ResMed HumidAire 3i Användarmanual

Kategori
Avfuktare
Typ
Användarmanual

Denna manual är också lämplig för

www.resmed.com Waking people up to sleep
Reorder number: 33804/2 05 05
USER’S MANUAL
English
Svenska
Dansk
Norsk
Suomi
HumidAire 3i
HumidAire 3i
TM
A
B
12
4
D
1 4
1
2
566a
234
3
© 2005 ResMed Ltd.
© 2005 ResMed Ltd. © 2005 ResMed Ltd.
© 2005 ResMed Ltd. © 2005 ResMed Ltd.
C
E
1
2
3
(a)
(a)
Component of 33804/2
ILLUSTRATIONS
ILLUSTRATIONS
ILLUSTRATIONER
ILLUSTRASJONER
KUVAT
Air outlet / Luftutsläpp /
Luftudtag / Luftuttak /
Ilmantuloaukko
Control dial /
Kontrollknapp /
Kontrolknap /
Kontrollskive / Säädin
Docking station /
Dockingstation /
Dockningstation /
Forankringsstasjon /
Liitäntäasema
Heater plate /
Värmeplatta / Varmeplade /
Varmeplate / Lämmityslevy
Latch / Spärrhake /
Klinke / Haspe /
Salpa
Cover / Framstycke / Dæksel /
Deksel / Kansi
Cover seal / Framstyckets försegling /
Tætning til dæksel / Dekselkapsling /
Kannen tiiviste
Connector seal / Kopplingsförsegling /
Tætning til kobling / Koblingsstykkekapsling /
Liitännän tiiviste
Water chamber /
Vannbeholder /
Vattenbehållare /
Vesisäiliö
REMOVING THE FRONT CAP (IF FITTED) / TA BORT FRONTKÅPAN (OM DEN
ÄR INPASSAD) / FJERNELSE AF FRONTDÆKSEL (HVIS RELEVANT) / SLIK TAR DU AV
FRONTDEKSLET (HVIS UTSTYRT MED) / ETUKANNEN IRROTTAMINEN (JOS SE ON
PAIKOILLAAN)
Front cap /
Lock på framsidan /
Frontdæksel /
Frontdeksel /
Etukansi
REMOVING AND STORING THE CONNECTOR PLUG / BORTTAGNING OCH
FÖRVARING AV KOPPLINGSKONTAKTEN / FJERNELSE OG OPBEVARING AF
KOBLINGSFORBINDELSEN / TA AV OG OPPBEVARE TILKOBLINGSPLUGGEN /
LIITÄNTÄTULPAN IRROTTAMINEN JA SÄILYTTÄMINEN
Connector plug / Kopplingskontakt /
Koblingsforbindelse / Tilkoblingsplugg / Liitäntätulppa
ATTACHING YOUR HUMIDAIRE 3i / SÄTTA FAST HUMIDAIRE 3i / PÅSÆTNING AF HUMIDAIRE 3i / KOBLE TIL HUMIDAIRE 3i-APPARATET /
HUMIDAIRE 3i -ILMANKOSTUTTIMEN LIITTÄMINEN
FILLING THE WATER CHAMBER / FYLLA VATTENBEHÅLLAREN / OPFYLDNING AF VANDBEHOLDER / FYLLE VANNBEHOLDEREN / VESISÄILIÖN TÄYTTÄMINEN
33804r2 illos.qxd 25/05/2005 2:53 PM Page 1
I
1 2
34
5
© 2005 ResMed Ltd.
6
F H
3
56
9
1
4
10 min
G
© 2005 ResMed Ltd.© 2005 ResMed Ltd.
© 2005 ResMed Ltd.
2
3
5
4
UNDERSIDE VIEW / BILD UNDERIFRÅN / SET FRA UNDERSIDEN /
VISNING AV UNDERSIDE / NÄKYMÄ ALHAALTA
7
8
1
10 min
2
Large silver button /
Stor silverknapp /
Stor sølvknap /
Stor sølvfarget knapp /
Hopeanvärinen painike
Press button and pull apart / Tryck på knappen och dra isär /
Tryk på knappen og træk delene fra hinanden / Trykk inn knappen og
trekk fra hverandre / Paina painiketta ja vedä osat erilleen
STARTING YOUR TREATMENT / STARTA BEHANDLINGEN / INDLEDNING AF
BEHANDLINGEN / START AV BEHANDLING / HOIDON ALOITTAMINEN
Right key / Höger knapp /
Højre tast / Høyre tast /
Oikea näppäin
Up/Down keys /
Upp/Ner knappar /
Op/Ned-taster /
Opp/ned-taster /
Ylös/alas-näppäimet
Start/Stop key / Start/Stop knapp /
Start/Stop-tast / Start/Stans-tast /
Käynnistys/pysäytys-näppäin
Control dial /
Kontrollknapp /
Kontrolknap /Kontrollskive
/ Säädin
Indicator light / Ljusindikator /
Indikatorlys / Indikatorlampe /
Merkkivalo
Control panel / Kontrollpanel /
Kontrolpanel / Kontrollpanel /
Ohjauspaneeli
Left key / Vänster knapp /
Venstre tast / Venstre tast /
Vasen näppäin
DETACHING YOUR HUMIDAIRE 3i / TA BORT HUMIDAIRE 3i / FRAKOBLING AF HUMIDAIRE 3i /
FRAKOBLING AV HUMIDAIRE 3i-APPARATET / HUMIDAIRE 3i -ILMANKOSTUTTIMEN IRROTTAMINEN
DISASSEMBLING YOUR HUMIDAIRE 3i / TA ISÄR HUMIDAIRE 3i / DEMONTERING AF HUMIDAIRE 3i /
DEMONTERING AV HUMIDAIRE 3i-APPARATET / HUMIDAIRE 3i -ILMANKOSTUTTIMEN PURKAMINEN
RE-ASSEMBLING YOUR HUMIDAIRE 3i / SÄTTA IHOP HUMIDAIRE 3i /
SAMLING AF HUMIDAIRE 3i / SETTE SAMMEN HUMIDAIRE 3i-APPARATET IGJEN /
HUMIDAIRE 3i -ILMANKOSTUTTIMEN KOKOAMINEN
33804r2 illos.qxd 25/05/2005 2:54 PM Page 2
USERS MANUAL 1
B
RUGERMANUAL 41
B
RUKSANVISNING 21
B
RUKERHÅNDBOK 61
HUMIDAIRE 3i
ENGLISHSVENSKANORSK DANSKSUOMI
KÄYTTÖOHJE 83
33804r2.book Page iii Wednesday, May 25, 2005 2:54 PM
Patents and designs pending.
HumidAire, HumidAire 3i, S8 and SmartStart are trademarks of ResMed Ltd and HumidAire is registered in
U.S. Patent and Trademark Office.
© 2005 ResMed Ltd.
Manufactured by:
ResMed Ltd 1 Elizabeth MacArthur Drive Bella Vista NSW 2153 Australia
Tel: +61 (2) 8884 1000 or 1 800 658 189 (toll free) Fax: +61 (2) 8883 3114 Email: [email protected]
Distributed by:
ResMed Corp 14040 Danielson Street Poway CA 92064-6857 USA
Tel: +1 (858) 746-2400 or 1-800-424-0737 (toll free) Fax: +1 (858) 746-2900 Email: [email protected]
ResMed (UK) Limited 65 Milton Park Abingdon Oxfordshire OX14 4RX UK
Tel: +44 (1235) 862 997 Fax: +44 (1235) 831 336 Email: rece[email protected]
ResMed Asia Pacific Ltd 97 Waterloo Road North Ryde NSW 2113 Australia
Tel: +61 (2) 9886 5000 or 1 800 991 900 (toll free) Fax: +61 (2) 9889 1471 Email: [email protected]
ResMed Austria GmbH Purtscherstraße 18, 9500 Villach Österreich
Tel: 43 (4242) 430 830 Fax: +43 (4242) 430 830-4 Email: rece[email protected]
ResMed BV Nieuwe Parklaan 86, 2587 BV Den Haag Nederland
Tél: +31 (70) 358 6263 Fax: +31 (70) 358 4333 Email: recept[email protected]
ResMed Finland Niittykatu 6 FIN 02200 ESPOO Suomi
Puh: +358 9 8676820 Faksi: +358 9 86768222 Sähköposti: reception@resmed.fi
ResMed GmbH & Co. KG Fraunhoferstraße 16, 82152 Martinsried Deutschland
Tel: +49 (0) 89/99 01-00 Fax: +49 (0) 89/99 01-10 55 Email: [email protected]
ResMed Hong Kong Limited Room 1714, Miramar Tower 132-134 Nathan Road Tsim Sha Tsui Hong Kong
Tel: +852 2366 0707 Fax: +852 2366 4546 Email: receptio[email protected]
ResMed Japan Nihonbashi Hisamatsu Bldg. 4F, 2-28-1 Nihonbashi-Hamacho, Chuo-Ku, Tokyo 103-0007, Japan
Tel: +81 (3) 3662 5056 Fax: +81 (3) 3662 5040
ResMed Malaysia Sdn Bhd Suite E-10-20, Plaza Mon’t Kiara No. 2 Jalan 1/70C Mon’t Kiara 50480 Kuala Lumpur
Malaysia Tel: +60 3 6201 7177 Fax: +60 3 6201 2177 Email: reception@resmed.com.my
ResMed NZ Ltd PO Box 51-048 Pakuranga Auckland New Zealand
Tel:+64 274 737 633 Fax:+64 9 239 0193 Email: reception@resmed.co.nz
ResMed SA Parc de la Bandonnière 2, rue Maurice Audibert 69800 Saint-Priest France
Tél. : +33 (0) 4 37 251 251 Fax : +33 (0) 4 37 251 260 Email: [email protected]
ResMed Singapore Pte Ltd 238A Thomson Road #12-03/04, Novena Square, Tower A Singapore 307684
Tel: +65 6284 7177 Fax: +65 6284 7787 Email: reception@resmed.com.sg
ResMed Spain SL C/Arturo Soria, 245 28033 Madrid España
Tel: +34 (93) 5908154 Fax: +34 (93) 5908153 Email:angelo@resmed.es
ResMed Sweden AB Industrigatan 2 S-461 37 Trollhättan Sverige
Tel: +46 520 420 110 Fax: +46 520 397 15 Email: [email protected]
Labhardt AG Thannerstrasse 57 CH-4054 Basel Schweiz
Tel: +41 (061) 307 9711 Fax: +41 (061) 307 9722 Email: [email protected]
US DESIGNATED AGENT: ResMed Corp
EU AUTHORISED REPRESENTATIVE: ResMed (UK) Ltd
Internet: www.resmed.com
33804r2.book Page iv Wednesday, May 25, 2005 2:54 PM
ENGLISH
1
USER’S MANUAL
English
HumidAire 3i
33804r2.book Page 1 Wednesday, May 25, 2005 2:54 PM
2
CONTENTS
WELCOME . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
WHAT IS THE HUMIDAIRE 3i? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Y
OUR RESPONSIBILITY 3
MEDICAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
I
NTENDED USE 4
C
ONTRAINDICATIONS 4
W
ARNINGS 4
COMPONENTS OF YOUR HUMIDAIRE 3i . . . . . . . . . . . . . . . . . . . . . . . . . . 5
SETTING UP YOUR HUMIDAIRE 3i FOR USE . . . . . . . . . . . . . . . . . . . . . . . 5
R
EMOVING THE FRONT CAP (IF FITTED) 5
R
EMOVING AND STORING THE CONNECTOR PLUG 6
A
TTACHING YOUR HUMIDAIRE 3i 6
F
ILLING THE WATER CHAMBER 6
STARTING AND STOPPING TREATMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
S
TARTING YOUR TREATMENT 7
S
TOPPING YOUR TREATMENT 8
D
ETACHING YOUR HUMIDAIRE 3i 8
FREQUENTLY ASKED QUESTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
CLEANING AND MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
D
ISASSEMBLING YOUR HUMIDAIRE 3i 10
C
LEANING YOUR HUMIDAIRE 3i 11
R
EASSEMBLING YOUR HUMIDAIRE 3i 11
S
ERVICING 12
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
TECHNICAL SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
INDEX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
33804r2.book Page 2 Wednesday, May 25, 2005 2:54 PM
3
WELCOME
ENGLISH
WELCOME
Thank you for choosing the ResMed HUMIDAIRE 3i™ humidifier. The HUMIDAIRE 3i
is designed to humidify (moisten) the air delivered to your airway during CPAP
(continuous positive airway pressure) therapy. The H
UMIDAIRE 3i attaches to your
ResMed S8™ Series CPAP flow generator with a simple ‘click-in’ mechanism.
This user manual contains the information you need for the correct use of your
H
UMIDAIRE 3i.
WHAT IS THE HUMIDAIRE 3i?
The HUMIDAIRE 3i is designed to form a single unit with a ResMed CPAP flow
generator. The combined unit provides humidification during CPAP therapy, and can
make therapy more comfortable.
You may have experienced nasal congestion or dryness of the nose, mouth, or throat
during CPAP therapy. These symptoms are caused by dry climates, cold air
temperatures, the airflow delivered from your flow generator, or mouth leak. Moist air
may help relieve these symptoms of dryness.
Refer to your flow generator manual to see whether it is compatible with the
H
UMIDAIRE 3i. Contact your equipment supplier or ResMed office if you require
further information.
YOUR RESPONSIBILITY
You or the user of this system shall have sole responsibility and liability for any injury
to persons or damage to property resulting from:
operation which is not in accordance with the operating instructions supplied
maintenance or modifications carried out unless in accordance with authorised
instructions and by authorised persons.
Please read this manual carefully before use.
This manual contains special terms and icons that appear in the margins to draw your
attention to specific and important information.
Warning alerts you to possible injury.
Caution explains special measures for the safe and effective use of the device.
Note is an informative or helpful note.
33804r2.book Page 3 Wednesday, May 25, 2005 2:54 PM
4
MEDICAL INFORMATION
INTENDED USE
The HUMIDAIRE 3i is indicated for humidification of the air delivered from the ResMed
S8 Series CPAP devices. The H
UMIDAIRE 3i is for use only as recommended by a
physician.
CONTRAINDICATIONS
The HUMIDAIRE 3i is contraindicated for use with patients whose upper (supraglottic)
airway has been bypassed. Please also refer to the relevant system manual for
contraindications associated with CPAP therapy.
WARNINGS
The following are general warnings. Specific warnings and cautions appear next to the
relevant instructions in the manual.
!
WARNINGS
Use the HUMIDAIRE 3i only for its intended use as described in this manual.
Make sure that the water chamber is empty and thoroughly dried before
transporting the H
UMIDAIRE 3i.
The HUMIDAIRE 3i is designed only for use with specific ResMed CPAP devices.
Do not use the H
UMIDAIRE 3i with any other CPAP device.
The HUMIDAIRE 3i should only be used with delivery tubes or accessories
recommended by ResMed. Connection of other delivery tubes or accessories
could result in injury, or damage to the device.
The HUMIDAIRE 3i, including the associated tubing, is for single-patient use and
must not be re-used on another person. This is to avoid the risk of cross-infection.
Always place the HUMIDAIRE 3i device lower than the level of the patient. If it is
placed at or above the level of the patient, heated water may flow down the air
tubing and into the mask.
There exists the possibility that if the device is placed above the level of the patient
and is tipped over, or if the tubing is filled with condensate, the mask might fill with
water. The H
UMIDAIRE 3i should therefore be used with caution in patients who
are unable to guard their airways, or are unable to pull the mask off, for example
following a stroke. Attention should be given to the relative risks and benefits.
Do not attempt to dismantle the HUMIDAIRE 3i docking station. There are no
user-serviceable parts inside. Repairs and internal servicing should only be
performed by an authorised service agent.
Take care when handling the HUMIDAIRE 3i. The heater plate and the water in the
water chamber may be hot.
If liquids are inadvertently spilled into or on the HUMIDAIRE 3i docking station,
unplug the CPAP device from the power outlet. Disconnect the docking station
from the CPAP device and allow the docking station to drain and dry before using.
33804r2.book Page 4 Wednesday, May 25, 2005 2:54 PM
5
COMPONENTS OF YOUR HUMIDAIRE 3i
ENGLISH
Do not operate the HUMIDAIRE 3i if the CPAP device has a damaged power cord
or plug.
Do not operate the HUMIDAIRE 3i if it is not working properly or if any part of it
has been dropped or damaged.
Keep the CPAP device power cord away from heated surfaces.
Do not drop or insert any object into any opening or tubes.
Do not use the HUMIDAIRE 3i in the presence of flammable or explosive
materials.
Explosion hazard—do not use in the vicinity of flammable anaesthetics.
If oxygen is used with this device, the oxygen flow must be turned off when the
device is not operating.
If oxygen has been left on, turn off the flow generator, then wait 30 minutes before
turning on the flow generator again.
Explanation: When the CPAP device is not in operation and the oxygen flow is
left on, oxygen delivered into the air delivery tubing may accumulate within the
CPAP machine enclosure and create a risk of fire. This applies to most types of
CPAP machines.
Oxygen supports combustion. Oxygen should not be used while you are
smoking or in the presence of an open flame.
Always ensure airflow is being generated by the device before the oxygen
supply is turned on.
Always turn the oxygen supply off before stopping the airflow from the device.
Note: At a fixed rate of supplemental oxygen flow, the inhaled oxygen concentration
will vary, depending on where the oxygen is introduced, the pressure settings, patient
breathing pattern, mask selection and leak rate.
COMPONENTS OF YOUR HUMIDAIRE 3i
Please refer to the illustrations in section A of the illustration sheet.
SETTING UP YOUR HUMIDAIRE 3i FOR USE
!
WARNING
Make sure your flow generator is switched off at the power outlet before
connecting the HumidAire 3i.
REMOVING THE FRONT CAP (IF FITTED)
Please refer to the illustrations in section B of the illustration sheet.
Your flow generator may be fitted with a front cap (B-1). Before you can attach the
H
UMIDAIRE 3i, press the button underneath the front cap (B-2) and pull it away from
the body of your flow generator (B-3 & B-4).
33804r2.book Page 5 Wednesday, May 25, 2005 2:54 PM
6
Notes
To replace the front cap, align it with your flow generator (B-4) and push it firmly until it
clicks into place.
Remember to take the front cap with you when travelling, in case you need CPAP
therapy without a humidifier.
REMOVING AND STORING THE CONNECTOR PLUG
Please refer to the illustrations in section C of the illustration sheet.
Before attaching the H
UMIDAIRE 3i, remove the connector plug from your flow
generator (C-1) and attach it to the back of the docking station (C-2).
ATTACHING YOUR HUMIDAIRE 3i
Please refer to the illustrations in section D of the illustration sheet.
1 Align your HUMIDAIRE 3i with your flow generator (D-1) and push them together
until they click into place (D-2).
!
WARNING
The HumidAire 3i docking station should only be connected or disconnected
when the water chamber is empty.
Water must be prevented from entering your flow generator. Do not transport
the flow generator with the HumidAire 3i attached.
2
Insert the power cord into the socket at the rear of your flow generator. Plug the other
end of the power cord into a power outlet (D-3).
Note: If your flow generator is powered via the DC input, the HumidAire 3i is not powered
and humidification output will be reduced.
3
Place the combined unit on a firm, level surface near your bed at a level lower than
your sleeping position. Ensure the surface is not sensitive to heat and/or moisture, or
use a protective mat.
!
CAUTION
Be careful not to place the unit where it can be bumped into and knocked over.
4
Connect one end of the air tubing firmly onto the air outlet of your HUMIDAIRE 3i
and the other end to your mask (D-4).
FILLING THE WATER CHAMBER
Please refer to the illustrations in section E of the illustration sheet.
!
WARNING
Take care when handling your HumidAire 3i. The water and the water chamber
base may both be hot. Allow ten minutes for the heater plate and any excess water
to cool.
1 Release the cover latch (E-1) and lift the cover until it rests in the upright position (E-2).
33804r2.book Page 6 Wednesday, May 25, 2005 2:54 PM
7
STARTING AND STOPPING TREATMENT
ENGLISH
2
Remove the water chamber (E-3) and carefully fill it with fresh, clean water (E-4). Make
sure you keep the level of the water under the maximum water level mark (E-4a).
Always ensure that the water chamber is clean. See “Cleaning and Maintenance” on
page 10.
!
WARNING
Do not overfill the water chamber, as water may enter your flow generator and air
tubing.
!
CAUTION
Do not use any additives (eg scented oils and perfumes). They may reduce the
humidification output of the HumidAire 3i and/or cause deterioration of the water
chamber materials.
3
Carefully place the filled water chamber into the humidifier docking station (E-5) and
latch the cover (E-6 & E-6a).
The H
UMIDAIRE 3i is now ready for use.
STARTING AND STOPPING TREATMENT
STARTING YOUR TREATMENT
Please refer to the illustration in section F of the illustration sheet.
1 When your HUMIDAIRE 3i is attached and the flow generator is powered, the
indicator light lights up on the H
UMIDAIRE 3i. A prompt for the Warm-Up feature
(not available on all models) may appear.
When activated, this feature allows the water to warm up before you start treatment.
2
If the Warm-Up feature is available, use it to pre-heat the water before starting your
treatment. Skip this step if you wish to start treatment immediately.
WARM-UP FEATURE (NOT AVAILABLE IN ALL MODELS)
Note: Check your flow generator user’s manual to see if this feature is available.
To start the Warm-Up feature:
i. Select Warmup by pressing the Right key on the control panel.
The following message is displayed for 2 seconds:
ii. After 2 seconds the WARMING screen is displayed.
RAMP: 10min
menu
warmup
HUMIDIFIER
WARMING
WARMING
menu exit
33804r2.book Page 7 Wednesday, May 25, 2005 2:54 PM
8
iii. While your HUMIDAIRE 3i is in Warm-Up mode you can:
Start treatment at any time by pressing the Start/Stop key.
Access the menus by pressing Menu (Left key).
Stop the Warm-Up feature at any time by pressing Exit (Right key).
The Warm-Up feature will automatically turn off after 30 minutes if treatment has not
started.
3
Turn the humidity control dial to the desired setting. The setting switches heated
humidification off and delivers minimum humidification. The indicator light will remain
lit to indicate standby mode. A setting of 6 ( ) delivers maximum humidification.
We recommend that you initially set the control dial to 3 ( ). If necessary, adjust the
control dial up or down to find the setting that is most comfortable and effective for
you. You can adjust the humidity setting at any time.
The aim is to have moist air delivered to your mask but to avoid condensation forming
in the air tubing. The temperature and humidity of the surrounding air will affect the
setting you need.
See “Frequently Asked Questions” for further tips on the correct humidity setting.
4
Fit your mask as described in your mask user instructions.
5
Press the Start/Stop key on the control panel. Alternatively, if your flow generator
has the SmartStart™ function available, simply breathe into your mask and air should
begin to flow.
Note: During operation, the indicator light becomes brighter to indicate that the heating
element is active. Your HumidAire 3i has a rapid heating element which allows very short
heating times. Do not be concerned if the light only brightens very briefly.
6
Lie down and arrange the air tubing so that it is free to move if you turn in your sleep.
!
WARNING
Do not leave an excessive length of air tubing around the top of your bed. It could
twist around your head or neck while you are sleeping.
STOPPING YOUR TREATMENT
To stop your treatment at any time, remove your mask and press the Start/Stop key.
Alternatively, if your flow generator has the SmartStart function available, simply
remove your mask and treatment will end.
Some flow generators continue to blow air gently after you have stopped your
treatment. This can continue for up to one hour to assist the heater plate in cooling.
However, you can unplug the device from the power outlet at any time and allow the
heater plate to cool without airflow.
DETACHING YOUR HUMIDAIRE 3i
Please refer to the illustrations in section G of the illustration sheet.
33804r2.book Page 8 Wednesday, May 25, 2005 2:54 PM
9
FREQUENTLY ASKED QUESTIONS
ENGLISH
1 Unplug the power cord from the power outlet (G-1).
!
WARNING
Take care when handling your HumidAire 3i. The water and the water chamber
base may both be hot. Allow ten minutes for the heater plate and any excess water
to cool (G-2).
2
Remove the water chamber from the docking station (G-3).
3
Press the large silver button located midway underneath the docking station
(G-4) and pull the H
UMIDAIRE 3i and flow generator apart (G-5).
Note: Re-attach the connector plug firmly to your flow generator.
FREQUENTLY ASKED QUESTIONS
WHY IS THERE CONDENSATION IN MY MASK AND/OR AIR TUBING?
You may experience excessive condensation in your mask or air tubing. This may occur
seasonally, particularly when the room temperature is low or cool air is circulating
around the tube. Turn the control dial down to a lower setting until the condensation
decreases.
You may have to adjust your humidity setting from season to season.
DO I HAVE TO USE DISTILLED WATER IN THE WATER CHAMBER?
Using distilled water will maximise the life of the water chamber and reduce mineral
deposits. See “Cleaning your HumidAire 3i” on page 11 for further details.
WHAT IF I STILL HAVE SYMPTOMS OF DRYNESS?
If you still experience symptoms of dryness, then your humidity setting may be set too
low to be effective. Gradually turn the humidity control dial up over a few nights until
the symptoms disappear.
If you are still experiencing symptoms of dryness, even after increasing the humidity
setting, you may be breathing through your mouth. Mouth breathing or mouth leaks
cause drying and irritation of the upper airway. If this is a problem, a full face mask or
chin strap may help. Consult your clinician or equipment supplier for details.
Large silver button
UNDERSIDE VIEW
33804r2.book Page 9 Wednesday, May 25, 2005 2:54 PM
10
CLEANING AND MAINTENANCE
You should regularly carry out the cleaning and maintenance of the water chamber,
cover and cover seal as described in this section.
DISASSEMBLING YOUR HUMIDAIRE 3i
Please refer to the illustrations in section H of the illustration sheet.
!
WARNING
Beware of electrocution. Do not immerse your flow generator, docking station or
power cord in water. Always unplug the device before cleaning and be sure that it
is dry before plugging it back in.
1 Unplug the power cord from the power outlet (H-1).
!
WARNING
Take care when handling your HumidAire 3i. The water and the water chamber
base may both be hot. Allow ten minutes for the heater plate and any excess water
to cool (H-2).
2
Remove the water chamber from the docking station (H-3) and discard any excess
water (H-4).
3
Detach the air tubing from the air outlet (H-5).
4
Gently flex one cover arm away and up from the docking station until the cover
detaches completely (H-6 to H-8). Peel the cover seal away from the cover (H-9).
TUB PLATE
The tub plate should not be removed from the water chamber. If removed, replace
the tub plate by:
i. Turning the water chamber base upside down.
ii. As shown below, position the tub plate so that the open side is facing down. Then
firmly press the tub plate down into the water chamber.
!
CAUTION
The water chamber may leak if the tub plate is refitted incorrectly.
Note: The tub plate will not fit into the water chamber if it is facing up. Before fitting the
tub plate, make sure the O-ring is fitted snugly inside the groove of the tub plate.
tub plate
33804r2.book Page 10 Wednesday, May 25, 2005 2:54 PM
11
CLEANING AND MAINTENANCE
ENGLISH
CLEANING YOUR HUMIDAIRE 3i
!
CAUTION
Do not use any of the following to clean any part of the HumidAire 3i. These
solutions may cause damage and reduce the life of the product.
bleach, chlorine-, alcohol- or ammonia-based solutions
moisturising, antibacterial or glycerine based soaps
water softening and unapproved descaling agents.
Do not wash the water chamber in a dishwasher.
WATER CHAMBER
DAILY
Wash the water chamber and tubing in warm water, using a mild detergent
(see previous caution). Rinse them thoroughly with clean water and allow them to dry
away from direct sunlight.
WEEKLY
Inspect the water chamber for wear and deterioration. Replace the water chamber if
any component has cracked, become cloudy or pitted. Replace immediately if there is
any leaking from the water chamber.
If you notice white powder or deposits in the water chamber:
i. Fill the water chamber to the maximum water level mark with a solution of one
part vinegar to ten parts water.
ii. Let the solution soak for ten minutes.
iii. Discard the solution and rinse the water chamber with clean water.
COVER AND COVER SEAL
Inspect the cover and cover seal weekly for wear and deterioration. Replace any
damaged parts. When required, wash the cover and cover seal in warm water, using a
mild detergent (see previous caution). Rinse them thoroughly with clean water and
allow them to dry away from direct sunlight.
DOCKING STATION
Periodically wipe the outside of the docking station (including the connector seal) with
a damp cloth.
REASSEMBLING YOUR HUMIDAIRE 3i
Please refer to the illustrations in section I of the illustration sheet.
Reassemble the parts when they are clean and dry.
1 Align the cover seal to the guides on the cover (I-1) and press along the edges to
ensure it is fitted properly (I-2).
2
Put one cover arm into its pivot point on the docking station (I-3) and gently flex the
other arm into its corresponding point (I-4 & I-5).
33804r2.book Page 11 Wednesday, May 25, 2005 2:54 PM
12
The cover should be able to open and close freely while securely attached to the
docking station.
3
Replace the water chamber in the humidifier docking station (I-6).
SERVICING
With normal use of a HUMIDAIRE 3i, the water chamber needs to be replaced every
two years.
This product (H
UMIDAIRE 3i) should be inspected by an authorised ResMed Service
Centre 5 years from the date of manufacture. Prior to this, the device is intended to
provide safe and reliable operation provided that it is operated and maintained in
accordance with the instructions provided by ResMed. Applicable ResMed warranty
details are provided with the device at the time of original supply. Of course, as with
all electrical devices, if any irregularity becomes apparent, you should exercise caution
and have the device inspected by an authorised ResMed Service Centre.
33804r2.book Page 12 Wednesday, May 25, 2005 2:54 PM
13
TROUBLESHOOTING
ENGLISH
TROUBLESHOOTING
If there is a problem, try the following suggestions. If the problem cannot be solved,
contact your equipment supplier or ResMed. Do not attempt to open the unit.
!
WARNING
Service and repair should only be performed by an authorised service agent.
Problem Possible Cause Solution
Device not working
(no display on LCD
screen and/or
indicator light not
lighting up)
Power cord is not plugged
in properly.
Faulty power outlet.
Flow generator and
docking station not
connected correctly.
Check that the power cord is plugged
firmly into the power outlet and the
switch (if available) is on at the outlet.
Try another power outlet.
Check that the docking station is
securely attached to the flow generator.
Indicator light
flickering
Indicator light periodically
becomes brighter to
indicate that the heating
element is active.
Your HumidAire 3i has a rapid
heating element which allows very
short heating times. Do not be
concerned if the light only brightens
very briefly.
Turn the dial to the setting to
switch heated humidification off. The
indicator light will remain lit to
indicate standby mode.
Indicator light is
permanently dull
and/or air does not
feel warm
HumidAire 3i reflector (see
illustration C-2a) is dirty.
Clean the reflector with a damp cloth.
Leaking water
chamber
The water chamber may be
damaged or cracked.
Cover is not attached
correctly.
Contact your supplier for a replacement.
Make sure the cover is fitted correctly.
33804r2.book Page 13 Wednesday, May 25, 2005 2:54 PM
14
No/low air flow The air tubing is not
connected properly.
The air tubing is blocked,
pinched or punctured.
The flow generator is not
working correctly.
The water chamber is
overfilled.
The cover is not latched
correctly.
The cover seal is not fitted
correctly.
Condensation is forming in
the air tube.
Connect the air tubing as described in
“Setting Up your HumidAire 3i For Use”
on page 5.
Unblock or free the air tubing. Check the
air tubing for punctures.
See the Troubleshooting section in the
flow generator manual.
Make sure that the water level is not
above the maximum water level mark.
Make sure the cover is latched onto the
docking station correctly.
Make sure the cover seal is facing the
right way up and fitted securely.
Turn the control dial down.
Insulate the air tubing.
Water splashing on
your face
The water chamber is
overfilled.
Condensation is forming in
the air tube and mask.
Empty some water from the water
chamber.
Turn the control dial down.
Insulate the air tubing.
Air does not feel
moist
The control dial is set too
low.
HumidAire 3i heating
element is not working.
Turn the control dial up.
Contact your equipment supplier.
Air too moist Control dial is set too high.
High relative humidity in
your room.
Turn the control dial down.
Adjust your humidity setting.
White powder or
deposits in the water
chamber
The water leaves scaly
mineral deposits.
Use distilled water.
To remove these mineral deposits, see
“Cleaning your HumidAire 3i” on
page 11.
Problem Possible Cause Solution
33804r2.book Page 14 Wednesday, May 25, 2005 2:54 PM
15
TECHNICAL SPECIFICATIONS
ENGLISH
TECHNICAL SPECIFICATIONS
PERFORMANCE
Maximum heater plate temperature: 85°C
Temperature cut-out: 93°C
Maximum output humidity: 95% relative humidity (control dial set to maximum setting,
flow rate 50 L/min, ambient temperature of 20°C, ambient relative humidity of 40%).
Maximum gas temperature: 41°C
DIMENSIONS (H X W X D)
Docking station and water chamber: 118 mm x 170 mm x 212 mm
WEIGHT
Docking station and unfilled water chamber: 670 g
Water capacity to maximum fill line: 385 mL
POWER SUPPLY
Input range for RESMED S8 flow generator with HUMIDAIRE 3i: 100–240V, 50/60Hz;
110V, 400Hz; 2.5A <140 VA (110 W) (maximum power consumption). Instantaneous
peak power consumption <340 VA.
Actual average power consumption will vary, depending on factors such as
temperature setting, set pressure, the use of accessories, height above sea level and
ambient temperature.
Maximum heater element power: 85 W.
HOUSING CONSTRUCTION
Docking station: Flame retardant engineering thermoplastic, plated cast aluminium.
Water chamber: Injection molded plastic, stainless steel.
ENVIRONMENTAL CONDITIONS
Operating temperature: +5°C to +40°C
Operating humidity: 10–95% non-condensing
Storage and transport temperature: -20°C to +60°C
Storage and transport humidity: 10–95% non-condensing
IEC 60601-1 CLASSIFICATION
Class II (double insulation)
Type CF
ELECTROMAGNETIC COMPATIBILITY
Please refer to your flow generator user's manual for details.
Note: The manufacturer reserves the right to change these specifications without notice.
33804r2.book Page 15 Wednesday, May 25, 2005 2:54 PM
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109

ResMed HumidAire 3i Användarmanual

Kategori
Avfuktare
Typ
Användarmanual
Denna manual är också lämplig för