Hach POLYMETRON 9245 Basic User Manual

DOC024.98.93033

POLYMETRON Model

9245 Sodium Analyzer

08/2016, Edition 11

Basic User Manual

Basishandbuch

Manuale di base per l'utente

Manuel d'utilisation de base

Manual básico del usuario

Grundläggande bruksanvisning

English..............................................................................................................................3

Deutsch.......................................................................................................................... 24

Italiano............................................................................................................................ 47

Français......................................................................................................................... 70

Español.......................................................................................................................... 93

Svenska....................................................................................................................... 116

2

Specifications

Specifications are subject to change without notice.

Specification Details

Measuring range

0 to 10,000 ppb freely programmable

0 to 200 ppm with K-Kit option

Accuracy

Non-cationic application: ± 0.1 ppb or ± 5% of reading, whichever is greater

Cationic application: ± 2 ppb or 5% reading, whichever is greater

Repeatability < 0.02 ppb or 1.5% reading, whichever is greater within 10°C variation

Response time 0.1 to 10 ppb T(90%) = 180 secs

Electrode type pH glass electrode

Number of channels 1 channel

Interference phosphate

10 ppm

Measurement variation less 0.1 ppb

Sample temperature

interference

< 0.5% / °C

Typical environment Power station; Indoor; Demineralized water plant or instrumentation room

Suspended solids < 2 NTU, no oil, no grease

Storage -20 to 60°C (2 to 140°F)

Relative humidity 10 to 80%

Ambient temperature 5 to 50°C (41 to 122°F)

Sample temperature

variation

Stabilization in 10 mins from 15°C to 30°C

pH range of sample

Non-cationic application: 6 to 10 pH

Cationic application: 2 to 10 pH

Flow rate 6 to 9 L/hour

Pressure 0.2 to 6 bar (3 - 87 psi)

Acidity Less than 250 ppm (equivalent CaCO

3

)

Power supply voltage

fluctuation

± 10%

Over voltage category 2 (according to standard EN 61010-1)

Pollution degree 2 (according to standard CEI 664)

Altitude < 2000 m

Measurement category Cat II, Class 1 (overvoltage < 1500V)

Maximum panel dimension

(H x L x D)

850 x 450 x 252.5mm [33.46 x 17.71 x 9.94in]

Inlet

Simple fittings for 6 mm O.D. tubing or ¼" O.D. in PE-low density

¼" OD in PHED-PTFE-SS as option

Outlet Barbed stem for 12 mm (½" I.D.) hose

English 3

Specification Details

Protection rate

Transmitter: IP65 (NEMA 4); Panel: IP50 (dust protection)

Optional Enclosure: IP54 (splash water proof)

Instrument is designed to avoid DIPA vapor inside the enclosure. All DIPA vapor is

collected and sent to the instrument drain

Cell PMMA - compact (minimum tubing)

Flame rate Conform UL

Maximum weight 15 - 30 Kg

Mains power supply 100 - 240 VAC, 50-60 Hz, ± 10%, automatic switching

Max. consumption 80 VA

Fuse 5 x 20 cartridge T2AL-250V following CEI127

Display Last Cal Date, Historical, Concentration, Temperature, Potential

Analog outputs Number: 4; 4-20 or 0-20 mA (650 ohms); Linear / Dual / Logarithm; Smart

Relays 2 x Relay (conc); 1 x Warning; 1 x System

Logic input Start / Standby; Remote AutoCal

EMC requirements

EN61326-1: EMC Directive

Note: This is a Class A product. In a domestic environment this product may cause radio

interference in which case the user may be required to take adequate measures.

N O T I C E

Measurement variations of less than 5% of the full range can occur if the

instrument is subject to a strong electromagnetic field.

Korean registration

User Guidance for EMC Class A Equipment

업무용을 위한 EMC 등급 A 장치에 대한

사용자 지침

사용자안내문

A 급 기기 ( 업무용 방송통신기자재 )

이 기기는 업무용 (A 급 ) 전자파적합기기로서 판매자 또는 사용자는 이 점을 주의

하시기 바라며 , 가정외의 지역에서 사용하는 것을 목적으로 합니다.

CE compliance EN61010-1: LVD Directive

International standards cETLus

Warranty Instrument: 1 year (EU: 2 years)

Electrodes: 6 months

General information

In no event will the manufacturer be liable for direct, indirect, special, incidental or consequential

damages resulting from any defect or omission in this manual. The manufacturer reserves the right to

make changes in this manual and the products it describes at any time, without notice or obligation.

Revised editions are found on the manufacturer’s website.

Safety information

N O T I C E

The manufacturer is not responsible for any damages due to misapplication or misuse of this product including,

without limitation, direct, incidental and consequential damages, and disclaims such damages to the full extent

permitted under applicable law. The user is solely responsible to identify critical application risks and install

appropriate mechanisms to protect processes during a possible equipment malfunction.

4 English

Please read this entire manual before unpacking, setting up or operating this equipment. Pay

attention to all danger and caution statements. Failure to do so could result in serious injury to the

operator or damage to the equipment.

Make sure that the protection provided by this equipment is not impaired. Do not use or install this

equipment in any manner other than that specified in this manual.

Use of hazard information

D A N G E R

Indicates a potentially or imminently hazardous situation which, if not avoided, will result in death or serious injury.

W A R N I N G

Indicates a potentially or imminently hazardous situation which, if not avoided, could result in death or serious

injury.

C A U T I O N

Indicates a potentially hazardous situation that may result in minor or moderate injury.

N O T I C E

Indicates a situation which, if not avoided, may cause damage to the instrument. Information that requires special

emphasis.

Precautionary labels

Read all labels and tags attached to the product. Personal injury or damage to the product could

occur if not observed. A symbol on the instrument is referenced in the manual with a precautionary

statement.

This symbol, when noted on a product, indicates a potential hazard which could cause serious

personal injury and/or death. The user should reference this instruction manual for operation and/or

safety information.

This symbol, when noted on a product enclosure or barrier, indicates that a risk of electrical shock

and/or electrocution exists and indicates that only individuals qualified to work with hazardous

voltages should open the enclosure or remove the barrier.

This symbol, when noted on the product, indicates the presence of devices sensitive to electrostatic

discharge and indicates that care must be taken to prevent damage to them.

This symbol, when noted on a product, indicates the instrument is connected to alternate current.

Electrical equipment marked with this symbol may not be disposed of in European domestic or

public disposal systems. Return old or end-of-life equipment to the manufacturer for disposal at no

charge to the user.

Products marked with this symbol indicates that the product contains toxic or hazardous substances

or elements. The number inside the symbol indicates the environmental protection use period in

years.

Products marked with this symbol indicates that the product conforms to relevant South Korean

EMC standards.

English 5

Overview

Figure 1 Front and rear panels

1 User interface 7 Frame for panel mounting

2 Overflow vessel 8 Reagent canister holder

3 Measuring cell 9 Local controller box

4 Sample flow adjustment valve 10 Electrolyte reservoir

5 Door lock 11 Pump box

6 Reagent shelf 12 Sample inlet valve

Installation

W A R N I N G

The analyzer should only be assembled by qualified staff. Mains power should only be connected once

installation has been completed and checked

Mounting the analyzer

W A R N I N G

Do not connect power prior to mounting and plumbing the instrument.

C A U T I O N

Personal injury hazard. Instruments or components are heavy. Use assistance to install or move. Make sure that

the wall mounting is able to hold 4 times the weight of the equipment.

C A U T I O N

Wherever the analyzer is to be mounted, it is important to note that it must be placed in an upright position with

the transmitter at the top. It is recommended to use a spirit level to ensure that the analyzer is correctly positioned

and not leaning to one side or forward. This is essential to guarantee the accuracy of the analyzer.

6 English

Panel mounting

Mount the analyzer using the fixation holes located around the outside of the analyzer.

Wall mounting

Use the wall mounting kit to fix the instrument to the wall. The distance between the two pieces is

460 mm.

C A U T I O N

It is extremely important to respect this gap of 460 mm to avoid bending the cabinet out of shape while fitting.

Mains power connection

W A R N I N G

No intervention should be made on the instrument without first switching off the power.

The electrical installation should be carried out by duly qualified personnel. A supply voltage of

100-240 VAC is acceptable without changing the configuration. The power supply terminals can be

removed from their housing to make connection easier.

For safety reasons, it is imperative to respect the working procedure below:

• Use a three-wire power cable (live + neutral + earth), sized for supplying the required power.

• The instrument should be connected to the mains via a circuit-breaker or fuse whose value should

be less or equal to 20 A. It should be located in proximity and be identified. This connection should

cut-off the live and the neutral when electrical problems occur or when the user wishes to

intervene inside the instrument. On the other hand, the earth conductor should always be

connected.

The main cabinet should be open with access to the interior.

1. Pass the power cable through the cable gland located at the back left of the bottom of the

cabinet.

2. Open the back of the local controller box (No. 11 in Figure 1 on page 6) by unscrewing the

6 screws.

3. Unscrew the two holding screws on the upper left and right side of the box, and allow it to rotate

down to reveal the back of the transmitter. The cable gland for the power cable is located left and

nearest to you.

4. Unscrew the cable gland nut, pass the power cable through it, and then up through the cable

gland and into the transmitter (No. 2). Screw back the cable gland nut to secure the power cable.

5. Open the transmitter front door by unscrewing the four holding screws.

6. Swing open the door (it is hinged to the left) to reveal the inside of the transmitter.

7. Remove the metallic shielding plate (No. 1) protecting access to the main board.

8. Remove the power supply connector (No. 3) and note where the earth, neutral and live (E, N, L)

must be connected.

9. Connect the power supply cables to the connector.

English

7

10. Put the connector back in place (No. 4).

11. Replace the metallic shielding plate, ensuring it is in front of the power cable just installed.

External communications connection

1. Run the communications cable through an external cable gland on

the bottom of the cabinet, and into the analyzer.

2. Pass it through the cable gland located right and farthest from you

on the base of the transmitter, so it appears inside the transmitter

through the left front cable gland.

3. Connect the communication cable as indicated. Connection is the

same on the CPU board for both the JBUS/ MODBUS and

PROFIBUS options.

4. Close the transmitter door and secure in place with the 4 screws.

5. Put the local controller box back in its normal position and secure in

place with the 2 holding screws.

Input/Output connections

Before using any of the cable glands, perforate first with a screwdriver. To ensure a good seal, the

external diameter of the cables should be between 5 and 7 mm. The nomenclature given in the

connections column of the following table refers to the same nomenclature that is printed on the I/O

board against each available connection.

Connections Function

Re1 to Re2 User relays - see Alarms on page 15 for more information on the relays

Re7 Warning alarm

Re8 System alarm

In2 For remote calibration

In7 To put the analyzer on standby

Iout0 Used for the current measurement signals

Iout1 to Iout3 Can be freely linked to different parameters like measurement, temperature - refer to the

section entitled mA outputs on page 16 for details

On completion, close the local controller box (No. 11 in Figure 1 on page 6) and secure in place with

the 6 screws.

Sample tubes installation

Connecting the sample

Use new tubes for connections during installation

• Exterior Ø: 6 mm exactly (or ¼'')

• Material: polyethylene or PTFE or FEP

• Flow rate: 6 to 9 L/hour

• Pressure: 0.2 to 6 bar (8-100 psig)

• Sample acidity: Sample acidity should not be more than 300 ppm CaCO

3

• Temperature: 5 to 45°C

Note: For continuous monitoring of sample with a temperature between 5-10°C it is recommended that the

installation should include a static heat-exchanger system.

At this stage of the installation, make sure that the flow valve is closed. Connect the pipes by

inserting them into the quick release connections found on the bottom of the analyzer under the

sampling block (No. 14 in Figure 1 on page 6). Be sure that the sample line is correctly flushed

8

English

before any connection to avoid particle injection into the hydraulic system. If particulate matter is

present in the sample, pre-filtration is necessary. A filter should be inserted in the sample line. One is

available as an option.

Connecting the drain tube

The drain outlet is located on the bottom of the analyzer. A 12 x 17 mm pipe is delivered with the

analyzer and should be connected to the drain outlet at one end and the other fed to a drain for

sample evacuation.

Reagents installation

The canisters are installed in the canister holder (No. 10 in Figure 1 on page 6).

1. Prepare the reagents.

2. Install and connect the conditioning solution (diisopropylamine).

3. Install and connect the reactivation solution (blue R label).

4. If you have this option, install and connect the auto calibration solution

(yellow CAL label).

Magnetic stirrer installation

1. On the front of the panel, remove the plastic bag from the overflow vessel (No. 5 in Figure 1

on page 6).

2. Remove the magnetic stirrer from the bag and install it in the overflow vessel.

Reagents volume declaration

Note: As you will now be using the analyzer menus to input data, it may be useful to familiarize yourself with the

data entry procedures by reading the section entitled User interface on page 11.

1. Open the sample valve and check that there is no leakage in the hydraulic path.

2. Power on the analyzer.

3. Select the Menu option from the display.

4. Select MAINTENANCE/DIAG. from the main menu and press Enter.

5. Select the REAGENT CHANGES option and press Enter.

6. Set the BOTTLES FULL parameter to Yes and press Enter.

7. Press Esc to return to the MAINTENANCE/DIAG. menu.

Flow rate adjustment

1. From the MAINTENANCE/DIAG. menu select START UP and press Enter.

2. First, the system automatically primes both the calibration and reactivation tubes.

3. Check that there are no air bubbles in the reagent tubes for reactivation and auto calibration.

4. The next step allows you to regulate the sample flow rate on the measurement channel.

5. The analyzer automatically empties and refills the overflow vessel to determine the flow rate

which is displayed on screen.

6. The flow rate should be 6 to 9 L/hour.

7. Using a screwdriver, regulate the channel’s sample flow (No. 3 in Figure 1 on page 6) by turning

counter-clockwise to increase the flow rate or clockwise to decrease the flow rate.

8. The process is repeated until the flow is correctly regulated for the channel. At this point select

OK.

9. On completion, an Action completed message will be displayed. Select Esc to exit.

English

9

Sample pH conditioning check

Non-cationic applications

1. Install a calibrated pH sensor in the center position of the measurement chamber which is

normally used for the ISE sodium electrode (No. 1 in Figure 1 on page 6).

2. On the analyzer, press Start on the main menu to start the measurement process.

3. Check that the pH value of the sample after conditioning is greater than 10.5. If not, check the

quality of the conditioning product used.

Cationic applications

1. With a calibrated pH sensor, measure the pH of the sample outside of the analyzer.

2. Determine the gas injection time ratio depending on the sample pH. Enter this value into the

analyzer as described in Total gas/water ratio (cationic applications only) on page 14. The

standard values are:

• pH = 2.0 - Tgas/Twater ratio = 180%

• pH = 2.3 - Tgas/Twater ratio = 80%

• pH = 2.6 - Tgas/Twater ratio = 50%

• pH = 2.9 - Tgas/Twater ratio = 30%

• pH = 3.5 - Tgas/Twater ratio = 15%

• pH = 4.0 - Tgas/Twater ratio = 10%

3. Install the same pH sensor in the center position of the measurement chamber (No. 2 in Figure 1

on page 6).

4. On the analyzer, press Start on the main menu to start the measurement process.

5. Measure the pH in the conditioned sample to check if the pump ratios are efficient enough to

obtain a pH of around 11.0. If necessary, update the ratio to maintain a final constant pH of 11.0 ±

0.2.

Reference electrode installation

1. Remove the reference sensor from its box.

2. Remove the plastic reservoir from the bottom (the storage solution is KCl 3M) and install the O-

ring as shown.

3. With care, turn the bottom electrolyte tube ferrule with a maximum ¼ turn to lock it.

4. Remove the plastic plug on the entry port.

5. Install the reference electrode in the extreme left measurement chamber (No. 2 in Figure 1

on page 6).

6. Connect the reference cable (the one without the blue label on it) to the reference electrode.

7. Connect the electrolyte tube to the entry port on the reference electrode.

Sodium ion selective electrode installation

Note: It is critical to preserve the integrity of the sodium ion selective electrode as much as possible. This is why

this electrode must be installed at the very last moment after all other adjustments.

10

English

1. Remove the sodium ion selective sensor from its box.

2. Remove the plastic reservoir from the bottom (the storage solution is standard tap

water) and shake gently (as you would a thermometer) to dispose of any bubbles.

3. Install the O-ring as indicated right.

4. Install the ISE in the center position of the measurement chamber (No. 1 in Figure 1

on page 6).

5. Connect the AS7 cable (with the blue label) to the electrode.

C A U T I O N

After the electrodes installation, it is very important that none of the electrode heads are touching the bottom part

of the measuring cell.

Fill electrolyte reservoir

The electrolyte reservoir is located at the back of the analyzer (No. 12 in Figure 1 on page 6).

1. Take the KCl electrolyte bottle and insert the tip of the tapered spout into the reservoir inlet tube

as far as it will go but without exerting any extra pressure.

2. Squeeze on the bottle as many times as necessary to fill the reservoir to about 3/4 of its capacity.

If you have any difficulty filling the reservoir, raise the spout of the bottle very slightly to avoid an

airlock.

3. Using thumb and forefinger, pump on the electrolyte tube between the reservoir and the

reference electrode to remove any air bubbles that may have formed.

4. If necessary, clean any KCl drops from the analyzer and the reservoir.

Analyzer stabilization

At this stage the analyzer has been completely installed, but needs to run for a period of time to

stabilize.

1. Press Start on the main menu to start the measurement process.

2. Leave the system to run for a couple of hours before starting any calibrations.

User interface

Function keys

The display panel has 5 function keys (illustrated below) to allow menu option selection, field

selection, and data entry options.

• The Esc key cancels data input or goes back to the previous screen.

• The Enter key validates the input and goes on to the next step

• The Up Arrow keys select the option displayed immediately above them on the screen.

When a screen requiring data entry is displayed, the first editable field is always highlighted. To

select other fields on the screen, scroll through them by pressing the Up Arrow function key under

the Select option. As each field is selected, the data element available for update is highlighted.

The same is also true when a menu is displayed. In this case, the first available option is always

highlighted. Scroll to the required option by pressing the Up Arrow function key under the Select

option.

English

11

Data entry is effected in a variety of ways depending on the characteristics of the data field being

accessed.

Numeric fields

These fields require that the user enter one or more numeric values into a field. The type of field

determines the available input. In some fields only digits 0 through 9 would be available to select

whereas in other fields the decimal point and/or minus sign may also be available.

1. For data elements such as these, press the function key under either the Up Arrow or Down

Arrow options to initiate data entry.

2. The first digit will then be highlighted, and a new Right Arrow option replaces the Select option

at the bottom of the screen.

3. Press the function key under the Up Arrow option to increase the value of the field by 1.

4. Press the function key under the Down Arrow option to decrease the value of the field by 1.

5. Press the function key under the Right Arrow option to accept the currently displayed digit and

move one digit to the right.

6. Press the Enter function key to accept the data and move to the next input field.

Alphanumeric fields

These fields require that the user enter one or more alphanumeric values into a field. The type of

field determines the available input. In some fields only upper case alpha characters may be allowed,

in others upper and lower case alphanumeric characters my be allowed, etc.

1. Press the function key under either the Up Arrow or Down Arrow options to initiate data entry.

2. The first character will then be highlighted, and a new Right Arrow option replaces the Select

option at the bottom of the screen.

3. Press the function key under the Up Arrow or Down Arrow option to scroll through the list of

available characters.

4. Press the function key under the Right Arrow option to accept the currently displayed character

and move to the next character.

5. Press the Enter function key to accept the complete field and move to the next data input field.

List element fields

This type of data entry is where a pre-defined list of available data values are available to the user

who must select the one which is applicable. Free-format text is not allowed.

1. For data elements such as these, press the function key under the Up Arrow option to scroll

forward through the pre-defined list or press the function key under the Down Arrow option to

scroll backward through the list.

2. When the required list element is displayed press the Enter function key to accept the data and

move to the next data input field.

Incremental value fields

These are fields where a value is displayed on the screen and the user has the option of increasing

or decreasing the value.

1. Use the Up Arrow function keys under the plus or minus symbols to adjust the value by 1.

2. On completion press the Enter function key, to accept the new value.

12

English

Measurement screens

Principal display

1. Sample being measured

2. Bar graph of measurement progress

3. Current measurement graph

4. Time

5. Current measurement and unit

6. Temperature

The options at the bottom of the screen will include three of the following:

• Hist - Selecting this option will show the most recent measurements along with the last grab

sample and verification details.

• Stop - Select this option to stop the current process on the analyzer. This could be a

measurement, verification or grab sample process. The option is only available when one of these

processes is currently running. You will be asked for confirmation (YES or NO) that you want to

stop the process.

• Start - Select this option to start the analyzer measurement process. This option is only available if

the analyzer has been stopped.

• Menu - This will bring up the main menu screen.

• Alarm - This option will appear flashing on the screen if any alarms have been set. Selecting this

option will take you to the alarms screen.

Main menu

The main menu is accessible from any one of the measurement screens. To access the main menu

screen press the Up Arrow function key under the Menu option.

Note: Access to the Main Menu will require a password if a PROGRAMMING password has been set (see

Passwords on page 14).

The first option in the menu will always be highlighted by default. To scroll to the option required,

press the Up Arrow function key under the Select option. Detailed information on each of the main

menu options is available elsewhere in this manual as follows:

• VERIFICATION - See section entitled VERIFICATION on page 20

• GRAB SAMPLE - See section entitled GRAB SAMPLE on page 21

• CALIBRATION - See section entitled CALIBRATION on page 17

• MAINTENANCE/DIAG. - See section entitled MAINTENANCE/DIAG. on page 21

• USER SETUP - See section entitled USER SETUP on page 14

• SYSTEM SETUP - See section entitled SYSTEM SETUP on page 13

SYSTEM SETUP

Date and time

1. Select the DATE/TIME option to access the date/time sub-menu.

2. Scroll to the required day and press the Enter function key.

3. Enter the day, month, and year.

English

13

4. Enter the time in HH:MM:SS format (24 hour clock).

5. On completion press Esc to return to the main System Setup menu.

Display options

1. Select the DISPLAY option to set up the display parameters.

2. Select the LANGUAGE, CONC. UNIT and TEMPERATURE UNIT fields in turn, and set your

preferences by scrolling through the available options.

Passwords

1. Select the PASSWORDS option to set passwords for access to programming, calibration and

system setup options.

2. Each password is a 4-digit numeric field. Enter the required value for each of the three

passwords. A value of 0000 signifies no password is required to gain access to those menu

options.

Default values

1. Select the DEFAULT VALUES option to erase all the previously set user parameters and load

the default values. A warning message is displayed and confirmation of this action is required.

2. To exit from the screen without loading the default values, press the Esc function key.

3. To load the default values, select the Yes option.

Adjust mA output

1. Select the ADJUST mA OUTPUT option to access the analyzer’s analog output parameters.

2. Select the mA output you wish to change to display the next screen.

3. The option to increase or decrease the low end value (0 mA or 4 mA depending on your setting)

is displayed. Change the value up or down by selecting the Minus or Plus indicators at the

bottom of the screen.

4. On completion press the Enter function key and the display changes to 20 mA.

5. Enter the adjustment value in the same way as for the low end value. On completion press the

Enter function key, and the display reverts back to the main ADJUST mA OUTPUT screen, to

allow you to select the next output to adjust.

USER SETUP

Measurement

Targeted pH (non-cationic applications only)

Select the pH option and enter the target pH value for your application. The measured pH value of

the sample in the measuring cell should be within ±0.2 pH of the target.

Total gas/water ratio (cationic applications only)

Enter the ratio of gas to water to minimize the DIPA consumption.

Measure steps

1. Select the MEASURE STEPS option to set up the measurement timings.

2. The on line measurement time defines the measurement time of the sample and how often the

measurement values are stored in memory. For a single channel configuration, it is

recommended to leave this time at the default value of 10 minutes.

3. If smart rinsing is required after a calibration, grab sample or sensor reactivation, set this

parameter to Yes and define the maximum rinse time.

14

English

Reactivation frequency

1. Select the ACTIVAT. FREQ option to set the time period between electrode reactivation. When

this time period expires, the electrode is reactivated automatically with an injection of a small

amount of reactivation solution.

2. Set the reactivation mode to either a Frequency or a fixed date.

3. If set to frequency, the recommended time period is 24 hours so that the electrode is reactivated

on a daily basis.

Note: If this value is set to zero, then no electrode reactivation will take place during the calibration process and

as such the calibration may be inaccurate. It is highly recommended to set this parameter to 24.

4. If set to a fixed date, define the day and time of the week when reactivation takes place. Set the

day of the week to an asterisk if reactivation is not to take place on that day.

Datalogger setup

1. Select the VIEW DATA option to display the requested data.

2. All information matching the parameters selected in the VIEW SETUP option is displayed on the

screen. If the data covers more than one screen, an Arrow key will be displayed at the bottom.

Use this key to scroll through the data.

3. Select the VIEW SETUP option to define the parameters for the data you wish to view.

4. The FROM data field is the date (DD/MM/YY) from which you want to start viewing data.

5. The AT data field is the time (HH:MM:SS format) from which you want to start viewing the data.

6. The CH field defines the channel for which you want to view the data.

7. If you wish to see the ALARMS information (both system and warning alarms), select Yes in this

field, or No if alarm information is not required.

Graph time base

For graphical displays, enter the number of hours as the base line for the graph.

Alarms

1. Select the ALARMS option to set up the parameters for all the alarms including the system and

warning alarms.

2. Select the alarm to set up.

3. General alarms:

Mode

Limit Trigger the alarm when the measurement is above or below a pre-defined limit

Sample flow Trigger the alarm when the sample flow rate is too low

Active channel Trigger the alarm when the channel is active

Attributes Channel n Defines the channel number on which the alarm is triggered

Limit nnnn Define the limit when the alarm should be triggered

Direction

Up Trigger alarm when measurement is above the limit

Down Trigger alarm when measurement is below the limit

Delay nnn seconds The delay before the alarm is activated

Hysteresis nn% Hysteresis %

Relay

N.O. Normally open

N.C. Normally closed

4. Warning alarm:

English

15

Alarm

Yes Activate the warning alarm

No Deactivate the warning alarm

Accept

Manual When the alarm is triggered, turn it off by pressing the Enter function key

Auto

When the alarm is triggered, it will turn itself off only when the reason for the alarm being

triggered is no longer valid

Relay

N.O. Normally open

N.C. Normally closed

5. System alarm:

Alarm

Yes Activate the system alarm

No Deactivate the system alarm

Relay

N.O. Normally open

N.C. Normally closed

mA outputs

1. Select the mA OUTPUTS option to set up the parameters for all the analog outputs.

2. From the list available, select the mA output you wish to set.

Output parameters

1. Analog output parameters:

Attribute

Choose the attribute that triggers the analog output.

Note: The attribute variable cannot be applied to Output 0, which is reserved for the continuous live output signal.

Type Choose either a 0-20 mA or 4-20 mA analog output

Mode Select the mode. This parameter is only selectable if the attribute is set to a measurement channel

Low The value corresponding to the low end of the scale

Middle The value corresponding to the mid-point of the scale (only available in dual mode)

High The value corresponding to the high end of the scale

Event indication

1. Select the EVENT INDICATION option in the mA Outputs menu to display the options available

for event setting.

2. Select the option for which you want to set an event.

3. Define the attribute for the event. This is one of the outputs or None.

4. The MODE can be either a Preset val or Frozen.

5. If a preset value is chosen, you will be required to enter the value of the analog output that will be

forced, when that event occurs.

16

English

Test

This option allows you to enter a value into the mA field. Press the Enter function key to force this

value on all the analog outputs. The value can then be verified with the use of a multimeter

connected to the analyzer.

RS485 (or PROFIBUS)

Note: If the PROFIBUS option has been installed, then the menu option will show PROFIBUS rather than RS485,

and the PROFIBUS parameters will need to be installed.

1. Select the RS485 option to set up the parameters for the communications protocol.

2. Press the Enter function key to accept each data element.

3. On completion, press the Esc function key to return to the user setup screen.

Sample channels

Select the SAMPLE CHANNELS option to set up the channel parameters.

Channel activation

Using the Up and Down Arrow keys, define whether the channel is active (Activ) or inactive

(Inactiv).

Sequence

The default sequence should be left unchanged.

Channel names

Define the name of the channel with free-format alphanumeric text up to a maximum of 8 characters.

CALIBRATION

The instrument cannot be calibrated until at least one complete measurement cycle has been

successfully performed. An attempt to calibrate the instrument before this will result in a “Not

authorized” message being displayed.

In order to obtain accurate measurement results, the analyzer should be calibrated on a regular

basis. Two basic methods of calibration are available:

• Automatic calibration - Parameters can be set up so that the analyzer will perform a calibration

automatically on pre-defined days at a pre-defined time (see Automatic calibration setup

on page 19). This type of calibration is always done using known calibration solution

concentrations.

• Manual calibration - The user can manually perform a calibration on an ad-hoc basis.

Note: Before starting a calibration It is very important to ensure that the Reactivation Frequency parameter (see

Reactivation frequency on page 15) is greater than zero. If set to zero, the electrode reactivation process will not

take place during calibration and as such the measurement results may well be out of limits.

Calibration solution concentrations

N O T I C E

The maximum concentration value for any calibration solution cannot be greater than 2000 ppm. Any value

superior to this is outside the analyzer specifications and cannot be processed.

Manual calibration

For a manual calibration, the calibration solutions must be between 100 ppb and 2000 ppm and

must respect the following rules:

• LOW CAL SOL must be ≥ sample concentration of Na

+

and a minimum of 100 ppb

• HIGH CAL SOL = (LOW CAL SOL x 10)

Example 1: sample concentration of Na

+

= 20 ppb

English

17

→ LOW CAL SOL = minimum value = 100 ppb Na

+

→ HIGH CAL SOL = (100 ppb x 10) = 1000 ppb Na

+

Example 2: sample concentration of Na

+

= 450 ppb

→ LOW CAL SOL = ≥ sample concentration of Na

+

= 500 ppb Na

+

→ HIGH CAL SOL = (500 ppb x 10) = 5000 ppb Na

+

Note: The values LOW CAL SOL and HIGH CAL SOL must be entered into the system (see One point calibration

on page 19 or Two point calibration on page 19).

Automatic calibration

For an automatic calibration, the calibration solution must be between 10 ppm and 2000 ppm and

must respect the following rules:

• CAL SOL minimum = 10 ppm

• CAL SOL = (sample concentration of Na

+

x 1000)

Example 1: sample concentration of Na

+

= 0.1 ppb

→ CAL SOL = minimum value = 10 ppm Na

+

Example 2: sample concentration of Na

+

= 1 ppm

→ CAL SOL = (1 ppm x 1000) = 1000 ppm Na

+

Note: The value CAL SOL must be entered into the system (see Automatic calibration setup on page 19)

Start calibration

Select the START CALIBRATION option to calibrate the analyzer manually.

Calibrate known addition

1. Select the CAL.KNOWN ADDITION option to calibrate the analyzer by mixing the sample with a

known concentration of calibration solution. The concentration of the calibration solution is

defined in Automatic calibration setup on page 19.

2. The instrument first checks that the volume of calibration solution remaining is enough. If not, a

warning alarm is activated and the instrument returns to normal measurement with the original

parameters.

3. If the volume of solution is OK, the background point measurement (P0) to be used as the base

measurement value is taken. This is the measurement against the sample before any additions of

the calibration solution have been made.

4. The measurement must be stable and less than 1 per thousand of the calibration solution

concentration, otherwise the instrument returns to normal measurement with the original

parameters. Provided the measurement is OK, the P0 measurement details are displayed on

screen.

5. If the reactivation frequency parameter is not zero (as is highly recommended), the electrode will

be reactivated.

6. When the reactivation process is complete, the overflow vessel is rinsed to remove all traces of

sample.

7. After rinsing, the overflow vessel is re-filled with sample plus 2mL of the calibration solution.

8. The sample is then measured and the details displayed against P1.

9. When the measurement is stable, the details are displayed at the top of the screen against

measurement P1.

10. The overflow vessel is then rinsed and re-filled with sample plus 20mL of the calibration solution.

11. This sample is then measured and the details displayed against P2.

12. Once the final measurement is stable, the offset and slope for this calibration are calculated.

13. The default values of the offset and slope are displayed along with the calculated values for the

last and current calibration.

14. A message is displayed indicating the success or failure of the calibration.

18

English

One point calibration

This process requires that a calibration solution of known sodium concentration is available. Refer to

Calibration solution concentrations on page 17 for information regarding the concentration of the

calibration solution.

1. Select the MAN.OFFSET CAL option to start the one point calibration process.

2. If necessary, enter the concentration of the calibration solution, and select START to initiate the

calibration process. Then, provided the reactivation frequency parameter is not zero (as is highly

recommended), the electrode is reactivated. On completion this is followed by a rinsing of the

overflow vessel.

3. When prompted, fill the overflow vessel with the calibration solution and select OK to start the

measurement.

4. The calibration solution is measured and the results displayed.

5. Once the final measurement is stable, the offset for the calibration is calculated.

6. A message is displayed indicating the success or failure of the calibration.

Two point calibration

This process requires that two calibration solutions of known sodium concentrations are available.

Refer to Calibration solution concentrations on page 17 for information regarding the concentrations

of the calibration solution.

1. Select the MAN.OFFSET+SLOPE CAL option to start the two point calibration process.

2. If necessary, enter the concentrations of the calibration solution, and select START to initiate the

calibration process. Then, provided the reactivation frequency parameter is not zero (as is highly

recommended), the electrode is reactivated. On completion this is followed by a rinsing of the

overflow vessel.

3. The process is then very similar to the one-point calibration above, except after the instrument

measures the low value calibration solution, the overflow vessel will be rinsed and you will be

asked to fill it with the high value calibration solution.

4. A message is displayed indicating the success or failure of the calibration.

Automatic calibration setup

This allows the analyzer to be automatically calibrated at pre-defined and regular intervals. The

process is the same as described in Calibrate known addition on page 18 except it is initiated

automatically at the pre-defined time.

1. Select the AUTO. CAL. SETUP option to access its sub-menu and set the calibration

parameters.

2. Turn the automatic calibration on or off by selecting Yes or No as appropriate. Note that even if

this is set to Yes, it is still possible to calibrate the analyzer manually if required.

3. CAL.SOL defines the concentration of the calibration solution. Refer to Calibration solution

concentrations on page 17 for information regarding the concentration of the calibration solution.

4. MODE can either be set up to a fixed date or to a specified Frequency.

5. If the mode is set to fixed date, enter the day(s) of the WEEK when the calibration will be

performed. Set the day to an asterisk to skip that day.

6. Set the HOUR field (HH:MM:SS format on a 24 hour clock) to the time the automatic calibration

should start.

7. If the mode is set to frequency, then the week and hour data fields will be replaced by a TIME

PERIOD field. Enter the calibration frequency in hours into this field.

English

19

Calibration results

After the slope and offset have been calculated, the default parameters, last calibration details and

current calibration details are displayed, along with a “Calibration ok” or “Calibration error”

message. The criteria for accepting or rejecting the calibration is as follows:

• The slope must be within ± 10% of the standard slope

• The offset must be within ± 59 mV from the reference point

If the calibration is accepted, the parameters are updated and the instrument returns to the normal

measurement mode after a short delay.

If the calibration is rejected an alarm is set and the parameters remain unchanged. After a short

delay the analyzer returns to the normal measurement mode.

For details of the calibration results, select the calibration loggings option as described below.

Calibration loggings

1. Select the CALIBRATION LOGGINGS option to view historical information about previous

calibrations.

2. Use the Arrow key to scroll through the data.

Custom adjustment

1. Where the analyzer displays values that are slightly above or below the expected value, the

CUSTOM.ADJ option can be used to manually adjust the measurement value.

2. Enter a positive or negative value which will be added to the measurement value. This option can

only be used to make minor adjustments. The allowable adjustment value is between -0.1 ppb

and +0.1 ppb.

3. If the displayed and expected values differ significantly, the analyzer should be recalibrated.

Temperature calibration

1. Select the TEMPERATURE CALIB. option to calibrate the temperature electrode.

2. The measured temperature reading is displayed in the raw temp field.

3. Take a temperature reading with a certified thermometer and press OK to continue.

4. Then enter this temperature reading into the CAL.TEMP. field.

5. Press OK to calibrate.

VERIFICATION

This option allows you to verify the measurement using a solution of known sodium concentration.

Concentration of the known solution should be higher than 20 ppb (100 ppb is recommended) to

ensure a preparation step in a range with lower risks of contamination.

1. First enter the concentration of the verification solution in the VALID. SOL field.

2. Select START to commence the process.

3. The first step of this cycle allows the reactivation of the electrode. The message SENSOR

ACTIVATION is displayed. Select Yes to reactivate the sensor. Select No if time is more

important than accuracy.

4. The reactivation process is automatically followed by a rinsing of the overflow vessel and

measuring cell using the process sample. Upon completion of the rinsing step, the analyzer is

ready for the first manual step in the cycle.

5. Place the sample level detector on the side and pour approximately 200 mL of the solution into

the overflow vessel, as prompted on screen. Manual introduction is complete when the sample

overflows at the back of the overflow vessel.

20

English

Sidan laddas ...

Hach POLYMETRON 9245 Basic User Manual

Hach POLYMETRON 9245 Basic User Manual

på andra språk

Relaterade papper

Andra dokument