Make sure that you have secure footing

and always maintain your balance.

- Avoid awkward hand positions in which

a sudden slip could cause one or both

hands to come into contact with the saw

blade.

14 Take care of your tools

- Keep cutting tools sharp and clean in

order to be able to work better and more

safely.

- Follow the instructions for lubrication and

for tool replacement.

- Check the connection cable of the electric

tool regularly and have it replaced by a

recognised specialist when damaged.

- Check extension cables regularly and

replace them when damaged.

- Keep the handle dry, clean and free of

oil and grease.

15 Pull the plug out of the outlet

- Never remove loose splinters, chips or

jammed wood pieces from the running

saw blade.

- During non-use of the electric tool or prior

to maintenance and when replacing tools

such as saw blades, bits, milling heads.

16 Do not leave a tool key inserted

- Before switching on, make sure that keys

and adjusting tools are removed.

17 Avoid inadvertent starting

- Make sure that the switch is switched off

when plugging the plug into an outlet.

18 Use extension cables for outdoors

- Only use approved and appropriately

identified extension cables for use

outdoors.

- Only use cable reels in the unrolled state.

19 Remain attentive

- Pay attention to what you are doing.

Remain sensible when working. Do

not use the electric tool when you are

distracted.

20 Check the electric tool for potential

damage

- Protective devices and other parts must

be carefully inspected to ensure that they

are fault-free and function as intended

prior to continued use of the electric tool.

- Check whether the moving parts function

faultlessly and do not jam or whether

parts are damaged.

All parts must be correctly mounted and

all conditions must be fulfilled to ensure

fault-free operation of the electric tool.

- The moving protective hood may not be

fixed in the open position.

- Damaged protective devices and parts

must be properly repaired or replaced

by a recognised workshop, insofar

as nothing different is specified in the

operating manual.

- Damaged switches must be replaced at a

customer service workshop.

- Do not use any faulty or damaged

connection cables.

- Do not use any electric tool on which the

switch cannot be switched on and off.

21 ATTENTION!

- Exercise elevated caution for double

mitre cuts.

22 ATTENTION!

- The use of other insertion tools and other

accessories can entail a risk of injury.

23 Have your electric tool repaired by a

qualified person.

Safety information

7

GB / IE / NI

- This electric tool complies with the

applicable safety rules. Repairs should

only be carried out by qualified persons

using original spare parts, otherwise this

may result in considerable danger to the

user.

ADDITIONAL SAFETY

INSTRUCTIONS

1 Safety precautions

-

WARNING!

Do not use saw blades

which are damaged or deformed.

- Replace the table insert when worn.

- Only use saw blades recommended

by the manufacturer which conform to

EN 847-1.

- Do not use saw blades made of high

speed steel (HSS steel).

- Wear suitable personal protective

equipment when necessary, this could

include:

- Hearing protection to reduce the risk of

induced hearing loss,

- Eye protection. Sparks generated during

work or splinters, chippings and dust

coming from the device can lead to loss

of eyesight.

- Respiratory protection to reduce the risk

of inhalation of harmful dust,

- Gloves for handling saw blades and

rough materials. Carry saw blades in a

holder whenever practical.

- Always connect the saw to a dust

collecting device.

The emission of dust is influenced, among

other things, by the type of material to

be processed, the significance of local

separation (collection or source), and the

correct setting of the hood/guide plates/

guides.

2 Maintenance and repair

- Pull out the mains plug for any adjustment

or repair tasks.

- The generation of noise is influenced

by various factors, including the

characteristics of saw blades, condition

of saw blade and electric tool. Use saw

blades which were designed for reduced

noise development, insofar as possible.

Maintain the electric tool and tool

attachments regularly and if necessary,

initiate repairs in order to reduce noise.

- Report faults on the electric tool,

protective devices or the tool attachment

to the person responsible for safety as

soon as they are discovered.

3 Safe Operation

- Make sure that a suitable saw blade for

the material to be cut is selected.

- Never use the machine to cut other

materials as specified.

- To transport the machine follow the

procedure of point 9.

When transporting the electric tool, only

use the transport devices. Never use

the protective devices for handling or

transport.

- Operate the machine only if the

protective devices are functional, in good

condition and in the correct position.

- The floor around the machine must be

level, clean and free of loose particles,

such as chips and cutting residues.

- Only use saw blades for which the

maximum permissible speed is not lower

than the maximum spindle speed of the

machine and which are suitable for the

material to be cut.

- Be sure to only use spacers and spindle

rings specified by the manufacturer as

suitable for the intended purpose.

- Attention! Do not replace the laser by

a different type.

Safety information

8

GB / IE / NI

of rotation.

4 Do not use any insertion tools with

cracks. Sort out cracked insertion tools.

Repairs are not permitted.

5 Clean grease, oil and water off of the

clamping surfaces.

6 Do not use any loose reducing rings or

bushes for the reducing of holes on saw

blades.

7 Make sure that fixed reducer rings for

securing the insertion tool have the same

diameter and have at least 1/3 of the

cutting diameter.

8 Make sure that fixed reducer rings are

parallel to each other.

9 Handle insertion tool with caution.

They are ideally stored in the originally

package or special containers. Wear

protective gloves in order to improve grip

and to further reduce the risk of injury.

10 Prior to the use of insertion tools, make

sure that all protective devices are

properly fastened.

11 Prior to use, make sure that the insertion

tool meets the technical requirements of

this electric tool and is properly fastened.

12 Only use the supplied saw blade for

cutting wood, never for the processing of

metals.

Attention: Laser radiation

Do not stare into the beam

Class 2 laser product

laser specification according to

EN 60825-1:2014

: 650 nm P ≤ 1 mW

LASER

2

This laser radiation label located above

the laser. See fig.1 No.(40).

Protect yourself and you environment

from accidents using suitable

precautionary measures!

Repairs may only be carried out by

the manufacturer or an authorized

representative.

- Do not remove any cutting residues or

other parts of workpieces from the cutting

zone while the machine is running and

the saw unit is not at rest.

Instructions for proper and safe sawing:

a) Clamp the workpiece always at the saw

table firmly. Therefore please use the

supplied clamping device.

b) Before each cut, ensure that the machine

is stable.

c) If necessary attach the machine to

a workbench or the like. Fasten the

machine to the workbench.

d) Support long workpieces (e.g. with a

roller table) to prevent them sagging at

the end of a cut.

e) Make sure that the saw blade does not

touch the rotary table in any position by

pulling out the mains plug and rotating

the saw blade by hand in the 45° and

90° position. If necessary, readjust the

saw head.

WARNING!

This electric tool generates an

electromagnetic field during operation. This

field can impair active or passive medical

implants under certain conditions. In order to

prevent the risk of serious or deadly injuries,

we recommend that persons with medical

implants consult with their physician and the

manufacturer of the medical implant prior to

operating the electric tool.

SAFETY INSTRUCTIONS FOR THE

HANDLING OF SAW BLADES

1 Only use insertion tools if you have

mastered their use.

2 Observe the maximum speed. The

maximum speed specified on the

insertion tool may not be exceeded.if

specified,observe the speed range

3 Observe the motor / saw blade direction

Safety information

9

GB / IE / NI

• The laser outlet opening is located at the

front of the laser's visible end; see Fig.

21 No. (13).

• Do not look directly into the laser beam

with unprotected eyes.

• Never look into the path of the beam.

• Never point the laser beam towards

reflecting surfaces and persons or

animals. Even a laser beam with a low

output can cause damage to the eyes.

• Caution- methods other than those

specified here can result in dangerous

radiation exposure.

• Never open the laser module. unexpected

exposure to the beam can occur.

• The laser may not be replaced with a

different type of laser.

• Repairs of the laser may only be carried

out by the laser manufacturer or an

authorised representative.

6. Technical data

Rated voltage 220 - 240 V ~ 50Hz

Power 1200 W

Operating mode S6 25% 1500 W

Idle speed n

0

5000 min

-1

Carbide saw blade

Ø210 mm x 2,6 mm x Ø30 mm

Number of teeth 24

Mitre sawing range 0°- 45° (to left and right)

Bevel sawing range 0°- 45° to the left

Maximum cutting capability

：

Mitre/Bevel Angle

Maximum cross-section

(length and depth) of the

cut / the workpiece (mm)

Horizontal Vertical

0° 0° 340 x 62 mm

45° 0° 240 x 62 mm

0° 45° 340 x 34 mm

45° 45° 240 x 34 mm

Protection class II/

Weight approx.13 kg

Laser class 2

Wavelength of laser 650 nm

Laser output

≤

1 mW

* S6, continuous operation periodic duty.

Identical duty cycles with a period at

load followed by a period at no load.

Running time 2 minutes; duty cycle is

25% of the running time.

Minimum workpiece sizes (all workpieces

that can be clamped from the saw blade

with the supplied material clamp): 140 x

50 mm (length x width). Cutting depth,

max. (0°/0°): 62 mm

Make sure that the workpiece is always

secured with the clamping device.

Noise

Total noise values determined in accordance

with EN 61029.

sound pressure level L

pA

98.8 dB(A)

uncertainty K

pA

3 dB

sound power level L

WA

111.8 dB(A)

uncertainty K

WA

3 dB

Wear hearing protection.

The effects of noise can cause a loss of

hearing.

Vibration levels

Total vibration value at the handle

≤

2.5 m/s²

Measurement uncertainty: 1.5 m/s²

The measurements were performed in

accordance with EN 61029-1 and

EN 61029-2-9.

The specified vibration emission level was

measured on the basis of a standardised

test procedure and can be used to compare

power tools with one another.

The specified vibration emission level may

also be used to initially assess the

exposure.

Attention!

While actually using the power tool, the

vibration emission level may differ from the

level specified depending on how the power

tool is used.

Technical data

10

GB / IE / NI

Safety measures must be defined to protect

the operator. They must be based on an

assessment of exposure during actual usage

conditions (all parts of the operating

cycle must be accounted for, e.g. periods

when the power tool is switched off and

when it is switched on, but not operating

under load).

Reduce the vibration risk by

- wearing protective gloves during use and

- limiting the working time and reducing

the actual operation time.

Residual risks

The machine has been built according to

the state of the art and the recognised

technical safety requirements.However,

individual residual risks can arise during

operation.

• Health hazard due to electrical power,

with the use of improper electrical

connection cables.

• Furthermore, despite all precautions

having been met, some non-obvious

residual risks may still remain.

• Residual risks can be minimised if the

"Safety information" and the "Intended

use" are observed along with the whole

of the operating instructions.

• Do not load the machine unnecessarily:

excessive pressure when sawing will

quickly damage the saw blade, which

results in reduced output of the machine

in the processing and in cut precision.

• When cutting plastic material, please

always use clamps: the parts which

should be cut must always be fixed

between the clamps.

• Avoid accidental starting of the machine:

the operating button may not be pressed

when inserting the plug in an outlet.

• Use the tool that is recommended in this

manual. In doing so, your mitre saw

provides optimal performance.

• Hands may never enter the processing

zone when the machine is in operation.

Release the handle button and switch off

the machine prior to any operations.

7. Before starting the

equipment

• The equipment must be set up where it

can stand securely. Secure the machine

on a workbench or a stand with 4 screws

through the holes in the fixed saw table

(16).

• All covers and safety devices have to be

properly fitted before the equipment is

switched on.

• It must be possible for the blade to run

freely.

• When working with wood that has been

processed before, watch out for foreign

bodies such as nails or screws, etc.

• Before you press the ON/OFF switch

check that the saw blade is fitted

correctly. Moving parts must run

smoothly.

• Before you connect the equipment to the

power supply make sure the data on the

rating plate are dentical to the mains

data.

8. Attachment and operation

8.1 Attaching the saw

(Fig1/2/3/4/5)

WARNING! Avoid unintentional starting

of the machine. During assembly and

for all work on the machine, the power

plug must not be connected to the mains

supply.

- Attach the carry handle (22) to the

machine head (4) with 2 x screws.

Before starting the equipment/Attachment and operation

11

GB / IE / NI

- Attach the miter lock handle (10) to the

turntable (15).

- When fixing the saw to the workbench,

insert the mounting screws (not included)

through the mounting holes (16a).

• In order to adjust the turntable (15)

loosen the mitre lock handle (10) approx.

2 turns.

• Press the mitre detent lever (11) and turn

the turntable (15) and pointer (12) to the

desired angle measurement on the scale

(14), release the mitre detent lever (11)

and secure with the mitre lock handle

(10).

• Pressing the machine head (4) lightly

downwards and removing the fastening

bolt (30) from the motor bracket at the

same time disengages the saw from the

lowest position.

• Swing the machine head (4) up until the

release lever (3) latches into place.

• It is possible to secure the clamping

device (7) to the left or right on the

stationary saw bench. Insert the clamping

device (7) in the hole on the rear side of

the stop rail (17) and secure it with the

grip screw (28).

• Attach the workpiece supports (8) to the

fixed saw table (16) as shown in Figure

5 and fasten with the screw (29).

• It is possible to tilt the machine head (4)

a max. 45° to the left by loosening the

locking screw (27).

8.2 Mitre angle setting

• Nine positive miter detents are provided

for fast and accurate preset miter angles

– locations are at 45°, 30°, 22.5°, 15°

left and right, and center at 0°.

• Follow the process for mitre angle setting.

• Unlock the turntable by turning the mitre

lock handle (10) counter-clockwise.

• Move the turntable while press the mitre

detent lever (11) to align the mitre angle

pointer (12) to the desired degree on the

mitre angle scale (14).

• If the desired angle is one of the nine

positive mitre detents, release the mitre

detent lever (11), making sure the lever

snaps into position, and then secure by

tightening the mitre lock handle (10).

• If the mitre angle desired is not one of the

nine positive mitre detents, simply lock

the turntable into desired angle position

by turning the mitre lock handle (10) in

the clockwise direction.

8.3 Precision adjustment of the

blade for crosscut 90°

(Fig. 1/2/6/7)

• No stop angle included.

• Move the head (4) in position, so that

the blade (6) rests directly above the

turntable (15). Now, use locking screw

(25) to lock the drag guide (26).

• Lower the machine head (4) and secure

using the fastening bolt (30).

• Loosen the bevel locking screw (27).

• Position the angle stop (a) between the

saw blade (6) and the turntable (15).

• Release the locking nut (c) and adjust

the adjusting screw (32) until the angle

between the saw blade (6) and turntable

(15) is 90°.

• Re-tighten the locking nut (c).

• Subsequently check the position of the

angle indicator. If necessary loosen the

pointer (24) using a Philips screwdriver,

set to position 0° on the angle scale (23)

and re-tighten the retaining screw.

8.4 Precision adjustment of stop

rail for crosscut 90°

(Fig. 1/8/9)

- Bring the power tool into the working

position.

- Turn the turntable (15) to the 0° on the

mitre angle scale (14). The metre detent

lever

（

11

）

must be felt to engage in

the detent.

Attachment and operation

12

GB / IE / NI

Checking:

(see figure 9)

- Adjust an angle gauge to 90° and

position it between the stop rail (17) and

the saw blade (6) on the turntable (15).

The leg of the angle gauge must be flush

with the saw blade (6) over the complete

length.

Adjusting:

(see figure 8/9)

- Loosen all four set screws (33) and turn

the stop rail (17) until the leg of the angle

gauge is flush with the stop rail over the

complete length.

- Retighten the four set screws again.

When the mitre angle pointer (12) is not

in line with the 0° mark of mitre angle

scale (14) after adjusting, loosen the

screw on the mitre angle pointer (12)

with a philips screwdriver and align the

angle pointer pointed to the 0°mark.

8.5 Cross cut 90° and turntable 0°

(Fig. 10/12)

In the case of cutting widths up to approx.

100 mm it is possible to fix the traction

function of the saw with the locking screw

(25) in the rear position. In this position the

machine can be operated in cross cutting

mode. If the cutting width is over 100 mm

then it is necessary to ensure that the locking

screw (25) is loose and the machine head (4)

can move.

• Move the machine head (4) to its upper

position.

• Use the handle (1) to push back the

machine head (4) and fix it in this

position if required(dependent on the

cutting width).

• Place the piece of wood to be cut at the

stop rail (17) and on the turntable (15).

• Lock the material with the clamping

device (7) on the fixed saw table(16) to

prevent the material from moving during

the cutting operation.

• Operate the release lever (3) to release

the machine head (4).

• Press the ON/OFF switch (2) to start the

motor.

• With the drag guide (26) fixed in place:

Use the handle (1) to move the machine

head (4) steadily and with light pressure

downwards until the saw blade (6) has

completely cut through the work piece.

• With the drag guide (26) not fixed in

place:

Pull the machine head (4) all the way

to the front. Lower the handle (1) to the

very bottom by applying steady and

light downward pressure. Now push the

machine head (4) slowly and steadily to

the very back until the saw blade (6) has

completely cut through the work piece.

• When the cutting operation is completed,

move the machine head (4) back to its

upper (home) position and release the

ON/OFF switch (2).

Attention! The machine executes an upward

stroke automatically due to the return

spring, i.e. do not release the handle (1)

after completing the cut; instead allow the

machine head to move upwards slowly

whilst applying light counter pressure.

8.6 Cross cut 90° and metre cut 0°

- 45° (Fig. 10/11)

The crosscut saw can be used to make

crosscuts of 0° -45° to the left and 0° - 45° to

the right in relation to the stop rail.

• Loosen the metre lock handle (10) in case

it is tightened, press the metre detent

lever (11) and use the mitre lock handle

(10) to adjust the turntable (15) to the

desired angle. The mitre angle pointer

(12) on the turntable must match the

desired angle on the mitre angle scale

(14) on the fixed saw table (16).

• Re-tighten the mitre lock handle (10) in

order to secure the turntable (15).

Attachment and operation

13

GB / IE / NI

• Cut as described under section 8.5.

8.7 Precision adjustment of the

stop for bevel cut 45° (Fig.

1/12/13)

• No stop angle included.

• Lower the machine head (4) and secure

using the fastening bolt (30).

• Fix the turntable (15) in the 0° position.

• Loosen the locking screw (27) and use

the handle (1) to angle the machine head

(4) 45° to the left.

• Place the 45° - position angle stop (b)

between the saw blade (6) and turntable

(15).

• Release the locking nut (c) and adjust

the adjusting screw (34) until the angle

between the saw blade (6) and turntable

(15) is precisely 45°.

• Re-tighten the locking nut (c).

• Subsequently check the position of the

angle indicator.

If necessary loosen the bevel angle

pointer (24) using a Philips screwdriver,

set to position 45° on the bevel angle

scale (23) and re-tighten the retaining

screw.

8.8 Bevel cut 0°- 45° and mitre

cut 0° (Fig. 1/2/14)

The crosscut saw can be used to make bevel

cuts of 0° - 45° in relation to the work face.

• Move the machine head (4) to the top

position.

• Fix the turntable (15) in the 0° position.

• Loosen the locking screw (27) and use

the handle (1) to angle the machine

head (4) to the left, until the bevel angle

pointer (24) indicates the desired angle

measurement on the bevel angle scale

(23).

• Re-tighten the locking screw (27)

• Cut as described in section 8.5.

8.9 Bevel cut 0°- 45° and mitre

cut 0°- 45° (Fig. 1/2/15)

The crosscut saw can be used to make bevel

cuts to the left of 0°- 45° in relation to the

work face and, at the same time, 0° - 45° to

the left or 0° - 45° to the right in relation to

the stop rail (double mitre cut).

• Move the machine head (4) to its upper

position.

• Loosening the metre lock handle (10) and

press the metre detent lever (11).

• Using the mitre locking handle (10), set

the turntable (15) to the desired angle

(refer also to point 8.6 in this regard).

• Re-tighten the mitre lock handle (10) in

order to secure the rotary table.

• Loosen the locking screw (27) and use

the handle (1) to tilt the machine head

(4) to the left until it coincides with the

required angle value (in this connection

Parkside PZKS 1500 B2 Operation and Safety Notes

Parkside PZKS 1500 B2 Operation and Safety Notes

på andra språk

Relaterade papper

Andra dokument