Yamaha RX-E100 Bruksanvisning

Kategori
CD-spelare
Typ
Bruksanvisning

Denna manual är också lämplig för

RL
RX-E100 / CDX-E100
OWNER’S MANUAL
MODE D’EMPLOI
BEDIENUNGSANLEITUNG
BRUKSANVISNING
MANUALE DI ISTRUZIONI
MANUAL DE INSTRUCCIONES
GEBRUIKSAANWIJZING
Natural Sound Stereo Receiver/Natural Sound Compact Disc Player
Récepteur Stéréo/Lecteur Compact Disque
BG
SUPPLIED ACCESSORIES After unpacking, check that the following parts are contained.
ACCESSOIRES FOURNIS Après le déballage, vérifier que les pièces suivantes sont incluses.
MITGELIEFERTES ZUBEHÖR
Nach dem Auspacken überprüfen, ob die folgenden Teile vorhanden sind.
MEDFÖLJANDE TILLBEHÖR Kontrollera efter det apparaten packats upp att följande delar finns med.
ACCESSORI IN DOTAZIONE
Verificare che tutte le parti seguenti siano contenute nell’imballaggio
dell’apparecchio.
ACCESORIOS INCLUIDOS Desembale el aparato y verificar que los siguientes accesorios están en la caja.
BIJGELEVERDE ACCESSOIRES
Controleer na het uitpakken of de volgende onderdelen voorhanden zijn.
Remote control
Télécommande
Fernbedienungseinheit
Fjärrkontrollen
Telecomando
Mando a distancia
Afstandbediening
AM loop antenna
Antenne cadre AM
MW-Rahmenantenne
AM ramantenn
Antenna AM ad uso interno
Antena de cuadro de AM
AM ringantenne
Indoor FM antenna
Antenne intérieure FM
UKW-Innenantenne
FM inomhusantenn
Antenna FM per interni
Antena interior de FM
FM binnenantenne
Batteries (size AAA, UM-4, R03)
Piles (format AAA, UM-4, R03)
Batterien (Größe AAA, UM-4, R03)
Batterier (Storl. AAA, UM-4, R03)
Batterie (size AAA, o UM-4, o R03)
Pilas (tamaño AAA, tipo UM-4, R03)
Batterijen (maat AAA, UM-4, R03)
<RX-E100>
<CDX-E100>
• System Control Cable
• Câble de commande du système
• Systemsteuerkabel
• Systemkontrollkabel
• Cavo di telecomando del sistema
• Cable de control del sistema
• Systeembedieningskabel
• RCA Pin Cable
• Câble de raccordement RCA
• RCA-Stiftkabel
• RCA stiftkabel
• Cavo con spinotti a spillo RCA
• Cable con clavijas RCA
• RCA (tulpstekker) kabel
SLEEP
A
D
C
E
B
TIME
RNDM
VOLUME
MODE
PTY SEEKFREQ PS/PTY/RT/CT
START
TAPE
AUX
MD CD
TUNER
PRESET
PTY SELECT
TAPE
MD REC
MODE START
TAPE REC
DISP
PROG
TAPE
REP
PEAK
DUBBING
E-1
English
INTRODUCTION
Thank you for purchasing this YAMAHA product. We hope it will give you many years of trouble-free enjoyment. For the
best performance, read this manual carefully. It will guide you in operating your YAMAHA product.
ENGLISH
FEATURES
<RX-E100>
Minimum RMS Output Power per Channel
40 W + 40 W (6, 20 - 20,000Hz, 0.1% THD)
Full Operation System Remote Control
40-Station FM/AM Preset Tuning
Multi-Function RDS Reception
SUBWOOFER Output Terminal
<CDX-E100>
S-bit DAC and 8fs Digital Filter
Optical Digital Output
Random, Repeat, and Program Play
CD TEXT Display
Peak Level Search
Tape Programming
The receiver (RX-E100) and CD player (CDX-E100) are the main units of the YAMAHA E100 series. You could upgrade
the system by adding the cassette deck (KX-E100) and MD recorder (MDX-E100)*.
* MD recorder (MDX-E100) may not be available for some areas.
PRECAUTIONS...................................................2
GETTING STARTED
The remote control ...............................................3
Connecting the speakers .......................................4
Connecting the system..........................................5
<RX-E100>
NAMES OF BUTTONS AND CONTROLS .......6
BASIC OPERATIONS
Listening to a source.............................................8
TUNER OPERATIONS
Listening to the radio............................................9
Presetting stations ............................................... 10
RECEIVING RDS STATIONS
Receiving RDS data ........................................... 11
PTY SEEK mode................................................12
Optional settings for RDS functions...................13
USING THE BUILT-IN TIMER
Setting the clock .................................................14
Adjusting the brightness of the display ..............14
Before using the timer ........................................15
Timer play and recording ...................................15
Sleep timer..........................................................16
<CDX-E100>
NAMES OF BUTTONS AND CONTROLS .....17
COMPACT DISC PLAYER OPERATIONS
CD playback .......................................................19
Selecting the time display and CD TEXT ..........20
Random-sequence play.......................................20
Repeat play .........................................................21
Program play ......................................................21
Peak level search ................................................22
ADD KX-E100 AND/OR MDX-E100 TO YOUR
SYSTEM
Operating the cassette deck, KX-E100 and MD
recorder, MDX-E100 with the remote control ...23
Before recording ................................................. 24
Dubbing setting ..................................................24
TAPE programming............................................25
ADDITIONAL INFORMATION
CD preventive care .............................................26
Troubleshooting..................................................26
Specifications .....................................................28
CONTENTS
E-2
IMPORTANT:
The wires in the mains lead are coloured in accordance
with the following code:
Blue: NEUTRAL
Brown: LIVE
As the colours of the wires in the mains lead of this
apparatus may not correspond with the coloured
markings identifying the terminals in your plug,
proceed as follows: The wire which is coloured BLUE
must be connected to the terminal which is marked
with the letter N or coloured BLACK. The wire which
is coloured BROWN must be connected to the terminal
which is marked with the letter L or coloured RED.
Making sure that neither core is connected to the earth
terminal of the three pin plug.
CAUTIONS
To assure the finest performance, please read this
manual carefully. Keep it in a safe place for future
reference.
Install your unit in a well ventilated, cool, dry, clean
place – away from windows, heat sources, vibration,
dust, moisture, or cold. To avoid humming sounds,
locate the unit away from other electrical appliances,
motors, and transformers. To prevent fire or electrical
shock, do not expose to rain and water.
(U.K. and Europe models only)
Be sure to allow at least 10 cm of ventilation space at
the top, on left, right, and back sides of RX-E100.
Do not operate the unit upside-down. It may overheat,
possibly causing damage.
Never open the cabinet. If something drops into the set,
contact your dealer.
Do not use force on switches, knobs or cords.
Always set the VOLUME control to minimum before
starting playback of an audio source: increase the
volume gradually to an appropriate level after play has
started.
When not planning to use this unit for long periods of
time (i.e., vacation, etc.), disconnect the AC power plug
from the wall outlet.
Grounding or polarization – Precautions should be taken
so that the grounding or polarization of the unit is not
defeated.
Do not clean the unit with chemical solvents; this might
damage the finish. Use a clean, dry cloth.
Be sure to read the “Troubleshooting” section on
common operating errors before concluding that your
unit is faulty.
Do not place another component on top of this unit, as
damage or discoloration on the surface of the unit may
result.
To prevent damage by lightning, disconnect the power
cord from the wall outlet during an electrical storm.
When disconnecting the power cord from the wall
outlet, grasp the plug; do not pull the cord.
Do not plug the AC power plug to the wall outlet before
you finish all connections.
The voltage to be used must be the same as that
specified on this unit. Using this unit with a higher
voltage than that which is specified is dangerous and
may result in a fire or other type of accident causing
damage. YAMAHA will not be held responsible for any
damage resulting from use of this unit with a voltage
other than that which is specified.
When listening to the receiver at a high volume level for
a long time, the temperature inside the unit rises. To
prevent overheating and possible damage to this unit,
the internal fan starts running.
Sudden temperature changes and storage or operation in
an extremely humid environment may cause
condensation inside the cabinet.
PRECAUTIONS: READ THIS BEFORE OPERATING THE UNIT
This compact disc player is
classified as a CLASS 1
LASER product.
The CLASS 1 LASER
PRODUCT label is located
on the rear exterior.
CLASS 1 LASER PRODUCT
Laser component in this product is capable of
emitting radiation exceeding the limit for Class 1.
CAUTION FOR CARRYING THE UNIT
Before carrying the unit, first remove all discs from
the unit, press STANDBY/ON to turn the unit off,
then disconnect the AC power plug from the wall
outlet.
CAUTION
Use of controls or adjustments or performance of
procedures other than those specified herein may
result in hazardous radiation exposure.
The unit is not disconnected from the AC power source
as long as it is connected to the wall outlet, even if this
unit itself is turned off. This state is called the standby
mode. In this state, this unit is designed to consume a
very small quantity of power.
For U.K. customers
If the socket outlets in the home are not suitable for the
plug supplied with this appliance, it should be cut off and
an appropriate 3 pin plug fitted. For details, refer to the
instructions described above.
Note: The plug severed from the mains lead must be
destroyed, as a plug with bared flexible cord is hazardous
if engaged in a live socket outlet.
SPECIAL INSTRUCTIONS FOR U.K. MODEL
E-3
English
STANDBY/ON PHONES
DISPLAY
+-+-
RL
MEMORY AUTO/MAN'L
TIME ADJ TIMER
HOUR MIN
BASS TREBLE BALANCE
MAXMIN
VOLUME
INPUT
PRESET/TUNINGPRESET/BAND
NATURAL SOUND STEREO RECEIVER RX-E100
30°
30°
Battery replacement
If you find that the remote control must be used closer to
the main unit than usual, the batteries are weak. Replace
batteries with new ones.
Remote control
sensor
The remote control
This remote control controls a whole system: not only
RX-E100 but also CDX-E100. Moreover, a cassette deck
(KX-E100) and MD recorder (MDX-E100) that level up
your system can be operated by it. Operating buttons for
each unit are explained on the pages below:
Receiver, RX-E100: p.7
CD player, CDX-E100: p.18
Cassette deck, KX-E100: p.23
MD recorder, MDX-E100: p.23
Loading the batteries for the remote control
1 Remove the battery compartment cover.
2 Insert 4 batteries into the battery compartment.
3 Replace the battery compartment cover.
Remote control operation range
Notes
There should be no large obstacles between the remote control
and the main unit.
If the remote control sensor is directly illuminated by strong
lighting (especially an inverter type of fluorescent lamp, etc.),
it might cause the remote control not to work correctly. In this
case, reposition the main unit to avoid direct lighting.
Within approximately
6 m (20 feet)
GETTING STARTED
Notes
Use only AAA, UM-4, R03 batteries for replacement.
Be sure the polarities are correct. (See the illustration inside
the battery compartment.)
Remove the batteries if the remote control will not be used for
an extended period of time.
If batteries leak, dispose of them immediately. Avoid touching
the leaked material or letting it come in contact with clothing,
etc. Clean the battery compartment thoroughly before
installing new batteries.
E-4
STEP
FREQUENCY
D
L
R
C
AB E
LR
L
R
SYSTEM
CONNETOR
SUBWOOFER
OUT
OUT IN IN
MD
CD
AUX
TAPE
6 MIN./SPEAKER
SPEAKERS
FM ANT GND AM ANT
75 UNBAL
Connecting the speakers
Never plug the AC power cord to the wall outlet until all connections are completed.
Follow the steps as shown below to connect the system using the supplied cords and accessories.
1 Connect the Speakers.
1 Unscrew the knob.
2 Remove approx. 5 mm (1/4”) of insulation from
each of the speaker wires and insert the bare wire
into the terminal.
3 Tighten the knob to secure the wire.
2 Connect the AM Antenna.
Set up the AM loop antenna, then connect it.
3 Connect the FM Antenna.
4 Connect the AC power cord to a wall outlet.
Use external FM/AM antennas if you need better reception.
Consult your dealer.
The AM loop antenna should be placed apart from the main
unit. The antenna may be hung on a wall.
To Connect the Subwoofer (optional)
You can reinforce the bass frequencies by adding a
subwoofer (optional).
Connect the SUBWOOFER OUT terminal of the unit to
the INPUT terminal of the subwoofer.
1
2
3
4
To wall outlet
FM antenna
AM loop antenna
Right speaker Left speaker
GETTING STARTED
Red: positive(+)
Black: negative(–)
1
2
3
GND AM ANT
FM ANT
75 UNBAL
E-5
English
L
R
SYSTEM
CONNECTOR
DIGITAL
OPTICAL
ANALOG
OUT
OUT
STEP
FREQUENCY
D
L
R
C
AB E
E
LR
L
R
SYSTEM
CONNETOR
SUBWOOFER
OUT
OUT IN IN
MD
CD
AUX
TAPE
6 MIN./SPEAKER
SPEAKERS
FM ANT GND AM ANT
75 UNBAL
Adding KX-E100 and MDX-E100 to the above system (For details, refer to the owner's manual
supplied with the respective component.)
1 Connect Å and ı of RX-E100 to Å and ı of KX-E100.
2 Connect Ç and Î of RX-E100 to Ç and Î of MDX-E100.
3 Connect an external component to the AUX terminal of RX-E100.
4 Connect DIGITAL OPTICAL OUT of CDX-E100 to DIGITAL OPTICAL IN of MDX-E100.
Take off the covers of the optical fiber cable plug, the DIGITAL OPTICAL OUT jack, and the DIGITAL OPTICAL
IN jack before making digital connections. Be sure to replace the terminal’s cover when the terminal on the rear panel
is not being used, in order to protect from dust.
5 AC OUTLET (CDX-E100)
Connect the AC power plug of MDX-E100 or KX-E100 (Except for the UK model).
Connecting the system
GETTING STARTED
Connecting RX-E100 and CDX-E100
1 Connect to using the RCA pin cable.
Insert the plugs into the jacks of the same colour.
2 Connect RX-E100 and CDX-E100 with the system control cable.
The other SYSTEM CONNECTOR of CDX-E100 is for connecting MDX-E100 or KX-E100.
3 Connect the AC power plug of CDX-E100 to AC OUTLET of RX-E100.
To wall outlet
To RX-E100
System control cable
RCA pin cable
1
2
3
<RX-E100>
<CDX-E100>
E-6
Display
# RDS indicator (P.11)
RDS mode indicators (P.11)
$ PTY HOLD indicator (P.12)
TIMER indicator (P.15)
% SLEEP indicator (P.16)
Front panel
~ STANDBY/ON (P.8)
Ÿ PHONES (P.8)
! DISPLAY (P.14)
MEMORY/TIME ADJ (P.10/P.14)
@ AUTO/MAN’L/TIMER (P.9/P.15)
¤ BASS (P.8)
# TREBLE (P.8)
BALANCE (P.8)
$ INPUT (P.8)
~ Multi-information display
Ÿ PRESET indicator (P.10)
! STEREO indicator (P.9)
TUNED indicator (P.9)
@ AUTO indicator (P.9)
¤ MEMORY indicator (P.10)
RX-E100 NAMES OF BUTTONS AND CONTROLS
VOLUME (P.8)
% PRESET/TUNING / PTY SELECT
(P.9/P.12)
HOUR/MIN (P.14)
PRESET/BAND (P.9)
^ Display (P.6)
Remote Control Sensor (P.3)
& TIMER indicator (P.15)
STANDBY indicator (P.8)
STEREO AUTO RDS PS PTY RT CT TIMER
SLEEPTUNED MEMORY PTY HOLD
PRESET
STANDBY/ON PHONES
DISPLAY
+-+-
RL
MEMORY AUTO/MAN'L
TIME ADJ TIMER
HOUR PTY SELECT MIN
BASS TREBLE BALANCE
MAXMIN
VOLUME
INPUT
PRESET/TUNINGPRESET/BAND
NATURAL SOUND STEREO RECEIVER RX-E100
STANDBY
TIMER
E-7
English
Remote control
~ SLEEP (P.16)
Ÿ DISP (Display) (P.13)
! A/B/C/D/E (P.10)
POWER (P.8)
@ Preset numbers (P.10)
¤ FREQ PS/PTY/RT/CT (P.11)
# PTY SEEK MODE (P.12/P.13)
PTY SEEK START (P.12/P.13)
$ VOLUME + – (P.8)
TAPE (KX-E100) (P.23)
% MD (MDX-E100) (P.23)
AUX (The equipment connected to the AUX
terminal) (P.5)
^ CD (CDX-E100) (P.19)
TUNER (RX-E100) (P.10)
& PRESET/PTY SELECT / (P.10/P.12)
Note
~ are operation buttons and input selectors for each
component.
RX-E100 NAMES OF BUTTONS AND CONTROLS
A
D
C
E
B
TIME
RNDM
VOLUME
MODE
PTY SEEKFREQ PS/PTY/RT/CT
START
TAPE
AUX
MD CD
TUNER
PRESET
PTY SELECT
TAPE
MD REC
MODE START
TAPE REC
PROG
TAPE
REP
PEAK
DUBBING
SLEEP DISP
E-8
RX-E100 BASIC OPERATIONS
Listening to a source
4 Play the source. (Refer to the owner’s manual
supplied with each selected component.)
5 Adjust the volume level by turning VOLUME on the
front panel or pressing VOLUME + on the remote
control.
6 If desired, adjust BASS, TREBLE, and BALANCE.
BASS: Turn this control clockwise to increase (or
counterclockwise to decrease) the low frequency
response.
TREBLE: Turn this control clockwise to increase (or
counterclockwise to decrease) the high frequency
response.
BALANCE: Adjust the balance of the output volume
from the left and right speakers to compensate for
sound imbalance caused by the speaker location or
listening room conditions
These controls are only effective for the sound from the main
speakers.
When you use headphones
Connect the headphones to the PHONES jack. You can
listen to the sound from the main speakers through the
headphones.
When you have finished using this
unit
Press STANDBY/ON on the front panel again or
POWER on the remote control to set this unit to the
standby mode.
The STANDBY indicator lights up.
Auto power off function
RX-E100 will be put automatically into the standby mode
under the following conditions:
The component connected to RX-E100 is in stop mode
and not operated for 30 minutes.
TUNER or AUX is not selected as an input source.
STANDBY/ON PHONES
DISPLAY
+-+-
RL
MEMORY AUTO/MAN'L
TIME ADJ TIMER
HOUR PTY SELECT MIN
BASS TREBLE BALANCE
MAXMIN
VOLUME
INPUT
PRESET/TUNINGPRESET/BAND
NATURAL SOUND STEREO RECEIVER RX-E100
TIMER
STANTBY
VOLUME
STANDBY/ON INPUTBALANCE
TREBLE
BASS
PHONES
A
D
C
E
B
TIME
RNDM
VOLUME
MODE
PTY SEEKFREQ PS/PTY/RT/CT
START
TAPE
AUX
MD CD
TUNER
PRESET
PTY SELECT
TAPE
MD REC
MODE START
TAPE REC
PROG
TAPE
REP
PEAK
DUBBING
SLEEP DISP
POWER
VOLUME –/+
1 Set the volume to “MIN” by turning VOLUME.
2 Turn on the power by pressing STANDBY/ON on
the front panel, or POWER on the remote control.
RX-E100 can be used to turn on or put in standby mode
the system connected E100 series components depending
on their prior standby/on status.
3 Select the desired input source by turning INPUT so
that the source appears on the display.
When you operate the component connected to the AUX
terminal, turn INPUT to select AUX.
E-9
English
TUNER OPERATIONS
Automatic tuning
1 Select TUNER by turning INPUT so that the
frequency of a radio station appears in the display.
2 Press PRESET/BAND to select the reception band.
Do not select the preset tuning mode (in which
“PRESET” appears on the display).
3 Press AUTO/MAN’L so that “AUTO” appears in the
display.
4 Press PRESET/ TUNING (For a higher
frequency) or
(For a lower frequency).
5 The unit starts searching for a station.
When the unit finds a station, the unit stops searching
and “TUNED” appears on the display.
6 If the located station is not the one you want, repeat
steps 4 and 5 until a station you want is tuned.
Notes
If automatic tuning search does not find the desired station, try
manual tuning as described next.
When an FM stereo broadcast with sufficient signal strength is
received, “STEREO” appears on the display and you can listen
to stereo sound.
Listening to the radio
Manual tuning
1 Follow steps 1 and 2 described in “Automatic
tuning.”
2 Press AUTO/MAN’L so that “AUTO” disappears
from the display.
3 Press TUNING (For a higher frequency) or
(For a lower frequency) to select your desired station.
Each time you press TUNING or , the frequency
changes step by step.
You can find radio stations automatically and manually.
STEREO AUTO
TUNED
STANDBY/ON PHONES
DISPLAY
+-+-RL
MEMORY AUTO/MAN'L
TIME ADJ TIMER
HOUR PTY SELECT MIN
BASS TREBLE BALANCE
MAXMIN
VOLUME
INPUT
PRESET/TUNINGPRESET/BAND
NATURAL SOUND STEREO RECEIVER RX-E100
PRESET/TUNING /
INPUT
AUTO/MAN’L
PRESET/BAND
E-10
TUNER OPERATIONS
To preset stations manually
1 Tune in a desired station.
(Refer to the previous page for the tuning procedure.)
2 Press MEMORY.
3 Within about 5 seconds, use PRESET/TUNING
/ to select a desired preset number. Continue
pressing PRESET/TUNING
/ to select the
group of the preset stations (A, B, C, D, and E).
4 Press MEMORY.
•“MEMORY”, “PRESET”, and preset number will appear
on the display.
STEREO
TUNED
MEMORY
PRESET
STEREO
TUNED
MEMORY
PRESET
Presetting stations
The unit can preset station frequencies selected by
Automatic tuning or Manual tuning. Up to 40 stations can
be stored. With this function, you can select any desired
station by pressing the corresponding preset station
number.
5 Repeat steps 1 to 4 until all desired stations are
preset.
Notes
A new setting can be preset in place of a previous one.
The preset stations are retained for a week after you disconnect
the AC power cord or a power failure occurs.
To preset stations automatically
1 Select TUNER as input source by turning INPUT.
2 Press MEMORY for about 2 seconds.
The unit starts presetting stations, “AUTO” and
“MEMORY” will flash on the display.
Received stations are stored to A1, A2...A8 sequentially.
After 40 stations or all FM and AM stations are stored, the
display will show the preset station A1.
To recall a preset station
Press TUNER and select the desired number by pressing
PRESET/BAND and PRESET/TUNING / on the
front panel or PRESET
/ , A/B/C/D/E and 1-8 on
the remote control.
The arrow will appear for a second when
it is preset.
STANDBY/ON PHONES
DISPLAY
+-+-
RL
MEMORY AUTO/MAN'L
TIME ADJ TIMER
HOUR MIN
BASS TREBLE BALANCE
MAXMIN
VOLUME
INPUT
PRESET/TUNINGPRESET/BAND
NATURAL SOUND STEREO RECEIVER RX-E100
PTY SELECT
PRESET/TUNING /
INPUTPRESET/BANDMEMORY
A
D
C
E
B
TIME
RNDM
VOLUME
MODE
PTY SEEKFREQ PS/PTY/RT/CT
START
TAPE
AUX
MD CD
TUNER
PRESET
PTY SELECT
TAPE
MD REC
MODE START
TAPE REC
PROG
TAPE
REP
PEAK
DUBBING
SLEEP DISP
1~8
A/B/C/D/E
TUNER
PRESET
E-11
English
Playing CDsGetting Started
RECEIVING RDS STATIONS
PS
The name of the RDS station being received is displayed.
If the unit cannot find a station with PS data, the unit stops
searching and “NO PS” appears on the display.
PTY
The type of the program on the RDS station now being
received is displayed. You can make this unit search for a
station which is broadcasting a program of a desired
program type. (Refer to PTY program mode in the next
section for details.)
RT
Information about the program (such as the title of the
track, artist name, etc.) on the RDS station being received
is displayed using a maximum of 64 alphabetical
characters, including umlaut sign. If other characters are
used in the RT data, they are displayed with an under-bar.
If the unit cannot find a station with RT data, the unit stops
searching and “NO RT” appears on the display.
CT
Current time is displayed.
If the unit cannot find a station with CT data, the unit stops
searching and “NO CT” appears on the display.
Note
RDS may not work properly if the station you are tuned to is
not transmitting the RDS signal properly or if the signal
strength is weak.
Some FM stations do not offer RDS service. Of those that do,
not all provide the same types of services. The types provided
by the received RDS station are dimmed on the display. Check
with your local radio stations for details on RDS services in
your area.
RDS (Radio Data System) is a data transmission system
which has been introduced by FM stations in many
European countries. Stations using this system transmit an
inaudible stream of data in addition to the normal radio
signal. RDS data contains various types of information,
such as PS (Program Service), PTY (Program Type), RT
(Radio Text), and CT (Clock Time).
Receiving RDS data
1 Tune in the FM station. (Refer to page 9, or you can
simply press TUNER on the remote control.)
2 Press FREQ PS/PTY/RT/CT to choose the mode.
Each time you press FREQ PS/PTY/RT/CT, the
type changes as follows:
A
D
C
E
B
TIME
RNDM
VOLUME
MODE
PTY SEEKFREQ PS/PTY/RT/CT
START
TAPE
AUX
MD CD
TUNER
PRESET
PTY SELECT
TAPE
MD REC
MODE START
TAPE REC
PROG
TAPE
REP
PEAK
DUBBING
SLEEP DISP
FREQ PS/
PTY/RT/CT
TUNER
RDS PS PTY RT CT
RDS PS PTY RT CT
RDS PS PTY RT CT
RDS PS PTY RT CT
E-12
RECEIVING RDS STATIONS
You can locate a desired station by selecting a program
type. The unit searches all preset stations into the type of
programs currently being broadcast from the RDS
stations.
NEWS
News
AFFAIRS
Current Affairs
INFO
General Information
SPORT
Sports
EDUCATE
Education
DRAMA
Drama
CULTURE
Culture
SCIENCE
Science
VARIED
Light Entertainment
POP M
Pops
ROCK M
Rock
M.O.R. M
Middle of the Road
Music (Easy-listening)
LIGHT M
Light Classics
CLASSICS
Serious Classics
OTHER M
Other Music
PTY SEEK mode
To locate a station
1 Tune in the FM station. (Refer to page 9, or you can
simply press TUNER on the remote control.)
2 Press PTY SEEK MODE once so that “PTY” and a
PTY program flashes on the display.
3 Within about 20 seconds, press PTY SELECT
(for a higher frequency) or (for a lower
frequency) until the desired program type appears on
the display.
4 Within about 20 seconds, press PTY SEEK START.
If a station broadcasting the selected program type is
found, the unit stops searching and the Program Service
name appears on the display.
“PTY HOLD” appears on the display.
5 Repeat step 4 until the desired station is located.
If there is no station broadcasting the program type
you select, “NO PTY” appears on the display, then
the Program Service name or frequency appears on
the display.
List of PTY (Program Type)
A
D
C
E
B
TIME
RNDM
VOLUME
MODE
PTY SEEKFREQ PS/PTY/RT/CT
START
TAPE
AUX
MD CD
TUNER
PRESET
PTY SELECT
TAPE
MD REC
MODE START
TAPE REC
PROG
TAPE
REP
PEAK
DUBBING
SLEEP DISP
PTY SEEK MODE
PTY SEEK START
PTY
RDS PTY
PTY HOLD
PRESET
PTY SELECT /
E-13
English
Playing CDsGetting Started
RECEIVING RDS STATIONS
The tuner has the following functions which make use of
the RDS data service. These are originally in operation
ON. However, you can turn these functions OFF, if so
desired.
Optional settings for
RDS functions
defs
1 Select the FM band by pressing TUNER.
2 Press DISP to display the current time.
3 Press FREQ PS/PTY/RT/CT.
4 Each time you press PTY SEEK MODE the display
will change as follows:
1. CT = CLOCK (ON/OFF)
The tuner corrects the time of the built-in clock
automatically by synchronizing it with the CT data
on the RDS station being received.
If you receive an RDS station of some other country, the
built-in clock is synchronized with the time setting of the
country.
If the built-in clock is not yet set for the current time or
reset due to a power failure, etc., it will be set for the time
of the CT data automatically, whether this setting is ON
or OFF.
2. LOCAL = CT (ON/OFF)
If the RDS station being received employs the
local time (summer time, etc.) data service, its time
is displayed in the CT mode.
3. A.M. = RDS (ON/OFF)
RDS stations are searched instead of all FM
stations by the automatic preset tuning operation
when the setting is ON. (Refer to page 10.)
4. RT SPEED: ±0
Changes the scrolling speed of the radio text
decreasing the value and, in turn, reducing the
speed.
Control Range: ±0 to ±3 (Preset value: ±0)
5 Choose the function ON or OFF by pressing PTY
SEEK START, confirming it in the display.
Press PTY SEEK START repeatedly to change the
value for RT SPEED.
If there is no operation for about 20 seconds, this mode is
cancelled and turns into the frequency display. If the
station has PS data, it turns into the PS mode.
6 Press FREQ PS/PTY/RT/CT again to restore the
frequency display mode.
DISP
A
D
C
E
B
TIME
RNDM
VOLUME
MODE
PTY SEEKFREQ PS/PTY/RT/CT
START
TAPE
AUX
MD CD
TUNER
PRESET
PTY SELECT
TAPE
MD REC
MODE START
TAPE REC
PROG
TAPE
REP
PEAK
DUBBING
SLEEP DISP
PTY SEEK MODE
PTY SEEK START
FREQ PS/
PTY/RT/CT
TUNER
E-14
USING THE BUILT-IN TIMER
Setting the clock
1 While the power is on, press DISPLAY to display
the time.
2 While holding TIME ADJ, press HOUR to set the
hour.
If you want to move the time in the reverse direction,
press HOUR while holding TIME ADJ and PRESET/
BAND.
3 While holding TIME ADJ, press MIN to set the
minutes.
If you want to move the time in the reverse direction,
press MIN while holding TIME ADJ and PRESET/
BAND.
To display the clock
Press DISPLAY.
The current time appears for about 8 seconds, then the
normal display returns.
Note
In the event of a power failure or when the AC power cord is
disconnected for more than five minutes, you must reset the
clock.
You must set the clock before you use the timer functions.
The clock is based on a 24-hour system.
Adjusting the brightness
of the display
You can adjust the brightness of the display. If you have
connected the CD player (CDX-E100), cassette deck
(KX-E100), and/or MD recorder (MDX-E100) to this
unit, the brightness of the displays is automatically
adjusted to that of this unit.
Press and hold DISPLAY for about two seconds so that
“Dimmer ±0” appears on the display. While holding
DISPLAY, turn INPUT clockwise to increase or
counterclockwise to decrease brightness.
Control Range: ±0 to –6 (Preset value: ±0)
STANDBY/ON PHONES
DISPLAY
+-+-
RL
MEMORY AUTO/MAN'L
TIME ADJ TIMER
HOUR PTY SELECT MIN
BASS TREBLE BALANCE
MAXMIN
VOLUME
INPUT
PRESET/TUNINGPRESET/BAND
NATURAL SOUND STEREO RECEIVER RX-E100
HOURDISPLAY
PRESET/BANDTIME ADJ
MIN
STANDBY/ON PHONES
DISPLAY
+-+-
RL
MEMORY AUTO/MAN'L
TIME ADJ TIMER
HOUR PTY SELECT MIN
BASS TREBLE BALANCE
MAXMIN
VOLUME
INPUT
PRESET/TUNINGPRESET/BAND
NATURAL SOUND STEREO RECEIVER RX-E100
INPUT
DISPLAY
E-15
English
USING THE BUILT-IN TIMER
Timer play and recording
By using the built-in timer, you can have the unit turn on
at a specified time and begin playing or recording
automatically. You can also specify the turn off time.
3. Timer REC
Select the recording component by turning INPUT.
If you like to enjoy timer play with TUNER or
AUX, select “REC Mode OFF”.
4. ON Time
“ON Time” appears on the display for a second,
and changed to the time setting mode.
Press HOUR to set the hour.
Press MIN to set the minute.
5. OFF Time
Set the time the same way as above.
If you set the ON time but not OFF time, the timer
play or recording will finish automatically after an
hour.
Notes
The display mode will change in about 8 seconds. If the
mode is changed before the setting is completed, call the
mode again by pressing DISPLAY once or more.
If you select the input other than TUNER and AUX on
“2. Timer Input”, “3. Timer REC” is skipped.
2 Press TIMER to complete the timer setting.
The system is put in the standby mode.
The STANDBY and TIMER indicators light up.
If you continue using the system, press STANDBY/
ON to turn on this unit.
To cancel the timer play setting
Press DISPLAY to show the current time, then press
TIMER so that “TIMER” goes off from the display. You
can also cancel by pressing TIMER in standby mode.
Note
In the event of a power failure or when the AC power cord is
disconnected for more than five minutes, you must reset the
clock.
1 Press DISPLAY.
Whenever DISPLAY is pressed, the display mode
changes as follows:
1. Clock Time (TIMER on/off mode)
If you have not set the clock yet “Set Clock”
appears. You need to set the current time as
described on page 14.
2. Timer Input
Select the source to be played by turning INPUT.
Timer recording is possible only when you select
TUNER or AUX.
STANDBY/ON PHONES
DISPLAY
+-+-RL
MEMORY AUTO/MAN'L
TIME ADJ TIMER
HOUR PTY SELECT MIN
BASS TREBLE BALANCE
MAXMIN
VOLUME
INPUT
PRESET/TUNINGPRESET/BAND
NATURAL SOUND STEREO RECEIVER RX-E100
MIN
INPUT
DISPLAY
HOURTIMER
Before using the timer
If you want to use the cassette deck, KX-E100 or the MD
Recorder, MDX-E100 for timer play or recording, you
must first make the connections as shown in “Connecting
the system” on page 5. For details, refer to the instructions
supplied with the MDX-E100 or KX-E100.
(Example)
E-16
USING THE BUILT-IN TIMER
Sleep timer
The unit can be turned off automatically at a selected
SLEEP time.
1 Play the desired sound source.
2 Press SLEEP repeatedly until the desired sleep time
appears in the display.
Each time you press SLEEP, the sleep time changes
as follows:
SLEEP
A
D
C
E
B
TIME
RNDM
DISP
PROG
TAPE
REP
PEAK
SLEEP
SLEEP 2h00m
SLEEP 1h30m
SLEEP 1h00m
SLEEP 0h30m
SLEEP OFF
About 4 seconds after setting, the normal display will
resume.
“SLEEP” will appear in the display.
3 The unit will turn off automatically when the selected
sleep time is reached.
E-17
English
CDX-E100 NAMES OF BUTTONS AND CONTROLS
Display
¤ RANDOM indicator (P.20)
# PROGRAM indicator (P.21)
REPEAT S/F (Single or Full) indicator (P.21)
$ CD-TEXT indicator (P.20)
Front panel
~ STANDBY/ON (P.19)
Ÿ Display (this page)
! $/! (Skip/Search Backward)
/ (Skip/Search Forward) (P.19)
~ Multi-information Display
Ÿ * Pause indicator
! # Play indicator
A B Tape side indicator (P.25)
@ Music calendar
REPEAT
PROGRAM
TITLE ARTIST TRACK CD-TEXT
ABRANDOM
123456789
10
11 12 13 14 15 16 17 18 19 20
SF
NATURAL SOUND COMPACT DISC PLAYER CDX-E100
STANDBY/ON
^ (Play/Pause) (P.19)
@ & (Stop) (P.19)
¤ (Open/Close) (P.19)
# Disc Tray (P.19)
E-18
CDX-E100 NAMES OF BUTTONS AND CONTROLS
Remote control
SLEEP
A
D
C
E
B
TIME
RNDM
VOLUME
MODE
PTY SEEKFREQ PS/PTY/RT/CT
START
TAPE
AUX
MD CD
TUNER
PRESET
PTY SELECT
TAPE
MD REC
MODE START
TAPE REC
DISP
PROG
TAPE
REP
PEAK
DUBBING
~ TIME (P.20)
Ÿ REP (Repeat) (P.21)
! PROG (Program) (P.21)
RNDM (Random) (P.20)
@ PEAK (Peak Search) (P.22)
¤ TAPE (P.25)
# POWER (P.19)
Numeric buttons (P.19)
$ CD input (P.19)
$/! (Skip/Seach Backward) (P.19)
% / (Skip/Seach Forward) (P.19)
^ (Play/Pause) (P.19)
^ & (Stop) (P.19)
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31

Yamaha RX-E100 Bruksanvisning

Kategori
CD-spelare
Typ
Bruksanvisning
Denna manual är också lämplig för