Yamaha Audio WX-010BL Användarmanual

WX-010BL
Yamaha Audio
varumärke
Yamaha Audio
Modell
WX-010BL
Kategori
Kompletterande musikutrustning
Typ
Användarmanual
UABGLV
EN
OWNER'S MANUAL
Before using this unit, be sure to read the “Safety Brochure” and “Quick Manual.”
i
1 Read these instructions.
2 Keep these instructions.
3 Heed all warnings.
4 Follow all instructions.
5 Do not use this apparatus near water.
6 Clean only with dry cloth.
7 Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
8 Do not install near any heat sources such as radiators,
heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
9 Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two
blades with one wider than the other. A grounding
type plug has two blades and a third grounding
prong. The wide blade or the third prong are provided
for your safety. If the provided plug does not fit into
your outlet, consult an electrician for replacement of
the obsolete outlet.
10 Protect the power cord from being walked on or
pinched particularly at plugs, convenience
receptacles, and the point where they exit from the
apparatus.
11 Only use attachments/accessories specified by the
manufacturer.
12 Use only with the cart, stand, tripod,
bracket, or table specified by the
manufacturer, or sold with the
apparatus. When a cart is used, use
caution when moving the cart/apparatus
combination to avoid injury from tip-over.
13 Unplug this apparatus during lightning storms or
when unused for long periods of time.
14 Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate
normally, or has been dropped.
Yamaha and the Electronic Industries Association’s Consumer Electronics Group want you to get the most out
of your equipment by playing it at a safe level. One that lets the sound come through loud and clear without
annoying blaring or distortion – and, most importantly, without affecting your sensitive hearing. Since hearing
damage from loud sounds is often undetectable until it is too late, Yamaha and the Electronic Industries
Association’s Consumer Electronics Group recommend you to avoid prolonged exposure from excessive
volume levels.
IMPORTANT SAFETY INSTRUCTIONS
CAUTION
RISK OF ELECTRIC SHOCK DO
NOT OPEN
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
• Explanation of Graphical Symbols
The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended to
alert you to the presence of uninsulated
“dangerous voltage” within the product’s
enclosure that may be of sufficient magnitude
to constitute a risk of electric shock to
persons.
The exclamation point within an equilateral
triangle is intended to alert you to the
presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
IMPORTANT
Please record the serial number of this unit in the space
below.
MODEL:
Serial No.:
The serial number is located on the rear of the unit. Retain
this Owner’s Manual in a safe place for future reference.
We Want You Listening For A Lifetime
ii
This device complies with part 15 of FCC Rules and Industry Canada’s licence-exempt RSSs. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
FCC INFORMATION (for US customers)
1 IMPORTANT NOTICE: DO NOT MODIFY THIS
UNIT!
This product, when installed as indicated in the
instructions contained in this manual, meets FCC
requirements. Modifications not expressly approved
by Yamaha may void your authority, granted by the
FCC, to use the product.
2 IMPORTANT: When connecting this product to
accessories and/or another product use only high
quality shielded cables. Cable/s supplied with this
product MUST be used. Follow all installation
instructions. Failure to follow instructions could void
your FCC authorization to use this product in the
USA.
3 NOTE: This product has been tested and found to
comply with the requirements listed in FCC
Regulations, Part 15 for Class “B” digital devices.
Compliance with these requirements provides a
reasonable level of assurance that your use of this
product in a residential environment will not result in
harmful interference with other electronic devices.
This equipment generates/uses radio frequencies and,
if not installed and used according to the instructions
found in the users manual, may cause interference
harmful to the operation of other electronic devices.
Compliance with FCC regulations does not guarantee
that interference will not occur in all installations. If
this product is found to be the source of interference,
which can be determined by turning the unit “OFF”
and “ON”, please try to eliminate the problem by
using one of the following measures:
Relocate either this product or the device that is being
affected by the interference.
Utilize power outlets that are on different branch
(circuit breaker or fuse) circuits or install AC line
filter/s.
In the case of radio or TV interference, relocate/
reorient the antenna. If the antenna lead-in is 300 ohm
ribbon lead, change the lead-in to coaxial type cable.
If these corrective measures do not produce
satisfactory results, please contact the local retailer
authorized to distribute this type of product. If you can
not locate the appropriate retailer, please contact
Yamaha Corporation of America A/V Division, 6660
Orangethorpe Ave., Buena Park, CA 90620.
The above statements apply ONLY to those products
distributed by Yamaha Corporation of America or its
subsidiaries.
NOTICE
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC/IC radiation exposure limits set forth for an uncontrolled environment and meets the
FCC radio frequency (RF) Exposure Guidelines and RSS-102 of the IC radio frequency (RF) Exposure rules. This
equipment should be installed and operated keeping the radiator at least 20cm or more away from person’s body.
This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.
FCC CAUTION
Change or modifications not expressly approved by the
party responsible for compliance could void the user’s
authority to operate the equipment.
FOR CANADIAN CUSTOMERS
To prevent electric shock, match wide blade of plug to
wide slot and fully insert.
CAN ICE-3 (B)/NMB-3 (B)
iii
1 To assure the finest performance, please read this
manual carefully. Keep it in a safe place for future
reference.
2 Install this unit in a well ventilated, cool, dry, clean
place – away from direct sunlight, heat sources,
vibration, dust, moisture and cold. For proper
ventilation, allow the following minimum clearances.
Top: 5 cm (2 in)
Rear: 5 cm (2 in)
Sides: 5 cm (2 in)
3 Locate this unit away from other electrical
appliances, motors, or transformers to avoid
humming sounds.
4 Do not expose this unit to sudden temperature
changes from cold to hot (or vice versa), and do not
locate this unit in an environment with high humidity
(i.e., a room with a humidifier) to prevent
condensation inside this unit, which may cause an
electrical shock, fire, damage to this unit, and/or
personal injury.
5 Avoid installing this unit where foreign object may
fall onto this unit and/or this unit may be exposed to
liquid dripping or splashing. On the top of this unit,
do not place:
– Other components, as they may cause damage
and/or discoloration on the surface of this unit.
– Burning objects (i.e., candles), as they may cause
fire, damage to this unit, and/or personal injury.
– Containers with liquid in them, as they may fall
and liquid may cause electrical shock to the user
and/or damage to this unit.
6 Do not cover this unit with a newspaper, tablecloth,
curtain, etc. in order not to obstruct heat radiation. If
the temperature inside this unit rises, it may cause
fire, damage to this unit, and/or personal injury.
7 Do not plug in this unit to a wall outlet until all
connections are complete.
8 Do not operate this unit upside-down. It may
overheat, possibly causing damage.
9 Do not use force on switches, knobs and/or cords.
10 When disconnecting the power cable from the wall
outlet, grasp the plug; do not pull the cable.
11 Do not clean this unit with chemical solvents; this
might damage the finish. Use a clean, dry cloth.
12 Only voltage specified on this unit must be used.
Using this unit with a higher voltage than specified is
dangerous and may cause fire, damage to this unit,
and/or personal injury. Yamaha will not be held
responsible for any damage resulting from use of this
unit with a voltage other than specified.
13 To prevent damage by lightning, keep the power
cable and outdoor antennas disconnected from a wall
outlet or this unit during a lightning storm.
14 Do not attempt to modify or fix this unit. Contact
qualified Yamaha service personnel when any
service is needed. The cabinet should never be
opened for any reasons.
15 When not planning to use this unit for long periods of
time (i.e., vacation), disconnect the AC power plug
from the wall outlet.
16 Be sure to read the “TROUBLESHOOTING” section
on common operating errors before concluding that
this unit is faulty.
17 Before moving this unit, press to set the unit to
off, and disconnect the AC power plug from the wall
outlet.
18 Condensation will form when the surrounding
temperature changes suddenly. Disconnect the power
cable from the outlet, then leave this unit alone.
19 When using this unit for a long time, this unit may
become warm. Turn the unit off, then leave this unit
alone for cooling.
20 Install this unit near the wall outlet and where the AC
power plug can be reached easily.
21 Be sure to use the power cable supplied with this
unit. Using a power cable other than the one provided
may cause fire or damage to this unit.
◆ For U.K. customers
If the socket outlets in the home are not suitable for the
plug supplied with this appliance, it should be cut off and
an appropriate 3 pin plug fitted. For details, refer to the
instructions described below.
The plug severed from the mains lead must be destroyed, as a
plug with bared flexible cord is hazardous if engaged in a live
socket outlet.
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.
This unit is not disconnected from the AC power source
as long as it is connected to the wall outlet, even if this
unit itself is turned off by . In this state, this unit is
designed to consume a very small quantity of power.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR
MOISTURE.
• This unit’s speakers use magnets. Do not place items
that are sensitive to magnetism, such as CRT-type TVs,
clocks, credit cards, floppy disks, etc., on or beside this
unit.
• There is a chance that placing this unit too close to a
CRT-based (Braun tube) TV set might impair picture
color. Should this happen, move this unit away from the
TV set.
iv
◆ Special Instructions for U.K.
Model
About this manual
• “iPhone” described in this manual may also refer to “iPod”
or “iPad.”
• Illustrations may differ from actual item depicted.
• Symbols:
Indicates precautions for use of the unit and its
feature limitations.
Indicates supplementary explanations for better
use.
Indicates the corresponding reference page(s).
IMPORTANT
THE WIRES IN MAINS LEAD ARE
COLOURED IN ACCORDANCE WITH THE
FOLLOWING CODE:
Blue: NEUTRAL
Brown: LIVE
As the colours of the wires in the mains lead of this
apparatus may not correspond with the coloured
markings identifying the terminals in your plug,
proceed as follows:
The wire which is coloured BLUE must be
connected to the terminal which is marked with the
letter N or coloured BLACK. The wire which is
coloured BROWN must be connected to the
terminal which is marked with the letter L or
coloured RED.
Make sure that neither core is connected to the
earth terminal of the three pin plug.
Information for Users on Collection
and Disposal of Old Equipment:
This symbol on the products, packaging,
and/or accompanying documents means
that used electrical and electronic products
should not be mixed with general
household waste.
For proper treatment, recovery and
recycling of old products, please take them
to applicable collection points, in
accordance with your national legislation.
By disposing of these products correctly,
you will help to save valuable resources
and prevent any potential negative effects
on human health and the environment
which could otherwise arise from
inappropriate waste handling.
For more information about collection and
recycling of old products, please contact
your local municipality, your waste
disposal service or the point of sale where
you purchased the items.
For business users in the European
Union:
If you wish to discard electrical and
electronic equipment, please contact your
dealer or supplier for further information.
Information on Disposal in other
Countries outside the European
Union:
This symbol is only valid in the European
Union. If you wish to discard these items,
please contact your local authorities or dealer
and ask for the correct method of disposal.
If there should be color blotching or noise when
used near a TV, move this unit away from the TV
when using it.
Do not use this unit within 22 cm (9 inches) of
persons with a heart pacemaker implant or
defibrillator implant.
Radio waves may affect electro-medical devices.
Do not use this unit near medical devices or inside
medical facilities.
The user shall not reverse engineer, decompile,
alter, translate or disassemble the software used in
this unit, whether in part or in whole. For
corporate users, employees of the corporation
itself as well as its business partners shall observe
the contractual bans stipulated within this clause.
If the stipulations of this clause and this contract
cannot be observed, the user shall immediately
discontinue using the software.
Note
y
☞
1
Smooth operation and wireless music playback using iPhone/Android
TM
devices
• By installing the free dedicated app “MusicCast CONTROLLER” on your iPhone/iPad/iPod touch or Android device, you
will be able to set up a network, make various settings, and select songs to play back. You can also use these devices as a
remote controller (☞ P.7).
• Equipped with Wi-Fi, which allows the unit to connect to the wireless router (access point) without any cables.
Plays various supported content with high quality sound
• Plays music from DLNA servers/Internet radio (☞ P.17), AirPlay and Bluetooth.
• Rich sound provided by the two-way speaker, large passive radiator, and DSP (Digital Signal Processor) developed by
Yamaha.
• Enhanced treble and thick mid/bass sound, even when playing a compressed audio source, such as MP3. (Music Enhancer)
Supports streaming services
• You can enjoy music from a variety streaming services. (Supported music streaming services vary by the country or region of
use.)
Stereo Pair function
• You can enjoy stereo reproduction using two WX-010 units.
FEATURES
WX-010
2
INTRODUCTION
SUPPLIED ACCESSORIES...................................2
PART NAME ..........................................................3
PREPARATION
INSTALLATION .....................................................4
Mounting the unit on a wall
(Except for U.S.A. and Canada model)..........4
TURNING ON THE POWER ..................................5
CONNECTING TO THE NETWORK ......................6
HOME AUDIO NETWORK WITH MusicCast........7
Connecting to the network using MusicCast
CONTROLLER ..............................................7
CONNECTING TO THE NETWORK BY
SHARING THE iOS DEVICE SETTING .................9
LISTENING TO THE MUSIC
LISTENING TO THE INTERNET RADIO.............10
LISTENING TO THE SONGS IN THE
COMPUTER AND NAS ........................................10
Setting the media sharing of music files...........10
PLAYING BACK MUSIC WITH AirPlay ..............11
Playback of iTunes/iPhone music contents......11
Clearing AirPlay................................................11
LISTENING TO MUSIC FROM YOUR Bluetooth
DEVICE ................................................................12
Pairing this unit with your Bluetooth device......12
Connecting an already-paired device via
Bluetooth......................................................12
Disconnecting a Bluetooth connection .............12
Listening to music through wireless
headphones .................................................13
OTHER FUNCTIONS AND
INFORMATION
STEREO PAIR .....................................................14
Setting/Playing back music ..............................14
Canceling Stereo Pair ......................................15
UPDATING THE FIRMWARE ..............................16
OPTION SETTINGS .............................................16
ADDITIONAL INFORMATION .............................17
TRADEMARKS ....................................................17
TROUBLESHOOTING .........................................18
General.............................................................18
MusicCast.........................................................18
Network ............................................................18
Bluetooth ..........................................................20
SUPPORTED DEVICES/MEDIA AND FILE
FORMATS ............................................................21
SPECIFICATIONS................................................22
INTRODUCTION
CONTENTS
SUPPLIED ACCESSORIES
Power cable
Anti-vibration pad
y
To prevent the vibration from the sound from reaching
the wall, attach the Anti-vibration pads on the four
corners of the rear panel.
(Except for U.S.A.
and Canada model)
Quick Manual
Safety Brochure
3
■ Top panel
(power)/CONNECT (☞ P.5, 7)
Turns down the volume.
Turns up the volume.
Plays/pauses.
Bluetooth indicator
Lights during Bl uetooth connection.
Power indicator
Lights while the unit is turned on.
Wi-Fi indicator
Lights while the unit is connected to the wireless (Wi-Fi)
network.
y
, , , are touch sensors. They react when you touch them with your finger.
If the volume reaches the maximum/minimum value, these three indicators (
, , ) flash twice at the same time.
■ Rear panel
Key hole slot (☞ P.4)
(Except for U.S.A. and Canada model)
Wall mount hanger hole (☞ P.5)
Use to mount the unit to a wall mount hanger.
Power connector (☞ P.5)
Network terminal (☞ P.6)
Use a network cable (commercially available) to connect
to the network.
y
If you use the unit with Wi-Fi, a network cable is not
necessary to connect to the unit.
PART NAME
Note
4
PREPARATION
Plug the power cable into the wall outlet after completing installation.
• Placing the unit too close to a CRT TV may impair the picture color or cause a buzzing noise. In this case, move the unit at
least 20 cm (8") away from the TV. This is not an issue with LCD and plasma TVs.
• Install in a stable place, being careful of the following points:
– Do not place on top of steel or other metal plates.
– Do not cover with a cloth, etc.
You can mount the unit on the wall as follows.
Install screw (commercially available) into a solid wall or wall support as shown in the illustration. Use 3.5 to 4 mm (1/8")
diameter self-tapping screw.
Hang the unit by its keyhole slot onto the protruding screw.
• Make sure the shaft of the screw is seated in the narrow part of the keyhole slot. Otherwise, the unit may fall.
• Do not mount the unit on thin plywood or on a wall with a soft surface material. Otherwise, the screw may pull out of the
surface and the unit may fall, possibly damaging the unit or causing personal injury.
• Do not affix the unit to a wall using nails, adhesives, or unstable hardware. Long-term use and vibration may cause the unit to
fall.
• To avoid accidents resulting from tripping over loose cables (such as a power cable), affix the cables to the wall.
• When using the brackets to mount the unit on a wall / ceiling, please use safety wire (not included) between the unit and the
bracket to prevent the unit from falling.
• If you are not sure of a safe way to install the unit, consult a professional installer or a building contractor.
• To prevent the vibration from the sound from reaching the wall, attach the Anti-vibration pads on the four corners of the rear
panel (☞ P.2).
INSTALLATION
Note
Mounting the unit on a wall (Except for U.S.A. and Canada model)
Wall/wall support
Minimum
20 mm (3/4")
5 mm
(1/4")
WX-010
1.7 kg (3.7 lbs.)
Note
TURNING ON THE POWER
5
■ To mount the unit to a wall mount hanger
The unit can be mounted to the wall using a commerciallyavailable wall mount hanger. Use the wall mount hanger hole on the
rear panel to mount.
y
Use a wall mount hanger that is compatible for a unified coarse screw, such as those used for the tripod stand of a camera.
• If using a wall mount hanger, use the one compatible for this unit.
• Use the wall mount hanger whose withstand load capacity is over 4.5 kg (10 lbs.).
• Follow the instructions in the owner’s manual of the wall mount hanger and mount the unit correctly.
• If you mount the unit incorrectly or use a wall mount hanger that is not compatible for the unit, the unit may fall and cause
injury.
• Check the safety after mounting the unit. Yamaha is not responsible for any accidents which may be caused due to an
incorrect installation position or incorrect installation methods, or for any malfunction of the wall mount hanger. If you are
worried about the safety, ask a professional to install.
Rear panel
120 mm (4-3/4")
60 mm (2-3/8")
58mm
(2-1/4")
WX-010
1.7 kg
(3.7 lbs.)
160 mm (6-1/4")
Minimum
5 mm (1/4")
Specification of mounting screw:
UNC 1/4-20
Specifications of the screw hole
Diameter 6.35 mm (1/4")
Screw thread 20 (per 1")
Diameter 6.35 mm (1/4")
Depth 9 mm (3/8")
WX-010
Note
TURNING ON THE POWER
Plug the power cable into the wall outlet and
tap (power)/CONNECT.
The unit turns on and the power indicator lights. If you
tap again, the unit turns off (standby) and the power
indicator turns off.
• After the power plug is inserted into the wall outlet, it
takes about 10 seconds for the touch sensors to be
adjusted. In order to prevent malfunction of the touch
sensors, do not touch them ( (power)/CONNECT/
// ) or play back for about 10 seconds.
y Auto Standby
If about 20 minutes have elapsed with no playback and no
operation while the unit is on, it will automatically enter
standby.
You can change the auto standby function setting in the
MusicCast CONTROLLER app (☞ P.7). Tap
(Settings) in the room select display, and then change the
setting.
Power cable
Power indicator
Tap (power)/CONNECT.
Rear pannel
Top pannel
Note
6
Connect the unit to the network as shown below.
y
• For details on Internet connection, refer to the owner’s manuals of your connecting devices.
• Some security software installed on your PC or the firewall settings of connecting devices (such as a router) may block the
access of the unit to the connecting devices or the Internet. In this case, change the setting of the security software or
connecting devices.
• If you connect the unit to the network with a network cable, connect with a commercially available STP (shielded twisted
pair) network cable (straight, CAT-5 or higher).
• Using the MusicCast CONTROLLER app, make sure that the unit and other connecting devices are connected to the same
router (☞ P.7).
CONNECTING TO THE NETWORK
LAN
WAN
Internet
Modem
Wireless
router
This unit
Tablet
Smartphone
PC
NAS
(Network attached storage)
Network cable
Network cable
Wired or wireless
7
MusicCast is a brand new wireless musical solution from Yamaha, allowing you to share music among all of your rooms with a
variety of devices. You can enjoy music from your smartphone, PC, NAS drive and music streaming service anywhere in your
house with one easy-to-use app. For more details and a lineup of MusicCast compatible products, visit our website.
http://www.yamaha.com/musiccast/
■ MusicCast CONTROLLER
• Main functions
- Basic operations such as turning the unit on/off and,
volume adjustment
- Select/play/pause the music
- Play music in the devices
- Listening to the Internet radio
- Listening to the songs in the computer and NAS
- Playing back music with AirPlay
- Listening to music from your Bluetooth device
- Using the equalizer
- Using the sleep timer
- Updating the firmware
• System requirements
- For details, search App Store or Google Play
TM
for “MusicCast CONTROLLER.”
• The application supports iPhone/iPad/iPod touch and Android mobile devices.
For details, refer to the instructions for this app in each store.
- Wireless network environment.
■ Mobile device (smartphone, etc.)
To use the unit, you need the dedicated app “MusicCast CONTROLLER” for the operation.
HOME AUDIO NETWORK WITH MusicCast
Connecting to the network using MusicCast CONTROLLER
Install the MusicCast CONTROLLER app to
the mobile device.
Start the app.
After the app starts, select “Setup.”
y
If you have already connected a MusicCast compatible
device to the network, tap (Settings) in the room
select display and then add this unit as a new device.
Turn on the unit.
The power indicator lights.
Touch and hold the (power)/CONNECT
on the unit for 5 seconds.
The Wi-Fi and the Bluetooth indicators flash quickly.
Follow the guidance displayed in the app to set.
Follow the instructions in the MusicCast
CONTROLLER app to play music.
(power)/
CONNECT
Wi-Fi indicator
Bluetooth indicator
Power indicator
If your router supports multiple SSID’s (network names), connect the mobile device to the first access point (“SSID 1”,
etc.)
HOME AUDIO NETWORK WITH MusicCast
8
■ Setting of the devices and playback
Create the following network (MusicCast Network) using the MusicCast CONTROLLER app.
y
If you want to install a MusicCast compatible device to a location that is out of range of the wireless router, connect another
MusicCast support device to the router with a network cable to extend the range (Extend mode).
Depending on where it is placed, the MusicCast compatible device may not be able to play back a high-resolution audio source.
In this case, connect the device directly to the router with a network cable.
WX-010
Wireless router
Standard Mode
Extend Mode
WX-010
WX-010
9
When you turn on the unit for the first time after purchase or initialize the unit (☞ P.16), the Wi-Fi indicator blinks and the unit
automatically starts to search iOS device (such as iPhone). You can easily setup a wireless connection by applying the network
settings on iOS devices.
Before proceeding, confirm that your iOS device is connected to a wireless router (access point).
This setting does not need to be specified if the unit is connected to a network with “MusicCast CONTROLLER.”
Display the Wi-Fi setup screen on the iOS device and select the unit from “SETUP A NEW
AIRPLAY SPEAKER...”.
• Follow the on-screen instructions displayed on the iOS device.
• In order to enjoy all of the unit’s functions, connect it to a network with “MusicCast CONTROLLER.” (☞ P.7)
• You need iOS device with iOS 7.1 or later.
• The network settings on iOS devices cannot be applied to the unit to establish a wireless connection if your wireless router
(access point) uses WEP encryption.
CONNECTING TO THE NETWORK BY SHARING THE
iOS DEVICE SETTING
Note
10
LISTENING TO THE MUSIC
You can listen to world-wide radio stations via Internet. After connecting the unit to the network, use the MusicCast
CONTROLLER app (☞ P.7) to play the radio.
y
You can use the advanced feature of vTuner (such as adding a new station to the list) by accessing the following website with
the web browser on your PC.
http://yradio.vtuner.com/
- Before registering the Internet radio station, play any Internet radio station with this unit.
- To create a necessary account for registration, you need the vTuner ID of this unit and your e-mail address. You can check the
vTuner ID in the MusicCast CONTROLLER app. (☞ P.7)
Tap (Settings) in the room select display and then check the unit information.
This unit allows you to play back music files such as MP3, WMA, or FLAC (lossless audio data compression format) files
stored in the computer (server) connected to the network or NAS.
To play back music files in your computer with this unit, you need to make the media sharing setting between the unit and
computer (Windows Media Player 11 or later). The following instructions use Windows Media Player 12 in Windows 7 as an
example.
■ For Windows Media Player 12
LISTENING TO THE INTERNET RADIO
LISTENING TO THE SONGS IN THE COMPUTER AND NAS
Setting the media sharing of music files
Start Windows Media Player 12 on your PC.
Select “Stream”, then “Turn on media
streaming.”
The control panel window of your PC is shown.
Click “Turn on media streaming.”
Select “Allowed” from the drop-down list
next to “WX-010.”
y
The names on the list are device names (Room names).
You can set Room names on (Settings) in the room
select display. If the Room name is not set, the Room
name is “WX-010 ***.” (*** is an arbitrary number.)
Click “OK” to exit.
y
For details on media sharing settings, refer to Windows
Media Player help.
Turn on media streaming...
Turn on media streaming
Only setting the media sharing is explained in this section.
After setting, operate Windows Media Player with your
PC as usual to play back.
Allowed
PLAYING BACK MUSIC WITH AirPlay
11
Playing abundant supported contents with high quality sound from AirPlay.
The AirPlay function allows you to play back iTunes/iPhone music on the unit wirelessly via a network.
Follow the procedure below to play back iTunes/iPhone music contents on the unit.
Click/tap on the iTunes/iPhone screen and select a device other than WX-010 from the speaker list. Or, change the source
to other than AirPlay, using “MusicCast CONTROLLER.”
◆ For Windows Media Player 11
Start the Windows Media Player 11 on your PC.
Select “Library” then “Media Sharing.”
Check the “Share my media to” box, select the “WX-010” icon, and click “Allow.”
y
The names on the list are device names (Room names). You can set Room names on (Settings) in the room select
display. If the Room name is not set, the Room name is “WX-010 ***.” (*** is an arbitrary number.)
Click “OK” to exit.
◆ For a PC or a NAS with other DLNA server software installed
Refer to the owner’s manual of your device or software and configure the media sharing settings.
PLAYING BACK MUSIC WITH AirPlay
Playback of iTunes/iPhone music contents
Turn on the unit, and start iTunes on the PC
or display the playback screen on the
iPhone.
If the iTunes/iPhone recognizes the unit, the AirPlay
icon ( ) appears.
On the iTunes/iPhone, click (tap) the AirPlay
icon and select the unit (room name of the
unit) as the audio output device.
Select a song and start playback.
The source automatically switches to “AirPlay” and
playback starts (except in the eco standby).
Clearing AirPlay
iPhone
iTunes
(example)
iPhone iOS9
(example)
iTunes
(example)
iPhone iOS9
(example)
The unit’s room name is
displayed where “-------” is
indicated above.
12
This unit provides Bluetooth functionality. You can enjoy wireless music playback from your Bluetooth device
(smartphone, digital audio player, etc.). Please also refer to the owner’s manual of your Bluetooth device.
• Install in the same room as the device with which signals are to be exchanged (Bluetooth profile A2DP
compatible smartphone, digital audio player, etc.) within a direct line-of-sight distance of 10 m (33 ft).
• Make sure there are no obstacles between this unit and the Bluetooth device.
■ Pairing (Registration)
■ Connecting from the connecting device
In the Bluetooth settings of the connecting device, turn Bluetooth on.
From the Bluetooth connection list of the connecting device, choose this unit (the Room name of
this unit ☞ P.10).
The Bluetooth connection will be established, and the Bluetooth indicator will light.
If any of the following operations are performed while a Bluetooth connection is established, the Bluetooth
connection will be disconnected.
• Tapping (power)/CONNECT to enter standby.
• Touching and holding for 3 seconds.
• Disconnecting the Bluetooth connection from the connecting device.
LISTENING TO MUSIC FROM YOUR Bluetooth DEVICE
Pairing this unit with your Bluetooth device
Turn on the unit.
The power indicator lights.
On your connecting device (mobile device),
set Bluetooth to on.
Perform Bluetooth pairing on the connecting
device.
For details, refer to the owner’s manual of the connecting
device.
From the Bluetooth connection list of the
connecting device, choose this unit (the
Room name of this unit ☞ P.10).
y
• Finish the operation from turning on the unit to completing
pairing in 5 minutes.
• If you are asked to enter a password, enter the numerals
“0000.”
Connecting an already-paired device via Bluetooth
Disconnecting a Bluetooth connection
(power)/CONNECT
Power indicator
-------
4
The unit’s Room name is displayed where
“-------” is indicated above.
Check that the pairing process on the connecting device
has been completed. If the pairing process fails, start over
from step . For details, see the connecting device’s
owner's manual.
Note
LISTENING TO MUSIC FROM YOUR Bluetooth DEVICE
13
You can listen to the audio played back by this unit through Bluetooth-compatible wireless headphones. The audio will be
transmitted to the wireless headphones using “MusicCast CONTROLLER” installed on your mobile device.
Listening to music through wireless headphones
Set the
Bluetooth
connection for the
Bluetooth
device (wireless headphones, etc.) to standby.
Tap in the playback display of
“MusicCast CONTROLLER.”
Tap “Bluetooth Transmission.”
Select the Bluetooth device (wireless
headphones, etc.).
When the connection is established, the Bluetooth
indicator (☞ P.3) lights up.
Tap “Done.”
The sound is output by the receiving Bluetooth
device (wireless headphones, etc.).
•Use Bluetooth devices compatible with the A2DP profile.
• Audio from AirPlay or a Bluetooth device cannot be
transmitted to and output by another Bluetooth device.
y
• The playback sound is also output by the unit.
• The “MusicCast CONTROLLER” app displays shown here
are from an iPhone.
• For details on using your Bluetooth device, refer to its
owner’s manual.
WX-010
Bluetooth
speakers/headphones
Tap
Tap
Note
14
OTHER FUNCTIONS AND INFORMATION
You can use two WX-010 units to reproduce stereo sound by setting each speaker as the right
or left speaker.
Set the left and right speakers separately by following the steps below.
Connect each WX-010 to the same network by using the dedicated app “MusicCast
CONTROLLER.”
If the WX-010 is linked to another MusicCast unit, first disconnect the link by using the dedicated app “MusicCast
CONTROLLER.”
Tap (power)/CONNECT of each unit to set them to standby.
Tap and hold the following together for 3 seconds to set the left/right speakers.
1 For setting the left speaker: and
Indicators light from right to left repeatedly (refer to
of the table), and the unit enters pairing standby.
2
For setting the right speaker: and
Indicators light from left to right repeatedly (refer to
of the table), and the units start pairing.
Indicator display during the Stereo Pair
After paring is completed, the indicators light from the center to both sides (refer to of the table), and all indicators
return to the normal status.
Use the dedicated app “MusicCast CONTROLLER” to play back.
y
• You can check which speaker is the left or right speaker with the dedicated app “MusicCast CONTROLLER” (Indicators
light as
or of the table).
• In Stereo Pair mode, you can operate one speaker to simultaneously turn off both speakers or adjust the volume of both
speakers.
• If about five minutes passes while the unit cannot find the other speaker to connect to, the pairing standby will be cancelled
automatically.
• When in Stereo Pair mode, the option settings other than “Initialize the unit.” (☞ P.16) cannot be set.
The Stereo Pair setting remains even if the speakers enter standby or the power cable is unplugged and plugged again.
STEREO PAIR
• To use the Stereo Pair function, you need two
WX-010.
• Stereo Pair is available only when the Network
Standby of the unit is enabled (
☞
P.16).
Setting/Playing back music
WX-010
Left
speaker
WX-010
Right
speaker
Note
Stereo Pair
status
Indicator display
Start Pairing/
Checking the
Left and Right
Speaker
Pairing
Completed
Left speaker
Right speaker
Right-to-Left
Left-to-Right
Center to both sides
Note
STEREO PAIR
15
Tap (power)/CONNECT to set the left and right speakers to the standby.
Tap and hold (or ) and on either speaker together for 3 seconds.
Indicators light from both sides to the center and Stereo Pair will be canceled.
• The Stereo Pair can be canceled only during standby.
• If you cancel Stereo Pair with one of the two speakers, the other one will be canceled automatically.
• If one of the two speakers is disconnected from the network when canceling the Stereo Pair, cancel Stereo Pair on each
speaker.
Canceling Stereo Pair
Both sides to center
Indicator display
Note
Sidan laddas ...
Sidan laddas ...
Sidan laddas ...
Sidan laddas ...
Sidan laddas ...
Sidan laddas ...
Sidan laddas ...
Sidan laddas ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28

Yamaha Audio WX-010BL Användarmanual

WX-010BL
Yamaha Audio
varumärke
Yamaha Audio
Modell
WX-010BL
Kategori
Kompletterande musikutrustning
Typ
Användarmanual
Ladda ner pdf
Rapportera

på andra språk

Relaterade papper

Andra dokument