Panasonic EY7442 Bruksanvisning

-

1

-

1

-

Operating Instructions

Bedienungsanleitung

Instructions d’utilisation

Istruzioni per l’uso

Gebruiksaanwijzing

Manual de instrucciones

Brugsvejledning

Driftsföreskrifter

Bruksanvisning

Käyttöohjeet

Before operating this unit, please read these instructions completely and save this manual for future use.

Vor Inbetriebnahme des Gerätes die Betriebsanleitung bitte gründlich durchlesen und diese Broschüre zum späteren Nachschlagen

sorgfältig aufbewahren.

Lire entièrement les instructions suivantes avant de faire fonctionner l’appareil et conserver ce mode d’emploi à des fins de consultation

ultérieure.

Prima di usare questa unità, leggere completamente queste istruzioni e conservare il manuale per usi futuri.

Lees deze gebruiksaanwijzing aandachtig door voor u het apparaat in gebruik neemt en bewaar de gebruiksaanwijzing voor eventuele

naslag.

Antes de usar este aparato por primera vez, lea todas las instrucciones de este manual y guarde el manual para poderlo consultar en el

futuro.

Gennemlæs denne betjeningsvejledning før brugen og gem den til fremtidig brug.

Läs igenom hela bruksanvisningen innan verktyget tas i bruk. Spara bruksanvisningen för senare användning.

Før enheten tas i bruk, vennligst les disse alle anvisningene og oppbevar deretter bruksanvisningen for senere bruk.

Lue ohjeet huolella ennen laitteen käyttöönottoa ja säilytä tämä käyttöohje tallessa tulevaa tarvetta varten.

Cordless Drill & Driver/Cordless Hammer Drill & Drive

r

Akku-Bohrschrauber/Akku-Schlagbohrschraube

r

Perceuse-visseuse sans fil/Perceuse à percussion-visseuse sans fil

Trapano avvitatore cordless/Trapano avvitatore cordless a percussione

Snoerloze schroef-boormachine/Snoerloze slagschroef-boormachine

Destornillador y taladro sin cables/Destornillador y taladro percutor sin cables

Akku bor & skruetrækker/Akku hammerbor & skruertrække

r

Sladdlös skruvdragare & borrmaskin/slagborrmaskin

Ledningløs drill og skrutrekker/Ledningløs slagdrill og skrutrekke

r

Ladattava pora & ruuvinväännin/ladattava vasaraporapora & ruuvinväännin

Model No: EY7442/EY7450/EY7950

EY7442_7450_7950(EU).indb 1 2011-3-1 11:33:56

-

2

-

Index/Index/Index/Indice/Index/Indice/Indeks/Index/Indeks/Hakemisto

English: Page 5

Deutsch: Seite 17

Français: Page 28

Italiano: Pagina 39

Nederlands: Bladzijde 49

Español: Página 60

Dansk: Side 71

Svenska: Sid 81

Norsk: Side 91

Suomi: Sivu 101

FUNCTIONAL DESCRIPTION

FUNKTIONSBESCHREIBUNG

DESCRIPTION DES FONCTIONS

DESCRIZIONE DELLE FUNZIONI

FUNCTIEBESCHRIJVING

DESCRIPCIÓN FUNCIONAL

FUNKTIONSBESKRIVELSE

FUNKTIONSBESKRIVNING

FUNKSJONSBESKRIVELSE

TOIMINTAKUVAUS

(O)

(P)

(E)

(N)

(E)

(F)

(G)

(I)

(J)

(

K)

(A)

(B)

(C)

(M)

(D)

(L)

(H)

(K)

(A)

Keyless drill chuck

Schlüsselfreies Bohrfutter

Mandrin porte-foret sans fil

Mandrino autoserrante

Boorkop zonder sleutel

Mandril sin llave

Nøglefri borepatron

Nyckellös borrchuck

Nøkkelfri drillchuck

Avaimeton poran kiinnityslaite

(B)

Clutch handle

Kupplungsring

Poignée de l’embrayage

Impugnatura frizione

Koppelingshandgreep

Mango de embrague

Koblinghåndtag

Kopplingshandtag

Koblingshåndtak

Kytkimen kahva

(C)

Speed selector switch

Bereichsschalter

Interrupteur de sélection de vitesse

Regolatore di velocità

Snelheidskeuzeschakelaar

Interruptor selector de velocidad

Hastighedsvælger

Hastighetsomkopplare

Hastighetskontroll

Nopeuden valintakytkin

(D)

Forward/Reverse lever

Rechts/Linkslauf Schalter

Levier d’inversion marche avant-marche arrière

Leva di avanzamento/inversione

Voorwaarts/achterwaarts-hendel

Palanca de avance/inversión

Greb til forlæns/baglæns retning

Riktningsomkopplare

Forover/Revers bryter

Eteenpäin/taaksepäin vipu

(E)

Alignment marks

Ausrichtmarkierungen

Marques d’alignement

Marcature allineamento

Uitlijntekens

Marcas de alineación

Flugtemærker

Anpassningsmärken

Opprettingsmerke

Sovitusmerkit

(F)

Battery pack release button

Akku-Entriegelungsknopf

Bouton de libération de batterie autonome

Tasto di rilascio pacco batteria

Accu-ontgrendeltoets

Botón de liberación de batería

Udløserknap til batteripakning

Frigöringsknapp för batteri

Utløserknapp for batteripakke

Akkupaketin irrotuspainike

(G)

Battery pack

Akku

Batterie autonome

Pacco batteria

Accu

Batería

Batteripakning

Batteri

Batteripakke

Akku

(H)

Control panel

Bedienfeld

Panneau de commande

Pannello di controllo

Bedieningspaneel

Panel de controle

Kontrolpanel

Kontrollpanel

Säätöpaneeli

(I)

Overheat warning lamp

Überhitzungs-Warnlampe

Témoin d’avertissement de surchauffe

Spia avvertenza surriscaldamento

Oververhitting-waarschuwingslampje

Luz de advertencia de sobrecalentamiento

Advarselslamp til overophedning

Varningslampa för överhettning

Varsellampe for overoppheting

Ylikuumenemisen varoituslamppu

(J)

LED light on/off button

LED-Leuchten-EIN/AUS-Taste

Bouton Marche/Arrêt de la lumière DEL

Tasto di accensione e spegnimento della luce LED

Aan/uit-toets (ON/OFF) voor LED-lampje

Botón ON/OFF de luz LED

TÆND/SLUK-knap til LED-lys

Strömbrytare för LED-ljus

PÅ/AV-knapp for LED-lys

LED-valon kytkin/katkaisupainike

(K)

LED light

LED-Leuchte

Lumière DEL

Luce LED

LED-lampje

Luz indicadora

LED-lys

LED-ljus

LED-lys

LED-valo

(L)

Battery low warning lamp

Akkuladungs-Warnlampe

Témoin d’avertissement de batterie basse

Spia avvertenza batteria scarica

Waarschuwingslampje voor lage accuspanning

Luz de aviso de baja carga de batería

Advarselslampes batterieffekt lav

Varningslampa för svagt batteri

Varsellampe for at batteriet er for lavt

Alhaisen akkujännitteen varoituslamppu

EY7442_7450_7950(EU).indb 2 2011-3-1 11:33:56

-

3

-

Index/Index/Index/Indice/Index/Indice/Indeks/Index/Indeks/Hakemisto

English: Page 5

Deutsch: Seite 17

Français: Page 28

Italiano: Pagina 39

Nederlands: Bladzijde 49

Español: Página 60

Dansk: Side 71

Svenska: Sid 81

Norsk: Side 91

Suomi: Sivu 101

FUNCTIONAL DESCRIPTION

FUNKTIONSBESCHREIBUNG

DESCRIPTION DES FONCTIONS

DESCRIZIONE DELLE FUNZIONI

FUNCTIEBESCHRIJVING

DESCRIPCIÓN FUNCIONAL

FUNKTIONSBESKRIVELSE

FUNKTIONSBESKRIVNING

FUNKSJONSBESKRIVELSE

TOIMINTAKUVAUS

(O)

(P)

(E)

(N)

(E)

(F)

(G)

(I)

(J)

(

K)

(A)

(B)

(C)

(M)

(D)

(L)

(H)

(K)

(A)

Keyless drill chuck

Schlüsselfreies Bohrfutter

Mandrin porte-foret sans fil

Mandrino autoserrante

Boorkop zonder sleutel

Mandril sin llave

Nøglefri borepatron

Nyckellös borrchuck

Nøkkelfri drillchuck

Avaimeton poran kiinnityslaite

(B)

Clutch handle

Kupplungsring

Poignée de l’embrayage

Impugnatura frizione

Koppelingshandgreep

Mango de embrague

Koblinghåndtag

Kopplingshandtag

Koblingshåndtak

Kytkimen kahva

(C)

Speed selector switch

Bereichsschalter

Interrupteur de sélection de vitesse

Regolatore di velocità

Snelheidskeuzeschakelaar

Interruptor selector de velocidad

Hastighedsvælger

Hastighetsomkopplare

Hastighetskontroll

Nopeuden valintakytkin

(D)

Forward/Reverse lever

Rechts/Linkslauf Schalter

Levier d’inversion marche avant-marche arrière

Leva di avanzamento/inversione

Voorwaarts/achterwaarts-hendel

Palanca de avance/inversión

Greb til forlæns/baglæns retning

Riktningsomkopplare

Forover/Revers bryter

Eteenpäin/taaksepäin vipu

(E)

Alignment marks

Ausrichtmarkierungen

Marques d’alignement

Marcature allineamento

Uitlijntekens

Marcas de alineación

Flugtemærker

Anpassningsmärken

Opprettingsmerke

Sovitusmerkit

(F)

Battery pack release button

Akku-Entriegelungsknopf

Bouton de libération de batterie autonome

Tasto di rilascio pacco batteria

Accu-ontgrendeltoets

Botón de liberación de batería

Udløserknap til batteripakning

Frigöringsknapp för batteri

Utløserknapp for batteripakke

Akkupaketin irrotuspainike

(G)

Battery pack

Akku

Batterie autonome

Pacco batteria

Accu

Batería

Batteripakning

Batteri

Batteripakke

Akku

(H)

Control panel

Bedienfeld

Panneau de commande

Pannello di controllo

Bedieningspaneel

Panel de controle

Kontrolpanel

Kontrollpanel

Säätöpaneeli

(I)

Overheat warning lamp

Überhitzungs-Warnlampe

Témoin d’avertissement de surchauffe

Spia avvertenza surriscaldamento

Oververhitting-waarschuwingslampje

Luz de advertencia de sobrecalentamiento

Advarselslamp til overophedning

Varningslampa för överhettning

Varsellampe for overoppheting

Ylikuumenemisen varoituslamppu

(J)

LED light on/off button

LED-Leuchten-EIN/AUS-Taste

Bouton Marche/Arrêt de la lumière DEL

Tasto di accensione e spegnimento della luce LED

Aan/uit-toets (ON/OFF) voor LED-lampje

Botón ON/OFF de luz LED

TÆND/SLUK-knap til LED-lys

Strömbrytare för LED-ljus

PÅ/AV-knapp for LED-lys

LED-valon kytkin/katkaisupainike

(K)

LED light

LED-Leuchte

Lumière DEL

Luce LED

LED-lampje

Luz indicadora

LED-lys

LED-ljus

LED-lys

LED-valo

(L)

Battery low warning lamp

Akkuladungs-Warnlampe

Témoin d’avertissement de batterie basse

Spia avvertenza batteria scarica

Waarschuwingslampje voor lage accuspanning

Luz de aviso de baja carga de batería

Advarselslampes batterieffekt lav

Varningslampa för svagt batteri

Varsellampe for at batteriet er for lavt

Alhaisen akkujännitteen varoituslamppu

EY7442_7450_7950(EU).indb 3 2011-3-1 11:33:56

-

4

-

(M)

Variable speed control trigger

Betriebsschalter

Gâchette de commande de vitesse

Grilletto di controllo velocità variable

Startschakelaar variabele snelheid

Disparador del control de velocided variable

Kontroludløser for variabel hastighed

Steglös varvtalsreglerare

Hovedbryter, trinnløs

Nopeudensäätökytkin

(N)

Support handle

Zusatzgriff

Manche de support

Maniglia di sostegno

Steungreep

Mango de soporte

Hjælpehåndtag

Stödhandtag

Støttehåndtak

Tukikahva

(O)

Battery charger

Ladegerät

Chargeur de batterie

Caricabatterie

Acculader

Cargador de batería

Batterioplader

Batteriladdare

Batterilader

Akkulaturi

(P)

Battery pack cover

Akkuabdeckung

Couvercle de la batterie autonome

Coperchio pacco batteria

Accudeksel

Cubierta de batería

Akkuafdækning

Batterilock

Batteripakkedeksel

Akun kansi

Original instructions: English

Translation of the original instructions:

Other languages

This tool, as a complete unit with a battery pack,

satisfies appropriate IP Degrees of Protection

based on the IEC regulations.

Definition of IP code

IP5X: Ingress of dust is not totally prevented,

but dust shall not penetrate in a quantity to

interfere with satisfactory operation of the tool

or to impair safety (In case that the talcum

powder under 75 μm intrudes inside the tool)

IPX6: Water projected in powerful jets against

the tool from any direction shall have no

harmful effects (In case that, with a nozzle

of 12.5 mm inner diameter, approximately

100 L/min of normal temperature water is

injected to the tool for 3 minutes from 3 meter

distance)

LIMITED WARRANTY

The rating of IP56 qualifies this tool for the

minimum impact of water or dust, but not for

the assurance of performance in such condi-

tions. See Safety and Operating Instructions

for further details for proper operation.

Read “the Safety Instructions” booklet

and the following before using.

I. INTENDED USE

These tools can be used to tighten

screws in clutch mode and to drill

holes in wood and metal in drill

mode. Additionally, model EY7950

can be used to drill holes in soft

concrete and similar materials in

hammer mode.

Read the Safety Instructions booklet

and the following before using.

II. ADDITIONAL

SAFETY RULES

1)

Wear ear protectors.

Exposure to noise can cause

hearing loss.

2)

Use auxiliary handle supplied

with the tool.

Loss of control can cause personal

injury.

3)

Hold power tools by insulated

gripping surfaces when per-

forming an operation where the

cutting tool may contact hidden

wiring

; contact with a “live” wire will

make exposed metal parts of the

tool “live” and shock the operator.

4) Wear a dust mask, if the work

causes dust.

5) Be aware that this tool is always in

an operating condition, since it

does not have to be plugged into

an electrical outlet.

6) When drilling or driving into walls,

floors, etc., "live" electrical wires

may be encountered. DO NOT

TOUCH THE CHUCK OR ANY

FRONT METAL PARTS OF THE

TOOL! Hold the tool only by the

plastic handle to prevent electric

shock in case you drill or drive into

a "live" wire.

7) If the bit becomes jammed, im-

mediately turn the trigger switch

off to prevent an overload, which

can damage the battery pack or

motor.

Use reverse motion to loosen

jammed bits.

8) Do NOT operate the For-

ward/Reverse lever when the

trigger switch is on. The battery

will discharge rapidly and dam-

age to the unit may occur.

9) During charging, the charger

may become slightly warm. This

is normal. Do NOT charge the

battery for a long period.

EY7442_7450_7950(EU).indb 4 2011-3-1 11:33:56

-

5

-

(M)

Variable speed control trigger

Betriebsschalter

Gâchette de commande de vitesse

Grilletto di controllo velocità variable

Startschakelaar variabele snelheid

Disparador del control de velocided variable

Kontroludløser for variabel hastighed

Steglös varvtalsreglerare

Hovedbryter, trinnløs

Nopeudensäätökytkin

(N)

Support handle

Zusatzgriff

Manche de support

Maniglia di sostegno

Steungreep

Mango de soporte

Hjælpehåndtag

Stödhandtag

Støttehåndtak

Tukikahva

(O)

Battery charger

Ladegerät

Chargeur de batterie

Caricabatterie

Acculader

Cargador de batería

Batterioplader

Batteriladdare

Batterilader

Akkulaturi

(P)

Battery pack cover

Akkuabdeckung

Couvercle de la batterie autonome

Coperchio pacco batteria

Accudeksel

Cubierta de batería

Akkuafdækning

Batterilock

Batteripakkedeksel

Akun kansi

Original instructions: English

Translation of the original instructions:

Other languages

This tool, as a complete unit with a battery pack,

satisfies appropriate IP Degrees of Protection

based on the IEC regulations.

Definition of IP code

IP5X: Ingress of dust is not totally prevented,

but dust shall not penetrate in a quantity to

interfere with satisfactory operation of the tool

or to impair safety (In case that the talcum

powder under 75 μm intrudes inside the tool)

IPX6: Water projected in powerful jets against

the tool from any direction shall have no

harmful effects (In case that, with a nozzle

of 12.5 mm inner diameter, approximately

100 L/min of normal temperature water is

injected to the tool for 3 minutes from 3 meter

distance)

LIMITED WARRANTY

The rating of IP56 qualifies this tool for the

minimum impact of water or dust, but not for

the assurance of performance in such condi-

tions. See Safety and Operating Instructions

for further details for proper operation.

Read “the Safety Instructions” booklet

and the following before using.

I. INTENDED USE

These tools can be used to tighten

screws in clutch mode and to drill

holes in wood and metal in drill

mode. Additionally, model EY7950

can be used to drill holes in soft

concrete and similar materials in

hammer mode.

Read the Safety Instructions booklet

and the following before using.

II. ADDITIONAL

SAFETY RULES

1)

Wear ear protectors.

Exposure to noise can cause

hearing loss.

2)

Use auxiliary handle supplied

with the tool.

Loss of control can cause personal

injury.

3)

Hold power tools by insulated

gripping surfaces when per-

forming an operation where the

cutting tool may contact hidden

wiring

; contact with a “live” wire will

make exposed metal parts of the

tool “live” and shock the operator.

4) Wear a dust mask, if the work

causes dust.

5) Be aware that this tool is always in

an operating condition, since it

does not have to be plugged into

an electrical outlet.

6) When drilling or driving into walls,

floors, etc., "live" electrical wires

may be encountered. DO NOT

TOUCH THE CHUCK OR ANY

FRONT METAL PARTS OF THE

TOOL! Hold the tool only by the

plastic handle to prevent electric

shock in case you drill or drive into

a "live" wire.

7) If the bit becomes jammed, im-

mediately turn the trigger switch

off to prevent an overload, which

can damage the battery pack or

motor.

Use reverse motion to loosen

jammed bits.

8) Do NOT operate the For-

ward/Reverse lever when the

trigger switch is on. The battery

will discharge rapidly and dam-

age to the unit may occur.

9) During charging, the charger

may become slightly warm. This

is normal. Do NOT charge the

battery for a long period.

EY7442_7450_7950(EU).indb 5 2011-3-1 11:33:56

-

6

-

10) When storing or carrying the tool,

set the Forward/Reverse lever to

the center position (switch lock).

11) Do not strain the tool by holding the

speed control trigger halfway

(speed control mode) so that the

motor stops.

12) Do not operate the speed selector

switch (LOW-HIGH) while pulling

on the speed control trigger. This

can cause the rechargeable battery

to wear quickly or damage the in-

ternal mechanism of the motor.

Symbol Meaning

V Volts

Direct current

n

0

No load speed

…min

-1

Revolutions or recip-

rocations per minutes

Ah

Electrical capacity of

battery pack

Forward rotation

Reverse rotation

Rotation with ham-

mering

Rotation only

To reduce the risk of

injury, user must read

and understand in-

struction manual.

For indoor use only.

WARNING:

• Do not use other than the Pana-

sonic battery packs that are de-

signed for use with this recharge-

able tool.

• Panasonic is not responsible for

any damage or accident caused by

the use of the recycled battery pack

and the counterfeit battery pack.

• Do not dispose of the battery pack

in a fire, or expose it to excessive

heat.

• Do not drive the likes of nails into

the battery pack, subject it to

shocks, dismantle it, or attempt to

modify it.

• Do not allow metal objects to touch

the battery pack terminals.

• Do not carry or store the battery

pack in the same container as nails

or similar metal objects.

• Do not charge the battery pack in a

high-temperature location, such as

next to a fire or in direct sunlight.

Otherwise, the battery may over-

heat, catch fire, or explode.

• Never use other than the dedicated

charger to charge the battery pack.

Otherwise, the battery may leak,

overheat, or explode.

• After removing the battery pack

from the tool or the charger, always

reattach the pack cover. Otherwise,

the battery contacts could be

shorted, leading to a risk of fire.

• When the Battery Pack Has Dete-

riorated, Replace It with a New

One.

Continued use of a damaged bat-

tery pack may result in heat gen-

eration, ignition or battery rupture.

III. ASSEMBLY

Attaching or Removing Bit

NOTE:

When attaching or removing a bit,

disconnect battery pack from tool or

place the switch in the center position

(switch lock).

This tool is equipped with a keyless

drill chuck.

1. Attachment

Insert the bit and turn the lock collar

clockwise (looking from the front) to

tighten firmly until it stops clicking.

Lock collar

2. Removal

Turn the lock collar counterclock-

wise (looking from the front), then

remove the bit.

NOTE:

If excessive play occurs in the chuck,

secure the drill in place and

open the chuck jaws by turning the

lock collar and

tighten the screw

(left-handed screw) with a screw-

driver by turning it counterclockwise

(viewed from the front).

Attaching or Removing Bat-

tery Pack

1. To connect the battery pack:

Line up the alignment marks and at-

tach the battery pack.

• Slide the battery pack until it locks

into position.

2. To remove the battery pack:

Pull the button from the front to re-

lease the battery pack.

Support handle

Place the support handle at your fa-

vorite position and tighten the handle

securely.

Always use the support handle to

ensure operating safety.

Button

A

lignment marks

Tighten

Loosen

EY7442_7450_7950(EU).indb 6 2011-3-1 11:33:57

-

7

-

10) When storing or carrying the tool,

set the Forward/Reverse lever to

the center position (switch lock).

11) Do not strain the tool by holding the

speed control trigger halfway

(speed control mode) so that the

motor stops.

12) Do not operate the speed selector

switch (LOW-HIGH) while pulling

on the speed control trigger. This

can cause the rechargeable battery

to wear quickly or damage the in-

ternal mechanism of the motor.

Symbol Meaning

V Volts

Direct current

n

0

No load speed

…min

-1

Revolutions or recip-

rocations per minutes

Ah

Electrical capacity of

battery pack

Forward rotation

Reverse rotation

Rotation with ham-

mering

Rotation only

To reduce the risk of

injury, user must read

and understand in-

struction manual.

For indoor use only.

WARNING:

• Do not use other than the Pana-

sonic battery packs that are de-

signed for use with this recharge-

able tool.

• Panasonic is not responsible for

any damage or accident caused by

the use of the recycled battery pack

and the counterfeit battery pack.

• Do not dispose of the battery pack

in a fire, or expose it to excessive

heat.

• Do not drive the likes of nails into

the battery pack, subject it to

shocks, dismantle it, or attempt to

modify it.

• Do not allow metal objects to touch

the battery pack terminals.

• Do not carry or store the battery

pack in the same container as nails

or similar metal objects.

• Do not charge the battery pack in a

high-temperature location, such as

next to a fire or in direct sunlight.

Otherwise, the battery may over-

heat, catch fire, or explode.

• Never use other than the dedicated

charger to charge the battery pack.

Otherwise, the battery may leak,

overheat, or explode.

• After removing the battery pack

from the tool or the charger, always

reattach the pack cover. Otherwise,

the battery contacts could be

shorted, leading to a risk of fire.

• When the Battery Pack Has Dete-

riorated, Replace It with a New

One.

Continued use of a damaged bat-

tery pack may result in heat gen-

eration, ignition or battery rupture.

III. ASSEMBLY

Attaching or Removing Bit

NOTE:

When attaching or removing a bit,

disconnect battery pack from tool or

place the switch in the center position

(switch lock).

This tool is equipped with a keyless

drill chuck.

1. Attachment

Insert the bit and turn the lock collar

clockwise (looking from the front) to

tighten firmly until it stops clicking.

Lock collar

2. Removal

Turn the lock collar counterclock-

wise (looking from the front), then

remove the bit.

NOTE:

If excessive play occurs in the chuck,

secure the drill in place and

open the chuck jaws by turning the

lock collar and

tighten the screw

(left-handed screw) with a screw-

driver by turning it counterclockwise

(viewed from the front).

Attaching or Removing Bat-

tery Pack

1. To connect the battery pack:

Line up the alignment marks and at-

tach the battery pack.

• Slide the battery pack until it locks

into position.

2. To remove the battery pack:

Pull the button from the front to re-

lease the battery pack.

Support handle

Place the support handle at your fa-

vorite position and tighten the handle

securely.

Always use the support handle to

ensure operating safety.

Button

A

lignment marks

Tighten

Loosen

EY7442_7450_7950(EU).indb 7 2011-3-1 11:33:57

-

8

-

IV. OPERATION

[Main Body]

Switch Operation

1. The speed increases with the

amount of depression of the trigger.

When beginning work, depress the

trigger slightly to start the rotation

slowly.

2. A feedback electronic controller is

used to give a strong torque even in

low speed.

3. The brake operates when the trig-

ger is released and the motor stops

immediately.

NOTE:

• When the brake operates, a braking

sound may be heard. This is normal.

• Sparks from the motor brush may be

visible through the body vent holes

on the back of the tool during

switching and braking due to the

load imposed on the motor. This

does not indicate a problem with the

tool.

Switch and Forward/Reverse

Lever Operation

Forward Reverse

Switch lock

CAUTION:

To prevent damage, do not operate

Forward/Reverse lever until the bit

comes to a complete stop.

Forward Rotation Switch Op-

eration

1. Push the lever for forward rotation.

2. Depress the trigger switch slightly

to start the tool slowly.

3. The speed increases with the

amount of depression of the trigger

for efficient tightening of screws

and drilling. The brake operates

and the chuck stops immediately

when the trigger is released.

4. After use, set the lever to its center

position (switch lock).

Reverse Rotation Switch Op-

eration

1. Push the lever for reverse rotation.

Check the direction of rotation be-

fore use.

2. Depress the trigger switch slightly

to start the tool slowly.

3. After use, set the lever to its center

position (switch lock).

Clutch Torque Setting

Adjust the torque to one of the 18

clutch settings or "

" position

(EY7442, EY7450).

Adjust the torque to one of the 18

clutch settings or "

", " " position

(EY7950).

NOTE:

Always make sure to stop opera-

tion of the tool and disengage it

from the work, when you select

Hammering mode from Drilling

mode or when you shift to Drilling

mode from Hammering mode by

rotating clutch handle.

LOW

HIGH

CAUTION:



If the clutch handle cannot be set at

“drilling” or “hammering” mode after

drilling with clutch function, set the

clutch handle at position 1 and oper-

ate the clutch for a second.

Speed Selection

Choose a low or high speed to suit

the use.

The more the variable speed control

trigger is pulled, the higher the speed

becomes.

WARNING:

• Do not inhale any smoke emitted

from the tool or battery pack as it

may be harmful.

CAUTION:

• Check the speed selector switch

before use.

•

Use at low speed when high torque

is needed during operation. (Using

at high speed when high torque is

required may cause a motor

breakdown.)

•

Do not use the tool in a manner

that causes the motor to lock up.

Doing so may damage the tool and

battery pack, resulting in smoke or

fire.

•

Do not operate the speed selector

switch (LOW-HIGH) while pulling

on the speed control trigger. This

can cause the rechargeable battery

to wear quickly or damage the in-

ternal mechanism of the motor.

* See specifications for "MAXIMUM

RECOMMENDED CAPACITIES".

CAUTION:

• To prevent excessive temperature in-

crease of the tool surface, do not op-

erate the tool continuously using two

or more battery packs. The tool needs

cool-off time before switching to an-

other pack.

• Do not close up vent holes on the

sides of the body during operation.

Otherwise, the machine function is

adversely affected to cause a failure.

• Do NOT strain the tool (motor). This

may cause damage to the unit.

• Use the tool in such a way as to pre-

vent the air from the body vent holes

from blowing directly onto your skin.

Otherwise, you may get burned.

Bit-locking Function

1. With the trigger switch not engaged

and a screwdriver bit locked in

place, the tool can be used as a

manual screwdriver.

(EY7442: up to 36 N·m, 367kgf-cm, 319 in-lbs)

(EY7450, 7950: up to 40 N·m, 408kgf-cm,

353 in-lbs)

There will be a little play in the

chuck, but this is not a malfunction.

2. This feature is handy for tightening

screws that require more torque

than the maximum torque of the

driver (position on the clutch), for

confirming the tightness of a screw

or to loosen an extremely tight

screw.

Control Panel

(1)

(3)

(2)

Set the clutch setting at this mark ( )

before actual operation.

EY7442_7450_7950(EU).indb 8 2011-3-1 11:33:57

-

9

-

IV. OPERATION

[Main Body]

Switch Operation

1. The speed increases with the

amount of depression of the trigger.

When beginning work, depress the

trigger slightly to start the rotation

slowly.

2. A feedback electronic controller is

used to give a strong torque even in

low speed.

3. The brake operates when the trig-

ger is released and the motor stops

immediately.

NOTE:

• When the brake operates, a braking

sound may be heard. This is normal.

• Sparks from the motor brush may be

visible through the body vent holes

on the back of the tool during

switching and braking due to the

load imposed on the motor. This

does not indicate a problem with the

tool.

Switch and Forward/Reverse

Lever Operation

Forward Reverse

Switch lock

CAUTION:

To prevent damage, do not operate

Forward/Reverse lever until the bit

comes to a complete stop.

Forward Rotation Switch Op-

eration

1. Push the lever for forward rotation.

2. Depress the trigger switch slightly

to start the tool slowly.

3. The speed increases with the

amount of depression of the trigger

for efficient tightening of screws

and drilling. The brake operates

and the chuck stops immediately

when the trigger is released.

4. After use, set the lever to its center

position (switch lock).

Reverse Rotation Switch Op-

eration

1. Push the lever for reverse rotation.

Check the direction of rotation be-

fore use.

2. Depress the trigger switch slightly

to start the tool slowly.

3. After use, set the lever to its center

position (switch lock).

Clutch Torque Setting

Adjust the torque to one of the 18

clutch settings or "

" position

(EY7442, EY7450).

Adjust the torque to one of the 18

clutch settings or "

", " " position

(EY7950).

NOTE:

Always make sure to stop opera-

tion of the tool and disengage it

from the work, when you select

Hammering mode from Drilling

mode or when you shift to Drilling

mode from Hammering mode by

rotating clutch handle.

LOW

HIGH

CAUTION:



If the clutch handle cannot be set at

“drilling” or “hammering” mode after

drilling with clutch function, set the

clutch handle at position 1 and oper-

ate the clutch for a second.

Speed Selection

Choose a low or high speed to suit

the use.

The more the variable speed control

trigger is pulled, the higher the speed

becomes.

WARNING:

• Do not inhale any smoke emitted

from the tool or battery pack as it

may be harmful.

CAUTION:

• Check the speed selector switch

before use.

•

Use at low speed when high torque

is needed during operation. (Using

at high speed when high torque is

required may cause a motor

breakdown.)

•

Do not use the tool in a manner

that causes the motor to lock up.

Doing so may damage the tool and

battery pack, resulting in smoke or

fire.

•

Do not operate the speed selector

switch (LOW-HIGH) while pulling

on the speed control trigger. This

can cause the rechargeable battery

to wear quickly or damage the in-

ternal mechanism of the motor.

* See specifications for "MAXIMUM

RECOMMENDED CAPACITIES".

CAUTION:

• To prevent excessive temperature in-

crease of the tool surface, do not op-

erate the tool continuously using two

or more battery packs. The tool needs

cool-off time before switching to an-

other pack.

• Do not close up vent holes on the

sides of the body during operation.

Otherwise, the machine function is

adversely affected to cause a failure.

• Do NOT strain the tool (motor). This

may cause damage to the unit.

• Use the tool in such a way as to pre-

vent the air from the body vent holes

from blowing directly onto your skin.

Otherwise, you may get burned.

Bit-locking Function

1. With the trigger switch not engaged

and a screwdriver bit locked in

place, the tool can be used as a

manual screwdriver.

(EY7442: up to 36 N·m, 367kgf-cm, 319 in-lbs)

(EY7450, 7950: up to 40 N·m, 408kgf-cm,

353 in-lbs)

There will be a little play in the

chuck, but this is not a malfunction.

2. This feature is handy for tightening

screws that require more torque

than the maximum torque of the

driver (position on the clutch), for

confirming the tightness of a screw

or to loosen an extremely tight

screw.

Control Panel

(1)

(3)

(2)

Set the clutch setting at this mark ( )

before actual operation.

EY7442_7450_7950(EU).indb 9 2011-3-1 11:33:57

-

10

-

(1) LED light

CAUTION:

• The built-in LED light is designed to

illuminate the small work area tempo-

rarily.

• Do not use it as a substitute for a reg-

ular flashlight, since it does not have

enough brightness.

• LED light turns off when the tool has

not been used for 5 minutes.

Caution: DO NOT STARE INTO BEAM.

Use of controls or adjustments or

performance of procedures other than

those specified herein may result in

hazardous radiation exposure.

(2) Overheat warning lamp

To protect the motor or battery, be

sure to note the following when car-

rying out this operation.

• If the motor or battery becomes hot,

the protection function will be acti-

vated and the motor or battery will

stop operating. The overheat warn-

ing lamp on the control panel illumi-

nates or flashes when this feature is

active.

• If the overheating protection feature

activates, allow the tool to cool tho-

roughly (at least 30 minutes). The

tool is ready for use when the over-

heat warning lamp goes out.

• Avoid using the tool in a way that

causes the overheating protection

feature to activate repeatedly.

• If the tool is operated continuously

under high-load conditions or if it is

used in hot-temperature conditions

(such as during summer), the over-

heating protection feature may acti-

vate frequently.

• If the tool is used in cold-temperature

conditions (such as during winter) or

if it is frequently stopped during use,

the overheating protection feature

may not activate.

• The performance of the EY9L42 de-

teriorates significantly at and below

10°C due to work conditions and

other factors.

(3) Battery low warning lamp

Excessive (complete) discharging of

lithium ion batteries shortens their

service life dramatically. The driver

includes a battery protection feature

designed to prevent excessive dis-

charging of the battery pack.

• The battery protection feature acti-

vates immediately before the battery

loses its charge, causing the battery

low warning lamp to flash.

• If you notice the battery low warning

lamp flashing, charge the battery

pack immediately.

Off

(normal

operation)

Flashing

(No charge)

Battery protection

feature active

Off

(normal

operation)

Flashing:

Overheat

(battery)

Indicates operation has

been halted due to motor

or battery overheating.

Before the use of LED light,

always pull the power switch

once.

Press the LED light

button.

The light illuminates with

very low current, and it does

not adversely affect the

performance of the tool

during use or its battery

capacity.

[Battery Pack]

For Appropriate Use of

Battery pack

Li-ion Battery pack

• For optimum battery life, store the

Li-ion battery pack following use

without charging it.

• When charging the battery pack,

confirm that the terminals on the

battery charger are free of foreign

substances such as dust and water

etc. Clean the terminals before

charging the battery pack if any for-

eign substances are found on the

terminals.

The life of the battery pack terminals

may be affected by foreign sub-

stances such as dust and water etc.

during operation.

• When battery pack is not in use,

keep it away from other metal ob-

jects like: paper clips, coins, keys,

nails, screws, or other small metal

objects that can make a connection

from one terminal to another.

Shorting the battery terminals to-

gether may cause sparks, burns or a

fire.

• When operating the battery pack,

make sure the work place is well

ventilated.

• When the battery pack is removed

from the main body of the tool, re-

place the battery pack cover imme-

diately in order to prevent dust or dirt

from contaminating the battery ter-

minals and causing a short circuit.

Battery Pack Life

The rechargeable batteries have a

limited life. If the operation time be-

comes extremely short after re-

charging, replace the battery pack

with a new one.

Battery Recycling

ATTENTION:

For environmental protection and

recycling of materials, be sure that

it is disposed of at an officially as-

signed location, if there is one in

your country.

[Battery Charger]

Charging

Cautions

• If the temperature of the battery pack

falls approximately below í10°C

(14°F), charging will automatically

stop to prevent degradation of the

battery.

• The ambient temperature range is

between 0°C (32°F) and 40°C (104°F).

If the battery pack is used when the

battery temperature is below 0°C (32°F),

the tool may fail to function properly.

• When charging a cool battery pack

(below 0°C (32°F)) in a warm place,

leave the battery pack at the place

and wait for more than one hour to

warm up the battery to the level of

the ambient temperature.

• Cool down the charger when charg-

ing more than two battery packs

consecutively.

• Do not insert your fingers into con-

tact hole, when holding charger or

any other occasions.

To prevent the risk of fire or damage to

the battery charger.

• Do not use power source from an en-

gine generator.

• Do not cover vent holes on the charger

and the battery pack.

• Unplug the charger when not in use.

EY7442_7450_7950(EU).indb 10 2011-3-1 11:33:58

-

11

-

(1) LED light

CAUTION:

• The built-in LED light is designed to

illuminate the small work area tempo-

rarily.

• Do not use it as a substitute for a reg-

ular flashlight, since it does not have

enough brightness.

• LED light turns off when the tool has

not been used for 5 minutes.

Caution: DO NOT STARE INTO BEAM.

Use of controls or adjustments or

performance of procedures other than

those specified herein may result in

hazardous radiation exposure.

(2) Overheat warning lamp

To protect the motor or battery, be

sure to note the following when car-

rying out this operation.

• If the motor or battery becomes hot,

the protection function will be acti-

vated and the motor or battery will

stop operating. The overheat warn-

ing lamp on the control panel illumi-

nates or flashes when this feature is

active.

• If the overheating protection feature

activates, allow the tool to cool tho-

roughly (at least 30 minutes). The

tool is ready for use when the over-

heat warning lamp goes out.

• Avoid using the tool in a way that

causes the overheating protection

feature to activate repeatedly.

• If the tool is operated continuously

under high-load conditions or if it is

used in hot-temperature conditions

(such as during summer), the over-

heating protection feature may acti-

vate frequently.

• If the tool is used in cold-temperature

conditions (such as during winter) or

if it is frequently stopped during use,

the overheating protection feature

may not activate.

• The performance of the EY9L42 de-

teriorates significantly at and below

10°C due to work conditions and

other factors.

(3) Battery low warning lamp

Excessive (complete) discharging of

lithium ion batteries shortens their

service life dramatically. The driver

includes a battery protection feature

designed to prevent excessive dis-

charging of the battery pack.

• The battery protection feature acti-

vates immediately before the battery

loses its charge, causing the battery

low warning lamp to flash.

• If you notice the battery low warning

lamp flashing, charge the battery

pack immediately.

Off

(normal

operation)

Flashing

(No charge)

Battery protection

feature active

Off

(normal

operation)

Flashing:

Overheat

(battery)

Indicates operation has

been halted due to motor

or battery overheating.

Before the use of LED light,

always pull the power switch

once.

Press the LED light

button.

The light illuminates with

very low current, and it does

not adversely affect the

performance of the tool

during use or its battery

capacity.

[Battery Pack]

For Appropriate Use of

Battery pack

Li-ion Battery pack

• For optimum battery life, store the

Li-ion battery pack following use

without charging it.

• When charging the battery pack,

confirm that the terminals on the

battery charger are free of foreign

substances such as dust and water

etc. Clean the terminals before

charging the battery pack if any for-

eign substances are found on the

terminals.

The life of the battery pack terminals

may be affected by foreign sub-

stances such as dust and water etc.

during operation.

• When battery pack is not in use,

keep it away from other metal ob-

jects like: paper clips, coins, keys,

nails, screws, or other small metal

objects that can make a connection

from one terminal to another.

Shorting the battery terminals to-

gether may cause sparks, burns or a

fire.

• When operating the battery pack,

make sure the work place is well

ventilated.

• When the battery pack is removed

from the main body of the tool, re-

place the battery pack cover imme-

diately in order to prevent dust or dirt

from contaminating the battery ter-

minals and causing a short circuit.

Battery Pack Life

The rechargeable batteries have a

limited life. If the operation time be-

comes extremely short after re-

charging, replace the battery pack

with a new one.

Battery Recycling

ATTENTION:

For environmental protection and

recycling of materials, be sure that

it is disposed of at an officially as-

signed location, if there is one in

your country.

[Battery Charger]

Charging

Cautions

• If the temperature of the battery pack

falls approximately below í10°C

(14°F), charging will automatically

stop to prevent degradation of the

battery.

• The ambient temperature range is

between 0°C (32°F) and 40°C (104°F).

If the battery pack is used when the

battery temperature is below 0°C (32°F),

the tool may fail to function properly.

• When charging a cool battery pack

(below 0°C (32°F)) in a warm place,

leave the battery pack at the place

and wait for more than one hour to

warm up the battery to the level of

the ambient temperature.

• Cool down the charger when charg-

ing more than two battery packs

consecutively.

• Do not insert your fingers into con-

tact hole, when holding charger or

any other occasions.

To prevent the risk of fire or damage to

the battery charger.

• Do not use power source from an en-

gine generator.

• Do not cover vent holes on the charger

and the battery pack.

• Unplug the charger when not in use.

EY7442_7450_7950(EU).indb 11 2011-3-1 11:33:58

-

12

-

Li-ion Battery Pack

NOTE:

Your battery pack is not fully

charged at the time of purchase.

Be sure to charge the battery be-

fore use.

Battery charger

1. Plug the charger into the AC outlet.

2. Insert the battery pack firmly into the

charger.

1. Line up the alignment marks and

place the battery onto the dock on

the charger.

2. Slide forward in the direction of the

arrow.

3. During charging, the charging lamp

will be lit.

When charging is completed, an in-

ternal electronic switch will auto-

matically be triggered to prevent

overcharging.

•

Charging will not start if the battery

pack is warm (for example, immedi-

ately after heavy-duty operation).

The orange standby lamp will be

flashing until the battery cools down.

Charging will then begin automati-

cally.

4. The charge lamp (green) will flash

slowly once the battery is approxi-

mately 80% charged.

5. When charging is completed, the

charging lamp in green color will turn

off.

6. If the temperature of the battery pack

is 0°C or less, charging takes longer

to fully charge the battery pack than

the standard charging time.

Even when the battery is fully charged,

it will have approximately 50% of the

power of a fully charged battery at

normal operating temperature.

7. Consult an authorized dealer if the

charging lamp (green) does not turn

off.

8. If a fully charged battery pack is in-

serted into the charger again, the

charging lamp lights up. After several

minutes, the charging lamp in green

color will turn off.

9. Remove the battery pack while the

battery pack release button is held up.

A

lignment marks

Battery pack

release button

LAMP INDICATIONS

Charging is completed. (Full charge.)

Battery is approximately 80% charged.

Now charging.

Charger is plugged into the AC outlet. Ready to charge.

(Green) (Orange)

Charging Status Lamp.

Left: green Right: orange will be displayed.

Battery pack is cool.

The battery pack is being charged slowly to reduce the load on the battery.

Battery pack is warm.

Charging will begin when temperature of battery pack drops. If the temperature of the

battery pack is -10° or less, the charging status lamp (orange) will also start flashing.

Charging will begin when the temperature of the battery pack goes up"

Charging is not possible. Clogged with dust or malfunction of the bat-

tery pack.

Turn off Lit Flashing

Information for Users on Collection and Disposal of Old

Equipment and used Batteries

These symbols on the products, packaging, and/or accompanying

documents mean that used electrical and electronic products and

batteries should not be mixed with general household waste.

For proper treatment, recovery and recycling of old products and used

batteries, please take them to applicable collection points, in

accordance with your national legislation and the Directives 2002/96/EC

and 2006/66/EC.

By disposing of these products and batteries correctly, you will help to

save valuable resources and prevent any potential negative effects on

human health and the environment which could otherwise arise from

inappropriate waste handling.

For more information about collection and recycling of old products and

batteries, please contact your local municipality, your waste disposal

service or the point of sale where you purchased the items.

Penalties may be applicable for incorrect disposal of this waste, in

accordance with national legislation.

EY7442_7450_7950(EU).indb 12 2011-3-1 11:33:58

-

13

-

Li-ion Battery Pack

NOTE:

Your battery pack is not fully

charged at the time of purchase.

Be sure to charge the battery be-

fore use.

Battery charger

1. Plug the charger into the AC outlet.

2. Insert the battery pack firmly into the

charger.

1. Line up the alignment marks and

place the battery onto the dock on

the charger.

2. Slide forward in the direction of the

arrow.

3. During charging, the charging lamp

will be lit.

When charging is completed, an in-

ternal electronic switch will auto-

matically be triggered to prevent

overcharging.

•

Charging will not start if the battery

pack is warm (for example, immedi-

ately after heavy-duty operation).

The orange standby lamp will be

flashing until the battery cools down.

Charging will then begin automati-

cally.

4. The charge lamp (green) will flash

slowly once the battery is approxi-

mately 80% charged.

5. When charging is completed, the

charging lamp in green color will turn

off.

6. If the temperature of the battery pack

is 0°C or less, charging takes longer

to fully charge the battery pack than

the standard charging time.

Even when the battery is fully charged,

it will have approximately 50% of the

power of a fully charged battery at

normal operating temperature.

7. Consult an authorized dealer if the

charging lamp (green) does not turn

off.

8. If a fully charged battery pack is in-

serted into the charger again, the

charging lamp lights up. After several

minutes, the charging lamp in green

color will turn off.

9. Remove the battery pack while the

battery pack release button is held up.

A

lignment marks

Battery pack

release button

LAMP INDICATIONS

Charging is completed. (Full charge.)

Battery is approximately 80% charged.

Now charging.

Charger is plugged into the AC outlet. Ready to charge.

(Green) (Orange)

Charging Status Lamp.

Left: green Right: orange will be displayed.

Battery pack is cool.

The battery pack is being charged slowly to reduce the load on the battery.

Battery pack is warm.

Charging will begin when temperature of battery pack drops. If the temperature of the

battery pack is -10° or less, the charging status lamp (orange) will also start flashing.

Charging will begin when the temperature of the battery pack goes up"

Charging is not possible. Clogged with dust or malfunction of the bat-

tery pack.

Turn off Lit Flashing

Information for Users on Collection and Disposal of Old

Equipment and used Batteries

These symbols on the products, packaging, and/or accompanying

documents mean that used electrical and electronic products and

batteries should not be mixed with general household waste.

For proper treatment, recovery and recycling of old products and used

batteries, please take them to applicable collection points, in

accordance with your national legislation and the Directives 2002/96/EC

and 2006/66/EC.

By disposing of these products and batteries correctly, you will help to

save valuable resources and prevent any potential negative effects on

human health and the environment which could otherwise arise from

inappropriate waste handling.

For more information about collection and recycling of old products and

batteries, please contact your local municipality, your waste disposal

service or the point of sale where you purchased the items.

Penalties may be applicable for incorrect disposal of this waste, in

accordance with national legislation.

EY7442_7450_7950(EU).indb 13 2011-3-1 11:33:58

-

14

-

For business users in the European Union

If you wish to discard electrical and electronic equipment, please contact your

dealer or supplier for further information.

[Information on Disposal in other Countries outside the Euro-

pean Union]

These symbols are only valid in the European Union. If you wish to discard these

items, please contact your local authorities or dealer and ask for the correct method

of disposal.

Note for the battery symbol (bottom two symbol examples):

This symbol might be used in combination with a chemical symbol. In this case it

complies with the requirement set by the Directive for the chemical involved.

V. MAINTENANCE

• Use only a dry, soft cloth for wiping the unit. Do not use a damp cloth, thinner,

benzine, or other volatile solvents for cleaning.

• In the event that the inside of the tool or battery pack is exposed to water, drain and

allow to dry as soon as possible. Carefully remove any dust or iron filings that col-

lect inside the tool. If you experience any problems operating the tool, consult with a

repair shop.

VI. ACCESSORIES

Use only bits suitable for size of drill's chuck.

VII. APPENDIX

MAXIMUM RECOMMENDED CAPACITIES

Model EY7442 EY7450 EY7950

Machine screw M8 Screw

driving

Wood screw ø 10 mm or ø 6.8 mm

Self-drilling screw ø 6 mm

For Wood ø 36 mm

For Metal ø 13 mm

Drilling

For Masonry ø 13 mm

VIII. SPECIFICATIONS

MAIN UNIT

Model EY7442 EY7450 EY7950

Motor



voltage 14.4 V 18 V

Low 0 – 410 min

-1

0 – 430 min

-1

No load speed

High 0 – 1530 min

-1

0 – 1650 min

-1

Low ʊ 1800 – 7740 min

-1

Blows Rate Per Minute

High ʊ 6840 – 29700 min

-1

Chuck capacity ø 1.5 mm – ø 13 mm (1/16 – 1/2)

Clutch torque Approx 1.0 N·m – 6.9 N·m

Overall length 218 mm (8-9/16Ǝ) 218 mm (8-9/16Ǝ) 235 mm (9-1/4Ǝ)

Weight (with battery pack) 2.05 k

g

(4.5 lbs) 2.15 k

g

(4.7 lbs) 2.3 k

g

(5.0 lbs)

BATTERY PACK

Model

EY9L41 EY9L42 EY9L44 EY9L50

Storage battery

Li-ion

Battery voltage

14.4V DC

(3.6V X 4 cells)

14.4V DC

(3.6V X 8 cells)

18V DC

(3.6V X 10 cells)

BATTERY CHARGER

Model EY0L81

Electrical rating See the rating plate on the bottom of the charger.

EY9L41 EY9L42 EY9L44 EY9L50

Charging time

Usable:45min

Full:60 min

Usable:30min

Full:35 min

Usable:50 min

Full:65 min

NOTE: This chart may include models that are not available in your area.

Please refer to the latest general catalogue.

NOTE: For the dealer name and address, please see the included warranty card.

EY7442_7450_7950(EU).indb 14 2011-3-1 11:33:58

-

15

-

For business users in the European Union

If you wish to discard electrical and electronic equipment, please contact your

dealer or supplier for further information.

[Information on Disposal in other Countries outside the Euro-

pean Union]

These symbols are only valid in the European Union. If you wish to discard these

items, please contact your local authorities or dealer and ask for the correct method

of disposal.

Note for the battery symbol (bottom two symbol examples):

This symbol might be used in combination with a chemical symbol. In this case it

complies with the requirement set by the Directive for the chemical involved.

V. MAINTENANCE

• Use only a dry, soft cloth for wiping the unit. Do not use a damp cloth, thinner,

benzine, or other volatile solvents for cleaning.

• In the event that the inside of the tool or battery pack is exposed to water, drain and

allow to dry as soon as possible. Carefully remove any dust or iron filings that col-

lect inside the tool. If you experience any problems operating the tool, consult with a

repair shop.

VI. ACCESSORIES

Use only bits suitable for size of drill's chuck.

VII. APPENDIX

MAXIMUM RECOMMENDED CAPACITIES

Model EY7442 EY7450 EY7950

Machine screw M8 Screw

driving

Wood screw ø 10 mm or ø 6.8 mm

Self-drilling screw ø 6 mm

For Wood ø 36 mm

For Metal ø 13 mm

Drilling

For Masonry ø 13 mm

VIII. SPECIFICATIONS

MAIN UNIT

Model EY7442 EY7450 EY7950

Motor



voltage 14.4 V 18 V

Low 0 – 410 min

-1

0 – 430 min

-1

No load speed

High 0 – 1530 min

-1

0 – 1650 min

-1

Low ʊ 1800 – 7740 min

-1

Blows Rate Per Minute

High ʊ 6840 – 29700 min

-1

Chuck capacity ø 1.5 mm – ø 13 mm (1/16 – 1/2)

Clutch torque Approx 1.0 N·m – 6.9 N·m

Overall length 218 mm (8-9/16Ǝ) 218 mm (8-9/16Ǝ) 235 mm (9-1/4Ǝ)

Weight (with battery pack) 2.05 k

g

(4.5 lbs) 2.15 k

g

(4.7 lbs) 2.3 k

g

(5.0 lbs)

BATTERY PACK

Model

EY9L41 EY9L42 EY9L44 EY9L50

Storage battery

Li-ion

Battery voltage

14.4V DC

(3.6V X 4 cells)

14.4V DC

(3.6V X 8 cells)

18V DC

(3.6V X 10 cells)

BATTERY CHARGER

Model EY0L81

Electrical rating See the rating plate on the bottom of the charger.

EY9L41 EY9L42 EY9L44 EY9L50

Charging time

Usable:45min

Full:60 min

Usable:30min

Full:35 min

Usable:50 min

Full:65 min

NOTE: This chart may include models that are not available in your area.

Please refer to the latest general catalogue.

NOTE: For the dealer name and address, please see the included warranty card.

EY7442_7450_7950(EU).indb 15 2011-3-1 11:33:59

-

16

-

IX. ELECTRICAL

PLUG INFOR-

MATION

FOR YOUR SAFETY PLEASE READ

THE FOLLOWING TEXT CAREFULLY

This appliance is supplied with a moulded

three pin mains plug for your safety and

convenience.

A 5 amp fuse is fitted in this plug.

Should the fuse need to be replaced please

ensure that the replacement fuse has a rating

of 5 amp and that it is approved by ASTA or

BSI to BS1362.

Check for the ASTA mark

or the BSI mark

on the body of the fuse.

If the plug contains a removable fuse cover

you must ensure that it is refitted when the

fuse is replaced.

If you lose the fuse cover the plug must not

be used until a replacement cover is ob-

tained.

A replacement fuse cover can be purchased

from your local Panasonic Dealer.

IF THE FITTED MOULDED PLUG IS UN-

SUITABLE FOR THE SOCKET OUTLET IN

YOUR HOME THEN THE FUSE SHOULD

BE REMOVED AND THE PLUG CUT OFF

AND DISPOSED OF SAFELY.

THERE IS A DANGER OF SEVERE

ELECTRICAL SHOCK IF THE CUT OFF

PLUG IS INSERTED INTO ANY 13 AMP

SOCKET.

If a new plug is to be fitted please observe

the wiring code as shown below.

If in any doubt please consult a qualified

electrician.

IMPORTANT:

The wires in this mains lead are co-

loured in accordance with the fol-

lowing code:

Blue: Neutral

Brown: Live

As the colours of the wire in the mains lead of

this appliance may not correspond with the

coloured markings identifying the terminals in

your plug, proceed as follows.

The wire which is coloured BLUE must be

connected to the terminal in the plug which

is marked with the letter N or coloured

BLACK.

The wire which is coloured BROWN must be

connected to the terminal in the plug which is

marked with the letter L or coloured RED.

Under no circumstances should either of

these wires be connected to the earth termi-

nal of the three pin plug, marked with the

letter E or the Earth Symbol

.

How to replace the fuse:

Open the fuse

compartment with a screwdriver and replace

the fuse and fuse cover if it is removable.

ONLY FOR U. K.

Fuse Cover

Original-Anleitung: Englisch

Übersetzung der Original-Anleitung:

Andere Sprachen

Dieses Werkzeug, als komplette Einheit mit

einem Akku, erfüllt die entsprechenden IP-

Schutzgrade auf der Basis der IEC-Vorschriften.

Definition des IP-Codes

IP5X: Staubeintritt wird nicht vollständig

verhütet, aber Staub darf nicht in einer

Menge eindringen, die den zufrieden stel-

lenden Betrieb des Werkzeugs beein-

trächtigt oder die Sicherheit gefährdet (Für

den Fall, dass Talkumpuder unter 75 μm

in das Werkzeug eindringt).

IPX6: Wasser, das durch kräftige Düsen

aus allen Richtungen gegen das Werkzeug

gespritzt wird, darf keine schädlichen

Auswirkungen haben (Für den Fall, dass

eine Wassermenge von ca. 100 L/min mit

normaler Temperatur aus 3 m Entfernung

3 Minuten lang durch eine Düse von 12,5

mm Innendurchmesser in das Werkzeug

injiziert wird).

EINGESCHRÄNKTE GARANTIE

Die Schutzart IP56 qualifiziert diese

Maschine für minimale Auswirkung von

Wasser oder Staub, aber nicht für die

Zusicherung der Leistung unter solchen

Bedingungen. Weitere Einzelheiten zur

Funktionstüchtigkeit finden Sie in den

Sicherheits- und Gebrauchsanweisungen.

Lesen Sie bitte vor der ersten Inbetriebnah-

me dieses Gerätes das separate Handbuch

„Sicherheitsmaßregeln“ sorgfältig durch.

I.

BESTIMMUNGSGEMÄSSE

VERWENDUNG DER

MASCHINE

Diese Werkzeuge können zum

Festziehen der Schrauben im

Kupplungsmodus und zum Bohren

von Löchern in Holz und Metall im

Bohrmodus verwendet werden. Mit

dem Modell EY7950 lassen sich

außerdem im Hammermodus Löcher

in weichen Beton oder ähnliche

Materialien bohren.

Lesen Sie bitte vor der ersten

Inbetriebnahme dieses Gerätes das

separate Handbuch „Sicherheitsmaß-

regeln“ sorgfältig durch.

II.

WEITERE WICHTIGE

SICHERHEITSREGELN

1)

Geeigneten Gehörschutz tragen.

Lärmeinwirkung kann zu Gehörver-

lust führen.

2)

Verwenden Sie den mit dem

Werkzeug gelieferten Zusatzgriff.

Verlust der Kontrolle kann Verlet-

zungen verursachen.

3)

Halten Sie Elektrowerkzeuge an

den isolierten Griffflächen, wenn

Sie eine Arbeit durchführen, bei

der die Maschine auf verborgene

Kabel treffen könnte

; bei Kontakt

mit stromführenden Kabeln werden

die freiliegenden Metallteile der

Maschine ebenfalls stromführend

und der Benutzer erleidet einen

elektrischen Schlag.

4) Tragen Sie eine Staubmaske, falls

bei der Arbeit Staub anfällt.

5) Denken Sie daran, dass das

Werkzeug ständig betriebsbereit ist,

da es nicht an die Steckdose

angeschlossen werden muss.

6) Beim Bohren oder Schrauben in

Wände, Fußböden usw. können

stromführende Kabel berührt werden.

DAHER NIE DAS SCHNELLSPANN-

FUTTER ODER ANDERE VORDERE

METALLTEILE BERÜHREN! Das

Werkzeug beim Schrauben nur am

Kunststoffgriff halten, um in solchen

Fällen vor elektrischen Schlägen

geschützt zu sein.

7) Falls das Bit stecken bleibt, lassen

Sie sofort den Elektronikschalter los,

um eine Überlastung zu verhüten,

die den Akku oder Motor

beschädigen kann.

Verwenden Sie die Rückwärtsdre-

hung, um klemmende Bits zu lösen.

8) Betätigen Sie den Rechts-/Linkslauf-

Umschalthebel NICHT, wenn der

Hauptschalter eingeschaltet ist. Der

Akku entlädt sich sonst schnell, und

das Gerät kann beschädigt werden.

9) Beim Aufladen kann sich das

Lade-gerät etwas erhitzen. Dies ist

normal. Den Akku daher NICHT

über lange Zeit aufladen.

EY7442_7450_7950(EU).indb 16 2011-3-1 11:33:59

-

17

-

IX. ELECTRICAL

PLUG INFOR-

MATION

FOR YOUR SAFETY PLEASE READ

THE FOLLOWING TEXT CAREFULLY

This appliance is supplied with a moulded

three pin mains plug for your safety and

convenience.

A 5 amp fuse is fitted in this plug.

Should the fuse need to be replaced please

ensure that the replacement fuse has a rating

of 5 amp and that it is approved by ASTA or

BSI to BS1362.

Check for the ASTA mark

or the BSI mark

on the body of the fuse.

If the plug contains a removable fuse cover

you must ensure that it is refitted when the

fuse is replaced.

If you lose the fuse cover the plug must not

be used until a replacement cover is ob-

tained.

A replacement fuse cover can be purchased

from your local Panasonic Dealer.

IF THE FITTED MOULDED PLUG IS UN-

SUITABLE FOR THE SOCKET OUTLET IN

YOUR HOME THEN THE FUSE SHOULD

BE REMOVED AND THE PLUG CUT OFF

AND DISPOSED OF SAFELY.

THERE IS A DANGER OF SEVERE

ELECTRICAL SHOCK IF THE CUT OFF

PLUG IS INSERTED INTO ANY 13 AMP

SOCKET.

If a new plug is to be fitted please observe

the wiring code as shown below.

If in any doubt please consult a qualified

electrician.

IMPORTANT:

The wires in this mains lead are co-

loured in accordance with the fol-

lowing code:

Blue: Neutral

Brown: Live

As the colours of the wire in the mains lead of

this appliance may not correspond with the

coloured markings identifying the terminals in

your plug, proceed as follows.

The wire which is coloured BLUE must be

connected to the terminal in the plug which

is marked with the letter N or coloured

BLACK.

The wire which is coloured BROWN must be

connected to the terminal in the plug which is

marked with the letter L or coloured RED.

Under no circumstances should either of

these wires be connected to the earth termi-

nal of the three pin plug, marked with the

letter E or the Earth Symbol

.

How to replace the fuse:

Open the fuse

compartment with a screwdriver and replace

the fuse and fuse cover if it is removable.

ONLY FOR U. K.

Fuse Cover

Original-Anleitung: Englisch

Übersetzung der Original-Anleitung:

Andere Sprachen

Dieses Werkzeug, als komplette Einheit mit

einem Akku, erfüllt die entsprechenden IP-

Schutzgrade auf der Basis der IEC-Vorschriften.

Definition des IP-Codes

IP5X: Staubeintritt wird nicht vollständig

verhütet, aber Staub darf nicht in einer

Menge eindringen, die den zufrieden stel-

lenden Betrieb des Werkzeugs beein-

trächtigt oder die Sicherheit gefährdet (Für

den Fall, dass Talkumpuder unter 75 μm

in das Werkzeug eindringt).

IPX6: Wasser, das durch kräftige Düsen

aus allen Richtungen gegen das Werkzeug

gespritzt wird, darf keine schädlichen

Auswirkungen haben (Für den Fall, dass

eine Wassermenge von ca. 100 L/min mit

normaler Temperatur aus 3 m Entfernung

3 Minuten lang durch eine Düse von 12,5

mm Innendurchmesser in das Werkzeug

injiziert wird).

EINGESCHRÄNKTE GARANTIE

Die Schutzart IP56 qualifiziert diese

Maschine für minimale Auswirkung von

Wasser oder Staub, aber nicht für die

Zusicherung der Leistung unter solchen

Bedingungen. Weitere Einzelheiten zur

Funktionstüchtigkeit finden Sie in den

Sicherheits- und Gebrauchsanweisungen.

Lesen Sie bitte vor der ersten Inbetriebnah-

me dieses Gerätes das separate Handbuch

„Sicherheitsmaßregeln“ sorgfältig durch.

I.

BESTIMMUNGSGEMÄSSE

VERWENDUNG DER

MASCHINE

Diese Werkzeuge können zum

Festziehen der Schrauben im

Kupplungsmodus und zum Bohren

von Löchern in Holz und Metall im

Bohrmodus verwendet werden. Mit

dem Modell EY7950 lassen sich

außerdem im Hammermodus Löcher

in weichen Beton oder ähnliche

Materialien bohren.

Lesen Sie bitte vor der ersten

Inbetriebnahme dieses Gerätes das

separate Handbuch „Sicherheitsmaß-

regeln“ sorgfältig durch.

II.

WEITERE WICHTIGE

SICHERHEITSREGELN

1)

Geeigneten Gehörschutz tragen.

Lärmeinwirkung kann zu Gehörver-

lust führen.

2)

Verwenden Sie den mit dem

Werkzeug gelieferten Zusatzgriff.

Verlust der Kontrolle kann Verlet-

zungen verursachen.

3)

Halten Sie Elektrowerkzeuge an

den isolierten Griffflächen, wenn

Sie eine Arbeit durchführen, bei

der die Maschine auf verborgene

Kabel treffen könnte

; bei Kontakt

mit stromführenden Kabeln werden

die freiliegenden Metallteile der

Maschine ebenfalls stromführend

und der Benutzer erleidet einen

elektrischen Schlag.

4) Tragen Sie eine Staubmaske, falls

bei der Arbeit Staub anfällt.

5) Denken Sie daran, dass das

Werkzeug ständig betriebsbereit ist,

da es nicht an die Steckdose

angeschlossen werden muss.

6) Beim Bohren oder Schrauben in

Wände, Fußböden usw. können

stromführende Kabel berührt werden.

DAHER NIE DAS SCHNELLSPANN-

FUTTER ODER ANDERE VORDERE

METALLTEILE BERÜHREN! Das

Werkzeug beim Schrauben nur am

Kunststoffgriff halten, um in solchen

Fällen vor elektrischen Schlägen

geschützt zu sein.

7) Falls das Bit stecken bleibt, lassen

Sie sofort den Elektronikschalter los,

um eine Überlastung zu verhüten,

die den Akku oder Motor

beschädigen kann.

Verwenden Sie die Rückwärtsdre-

hung, um klemmende Bits zu lösen.

8) Betätigen Sie den Rechts-/Linkslauf-

Umschalthebel NICHT, wenn der

Hauptschalter eingeschaltet ist. Der

Akku entlädt sich sonst schnell, und

das Gerät kann beschädigt werden.

9) Beim Aufladen kann sich das

Lade-gerät etwas erhitzen. Dies ist

normal. Den Akku daher NICHT

über lange Zeit aufladen.

EY7442_7450_7950(EU).indb 17 2011-3-1 11:33:59

-

18

-

10) Stellen Sie den Rechts-/Linkslauf-

Umschalthebel zum Lagern oder

Tragen des Werkzeugs auf die

Mittenstellung (Schaltersperre).

11) Belasten Sie das Werkzeug nicht,

indem Sie den Elektronikschalter

halb gedrückt halten (Drehzahlre-

gelmodus), sodass der Motor

stehen bleibt.

12)

Verstellen Sie den Drehzahl-Wahl-

schalter (LOW-HIGH) nicht,

während Sie den Elektronikschalter

betätigen. Dies kann zu schneller

Abnutzung der wiederaufladbaren

Batterie oder zu einer Beschädigung

des internen Motormechanismus

führen.

Symbol Bedeutung

V

Volt

Gleichstrom

n

0

Leerlaufdrehzahl

… min

-1

Drehzahl oder Hubzahl

pro Minute

Ah

Akkukapazitat in Ampere

Stunden

Rechtslauf

Linkslauf

Schlagbohren

Bohren

Zur Verminderung der

Verletzungsgefahr muss

die Bedienungsanleitung

gründlich gelesen

werden.

Nur für Inneneinsatz.

WARNUNG:

• Bitte verwenden Sie für dieses wie-

deraufladbare Gerät nur die von

Panasonic vorgesehenen Akkus.

• Panasonic übernimmt keine

Verantwortung für etwaige Schäden

oder Unfälle, die durch den Ge-

brauch von recycelten und ge-

fälschten Akkus verursacht werden.

• Entsorgen Sie diesen Akku niemals

im Feuer und setzen Sie ihn keines-

falls starker Hitze aus.

• Versuchen Sie niemals, Gegen-

stände wie Nägel in den Akku zu

schlagen, dies könnte zu einem

elektrischen Schlag führen. Sehen

Sie außerdem davon ab, den Akku

zu zerlegen oder zu verändern.

• Achten Sie darauf, dass keine me-

tallischen Gegenstände mit den An-

schlüssen des Akkus in Verbindung

kommen.

• Der Akku darf nicht im selben Be-

hälter wie Nägel oder ähnliche me-

tallische Gegenstände transportiert

oder gelagert werden.

• Laden Sie den Akku niemals an

einem Ort mit hoher Temperatur,

beispielsweise neben einem Feuer

oder direkter Sonneneinstrahlung.

Andernfalls kann dies zu Überhit-

zung, einem Brand oder einer Ex-

plosion führen.

• Laden Sie den Akku ausschließlich

mit dem dafür vorgesehenen Lade-

gerät. Andernfalls kann dies zu

einem Auslaufen des Akkus, einem

Brand oder einer Explosion führen.

• Nachdem Sie den Akku von der

Maschine oder dem Ladegerät

abgenommen haben, bringen Sie

stets die Akkuabdeckung wieder an.

Anderenfalls könnten die

Akkukontakte kurzgeschlossen

werden, was zu einem Brand führen

kann.

• Wenn der Akku schwach geworden

ist, ersetzen Sie ihn durch einen

neuen.

Fortgesetzter Gebrauch eines

beschädigten Akkus kann zu Wär-

meerzeugung, Entzündung oder

Bruch führen.

III. BAUGRUPPE

Anbringen oder Abnehmen

des Bits

HINWEIS:

Trennen Sie vor dem Anbringen oder

Abnehmen eines Bits den Akku vom

Werkzeug ab, oder stellen Sie den

Elektronikschalter auf die Mittelstel-

lung (Schaltersperre).

Dieses Werkzeug ist mit einem schlüs-

sellosen Bohrfutter ausgestattet.

1. Anbringen

Das Bit einführen, und den Knebelring

zum Anziehen im Uhrzeigersinn

drehen (von vorn gesehen), bis das

Klicken aufhört.

Knebelring

2. Abnehmen

Den Knebelring entgegen dem Uhr-

zeigersinn drehen (von vorn ge-

sehen), dann das Bit abnehmen.

HINWEIS:

Wenn starkes Spiel im Futter auf-tritt,

den Bohrer sichern, dann

die

Futterklauen durch Drehen der Sper-

rhülse öffnen und die Schraube

(Linksgewinde) durch Drehen entge-

gen dem Uhrzeigersinn (von vorn

gesehen) mit einem Schraubenzieher

anziehen.

Anbringen oder Abnehmen

des Akkus

1. Zum Anschließen des Akkus:

Die Ausrichtmarkierungen aufein-

ander ausrichten, und den Akku

anbringen.

• Den Akku einschieben, bis er ein-

rastet.

     

2. Zum Entfernen des Akkus:

Zum Abnehmen des Akkus am

Knopf an der Vorderseite ziehen.

Zusatzgriff

Bringen Sie den Zusatzgriff an Ihrer

bevorzugten Position an, und ziehen

Sie den Griff fest an.

Benutzen Sie stets den Stützgriff, um

die Betriebssicherheit zu

gewährleisten.

A

usrichtmarkierungen

Knopf

Festziehen

Lösen

EY7442_7450_7950(EU).indb 18 2011-3-1 11:33:59

-

19

-

10) Stellen Sie den Rechts-/Linkslauf-

Umschalthebel zum Lagern oder

Tragen des Werkzeugs auf die

Mittenstellung (Schaltersperre).

11) Belasten Sie das Werkzeug nicht,

indem Sie den Elektronikschalter

halb gedrückt halten (Drehzahlre-

gelmodus), sodass der Motor

stehen bleibt.

12)

Verstellen Sie den Drehzahl-Wahl-

schalter (LOW-HIGH) nicht,

während Sie den Elektronikschalter

betätigen. Dies kann zu schneller

Abnutzung der wiederaufladbaren

Batterie oder zu einer Beschädigung

des internen Motormechanismus

führen.

Symbol Bedeutung

V

Volt

Gleichstrom

n

0

Leerlaufdrehzahl

… min

-1

Drehzahl oder Hubzahl

pro Minute

Ah

Akkukapazitat in Ampere

Stunden

Rechtslauf

Linkslauf

Schlagbohren

Bohren

Zur Verminderung der

Verletzungsgefahr muss

die Bedienungsanleitung

gründlich gelesen

werden.

Nur für Inneneinsatz.

WARNUNG:

• Bitte verwenden Sie für dieses wie-

deraufladbare Gerät nur die von

Panasonic vorgesehenen Akkus.

• Panasonic übernimmt keine

Verantwortung für etwaige Schäden

oder Unfälle, die durch den Ge-

brauch von recycelten und ge-

fälschten Akkus verursacht werden.

• Entsorgen Sie diesen Akku niemals

im Feuer und setzen Sie ihn keines-

falls starker Hitze aus.

• Versuchen Sie niemals, Gegen-

stände wie Nägel in den Akku zu

schlagen, dies könnte zu einem

elektrischen Schlag führen. Sehen

Sie außerdem davon ab, den Akku

zu zerlegen oder zu verändern.

• Achten Sie darauf, dass keine me-

tallischen Gegenstände mit den An-

schlüssen des Akkus in Verbindung

kommen.

• Der Akku darf nicht im selben Be-

hälter wie Nägel oder ähnliche me-

tallische Gegenstände transportiert

oder gelagert werden.

• Laden Sie den Akku niemals an

einem Ort mit hoher Temperatur,

beispielsweise neben einem Feuer

oder direkter Sonneneinstrahlung.

Andernfalls kann dies zu Überhit-

zung, einem Brand oder einer Ex-

plosion führen.

• Laden Sie den Akku ausschließlich

mit dem dafür vorgesehenen Lade-

gerät. Andernfalls kann dies zu

einem Auslaufen des Akkus, einem

Brand oder einer Explosion führen.

• Nachdem Sie den Akku von der

Maschine oder dem Ladegerät

abgenommen haben, bringen Sie

stets die Akkuabdeckung wieder an.

Anderenfalls könnten die

Akkukontakte kurzgeschlossen

werden, was zu einem Brand führen

kann.

• Wenn der Akku schwach geworden

ist, ersetzen Sie ihn durch einen

neuen.

Fortgesetzter Gebrauch eines

beschädigten Akkus kann zu Wär-

meerzeugung, Entzündung oder

Bruch führen.

III. BAUGRUPPE

Anbringen oder Abnehmen

des Bits

HINWEIS:

Trennen Sie vor dem Anbringen oder

Abnehmen eines Bits den Akku vom

Werkzeug ab, oder stellen Sie den

Elektronikschalter auf die Mittelstel-

lung (Schaltersperre).

Dieses Werkzeug ist mit einem schlüs-

sellosen Bohrfutter ausgestattet.

1. Anbringen

Das Bit einführen, und den Knebelring

zum Anziehen im Uhrzeigersinn

drehen (von vorn gesehen), bis das

Klicken aufhört.

Knebelring

2. Abnehmen

Den Knebelring entgegen dem Uhr-

zeigersinn drehen (von vorn ge-

sehen), dann das Bit abnehmen.

HINWEIS:

Wenn starkes Spiel im Futter auf-tritt,

den Bohrer sichern, dann

die

Futterklauen durch Drehen der Sper-

rhülse öffnen und die Schraube

(Linksgewinde) durch Drehen entge-

gen dem Uhrzeigersinn (von vorn

gesehen) mit einem Schraubenzieher

anziehen.

Anbringen oder Abnehmen

des Akkus

1. Zum Anschließen des Akkus:

Die Ausrichtmarkierungen aufein-

ander ausrichten, und den Akku

anbringen.

• Den Akku einschieben, bis er ein-

rastet.

     

2. Zum Entfernen des Akkus:

Zum Abnehmen des Akkus am

Knopf an der Vorderseite ziehen.

Zusatzgriff

Bringen Sie den Zusatzgriff an Ihrer

bevorzugten Position an, und ziehen

Sie den Griff fest an.

Benutzen Sie stets den Stützgriff, um

die Betriebssicherheit zu

gewährleisten.

A

usrichtmarkierungen

Knopf

Festziehen

Lösen

EY7442_7450_7950(EU).indb 19 2011-3-1 11:33:59

-

20

-

IV. BETRIEB

[Hauptteil]

Schalterfunktion

1. Die Drehzahl erhöht sich, je stärker

der Elektronikschalter gedrückt wird.

Drücken Sie den Elektronikschalter

zu Beginn der Arbeit nur leicht, um

mit langsamer Drehung zu begin-

nen.

2. Ein elektronischer

Feedback-Controller wird verwendet,

um auch bei niedriger Drehzahl ein

starkes Drehmoment zu erhalten.

3. Beim Loslassen des Elektronik-

schalters wird die Bremse betätigt

und der Motor sofort angehalten.

HINWEIS:

• Bei der Betätigung der Bremse kann

ein Bremsgeräusch hörbar sein. Dies

ist normal.

• Beim Umschalten und Bremsen

können wegen der auf den Motor

ausgeübten Belastung Funken von

der Motorbürste durch die

Ventilationsöffnungen im Gehäuse

auf der Rückseite der Maschine

sichtbar sein. Dies ist kein Anzeichen

für eine Störung der Maschine.

Umschalten und Betätigung

des Rechts-/Linkslauf-

Umschalthebels

Rechts Links

Schaltersperre

VORSICHT:

Nicht den Rechts-/Linkslauf- Um-

schalthebel betätigen, bevor der Bit

vollständig zur Ruhe gekommen ist,

um Schäden zu ver-hindern.

Rechtslauf – Schalterbetätigung

1. Für Rechtslauf den Hebel drücken.

2. Drücken Sie den Schalter leicht, um

das Werkzeug langsam zu starten.

3. Die Drehzahl nimmt zu, je stärker der

Elektronikschalter gedrückt wird, um

effizientes Anziehen von Schrauben

und Bohren zu ermöglichen. Beim

Loslassen des Schalters wird die

Bremse betätigt und das Futter sofort

angehalten.

4. Nach der Verwendung den Hebel auf

die Mitten-position zurückstellen

(Schaltersperre).

Linkslauf – Schalterbetätigung

1. Für Linkslauf den Hebel drücken.

Die Drehrichtung vor dem Betrieb

prüfen.

2. Drücken Sie den Schalter leicht, um

das Werkzeug langsam zu starten.

3. Nach der Verwendung den Hebel

auf die Mitten-position zurückstellen

(Schaltersperre).

Einstellung des Kupplungs-

drehmoments

Stellen Sie das Drehmoment auf eine

der 18 Kupplungsstufen oder die Posi-

tion „ “ ein (EY7442, EY7450).

Stellen Sie das Drehmoment auf eine

der 18 Kupplungsstufen oder die Posi-

tion „

“„ “, ein (EY7950).

HINWEIS:

Schalten Sie stets die Maschine aus

und nehmen Sie sie vom Werkstück

ab, wenn Sie durch Drehen des

Kupplungsgriffs vom Bohrmodus auf

den Schlagbohrmodus oder

umgekehrt umschalten.

VORSICHT:



ԘWenn der Kupplungsgriff nach dem

Bohren mit Kupplungsfunktion nicht

auf den Modus „Bohren“ oder

„Hämmern“ eingestellt werden kann,

stellen Sie den Kupplungsgriff auf

Position 1, und betreiben Sie die

Kupplung eine Sekunde lang.

Wahl der Drehzahl

Wählen Sie je nach der Arbeit eine

niedrige oder hohe Drehzahl.

Je weiter der stufenlose Elektro-

nikschalter hineingedrückt wird, desto

höher wird die Drehzahl.

WARNUNG:

• Atmen Sie keinen Rauch ein, der von

der Maschine oder dem Akku abgege-

ben wird, weil er gesundheitsschädlich

sein kann.

VORSICHT:

• Überprüfen Sie den Drehzahl-Wahl-

schalter vor Gebrauch.

• Verwenden Sie eine niedrige

Drehzahl, wenn eine große Kraft bei

der Arbeit erforderlich ist. (Die

Verwendung einer hohen Drehzahl

bei Ausübung einer großen Kraft

kann zu einer Beschädigung des

Motors führen.)

•

Verwenden Sie das Werkzeug nie so,

dass der Motor arretiert wird.

Anderenfalls kann das Werkzeug

oder Akkupack beschädigt werden,

und es kann zu Rauchentwicklung

oder einem Brand kommen.

• Verstellen Sie den Drehzahl-Wahl-

schalter (LOW-HIGH) nicht, während

Sie den Elektronikschalter betätigen.

Dies kann zu schneller Abnutzung

der wiederaufladbaren Batterie oder

zu einer Beschädigung des internen

Motormechanismus führen.

* Siehe die technischen Daten für

„MAXIMAL ZULÄSSIGE KAPAZI-

TÄTEN“.

VORSICHT:

• Um übermäßigen Temperaturanstieg

der Werkzeugoberfläche zu

vermeiden, sollte das Werkzeug

nicht kontinuierlich mit zwei oder

mehr Akkus betrieben werden. Das

Werkzeug muss vor dem Akku-

wechsel abkühlen.

• Blockieren Sie nicht die Ventilations-

öffnungen an den Seiten des

Gehäuses während des Betriebs.

Anderenfalls wird die Maschinen-

funktion beeinträchtigt, was zu einem

Ausfall führen kann.

• Belasten Sie das Werkzeug (den

Motor) NICHT übermäßig. Es kann

sonst zu einer Beschädigung der

Maschine kommen.

• Halten Sie die Maschine so, dass die

Abluft von den Ventilations-

öffnungen im Gehäuse nicht direkt

auf Ihre Haut bläst. Anderenfalls

können Sie sich verbrennen.

Bitverriegelungsfunktion

1. Wenn der Elektronikschalter bei

eingesetztem Schraubendreherbit

ausgerückt ist, kann das Werkzeug

wie ein manueller Schraubendreher

verwendet werden (bis zu 40 N·m,

408 kgf·cm, 353 in-lbs).

Es kann etwas Spiel im Futter

vor-handen sein, was jedoch keine

Funk-tionsstörung ist.

HOCH

NIEDRIG

Stellen Sie die Kupplungseinstellung vor dem

tatsächlichen Betrieb auf dieses Zeichen (

).

EY7442_7450_7950(EU).indb 20 2011-3-1 11:34:00

Sidan laddas ...

Panasonic EY7442 Bruksanvisning

Panasonic EY7442 Bruksanvisning

på andra språk

Relaterade papper

Andra dokument