Yamaha YHT-S300 Bruksanvisning

varumärke: Yamaha

Modell: YHT-S300

Kategori: AV-mottagare

Typ: Bruksanvisning

Home Theater Package

(Subwoofer Integrated Receiver + Speaker)

YHT-S300

(SR-300 + NS-B380)

Owner’s Manual

English

2 En

1 To assure the finest performance, please read this

manual carefully. Keep it in a safe place for future

reference.

2 Install this unit in a well ventilated, cool, dry, clean

place - away from direct sunlight, heat sources,

vibration, dust, moisture, and/or cold. For proper

ventilation, allow the following minimum clearances.

Top: 5 cm (2 in)

Rear: 5 cm (2 in)

Sides: 5 cm (2 in)

3 Locate this unit away from other electrical appliances,

motors, or transformers to avoid humming sounds.

4 Do not expose this unit to sudden temperature changes

from cold to hot, and do not locate this unit in an

environment with high humidity (i.e. a room with a

humidifier) to prevent condensation inside this unit,

which may cause an electrical shock, fire, damage to

this unit, and/or personal injury.

5 Avoid installing this unit where foreign objects may fall

onto this unit and/or this unit may be exposed to liquid

dripping or splashing. On the top of this unit, do not

place:

– Other components, as they may cause damage and/or discoloration

on the surface of this unit.

– Burning objects (i.e. candles), as they may cause fire, damage to

this unit, and/or personal injury.

– Containers with liquid in them, as they may fall and liquid may

cause electrical shock to the user and/or damage to this unit.

6 Do not cover this unit with a newspaper, tablecloth,

curtain, etc. in order not to obstruct heat radiation. If the

temperature inside this unit rises, it may cause fire,

damage to this unit, and/or personal injury.

7 Do not plug in this unit to a wall outlet until all

connections are complete.

8 Do not operate this unit upside-down. It may overheat,

possibly causing damage.

9 Do not use force on switches, knobs and/or cords.

10 When disconnecting the power cable from the wall

outlet, grasp the plug; do not pull the cable.

11 Do not clean this unit with chemical solvents; this might

damage the finish. Use a clean, dry cloth.

12 Only voltage specified on this unit must be used. Using

this unit with a higher voltage than specified is

dangerous and may cause fire, damage to this unit, and/

or personal injury. Yamaha will not be held responsible

for any damage resulting from use of this unit with a

voltage other than specified.

13 To prevent damage by lightning, keep the power cable

and outdoor antennas disconnected from a wall outlet or

the unit during a lightning storm.

14 Do not attempt to modify or fix this unit. Contact

qualified Yamaha service personnel when any service is

needed. The cabinet should never be opened for any

reasons.

15 When not planning to use this unit for long periods of

time (i.e. vacation), disconnect the AC power plug from

the wall outlet.

16 Be sure to read the “Troubleshooting” section on

common operating errors before concluding that this

unit is faulty.

17 Before moving this unit, press to set this unit in

standby mode, and disconnect the power supply cable

from the wall outlet.

18 Condensation will form when the surrounding

temperature changes suddenly. Disconnect the power

supply cable from the outlet, then leave the unit alone.

19 Install this unit near the wall outlet and where the AC

power plug can be reached easily.

20 The batteries shall not be exposed to excessive heat such

as sunshine, fire or like.

21 Secure placement or installation is the owner’s

responsibility. Yamaha shall not be liable for any

accident caused by improper placement or installation of

speakers.

■ For U.K. customers

If the socket outlets in the home are not suitable for

the plug supplied with this appliance, it should be cut

off and an appropriate 3 pin plug fitted. For details,

refer to the instructions described below.

The plug severed from the mains lead must be destroyed, as

a plug with bared flexible cord is hazardous if engaged in a

live socket outlet.

■ Special Instructions for U.K. Model

Caution: Read this before operating your unit.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC

SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN

OR MOISTURE.

As long as this unit is connected to the AC wall

outlet, it is not disconnected from the AC power

source even if you turn off this unit by . In this

state, this unit is designed to consume a very small

quantity of power.

Note

IMPORTANT

THE WIRES IN THE MAINS LEAD ARE

COLOURED IN ACCORDANCE WITH THE

FOLLOWING CODE:

Blue: NEUTRAL

Brown: LIVE

As the colours of the wires in the mains lead of this

apparatus may not correspond with the coloured

markings identifying the terminals in your plug,

proceed as follows:

The wire which is coloured BLUE must be

connected to the terminal which is marked with the

letter N or coloured BLACK. The wire which is

coloured BROWN must be connected to the

terminal which is marked with the letter L or

coloured RED.

Making sure that neither core is connected to the

earth terminal of the three pin plug.

INTRODUCTION PREPARATION

BASIC

OPERATION

USEFUL

OPERATION

ADDITIONAL

INFORMATION

3 En

INTRODUCTION

Getting started....................................................4

Supplied parts........................................................ 4

Controls and functions ..........................................5

PREPARATION

Placing .................................................................8

Placing the speakers.............................................. 8

Connection ........................................................10

Overview............................................................. 10

Connecting a TV ................................................. 11

Connecting Blu-ray disc player or

set-top box ....................................................... 11

BASIC OPERATION

Basic playback operation.................................12

Enjoying sound modes .....................................13

Surround mode.................................................... 13

Stereo mode ........................................................ 13

UniVolume™...................................................... 13

Listening to FM broadcasts.............................14

Basic tuning operation ........................................ 14

Editing the preset FM station .............................. 14

Using optional equipment................................16

Connecting dock ................................................. 16

Using iPod™....................................................... 16

Using Bluetooth™ components .......................... 17

USEFUL OPERATION

Setup menu ....................................................... 18

Overview .............................................................18

Basic procedure...................................................18

Adjusting the volume balance during

playback...........................................................19

Adjusting high/low frequency sound

(tone control)....................................................19

Adjusting the audio delay....................................19

Setting the audio output ......................................19

Switching on/off the HDMI™ control

function ............................................................19

Changing the brightness of the front panel

display..............................................................20

Changing the setting of the speaker type ............20

Setting the distance between the speakers ..........20

Using the HDMI™ control function ...................21

ADDITIONAL INFORMATION

Additional information.................................... 22

Troubleshooting ..................................................22

Glossary...............................................................25

Specifications ......................................................27

Available signal information...............................28

Contents

■ About this manual

• In this manual, operations that can be performed using either the front panel buttons or the remote control are

explained using the remote control.

• y indicates a tip for your operation. Notes contain important information about safety and operating

instructions.

• This manual is produced prior to production. Design and specifications are subject to change in part as a result

of improvements, etc. In case of differences between the manual and the product, the product has priority.

4 En

INTRODUCTION

This product consists of the following items. Before making connections, make sure you have received all of the

following items.

■ Units

■ Accessories

■ Installing the batteries

Getting started

Supplied parts

Subwoofer Integrated Receiver (SR-300) Speakers (NS-B380)

Speaker cable (3 m × 2) Remote control Indoor FM antenna

(Asia model) (Europe and Russia

models)

Stand × 2

(for speaker)

Battery × 2 (AAA, R03, UM4) Screw × 2

(for stand)

CD-ROM

(Owner’s Manual)

Quick Reference

Guide

• If the effective operation distance of the remote control decreases considerably, replace

the batteries with two new ones as soon as possible.

• Do not use an old battery together with new one.

• Do not use different types of batteries (for example, alkaline and manganese) together.

Their performance will vary, even if they are similar in shape.

• If the batteries run out, immediately remove them from the remote control to prevent an

explosion or acid leak.

• Dispose of batteries according to regional regulations.

• If a battery starts leaking, dispose of it immediately. Be careful not to let leaking battery

acid come into contact with your skin or clothing. Before inserting new batteries, wipe

the compartment clean.

Notes

5 En

Getting started

INTRODUCTION

■ Front panel of the subwoofer integrated receiver

Turns on the system, or sets it to standby mode.

(☞ P. 12)

A small amount of electricity is consumed to receive

the infrared signal from the remote control even when

the system is in standby mode.

2 STATUS indicator

Lights up to show the system condition. (☞ P. 12)

3 INPUT

Selects an input source you want to listen to.

(☞ P. 12)

4 VOLUME –/+

Controls the volume of the system. (☞ P. 12)

5 Remote control sensor

Receives infrared signals from the remote control.

(☞ P. 7, 10)

6 Front panel display

Shows information about the operational status of

the system. (☞ P. 12)

■ Rear panel of the subwoofer integrated receiver

1 Power Cable

For connecting an AC wall outlet. (☞ P. 10)

2 HDMI IN 1 - 3/HDMI OUT

• HDMI IN 1 - 3 for connecting HDMI

compatible external components. (☞ P. 11)

• HDMI OUT for connecting an HDMI

compatible TV. (☞ P. 11)

3 DIGITAL IN jack

For connecting optical digital cable to the TV.

(☞ P. 11)

4 ANALOG INPUT jack

For connecting analog audio cable to external

components. (☞ P. 10)

5 DOCK terminal

For connecting an optional Yamaha iPod universal

dock (such as YDS-11, sold separately) or

Bluetooth wireless audio receiver (such as YBA-

10, sold separately). (☞ P. 16)

6 ANTENNA terminal

For connecting supplied FM antenna. (☞ P. 10)

7 SPEAKERS terminal

For connecting speakers. (☞ P. 10)

Controls and functions

1 2 3 4 5 6

Note

1 2

7 6 5 4 3

Getting started

6 En

■ Front panel display of the subwoofer integrated receiver

1 HDMI indicator

Lights up during normal communication when

HDMI is selected as an input source.

2 Tuner indicators

TUNED indicator

Lights up when the system is receiving a station.

(☞ P. 14)

STEREO indicator

Lights up when the system is receiving a strong

signal from an FM stereo broadcast station in

automatic tuning mode. (☞ P. 14)

AUTO indicator

Flashes when the system is tuning station

automatically. (☞ P. 14)

MEMORY indicator

Flashes when the system is storing a station.

(☞ P. 14, 15)

EMPTY indicator

Lights up when the storing preset number is empty.

(☞ P. 15)

PS/PTY/RT/CT indicator (Europe and

Russia models only)

Lights up according to the available Radio Data

System information. (☞ P. 15)

3 Decoder indicators

The respective indicator lights up when any of the

decoders of the system is activated.

4 DOCK indicator

• Lights up when the system is receiving a signal

from an iPod stationed in the Yamaha iPod

universal dock (such as YDS-11, sold

separately) connected to the DOCK terminal of

the subwoofer integrated receiver. (☞ P. 16)

• Lights up while the Yamaha Bluetooth wireless

audio receiver (such as YBA-10, sold

separately) is connected to the Bluetooth

component. (☞ P. 17)

• Flashes while the connected Yamaha Bluetooth

wireless audio receiver (such as YBA-10, sold

separately) and the Bluetooth component are

pairing (☞ P. 17) or while the Yamaha

Bluetooth wireless audio receiver is searching

for the Bluetooth component. (☞ P. 17)

5 VOLUME indicator

• Indicates the current volume level.

• Flashes while the mute function is activated.

(☞ P. 12)

6 Multi information display

Shows the selected input source, current sound

mode and other information.

7 ENHANCER indicator

Lights up when compressed music enhancer

function is activated. (☞ P. 16)

8 UNIVOLUME indicator

Lights up when UniVolume mode is selected.

(☞ P. 13)

1 2 3 4

7 En

Getting started

INTRODUCTION

■ Remote control

1 Input buttons

Select an input source you want to listen to.

(☞ P. 12)

2 MEMORY, TUNING / , PRESET / ,

INFO

Control an FM tuner. (☞ P. 14)

3 OPTION

Enters OPTION menu when operating FM

function or using Bluetooth component. (☞ P. 14,

17)

4 (MENU) / ( ) / ( ) / ( ) /

(Center)

• Change the setting.

• Control an iPod. (☞ P. 16)

S / T: Control the wheel of iPod.

5 RETURN

Returns to the previous menu or cancels preset

registration/pairing operation.

6 SUBWOOFER (+/–)

Adjust the volume balance of subwoofer.

(☞ P. 19)

7 SURROUND MODE

Selects the surround mode. (☞ P. 13)

8 STEREO MODE

Turns extended stereo mode on and off alternately.

(☞ P. 13)

9 UNIVOLUME

Turns UniVolume mode on and off. (☞ P. 13)

0 VOLUME (+/–)/MUTE

Control the volume of the system. (☞ P. 12)

A SETUP

Enters the setup menu. (☞ P. 18)

Turns on the system, or sets it to standby mode.

(☞ P. 12)

Infrared signal

transmitter

8 En

PREPARATION

To enjoy quality sound thoroughly, place this system in the appropriate positions, and install the components

properly. The following illustrations are the setting images of this system.

Example 1 : Placing the speakers on the rack Example 2 : Mounting the speakers on the wall

1 Subwoofer integrated receiver (SR-300)

2 Speakers (NS-B380)

• Do not place this system on/under any other components such as Blu-ray disc player in a pile. The vibration of this system

may cause system failure, etc. in other components.

• Keep enough ventilation space on the front, rear, and bottom side (that attached legs) of this system. Do not place this

system on a thick carpet etc.

• If the picture on your CRT TV screen becomes blurred or distorted, we recommend moving the system away from your TV.

• Low frequency sound produced by the subwoofer integrated receiver may be heard differently depending on the listening

position and subwoofer location. To enjoy desired sounds, try changing the location of the subwoofer integrated receiver.

• Depending on your installation environment, connections to external components can be done before installing this system.

We recommend that you temporarily place and arrange all components in order to decide which procedure is best done first.

• Set the distance between the speakers to increase surround effect. (☞ P. 20)

You can place the speakers on a rack or attach it to a wall. Select an installation method that suits your environment.

■ Placing the speakers using the stands

You can place the speakers in an upright position or a horizontal position.

When placing the speakers in an upright

position

Place the speaker on the stand vertically, and then secure

it with the screw as shown in the illustration below.

When placing the speakers in a horizontal

position

Place the speaker on the stand horizontally, and then

secure it with the screw as shown in the illustration

below.

Placing

Notes

Placing the speakers

9 En

Placing

PREPARATION

■ Attaching the speakers to a wall

Installing the speakers using the keyholes

You can attach the speakers to a wall using

commercially available screws (#8, Diameter: 7 to 9

mm (1/4” to 3/8”)).

1 When placing the speakers on a wall,

remove the stands.

2 Install screws on a wall as shown in the

illustration.

The distance between the screws: 150

mm (5-7/8”) for both sides

3 Hang the speakers on the screws using

the keyholes on the back of the speakers.

• Do not attach the speakers to a wall that is made of weak

materials such as plaster or veneered woods. Doing so

may cause the speakers to fall.

• Use commercially available screws that can support the

weight of the installation.

• Make sure you use specified screws to attach the speakers.

Using clamps other than specified screws, such as short

screws, nails, or two-sided tape, may cause the speakers to

fall.

• When connecting the speakers, fix the speaker cables in

place where they will not become loose. If your foot or

hand accidentally gets caught on a loose speaker cable, the

speakers may fall.

• After attaching the speakers, check that the speakers are

fixed securely. Yamaha will bear no responsibility for any

accidents caused by improper installations.

When installing the speakers on a wall, all

installation work must be performed by a

qualified contractor or dealer. The customer

must never attempt to perform this installation

work. Improper or inadequate installation could

cause the speakers to fall, resulting in personal

injury.

Minimum

20 mm (3/4”)

6 mm

(1/4”)

150 mm

(5-7/8”)

Wall/wall

support

Vertical

Horizontal

150 mm

(5-7/8”)

Diameter: 7 to 9 mm

(#8, 1/4” to 3/8”)

Notes

10 En

Follow the procedure below to connect the subwoofer integrated receiver and the external components.

Connect your speaker as the center speaker of this system to the SPEAKERS terminal of the subwoofer integrated

receiver. (☞ P. 20)

Connection

• Do not connect the power cable until all connections are completed.

• Do not use excessive force when inserting the cable plug. Doing so may damage the cable plug and/

or terminal.

Overview

See “Connecting Blu-ray disc player or set-top

box”. (☞ P. 11)

Indoor FM antenna (supplied)

If the radio wave reception is weak in your area

or you want to improve the radio wave reception,

we recommend that you use an outdoor antenna.

For details, consult your nearest authorized

Yamaha dealer or Service Center.

See “Using optional

equipment”. (☞ P. 16)

To AC wall outlet

See “Connecting a TV”. (☞ P. 11)

Twist and pull off the

insulation tube on the

lead wire.

VCR, etc.

Insert to the terminal of the

correct polarity—positive

(+) to positive (+), and

negative (–) to negative (–).

White

Gray

After you have made all connections, connect the

power cable of the subwoofer integrated receiver.

Front Right

Speaker

Front Left

Speaker

11 En

Connection

PREPARATION

If a DVD player, etc., is connected to one of the HDMI IN jacks, connect your TV or video monitor (projector,

etc.) to the HDMI OUT jack of the subwoofer integrated receiver.

To output the sound of a TV from this system, you can select optical digital input and connect to digital output

jack.

For analog connection, you need to connect an audio cable to the analog input terminal.

You can connect external components with HDMI output. You can select from HDMI IN 1, 2, or 3. These

three jacks are identical.

Connecting a TV

Signal flow

Connecting Blu-ray disc player or set-top box

Blu-ray disc player or

set-top box

12 En

BASIC OPERATION

Once you have finished all cable connections and remote control operation, follow the procedure below to start

basic playback operation.

1 Press .

This system is turned on and the STATUS

indicator lights green.

This system has the auto-sleep function, which will

automatically switch the system to turn off if the

system is left turned on for 24 hours without any

operation being performed.

2 Press one of the input buttons to select

an input source.

3 Start playback on the selected external

component.

For information on the external component, refer

to the instruction manual for the product.

4 Press VOLUME +/– to adjust the volume

level.

To turn off the volume temporarily, press MUTE.

While the mute function is activated, the VOLUME

indicator flashes. To resume the volume, press MUTE

again or press VOLUME +/–.

When sound of HDMI is output from the TV, the

volume level does not change if you press VOLUME

+/–.

■ Using the remote control

Basic playback operation

Note

Press again to set the system to

standby mode.

When the “HDMI CONTROL” is set to “ON”, the

STATUS indicator lights red. When the “HDMI

CONTROL” is set to “OFF”, the STATUS indicator

turns off. (☞ P. 19)

Within 6 m (20’)

Use the remote control within 6 m (20’) of the

subwoofer integrated receiver and point it toward the

remote control sensor.

• Be careful not to spill liquid on the remote control.

• Be careful not to drop the remote control.

• Do not leave the remote control in a place that is:

– hot or humid, such as near a heater or in a bathroom

–extremely cold

–dusty

Notes

BASIC

OPERATION

13 En

You can enjoy a realistic sound effect using Yamaha’s

exclusive AIR SURROUND XTREME.

Press SURROUND MODE to set

surround mode.

Press SURROUND MODE repeatedly until desired

mode appears in the front panel display.

Surround mode descriptions

The system automatically memorizes the settings assigned

to each input source. When you select another input, the

system automatically recalls the last settings for the selected

input.

An extended sound is achieved for a 2 channel source

such as a CD player.

Press STEREO MODE to enter extended

stereo mode.

Each time you press STEREO MODE, the function is

turned on (EXTENDED STEREO) and off (STEREO)

alternately.

“STEREO”: Reproduces the sound without any effect.

“EXTENDED STEREO”: Reproduces a wider stereo

image.

• The default setting is “EXTENDED STEREO”.

• The system memorizes the settings assigned to each input

source.

While watching TV, use this function when you feel

uncomfortable with the difference in volume between

channels, TV programs, and commercials to keep the

volume at an even level.

Press UNIVOLUME to activate or

deactivate the function.

When UniVolume is activated, UNIVOLUME

indicator is displayed and the sound volume of TV is

uniformed.

• The system memorizes the setting assigned to each input

source.

• When the input source is DOCK and UniVolume is

activated, compressed music enhancer function is invalid

(ENHANCER indicator disappears).

Enjoying sound modes

SURROUND MODE

STEREO MODE

UNIVOLUME

Surround mode

MOVIE This mode is useful when you enjoy

movie contents on media such as

Blu-ray disc, etc.

MUSIC This mode is useful when you listen to

music contents on media such as

Blu-ray disc, etc.

SPORTS This mode is useful when you enjoy

sports programs or TV news.

GAME This mode is useful when you enjoy

video games.

Stereo mode

UniVolume™

14 En

■ Automatic preset

You can store up to 40 FM stations (01 to 40).

1 Press OPTION to enter OPTION menu.

“AUTO PRESET” appears firstly in the front

panel display.

2 Press (Center).

Press PRESET / repeatedly to select a preset

number to which the first station will be stored.

After approximately 5 seconds, automatic

presetting starts from the lowest frequency and

proceeds through higher frequencies. When the

frequency is stored, the TUNED indicator lights

up.

When automatic preset tuning is completed, the front

panel display shows message “Preset Complete” for

three seconds firstly and returns to OPTION menu

secondly.

Press RETURN while searching automatically, automatic

preset is stopped.

• Any stored station data existing under a preset number is

cleared when you store a new station under the same

preset number.

• If the number of received stations does not reach 40,

automatic preset tuning automatically stops after

searching for all the available stations.

• Only the station with strong signals can be stored. If the

desired station is not stored, or a station is not stored to the

desired preset number, preset the station manually.

(☞ P. 15)

Listening to FM broadcasts

Basic tuning operation

Editing the preset FM station

Sets the input to FM.

TUNING /

Press to change the frequency

by 1 step, or press and hold to

search stations automatically.

PRESET /

Select the preset FM

stations.

INFO

Selects the information

displayed in the front panel

display.

OPTION

Enters OPTION menu

when the input is set to FM.

Cursor in OPTION

MEMORY

Stores preset stations

manually.

RETURN

Returns to the previous

menu or cancels the

operation.

Notes

15 En

Listening to FM broadcasts

BASIC

OPERATION

■ Manual station preset

Use this feature to preset your desired station

manually.

1 Tune into a radio station you want to

preset.

2 Press MEMORY.

“MANUAL PRESET” appears in the front panel

display, followed soon by the preset number to

which the station will be registered.

By pressing down MEMORY for more than 2

seconds. The station is registered to the lowest empty

preset number or a preset number one higher than the

last preset number.

3 Press PRESET / to select the preset

number (01 to 40) to which the station will

be registered.

When you select a preset number to which no

station is registered, EMPTY indicator appears on

the display. When you select a registered preset

number, a registered frequency is displayed on the

right of the preset number.

To cancel registration, press RETURN on the remote

control or leave the tuner without any operations for

about 30 seconds.

4 Press MEMORY again to register.

■ Clearing the preset station

1 Press OPTION to enter OPTION menu.

2 Display “CLEAR PRESET” using the

cursor and press (Center).

Preset number and the frequency appears in the

display.

You can cancel the operation and return to OPTION

menu by pressing RETURN on the remote control.

3 Select the preset number of the registered

station you want to clear using the cursor

/ and press (Center).

The preset station registered to the selected preset

number is cleared. To clear the registration of

multiple preset numbers, repeat the above steps.

To end the operation, press OPTION.

■ Using the monaural

reception mode

When the signal of the desired FM station is too weak,

set the reception mode to “MONO” to increase signal

quality.

1 Press OPTION to enter OPTION menu.

2 Display “STEREO/MONO” by using the

cursor and press (Center).

3 Select “MONO” to set the reception mode

to monaural by using the cursor / .

■ Switching the information

display

Each time you press INFO, the information display

changes as follows:

Information type

• SURROUND MODE

Displays the surround mode or stereo mode.

• FREQUENCY

Displays the frequency and preset number.

• PROGRAM SERVICE (PS)

Displays the currently received Radio Data System

program.

• PROGRAM TYPE (PTY)

Displays the type of the currently received Radio

Data System program.

• RADIO TEXT (RT)

Displays the information of the currently received

Radio Data System program.

• CLOCK TIME (CT)

Displays the current time.

Europe and Russia models only

16 En

This system is equipped with a DOCK terminal, which allows you to connect a Yamaha iPod universal dock (such

as YDS-11, sold separately) or a Yamaha Bluetooth wireless audio receiver (such as YBA-10, sold separately) to

enjoy music contents stored in your Bluetooth component (such as a portable music player or computer equipped

with Bluetooth transmitter, etc.). Connect this equipment to the DOCK terminal of the subwoofer integrated

receiver using its dedicated cable.

When DOCK is selected as the input source, compressed music enhancer function is activated automatically and enhances

your listening experience by regenerating the missing harmonics in a compressed music format such as MP3.

Once you have stationed your iPod in the Yamaha iPod universal dock connected to the DOCK terminal of the

subwoofer integrated receiver, you can enjoy playback of your iPod.

Supported iPod

iPod (Click and Wheel including iPod classic)

iPod nano

iPod mini

iPod touch

Battery charge feature

This system charges the battery of an iPod stationed in the Yamaha iPod universal dock connected to the DOCK

terminal of the subwoofer integrated receiver, even when this system is turned off. “Charging” appears in the

front panel display.

• Some features may not be available depending on the model or the software version of your iPod.

• For a complete list of status messages that appear in the front panel display, see the “iPod” section in “Troubleshooting” (☞

P. 24).

• Be sure to set the volume to minimum before docking or removing your iPod.

• To playback an iPod, select DOCK for input source.

• Refer to the instruction manual of your Yamaha iPod universal dock for details.

Using optional equipment

Connecting dock

Using iPod™

Notes

Yamaha iPod universal dock

(such as YDS-11, sold separately)

Yamaha Bluetooth wireless audio receiver

(such as YBA-10, sold separately)

Connect either component.

17 En

Using optional equipment

BASIC

OPERATION

■ Pairing

For details, refer to the instruction manual of Yamaha

Bluetooth wireless audio receiver.

1 Press DOCK to set the input to DOCK.

2 Turn on the Bluetooth component you

want to pair with, and then enter pairing

mode.

Refer to the instruction manual of your Bluetooth

component for details.

3 Press OPTION.

OPTION menu for DOCK input appears in the

display.

4 Press the cursor to select “PAIRING”

and press (Center).

“Searching...” appears when the pairing starts.

While the Yamaha Bluetooth wireless audio

receiver is in pairing mode, the DOCK indicator

flashes in the front panel display.

To cancel pairing, press RETURN.

5 Check that the Bluetooth component

detects the Yamaha Bluetooth wireless

audio receiver.

If the Bluetooth component detects the Yamaha

Bluetooth wireless audio receiver, the audio

receiver name (“YBA-10 YAMAHA” for

example) appears in the device list of the

Bluetooth component.

6 Select the Yamaha Bluetooth wireless

audio receiver in the device list of the

Bluetooth component, and then enter the

pass key “0000” on the Bluetooth

component.

■ Establishing a connection

After the pairing is completed, perform the connecting

operation on the system or on the Bluetooth

component to enable communication between them.

The connecting operation on the system is only

available for the most recently connected Bluetooth

component.

1 Press DOCK to set the input to DOCK.

2 Press OPTION to enter OPTION menu.

“CONNECT” appears firstly in the front panel

display.

3 Press (Center).

“Searching...” appears firstly in the front panel

display.

When the system finds the last connected

Bluetooth component, “BT connected” appears in

the front panel display for 3 seconds.

• If the system cannot find the last connected Bluetooth

component, “Not found” appears in the front panel

display.

• If you want to establish a connection with a Bluetooth

component other than the one most recently

connected to, connect from that Bluetooth

component. Refer to the instruction manual of your

Bluetooth component for details.

To disconnect the Bluetooth wireless audio receiver from

the Bluetooth component, display OPTION menu again,

select “Disconnected,” and press (Center).

Using Bluetooth™ components

About “Pairing”

Pairing must be performed before using a Bluetooth

component with the Yamaha Bluetooth wireless

audio receiver connected to the system for the first

time or if the registered pairing data has been

deleted. “Pairing” refers to the operation of

registering a Bluetooth component for Bluetooth

communications.

To ensure security, a time limit of 8 minutes is set for the

pairing operation. Please read and fully understand all the

instructions before starting.

Note

18 En

USEFUL OPERATION

■ Setup menu list

You can change various settings of this system using

the setup menu.

1 Press SETUP to enter the setup menu.

“SW LEVEL” is displayed in the front panel

display.

2 Press the cursor / to select menu

and press (Center).

The current setting is displayed.

3 Press the cursor / to adjust the

value of each menu.

Press and hold the cursor / to change the

setting value faster.

4 Press SETUP again to exit the setup

menu.

Press RETURN to return to the previous menu.

If you do not operate within 30 seconds after entering the

setup menu, the system automatically exits the setup menu.

Setup menu

Overview

Item Description of function Page

1: SW LEVEL

Adjusting the volume balance during playback ☞ P. 192: CENTER LEVEL

3: SUR. LEVEL

4: TONE BASS

Adjusting high/low frequency sound (tone control) ☞ P. 19

5: TONE TREBLE

6: AUDIO DELAY Adjusting the audio delay ☞ P. 19

7: HDMI AUDIO Setting the audio output ☞ P. 19

8: HDMI CONTROL Switching on/off the HDMI control function ☞ P. 19

9: DISPLAY MODE Changing the brightness of the front panel display ☞ P. 20

10: SP TYPE Changing the setting of the speaker type ☞ P. 20

11: SP DISTANCE Setting the distance between the speakers ☞ P. 20

Basic procedure

1, 4

2, 3

Note

19 En

Setup menu

USEFUL

OPERATION

You can adjust the volume balance of the virtual

speakers and subwoofer.

Parameter

“SW LEVEL”: Adjusts the output level of the

subwoofer channel.

“CENTER LEVEL”: Adjusts the output level of the

virtual center speaker channel.

“SUR. LEVEL”: Adjusts the output level of the

surround/surround back virtual speaker channels.

Adjustable range

–6 to +6 (Default setting: 0)

• You can also adjust the output level of the subwoofer by

pressing SUBWOOFER +/–.

• If surround mode is off, the virtual center speaker and

virtual surround effects become invalid.

You can adjust the balance of the high frequency

range (Treble) and low frequency range (Bass) of

sounds output from the front speakers to obtain

desired tone.

Parameter

“TONE BASS”: Adjusts the balance of the low

frequency range (Bass) of sounds output from the

speaker.

“TONE TREBLE”: Adjusts the balance of the high

frequency range (Treble) of sounds output from the

speaker.

Adjustable range

–6 to +6 (Default setting: 0)

Flat panel display TV images sometimes lag behind

the sound. You can use this function to delay the

sound output to synchronize it with the video image.

Parameter

“AUDIO DELAY”

Adjustable range (Default setting: “AUTO”)

“AUTO”, 0 to 240 ms (You can adjust the delay time

by the 10 ms.)

* “AUTO”: If you operate HDMI connection to a TV with

the function to automatically adjusting the audio delay,

you can adjust the delay time automatically.

The system memorizes the settings assigned to each input

source.

You can select this system (or a TV connected to this

system via the HDMI OUT jack of this system) for

reproducing sound signals input from the HDMI IN

jack in the setup menu.

Parameter

“HDMI AUDIO”

Adjustable option (Default setting: “AMP”)

“AMP”: Outputs HDMI sound signals from the

speakers connected to this system.

“TV”: Outputs HDMI sound signals from the speakers

of a TV connected to this system. Sound output from

the speakers connected to this system is muted.

• The volume level will not change from pressing

VOLUME +/– or MUTE while output from the TV.

• You cannot change the audio output when “HDMI

CONTROL” is set to “ON”.

You can set whether to use the HDMI control

function. Refer to P.21 for HDMI control function.

Parameter

“HDMI CONTROL”

Adjustable option (Default setting: “OFF”)

“ON”: Activates the HDMI control function.

“OFF”: Deactivates the HDMI control function.

Adjusting the volume balance

during playback

Adjusting high/low frequency

sound (tone control)

Adjusting the audio delay

Note

Setting the audio output

Notes

Switching on/off the HDMI™

control function

Setup menu

20 En

You can change the brightness of the front panel

display. You can also turn off the front panel display

to view a movie in a darker environment.

The brightness of the front panel changes as follows.

Parameter

“DISPLAY MODE”

Adjustable range

(Default setting: “DIMMER 0”)

* Selecting DISPLAY OFF turns off the front panel display

after exiting the setup menu.

• The front panel display lights up momentarily when any

operation is performed with DISPLAY OFF mode selected.

• Only the STATUS indicator remains lit in DISPLAY OFF

mode.

You can set the speaker type if you want to add or

change speakers. When you connect only the supplied

speaker, you do not have to change the setting.

Parameter

“SP TYPE”

Adjustable range (Default setting: “2CH”)

“BAR”: When you connect a speaker with integrated

front left/right/center channels (such as a bar-type

speaker).

“2CH”: When you connect front left/right (2-channel)

speakers.

“3CH”: When you connect front left/right (2-channel)

speakers and a center speaker.

• To activate “SP TYPE”, set the system to standby mode

and turn on again after setting the speaker type.

• “SP DISTANCE” is displayed when “2CH” or “3CH” is

selected.

Select a parameter suited for the distance between the

front left and right speakers, to obtain the most

suitable surround effect.

Parameter

“SP DISTANCE”

Adjustable range

(Default setting: “NORMAL”)

“WIDE”: When the distance between the front

speakers is over 150 cm (59-1/16”).

“NORMAL”: When the distance between the front

speakers is from 80 cm (31-1/2”) to 150 cm (59-1/

16”).

“NARROW”: When the distance between the front

speakers is within 80 cm (31-1/2”).

When the surround mode is off, this function is invalid.

Changing the brightness of the

front panel display

Notes

Changing the setting of the

speaker type

Notes

Bright

Dark

Setting the distance between the

speakers

Note

Sidan laddas ...

Yamaha YHT-S300 Bruksanvisning

varumärke: Yamaha

Modell: YHT-S300

Kategori: AV-mottagare

Typ: Bruksanvisning

Ladda ner pdf

Rapportera

på andra språk

italiano: Yamaha YHT-S300 Manuale del proprietario
Deutsch: Yamaha YHT-S300 Bedienungsanleitung
français: Yamaha YHT-S300 Le manuel du propriétaire
English: Yamaha YHT-S300 Owner's manual
dansk: Yamaha YHT-S300 Brugervejledning
suomi: Yamaha YHT-S300 Omistajan opas
Nederlands: Yamaha YHT-S300 de handleiding
română: Yamaha YHT-S300 Manualul proprietarului

Yamaha YHT-S300 Bruksanvisning

Yamaha YHT-S300 Bruksanvisning

på andra språk

Relaterade papper

Andra dokument