5
Replacement kit - Jet Swim Athlete
MA30-15 GB
ENGLISH
8 pcs
Detta dokument och dess innehåll ägs
av Pahlén AB och får ej kopieras, delas
eller vidarebefordras till tredjepart utan
skriftlig godkännande.
Art.no.
Revision
Sheet size
Drawing number
Unit E
A3
mm
Jet Swim Athlete instruktion
M20788 0
3D-model
M20788-0
Designed by
RJ 2022-03-03 3 (3)
Side of
Date of issue
Unless otherwise stated:
All dimensions are after
surface treatment.
Tolerances/dimensions in this
document take priority over values
found in 3D-model.
General surface profile tolerance Threads
ISO 965
Edges of undefined
shape ISO 13715
Surface roughness
(Ra) ISO 1302
The 3D-model is correct and made in
the middle of the tolerance zon.
Tolerancing
ISO 8015
-
A
B
Detta dokument och dess innehåll ägs
av Pahlén AB och får ej kopieras, delas
eller vidarebefordras till tredjepart utan
skriftlig godkännande.
Art.no.
Revision
Sheet size
Drawing number
Unit E
A3
mm
Jet Swim Athlete instruktion
M20788 0
3D-model
M20788-0
Designed by
RJ 2022-03-03 1 (3)
Side of
Date of issue
Unless otherwise stated:
All dimensions are after
surface treatment.
Tolerances/dimensions in this
document take priority over values
found in 3D-model.
General surface profile tolerance Threads
ISO 965
Edges of undefined
shape ISO 13715
Surface roughness
(Ra) ISO 1302
The 3D-model is correct and made in
the middle of the tolerance zon.
Tolerancing
ISO 8015
-
2 pcs
C
D
Detta dokument och dess innehåll ägs
av Pahlén AB och får ej kopieras, delas
eller vidarebefordras till tredjepart utan
skriftlig godkännande.
Art.no.
Revision
Sheet size
Drawing number
Unit E
A3
mm
Jet Swim Athlete instruktion
M20788 0
3D-model
M20788-0
Designed by
RJ 2022-03-03 2 (3)
Side of
Date of issue
Unless otherwise stated:
All dimensions are after
surface treatment.
Tolerances/dimensions in this
document take priority over values
found in 3D-model.
General surface profile tolerance Threads
ISO 965
Edges of undefined
shape ISO 13715
Surface roughness
(Ra) ISO 1302
The 3D-model is correct and made in
the middle of the tolerance zon.
Tolerancing
ISO 8015
-
E
D
C
8 pcs
F
G
2
5
2
4
2
1
12223
20 19
1
8
1
7
3
2
5 6 7 8
12
1
4
1
5
1
6
31 30
2
9
2
7
2
8
2
7
2
6
13
1
4 pcs
4 pcs
2
5
2
4
2
1
12223
20 19
1
8
1
7
3
2
5 6 7 8
12
1
4
1
5
1
6
31 30
2
9
2
7
2
8
2
7
2
6
13
1
2
5
2
4
2
1
12223
20 19
1
8
1
7
3
2
5 6 7 8
12
1
4
1
5
1
6
31 30
2
9
2
7
2
8
2
7
2
6
13
1
2
5
2
4
2
1
12223
20 19
1
8
1
7
3
2
5 6 7 8
12
1
4
1
5
1
6
31 30
2
9
2
7
2
8
2
7
2
6
13
1
2
5
2
4
2
1
12223
20 19
1
8
1
7
3
2
5 6 7 8
12
1
4
1
5
1
6
31 30
2
9
2
7
2
8
2
7
2
6
13
1
Product Description
Jet Swim Athlete Replacement Kit. Can be retrotted if necessary.
Pahlén recommends lowering the water level until it is below the Jet Swim Athlete before assembly.
Make sure that the power is disconnected before starting work.
Instructions:
1. Change the front plate:
It is important that you read this manual carefully to secure the function and useful life of the pool equipment.
Pahlén AB is not responsible for product warranty or damage caused by incorrect installation, use or incorrect maintenance.
Unscrew the 8 nuts (C) that hold the parts in
place.
Pull out the entire package as a single unit,
with the nozzle (D), plate (E), ow control (F)
and all included components.
Carefully feed the hose to the start button.
NOTE! The start button must be kept above
the water surface at all times.
3. Fit the new plate:
The start button (6), bellows (7), connection nipple (8) and plate (12)
with gasket are to be reused.
Fit the start button’s components to the new control plate (5).
Fit the plate to the chassis using 4 nuts, 2 Nm tightening torque.
Make sure that the start button’s hose is not risk pinched.
4. Fit the new nozzle:
Change the gasket (2) behind the nozzle. Fit the new nozzle (3) using 4 nuts,
2 Nm tightening torque.
5. Re-t the intake grille and the front.
Put the intake grille in place with even pressure over all of the part until it is in its innermost position.
Fit the front using the 2 screws.
Carefully remove the front frame (A)
and the intake grille (B).
Take them out of the pool.
The screws are to be reused.
Unscrew the small screws (C) on the back of
the intake grille (8 pcs). They are to be reused.
Replace the existing front plate (D) with the
new one and screw it into the intake grille.
2. Dismantle the nozzle and plate: