Victron energy Quattro 3k 50-50A 230V (firmware xxxx4xx) Bruksanvisning

varumärke: Victron energy

Modell: Quattro 3k 50-50A 230V (firmware xxxx4xx)

Typ: Bruksanvisning

Manual

EN

Handleiding

NL

Manue

l

FR

Anleitung

DE

Manual

ES

Användarhandbok

SE

Appendix

Quattro

(with firmware xxxx400 or higher)

12 | 3000 | 120 – 50|50 – 230V

24 | 3000 | 70 – 50|50 – 230V

48 | 3000 | 35 – 50|50 – 230V

1

EN NL FR DE ES SE Appendix

NOTE:

This manual is intended for products with firmware xxxx400 or higher (with x any number)

The firmware number can be found on the microprocessor, after removing the front panel.

It is possible to update older units, as long as that same 7 digit number starts with either 26 or 27. When it starts with 19 or 20

you have an old microprocessor and it is not possible to update to 400 or higher.

1. SAFETY INSTRUCTIONS

In general

Please read the documentation supplied with this product first, so that you are familiar with the safety signs en directions before

using the product.

This product is designed and tested in accordance with international standards. The equipment should be used for the

designated application only.

WARNING: DANGER OF ELECTRICAL SHOCK

The product is used in combination with a permanent energy source (battery). Even if the equipment is switched off, a

dangerous electrical voltage can occur at the input and/or output terminals. Always switch the AC power off and disconnect the

battery before performing maintenance.

The product contains no internal user-serviceable parts. Do not remove the front panel and do not put the product into

operation unless all panels are fitted. All maintenance should be performed by qualified personnel.

Never use the product at sites where gas or dust explosions could occur. Refer to the specifications provided by the

manufacturer of the battery to ensure that the battery is suitable for use with this product. The battery manufacturer's safety

instructions should always be observed.

WARNING: do not lift heavy objects unassisted.

Installation

Read the installation instructions before commencing installation activities.

This product is a safety class I device (supplied with a ground terminal for safety purposes). Its AC input and/or output

terminals must be provided with uninterruptable grounding for safety purposes. An additional grounding point is

located on the outside of the product. If it can be assumed that the grounding protection is damaged, the product should be

taken out of operation and prevented from accidentally being put into operation again; contact qualified maintenance personnel.

Ensure that the connection cables are provided with fuses and circuit breakers. Never replace a protective device by a

component of a different type. Refer to the manual for the correct part.

Check before switching the device on whether the available voltage source conforms to the configuration settings of the product

as described in the manual.

Ensure that the equipment is used under the correct operating conditions. Never operate it in a wet or dusty environment.

Ensure that there is always sufficient free space around the product for ventilation, and that ventilation openings are not

blocked.

Install the product in a heatproof environment. Ensure therefore that there are no chemicals, plastic parts, curtains or other

textiles, etc. in the immediate vicinity of the equipment.

Transport and storage

On storage or transport of S product, ensure that the mains supply and battery leads are disconnected.

No liability can be accepted for damage in transit if the equipment is not transported in its original packaging.

Store the product in a dry environment; the storage temperature should range from –20°C to 60°C.

Refer to the battery manufacturer's manual for information on transport, storage, charging, recharging and disposal of the

battery.

2

2. DESCRIPTION

2.1 In general

The basis of the Quattro is an extremely powerful sine inverter, battery charger and automatic switch in a compact casing.

The Quattro features the following additional, often unique characteristics:

Two AC inputs; integrated switch-over system between shore voltage and generating set

The Quattro features two AC inputs (AC-in-1 and AC-in-2) for connecting two independent voltage sources. For example, two

generator sets, or a mains supply and a generator set. The Quattro automatically selects the input where voltage is present.

If voltage is present on both inputs, the Quattro selects the AC-in-1 input, to which normally the generating set is connected.

Two AC outputs

Besides the usual uninterruptable output (AC-out-1), an auxiliary output (AC-out-2) is available that disconnects its load in the

event of battery operation. Example: an electric boiler that is allowed to operate only if the genset is running or shore power is

available.

Automatic and uninterruptible switching

In the event of a supply failure or when the genset is switched off, the Quattro will switch over to inverter operation and take

over the supply of the connected devices. This is done so quickly that operation of computers and other electronic devices is

not disturbed (Uninterruptible Power Supply or UPS functionality). This makes the Quattro highly suitable as an emergency

power system in industrial and telecommunication applications. The maximum alternating current that can be switched is 30A.

Three phase capability

Three units can be configured for three-phase output. But that’s not all: up to 6 sets of three units can be parallel connected to

provide 45kW / 54kVA inverter power and more than 1200A charging capacity.

PowerControl – maximum use of limited shore current

The Quattro can supply a huge charging current. This implies heavy loading of the shore connection or generating set. For both

AC inputs, therefore, a maximum current can be set. The Quattro then takes other power users into account, and only uses

'surplus' current for charging purposes.

- Input AC-in-1, to which usually a generating set is connected, can be set to a fixed maximum with DIP switches, with VE.Net

or with a PC, so that the generating set is never overloaded.

- Input AC-in-2 can also be set to a fixed maximum. In mobile applications (ships, vehicles), however, a variable setting by

means of a Multi Control Panel will usually be selected. In this way the maximum current can be adapted to the available shore

current in an extremely simple manner.

PowerAssist – Extended use of your generating set and shore current: the Quattro “co-supply” feature

The Quattro operates in parallel with the generating set or the shore connection. A current shortfall is automatically

compensated: the Quattro draws extra power from the battery and helps along. A current surplus is used to recharge the

battery.

This unique feature offers a definitive solution for the ‘shore current problem’: electric tools, dish washers, washing

machines, electric cooking etc. can all run on 16A shore current, or even less. In addition, a smaller generating set can

be installed.

Three programmable relays

The Quattro is equipped with 3 programmable relays. The relays can be programmed for all kinds of other applications

however, for example as a starter relay for a generating set.

Two programmable analog/digital input/output ports

The Quattro is equipped with 2 analog/digital input/output ports.

These ports can be used for several purposes. One application is communication with the BMS of a lithium-ion battery.

Frequency shift

When solar inverters are connected to the output of a Multi or Quattro, the excess solar energy is used to recharge the

batteries. Once the absorption voltage is reached, the Multi or Quattro will shut down the solar inverter by shifting the output

frequency 1Hz (from 50Hz to 51Hz for example). Once battery voltage has dropped slightly, the frequency returns to normal

and the solar inverters will restart.

Built-in Battery Monitor (optional)

The ideal solution when Multi’s or Quattro’s are part of a hybrid system (diesel generator, inverter/chargers, storage battery,

and alternative energy). The built-in battery monitor can be set to start and stop the generator:

- Start at a preset % discharge level, and/or

- start (with a preset delay) at a preset battery voltage, and/or

- start (with a preset delay) at a preset load level.

- Stop at a preset battery voltage, or

- stop (with a preset delay) after the bulk charge phase has been completed, and/or

- stop (with a preset delay) at a preset load level.

Solar energy

The Quattro is extremely suitable for solar energy applications. It can be used for building autonomous systems as well as

mains-coupled systems.

3

EN NL FR DE ES SE Appendix

Emergency power or autonomous operation on mains failure

Houses or buildings provided with solar panels or a combined micro-scale heating and power plant (a power-generating central

heating boiler) or other sustainable energy sources have a potential autonomous energy supply which can be used for

powering essential equipment (central heating pumps, refrigerators, deep freeze units, Internet connections, etc.) during a

power failure. A problem in this regard, however, is that mains-coupled solar panels and/or micro-scale heating and power

plants drop out as soon as the mains supply fails. With a Quattro and batteries, this problem can be solved in a simple manner:

the Quattro can replace the mains supply during a power failure. When the sustainable energy sources produce more

power than necessary, the Quattro will use the surplus to charge the batteries; in the event of a shortfall, the Quattro will supply

additional power from its battery energy resources.

Programmable with DIP switches, VE.Net panel or personal computer

The Quattro is supplied ready for use. Three features are available for changing certain settings if desired:

- The most important settings (including parallel operation of up to three devices and 3-phase operation) can be changed in a

very simple manner, using Quattro DIP switches.

- All settings, with exception of the multi-functional relay, can be changed with a VE.Net panel.

- All settings can be changed with a PC and free of charge software, downloadable from our website www.victronenergy.com

2.2 Battery charger

Adaptive 4-stage charging characteristics: bulk – absorption – float – storage

The microprocessor-driven adaptive battery management system can be adjusted for various types of batteries. The adaptive

function automatically adapts the charging process to battery use.

The right amount of charge: variable absorption time

In the event of slight battery discharge, absorption is kept short to prevent overcharging and excessive gas formation. After

deep discharging, the absorption time is automatically extended in order to fully charge the battery.

Preventing damage due to excessive gassing: the BatterySafe mode

If, in order to quickly charge a battery, a high charge current in combination with a high absorption voltage has been chosen,

damage due to excessive gassing will be prevented by automatically limiting the rate of voltage increase once the gassing

voltage has been reached.

Less maintenance and aging when the battery is not in use: the Storage mode

The Storage mode kicks in whenever the battery has not been subjected to discharge during 24 hours. In the Storage mode

float voltage is reduced to 2,2V/cell (13,2V for 12V battery) to minimise gassing and corrosion of the positive plates. Once a

week the voltage is raised back to the absorption level to ‘equalize’ the battery. This feature prevents stratification of the

electrolyte and sulphation, a major cause of early battery failure.

Two DC outputs for charging two batteries

The main DC terminal can supply the full output current. The second output, intended for charging a starter battery, is limited to

4A and has a slightly lower output voltage.

Increasing service life of the battery: temperature compensation

The temperature sensor (supplied with the product) serves to reduce charging voltage when battery temperature rises. This is

particularly important for maintenance-free batteries, which could otherwise dry out by overcharging.

Battery voltage sense: the correct charge voltage

Voltage loss due to cable resistance can be compensated by using the voltage sense facility to measure voltage directly on the

DC bus or on the battery terminals.

More on batteries and charging

Our book ‘Energy Unlimited’ offers further information on batteries and battery charging, and is available free of charge on our

website (see www.victronenergy.com -> Support & Downloads’ -> General Technical Information). For more information on

adaptive charging, please also refer to the General Technical Information our website.

2.3 Self consumption – solar energy storage systems

For more information see our white paper Self Consumption or Grid independence with the Victron Energy Storage Hub.

The appropriate software can be downloaded from our website.

When the Multi/Quattro is used in a configuration in which it will feed back energy to the grid it is required to enable grid code

compliance by selecting the grid code country setting with the VEConfigure tool.

This way the Multi/Quattro can comply to the local rules.

Once set, a password will be required to disable grid code compliance or change grid code related parameters.

If the local grid code is not supported by the Multi/Quattro an external certified interface device should be used to connect the

Multi/Quattro to the grid.

The Multi/Quattro can also be used as a bidirectional inverter operating parallel to the grid, integrated into a customer designed

system (PLC or other) that takes care of the control-loop and grid measurement, see

http://www.victronenergy.com/live/system_integration:hub4_grid_parallel

Special note for Australian customers: IEC62109.1 certification and CEC approval for off-grid use does NOT imply approval for

grid-interactive installations. Additional certification to IEC 62109.2 and AS 4777.2.2015 are required before grid-interactive

systems can be implemented. Please check Clean Energy Council website for current approvals.

4

3. OPERATION

3.1 “On / stand by / charger only” switch

When switched to "on", the product is fully functional. The inverter will come into operation and the LED "inverter on" will light

up.

An AC voltage connected to the "AC in" terminal will be switched through to the "AC out" terminal, if within specifications. The

inverter will switch off, the "mains on" LED will light up and the charger commences charging. The "bulk", "absorption" or "float"

LEDs will light up, depending on the charger mode.

If the voltage at the "AC-in" terminal is rejected, the inverter will switch on.

When the switch is switched to "charger only", only the battery charger of the Quattro will operate (if mains voltage is present).

In this mode input voltage also is switched through to the "AC out" terminal.

NOTE: When only the charger function is required, ensure that the switch is switched to "charger only". This prevents the

inverter from being switched on if the mains voltage is lost, thus preventing your batteries from running flat.

3.2 Remote control

Remote control is possible with a 3-way switch or with a Multi Control panel.

The Multi Control panel has a simple rotary knob with which the maximum current of the AC input can be set: see PowerControl

and PowerAssist in Section 2.

3.3 Equalisation and forced absorption

3.3.1 Equalisation

Traction batteries require regular additional charging. In the equalisation mode, the Quattro will charge with increased voltage

for one hour (1V above the absorption voltage for a 12V battery, 2V for a 24V battery). The charging current is then limited to

1/4 of the set value. The “bulk” and “absorption” LED’s flash intermittently.

Equalisation mode supplies a higher charging voltage than most DC consuming

devices can cope with. These devices must be disconnected before additional

charging takes place.

3.3.2 Forced absorption

Under certain circumstances, it can be desirable to charge the battery for a fixed time at absorption voltage level. In Forced

Absorption mode, the Quattro will charge at the normal absorption voltage level during the set maximum absorption time. The

“absorption” LED lights.

3.3.3 Activating equalisation or forced absorption

The Quattro can be put into both these states from the remote panel as well as with the front panel switch, provided that all

switches (front, remote and panel) are set to “on” and no switches are set to “charger only”.

In order to put the Quattro in this state, the procedure below should be followed.

If the switch is not in the required position after following this procedure, it can be switched over quickly once. This will not

change the charging state.

NOTE: Switching from “on” to “charger only” and back, as described below, must be done quickly. The switch must be toggled

such that the intermediate position is 'skipped', as it were. If the switch remains in the “off” position even for a short time, the

device may be turned off. In that case, the procedure must be restarted at step 1. A certain degree of familiarisation is required

when using the front switch on the Compact in particular. When using the remote panel, this is less critical.

Procedure:

Check whether all switches (i.e. front switch, remote switch or remote panel switch if present) are in the “on” position.

Activating equalisation or forced absorption is only meaningful if the normal charging cycle is completed (charger is in 'Float').

To activate:

a. Switch rapidly from “on” to “charger only” and leave the switch in this position for ½ to 2 seconds.

b. Switch rapidly back from “charger only” to “on” and leave the switch in this position for ½ to 2 seconds.

c. Switch once more rapidly from “on” to “charger only” and leave the switch in this position.

On the Quattro (and, if connected, on the MultiControl panel) the three LED’s “Bulk”, “Absorption” and “Float” will now flash 5 times.

Subsequently, the LED’s “Bulk”, “Absorption” and “Float” will each light during 2 seconds.

a. If the switch is set to “on” while the “Bulk” LED lights, the charger will switch to equalisation.

b. If the switch is set to “on” while the “Absorption” LED lights, the charger will switch to forced absorption.

c. If the switch is set to “on” after the three LED sequence has finished, the charger will switch to “Float”.

d. If the switch is has not been moved, the Quattros will remain in ‘charger only’ mode and switch to “Float”.

5

EN NL FR DE ES SE Appendix

3.4 LED indications and their meaning

LED off

LED flashes

LED lights

Inverter

charger

inverter

The inverter is on, and supplies

power to the load.

mains on

on

inverter on

bulk

overload

off

absorption

low battery

charger

only

float

temperature

charger

inverter

The nominal power of the inverter is

exceeded. The “overload” LED

flashes.

mains on

on

inverter on

bulk

overload

off

absorption

low battery

charger

only

float

temperature

charger

inverter

The inverter is switched off due to

overload or short circuit.

mains on

on

inverter on

bulk

overload

off

absorption

low battery

charger

only

float

temperature

charger

inverter

The battery is almost empty.

mains on

on

inverter on

bulk

overload

off

absorption

low battery

charger

only

float

temperature

charger

inverter

The inverter is

switched off due to

low battery voltage.

mains on

on

inverter on

bulk

overload

off

absorption

low battery

charger

only

float

temperature

charger

inverter

The internal

temperature is

reaching a critical

level.

mains on

on

inverter on

bulk

overload

off

absorption

low battery

charger

only

float

temperature

6

charger

inverter

The inverter is switched off due to

excessively high internal

temperature.

mains on

on

inverter on

bulk

overload

off

absorption

low battery

charger

only

float

temperature

charger

inverter

– If the LEDs flash alternately, the

battery almost empty and nominal

power is exceeded.

– If “overload” and “low battery”

flash simultaneously, there is an

excessively high ripple voltage at

the battery connection.

mains on

on

inverter on

bulk

overload

off

absorption

low battery

charger

only

float

temperature

charger

inverter

The inverter is switched off due to

an excessively high ripple voltage

on the battery connection.

mains on

on

inverter on

bulk

overload

off

absorption

low battery

charger

only

float

temperature

7

EN NL FR DE ES SE Appendix

Battery charger

charger

inverter

The AC voltage on AC-in-1 or

AC-in-2 is switched through, and

the charger operates in bulk phase.

mains on

on

inverter on

bulk

overload

off

absorption

low battery

charger

only

float

temperature

charger

inverter

The AC voltage on AC-in-1 or

AC-in-2 is switched through and the

charger operates, but the set

absorption voltage has not yet been

reached (battery protection mode)

mains on

on

inverter on

bulk

overload

off

absorption

low battery

charger

only

float

temperature

charger

inverter

The AC voltage on AC-in-1 or

AC-in-2 is switched through, and

the charger operates in absorption

phase.

mains on

on

inverter on

bulk

overload

off

absorption

low battery

charger

only

float

temperature

charger

inverter

The AC voltage on AC-in-1 or

AC-in-2 is switched through, and

the charger operates in float or

storage phase.

mains on

on

inverter on

bulk

overload

off

absorption

low battery

charger

only

float

temperature

charger

inverter

The AC voltage on AC-in-1 or

AC-in-2 is switched through, and

the charger operates in equalisation

mode.

mains on

on

inverter on

bulk

overload

off

absorption

low battery

charger

only

float

temperature

8

Special indications

Set with limited input current

charger

inverter

The AC voltage on AC1-in-1 or

AC-in-2 is switched through. The

AC-input current is equal to the

load current. The charger is down-

controlled to 0A.

mains on

on

inverter on

bulk

overload

off

absorption

low battery

charger

only

float

temperature

Set to supply additional current

charger

inverter

The AC voltage on AC-in-1 or

AC-in-2 is switched through, but the

load demands more current than

the mains can supply. The inverter

is now switched on to supply

additional current.

mains on

on

inverter on

bulk

overload

off

absorption

low battery

charger

only

float

temperature

9

EN NL FR DE ES SE Appendix

4. INSTALLATION

This product may only be installed by a qualified electrical engineer.

4.1 Location

The Quattro should be installed in a dry, well-ventilated location, as close as possible to the batteries. The device should be

surrounded by a free space of at least 10 cm for cooling purposes.

An excessively high environmental temperature has the following

consequences:

- shorter lifespan

- lower charging current

- lower peak power or inverter shut-down.

Never place the device directly above the batteries.

The Quattro is suitable for wall mounting. For mounting purposes, a hook and two holes are provided at the back of the casing

(see appendix G). The device can be fitted either horizontally or vertically. For optimal cooling, vertical fitting is preferred.

The inner part of the device should remain accessible after installation.

The distance between the Quattro and the battery should be as short as possible to reduce voltage loss across the battery

cables to a minimum.

Install the product in a heatproof environment.

Ensure therefore that there are no chemicals, plastic parts,

curtains or other textiles, etc. in the direct vicinity.

The Quattro has no internal DC fuse. The DC fuse should be

installed outside the Quattro.

4.2 Connecting the battery cables

In order to use the full potential of the Quattro, batteries of sufficient capacity and battery cables with the correct cross-section

should be used.

See table:

12/3000/120

24/3000/70

48/3000/35

Recommended battery capacity

(Ah)

400–1200 200–700 100–400

Recommended DC fuse

400A

300A

125A

Recommended cross-section

(mm2) per + and - connection

terminal

0 – 5 m*

2x 50 mm2

50 mm2

35 mm2

5 -10 m*

2x 70 mm2

2x 50 mm2

2x 35 mm2

* ‘2x’ means two positive and two negative cables.

Procedure

To connect the battery cables, follow the procedure below:

Use a torque wrench with insulated box spanner in order to avoid shorting the

battery.

Maximum torque: 9 Nm

Avoid shorting the battery cables To prevent short circuiting of the battery, an

isolated box wrench should be used.

- Loosen the four lower front panel screws at the front of the unit, and remove the lower front panel.

- Connect the battery cables: + (red) to the right-hand terminal and - (black) to the left-hand terminal (see appendix A).

- Tighten the connections after mounting the fastening parts.

10

4.3 Connecting AC cables

The Quattro is a safety class I product (supplied with an ground terminal for safety

purposes). Its AC input and/or output terminals and/or grounding point on

the outside of the product must be provided with an uninterruptable

grounding point for safety purposes. See the following instructions in this

regard.

The Quattro is provided with a ground relay (see appendix) that automatically

connects the N output to the casing if no external AC supply is available. If

an external AC supply is provided, the ground relay will open before the input

safety relay closes (relay H in appendix B). This ensures the correct operation of

an earth leakage circuit breaker that is connected to the output.

In a fixed installation, an uninterruptable grounding can be secured by means of

the grounding wire of the AC input. Otherwise the casing must be grounded.

In a mobile installation (for example, with a shore current plug), interrupting the

shore connection will simultaneously disconnect the grounding connection. In that

case, the casing must be connected to the chassis (of the vehicle) or to the hull or

grounding plate (of the boat).

In general, the connection described above to shore connection grounding is not

recommended for boats because of galvanic corrosion. The solution to this is

using an isolating transformer.

The inverter does incorporate a mains frequency isolating transformer. This precludes the possibility of DC current at any AC

port. Therefore type A RCD’s can be used.

AC-in-1 (see appendix A)

If AC voltage is present on these terminals, the Quattro will use this connection. Generally a generator will be connected to AC-

in-1.

The AC-in-1 input must be protected by a fuse or magnetic circuit breaker rated at 50A or less, and cable cross-

section must be sized accordingly. If the input AC supply is rated at a lower value, the fuse or magnetic circuit breaker

should be down sized accordingly.

AC-in-2 (see appendix A)

If AC voltage is present on these terminals, the Quattro will use this connection, unless voltage is also present on

AC-in-1. The Quattro will then automatically select AC-in-1. Generally the mains supply or shore voltage will be connected

to AC-in-2.

The AC-in-2 input must be protected by a fuse or magnetic circuit breaker rated at 50A or less, and cable cross-

section must be sized accordingly. If the input AC supply is rated at a lower value, the fuse or magnetic circuit breaker

should be down sized accordingly.

Note: The Quattro may not start when AC is present only on AC-in-2, and DC battery voltage is 10% or more below

nominal (less than 11 Volt in case of a 12 Volt battery).

Solution: connect AC power to AC-in-1, or recharge the battery.

AC-out-1 (see appendix A)

The AC output cable can be connected directly to the terminal block "AC-out".

With its PowerAssist feature the Quattro can add up to 3kVA (that is 3000 / 230 = 13A) to the output during periods of peak

power requirement. Together with a maximum input current of 50A this means that the output can supply up to 50 + 13 = 63A.

An earth leakage circuit breaker and a fuse or circuit breaker rated to support the expected load must be included in

series with the output, and cable cross-section must be sized accordingly. The maximum rating of the fuse or circuit

breaker is 63A.

AC-out-2 (see appendix A)

A second output is available that disconnects its load in the event of battery operation. On these terminals, equipment is

connected that may only operate if AC voltage is available on AC-in-1 or AC-in-2, e.g. an electric boiler or an air

conditioner. The load on AC-out-2 is disconnected immediately when the Quattro switches to battery operation. After AC power

becomes available on AC-in-1 or AC-in-2, the load on AC-out-2 will be reconnected with a delay of approximately 2 minutes.

This to allow a genset to stabilise.

AC-out-2 can support loads of up to 25A. An earth leakage circuit breaker and fuse rated at max. 25A must be connected in

series with AC-out-2.

Procedure

Use three-core cable. The connection terminals are clearly encoded:

PE: earth

N: neutral conductor

L: phase/live conductor

11

EN NL FR DE ES SE Appendix

4.4 Connection options

4.4.1 Starter battery (connection terminal E, see appendix A)

The Quattro has a connection for charging a starter battery. Output current is limited to 4A.

4.4.2 Voltage sense (connection terminal E, see appendix A)

For compensating possible cable losses during charging, two sense wires can be connected with which the voltage directly on

the battery or on the positive and negative distribution points can be measured. Use wire with a cross-section of 0,75mm².

During battery charging, the Quattro will compensate the voltage drop over the DC cables up to a maximum of 1 Volt (i.e. 1V

over the positive connection and 1V over the negative connection). If the voltage drop threatens to become larger than 1V, the

charging current is limited in such a way that the voltage drop remains limited to 1V.

4.4.3 Temperature sensor (connection terminal E, see appendix A)

For temperature-compensated charging, the temperature sensor (supplied with the Quattro) can be connected. The sensor is

isolated and must be fitted to the negative terminal of the battery.

4.4.4 Remote control

The Quattro can be remotely controlled in two ways:

With an external switch (connection terminal H, see appendix A). Operates only if the switch on the Quattro is set to “on”.

With a Multi control panel (connected to one of the two RJ48 sockets B, see appendix A). Operates only if the switch on the

Quattro is set to “on”.

Using the Multi control panel, only the current limit for AC-in-2 can be set (in regard to PowerControl and PowerAssist).

The current limit for AC-in-1 can be set with DIP switches or by means of software.

Only one remote control can be connected, i.e. either a switch or a Multi control panel.

4.4.5. Programmable relay

The Quattro is equipped with a multi-functional relay that by default is programmed as an alarm relay. The relay can be

programmed for all kinds of other applications however, for example to start a generator (VEConfigure software needed).

4.4.6 Auxiliary AC output (AC-out-2)

Besides the usual uninterruptable output (AC-out-1), a second output (AC-out-2) is available that disconnects its load in the

event of battery operation. Example: an electric boiler or air conditioner that is allowed to operate only if the genset is running or

shore power is available.

In case of battery operation, AC-out-2 is switched off immediately. After the AC supply has become available, AC-out-2 is

reconnected with a delay of 2 minutes, this allow a genset to stabilize prior to connecting a heavy load.

4.4.7 Connecting Quattros in parallel (see appendix C)

The Quattro can be connected in parallel with several identical devices. To this end, a connection is established between the

devices by means of standard RJ45 UTP cables. The system (one or more Quattros plus optional control panel) will require

subsequent configuration (see Section 5).

In the event of connecting Quattro units in parallel, the following requirements must be met:

- A maximum of six units connected in parallel.

- Only identical devices with the same power ratings may be connected in parallel.

- Battery capacity should be sufficient.

- The DC connection cables to the devices must be of equal length and cross-section.

- If a positive and a negative DC distribution point is used, the cross-section of the connection between the batteries and the

DC distribution point must at least equal the sum of the required cross-sections of the connections between the distribution

point and the Quattro units.

- Place the Quattro units close to each other, but allow at least 10 cm for ventilation purposes under, above and beside the

units.

- UTP cables must be connected directly from one unit to the other (and to the remote panel). Connection/splitter boxes are not

permitted.

- A battery-temperature sensor need only be connected to one unit in the system. If the temperature of several batteries is to be

measured, you can also connect the sensors of other Quattro units in the system (with a maximum of one sensor per Quattro).

Temperature compensation during battery charging responds to the sensor indicating the highest temperature.

- Voltage sensing must be connected to the master (see Section 5.5.1.4).

- Only one remote control means (panel or switch) can be connected to the system.

4.4.8 Three-phase configuration (see appendix C)

Quattros can also be used in 3-phase configuration wye (Y). To this end, a connection between the devices is made by means

of standard RJ45 UTP cables (the same as for parallel operation). The system (Quattros plus an optional control panel) will

require subsequent configuration (see Section 5).

Pre-requisites: see Section 4.4.7.

Note: the Quattro is not suitable for 3-phase delta (Δ) configuration.

12

5. CONFIGURATION

- Settings may only be changed by a qualified electrical engineer.

- Read the instructions thoroughly before implementing changes.

- During setting of the charger, the DC fuse in the battery connections must be

removed.

5.1 Standard settings: ready for use

On delivery, the Quattro is set to standard factory values. In general, these settings are selected for single-unit operation.

Settings, therefore, do not require changing in the event of stand-alone use.

Warning: Possibly, the standard battery charging voltage is not suitable for your batteries! Refer to the manufacturer's

documentation, or to your battery supplier!

Standard Quattro factory settings

Inverter frequency 50 Hz

Input frequency range 45 - 65 Hz

Input voltage range 180 - 265 VAC

Inverter voltage 230 VAC

Stand-alone / parallel / 3-phase stand-alone

AES (Automatic Economy Switch) off

Ground relay on

Charger on/ off on

Charging characteristics four-stage adaptive with BatterySafe mode

Charging current 75% of the maximum charging current

Battery type Victron Gel Deep Discharge (also suitable for Victron AGM Deep

Discharge)

Automatic equalisation charging off

Absorption voltage 14.4 / 28.8 / 57.6 V

Absorption time up to 8 hours (depending on bulk time)

Float voltage 13.8 / 27.6 / 55.2 V

Storage voltage 13.2V (not adjustable)

Repeated absorption time 1 hour

Absorption repeat interval 7 days

Bulk protection on

Generator (AC-in-1) / shore current (AC-in-2) 50A/16A (= adjustable current limit for PowerControl and

PowerAssist functions)

UPS feature on

Dynamic current limiter off

WeakAC off

BoostFactor 2

Programmable relay alarm function

PowerAssist on

5.2 Explanation of settings

Settings that are not self-explanatory are described briefly below. For further information, please refer to the help files in the

software configuration programs (see Section 5.3).

Inverter frequency

Output frequency if no AC is present at the input.

Adjustability: 50Hz; 60Hz

Input frequency range

Input frequency range accepted by the Quattro. The Quattro synchronises within this range with the voltage present on AC-in-1

(priority input) or AC-in-2. Once synchronised, the output frequency will be equal to the input frequency.

Adjustability: 45 – 65 Hz; 45 – 55 Hz; 55 – 65 Hz

Input voltage range

Voltage range accepted by the Quattro. The Quattro synchronises within this range with the voltage present on AC-in-1 (priority

input) or on AC-in-2. After the back feed relay has closed, output voltage will be equal to input voltage.

Adjustability:

Lower limit: 180 - 230V

Upper limit: 230 - 270V

Note: the standard lower limit setting of 180V is intended for connection to a weak mains supply, or to a generator with

unstable AC output. This setting may result in a system shut down when connected to a ‘brushless, self excited, externally

voltage regulated, synchronous AC generator’ (synchronous AVR generator). Most generators rated at 10kVA or more are

synchronous AVR generators. The shut down is initiated when the generator is stopped and revs down while the AVR

simultaneously ‘tries’ to keep the output voltage of the generator at 230V.

The solution is to increase the lower limit setting to 210VAC (the output of AVR generators is generally very stable), or to

disconnect the Multi(s) from the generator when a generator stop signal is given (with help of an AC contacor installed in series

with the generator).

13

EN NL FR DE ES SE Appendix

Inverter voltage

Output voltage of the Quattro in battery operation.

Adjustability: 210 – 245V

Stand-alone / parallel operation / 2-3 phase setting

Using several devices, it is possible to:

- increase total inverter power (several devices in parallel)

- create a split-phase system (only for Quattro units with 120V output voltage)

- create a 3-phase system.

To this end, the devices must be mutually connected with RJ45 UTP cables. Standard device settings, however, are such that

each device operates in stand-alone operation. Reconfiguration of the devices is therefore required.

AES (Automatic Economy Switch)

If this setting is turned ‘on’, the power consumption in no-load operation and with low loads is decreased by approx. 20%, by

slightly 'narrowing' the sinusoidal voltage. Not adjustable with DIP switches. Applicable in stand-alone configuration only.

Search Mode

Instead of the AES mode, the search mode can also be chosen (with help of VEConfigure only).

If search mode is ‘on’, the power consumption in no-load operation is decreased by approx. 70%. In this mode the Quattro,

when operating in inverter mode, is switched off in case of no load or very low load, and switches on every two seconds for a

short period. If the output current exceeds a set level, the inverter will continue to operate. If not, the inverter will shut down

again.

The Search Mode “shut down” and “remain on” load levels can be set with VEConfigure.

The standard settings are:

Shut down: 40 Watt (linear load)

Turn on: 100 Watt (linear load)

Not adjustable with DIP switches. Applicable in stand-alone configuration only.

Ground relay (see appendix B)

With this relay (H), the neutral conductor of the AC output is grounded to the casing when the back feed safety relays in the

AC-in-1 and the AC-in-2 inputs are open. This ensures the correct operation of earth leakage circuit breakers in the outputs.

If a non-grounded output is required during inverter operation, this function must be turned off. (See also Section 4.5)

Not adjustable with DIP switches.

If required an external ground relay can be connected (for a split-phase system with a separate autotransformer).

See appendix A.

Battery charge curve

The standard setting is ‘Four-stage adaptive with BatterySafe mode’. See Section 2 for a description.

This is the best charging characteristic. See the help files in the software configuration programs for other features.

‘Fixed’ mode can be selected with DIP switches.

Battery type

The standard setting is the most suitable for Victron Gel Deep Discharge, Gel Exide A200, and tubular plate stationary batteries

(OPzS). This setting can also be used for many other batteries: e.g. Victron AGM Deep Discharge and other AGM batteries,

and many types of flat-plate open batteries. Four charging voltages can be set with DIP switches.

With VEConfigure the charge curve can be adjusted to charge any battery type (Nickel Cadmium batteries, Lithium-ion

batteries)

Automatic equalisation charging

This setting is intended for tubular plate traction batteries. During absorption the voltage limit increases to 2,83V/cell (34V for a

24V battery) once the charge current has tapered down to less than 10% of the set maximum current.

Not adjustable with DIP switches.

See ’tubular plate traction battery charge curve’ in VEConfigure.

Absorption time

This depends on the bulk time (adaptive charging characteristic), so that the battery is optimally charged. If the ‘fixed’ charging

characteristic is selected, the absorption time is fixed. For most batteries, a maximum absorption time of eight hours is suitable.

If an extra high absorption voltage is selected for rapid charging (only possible for open, flooded batteries!), four hours is

preferable. With DIP switches, a time of eight or four hours can be set. For the adaptive charging characteristic, this determines

the maximum absorption time.

Storage voltage, Repeated Absorption Time, Absorption Repeat Interval

See Section 2. Not adjustable with DIP switches.

Bulk Protection

When this setting is ‘on’, the bulk charging time is limited to 10 hours. A longer charging time could indicate a system error (e.g.

a battery cell short-circuit). Not adjustable with DIP switches.

14

AC input current limit AC-in-1 (generator) / AC-in-2 (shore/grid supply)

These are the current limit settings at which PowerControl and PowerAssist come into operation.

PowerAssit setting range:

- From 5,3A to 50A for input AC-in-1

- From 5,3A to 50A for input AC-in-2

Factory setting: the maximum value (50A and 16A).

In case of parallel units the range the minimum and maximum values have to be multiplied by the number of parallel units.

See Section 2, the book 'Energy Unlimited', or the many descriptions of this unique feature on our website

www.victronenergy.com .

UPS feature

If this setting is ‘on’ and AC on the input fails, the Quattro switches to inverter operation practically without interruption. The

Quattro can then be used as an Uninterruptible Power Supply (UPS) for sensitive equipment such as computers or

communication systems.

The output voltage of some small generating sets is too unstable and distorted for using this setting – the Quattro would

continually switch to inverter operation. For this reason, the setting can be turned off. The Quattro will then respond less quickly

to voltage deviations on AC-in-1 or AC-in-2. The switchover time to inverter operation is consequently slightly longer, but most

equipment (computers, clocks or household equipment) is not adversely impacted.

Recommendation: Turn the UPS feature off if the Quattro fails to synchronise, or continually switches back to inverter

operation.

Dynamic current limiter

Intended for generators, the AC voltage being generated by means of a static inverter (so-called ‘inverter’ generators). In these

generators, rotational speed is down-controlled if the load is low: this reduces noise, fuel consumption and pollution. A

disadvantage is that the output voltage will drop severely or even completely fail in the event of a sudden load increase. More

load can only be supplied after the engine is up to speed.

If this setting is ‘on’, the Quattro will start supplying extra power at a low generator output level and gradually allow the

generator to supply more, until the set current limit is reached. This allows the generator engine to get up to speed.

This setting is also often used for ‘classical’ generators that respond slowly to sudden load variation.

WeakAC

Strong distortion of the input voltage can result in the charger hardly operating or not operating at all. If WeakAC is set, the

charger will also accept a strongly distorted voltage, at the cost of greater distortion of the input current.

Recommendation: Turn WeakAC on if the charger is hardly charging or not charging at all (which is quite rare!). Also turn on

the dynamic current limiter simultaneously, and reduce the maximum charging current to prevent overloading the generator if

necessary.

Note: when WeakAC is on, the maximum charge current is reduced by approximately 20%.

Not adjustable with DIP switches.

BoostFactor

Change this setting only after consulting with Victron Energy or with an engineer trained by Victron Energy!

Not adjustable with DIP switches.

Three programmable relays

The Quattro is equipped with 3 programmable relays. The relays can be programmed for all kinds of other applications, for

example as a starter relay for a generating set. The default setting of the relay in postion I (see appendix A, upper right corner)

is ‘alarm’.

Not adjustable with DIP switches.

Frequency shift

When solar inverters are connected to the output of a Multi or Quattro, the excess solar energy is used to recharge the

batteries. Once the absorption voltage is reached, the Multi or Quattro will shut down the solar inverter by shifting the output

frequency 1Hz (from 50Hz to 51Hz for example). Once battery voltage has dropped slightly, the frequency returns to normal

and the solar inverters will restart.

Not adjustable with DIP switches.

Built-in Battery Monitor (optional)

The ideal solution when Multi’s or Quattro’s are part of a hybrid system (diesel generator, inverter/chargers, storage battery,

and alternative energy). The built-in battery monitor can be set to start and stop the generator:

- Start at a preset % discharge level, and/or

- start (with a preset delay) at a preset battery voltage, and/or

- start (with a preset delay) at a preset load level.

- Stop at a preset battery voltage, or

- stop (with a preset delay) after the bulk charge phase has been completed, and/or

- stop (with a preset delay) at a preset load level.

Not adjustable with DIP switches.

Auxiliary AC output (AC-out-2)

Besides the uninterruptable output (AC-out-1), a second output (AC-out-2) is available that disconnects its load in the event of

battery operation. Example: an electric boiler or air conditioner that is allowed to operate only if the genset is running or shore

power is available.

In case of battery operation, AC-out-2 is switched off immediately. After the AC supply has become available, AC-out-2 is

reconnected with a delay of 2 minutes, this to allow a genset to stabilise prior to connecting a heavy load.

15

EN NL FR DE ES SE Appendix

5.3 Configuration by computer

All settings can be changed by means of a computer or with a VE.Net panel (except for the multi-functional relay and the

VirtualSwitch when using VE.Net).

The most common settings can be changed by means of DIP switches (see Section 5.5).

NOTE:

This manual is intended for products with firmware xxxx400 or higher (with x any number)

The firmware number can be found on the microprocessor, after removing the front panel.

It is possible to update older units, as long as that same 7 digit number starts with either 26 or 27. When it starts with 19 or 20

you have an old microprocessor and it is not possible to update to 400 or higher.

For changing settings with the computer, the following is required:

- VEConfigure3 software: can be downloaded free of charge at www.victronenergy.com.

- A MK3-USB (VE.Bus to USB) interface, and a RJ45 UTP cable.

Alternatively, the Interface MK2.2b (VE.Bus to RS232) and a RJ45 UTP cable can be used.

5.3.1 VE.Bus Quick Configure Setup

VE.Bus Quick Configure Setup is a software program with which systems with a maximum of three Quattro units (parallel or

three phase operation) can be configured in a simple manner. VEConfigure3 forms part of this program.

The software can be downloaded free of charge at www.victronenergy.com .

5.3.2 VE.Bus System Configurator

For configuring advanced applications and/or systems with four or more Quattro units, VE.Bus System Configurator software

must be used. The software can be downloaded free of charge at www.victronenergy.com . VEConfigure3 forms part of this

program.

5.4 Configuration with a VE.Net panel

To this end, a VE.Net panel and the VE.Net to VE.Bus converter is required.

With VE.Net all parameters are accessible, with the exception of the multi-functional relay and the VirtualSwitch.

16

5.5 Configuration with DIP switches

Introduction

A number of settings can be changed using DIP switches (see appendix A, position M).

Note: When changing settings with dipswitches in a parallel or split-phase/3-phase system one should be aware that not all

settings are relevant on all Quattros. This because some settings will be dictated by the Master or Leader.

Some settings are only relevant in the Master/Leader (ie they are not relevant in a slave or in a follower). Other settings are not

relevant for slaves but are relevant for followers.

A note on used terminology:

A system in which more than one Quattro is used to create a single AC phase is called a parallel system. In this case one of the

Quattros will control the whole phase, this one is called the master. The others, called slaves, will just listen to the master to

determine their action.

It is also possible to create more AC phases (split-phase or 3-phase) with 2 or 3 Quattros. In this case the Quattro in Phase L1

is called the Leader. The Quattro in phase L2 (and L3 if available) will generate the same AC frequency but will follow L1 with a

fixed phase shift. These Quattros are called followers.

If more Quattros are used per phase in a split-phase or 3-phase system (for instance 6 Quattros used to build a 3-phase

system with 2 Quattros per phase) then the Leader of the system is also the Master of phase L1. The Followers in phase L2

and L3 will also take the Master role in phase L2 and L3. All others will be slaves.

Setting up parallel or split-phase/3-phase systems should be done by software, see paragraph 5.3.

TIP: If you don’t want to bother about a Quattro being a master/slave/follower then the easiest and most straight forward

way is to set all settings identically on all Quattros.

General procedure:

Turn the Quattro on, preferably unloaded en without AC voltage on the inputs. The Quattro will then operate in inverter mode.

Step 1: Set the DIP switches for:

- the required current limitation of the AC input. (not relevant for slaves)

- limitation of the charging current. (only relevant for Master/Leader)

Press the 'Up' button for 2 seconds (upper button to the right of the DIP switches, see appendix A, position K) to store the

settings after the required values have been set. You can now re-use the DIP switches to apply the remaining settings (step 2).

Step 2: other settings, set the dipswitches for:

- Charge voltages (only relevant for Master/Leader)

- Absorption time (only relevant for Master/Leader)

- Adaptive charging (only relevant for Master/Leader)

- Dynamic current limiter (not relevant for slaves)

- UPS function (not relevant for slaves)

- converter voltage (not relevant for slaves)

- converter frequency (only relevant for Master/Leader)

Press the 'Down' button for 2 seconds (lower button to the right of the DIP switches) to store the settings after the dipswitches

have been set in the correct position. You can now leave the DIP switches in the selected positions, so that the ’other settings’

can always be recovered.

Remark:

- The DIP switch functions are described in 'top to bottom' order. Since the uppermost DIP switch has the highest number (8),

descriptions start with the switch numbered 8.

5.5.1 Step 1

5.5.1.1 Current limitation AC inputs (default: AC-in-1: 50A, AC-in-2: 16A)

When the AC input current drawn by the Quattro (due to the connected loads and the battery charger) rises and is about to

exceed the AC input current limit, the Quattro will first reduce its charging current (PowerControl) and subsequently, if needed,

supply additional power from the battery (PowerAssist). This way the Quattro will try to prevent that the input current exceeds

the set limit.

The AC-in-1 current limit (the generator) can be set to eight different values by means of DIP switches.

The AC-in-2 current limit can be set to two different values by means of DIP switches.

With a Multi Control Panel, a variable current limit can be set for the AC-in-2 input.

17

EN NL FR DE ES SE Appendix

Procedure

AC-in-1 can be set using DIP switches ds8, ds7 and ds6 (default setting: 50A).

Procedure: set the DIP switches to the required value:

ds8 ds7 ds6

off off off = 6A (1,4kVA at 230V)

off off on = 10A (2.3kVA at 230V)

off on off = 12A (2.8kVA at 230V)

off on on = 16A (3.7kVA at 230V)

on off off = 20A (4.6kVA at 230V)

on off on = 25A (5,7kVA at 230V)

on on off = 30A (6,9kVA at 230V)

on on on = 50A (11,5kVA at 230V)

Remark: Manufacturer-specified continuous power ratings for small generators are sometimes inclined to be rather

optimistic. In that case, the current limit should be set to a much lower value than would otherwise be

required on the basis of manufacturer-specified data.

AC-in-2 can be set in two steps using DIP switch ds5 (default setting: 16A).

Procedure: set ds5 to the required value:

ds5

off = 16A

on = 30A

More than 30A: with VEConfigure software or a Digital Multi Control Panel

Important: When a panel is connected, the AC-in-2 current limit is determined by the panel and not by the value stored in the

Quattro.

5.5.1.2 Charge current limitation (default setting 75%)

For maximum lead acid battery life, a charge current of 10% to 20% of the capacity in Ah should be applied.

Example: optimal charge current of a 24V/500Ah battery bank: 50A to 100A.

The temperature sensor supplied automatically adjusts the charging voltage to the battery temperature.

If faster charging – and a subsequent higher current – is required:

- the temperature sensor supplied should be fitted to the battery, since fast charging can lead to a considerable temperature

rise of the battery bank. The charging voltage is adapted to the higher temperature (i.e. lowered) by means of the temperature

sensor.

- the bulk charging time will sometimes be so short that a fixed absorption time would be more satisfactory (‘fixed’ absorption

time, see ds5, step 2).

Procedure

The battery charging current can be set in four steps, using DIP switches ds4 and ds3 (default setting: 75%).

ds4 ds3

off off = 25%

off on = 50%

on off = 75%

on on = 100%

Note: when WeakAC is on, the maximum charge current is reduced from 100% to approximately 80%.

5.5.1.3 DIP switches ds2 and ds1 are not used during step 1.

IMPORTANT NOTE:

If the last 3 digits of the Multi firmware is in the 100 range (so the firmware number is xxxx1xx (with x any numer))

then ds1 & ds2 are used to set a Multi in stand-alone, parallel or three-phase. Please consult the appropriate manual.

18

5.5.1.4 Examples

examples of settings:

To store the settings after the required values have been set: press the 'Up' button for 2 seconds (upper button to the right of

the DIP switches, see appendix A, position K). The overload and low-battery LED’s will flash to indicate acceptance of the

settings.

We recommend making a note of the settings, and filing this information in a safe place.

The DIP switches can now be used to apply the remaining settings (step 2).

5.5.2 Step 2: Other settings

The remaining settings are not relevant for slaves.

Some of the remaining settings are not relevant for followers (L2, L3). These settings are imposed on the whole system by the

leader L1. If a setting is irrelevant for L2, L3 devices, this is mentioned explicitly.

ds8-ds7: Setting charging voltages (not relevant for L2, L3)

ds8-ds7

Absorption

voltage

Float

oltage

Storage

voltage

Suitable for

off off

14.1

28.2

56.4

13.8

27.6

55.2

13.2

26.4

52.8

Gel Victron Long Life (OPzV)

Gel Exide A600 (OPzV)

Gel MK battery

off on

14.4

28.8

57.6

13.8

27.6

55.2

13.2

26.4

52.8

Gel Victron Deep Discharge

Gel Exide A200

AGM Victron Deep Discharge

Stationary tubular plate (OPzS)

on off

14.7

29.4

58.8

13.8

27.6

55.2

13.2

26.4

52.8

AGM Victron Deep Discharge

Tubular plate (OPzS) batteries in

semi-float mode

AGM spiral cell

on on

15.0

30.0

60.0

13.8

27.6

55.2

13.2

26.4

52.8

Tubular plate (OPzS) batteries in

cyclic mode

ds6: absorption time 8 or 4 hours (not relevant for L2, L3) on = 8 hours off = 4 hours

ds5: adaptive charging characteristic (not relevant for L2, L3) on = active off = inactive (fixed absorption time)

ds4: dynamic current limiter on = active off = inactive

ds3: UPS function on = active off = inactive

ds2: converter voltage on = 230V off = 240V

ds1: converter frequency (not relevant for L2, L3) on = 50Hz off = 60Hz

(the wide input frequency range (45-55Hz) is 'on' by default)

Note:

- If “adaptive charging algorithm” is on, ds6 sets the maximum absorption time to 8 hours or 4 hours.

- If “adaptive charging algorithm” is off, the absorption time is set to 8 hours or 4 hours (fixed) by ds6.

DS-8 AC-in-1

on

DS-7 AC-in-1

on

DS-6 AC-in-1

on

DS-5 AC-in-2

on

DS-4 Charging current

on

DS-3 Charging current

off

DS-2 Stand-alone mode

off

DS-1 Stand-alone mode

off

DS-8

on

DS-7

on

DS-6

on

DS-5

off

DS-4

on

DS-3

on

DS-2

off

DS-1

off

DS-8

off

DS-7

on

DS-6

on

DS-5

off

DS-4

on

DS-3

on

DS-2

off

DS-1

off

DS-8

on

DS-7

on

DS-6

off

DS-5

on

DS-4

off

DS-3

on

DS-2

off

DS-1

off

Step1, stand-alone

Example 1 (factory setting):

8, 7, 6 AC-in-1: 50A

5 AC-in-2: 30A

4, 3 Charge current: 75%

2, 1 Stand-alone mode

Step1, stand-alone

Example 2:

8, 7, 6 AC-in-1: 50A

5 AC-in-2: 16A

4, 3 Charge: 100%

2, 1 Stand-alone

Step1, stand-alone

Example 3:

8, 7, 6 AC-in-1: 16A

5 AC-in-2: 16A

4, 3 Charge: 100%

2, 1 Stand-alone

Step1, stand-alone

Example 4:

8, 7, 6 AC-in-1: 30A

5 AC-in-2: 30A

4, 3 Charge: 50%

2, 1 Stand-alone

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Sidan laddas ...

Victron energy Quattro 3k 50-50A 230V (firmware xxxx4xx) Bruksanvisning

varumärke: Victron energy

Modell: Quattro 3k 50-50A 230V (firmware xxxx4xx)

Typ: Bruksanvisning

Ladda ner pdf

på andra språk

Relaterade papper

Andra dokument