Yamaha DRX-1 Användarmanual

varumärke: Yamaha

Modell: DRX-1

Kategori: DVD-spelare

Typ: Användarmanual

Denna manual är också lämplig för

DRX1

DVD Recorder

Enregistreur de DVD

DRX-1

OWNER’S MANUAL

MODE D’EMPLOI

Important safety instructions

1. Read Instructions — All the safety and operating instructions should

be read before the appliance is operated.

2. Retain Instructions — The safety and operating instructions should be

retained for future reference.

3. Heed Warnings — All warnings on the appliance and in the operating

instructions should be adhered to.

4. Follow Instructions — All operating and use instructions should be

followed.

5. Cleaning — Unplug this product from the wall outlet before cleaning.

Do not use liquid cleaners or aerosol cleaners.

Use a damp cloth for cleaning.

Exception: A product that is meant for uninterrupted service and that for

some speciﬁc reason, such as the possibility of the loss of an

authorization code for a CATV converter, is not intended to be

unplugged by the user for cleaning or any other purpose, may exclude

the reference to unplugging the appliance in the cleaning description

otherwise required in item 5.

6. Attachments — Do not use attachments not recommended by the

video product manufacturer as they may cause hazards.

7. Water and Moisture — Do not use this video product near water - for

example, near a bath tub, wash bowl, kitchen sink, or laundry tub, in a

wet basement, or near a swimming pool, and the like.

8. Accessories — Do not place this video product on an unstable cart,

stand, tripod, bracket, or table. The video product may fall, causing

serious injury to a child or adult, and serious damage to the appliance.

Use only with a cart, stand, tripod, bracket, or table recommended by

the manufacturer or sold with the video product. Any mounting of the

appliance should follow the manufacturer’s instructions and should use a

mounting accessory recommended by the manufacturer.

8A.

9. Ventilation — Slots and openings in the cabinet are provided for

ventilation, to ensure reliable operation of the video product, and to

protect it from overheating. These openings must not be blocked or

covered. The openings should never be blocked by placing the video

product on a bed, sofa, rug,

or other similar surface. This video product should never be placed near

or over a radiator or heat register. This video product should not be

placed in a built-in installation such as a bookcase or rack unless proper

ventilation is provided or the manufacturer’s instructions have been

adhered to.

10. Power Sources — This video product should be operated only from

the type of power source indicated on the marking label. If you are not

sure of the type of power supply to your home, consult your appliance

supplier or local power company. For video products intended to

operate from battery power, or other sources, refer to the operating

instructions.

11. Polarization — This product may be equipped with a polarized

alternating-current line plug (a plug having one blade wider than the

other). This plug will ﬁt into the power outlet only one way. This is a

safety feature. If you are unable to insert the plug fully into the outlet, try

reversing the plug.

If the plug should still fail to ﬁt, contact your electrician to replace your

obsolete outlet. Do not defeat the safety purpose of the polarized plug.

12. Power-Cord Protection — Power supply cords should be routed so

that they are not likely to be walked on or pinched by items placed upon

or against them, paying particular attention to cords at plugs,

convenience receptacles,

and the point where they exit from the appliance.

13. Outdoor Antenna Grounding — If an outside antenna or cable

system is connected to the video product, be sure the antenna or cable

system is grounded so as to provide some protection against voltage

surges and built-up static charges.

Section 810 of the National Electrical Code, ANSI/NFPA 70, provides

information with regard to proper grounding of the mast and supporting

structure, grounding of the lead-in wire to an antenna discharge unit, size

of grounding conductors, location of antenna-discharge unit, connection

to grounding electrodes, and requirements for the grounding electrode.

See Fig.A.

Fig.A.

14. Lightning — For added protection for this product during a lightning

storm, or when it is left unattended and unused for long periods of time,

unplug it from the wall outlet and disconnect the antenna or cable

system. This will prevent damage to the product due to lightning and

power surges.

15. Power lines — An outside antenna system should not be located in

the vicinity of overhead power lines or other electric light or power

circuits, or where it can fall into such power lines or circuits. When

installing an outside antenna system, extreme care should be taken to

keep from touching such power lines or circuits as contact with them

might be fatal.

16. Overloading — Do not overload wall outlets and extension cords as

this can result in a risk of ﬁre or electric shock.

17. Object and Liquid Entry — Never push objects of any kind into this

product through openings as they may touch dangerous voltage points or

short-out parts that could result in a ﬁre or electric shock. Never spill

liquid of any kind on the product.

18. Servicing — Do not attempt to service this product yourself, as

opening or removing covers may expose you to dangerous voltage or

other hazards. Refer all servicing to qualiﬁed service personnel.

19. Damage Requiring Service — Unplug this product from the wall

outlet and refer servicing to qualiﬁed service personnel under the

following conditions:

a. When the power-supply cord or plug is damaged.

b. If liquid has been spilled on, or objects have fallen into the product.

c. If the product has been exposed to rain or water.

d. If the product does not operate normally by following the operating

instructions. Adjust only those controls that are covered by the operating

instructions as an improper adjustment of other controls may result in

damage and will often require extensive work by a qualiﬁed technician to

restore the product to its normal operation.

e. If the product has been dropped or the cabinet has been damaged.

f. When the product exhibits a distinct change in performance - this

indicates a need for service.

20. Replacement Parts — When replacement parts are required, be sure

the service technician has used replacement parts speciﬁed by the

manufacturer or which have the same characteristics as the original part.

Unauthorized substitutions may result in ﬁre, electric shock or other

hazards.

21. Safety Check — Upon completion of any service or repairs to this

product, ask the service technician to perform safety checks to

determine that the product is in proper operating condition.

22. Carts and Stands — The appliance should be used only with a cart or

stand that is recommended by the manufacturer.

23. Heat — The product should be situated away from heat sources such

as radiators, heat registers, stoves, or other products that produce heat.

This “bolt of lightning” indicates uninsulated material within

your unit may cause an electrical shock. For the safety of

everyone in your household, please do not remove product

covering.

The “exclamation point” calls attention to features for

which you should read the enclosed literature closely to

prevent operating and maintenance problems.

WARNING:

TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE

THIS EQUIPMENT TO RAIN OR MOISTURE.

CAUTION:

To prevent electric shock, match wide blade of plug to wide slot,

and fully insert.

ATTENTION:

Pour éviter les chocs électriques, introduire la lame la plus large

de la ﬁche dans la borne correspondante de a prise et pousser

jusqu’au fond.

CAUTION:TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK).

NO USER-SERVICEABLE PARTSINSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

An appliance and cart combination should be moved with

care. Quick stops, excessive force, and uneven surfaces

may cause the appliance and cart combination to

overturn.

ANTENNA LEAD

IN WIRE

ANTENNA

DISCHARGE UNIT

(NEC SECTION 810-20)

GROUNDING

CONDUCTORS

(NEC SECTION 810-21)

GROUND

CLAMPS

POWER SERVICE GROUNDING

ELECTRODE SYSTEM

(NEC ART 250, PART H)

GROUND CLAMP

ELECTRIC SERVICE EQUIPMENT

EXAMPLE OF ANTENNA GROUNDING AS

PER NATIONAL ELECTRICAL CODE (NEC)

GENERAL INFORMATION

English

Laser safety

This unit employs a laser. To prevent possible eye injury, only a qualiﬁed service person should remove the cover or attempt to service this

device.

USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED

HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.

VISIBLE AND INVISIBLE LASER RADIATION.

WHEN OPEN AVOID EXPOSURE TO BEAM.

(WARNING LOCATION: INSIDE ON LASER

COVERSHIELD)

ONLY QUALIFIED SERVICE PERSONNEL

SHOULD REMOVE THE COVER OR

ATTEMPT TO SERVICE THIS DEVICE.

FCC INFORMATION (for US customers)

1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!

This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modiﬁcations not

expressly approved by Yamaha may void your authority, granted by the FCC, to use the product.

2. IMPORTANT: When connecting this product to accessories and/or another product use only high quality shielded cables. Cable/s

supplied with this product MUST be used. Follow all installation instructions. Failure to follow instructions could void your FCC

authorization to use this product in the USA.

3. NOTE: This product has been tested and found to comply with the requirements listed in FCC Regulations, Part 15 for Class “B”

digital devices. Compliance with these requirements provides a reasonable level of assurance that your use of this product in a

residential environment will not result in harmful interference with other electronic devices. This equipment generates/uses radio

frequencies and, if not installed and used according to the instructions found in the users manual, may cause interference harmful

to the operation of other electronic devices. Compliance with FCC regulations does not guarantee that interference will not occur

in all installations. If this product is found to be the source of interference, which can be determined by turning the product “OFF”

and “ON”, please try to eliminate the problem by using one of the following measures:

Relocate either this product or the device that is being affected by the interference.

Utilize power outlets that are on different branch (circuit breaker or fuse) circuits or install AC line ﬁlter/s.

In the case of radio or TV interference, relocate/reorient the antenna. If the antenna lead-in is 300 ohm ribbon lead, change the

lead-in to coaxial type cable.

If these corrective measures do not produce satisfactory results, please contact the local retailer authorized to distribute this type

of product. If you can not locate the appropriate retailer, please contact Yamaha Electronics Corp., 6600 Orangethorpe Ave. Buena

Park, CA90622.

The above statements apply ONLY to those products distributed by Yamaha Corporation of America or its subsidiaries.

THIS DIGITAL APPARATUS DOES NOT EXCEED THE

CLASS B LIMITS FOR RADIO NOISE EMISSIONS FROM

DIGITAL APPARATUS AS SET OUT IN THE RADIO

INTERFERENCE REGULATIONS OF THE CANADIAN

DEPARTMENT OF COMMUNICATIONS.

CET APPAREIL NUMÉRIQUE N'ÉMET PAS DE BRUITS

RADIOÉLECTRIQUES DÉPASSANT LES LIMITES

APPLICABLES DANS LA RÈGLEMENT SUR LE

BROUILLAGE RADIOÉLECTRIQUES ÉDICTÉ PAR LE

MINISTÈRE DES COMMUNICATIONS DU CANADA.

NOTE TO CABLE TV SYSTEM INSTALLER:

This reminder is provided to call the Cable TV (CATV)

system installer’s attention to Article 820-40 of the NEC

(National Electrical Code) that provides guidelines for proper

grounding and, in particular, speciﬁes that the cable ground

shall be connected to the grounding system of the building, as

close to the point of cable entry as practical.

LASER

Type Semiconductor laser GaAlAs (DVD)

Semiconductor laser AlGaAs (CD)

Wavelength 660 nm (DVD)

780 nm (CD)

Output Power 20 mW (DVD +RW writing)

(out of objective) 0,8 mW (DVD reading)

0,3 mW (CD reading)

Beam divergence 82 degrees (DVD)

54 degrees (CD)

CAUTION

For Customer Use:

Read carefully the information located on the back of your

DVD recorder and enter below the Serial No. Retain this

information for future reference.

Model No.

Serial No.__________________________

GENERAL INFORMATION

CAUTION

Read this before operating your unit.

1 To assure the ﬁnest performance, please read this

manual carefully. Keep it in a safe place for future ref-

erence.

2 The recommended operating temperature range for

the Recorder is from 60˚F-95˚F (Fahrenheit). Exceed-

ing these ranges may cause unstable recording results.

Do not expose this unit to sudden temperature

changes from cold to hot, nor locate this unit in an

environment with high humidity (i.e., a room with a

humidiﬁer) to prevent condensation inside this unit,

which may cause an electrical shock, ﬁre, damage to

this unit, and/or personal injury.

3 Locate this unit away from other electrical appliances,

motors, or transformers to avoid humming sounds.

4 Install this unit in a well ventilated, cool, dry, clean

place — away from direct sunlight, heat sources,

vibration, dust, moisture, or cold. In a cabinet, allow

about 2.5cm (1 inch) of free space all around this unit

for adequate ventilation.

5 Avoid installing this unit in a location where foreign

objects may fall onto this unit or where this unit may

be exposed to liquid dripping or splashing. On the top

of this unit, do not place:

– Other components, as they may cause damage and/

or discoloration on the surface of this unit.

– Burning objects (i.e., candles), as they may cause

ﬁre, damage to this unit, and/or personal injury.

– Containers with liquid in them, as they may fall,

spilling the liquid and causing an electrical shock to

the user and/or damage to this unit.

6 Do not cover this unit with a newspaper, tablecloth,

curtain, etc. in order not to obstruct heat radiation. If

the temperature inside this unit rises, it may cause

ﬁre, damage to this unit, and/or personal injury.

7 Do not plug in this unit to a wall outlet until all con-

nections are complete.

8 Do not operate this unit upside-down. It may over-

heat, possibly causing damage.

9 Do not use excessive force on switches, knobs and/or

cords.

10 When disconnecting the power cord from the wall

outlet, grasp the plug; do not pull the cord.

11 Do not clean this unit with chemical solvents; this

might damage the ﬁnish. Use a clean, dry cloth.

12 Use only the voltage speciﬁed on this unit. Using this

unit with a higher voltage than speciﬁed is dangerous

and may cause ﬁre, damage to this unit, and/or per-

sonal injury. YAMAHA will not be held responsible for

any damage resulting from use of this unit with a volt-

age other than as speciﬁed.

13 To prevent damage by lightning, disconnect the power

cord from the wall outlet during an electrical storm.

14 Do not attempt to modify or ﬁx this unit. Contact

qualiﬁed YAMAHA service personnel when any ser-

vice is needed. The cabinet should never be opened

for any reason.

15 When not planning to use this unit for long periods of

time (i.e., vacation), disconnect the AC power plug

from the wall outlet.

16 Be sure to read the “TROUBLESHOOTING” section

on common operating errors before concluding that

this unit is faulty.

17 Before moving this unit, press STANBY/ON to set the

unit in standby mode, then disconnect the AC power

plug from the wall outlet.

Supplied Accessories

- Remote Control with separately-packed batteries

- 2-core power cord

- Component video cable

- S-Video cable

- Antenna cable

- Audio cable (2x)

- Video cable

- DVD+RW disc

If any item is damaged or missing, please inform your

supplier without delay.

Keep the packaging materials; you may need them to

transport your Recorder in the future.

FOR CANADIAN CUSTOMERS

To prevent electric shock, match wide blade of plug to wide

slot and fully insert.

This Class B digital apparatus complies with Canadian ICES-003.

This digital apparatus does not exceed the Class B limits for

radio noise emissions from digital apparatus as set out in the

Radio Interference Regulations of the Canadian Department

of Communications.

CAUTION

CONTENTS 1

English

Contents

Introduction__________________________________2

DVD Recorder ____________________________________________ 2

Cleaning discs _____________________________________________ 2

Remote control____________________________________________ 2

Installation ___________________________________3

Connections - back of your DVD Recorder _____________________ 3

Step 1: Connecting to the antenna or Cable TV signal _____________ 3

Step 2: Connecting to a TV __________________________________ 3

Step 3: Connecting to audio equipment_________________________ 4

Step 4: Connecting to other equipment (optional) ________________ 5

Step 5: Connections - Front of your DVD Recorder (optional) ______ 6

Step 6: Power supply________________________________________ 6

Switching on ______________________________________________ 6

First time setup: Initial setup__________________________________ 7

Functional overview __________________________9

Front of recorder __________________________________________ 9

Back of Recorder _________________________________________ 10

Display__________________________________________________ 11

Remote control___________________________________________ 12

Operation___________________________________13

Important notes for operation _______________________________ 13

Loading discs _____________________________________________ 13

Disc types _______________________________________________ 13

On-screen display information _______________________________ 14

Index Picture Screen_______________________________________ 18

User preferences__________________________________________ 19

Recording ___________________________________24

Before you start recording __________________________________ 24

Manual recording of a TV channel or from a video camera ________ 24

Timer programming _______________________________________ 26

If a timer recording is incorrect ______________________________ 28

Playback ____________________________________30

Playing a DVD+RW/+R disc _________________________________ 30

Playing a pre-recorded DVD-Video disc _______________________ 30

Playing a (Super) Video CD _________________________________ 30

General features __________________________________________ 31

Special DVD+RW/+R features _______________________________ 34

Special DVD-Video features _________________________________ 34

Special VCD features ______________________________________ 35

Playing an Audio CD_______________________________________ 36

Access control_______________________________37

Child Lock (DVD and VCD)_________________________________ 37

Parental Level (DVD-Video only) _____________________________ 38

Country_________________________________________________ 39

Changing the 4-digit code ___________________________________ 39

Managing disc content (DVD+RW/+R only) ____40

Title settings _____________________________________________ 40

Disc Information Screen ____________________________________ 40

Disc Settings _____________________________________________ 41

Editing __________________________________________________ 42

Troubleshooting _____________________________45

Diagnosis program ________________________________________ 47

DVD Recorder system notes ________________________________ 47

Glossary ____________________________________48

Appendix ___________________________________49

Using your DVD Recorder remote control with your TV _________ 49

Specifications _______________________________51

VCR Plus+ and PlusCode are registered trademarks of

Gemstar Development Corporation.The VCR Plus+ system is

manufactured under license from Gemstar Development

Corporation.

Pats. 5,307,173; 5,335,079; 4,908,713; 4,751,578; and

4,706,121

Manufactured under license from Dolby Laboratories.

“Dolby,” “Pro Logic” and the double-D symbol are

trademarks of Dolby Laboratories. Conﬁdential Unpublished

Works.

“DTS” and “DTS Digital Out” are trademarks of Digital

Theater Systems, Inc.

DCDi is a trademark of Faroudja, a division of Sage Inc.

This product incorporates copyright protection technology

that is protected by method claims of certain U.S. patents

and other intellectual property rights owned by Macrovision

Corporation and other rights owners.

Use of this copyright protection technology must be

authorized by Macrovision Corporation, and is intended for

home and other limited viewing uses only unless otherwise

authorized by Macrovision Corporation. Reverse engineering

or disassembly is prohibited.

TRUSURROUND, , and symbol

are trademarks of

SRS Labs,Inc. TRUSURROUND technology is manufactured

under license from SRS Labs, Inc.

2 INTRODUCTION

Introduction

DVD Recorder

DVD (Digital Versatile Disc) is the new storage medium

that combines the convenience of the Compact Disc with

the latest advanced digital video technology.

DVD Video uses state-of-the-art MPEG2 data compression

technology to register an entire movie on a single 5-inch

disc. DVD’s variable bitrate compression, running at up to

9.8 Mbits/second, captures even the most complex

pictures in their original quality.

The crystal-clear digital pictures have a horizontal

resolution of over 500 lines, with 720 pixels (picture

elements) to each line. This resolution is more than double

that of VHS, superior to Laser Disc, and entirely

comparable with digital masters made in recording studios.

DVD recording is the next step in video technology.

DVD+ReWritable (DVD+RW) uses phase-change media,

the same technology that formed the basis for CD-

ReWritable. A high-power laser is used to change the

reﬂectivity of the recording layer. This process can be

repeated more than a thousand times. DVD+Recordable

(DVD+R) uses discs based on an organic dye, a technology

pioneered with the successful CD-Recordable format, to

produce discs that keep your data for a lifetime.

Your DVD Recorder is a Recorder and player for digital

video discs, with a two-way compatibility to the

universal DVD Video standard. This means that:

- existing pre-recorded DVD Video discs can play on

your DVD Recorder and

- recordings, made on your DVD Recorder,

can play on most DVD Video players and DVD-ROM

drives.

With it, you will be able to record TV programs or edit

and archive your own video camera recordings.

Superb digital picture and sound quality, quick access to

the tracks you have recorded and extensive playback

features contribute to a completely new video experience.

From now on you will enjoy full-length movies with true

cinema picture quality and stereo or Multi-channel sound

(depending on the disc and on your playback set-up). You

will ﬁnd your Recorder remarkably easy to use, with the

on-screen display on your TV, the display on the DVD

recorder and remote control.

Cleaning discs

Some problems occur because the disc inside the

Recorder is dirty. To avoid these problems, clean your

discs regularly in the following way:

● When a disc becomes dirty, clean it with a cleaning

cloth. Wipe the disc in a straight line from the center

out to the edge.

Caution:

Do not use solvents such as benzine, thinner,

commercially available cleaners, or anti-static

spray intended for analog discs.

Do not use commercially available cleaning discs to

clean the lens, as these discs may damage the

optical unit.

Remote control

Loading the batteries

1 Remove the battery compartment cover.

2 Insert two ‘AA’ (LR-6) batteries as indicated inside the

battery compartment.

3 Replace the cover.

Caution:

Do not mix old and new batteries. Never mix

different types of batteries (standard, alkaline,

etc.). This may reduce the lifetime of the batteries.

pre-recorded DVDDVD+R(W)

DVD Video

player

DVD recorder

INSTALLATION 3

English

Installation

Connections - back of your DVD

Recorder

- Please refer to your TV, VCR, Stereo and any other User

Manual(s) as necessary to make the optimal connections.

- Do not connect the power cords until all other

connections are made.

- Do not connect your DVD Recorder to your TV via your

VCR. The video quality could be distorted by the copy

protection system.

- For better sound, connect the Recorder’s audio outputs

to your ampliﬁer, receiver, stereo system or A/V

equipment. See ‘Connecting to an A/V receiver or A/V

ampliﬁer.’

Caution:

Do not connect the Recorder’s audio output to the

phono input of your audio system. This could

damage your equipment.

Step 1: Connecting to the

antenna or Cable TV signal

1 Remove the antenna cable from your TV and connect

it to the ANTENNA jack at the back of the DVD

Recorder.

2 Connect one end of the antenna cable supplied (1) to

the TV jack on the DVD Recorder and the other end

to the antenna input jack on your TV.

The antenna connection transmits TV channels through

the Recorder to the TV. You still need a video connection

to send DVD playback from the Recorder to the TV. See

‘Connecting to a TV.’

Step 2: Connecting to a TV

This DVD Recorder is equipped with Directional

Correlational Deinterlacing, known as DCDi™. DCDi was

developed by Faroudja Laboratories for ultra-high-end

home theater equipment to eliminate the jagged edges

that appear when standard interlaced video is viewed on

Progressive Scan displays. This patented technology

identiﬁes edges at any angle in moving video images and

interpolates along the edge, pixel-by-pixel, to produce

smooth, natural looking images.

To obtain the highest possible picture and sound quality

from your TV, use the Progressive Scan video jacks on the

DVD Recorder and TV.

Progressive Scan connection

● Connect the PROG SCAN OUT (YP

) jacks on the

Recorder to the corresponding IN jacks on the TV,

using the Component Video cable supplied (2) as

shown in the drawing.

● Connect the audio Left (white) and Right (red) OUT

jacks on the Recorder to the corresponding AUDIO

IN jacks on the TV using the audio cables supplied (4).

Note:

The PROG SCAN OUT jacks do not carry Closed Captioning or

V-chip signals. These features will not be available if you use the

Progressive Scan connection.

Component Video (YP

) connection

If your TV does not have Progressive Scan, connect the

DVD Recorder with the Component Video jacks.

● Connect the COMPONENT VIDEO (YP

) OUT

jacks to the corresponding IN jacks on the TV, using

the Component Video cable supplied (2) as shown in

the drawing.

● Connect the AUDIO Left (white) and Right (red)

OUT jacks to the corresponding AUDIO IN jacks on

the TV using the audio cable supplied (4).

● Do not connect a Progressive Scan video source to

the Component Video IN jacks on your TV.

Apparatus Claims of U. S. Patent Nos.

4,631,603, 4,577,216, 4,819,098, and 4,907,093

COMPONENT VIDEO PROG

SCAN

EXT 2

EXT 3 EXT 3

EXT 1 EXT 1/2

Apparatus Claims of U. S. Patent Nos.

4,631,603, 4,577,216, 4,819,098, and 4,907,093

licensed for limited viewing uses only.

COMPONENT VIDEO PROG

SCAN

EXT 2

EXT 3 EXT 3

EXT 1 EXT 1/2

RC 6

4 INSTALLATION

S-Video (Y/C) connection

If your TV is not equipped with COMPONENT VIDEO

inputs, connect the DVD Recorder with the

S-Video (Y/C) jacks.

● Connect the S-Video (Y/C) OUT jack to the

corresponding IN jacks on the TV, using the

S-Video cable supplied (3) as shown in the drawing.

● Connect the AUDIO Left (white) and Right (red)

OUT jacks to the corresponding IN jacks on the TV

using the audio cable supplied (4).

Video (CVBS) connection

If your TV is not equipped with a S-Video jack, then

connect the DVD Recorder’s VIDEO (CVBS) OUT jack to

your TV.

● Connect the VIDEO (CVBS) OUT jacks (yellow)

to the corresponding IN jacks on the TV using the

video cable supplied (5) as shown in the drawing.

● Connect the AUDIO Left (white) and Right (red)

OUT jacks to the corresponding IN jacks on the TV

using the audio cable supplied (4).

Step 3: Connecting to audio

equipment

Connecting to an A/V receiver or A/V

ampliﬁer with a digital Multi-channel

decoder

The best possible sound quality is obtained by connecting

your DVD Recorder to an Audio/Video receiver with

Multi-channel decoder (Dolby Digital, MPEG 2 and DTS).

Digital Multi-channel sound

A digital Multi-channel connection provides the optimum

sound quality. For this you need a Multi-channel A/V

receiver that supports one or more of the audio types

supported by your DVD Recorder (MPEG 2, Dolby Digital

and DTS). Check the receiver manual and the logos on the

front of the receiver.

● Connect one of the DVD Recorder’s DIGITAL

AUDIO OUT jacks to the corresponding IN jacks on

the receiver. Use a digital coaxial cable (6) or a digital

optical audio cable (7).

● Connect the recorder’s component video, S-Video or

Video (CVBS) OUT jack to the corresponding IN jack

of your ampliﬁer. Then make the same connection

between your ampliﬁer and your TV (8).

● You can connect your VCR’s audio/video IN/OUT

jacks to your ampliﬁer. Refer to the manual supplied

with your ampliﬁer.

Note:

If you use a connection that does not match the capabilities of

your receiver, the receiver will produce a strong, distorted

sound. The audio type of the current DVD disc will appear in

the Status Window when you change the language.

Six Channel Digital Surround Sound via digital connection can

only be obtained if your receiver has a Digital Multi-channel

decoder.

Apparatus Claims of U. S. Patent Nos.

4,631,603, 4,577,216, 4,819,098, and 4,907,093

licensed for limited viewing uses only.

COMPONENT VIDEO PROG

SCAN

EXT 2

EXT 3 EXT 3

EXT 1 EXT 1/2

Apparatus Claims of U. S. Patent Nos.

4,631,603, 4,577,216, 4,819,098, and 4,907,093

licensed for limited viewing uses only.

COMPONENT VIDEO PROG

SCAN

EXT 2

EXT 3 EXT 3

EXT 1 EXT 1/2

RC 6

Apparatus Claims of U. S. Patent Nos.

4,631,603, 4,577,216, 4,819 ,098, and 4,9 07,093

licensed for limited viewing uses only.

COMPONENT VIDEO PROG

SCAN

EXT 2

EXT 3 EXT 3

EXT 1 EXT 1/2

RC 6

AMPLIFIER

INSTALLATION 5

English

If you cannot connect your DVD Recorder to an A/V

receiver with a Multi-channel decoder, choose one of the

following alternatives.

Connecting to a receiver equipped with two

channel digital stereo (PCM)

● Connect one of the Recorder’s DIGITAL AUDIO

OUT jacks to the corresponding IN jack on your

receiver. Use the supplied yellow video (CVBS) cable

or an optional digital optical audio cable.

● After installation set Digital Output to PCM only (see

‘User preferences.’)

Connecting to a receiver equipped with

Dolby Pro Logic

● Make a video connection between the DVD Recorder

and the TV.

● Then connect the Recorder’s Left and Right AUDIO

OUT jacks to the corresponding inputs on the Dolby

Pro Logic Audio/Video receiver, using the audio cable

supplied (4).

● Make the appropriate Sound settings for Analog

Output in the user preferences menu.

Connecting to a TV with a Dolby Pro Logic

decoder

● Connect the Recorder to the TV as described in

chapter ‘Connecting to a TV.’

Connecting to a receiver with two channel

analog stereo

● If you have a receiver with only two-channel analog

stereo and none of the above mentioned sound

systems, connect the Left and Right AUDIO OUT

jacks of the DVD Recorder to the corresponding

AUDIO IN jacks on your receiver, ampliﬁer or stereo

system. Use the audio cable supplied (4).

Step 4: Connecting to other

equipment (optional)

To connect other devices to the Recorder, use the

available IN jacks on the back of the Recorder.

-Set top box (cable box or satellite receiver)

-VCR

-DVD Video player

Most pre-recorded video cassettes and DVD discs are

copy protected. If you try to copy them, the

DVD Recorder display will show ‘COPY PROTECT.’

This recorder is not equipped with CBCT or C3

technology to select channels on a set top box

automatically.

Do not connect a Progressive Scan video source to the

COMPONENT VIDEO IN jacks (EXT3). The DVD

Recorder cannot record Progressive Scan video signals.

Do not connect the Recorder to a VCR, then connect the

VCR directly to the TV. If you are not using the DVD

Recorder, turn off its power to avoid interfering with VCR

playback.

AMPLIFIER

Apparatus Claims of U. S. Patent Nos.

4,631,603, 4,577,216, 4,819,098, and 4,907,093

licensed for limited viewing uses only.

COMPONENT VIDEO PROG

SCAN

EXT 2

EXT 3 EXT 3

EXT 1 EXT 1/2

Apparatus Claims of U. S. Patent Nos.

4,631,603, 4,577,216, 4,819,098, and 4,907,093

licensed for limited viewing uses only.

COMPONENT VIDEO PROG

SCAN

EXT 2

EXT 3 EXT 3

EXT 1 EXT 1/2

RC 6

Set top box

3 4

6 INSTALLATION

Step 5: Connections - Front of

your DVD Recorder (optional)

Video camera connection

● If you have a DV or Digital 8 video camera, connect

the i-link DV input jack on the Recorder (1) to the

corresponding output jack on the video camera using

the i-link cable of your video camera.

This connection enables digital recording from the

following devices:

–DV or Digital 8 video camera

– Digital video deck

–Personal computer with DV output

–DVD recorder with DV output

● If you have a Hi-8 or S-VHS(C) video camera, connect

the DVD Recorder’s S-VIDEO IN jack to the

corresponding OUT jack on the video camera. Use

the S-Video cable supplied (2).Then connect the

AUDIO Left (white) and Right (red) IN jacks of the

DVD Recorder to the corresponding OUT jacks on

the video camera using the AUDIO cable supplied (4).

● Otherwise, connect the VIDEO IN jack on the

DVD Recorder (yellow) to the corresponding OUT

jack on the video camera. Use the video cable

supplied (3). Then connect the AUDIO Left (white)

and Right (red) IN jacks of the DVD Recorder to the

corresponding OUT jacks on the video camera using

the AUDIO cable supplied (4).

● If your video camera has mono sound, use only the

left audio connector. In this case the sound will be

recorded on both audio channels.

Notes

You will need only one video connection and one audio

connection: only the i-link DV connection carries both video and

audio. You may not use all the jacks on the DVD Recorder.

Step 6: Power supply

● Make sure all necessary connections are made before

connecting the DVD Recorder to the power supply.

● Plug the supplied power cable into the Power jack on

the back of the Recorder.

● Connect the power cord to an AC outlet.

Note:

Make sure the local power voltage matches the required 110V.

When the Recorder is in the ‘standby/power off ’ position,

it is still consuming some power. If you wish to disconnect your

DVD Recorder completely from power, remove the power cord

from the AC Outlet.

When the DVD Recorder is disconnected from the power,

TV channels and timer data usually will be stored one year.

Switching on

● Switch on the TV and the ampliﬁer, then select the

TV’s Video In channel or the channel you have chosen

for video playback

● Press STANDBY/ON to turn on the Recorder.

➤ The Recorder display lights. If you have not yet

installed your DVD Recorder, it will enter ‘Initial

setup.’ You will have to set your personal preferences.

Video camera

INSTALLATION 7

English

First time setup: Initial setup

After switching on the DVD Recorder for the very ﬁrst

time, the ‘Initial setup screen’ will appear. In initial setup,

you may have to set your preferences for some of the

Recorder features. If the initial setup screen does not

appear, your DVD Recorder has been installed already. You

may still change the preferences via the ‘installation menu.’

Note:

Preferences have to be set in the order in which the item menus

will appear on the screen.

The ‘Initial setup’ will only be concluded after the preferences

for the last item have been conﬁrmed.

If the Recorder is switched off while setting user preferences, all

preferences have to be set again after switching on the

Recorder again.

Manual setting

When a menu is displayed:

● Use w/v (down/up cursor) to go through the options

in the menu. The selected option will be highlighted in

white text.

● Use ENTER/OK to conﬁrm your selection and move

to the next menu.

The following items may be set in Initial setup:

Menu language

The DVD Recorder’s system menus will be displayed in

the language you choose.

Audio language

The sound of DVD-Video discs will be in the language you

choose, if it is available on the current disc. If not, speech

will revert to the ﬁrst spoken language on the disc. Also,

the DVD disc menu will be in the language you choose, if it

is available on the disc.

Subtitle language

The subtitles of DVD-Video discs will be in the language

you choose if it is available on the current disc. If not,

there will be no subtitles, or the subtitles will revert to the

default subtitle language on the disc.

TV Shape

You can choose:

- 16:9 if you have a wide screen (16:9) TV.

- 4:3 if you have a regular (4:3) TV. In this case you can also

choose between:

- Letterbox for a ‘wide-screen’ picture with black

bars at the top and bottom,

- Pan Scan, for a full-height picture with the sides

trimmed. If a disc has Pan Scan, the picture moves

(pans) horizontally to keep the main action on the

screen.

Initial setup

Menu language

Press OK to continue

English

Español

Français

Initial setup

Audio Language

Press OK to continue

English

Español

Français

Português

Italiano

Initial setup

Subtitle language

Press OK to continue

English

Español

Français

Português

Italiano

Initial setup

TV Shape

Press OK to continue

4:3 letterbox

4:3 panscan

16:9

8 INSTALLATION

Automatic TV Channel Search

Make sure the antenna is connected to the DVD Recorder.

See ‘Connecting to the antenna.’ Your DVD Recorder will

search for all TV channels that are available in your area.

It stores channels in the order in which they are found.

● Press ENTER/OK to conﬁrm.

➤ Automatic search and installation starts. This can

take several minutes.

➤ When Automatic search and installation is complete

‘Auto ch. search complete XXX Channels found’

appears on the TV screen.

● Press SYSTEM MENU to exit the Auto channel

programming menu.

Initial setup is now complete. You can still adjust the

settings. See ‘User preferences.’

Please wait

Auto Ch.Programming

Installation

Searching for TV channels

000 Channels found

FUNCTIONAL OVERVIEW 9

English

Functional overview

Front of recorder

DIGITAL

STANDBY/ON

- switches the Recorder On or to standby mode (off)

STANDBY indicator

- lights red when the Recorder is in standby mode; Recorder is not operable

- lights green when the Recorder is operable

Infrared remote control receiver

DISPLAY

- displays the current status of the Recorder

/ (open/close)

- opens/closes the disc tray

9 (stop)

(play)

- stops disc playback or recording

- starts disc play

REC

- recording of the selected channel

or source

- 5 search backward

- 6 search forward

REC VOLUME AUTO/MAN

- to adjust the recording volume

level automatically or manually

MANUAL

- 34to increase/decrease the

recording volume level

CHANNEL

- to select TV channels manually

When the Recorder is in monitor mode.

TITLE

- ∞ selects previous title/chapter/track/index

or beginning of current title/chapter/track/index

- § selects next title/chapter/track/index

AUDIO In (Left/Right) (CAM1/2)

- Audio left/right input jack to

connect a video camera or video

Recorder

VIDEO In (CVBS) (CAM2)

- Video input jack to connect a

video camera or video Recorder

S-VIDEO In (CAM1)

- Video input jack to connect a

video camera or video Recorder

DV (CAM3)

- Audio/Video input jack to connect a digital

video camera

Disc tray

during disc playback

10 FUNCTIONAL OVERVIEW

Back of Recorder

COMPONENT VIDEO PROG

SCAN

EXT 2

EXT 3 EXT 3

EXT 1 EXT 1/2

RC 6

Power jack

- connection to the power outlet

ANTENNA

- RF connection to antenna/cable TV signal

VIDEO (CVBS)

- 2 x OUT: for connection to a TV, receiver or amplifier with CVBS video inputs

- IN: for connecting a video source with CVBS outputs

S-VIDEO (Y/C)

- OUT: for connection to an amplifier, TV or receiver with S-Video inputs

- IN: for connecting a video source with S-Video outputs

COMPONENT VIDEO (YP

) OUT

- for connection to an amplifier, TV or receiver with component video (YP

) inputs

COMPONENT VIDEO (YP

) IN

- for connection to a source with component video (YP

) outputs

- RF connection to TV (does not carry the video output signal of the Recorder)

PROG SCAN (Progressive Scan)

- for connection to a TV with progressive scan (480p) input

AUDIO OUT L/R

connection to an amplifier, receiver, stereo system or to a TV

AUDIO IN L/R

- connection to the audio output of a video source of which the video output is

connected to the rear CVBS video input (EXT2) or to the rear S-Video input (EXT 1)

OUT OPTICAL

- connection to an amplifier, receiver or stereo system

with a digital (optical) audio input

OUT COAX (coaxial)

- connection to an amplifier, receiver or stereo system

with a digital (coaxial) audio input

AUDIO OUT L/R

- connection to an amplifier, receiver, stereo system or a TV

AUDIO IN L/R

- connection to the audio output of a video source of which the video output

is connected to the component video input (EXT 3)

IN RC6

- for connection to a media control system

VENTILATION OPENINGS

- allow the DVD Recorder to cool. Do not block the vents. Leave at least one inch

space free around the vents

FUNCTIONAL OVERVIEW 11

English

Display

PCMDTSDIGITALMPEG

SP EP+

MONITOR

CHANNEL

DVD CDVRW

TITLE TRACK

CHAPTER TOTAL TIME REMAINTRACK

MANUAL

TIMER

SAP

-30-40 -10-20 0 OVER-30-40 -10-20 0 OVER

STEREO

RECORD

DVD

- DVD Video disc inserted

DVD+RW

- DVD+Rewritable disc inserted

DVD+R

- DVD+Recordable disc inserted

TITLE

- Current DVD title number

TRACK

- Current VCD/CD track number

VCD

- Video CD inserted

- Audio CD inserted

SVCD

- Super Video CD inserted

HQ - SP+ - EP - EP+

- Selected recording mode: High Quality,

Standard Play Plus, Extended Play or Extended

Play Plus

CHAPTER

- DVD chapter number

STEREO

- The current channel is broadcasting

in stereo

SAP

- A second audio program is available

on the current channel

dB scale

- indicates recording volume when

using manual controls

Disc bar

- Displays disc content, recording level or

formatting progress

MANUAL

- Appears when you manually adjust the

recording level

MPEG - DIGITAL - DTS - PCM

- Active audio format

CHANNEL

- Current channel number

RECORD

- Recording in progress

TIMER

- A Timer is programmed or active

TRACK TIME

- Track time in minutes and seconds

TOTAL TIME

- Total playback time in hours,

minutes and seconds

TIME REMAIN

- Total remaining recording time in hours,

minutes and seconds

- Remote Control command received

12 FUNCTIONAL OVERVIEW

Remote control

MONITOR

- switches between disc mode and

monitor mode

STOP

- stop playback or recording

0 REC

- direct recording of the currently

selected program channel

PLAY

- begin disc playback

SEARCH/SLOW

- search backward on a disc during

playback

PAUSE

- pause playback or recording,

press repeatedly for step-by-step

disc playback

SEARCH/SLOW

- search forward on a disc during

playback

SKIP

- select a previous chapter, track

or title

EDIT

- displays edit menu for DVD+RW

or DVD+R disc

SKIP

- skip to next chapter, track or

title

VOL +/–

- TV volume up/down

MUTE

- TV Mute ON/OFF

CH +/–

- change channel up/down

ZOOM

- enlarge video image on a DVD

ANGLE

- select DVD camera angle on a

DVD

SUBTITLE

- select subtitle language on a DVD

AUDIO

- select audio language on a DVD

POWER ( )

TOP MENU

- displays DVD disc menu or Index

Picture Screen for a DVD+RW

SYSTEM MENU

- displays Recorder system menu bar

wvt u

- move cursor down/up/left/right

RETURN

- go back to previous menu step

CLEAR

- delete last entry/clear a timer

TIMER

- displays the timer menu

SELECT

- switches between different values

in a menu

ENTER/OK

- acknowledge menu selection

0-9

- numerical buttons to enter

information or select channels

TITLE/CHAP

- select title

- select chapter

A/CH (Alternate Channel)

- switches to previous TV channel

TV SHIFT

- press and hold while using other

remote control buttons to work

the TV

DIMMER

- changes the brightness of the

display

REPEAT

- repeat chapter, track, title, disc

A-B

- repeat a specific sequence

SCAN

SHUFFLE

- play the first 10 seconds of each

REC MODE

- switches recording modes

chapter within a title (DVD) or the

first 10 seconds of each track on

disc (VCD/CD) or each Title on a

DVD+RW / DVD+R

- switches the Recorder On or

to standby mode (off)

- play tracks in random order

OPERATION 13

English

Operation

Important notes for operation

You can switch on the DVD Recorder with the

STANDBY/ON button on the front of the Recorder or

POWER (B/I) button on the remote control to

interrupt a function. Keep your DVD Recorder connected

to the power outlet at all times to ensure programmed

recordings can be made.

Notes:

- Never turn the recorder on right after connecting the power

jack to a wall outlet, while the STANDBY indicator lights green.

Wait until the indicator turns red.

- When you switch off the DVD Recorder, the display will brieﬂy

show ‘WAIT.’

Loading discs

1 Press / on the front of the Recorder. The disc tray

opens.

2 Lay your chosen disc in the tray, label side up. If the

disc is two side, make sure the side you want to play is

facing up.

Make sure it is sitting properly in the correct recess.

3 Press / to close the tray.

➤ ‘READING’ appears on the Recorder display. If the

disc is pre-recorded or erase-protected, playback will

start automatically.

You can unload a disc by pressing / again or by pressing

and holding 9 for two seconds.

Note:

If ‘Child Lock’ is ‘On’ and the disc inserted is not in the ‘child

safe’ list (not authorized), the PIN code must be entered and/or

the disc has to be authorized. (see ‘Access control’)

Disc types

You will recognize the different types of discs that can be

used in your DVD Recorder by the logo. Depending on

the disc type you can either use it for recording and

playback or playback only. Some discs are not suitable to

be used in the DVD Recorder at all.

The following information summarizes existing disc types

and their DVD Recorder compatibility.

Discs for recording and playing:

DVD+RW

Records and plays. In case of a new blank disc, after the

ﬁrst recording, some more time (up to two minutes) is

needed by the Recorder to automatically make the disc

compatible with DVD video players.

DVD+R

Records and plays.

Discs for playing only:

DVD-Video

DVD-R (DVD-Recordable)

These play only if they contain DVD-Video.

DVD-RW

Plays only if it is recorded in Video mode and has been

ﬁnalized.

14 OPERATION

CD Digital Audio

You can play digital audio CDs in conventional style

through a stereo system, using the buttons on the remote

control and/or front panel of the DVD Recorder.

Super Audio CD

Of hybrid SACD discs, the CD layer can play.

(Super) Video CD

Depending on the material on the disc (a movie, video

clips, a drama series, etc.), these discs may have one or

more tracks. Tracks may have one or more indexes as

indicated on the disc case. To make access easy and

convenient, your Recorder lets you move between tracks

and indexes.

CD-R (Recordable) / CD-RW (Rewritable)

These play only if it contain Audio CD material.

Discs unsuitable for recording or playing:

DVD-RAM

DVD-Audio

On-screen display information

System menu bar

Access the system menu bar by pressing any of the

following buttons on the remote control: SYSTEM

MENU, TITLE/CHAP, ANGLE, SUBTITLE, AUDIO

and ZOOM.

Widescreen (16:9) TV sets may show only part of the

system menu bar in certain screen modes. Select a

different screen mode on the TV to see the full menu.

A number of Recorder functions can be controlled via the

system menu bar. You can move between the two parts of

the system menu bar with t (left cursor) and u (right

cursor).

Note:

Certain televisions may not show the entire DRX-1 menu on

the TV screen. If the upper or top portion of the Recorder’s

menu is not displayed properly, this is a TV-related issue and is

not an improper functioning of the DRX-1.

System menu bar icons

Part 1 Part 2

User preferences d Sound

W Current Title/Track Step motion

X Current Chapter/Index H Slow motion

Y Audio language 6 Fast motion

Z Subtitle language Time search

Angle

a Zoom

Recordable

ReWritable

OPERATION 15

English

Temporary feedback icons

These symbols may appear in the top left corner of the TV

screen when you access a feature.

Scan ﬁrst 10 seconds of each Chapter/Track

Repeat entire Disc

Repeat current Title

Repeat current Track

Repeat current Chapter

Point A for Repeat A-B playback is set.

Repeat A-B playback

Alternate camera Angle

Child Lock On

Child Safe

Resume

Action prohibited

User preference menu operation

1 Press SYSTEM MENU on the remote control.

2 Press t (left cursor) to select in the system menu

bar, then press w (down cursor).

➤ The user preference menu appears.

3 Use t/u/v/w (left/right/up/down cursor) to move

through the menus, sub menus and sub menu options.

➤ When a menu item is selected, the cursor buttons

(on the remote control) to operate the item are

displayed next to the item.

4 Press ENTER/OK, repeatedly if necessary, to con-

ﬁrm and return to the main menu.

The following functions can be operated in the user

preference menu:

User preference menu icons

Picture settings

Sound settings

Language settings

Feature settings

Remote control settings

Record settings

Installation

● Press SYSTEM MENU to remove the system menu

bar from the screen.

-- --- off on off

16 OPERATION

Status box

The status box displays the current status of the Recorder

and information about the current disc, including disc type,

total playing time, and elapsed playing time. Set status Box

to ‘On,’ if you want to see following icons when you access

a feature.

Disc type icons

DVD+RW (Rewritable)

DVD+R

DVD-Video

Super Video-CD

Video-CD

no disc

disc error

Disc status icons

recording

stop

playing

pause play

record pause

erasing

fast forward

fast reverse

slow motion

Warning box

A warning box will be displayed near the bottom on the

screen when appropriate. For instance: ‘Disc locked’

Tuner info box

The tuner info box appears at the bottom left of the TV

screen during monitor mode (see ‘Manual recording -

Checking input’). It displays the currently selected signal,

or which device you are viewing or recording from. When

TV channel is selected, it shows the channel number and/

or channel name. For example, if the tuner info box shows

EXT 1, you are viewing or recording the material that is

playing on the equipment that is connected to the EXT 1

AUDIO and VIDEO IN jacks on the back of the Recorder.

Current TV channel

No signal

Make sure you have connected an antenna or cable signal

to the ANTENNA jack on the Recorder as described in

“Installation - Update/Re-install TV channels.” If you have

selected an external input, make sure the source device is

connected and switched on.

Copy-protected signal

The tuner info box appears on the screen at all times if

you are watching TV channels through the Recorder (press

MONITOR on the remote control).

;

0 ;

012

Sidan laddas ...

Yamaha DRX-1 Användarmanual

varumärke: Yamaha

Modell: DRX-1

Kategori: DVD-spelare

Typ: Användarmanual

Denna manual är också lämplig för

DRX1

Ladda ner pdf

Rapportera

på andra språk

italiano: Yamaha DRX-1 Manuale utente
čeština: Yamaha DRX-1 Uživatelský manuál
español: Yamaha DRX-1 Manual de usuario
Deutsch: Yamaha DRX-1 Benutzerhandbuch
polski: Yamaha DRX-1 Instrukcja obsługi
português: Yamaha DRX-1 Manual do usuário
français: Yamaha DRX-1 Manuel utilisateur
Türkçe: Yamaha DRX-1 Kullanım kılavuzu
English: Yamaha DRX-1 User manual
dansk: Yamaha DRX-1 Brugermanual
русский: Yamaha DRX-1 Руководство пользователя
suomi: Yamaha DRX-1 Ohjekirja
Nederlands: Yamaha DRX-1 Handleiding
română: Yamaha DRX-1 Manual de utilizare

Yamaha DRX-1 Användarmanual

Denna manual är också lämplig för

Yamaha DRX-1 Användarmanual

på andra språk

Relaterade papper

Andra dokument