Sportec FIT 1.0, FIT 3.0, SP 2.0 & SP 4.0 Användarmanual

Instruction for use

Mode d’emploi

Anweisungen

Istruzioni

Instrucciones

Instructies

Instruções

Инструкция

Bruksanvisning

Instruction for use

01

EN

TABLE OF CONTENTS

1. Explanation of symbols 02

2. How does electrostimulation work? 03

3. How does MI (Muscle Intelligence) technology work? 05

4. Device function 06

Contents of kits and accessories 06

Device description 07

Battery insertion 08

Connection 08

Preliminary settings 09

Choosing a category 09

Selecting a programme 10

MI-scan test 11

Adjusting stimulation intensities 11

Programme progression 12

End of a programme 13

Battery level and charging 13

5. Troubleshooting 15

6. Device maintenance 18

7. Technical speciﬁcations 19

8. EMC Table 21

It is strongly recommended to read these instructions and the contra-indications and safety

measures carefully before using your stimulator.

02

EN

1. EXPLANATION OF SYMBOLS

See the instructions

The stimulator is a category II device with built-in power supply and type BF applied parts.

Manufacturer’s name and address and date of manufacture

Name and address of approved representative in the European Union

This device must be separated from household waste and sent to special collection facilities for

recycling and recovery

The stand-by button is multi-functional

Protect from sunlight

Store in a dry place

This is an indication for protection against ingress of water and particulate matter. The mark IP20

on your unit means: your unit is protected against solid foreign objects of 12.5mm dia and greater.

Not protected against water

IP02 on the carrying case means: Protected from the ingress of water droplets from a shower

of rain.

Latex-free

Reference number

Batch number

IP02

on the case

IP20

on the unit

03

EN

2. HOW DOES ELECTROSTIMULATION WORK?

Electrostimulation involves stimulating nerve ﬁbres by electrical impulses transmitted by electrodes. The

electrical impulses produced by Compex stimulators are high-quality impulses that are safe, comfortable

and effective and stimulate various types of nerve ﬁbres:

1. Motor nerves to stimulate a muscular response, referred to as electrical muscle stimulation (EMS).

2. Certain types of sensitive nerve ﬁbres to obtain analgesic effects or pain relief.

1. STIMULATION OF MOTOR NERVES (EMS)

With voluntary activity, the brain orders muscles to contract and a command is then sent to nerve ﬁbres

in the form of an electrical signal. This signal is then sent to muscle ﬁbres, which contract. The principle of

electrostimulation accurately reproduces the process involved in a voluntary contraction. The stimulator

sends an electrical impulse to nerve ﬁbres to excite them. This excitation is then transmitted to muscle

ﬁbres and results in a basic mechanical response (= a twitch). This is the basic requirement for muscular

contraction. The muscular response is to all intents and purposes identical to the muscular work

controlled by the brain. In other words, the muscle does not distinguish between a command sent by the

brain or the stimulator.

Programme settings (number of impulses per second, duration of contraction, rest time, total programme

duration) subject the muscle to various types of work, depending on the muscle ﬁbre. Various types

of muscle ﬁbres can be identiﬁed according to their respective contraction speeds: slow, intermediate

and fast ﬁbres. A sprinter clearly has more fast ﬁbres and a marathon runner has more slow ﬁbres. With

good knowledge of human physiology and full control of stimulation settings of the various programmes,

muscular work can be speciﬁcally pinpointed to achieve the desired objective (muscular strengthening,

increased blood circulation, ﬁrming, etc.).

04

EN

2. STIMULATION OF SENSORY NERVES

Electrical impulses can also excite sensory nerve ﬁbres to obtain analgesic effects or pain relief.

Stimulating tactile sensory nerve ﬁbres blocks pain being transmitted to the nervous system. Stimulating

another type of sensory ﬁbre increases the production of endorphins and therefore reduces pain. With

pain relief programmes, electrostimulation can be used to treat acute or chronic localised pain and

muscle pain.

Caution: Do not use pain relief programmes for an extended period without medical advice.

BENEFITS OF ELECTROSTIMULATION

Electrostimulation is a very effective method for making muscles work:

• With a signiﬁcant improvement in various muscular qualities

• With no cardiovascular or mental fatigue

• With limited stress exerted on joints and tendons. Electrostimulation thereby enables more muscular

work than voluntary activity.

For optimum results, Compex recommends supplementing your electrostimulation sessions with other

commitments, such as:

• Regular physical exercise

• A balanced and healthy diet

• A balanced lifestyle

05

EN

3. HOW DOES MI (MUSCLE INTELLIGENCE)

TECHNOLOGY WORK?

To access MI functions the MI-sensor cable (not available on all devices) must be connected to the stimulator.

MI-SCAN

Just before starting a work session, the MI-scan function probes the chosen muscle group and automatically

adjusts the stimulator settings to the excitability of this area of the body, depending on your physiology.

This function results in a short test sequence at the start of the programme, during which measurements

are taken.

At the end of the test, the intensity has to be increased to start the programme.

MI-TENS

The MI-tens function limits unwanted muscle contractions in painful areas.

With each intensity increase applied by the user, a test phase occurs, and if a muscular contraction is

detected, the device automatically reduces the intensity of the stimulation.

This function is only accessible in the TENS, Epicondylitis and Tendinitis programmes.

MI-RANGE

The MI-range function indicates the ideal range for adjusting stimulation intensity, to be followed in the

following programmes: recovery, massage, capillarisation or even muscle pain.

When the device has detected the ideal intensity range, check mark will appear on the screen. For optimum

work, intensity should be kept within this range.

Not all devices have MI technology. The table below shows which functions are available with each device.

SP 2.0 SP 4.0 FIT 1.0 FIT 3.0

MI-SCAN

✓ ✓

-

✓

MI-TENS -

✓

-

MI-RANGE -

✓

-

06

EN

4. DEVICE FUNCTION

CONTENTS OF KITS AND ACCESSORIES

SP 2.0 SP 4.0 FIT 1.0 FIT 3.0

REF QTY REF QTY REF QTY REF QTY

STIMULATOR 001096 1 001095 1 001098 1 001097 1

CHARGER 6830XX 1 6830XX 1 6830XX 1 6830XX 1

SET OF 4 SNAP CABLES 001119 1 001119 1 001119 1 001119 1

MI-SENSOR CABLE 601160 1 601160 1 N/A N/A 601160 1

BAG OF SMALL 5X5

ELECTRODES

42215 2 42215 2 42215 2 42215 2

BAG OF LARGE 5X10

ELECTRODES

42216 2 42216 2 42216 2 42216 2

INSTRUCTIONS ON

CD-ROM

880053 1 880053 1 880053 1 880053 1

QUICK START GUIDE 885624 1 885624 1 885624 1 885624 1

CARRY CASE 680029 1 680029 1 680029 1 680029 1

BATTERY PACK 94121X 1 94121X 1 94121X 1 94121X 1

Only use this device with cables, electrodes, battery, power adaptor and accessories

recommended by Compex.

07

EN

DEVICE DESCRIPTION

A Standby button

B Sockets for the 4 stimulation cables

C Stimulation cables

D +/- buttons for the 4 stimulation channels

E I-button, which allows:

• The intensities to be increased on several channels at the same time

• The last 5 programmes used to be accessed

F Charger socket (slide the red cover to the right to reveal the charger connector)

G Battery compartment

H Socket for belt clip

A

B

C

DE

F

G

H

08

EN

BATTERY INSERTION

Open the battery compartment cover and insert the battery, with the label pointing upwards so that the +

and - terminals are opposite the device’s contacts. Then replace the cover. If the device is not going to be

used for over 3 months, ensure that the battery is fully charged. If the device is not going to be used for over

6 months, ensure that the battery is fully charged and remove it from the stimulator. Switch the stimulator off

before removing the battery.

CONNECTIONS

CHARGER CONNECTION

Remove all stimulation cables from the stimulator before recharging it. Connect the charger to a wall socket

and connect the stimulator by sliding the red cover to the right to reveal the charger connector. It is strongly

recommended to fully charge the battery before its ﬁrst use to improve its performance and life span.

CONNECTING THE CABLES

The cables of the stimulator connect to the 4 sockets at the front of the device. The MI-sensor cable (if

available with the device) can be connected to any socket on the stimulator.

COMPEX

09

EN

PRELIMINARY SETTINGS

Before your ﬁrst use, you can deﬁne various settings. This options screen can then be displayed by switching

the device off and by pressing and holding the on/off button for at least 2 seconds.

B Press the +/- button of channel 1 to select the language to be used.

C Press the +/- button of channel 2 to adjust screen contrast.

D Use the +/- button of channel 3 to adjust the volume.

E Press the +/- button of channel 4 to adjust the backlighting.

ON: backlighting always active.

OFF: backlighting always inactive.

AUTO: backlighting activated every time a button is pressed.

A Press the on/off button to conﬁrm and save your selections. Settings are immediately applied.

CHOOSING A CATEGORY

N.B. The following screens are generic examples but they work in the same way regardless of the device that

you have.

To switch the stimulator on, brieﬂy press the on/off button.

Before selecting a programme, you should select the desired category.

A Press the on/off button to switch the device off.

B Press the +/- button of channel 1 to select a category.

E Press the +/- button of channel 4 to conﬁrm your selection.

A B C D E

A B E

10

EN

TOP 5

To access the last 5 programmes used press the I-button. From there, select the desired programme and

start it.

SELECTING A PROGRAMME

A Press the on/off button to return to the previous screen.

B Press the +/- button of channel 1 to select a programme.

E Press the +/- button of channel 4 to conﬁrm the selection and start the stimulation session.

N.B. After selecting a programme an additional screen may appear, requesting the programme cycle to be

selected. Select the desired cycle and then press the +/- button of channel 4 to conﬁrm the selection and

start the stimulation session.

It is recommended to start with the 1st cycle and to change cycle when it is complete, normally after 4

to 6 weeks of stimulation based on 3 sessions per week. It is also important to have reached signiﬁcant

stimulation intensities during the sessions before progressing to another cycle.

At the end of the cycle you can either start a new cycle or carry out maintenance training based on one

session per week.

A B E

11

EN

MI-SCAN TEST

N.B. See the chapter “How MI technology works”.

If the MI-sensor cable is connected, the MI-scan test starts immediately after the programme is selected.

A Press the on/off button to stop the test

The +/- buttons of the 4 channels are inactive throughout the test.

ADJUSTING STIMULATION INTENSITIES

When you start a programme, you are asked to increase the stimulation intensities.

This step is essential for a successful session.

1 Programme duration in minutes and seconds

2 Programme progression bar. For details of how it works, see the following paragraph:

“Programme progression”

A Press the on/off button to switch the unit into Pause mode.

B C D E The four channels ﬂash, going from + to 000. The stimulation intensity must be increased to be able

to start stimulation. For this, press the + buttons of the relevant channels until the desired setting is reached.

N.B. To increase the intensities on several channels simultaneously, press the I-button and then increase the

intensities. The interdependent channels are displayed in white on a black background.

A

A B C D E

1

2

12

EN

A B C D E

PROGRAMME PROGRESSION

Stimulation starts properly once the stimulation intensity has been increased.

The examples below explain the general rules. Depending on the programme, there may be slight differences.

1 Time remaining (in minutes and seconds) until the end of a programme

2 The duration bar showing the duration of the contraction and duration of active rest is only shown during

the work sequence

3 Session sequences

4 Warm-up

5 Work period

6 Relaxation

A Press the on/off button to temporarily interrupt the programme. To resume, simply press the +/- button of

channel 4. The session will resume at 80% of the intensity level being used before it was interrupted.

N.B. In pause mode, the button switches directly to the next sequence.

N.B. In pause mode and depending on the programme, usage statistics may be displayed:

MAX = the maximum intensity reached per channel during contraction phases

AVG= the average intensity for all channels applied during the contraction phases

B C D E The various intensities reached during the contraction phase are shown by a series of black vertical

bars; the intensities of the rest phase are illustrated by hatched bars.

Please note that the stimulation intensities for the active rest phase are automatically set to 50% of the

contraction intensities. They can be changed during the rest phase. Once changed, they are completely

independent of the contraction intensities.

1

23

4 5 6

13

EN

END OF A PROGRAMME

At the end of a session, the following screen is displayed. To stop the stimulator, press the on/off button.

N.B. Depending on the programme, usage statistics may be displayed (see previous chapter

“Programme progression”).

BATTERY LEVEL AND CHARGING

Battery performance depends on the programme and the stimulation intensity applied. It is strongly

recommended to fully charge the battery before its ﬁrst use to improve its performance and life span. Always

use the charger supplied by Compex to recharge the battery.

If the device is not going to be used for over 3 months, ensure that the battery is fully charged. If the device

is not going to be used for over 6 months, ensure that the battery is fully charged and remove it from the

stimulator. Switch the stimulator off before removing the battery.

BATTERY LEVEL

The battery charge level is shown by a battery icon in the bottom left of the screen. The battery icon ﬂashes

when the battery is completely ﬂat. The device can then no longer be used. Recharge it immediately.

RECHARGING

Remove all stimulation cables from the stimulator before recharging it. Connect the charger to a wall socket

and connect the stimulator by sliding the red cover to the right to reveal the charger connector.

14

EN

The charging menu shown below appears automatically.

The charging duration is displayed on the screen. As soon as charging is complete, the battery ﬂashes.

Disconnect the charger: the stimulator will switch off automatically.

15

EN

5. TROUBLESHOOTING

ELECTRODE FAULT

The device emits a tone and alternately displays the pair of electrodes symbol and an arrow pointing towards

the channel on which a problem has been detected. In the above example, the stimulator has detected an

error on channel 1.

Check that the electrodes are connected to this channel.

If electrodes are old, worn and/or if the contact is poor: try using new electrodes.

Try using the stimulation cable on a different channel. If the cable is still faulty, replace it

(www.compexstore.com).

STIMULATION DOES NOT PRODUCE THE USUAL SENSATION

Check that all settings are correct and check electrodes are properly positioned.

Change the position of the electrodes slightly.

STIMULATION CAUSES DISCOMFORT

Electrodes lose their adhesive capacity and no longer provide suitable contact with skin.

Electrodes are worn and must be replaced.

Change the position of the electrodes slightly.

16

EN

THE STIMULATOR IS NOT WORKING

When an error screen is displayed during use, note the error number (in the example, the error number is

1/0/0) and contact the Compex-approved customer service centre.

THE BATTERY IS VERY FLAT

If the following screen appears, switch the device off and connect the charger.

If a battery is very ﬂat, a recovery cycle will start, lasting 2 minutes.

17

EN

When this has ﬁnished, if the battery is working properly, it will start charging; in this case, it is strongly

recommended to perform a charge/discharge cycle for the battery by pressing on the channel 4 button

to launch this cycle, which may take up to 12 hours. If, however, it proves to be faulty, the following screen

appears and the battery must be replaced.

18

EN

6. DEVICE MAINTENANCE

GUARANTEE

See the attached leaﬂet.

MAINTENANCE

Your stimulator does not require neither calibration nor periodic maintenance. However when needed clean

with a soft cloth and solvent-free alcohol-based detergent. Use as little liquid as possible to clean the device.

Do not disassemble the stimulator or the charger as they contain high-voltage components which could

cause electrocution. This must be carried out by Compex-approved technicians or repair services. If your

stimulator contains parts that appear to be worn or faulty, please contact the closest Compex customer

service centre.

CONDITIONS FOR STORAGE/TRANSPORT AND USE

STORAGE AND TRANSPORT USE

TEMPERATURE -20° C to 45° C 0° C to 40° C

MAXIMUM RELATIVE HUMIDITY 75% 30% to 75%

ATMOSPHERIC PRESSURE from 700 hPa to 1060 hPa from 700 hPa to 1060 hPa

Do not use in areas at risk of explosion.

DISPOSAL

Batteries must be disposed of in accordance with national regulatory requirements in force. Any product

bearing the WEEE label (a crossed-out wheeled bin) must be separated from household waste and sent to

special collection facilities for recycling and recovery.

Sidan laddas ...

Sportec FIT 1.0, FIT 3.0, SP 2.0 & SP 4.0 Användarmanual

Sportec FIT 1.0, FIT 3.0, SP 2.0 & SP 4.0 Användarmanual

på andra språk

Andra dokument