Yamaha KX-E100 Bruksanvisning

varumärke: Yamaha

Modell: KX-E100

Kategori: Kassettspelare

Typ: Bruksanvisning

KX-E100

Natural Sound Stereo Cassette Deck

Platine Cassette Stéréo

OWNER’S MANUAL

MODE D’EMPLOI

BEDIENUNGSANLEITUNG

BRUKSANVISNING

MANUALE DI ISTRUZIONI

MANUAL DE INSTRUCCIONES

GEBRUIKSAANWIJZING

E-2

Dolby noise reduction is extremely effective in reducing undesirable background hiss on tapes. This unit incorporates

Dolby B/C type noise reduction systems. The conventional Dolby B-type noise reduction provides approximately 8 dB

improvement in S/N ratio and C-type adds additional improvement over the B-type. The noise reduction is applied to both

recording and playback; be sure that the same noise reduction is used on recording and playback. Pressing DOLBY NR

switches between Dolby B, C and OFF.

Dolby noise reduction manufactured under license from Dolby Laboratories Licensing Corporation.

“DOLBY” and the double-D symbol

are trademarks of Dolby Laboratories Licensing Corporation.

INTRODUCTION

Thank you for purchasing this YAMAHA product. We hope it will give you many years of trouble-free enjoyment. For the

best performance, read this manual carefully. It will guide you in operating your YAMAHA product.

ENGLISH

FEATURES

• High Performance Auto-Reverse Tape Deck

• Dolby B/C Type Noise Reduction

• Applicable to Metal Tape Recording

CONTENTS

PRECAUTIONS .................................................. 3

NAMES OF CONTROLS AND FUNCTIONS

Front panel............................................................ 4

Display ................................................................. 4

GETTING STARTED

Connecting the unit to the receiver RX-E100 and

CD player CDX-E100 .......................................... 5

SUPPLIED ACCESSORIES

This unit, KX-E100 is one of the YAMAHA E100 series components.

• RCA Pin Cable x2 • System Control Cable x1

OPERATIONS

Playback ............................................................... 6

Recording ............................................................. 7

ADDITIONAL INFORMATION

Troubleshooting.................................................... 8

Notes about cassette tapes .................................... 9

Specifications ....................................................... 9

• Synchronized Recording

• Automatic Dubbing Function

Dolby B/C Type Noise Reduction

• REC/PLAY Level Meters with Peak Hold Function

E-3

English

PRECAUTIONS: READ THIS BEFORE OPERATING THE UNIT

CAUTIONS

•

To assure the finest performance, please read this manual

carefully. Keep it in a safe place for future reference.

• Install your unit in a well ventilated, cool, dry, clean

place – away from windows, heat sources, vibration,

dust, moisture, or cold. To avoid humming sounds,

locate the unit away from other electrical appliances,

motors, and transformers. To prevent fire or

electrical shock, do not expose to rain and water.

• Do not operate the unit upside-down. It may

overheat, possibly causing damage.

• Never open the cabinet. If something drops into the

set, contact your dealer.

• Do not use force on switches, knobs or cords.

• When not planning to use this unit for long periods

of time (i.e., vacation, etc.), disconnect the AC power

plug from the wall outlet.

• Grounding or polarization – Precautions should be

taken so that the grounding or polarization of the unit

is not defeated.

• Do not clean the unit with chemical solvents; this

might damage the finish. Use a clean, dry cloth.

• Be sure to read the “Troubleshooting” section on

common operating errors before concluding that

your unit is faulty.

• Do not place another component on top of this unit,

as damage or discoloration on the surface of the unit

may result.

•

To prevent damage by lightning, disconnect the power

cord from the wall outlet during an electrical storm.

• When disconnecting the power cord from the wall

outlet, grasp the plug; do not pull the cord.

• Do not plug the AC power cord to the wall outlet

before you finish all connections.

• The voltage to be used must be the same as that

specified on this unit. Using this unit with a higher

voltage than that which is specified is dangerous and

may result in a fire or other type of accident causing

damage. YAMAHA will not be held responsible for

any damage resulting from use of this unit with a

voltage other than that which is specified.

• Never allow metallic items (e. g. screwdrivers, tools,

etc.) to come near the record/playback head

assembly. Doing so may not only scratch or damage

the head’s mirror-smooth finish, but also change the

magnetic characteristics of the heads, causing a

deterioration in reproduction quality.

• Although the record/playback head used in this unit

is a high quality head with outstanding reproduction

characteristics, it can become dirty through the use of

old tapes or from dust accumulation over time.

This can have a serious effect on reproduction

quality.

Clean the heads regularly with one of the commonly

available head cleaners or with an appropriate

cleaning solution.

NOTE

Please check the copyright laws in your country to

record from records, compact discs, radio, etc.

Recording of copyright material may infringe

This unit is not disconnected from the AC power

source as long as it is connected to the wall outlet,

even if this unit itself is turned off. This state is

called the standby mode. In this state, this unit is

designed to consume a very small quantity of power.

IMPORTANT:

The wires in the mains lead are coloured in accordance

with the following code:

Blue: NEUTRAL

Brown: LIVE

As the colours of the wires in the mains lead of this

apparatus may not correspond with the coloured

markings identifying the terminals in your plug,

proceed as follows: The wire which is coloured BLUE

must be connected to the terminal which is marked

with the letter N or coloured BLACK. The wire which

is coloured BROWN must be connected to the terminal

which is marked with the letter L or coloured RED.

Making sure that neither core is connected to the earth

terminal of the three pin plug.

For U.K. customers

If the socket outlets in the home are not suitable for the

plug supplied with this appliance, it should be cut off and

an appropriate 3 pin plug fitted. For details, refer to the

instructions described above.

SPECIAL INSTRUCTIONS FOR U.K. MODEL

Note: The plug severed from the mains lead must be

destroyed, as a plug with bared flexible cord is hazardous

if engaged in a live socket outlet.

E-4

NAMES OF CONTROLS AND FUNCTIONS

Front panel

~ STANDBY/ON (p.6)

Ÿ COUNTER RESET (p.7)

! MODE (p.6)

⁄ Multi-information display (p.4)

@ REC/PAUSE (p.7)

¤ DOLBY NR (p.2)

# REC LEVEL (p.7)

‹ ! / ⁄ (Rewind, Music search backward/

Fast-forward, Music search forward) (p.6)

$ DIRECTION @# (p.6)

› # (Play) (p.6)

% & (Stop) (p.6)

ﬁ (Open/Close) (p.6)

^ Tape tray (p.6)

Display

~ Counter display

Ÿ Reverse mode indicator

! Dolby Noise Reduction indicator

⁄ Direction indicator

@ REC indicator

-30 20 15 10 8 6 4 2 0 2 4 6 +db

B C REC PLAY

MAX

MIN

REC LEVEL

DOLBY NR

MODE

COUNTER

RESET

DIRECTION

NATURAL SOUND STEREO CASSETTE DECK KX-E100

STANDBY/ON

REC/

PAUSE

DOLBY B-C NR

¤ Music SEARCH indicator

# PLAY indicator

‹ Rewind/Fast-forward indicator

$ REC/PLAY level indicator

E-5

English

SYSTEM

CONNECTOR

DIGITAL

OPTICAL

ANALOG

OUT

STEP

FREQUENCY

AB E

SUBWOOFER

OUT

OUT IN IN

AUX

TAPE

6 Ω MIN./SPEAKER

SPEAKERS

FM ANT GND AM ANT

75 Ω UNBAL

SYSTEM

CONNECTOR

OUTIN

SYSTEM

CONNECTOR

Connecting the unit to the receiver RX-E100 and

CD player CDX-E100

Never plug the AC power cord into the wall outlet until all other connections are completed.

Follow the steps as shown below to connect the unit to the receiver (RX-E100), CD player (CDX-E100), and MD recorder

(MDX-E100) using the supplied accessories.

1 Connect Å to Å, and ı to ı using the RCA pin cables.

Insert the plugs into the jacks of the same colour.

• The two RCA pin cables are the same, so you can connect Å or ı using either cord.

2 Connect the unit and the CDX-E100 (or MDX-E100) with the system control cable.

3 Connect the AC power cord to AC OUTLET of CDX-E100 (or MDX-E100) (except for U.K. model).

GETTING STARTED

To wall outlet

To RX-E100

To CDX-E100

System control cable

RCA pin cables

<CDX-E100>

<KX-E100>

<RX-E100>

E-6

OPERATIONS

1 Press STANDBY/ON to turn on this unit and also

RX-E100.

2 Set RX-E100 to cassette deck function mode.

3 Press to open the tape tray and place a recorded

tape on the tray.

4 Press to close the tape tray.

5 Press MODE to select the reverse mode.

Each time you press MODE, the reverse mode

changes and the corresponding mode indicator lights

up as follows:

: One side of the tape is played back.

: Both sides of the tape are played back.

: Both sides of the tape are played back up to 8

times continuously.

Playback

You can use any type of tape, since the unit automatically

detects the tape type.

6 Press DIRECTION to change the direction of the

tape.

• If you place the tape on the tray with side A

upward, # indicates playing side A and @

indicates playing side B.

7 Select the noise reduction type using DOLBY NR if

necessary.

8 Press # to start play.

To stop play

Press &.

To eject a tape

Press to open the tape tray and remove the tape from

the tray.

To adjust the volume level

Use the volume control of RX-E100.

To fast-forward or rewind the tape

Press ⁄ or ! to fast-forward or rewind the tape

during stop mode.

To search for the beginning of a

selection

Press ⁄ or ! to search for the beginning of the next

or current selection during play mode.

Notes

• The blank interval between selections must be at least 4

seconds long.

• The search function may not operate properly with tapes

recorded at a low recording level or which have excessive

noise.

• When you play the beginning part or end part of the tape, the

search function may not work correctly.

Tape Tray

! / ⁄ DIRECTIONMODESTANDBY/

MAX

MIN

REC LEVEL

DOLBY NR

REC/

PAUSE

MODE

COUNTER

RESET

DIRECTION

NATURAL SOUND STEREO CASSETTE DECK KX-E100

STANDBY/ON

DOLBY B-C NR

DOLBY NR

E-7

English

OPERATIONS

1 Set the recording mode of RX-E100 and other

components.

2 Press MODE to select the reverse mode.

Each time you press MODE, the reverse mode

changes and the corresponding mode indicator lights

up as follows:

: One side of the tape is recorded.

: Both sides of the tape are recorded.

3 Press DIRECTION to change the direction of the

tape.

• If you place the tape on the tray with side A

upward, # indicates recording side A and @

indicates recording side B.

4 Press REC/PAUSE.

The unit turns into standby mode for recording and

the REC indicator flashes.

5 Adjust the recording level by turning REC LEVEL.

For the best results, play the loudest passage of the

source to be recorded and watch the recording level

meter in the display. Adjust REC LEVEL so that the

highest peak causes the +2 dB level indicators to

flicker.

When recording a CD, use Peak Level Search on

CDX-E100 for the optimum adjustment.

6 Select the noise reduction type using DOLBY NR if

necessary.

7 Press #.

MAX

MIN

REC LEVEL

DOLBY NR

REC/

PAUSE

MODE

COUNTER

RESET

DIRECTION

NATURAL SOUND STEREO CASSETTE DECK KX-E100

STANDBY/ON

DOLBY B-C NR

8 Start playing the source component.

• Synchronized start is possible if you have

connected the CD player, CDX-E100 or MD

recorder, MDX-E100 to this unit. Press ^ on

MDX-E100 or CDX-E100 after step 6. Recording

begins automatically.

To pause recording

Press REC/PAUSE.

To resume recording, press #.

To stop recording

Press &.

Note

• When you record on @ direction of the tape, the unit stops

recording after recording the side of the tape regardless of the

reverse mode setting in step 2.

The tape counter

The tape counter is useful for searching and locating a

certain point on the tape. Pressing COUNTER RESET

will reset the tape counter to “0000”.

Recording

COUNTER RESET

REC/PAUSEMODE REC LEVEL

DOLBY NR DIRECTION

E-8

ADDITIONAL INFORMATION

If the unit fails to operate normally, check the following points to determine whether the fault can be corrected by the

simple measures suggested. If it cannot be corrected, or if the fault is not listed in the SYMPTOM column, disconnect the

power cord and contact your authorized YAMAHA dealer or service center for help. When taking the service, the RX-E100

/CDX-E100 may be needed. For details, contact your authorized YAMAHA dealer or service center.

Troubleshooting

There is an influence of strong external

noise (lightning, excessive static

electricity, etc.) or a misoperation was

performed while using the unit.

Slack tape wrapped around pinch roller.

Erasure prevention tab is broken off.

Head is dirty.

Tape is worn.

Tape encoded with DOLBY NR B/C is

played back with the unit’s DOLBY NR

OFF or vice versa.

Tape encoded with DOLBY NR B is

played back with the unit’s DOLBY NR C

or vice versa.

Head is dirty.

Head has become magnetized.

Tape is worn.

Slack tape coming out of cassette shell.

Tape is worn.

System cable is not connected.

Silent gaps between tracks are too short.

Excessively soft passages in the middle of

selections.

Conversation, or noise, etc. is recorded.

Turn the unit off and disconnect the AC power

cord from the wall outlet. After about 30 seconds

have passed, connect the power and try again.

Take up slack with a pencil before using.

Replace tape or cover erasure prevention hole with

adhesive tape.

Clean heads.

Replace the tape.

Select an appropriate DOLBY NR type. The same

noise reduction type should be used both on

recording and playback.

Clean heads.

Demagnetize heads with head eraser.

Replace the tape.

Take up slack by turning reels with a pencil.

Replace the tape.

Connect the unit and the RX-E100 / CDX-E100

with the system cable firmly.

The function of searching for the beginning of a

desired track does not operate unless the silent

gaps between tracks are at least four seconds long.

The unit does not work normally.

Tape does not move during

playback or recording.

Cannot record.

Sound is distorted or fades out.

Poor sound quality

Stereo balance is poor.

Excessive noise

Tape travel stops in middle of

playback or recording.

The CD synchronized recording

function does not work.

Cannot search for the beginning of

desired track of the tape

SYMPTOM CAUSE REMEDY

E-9

English

ADDITIONAL INFORMATION

Cassette tapes

• YAMAHA does not recommend the use of 120 minute length cassettes since the extreme thinness of the tape makes them

susceptible to mechanical and recording problems.

• Since the unit automatically detects the tape type, you can use any type of tape.

Notes about cassette tapes

For side A

For side B

Protecting your recordings

• Tapes have removable tabs, which prevent accidental

recording or erasing from taking place. Removing the

tab on the top left protects the side facing you from

erasure. Cover the tab holes with adhesive tape to erase

or record again.

Taking up slack in the tape

• Before loading a tape on the tray, tighten the slack

portion of tape with a pen or pencil.

Maintenance

• Dirty heads, capstans, and pinch rollers can cause poor sound and tape jams. Clean these parts with a commercially

available cleaning tape.

Specifications

Type ..................................................Auto reverse stereo cassette deck

Frequency Response (–20 dB)

Type 1 (Normal) ..................................................... 30 to 15,000 Hz

Type 2 (High).......................................................... 30 to 16,000 Hz

Type 4 (Metal) ........................................................ 30 to 18,000 Hz

Wow and Flutter .......................................................... 0.09%, W.RMS

Signal-to-Noise Ratio ..................................... 58 dB (Dolby NR OFF)

66 dB (Dolby B NR ON)

74 dB (Dolby C NR ON)

Harmonic Distortion ..................................................................... 1.0%

General

Power supply

[U.S.A. and Canada models] ................................AC 120 V, 60 Hz

[Australia model] ..................................................AC 240 V, 50 Hz

[U.K. and Europe models] ....................................AC 230 V, 50 Hz

[General model] ....................... AC 110~120/220~240 V, 50/60 Hz

Power consumption ...................................................................... 12 W

Dimensions (W x H x D)....................................... 217 x 88 x 293 mm

Weight .........................................................................................3.0 kg

Accessories ..............................................................RCA Pin Cable x2

System Control Cable

Specifications are subject to change without notice.

YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.

YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA

YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, F.R. OF GERMANY

YAMAHA ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE

YAMAHA ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD1 7JS, ENGLAND

YAMAHA SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN

YAMAHA MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA

Printed in Malaysia V423640

Yamaha KX-E100 Bruksanvisning

varumärke: Yamaha

Modell: KX-E100

Kategori: Kassettspelare

Typ: Bruksanvisning

Ladda ner pdf

Rapportera

på andra språk

italiano: Yamaha KX-E100 Manuale del proprietario
Deutsch: Yamaha KX-E100 Bedienungsanleitung
français: Yamaha KX-E100 Le manuel du propriétaire
Türkçe: Yamaha KX-E100 El kitabı
English: Yamaha KX-E100 Owner's manual
dansk: Yamaha KX-E100 Brugervejledning
Nederlands: Yamaha KX-E100 de handleiding
română: Yamaha KX-E100 Manualul proprietarului

Yamaha KX-E100 Bruksanvisning

Yamaha KX-E100 Bruksanvisning

på andra språk

Relaterade papper