HP LaserJet 9000 Multifunction Printer series Snabbstartsguide

Q2622-90904

*Q2622-90904*

hp LaserJet 9000mfp

hp LaserJet 9000Lmfp

innføring

start

inledning

start

aloitus

Hewlett-Packard Company

printed in Germany

©

www.hp.com/support/lj9000

hp LaserJet 9000mfp hp LaserJet 9000Lmfp

printed on recycled paper

Spine = 13 mm

English

hp LaserJet 9000mfp

hp LaserJet 9000Lmfp

Start

Hewlett-Packard Company

11311 Chinden Boulevard

Boise, Idaho 83714 U.S.A.

Company 2002

Reproduction, adaptation, or

translation without prior written

permission is prohibited, except

as allowed under the copyright

laws.

Publication number

Q2622-90904

Edition 1, 12/2002

Warranty

The information contained in

this document is subject to

change without notice.

Hewlett-Packard makes no

warranty of any kind with

respect to this information.

HEWLETT-PACKARD

SPECIFICALLY DISCLAIMS

THE IMPLIED WARRANTY OF

MERCHANTABILITY AND

FITNESS FOR A PARTICULAR

PURPOSE.

Hewlett-Packard shall not be

liable for any direct, indirect,

incidental, consequential, or

other damage alleged in

connection with the furnishing or

use of this information.

Trademark Credits

Microsoft



, MS Windows



,

Windows



, Windows NT



,

Windows Me



, and Windows

XP



are U.S. registered

trademarks of Microsoft

Corporation.

All other products mentioned

herein may be trademarks of

their respective companies.

ENWW

Contents 3

English

Product Setup

Contents

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Where to look for information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Installation checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Prepare product location. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Check package contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Remove internal packaging. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Identify product parts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Position the product. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Install the print cartridge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Install accessories. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Load trays 1, 2, 3, and 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Change the control panel overlays . . . . . . . . . . . . . . . . . . . . . . . . 22

Connect product cables. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Connect power cords. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Configure the control panel display language . . . . . . . . . . . . . . . . 28

Configure digital sending. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Print the configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Install software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Installing Windows printing software . . . . . . . . . . . . . . . . . . 32

Installing Macintosh printing software . . . . . . . . . . . . . . . . . 33

Verify product setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Customer support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Warranty and regulatory information. . . . . . . . . . . . . . . . . . . . . . . 37

Hewlett-Packard limited warranty statement . . . . . . . . . . . . 37

Limited warranty for print cartridge life. . . . . . . . . . . . . . . . . 39

HP software license terms. . . . . . . . . . . . . . . . . . . . . . . . . . 40

FCC regulations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Safety information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Declaration of Conformity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

4 Product Setup

ENWW

Introduction

Congratulations on your purchase of the HP LaserJet 9000mfp*

(product number C8523A) or HP LaserJet 9000Lmfp (product number

Q2622A). The product comes standard with:

•

128 MB random access memory (RAM)

•

copying, digital sending, and wide-format printing capabilities

•

wide-format printing

•

two 500-sheet trays (Tray 2 and Tray 3)

•

a 100-sheet multipurpose tray (Tray 1)

•

a 2000-sheet input tray (Tray 4)

•

an HP Jetdirect print server

•

a duplex printing accessory (for printing on both sides of paper)

The product features an interactive touch screen on the control panel

graphical display. You must choose one of the three paper handling

devices: the 3000-sheet stacker, the 3000-sheet stapler/stacker, or

the multifunction finisher.

Note The product requires an optional token ring card to connect to a token

ring network.

*Multifunction Peripheral

ENWW

Where to look for information 5

English

Where to look for information

Start guide

This guide contains information about

unpacking and installing your product.

Introduce guide

This guide contains information about

performing basic copying, sending, and

printing tasks. Introduce is available on

the CD-ROM that came with the

product. If you would like a hard copy,

use your product to print the introduce

guide.

Use guide

This guide contains detailed information

about using and troubleshooting and is

available on the World Wide Web at

http://www.hp.com/support/lj9000. If you

would like a hard copy, use your product

to print the use guide.

6 Product Setup

ENWW

Installation checklist

This guide will help you set up and install your new product. For

proper installation, please complete each section in order.

WARNING! To avoid injury, do not attempt to lift the product. The product has been

designed to roll on wheels.

•

Unpack the product steps 1 through 5

•

Install the product steps 6 through14

•

Install printing software step 15

•

Verify product setup step 16

ENWW

Prepare product location 7

English

Step 1 Prepare product location

Product size

Prepare a location for the product that allows for these physical and

environmental requirements:

HP LaserJet 9000mfp dimensions (top and side views)

762 mm (30 in)

529.6 mm

(20.5 in)

641.4 mm

(25.3 in)

1219.2 mm (48.0 in)

508 mm

(20 in)

1177.3 mm

(46.0 in)

641.4 mm

(25.3 in)

635.0 mm

(25.0 in)

635.0 mm

(25.0 in)

647.7 mm

(25.5 in)

5

3

1

.

1

m

(

2

1

.

5

i

n

)

8 Product Setup

ENWW

Location requirements for the product

•

A level area on the floor.

•

Space allowance around the

product.

•

A well-ventilated room.

•

No exposure to direct

sunlight or chemicals,

including ammonia-based

cleaning solutions.

•

Adequate power supply

(15 A, 110 V, or 220 V circuit

located near the product). A

dedicated 15 A circuit is

recommended.

•

A stable environment—no

abrupt temperature or

humidity changes.

•

Relative humidity 20

percent to 80 percent.

•

Room temperature 10° C to

32.5° C (50° F to 91° F).

ENWW

Check package contents 9

English

Step 2 Check package contents

Package contents

power cords

MFP product

control panel overlays

print cartridge

product software

CD-ROM

Start guide

ADF output

high speed copy connect cable

standoffs

Quick Reference Poster

10 Product Setup

ENWW

Step 3 Remove internal packaging

1 To remove the product from the box, follow the instructions

printed on the box.

WARNING! This product weighs approximately 143.2 kg (315 lb). HP recommends

that the product be rolled on its wheels rather than be lifted.

2 Remove the orange shipping lock from the exterior of the product,

and remove any cardboard or styrofoam material that is not

orange.

3 Remove the protective film from the control panel graphical

display. (See Step 4, “Identify product parts.”)

4 Open the left door and remove the two packing fuser assembly

spacers. Orange tape connects fuser assembly spacers to the

outside of the left door. Remove the orange tape that runs from

the fuser assembly shipping locks to the outside of the door.

Close the door after removing the fuser assembly spacers and

the tape.

5 Open each tray, remove the orange shipping locks and any other

orange packing material, and then close the trays.

6 Remove all orange packing material and any orange tape from

the automatic document feeder (ADF) door.

7 Remove all orange packing material and any orange tape from

the glass.

Note Save all packing material. You might need it to repack the product at

another time.

ENWW

Identify product parts 11

English

Step 4 Identify product parts

The following illustrations show the location and names of the primary product parts.

Product parts (front and back views)

1

5

7

3

4

2

12

13

16

17

8

18

10

11

19

20

15

14

9

6

21

22

1 ADF output

2 Control panel

3 Front door

4 Power button

5 Tray 2

6 Tray 3

7 Left door

8 Power-cord connector

9 Tray 4 power-cord

connector

10 ADF door

11 ADF

12 Tray 1

13 Right door

14 Transfer door

15 Tray 4

16 High speed copy

connect connector

17 Parallel connector

18 Foreign interface

harness connector

(AUX)

19 HP Fast InfraRed

Connect (FIR)

20 HP JetLink connector

(Accessory)

21 EIO slot

22 HP Jetdirect printer

server connector

12 Product Setup

ENWW

Step 5 Position the product

1 Unlock the front wheels of the

product, and roll the product to its

permanent location. Leave space to

walk behind the product.

2 Push the locking tabs on the front

wheels to the lock position. Only the

front wheels lock.

3 Locate the bag with the standoffs,

and then attach them to the product.

Note

The standoffs ensure that your product

cannot be pushed up against the wall.

1

2

3

ENWW

Position the product 13

English

4 Move the scanner carriage shipping

lock to the right.

5 Attach the ADF output.

4

5

14 Product Setup

ENWW

Step 6 Install the print cartridge

Note If you get toner on your clothing, wipe it off with a dry cloth and wash

the clothing in cold water. Hot water sets toner into fabric.

1 Before removing the print cartridge

from its packaging, set the print

cartridge on a sturdy surface. Gently

slide the print cartridge out of the

packaging.

CAUTION

To prevent damage to the print cartridge,

use two hands when handling the

cartridge.

2 Open the front door of the product.

3 Rotate the green lever downward to

the unlock position.

4 Hold the cartridge so that the arrow

is on the left side of the cartridge.

Position the cartridge as shown, with

the arrow on the left side pointing

toward the product, and align the

cartridge with the printing guides.

Slide the cartridge into the product

as far as it will go.

Note

The print cartridge has an internal pull

tab. The product automatically removes

the pull tab after the print cartridge is

installed.

1

4

3

2

ENWW

Install the print cartridge 15

English

5 Press the button on the green lever,

and turn the lever clockwise to the

lock position.

6 Close the front door.

5

6

16 Product Setup

ENWW

Step 7 Install accessories

Install the accessories that you purchased. Use the installation

instructions that are packaged with the paper-handling accessories.

See Step 10, “Connect product cables,” for information on connecting

the HP Fast InfraRed connect.

.

Accessories

Note See the online use guide for information about ordering accessories.

HP Fast InfraRed

connect (FIR)

3000-sheet stapler/stacker

3000-sheet stacker

Multifunction finisher

ENWW

Load trays 1, 2, 3, and 4 17

English

Step 8 Load trays 1, 2, 3, and 4

This section describes how to load A4-

or Letter-size paper. For instructions on

loading and configuring other sizes and

types of media, see the introduce guide

that came on the CD-ROM.

CAUTION

To avoid a jam, never open a tray while

the product is printing from that tray.

To load Tray 1

Tray 1 is a multipurpose tray that holds

up to 100 sheets of standard-size paper

or 10 envelopes. The product will pull

paper from Tray 1 first (default tray). See

the use guide for information about how

to change this default.

Tray 1 provides a convenient way to print

envelopes, transparencies, custom-size

paper, or other types of media without

having to unload the other trays.

1 Open Tray 1.

2 Load A4- or Letter-size paper with

the long edge leading into the

product.

3 Adjust the paper guides so that they

lightly touch the paper stack, but do

not bend the paper.

Note

Make sure the paper fits under the tabs

on the guides and not above the load

level indicators.

2

1

2

3

18 Product Setup

ENWW

To load Tray 2 and Tray 3

1 Pull Tray 2 open until it stops.

2 Load about 100 sheets of A4- or

Letter-size paper with the short edge

of the paper leading into the product.

Note

For single-sided printing of letterhead or

preprinted paper, the side to be printed

on should be down. For double-sided

printing of letterhead or preprinted

paper, the first side to be printed on

should be up.

3 Adjust the left (Y) paper guide by

squeezing the tab on the guide and

sliding it to the mark for A4- or

Letter-size paper.

2

3

1

Sidan laddas ...

HP LaserJet 9000 Multifunction Printer series Snabbstartsguide

Denna manual är också lämplig för

HP LaserJet 9000 Multifunction Printer series Snabbstartsguide

på andra språk

Relaterade papper

Andra dokument