Silvercrest SON 90 A1 Operating Instructions Manual

KOMPERNASS GMBH

BURGSTRASSE 21 · D-44867 BOCHUM

www.kompernass.com

ID-Nr.: SON 90 A1-01/10-V4

Overlock Sewing Machine SON 90 A1

3

Overlock Sewing Machine

Operating instructions

Overlock-symaskin

Bruksanvisning

Saumuri

Käyttöohje

Overlock-Nähmaschine

Bedienungsanleitung

CY

Ραπτομηχανή-Overlock

Οδηγίες χρήσης

CY

Opletilni (overlock)

šivalni stroj

Navodila za uporabo

SON 90 A1

1

3

4

5

6

7

8

9

0

q

uztr

e

w

p

o

i

a

s

d

f

2

- 1 -

INDEX PAGE

Intended Usage 3

Safety instructions 3

Items supplied 4

Technical Data 4

Description of the appliance 5

Bringing the upper blade into a rest position 5

Needle Information 5

Upper looper element 5

Opening the front flap 6

Preparation 6

Connecting the foot pedal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Controlling the sewing speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Safety switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Fitting the waste container . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Removing needle(s) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Inserting needle(s) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Operating the handwheel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Adjusting the thread tree . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Threading 8

General instructions for threading . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Threading the upper looper thread (red) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Threading the lower looper thread (yellow) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Threading yarn for the right needle (green) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Threading yarn for the left needle (blue) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

Trial run . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

Changing threads (binding together) 15

Set the stitch length 15

Setting the seam width 15

... by using the right or left needle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

... by turning the seam width adjustment knob . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

Setting the seam width adjustment knob . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

Adjust sewing foot pressure 16

Differential transport 17

Manner of operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

Gathered overlock seam - Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

Stretched overlock seam - Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

Free arm sewing 18

Read these operating instructions carefully before using the appliance for the first time and preserve this booklet for later reference. Pass this booklet on to

whoever might acquire the appliance at a future date.

- 2 -

Overlock seams 19

Roll hemmings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

Binding-off and sample sewing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

Recommended tension settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

2-thread overcast chain stitch (overlock) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

2-thread-overcast-stitch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

3-thread chain stitch (overlock) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

3 - thread - flatlock seam . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24

3-thread overcast chain stitch (overlock) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25

3-thread safety stitch, highly elastic, imitated . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26

4-thread safety stitch, highly elastic, imitated . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27

Roll hemmings 28

3-thread rolled hem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28

3-thread upper looper overcast rolled hem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28

2-thread rolled hem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29

2-thread lower looper overcast rolled hem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29

Flatlock decorative seams 30

Flatlock seam as assembly seam . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30

Flatlock seam as decorative seam . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31

Overlock blind hems 31

Pin tucks 31

Sewing corners 32

Outer corners . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32

Inner corners . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32

Tips and Tricks 33

Using pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33

Secure empty threads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33

Seam reinforcement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33

Edging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33

Maintenance and Cleaning 34

Cleaning and lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34

Exchanging the lower blade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34

Storage 35

Disposal 35

Warranty and Service 35

Importer 35

Troubleshooting 36

- 3 -

Intended Usage

This overlock sewing machine is intended ...

- for use as a portable machine,

– for the trimming of material edges (sewing) of typical household

textiles, and ...

– only for domestic household use.

Safety instructions

Like any other electrical device, a sewing machine can cause serious, even

life-threatening injuries. To avoid these, and to work safely:

• Always disconnect the power supply when leaving the machine unattended.

This will prevent the risk of accidents if the machine is switched on

accidentally.

• Always first disconnect the power plug before carrying out maintenance

work on the machine. This will prevent possibly life-threatening electric

shocks. The LED light is not exchangeable.

• Do not pull the plug out of the wall socket by the lead. When pulling

out the plug, always hold the plug, not the lead.

• Only use the sewing machine in dry rooms.

• Arrange for defective power plugs and/or cables to be replaced at

once by qualified technicians or our Customer Service Department.

• This appliance is not intended for use by individuals (including children) with

restricted physical, physiological or intellectual abilities or deficiences in

experience and/or knowledge unless they are supervised by a person

responsible for their safety or receive from this person instruction in how

the appliance is to be used.

• Children should be supervised to ensure that they do not play with

the appliance.

• Never use the machine when the ventilation apertures are blocked.

Keep the ventilation apertures of the machine and the foot switch free

from fluff, dust and waste material.

• Should the cable connected to the foot pedal become damaged,

to avoid potential risks it must be replaced by the manufacturer, his

customers services or a similarly qualified person.

OVERLOCK SEWING MACHINE

This overlock sewing machine is not intended ...

- to be installed at a permanent location,

– for the processing of other materials (e.g. leather, canvas, sailcloth

and other heavy materials),

- for commercial or industrial use.

Warning about injuries and material damages:

• Keep your work space tidy. An untidy workplace can lead to accidents.

• Provide adequate lighting when working!

• Do not wear loose clothing or jewellery, as these can be caught in

moving parts. You should also wear a hair net if you have long hair.

• Avoid adopting an unusual posture. Remain steady and in a well-balanced

position at all times.

• If accidents occur as a result of handling the machine with insufficient

care, or failure to follow the safety instructions in this manual, then the

manufacturer cannot accept liability.

• Never cover the ventilation slots! Risk of overheating!

• Keep the sewing machine oil well away from children.

• If swallowed, or should eye contact be made with the sewing machine

oil, consult a doctor immediately.

- 4 -

Items supplied

Overlock Sewing Machine

Oil

Waste container

Accessory box

Operating instructions

The accessories are to be found in the accessory box on the side

of the machine (Fig.1.).

Technical Data

Number of threads 2, 3 or 4

Number of needles 2 or 1

Sewing speed approx. 1200 rpm

Stitch width

right: 3.0 mm - 4.5 mm

left: 5.2 mm - 6.7 mm

Stitch length 1 – 4 mm

Needles HA x 1 Nr. 11-14 or 130/705 Nr. 75-90

Power consumption : Motor: 90 W

Rated voltage: 220 - 240 V

~

, 50Hz

Protection class: II

Replacement blade

(bottom)

2 Needles Nr. 11

4 Needles Nr. 14

(2 in the machine,

pre-installed)

4 Bobbin caps

Upper looper element

Screwdriver small

Screwdriver large

Covering hood

Tweezers

Brush with integrated

unstitcher

The sound intensity level under normal operating conditions amounts to

78dB(A).

Foot pedal

Use only the foot pedal originally supplied with this sewing machine:

- ELECTRONIC FDM Speed Controller

- Type KD - 2902

Fig. 1

- 5 -

Description of the appliance

1 Thread tree

2 Spool support

3 Thread roll centerer

4 Sewing foot lever

5 Adjustment wheel for stitch length

6 Handwheel

7 Connection Footpedal/Power supply

8 Power switch (On/Off switch)

9 Differential transport lever

0 Front flap

q Support plate of the seam width finger

w Free arm

e Stitch plate

r Thread tension selector (left needle)

t Thread tension selector (right needle)

z Thread tension selector (upper looper)

u Thread tension selector (lower looper)

Bringing the upper blade into a rest position

To make certain types of seam, or to more easily operate the adjustment

wheel for cutting width f, you must bring the upper blade i into a

rest position.

For this, press the upper blade i to the right and rotate it a little, so

that it is firmly seated (Fig. 2 and 3).

Needle Information

This machine uses standard commercial flat-shaft needles for sewing machines.

These prevent the incorrect insertion of the needle. You can purchase these

needles in any specialist shop.

You can use needles of the sizes 11 and 14 in this machine.

The adjoining table gives you a brief overview of the differences when using a

needle (for detailed information, see "Setting the seam width).

Upper looper element

For some kinds of stitches you will need to use the upper looper element.

When you need to insert it is described in the individual stitches.

Insert the small wire from behind in the eyelet of the upper looper o and

the plastic bolt, on the other end and from the front, in the hole in the upper

looper o (Fig. 4a).

You can store the upper looper ready for use in the slot behind the front

flap 0 (Fig. 4b).

i movable upper blade (Upper blade)

o Upper looper

p Lower looper

a Sewing foot

s Fixed lower blade

d Seam width switch

f Seam width adjustment knob

Fig. 2

Fig. 3

Fig.4a

Fig.4b

Seam width 3.5 mm 5.7 mm

Employed needle right needle left needle

Thread tension selector green blue

- 6 -

Opening the front flap

Attention!

Always switch the machine off with the power switch 8 when you open

the front flap 0. Risk of Injury!

• Slide the front flap 0 to the right (A) and then pull it towards you (B)

(Fig. 5).You will see the upper looper behind the front flap 0.

Note:

While sewing, the front flap 0 must be kept closed!

Preparation

Place the overlock sewing machine on a stable and level surface.

Ensure there is sufficient illumination at your workplace.

Connecting the foot pedal

• Insert the plug of the foot pedal into the socket for the foot pedal 7.

• Insert the plug into a power socket.

To switch the machine on, press the power switch 8.

Attention!

During absences from the machine or when doing maintenance work,

always remove the plug from the mains power socket. Risk of Injury!

Controlling the sewing speed

The sewing speed is controlled by means of the footpedal. The sewing

speed is changed by applying more or less pressure to the footpedal.

Safety switch

This machine is fitted with a micro safety switch. You cannot start the machine

if the front flap 0 is open. Close the front flap 0 before you start to sew.

Fitting the waste container

The waste container collects remnants during sewing, so that your workplace

stays tidy.

• First push the two restraints (A) into the receiving holes (B) (Fig. 6).

• Then guide the two restraints (C) into the receiving holes (D) (Fig. 7).

• To remove the waste container, pull it forward and then tilt it slightly

(Fig. 8).

Fig. 5

Fig. 8

Fig. 7

Fig. 6

- 7 -

Removing needle(s)

Attention!

Before exchanging the needles, remove the power plug. This prevents an

unintended starting of the machine. If you do not, you run a risk of serious

injury!

Tip!

An exchange of the needles is easier if you first remove the free arm cover

(Fig. 9a)!

1. Turn the handwheel 6 towards yourself until the needles are in the

highest position (Fig. 9b)

2. Loosen the needle retaining screws with the small screwdriver until the

needles are free (Fig. 10).

3. Remove the needles.

Inserting needle(s)

Attention!

Before exchanging the needles, remove the power plug. This prevents an

unintended starting of the machine. If you do not, you run a risk of serious

injury!

1. Hold the needle with the flattened side to the rear.

2. Push the needle as far as it will go into the needle holder.

3. Firmly tighten the needle screws with the small screwdriver (Fig. 10).

Operating the handwheel

Note:

Always turn the handwheel 6 only towards yourself (Fig. 9b).

Adjusting the thread tree

• Completely remove the thread tree 1 before threading (Fig. 11).

• Turn the thread tree 1 so that the thread guides stand exactly above

the spool supports 2.

• In the correct position, the two jointed parts of the thread tree 1 snap

audibly into position.

• Place the thread rolls on the thread roll centrings.

If you do not use industrial coils, remove the thread roll centrings. Slide

a spool cap onto each of the thread rolls (Fig. 12). This will hold them in

place when sewing.

Fig.10

Fig. 11

Fig. 12

Fig.9b

Fig.9a

- 8 -

Threading

Note:

On delivery, all 4 threads are already threaded. You can begin sewing im-

mediately. Should you wish to change the thread, and all 4 threads are still

threaded, then proceed as described in the chapter "Changing threads

(binding together)“.

Should you need to rethread all threads from scratch, then proceed as

described in this chapter, "Threading“.

General instructions for threading

Attention!

Before threading, ALWAYS place the power switch 8 at "O" (Off) and

remove the plug from the mains power socket. This prevents an unintended

starting of the machine. If you do not, you run a risk of serious injury!

Correct threading is important, so that the stitches are not irregular and that

the yarn does not break.

Behind the front flap 0 there is a diagram with instructions for threading.

Additionally, the thread guides are marked in various colours.

In the accessory box you will find tweezers, the use of which helps make

threading easier.

Threading is done in this order (Fig. 13/14):

1. First step: Upper looper (red)

2. Second step: Lower looper (yellow)

3. Third step: Thread for the right needle (green)

4. Fourth step: Thread for the left needle (blue)

Note:

When all threads are threaded, and the lower looper thread loosens itself,

proceed as follows:

• Unthread the two threads of the needles.

• Then thread the lower looper thread.

• First then rethread the threads of the two needles again.

The needles must always be the last to be threaded!

For simplification, the individual steps are numbered on the drawings.

Threading the upper looper thread (red)

Attention!

Before threading, ALWAYS place the power switch 8 at "O" (Off) and

remove the plug from the mains power socket. This prevents an unintended

starting of the machine. If you do not, you run a risk of serious injury!

Always use the accompanying drawings for assistance.

Figure 15 shows the thread path of the upper looper thread. The individual

threading positions are numbered and described in detail in the following.

1. Open the front flap 0.

2. Guide the yarn from back to front through the thread tree 1 (1).

143 2

Fig. 13

Fig. 14

Fig. 15

- 9 -

3. Thread the yarn into the thread guide in that you pull the thread down

until it slips under the thread guide (2) (Fig. 16).

4. Firmly hold the yarn with your fingers, guide it between and through

the discs of the thread tension selector z and then pull it down (3)

(Fig. 17).

Note:

The yarn must lie correctly between the two discs of the thread tension

selector z.

5. Thread the yarn in the looper area as per the red markings (Fig. 18).

6. Pull the thread from back to front through the upper looper o.

7. Pull around 10 cm of thread through the looper and place it behind

the stitch plate e.

Fig. 16

Fig. 17

Fig. 18

- 10 -

Threading the lower looper thread (yellow)

Attention!

Before threading, ALWAYS place the power switch 8 at "O" (Off) and

remove the plug from the mains power socket. This prevents an unintended

starting of the machine. If you do not, you run a risk of serious injury!

Figure 19 shows the thread path of the lower looper thread. The individual

threading positions are numbered and described in detail in the following.

1. Guide the yarn from back to front through the thread tree 1 (1).

2. Thread the yarn into the thread guide in that you pull the thread down

until it slips under the thread guide (2) (Fig. 20).

3. Firmly hold the yarn with your fingers, guide it between and through

the discs of the thread tension selector u and then pull it down (3)

(Fig. 21).

Note:

The yarn must lie correctly between the two discs of the thread tension

selector u.

4. Turn the handwheel 6 to yourself until the lower looper p is at the

far right.

Fig. 20

Fig. 21

Fig. 19

- 11 -

5. Thread the yarn in the looper area as per the yellow markings (4 - 8)

(Fig. 22).

6. Firmly hold the yarn with the tweezers about 4 cm from the thread

guide (Fig. 23).

7. Now guide it lightly, from the left and with the tweezers, under the

thread guide.

8. Pull the yarn upwards into the thread guide (9).

9. Lead the yarn to the rear and over the upper end of the lower looper p

(10A) (Fig. 23).

10. Then, carefully pull the yarn down so that it slides into the recess of

the looper (10B) (Fig. 23). For this step also use the drawing which

is attached to the machine!

11. Guide the thread through the looper eyelet (11). The yarn should run

in the groove of the lower looper p (Fig. 23).

12. Draw around 10 cm of yarn through the looper and place it to the

rear

over

the upper looper o and the stitch plate e.

Threading yarn for the right needle (green)

Attention!

Before threading, ALWAYS place the power switch 8 at "O" (Off) and

remove the plug from the mains power socket. This prevents an unintended

starting of the machine. If you do not, you run a risk of serious injury!

Figure 24 shows the thread path of the right needle thread. The individual

threading positions are numbered and described in detail in the following.

1. Guide the yarn from back to front through the thread tree 1 (1).

9

8

10

11

Fig. 22

Fig. 23

Fig. 24

- 12 -

2. Thread the yarn into the thread guide in that you pull the thread down

until it slips under the thread guide (2) (Fig. 25).

3. Firmly hold the yarn with your fingers, guide it between and through

the discs of the thread tension selector t and then pull it down (3)

(Fig. 26).

Note:

The yarn must lie correctly between the two discs of the thread tension

selector t.

4. Thread the yarn as per the green markings (4- 7) (Fig. 27/28).

5. Thread the yarn through the right needle (8) (Fig. 28).

6. Lay the yarn to the rear under the sewing foot a.

Fig. 25

Fig. 26

Fig. 27

Fig. 28

5

6

- 13 -

Threading yarn for the left needle (blue)

Attention!

Before threading, ALWAYS place the power switch 8 at "O" (Off) and

remove the plug from the mains power socket. This prevents an unintended

starting of the machine. If you do not, you run a risk of serious injury!

Figure 29 shows the thread path of the left needle thread. The individual

threading positions are numbered and described in detail in the following.

1. Guide the yarn from back to front through the thread tree 1 (1).

2. Thread the yarn into the thread guide in that you pull the thread down

until it slips under the thread guide (2) (Fig. 30).

3. Firmly hold the yarn with your fingers, guide it between and through

the discs of the thread tension selector r and then pull it down (3)

(Fig. 31).

Note:

The yarn must lie correctly between the two discs of the thread tension

selector r.

Fig. 29

Fig. 30

Fig. 31

- 14 -

4. Thread the yarn as per the blue markings (4 - 6) (Fig. 32/33).

5. Thread the yarn through the left needle (7) (Fig. 33).

6. Lay the yarn to the rear under the sewing foot a.

Trial run

When yarn has been threaded for the first time, or after a yarn breakage

it must be rethreaded, proceed as follows:

Lift the sewing foot a.

Hold the ends of the threads between the fingertips of your left hand, slow-

ly turn the handwheel 6 two or three times towards yourself and

then check the threads once again.

Lay the material for a trial run under the sewing foot a and slowly start

to sew.

The material will be automatically fed through.

When the task is complete, continue sewing until an approximately

5cm (2") long length of threads has formed at the end of the material.

Cut through the threads with scissors.

Fig. 32

Fig. 33

4

5

- 15 -

Changing threads (binding together)

Changing threads is quite simple with the following procedure:

1. Cut the yarn above the spool support 2 (Fig. 34) and place the new

roll of thread on the spool support 2.

2. Tie the ends of the new and the old thread together (Fig. 35).

3. Place the thread tension selector r/t/z/u at "0" (Fig. 36) and lift

the sewing foot a.

4. Pull on the other end of the yarn until the knot passes under the sewing

foot a.

5. For threading it in the needle, pull on the other end until the knot is in

the eye of the needle and then cut the yarn to the left and right of the

knot. Then carry out the rethreading.

Set the stitch length

The stitch length can be adjusted from 1.0 to 4.0 mm. Almost all overlock

work is carried out with a stitch length of 2.5 – 3.5 mm.

Turn on the adjustment wheel for stitch length 5 (Fig. 37) to adjust the

stitch length:

• A stitch length of 3 mm is recommended for most sewing.

• For the working of heavy fabrics, a stitch length of 4 mm is to be re-

commended.

• For the working of light fabrics, a stitch length of 2 mm is to be re-

commended..

With these settings you will produce respectable seams and the fabric

will not be crimped.

Setting the seam width

The width of seams can be determined both by changing the needle position

and via the seam width adjustment knob f.

... by using the right or left needle

The width of the seam can be determined by using the left or the right

needle.

• Only the left needle is used: 5.7 mm

• Only the right needle is used: 3.5 mm

Fig. 34

Fig. 35

Fig. 36

Fig. 37

- 16 -

... by turning the seam width adjustment knob

By using the seam width adjustment knob f, seam width can be adjusted

within the ranges indicated below.

• Only the left needle is used: 5.2 - 6.7 mm

• Only the right needle is used: 3.0 - 4.5 mm

Setting the seam width adjustment knob

Attention!

Before making adjustments with the seam width adjustment knob f

always place the mains switch 8 at the position "O" (Off). This prevents

an accidental start of the appliance and thus the risk of injury!

• Open the front flap 0, this can make the adjustment easier to carry out.

• Turn the seam width adjustment knob f to the desired seam width

(Fig. 38). Orientate yourself on the scale on the stitch plate e

(Fig. 39).

Adjust sewing foot pressure

Upon delivery, the sewing foot pressure is set for medium-weight materials.

If you wish to use heavier or lighter materials, adjust the sewing foot pressure

as follows:

• For lighter fabrics, you need to reduce the pressure.

• For heavier fabrics, you need to increase the pressure.

Insert the small screwdriver into the hole on the upper side of the machine

(Fig. 40). The pressure adjustment screw is located here (A). Ensure that the

screwdriver slips into the slot of the pressure adjustment screw (B) (Fig. 41).

• Turn the screwdriver in the direction "+" if you want to increase the pressure.

• Turn the screwdriver in the direction "-" if you want to reduce the pressure.

Note:

To return to the factory-set default sewing foot pressure, turn the pressure

adjustment screw as far as it will go anti-clockwise (-). Then turn it 6 rotations in

a clockwise (+) direction.

The standard sewing foot pressure is reset.

Fig. 38

Fig. 39

Fig. 40

Fig. 41

- 17 -

Differential transport

Manner of operation

The machine has two sets of toothed rack feeders, one to the front and one

to the rear. Both sets move independant of each other. Through the differential

feed motion both toothed rack sets can move themselves at various speeds.

With this, the fabric is stretched or gathered, depending on which transport

differential has been set between the front and rear rack feeders.

With the aid of the differential transport, interesting effects can be achie-

ved when sewing overlock seams on stretch materials and diagonally cut

fabrics (Fig. 43).

Note:

When the differential transport lever 9 stands at "1.0", that corresponds

to a differential transport ratio of 1:1. Both toothed feed racks move at the

same rate (Fig. 42).

The differential transport lever 9 can be adjusted in a range from 1:0.7

to 1:2.0.

Gathered overlock seam - Settings

The gathered overlock seam is suitable for the ruffling of sleeves, back

upper parts, skirt seams etc.made of elastic materials such as knitwear

and jersey. The individual parts should be brought together before sewing.

• Adjust the differential transport lever 9 to a value higher than 1.0

(Fig. 44). The exact setting depends on the material to be processed

and the desired level of ruffling or gathering.

Therefore always do a sample stitching to test the settings.

Stretched overlock seam - Settings

The stretched overlock seam is suitable for the manufacture of ruffles at the

collar, cuffs and skirt edges etc. in soft, stretchy fabric and knitwear.

• Adjust the differential transport lever 9 to a value lower than 1.0 (Fig.

45). The exact setting depends on the material to be processed, and

on the strength of the desired "ruffle effect".

Therefore always do a sample stitching to test the settings.

• Hold the seam down with slight firmness before and behind the sewing

foot a so as to keep the textile under tension.

Note:

If you have set a value of "3" or higher on the adjustment wheel for the

stitch length 5, this setting will automatically return to "3" when you set the

differential transport lever 9 to 2.0.

Fig. 42

Fig. 43

Fig. 44

Fig. 45

- 18 -

Free arm sewing

To work tubular-shaped fabrics, such as sleeves or trouser legs, you can

remove the free arm cover.

• If appropriate, remove the waste container from the machine.

• Slide the free arm cover to the left and pull it off (Fig. 46)..

• You can now pull the textiles over the free arm w and work them

(Fig. 47).

• To replace the free arm cover, push it onto the free arm w until it clicks

into place and is firmly seated (Fig. 48).

Fig. 46

Fig. 47

Fig. 48

Sidan laddas ...

Silvercrest SON 90 A1 Operating Instructions Manual

Silvercrest SON 90 A1 Operating Instructions Manual

på andra språk

Relaterade papper

Andra dokument