Motorola TALKABOUT T92 H2O Bruksanvisning

TALKABOUT

T92 H2O

OWNER'S MANUAL

hu-HU pl-PL

nl-NL

fi-FI sv-SE

nb-NO

ru-RU

pt-PT

uk-UA

it-IT

tr-TR

en-US da-DK de-DE es-ES fr-FR

1

English

RF ENERGY EXPOSURE AND PRODUCT

SAFETY GUIDE FOR PORTABLE TWO-

WAY RADIOS

ATTENTION!

Before using this product, read the RF Energy Exposure and

Product Safety Guide that ships with the radio which contains

instructions for safe usage and RF energy awareness and

control for compliance with applicable standards and regulation.

Package Contents

• 2 x TALKABOUT T92 H20 Radio

• 2 x Whistle Belt Clip

• 2 x Power Supply

• 2 x Rechargeable 800mAh NiMH battery pack

• TALKABOUT T92 H20 Manual

Frequency Chart

Note: *Only Channels one to eight are available by default.

Channels 9 to 16 need to be activated by user before

they can be selected. Channels 9 to 16 should be

used in countries where these frequencies are

allowed by government authorities. Channels 9 to 16

are not allowed in Russia.

Features and Specifications

• 8 PMR Channels. User expandable to 16 Channels in

countries where allowed by government authorities

• 121 Sub-Codes (38 CTCSS Codes & 83 DCS codes)

• Up to 10 km Range*

• VOX

• Flashlight with WHITE and RED LED

• 20 Selectable Call Tone Alerts

• Backlit LCD Display

• Roger Beep

• Micro USB Connector for charging

• Battery Level Meter

• Channel Monitor

• Channel Scan

• Dual Channel Monitor

• Keypad Lock

• Auto Squelch Control

• Auto Repeat (Scrolling)

• Battery Low Alert

• Battery Low Sleep

• Tone (On/Off)

• Silent Mode (Vibrate Alert)

• Emergency Features

• Water-Activated Flashlight

• IP Rating: IP67

• Power Source: NiMH battery Pack / 3 x AA Alkaline batteries

• Battery Life: 16 Hours (under typical use conditions)

* Range may vary depending on environmental and/or

topographical conditions.

Maintenance

This radio is waterproof to IP-67 standards. It will withstand

submersion up to 1 meter of water for up to 30 minutes, only

when the battery cover and headset accessory port are sealed.

Open the battery compartment door or headset port cover only

when the radio is dry. Installation of batteries and accessories

should be in dry environments only. Ensure battery

compartment and accessory port seals are free of all dirt and

debris. To maintain audio quality, if the radio has been

submerged in water, shake the radio briskly to remove water

trapped inside the speaker grille and microphone port. It is

recommended to rinse the radio with fresh water if it has been

exposed to salt water to preserve the life of the radio.

The charging base and AC adaptor are not waterproof. Do not

expose the charger to rain or snow. Charge the radios only in a

dry location. Do not place wet radios into the charging base.

WARNING: This radio floats with the included NiMH battery

(800mAh). It may not float with other batteries.

Channel Frequency

(MHz)

Channel Frequency

(MHz)

Channel Frequency

(MHz)

1 446.00625 7 446.08125 13 446.15625

2 446.01875 8 446.09375 14 446.16875

3 446.03125 9 446.10625 15 446.18125

4 446.04375 10 446.11875 16 446.19375

5 446.05625 11 446.13125

6 446.06875 12 446.14375

MN002243A01_.book Page 1 Tuesday, March 20, 2018 5:27 PM

English

2

Control and Functions

Antenna

Flashlight Button

Screen

PTT Button

Power Button

Menu/Lock

Microphone

Scan/Monitor

Call Tone

Volume/Scroll

Micro-USB

Charging Port

Emergency

Button

Accessory Port

Flashlight LED

Water Sensors

Speaker

MN002243A01_.book Page 2 Tuesday, March 20, 2018 5:27 PM

3

English

Display

Installing the Batteries

Each radio can either use a one NiMH rechargeable battery

pack or three units of AA Alkaline Battery.

Installing the NiMH Rechargeable Battery Pack

1. Make sure your radio is turned OFF.

2. With the back of the radio facing you, loosen the retaining

screw on the battery door and open the cover.

3. Remove the NiMH battery pack from the clear plastic bag

(do not disassemble or unwrap the battery pack).

4. Insert the NiMH battery pack with the diagram facing you.

(The ribbon should be underneath the battery pack and

should wrap around the right side of the pack for easy

removal).

5. Close the battery cover and tighten the retaining screw on

the battery door.

Installing the Three AA Alkaline Batteries

1. Make sure your radio is turned OFF.

2. With the back of the radio facing you, lift the battery cover

latch up and remove the cover.

3. Insert the three AA Alkaline batteries with (+) and (-) polarity

as shown inside. (The ribbon should be underneath the AA

alkaline batteries and wrap around the right side of the

batteries).

4. Close the battery cover and tighten the retaining screw on

the battery cover.

Removing the Batteries

Removing the NiMH Battery Pack

1. Make sure your radio is turned OFF.

2. With the back of the radio facing you, loosen the retaining

screw on the battery door and open the cover.

3. Remove the NiMH battery pack by pulling the ribbon.

4. Close the battery cover and tighten the retaining screw on

the battery door.

Removing the Three AA Alkaline Batteries

1. Make sure your radio is turned OFF.

2. With the back of the radio facing you, loosen the retaining

screw on the battery door and open the cover.

1. Channel Indicator

2. Receive and Transmit

Indicator

3. Mute [when speaker

volume is set as 0]

4. Dual Channel Monitor

[ON/OFF]

5. Scan Indicator

6. Key Lock Indicator

7. Battery Indicator [3

Battery Levels]

8. Keypad Tone [ON/OFF]

9. Silent Mode (Vibrate

Alert) [ON/OFF]

10. Roger Tone (ON/OFF)

11. Call Tone [1–20]

12. iVOX [OFF, L1, L2,

L3]; VOX [L1, L2, L3]

13. Interference Eliminator

Code [1–121]

2

3

4

5

1

6

7

8

9

11

12

13

10

MN002243A01_.book Page 3 Tuesday, March 20, 2018 5:27 PM

English

4

3. Gently remove each alkaline battery by easing each battery

out individually.

4. Close the battery cover and tighten the retaining screw on

the battery door.

Note: Exercise care when removing NiMH or AA batteries.

Do not use sharp or conductive tools to remove

either of these batteries.

Ensure radio is fully dry before installing and

removing batteries. The battery compartment seal

should be free from dirt or debris before attaching

the battery door.

Remove the batteries before storing your radio for an

extended period of time. Batteries corrode over time

and may cause permanent damage to your radio.

Radio Battery Meter

The Radio Battery icon shows the battery charge level from full

to empty . When the radio has one segment left,

the radio beeps periodically or after releasing the PTT button

(Low Battery Alert).

Battery Capacity Maintenance

1. Charge the NiMH batteries once every three months when

not in use.

2. Remove the battery from the radio after using for storage

purposes.

3. Store the NiMH batteries in a temperature between -20 °C to

35 °C and in low humidity. Avoid damp conditions and

corrosive materials.

Using the Micro-USB Charger

The micro-USB charger is a handy port that allows you to

conveniently charge your NiMH battery pack.

1. Make sure your radio is turned OFF

2. Plug the micro-USB cable into the micro-USB charging port

on your radio. Connect the other end of the micro-USB

charger to wall power outlet.

3. An empty battery will be fully charged in eight hours.

4. The battery meter bar will move when the battery is

charging.

Note: When moving between hot and cold temperatures,

do not charge the NiMH battery pack until the

temperature acclimates (usually about twenty

minutes).

For optimal battery life, remove the radio from the

charger within sixteen hours. Do not store the radio

while connected to the charger.

Attaching and Removing the Belt Clip

1. Attach the belt clip to the TALKABOUT plate at the back of

the radio until the clip clicks in place.

2. Attach the belt clip to pocket or belt strap until the clip clicks

in place.

To Remove

1. Push the release tab on top of the belt clip to release the

latch.

2. Pull the belt clip away from the back of the radio.

Turning your Radio On and Off

Press and hold the Power button to turn the radio ON or

OFF.

1. In the ON position, the radio chirps and briefly shows all

feature icons available on the radio.

2. The display screen then shows the current channel, code

and all features that are enabled.

Setting the Volume

From Standby Mode, press on either or to show the

current value. Press or again to adjust the volume

setting.

1. Press to increase the speaker volume.

2. Press to decrease the speaker volume.

Do not hold the radio close to your ear. If the volume is set to an

uncomfortable level, it could hurt your ear.

Adjust ‘0’ to mute the speaker.

MN002243A01_.book Page 4 Tuesday, March 20, 2018 5:27 PM

5

English

Talking and Listening

All radios in your group must be set to the same channel and

Interference Eliminator Code in order to communicate.

1. Hold your radio 5–8 cm from your mouth.

2. Press and hold the PTT button while speaking. The Transmit

icon appears on the display.

3. Release the PTT button. You can now receive incoming

calls. When you do, the Receive icon appears on the

display.

For maximum clarity, hold the radio 2 to 3 inches away and

avoid covering the microphone while talking.

Talk Range

Your radio is designed to maximize performance and improve

transmission range. Do not use the radios closer than 5 feet

apart.

Monitor Button

Pressing and holding Scan/Monitor button 3 seconds

allows you to listen to the volume level of the radio when you

are not receiving. This allows you to adjust the volume, if

necessary. You can also press Scan/Monitor button to

check the activity on your current channel before you talk.

Push-to-Talk Time-out Timer

To prevent accidental transmissions and save battery life, the

radio emits a continuous warning tone and stops transmitting if

you press the PTT button for 60 seconds continuously.

Menu options

Note: *Only Channels one to eight are available by default.

Channels 9 to 16 need to be activated by user before

they can be selected. Channels 9 to 16 should be

used in countries where these frequencies are

allowed by government authorities. Channels 9 to 16

are not allowed in Russia.

Menu Key

Two Way Mode

Channel (1-8)

Sub Code (0-121)

Call Tone (1-20)

Vibrate Alert (On/Off)

Keypad Tones (On/Off)

Talk Confirmation Tones (On/Off)

Dual Watch Channel (1-22)

Dual Watch Interference Eliminator Code

Voice Operated Transmission

(VOX) (Off, L1,L2,L3)

MN002243A01_.book Page 5 Tuesday, March 20, 2018 5:27 PM

English

6

Selecting the Channel

Your radio has eight channels. The channel is the frequency the

radio uses to transmit.

1. With the radio ON, press Menu button until the channel

number starts to flash.

2. Press or to change the channel. Long press on

these keys allows you to scroll through the channels rapidly

to browse the codes.

3. Press PTT button to exit menu or Menu button to

continue set up.

Note: Your radio has eight channels by default. In countries

where 16 channels are allowed, you can activate

Channels 9 to 16 with the following steps:

1.Press Menu until the channel number starts to flash.

2. Press and hold down and simultaneously for

three seconds until you hear a beep and “16 CH” is

displayed briefly.

Note: *Only Channels one to eight are available by default.

Channels 9 to 16 need to be activated by user before

they can be selected. Channels 9 to 16 should be

used in countries where these frequencies are

allowed by government authorities. Channels 9 to 16

are not allowed in Russia.

Selecting the Interference Eliminator Code

Interference Eliminator Codes help minimize interference by

blocking transmissions from unknown sources. Your radio has

121 Interference Eliminator Codes.

To set the code for a channel:

1. Press Menu button twice until the code “9” starts to

flash.

2. Press or to select the code. You can press or hold

to speed up scrolling through the codes.

3. Press the PTT button to exit menu or Menu button to

continue set up.

Setting and Transmitting Call Tones

Your radio can transmit different call tones to other radios in

your group so you can alert them that you want to talk. Your

radio has 20 call tones for you to choose from.

To set a call tone:

1. Press Menu button three times until Call Tone icon

appears. The current call tone setting will flash.

2. Press or to change and listen to the call tone.

3. Press the PTT button to exit menu or Menu button to

continue set up.

In order to transmit your call tone to other radios, set up the

same channel and Interference Eliminator Code on your radio

and press Call Tone button.

Voice Operated Transmission ()

Transmission is initiated by speaking into the microphone of the

radio instead of pushing the PTT button.

1. Press Menu button four times until icon

appears on the display. The current setting (L1-L3) will flash.

2. Press or to select the sensitivity level.

3. Press the PTT button to exit menu or Menu button to

continue set up.

L3 = High Sensitivity for quiet environments

L2 = Medium Sensitivity for most environments

L1 = Low Sensitivity for noisy environments

MN002243A01_.book Page 6 Tuesday, March 20, 2018 5:27 PM

7

English

Note: There is a short delay between the time you start

talking and when the radio transmits.

Dual Channel Monitor

Enables you to scan the current channel and another channel

alternately.

To set another channel and start Dual Channel:

1. Press Menu button five times until the Dual Channel

icon appears. The Dual Channel will flash.

2. Press or to select the channel then press Menu

button.

3. Press or to select the Interference Eliminator Code.

4. Press the PTT button to exit menu or Menu button to

continue set up.

5. The radio starts to Dual Channel.

Note: If you set the same channel and code as the current

channel, Dual Channel Monitor turns OFF.

Silent Mode (Vibrate Alert)

Silent Mode (Vibrate Alert) notifies you that your radio is

receiving a message. This is useful in noisy environments.

When the alert is on, the radio vibrates once every 30 seconds

when you receive a message on the channel and code you set.

1. Press Menu button seven times until Vibracall icon

is displayed. The current setting will flash.

2. Press or to change the setting to On/Off.

3. Press the PTT button to exit menu or Menu button to

continue set up.

Keypad Tones

You may enable or disable the speaker key tones. You will hear

the key tone each time a button is pushed.

1. Press Menu button eight times until Keypad Tone

icon appears. The current setting On/Off will flash.

2. Press either or to turn On/Off.

3. Press the PTT button to confirm or Menu button to

continue set up.

Note: The following are not disabled when the key tone

feature is OFF:

•Transmit time-out alert tone

•Call tone

•Low battery alert tone or

•The transmitted talk confirmation tone

Transmitting a Talk Confirmation Tone

You can set your radio to transmit a unique tone when you finish

transmitting. It is like saying “Roger” or “Over” to let others know

you have finished talking.

1. Press Menu button nine times until the Roger Tone

icon appears. The current setting On/Off flashes.

2. Press or to turn On or Off.

3. Press the PTT button to set or Menu button to continue

set up.

MN002243A01_.book Page 7 Tuesday, March 20, 2018 5:27 PM

English

8

Emergency Alert Mode

The Emergency Alert feature can be used to signal members in

your group of your need for urgent help. T92 H2O radios will

operate in an automatic “hands- free” emergency control mode

for a total of 30 seconds after activating the Emergency Alert.

T92 H2O radios in your group will automatically advance the

speaker volume to the maximum setting and sound a warbling

alert tone for 8 seconds. The alert tone is emitted from your own

radio speaker and the receiving radios in your group. After the 8

second alert, any spoken words or incidental sounds at your

end will be transmitted to the group for 22 seconds. For the 30

second duration of Emergency Alert mode, T92 H2O radio

controls and buttons will be locked to maximize reception of the

emergency message.

1. Press and hold the Emergency Alert button for 3 seconds.

2. Release the button and the alert tone begin to sound. At the

same time, it activates RED LED flash. There is no need to

continue to hold the Emergency Alert button or use PTT for

your message to be transmitted.

WARNING: The Emergency Alert feature should only be

used in the even of an actual emergency. Motorola

Solutions is not responsible if there is no response to the

emergency alert from the receiving group.

Built-in Flashlight

Press the Flashlight button to cycle between OFF, RED Light,

WHITE Light and then back to OFF again.

The Flashlight will turn off when you press the Flashlight button

if the RED Light is left on for more than 3 seconds.

The Flashlight will turn off automatically after 30 minutes of non-

activity if the battery level is below 50%.

Note: Turn off the flashlight when not in use to conserve

battery power.

Keypad Lock

To avoid accidentally changing your radio settings:

1. Press and hold Menu button until Key Lock Indicator

icon displays.

2. You can turn the radio ON and OFF, adjust the volume,

receive, transmit, and monitor channels when in the lock

mode. All other functions remain locked.

3. Press Menu button and hold until Key Lock Indicator

is no longer displayed to unlock the radio.

Scanning

Use the scan function to do the following:

• Search the eight channels for transmissions from unknown

parties.

• Find someone in your group who has accidentally changed

channels or

• To quickly find unused channels for your own use.

There is a priority feature and two modes of scanning (basic

and advanced) to make your search more effective.

• The “Basic Scan” mode uses the channel and code

combinations for each of the eight channels as you have set

them (or with the default code value of 1).

• The “Advance Scan” mode will scan all channels for any and

all codes; detect any code in use and use that code value

temporary for that channel.

• Priority is given to the “Home Channel” (i.e. the channel and

Interference Eliminator Code your radio is set to when you

start the scan). This means the initial channel (and code

settings) is scanned more often than the other seven

channels and your radio will respond quickly to any activity

occurring on the home channel as a priority.

MN002243A01_.book Page 8 Tuesday, March 20, 2018 5:27 PM

9

English

To start Basic Scanning:

1. Press the key briefly. The Scan icon will appear in

the display and the radio will begin to scroll through the

channel and code combinations.

2. When the radio detects channel activities matching the

channel and code combination, the radio will stop scrolling

and you can hear the transmission.

3. Press the PTT button within 5 minutes after the end of the

transmission to respond and talk to the person transmitting.

4. The radio will resume scrolling through the channels 5

seconds after the end of any received activity.

5. Press the Scan/Monitor button briefly to stop scanning.

To start Advanced Scanning:

To set another channel and start Dual Channel Monitor:

1. Press the Scan/Monitor button briefly. The Scan

icon will appear in the display and the radio will begin to

scroll through the channels. No Interference Eliminator

Codes will filter what is heard.

2. When the radio detects channel activities with ANY code (or

NO code), it stops scrolling and you can hear the

transmission. Any Interference Eliminator Code that may be

use by other party will be detected and displayed.

3. When you respond and talk to the person transmitting, press

the PTT button within five seconds after the end of the

transmission.

4. The radio will resume scrolling through the channels 5

seconds after the end of any received activity.

5. Press the Scan/Monitor button briefly to stop scanning.

Scanning Notes:

1. The transmission will be on the “Home Channel” if you press

the PTT button while the radio is scrolling through inactive

channels. You may press the Scan/Monitor button to

stop scanning at any time.

2. You may immediately resume the scan by briefly pressing

the or if the radio stops on an undesired

transmission.

3. You may temporarily remove that channel from the scan list

by pressing and holding or for 3 seconds if the radio

stops repeatedly on an undesired transmission. You may

remove more than one channel this way.

4. Turn the radio OFF and then turn back ON, or EXIT and re-

enter the scanning mode by pressing Scan/Monitor

button to restore and remove channel(s) to the scan list.

5. You cannot remove the “Home Channel” from the scan list.

6. In the Advanced Scan, the detected code will only be used

for one transmission. You must take note of that code, exit

scan and set the detected code on that channel to

permanently use the detected code.

Water Sensor

When the radio comes in contact with water, the WHITE LED

will begin flashing until the battery is dead. Press the Flashlight

button to turn off the flashing LED.

MN002243A01_.book Page 9 Tuesday, March 20, 2018 5:27 PM

English

10

Warranty Information

The authorized Motorola Solutions dealer or retailer where you

purchased your Motorola Solutions two-way radio and/or

original accessories will honour a warranty claim and/or provide

warranty service.

Please return your radio to your dealer or retailer to claim your

warranty service. Do not return your radio to Motorola

Solutions.

In order to be eligible to receive warranty service, you must

present your receipt of purchase or a comparable substitute

proof of purchase bearing the date of purchase. The two-way

radio should also clearly display the serial number. The

warranty will not apply if the type or serial numbers on the

product have been altered, deleted, removed, or made illegible.

What Is Not Covered By The Warranty

• Defects or damage resulting from use of the Product in other

than its normal and customary manner or by not following

the instructions in this user manual.

• Defects or damage from misuse, accident or neglect.

• Defects of damage from improper testing, operation,

maintenance, adjustment, or any alteration or modification of

any kind.

• Breakage or damage to aerials unless caused directly by

defects in material or workmanship.

• Products disassembled or repaired in such a manner as to

adversely affect performance or prevent adequate

inspection and testing to verify any warranty claim.

• Defects or damage due to range.

• Defects or damage due to moisture, liquid or spills.

• All plastic surfaces and all other externally exposed parts

that are scratched or damaged due to normal use.

• Products rented on a temporary basis.

• Periodic maintenance and repair or replacement of parts

due to normal usage, wear and tear.

Copyright Information

The Motorola Solutions products described in this manual may

include copyrighted Motorola Solutions programs, stored

semiconductor memories or other media. Laws in the United

States and other countries preserve for Motorola Solutions,

certain exclusive rights for copyrighted computer programs,

including the exclusive right to copy or reproduce in any form,

the copyrighted Motorola Solutions programs.

Accordingly, any copyrighted Motorola Solutions computer

programs contained in the Motorola Solutions products

described in this manual may not be copied or reproduced in

any manner without express written permission of Motorola

Solutions. Furthermore, the purchase of Motorola Solutions

products shall not be deemed to grant either directly or by

implication, estoppel, or otherwise, any license under the

copyrights, patents or patent applications of Motorola Solutions,

except for the normal non-exclusive royalty free license to use

that arises by operation of law in the sale of a products.

MOTOROLA, MOTO, MOTOROLA SOLUTIONS and the

Stylized M logo are trademarks or registered trademarks of

Motorola Trademark Holdings, LLC and are used under license.

All other trademarks are the property of their respective owners.

MN002243A01_.book Page 10 Tuesday, March 20, 2018 5:27 PM

1

Dansk

VEJLEDNING OM RF-

ENERGIEKSPONERING OG

PRODUKTSIKKERHED TIL BÆRBARE

TOVEJSRADIOER

OBS!

Inden brug af radioen skal du læse vejledningen om RF-

energieksponering og sikkerhed, der leveres sammen med

radioen. Vejledningen indeholder instruktioner omkring sikker

brug, opmærksomhed omkring forekomst af RF-energi og

kontrol af overholdelse med gældende standarder og

bekendtgørelser.

Pakkens indhold

• 2 x TALKABOUT T92 H20-radioer

• 2 x bælteclips med fløjte

• 2 x Strømforsyning

• 2 x genopladelig 800mAh NiMH-batteripakke

• TALKABOUT T92 H20 Brugervejledning

Frekvenstabel

Bemærk: *Kun kanal et til otte er tilgængelige som

standard. Kanal 9 til 16 skal aktiveres af

brugeren, før de kan vælges. Kanal 9 til 16 skal

anvendes i lande, hvor myndighederne tillader

brug af disse frekvenser. Kanal 9 til 16 må ikke

anvendes i Rusland.

Funktioner og specifikationer

• 8 PMR-kanaler. Kan udvides af brugeren til 16 kanaler i lande, hvor

myndighederne tillader dette

• 121 delkoder (38 CTCSS-koder & 83 DCS-koder)

• Rækkevidde* på op til 10 km

• VOX

• Lommelygte med HVIDE og RØDE indikatorer

• 20 opkaldstonealarmer, som brugeren vælger

• Baggrundsbelyst LCD-skærm

• Modtaget-bip

• Micro-USB-stik til opladning

• Batteriniveaumåler

• Kanalskærm

• Kanalscanning

• Overvågning af to kanaler

• Tastelås

• Automatisk squelch-styring

• Automatisk gentagelse (rulning)

• Advarsel om lavt batteriniveau

• Lavt batteriniveau, slumring

• Tone (til/fra)

• Tilstanden Silent (vibrationsalarm)

• Nødopkaldsfunktioner

• Vandaktiveret lommelygte

• IP-klassificering: IP67

• Strømkilde: NiMH-batteripakke / 3 x AA-alkalinebatterier

• Batteritid: 16 timer (under normale brugsforhold)

* Intervallet kan variere afhængigt af miljømæssige og/eller

topografiske forhold.

Vedligeholdelse

Denne radio er vandtæt i henhold til IP-67-standarder. Den kan

modstå nedsænkning i op til 1 meter vand i op til 30 minutter,

men kun, når batteridækslet og porten til headsettilbehøret er

forseglede. Åbn kun lugen til batterirummet og headsettets

portdæksel, når radioen er tør. Installation af batterier og

tilbehør bør kun finde sted i tørre omgivelser. Sørg for at

forseglingerne til batterirummet og tilbehørsporten er fri for

snavs og urenheder. Hvis radioen er blevet nedsænket i vand,

skal du ryste radioen hurtigt for at fjerne vand fra

højttalergitteret og mikrofonporten for at bevare lydkvaliteten.

Det anbefales at skylle radioen med rent vand, hvis den har

været udsat for saltvand, for at bevare radioens levetid.

Opladerenheden og AC-adapteren er ikke vandtætte. Udsæt

ikke opladeren for regn eller sne. Oplad kun radioer på et tørt

sted. Sæt ikke våde radioer i opladerenheden.

ADVARSEL: Denne radio kan flyde med det medfølgende

NiMH-batteri (800 mAh). Den kan ikke altid flyde med andre

batterier.

K. Frekvens

(MHz)

K. Frekvens

(MHz)

K. Frekvens

(MHz)

1 446,00625 7 446,08125 13 446,15625

2 446,01875 8 446,09375 14 446,16875

3 446,03125 9 446,10625 15 446,18125

4 446,04375 10 446,11875 16 446,19375

5 446,05625 11 446,13125

6 446,06875 12 446,14375

MN002243A01_.book Page 1 Tuesday, March 20, 2018 5:27 PM

Dansk

2

Kontrol og funktioner

Antenne

Knappen

Flashlight

Skærm

PTT-knap

Tænd/

sluk-knap

Menu/Lås

Mikrofon

Scanning/

Overvåg

Opkaldstone

Lydstyrke/Rulle

Micro-USB-

opladerport

Nødopkalds-

knap

Tilbehørsport

Indikator for

lommelygte

Vandsensorer

Højttaler

MN002243A01_.book Page 2 Tuesday, March 20, 2018 5:27 PM

3

Dansk

Skærm Installer batterierne

Hver radio kan enten bruge en genopladelig NiMH-batteripakke

eller tre AA-alkalinebatterienheder.

Installer den genopladelige NiMH-batteripakke

1. Sørg for, at radioen er slået FRA.

2. Sørg for, at radioens bagside vender ud mod dig, løsn

holdeskruen på batterilugen, og åbn dækslet.

3. Fjern den genopladelige NiMH-batteripakke fra den

gennemsigtige plastikpose (batteripakken må ikke skilles ad

eller pakkes ud).

4. Sæt NiMH-batteripakken i, så diagrammet vender ud mod

dig. (Båndet skal være under batteripakken og skal vikles

om pakkens højre side, så det nemt kan fjernes).

5. Luk batteridækslet, og stram holdeskruen på batterilugen.

Installer de tre AA-alkalinebatterier

1. Sørg for, at radioen er slået FRA.

2. Sørg for, at radioens bagside vender ud mod dig, løft

batteridækslets lås op, og fjern dækslet.

3. Sæt de tre AA-alkalinebatterier i med (+)- og (-)-polerne som

vist indeni. (Båndet skal være under AA-alkalinebatterierne

og skal vikles rundt om batteriernes højre side, så det nemt

kan fjernes).

4. Luk batteridækslet, og stram holdeskruen på batteridækslet.

Fjern batterierne

Fjern NiMH-batteripakken

1. Sørg for, at radioen er slået FRA.

2. Sørg for, at radioens bagside vender ud mod dig, løsn

holdeskruen på batterilugen, og åbn dækslet.

3. Fjern NiMH-batteripakken ved at trække i båndet.

4. Luk batteridækslet, og stram holdeskruen på batterilugen.

1. Kanalindikator

2. Indikator for send/modtag

3. Lydløs [når lydstyrken for

højttaleren er indstillet til 0]

4. Overvågning af to kanaler

[TIL/FRA]

5. Indikator for scanning

6. Indikator for tastelås

7. Batteriindikator

[3 batteriniveauer]

8. Tastaturtone [TIL/FRA]

9. Tilstanden Silent

(vibrationsalarm)

[TIL/FRA]

10. Modtaget-tone

(TIL/FRA)

11. Opkaldstone [1–20]

12. iVOX [FRA, L1, L2, L3];

VOX [L1, L2, L3]

13. Interferenseliminatorkode

[1–121]

2

3

4

5

1

6

7

8

9

11

12

13

10

MN002243A01_.book Page 3 Tuesday, March 20, 2018 5:27 PM

Dansk

4

Fjern de tre AA-alkalinebatterier

1. Sørg for, at radioen er slået FRA.

2. Sørg for, at radioens bagside vender ud mod dig, løsn

holdeskruen på batterilugen, og åbn dækslet.

3. Fjern forsigtigt hvert alkalinebatteri ved at lempe batterierne

ud enkeltvist.

4. Luk batteridækslet, og stram holdeskruen på batterilugen.

Bemærk: Udvis forsigtighed, når NiMH- og AA-batterier

fjernes. Brug ikke skarpt eller ledende værktøj til

at fjerne disse batterier.

Sørg for, at radioen er helt tør, inden du indsætter

og fjerner batterier. Forseglingen til

batterirummet skal holdes fri for snavs eller

urenheder, inden du monterer batteridækslet.

Fjern batterierne, inden radioen opbevares i en

længere periode. Batterier korroderer med tiden

og kan forårsage permanent skade på din radio.

Radioens batterimåler

Radioens batteriikon viser batteriets opladningsniveau fra fuldt

opladet til afladet . Når radioen har én bjælke

tilbage, kvidrer radioen regelmæssigt, eller efter knappen PTT

slippes (advarsel om lavt batteri).

Vedligeholdelse af batterikapacitet

1. Oplad NiMH-batterierne én gang hver tredje måned, når den

ikke er i brug.

2. Fjern batteriet fra radioen efter brug mhp. opbevaring.

3. Opbevar NiMH-batterierne i en temperatur mellem -20 °C til

35 °C og i lav luftfugtighed. Undgå fugtige forhold og

ætsende stoffer.

Brug af micro-USB-opladeren

Micro-USB-opladeren er et praktisk stik, der gør det nemt for

dig at oplade NiMH-batteripakken.

1. Sørg for, at radioen er slået FRA

2. Indsæt micro-USB-kablet i micro-USB-ladeporten på

radioen. Slut den anden ende af micro-USB-opladeren til en

stikkontakt.

3. Et tomt batteri er fuldt opladet efter otte timer.

4. Bjælken på batterimåleren flytter sig, når batteriet oplades.

Bemærk: Når der skiftes mellem varme og kolde temperaturer,

må NiMH-batteriet ikke oplades, før temperaturen

akklimatiseres (normalt ca. 20 minutter).

For at opnå den optimale batteritid, skal radioen

fjernes fra opladeren inden for 16 timer. Opbevar

ikke radioen, mens den er tilsluttet opladeren.

Påsæt og fjern bælteclipsen

1. Sæt bælteclipsen fast på TALKABOUT-pladen bag på

radioen, indtil clipsen klikker på plads.

2. Sæt bælteclipsen fast på lommen eller bæltestroppen, indtil

clipsen klikker på plads.

Sådan fjernes den

1. Skub på frigørelsestappen øverst på bælteclipsen for at

frigøre låsen.

2. Træk bælteclipsen væk fra bagsiden af radioen.

Sådan slår du radioen Til og Fra

Tryk på tænd/sluk-knappen , og hold den nede for at slå

radioen TIL eller FRA.

1. I TIL-positionen kvidrer radioen og viser kort alle de

funktionsikoner, der findes på radioen.

2. Skærmen viser så den aktuelle kanal, kode og alle

funktioner, der er aktiveret.

MN002243A01_.book Page 4 Tuesday, March 20, 2018 5:27 PM

5

Dansk

Indstilling af lydstyrken

Når radioen er i tilstanden Standby, skal du trykke på enten

eller for at vise den aktuelle kanal. Tryk igen på eller

for at indstille lydstyrken.

1. Tryk på for at øge lydstyrken for højttaleren.

2. Tryk på for at mindske lydstyrken for højttaleren.

Undgå at holde radioen tæt ved øret. Hvis lydstyrken er

indstillet til et ubehageligt niveau, kan det skade dit øre.

Indstil '0' for at sætte højttaleren på lydløs.

TALE OG LYTTE

Alle radioer i gruppen skal være indstillet til samme kanal og

interferenseliminatorkode for at kunne kommunikere.

1. Hold radioen på 5-8 cm afstand af munden.

2. Tryk på tasten PTT, og hold den nede, mens du taler. Ikonet

for transmission vises på skærmen.

3. Slip knappen PTT. Du kan nu modtage indgående opkald.

Når du gør det, vises ikonet for modtag på skærmen.

For at få den bedste lydkvalitet skal du holde radioen to til tre

tommer væk og undgå at holde for mikrofonen, mens du taler.

Rækkevidde for tale

Radioen er designet til at maksimere ydeevnen og forbedre

transmissionsrækkevidden. Brug ikke radioer, der er mindre

end fem fod fra hinanden.

Knappen Monitor

Tryk på knappen Scan/Monitor og hold den nede i tre

sekunder for at kunne høre radioens lydniveau, når du ikke

modtager. Dette giver dig mulighed for at justere lydstyrken,

hvis det er nødvendigt. Du kan også trykke på knappen

Scan/Monitor for at kontrollere aktivitet på den aktuelle kanal,

inden du taler.

Push-to-Talk Time-out timer

For at forhindre utilsigtede transmissioner og for at spare

batteritid, udsender radioen en konstant advarselstone og

standser transmissionen, hvis du trykker på knappen PTT

konstant i tres sekunder.

MN002243A01_.book Page 5 Tuesday, March 20, 2018 5:27 PM

Dansk

6

MENUINDSTILLINGER

Bemærk: *Kun kanal et til otte er tilgængelige som

standard. Kanal 9 til 16 skal aktiveres af

brugeren, før de kan vælges. Kanal 9 til 16 skal

anvendes i lande, hvor myndighederne tillader

brug af disse frekvenser. Kanal 9 til 16 må ikke

anvendes i Rusland.

Sådan vælger du en kanal

Radioen har otte kanaler. Kanalen er den frekvens, som

radioen bruger til at transmittere.

1. Når radioen er tændt, skal du trykke på knappen Menu,

indtil kanalnummeret begynder at blinke.

2. Tryk på eller for at skifte kanal. Et langt tryk på

disse taster giver dig mulighed for hurtigt at rulle igennem

kanalerne for at gennemse koderne.

3. Tryk på knappen PTT for at forlade menuen eller knappen

Menu for at forsætte opsætningen.

Bemærk: Radioen har som standard otte kanaler. I lande,

hvor 16 kanaler er tilladt, kan du aktivere kanal

9 til 16 ved at udføre følgende trin:

1. Tryk på Menu, indtil kanalnummeret begynder at

blinke.

2. Tryk samtidigt på og , og hold dem nede i tre

sekunder, indtil du hører et bip, og "16 CH" vises

kortvarigt.

Bemærk: *Kun kanal et til otte er tilgængelige som

standard. Kanal 9 til 16 skal aktiveres af

brugeren, før de kan vælges. Kanal 9 til 16 skal

anvendes i lande, hvor myndighederne tillader

brug af disse frekvenser. Kanal 9 til 16 må ikke

anvendes i Rusland.

Valg af interferenseliminatorkode

Interferenseliminatorkoder hjælper med at minimere interferens

ved at blokere transmissioner fra ukendte kilder. Radioen har

121 interferenseliminatorkoder.

Sådan angiver du koden for en kanal:

1. Tryk på knappen Menu to gange, indtil koden "9"

begynder at blinke.

Tasten Menu

Tilstanden Two Way

Kanal (1-8/*1-16)

Delkode (0-121)

Opkaldstone (1-20)

Vibrationsalarm (Til/Fra)

Tastaturtoner (Til/Fra)

Talebekræftelsestoner (Til/Fra)

Kanal til dobbelt overvågning (1-22)

Interferenseliminatorkode til dobbelt overvågning

Stemmestyret transmission

(VOX) (Fra, L1,L2,L3)

MN002243A01_.book Page 6 Tuesday, March 20, 2018 5:27 PM

7

Dansk

2. Tryk på eller for at vælge koden. Du kan trykke og

holde nede for at øge hastigheden for rulning i koder.

3. Tryk på knappen PTT for at forlade menuen eller knappen

Menu for at fortsætte opsætningen.

Indstilling og transmission af opkaldstoner

Radioen kan sende forskellige opkaldstoner til andre radioer i

gruppen, så du kan give dem besked om, at du vil tale. Radioen

har 20 opkaldstoner, som du kan vælge imellem.

Sådan indstiller du en opkaldstone:

1. Tryk på knappen Menu tre gange, indtil ikonet for

opkaldstone vises. Den aktuelle opkaldstoneindstilling

blinker.

2. Tryk på eller for at skifte og høre opkaldstonen.

3. Tryk på knappen PTT for at forlade menuen eller knappen

Menu for at fortsætte opsætningen.

For at transmittere dit opkald til andre radioer, skal du indstille

den samme kanal og interferenseliminatorkode på radioen,

og du skal trykke på knappen Call Tone.

Voice Operated Transmission ()

Transmission startes ved at tale ind i mikrofonen på radioen i

stedet for at trykke på knappen PTT.

1. Tryk på knappen Menu 4 gange, indtil ikonet

vises på skærmen. Den aktuelle indstilling (L1-L3) blinker.

2. Tryk på eller for at vælge følsomhedsniveau.

3. Tryk på knappen PTT for at forlade menuen eller knappen

Menu for at fortsætte opsætningen.

Bemærk: Der er en kort forsinkelse mellem det tidspunkt,

du begynder at tale, og det tidspunkt, hvor

radioen begynder at transmittere.

Overvågning af to kanaler

Giver dig mulighed for at scanne den aktuelle kanal og en

anden kanal skiftevis.

Sådan indstiller du en anden kanal og starter to kanaler:

1. Tryk på knappen Menu 5 gange, indtil ikonet for to

kanaler vises. To kanaler blinker.

2. Tryk på eller for at vælge kanal. Tryk derefter på

knappen Menu.

3. Tryk på eller for at vælge interferenseliminatorkode.

4. Tryk på knappen PTT for at forlade menuen eller knappen

Menu for at fortsætte opsætningen.

5. Radioen starter to kanaler.

Bemærk: Hvis du indstiller den samme kanal og kode som

den aktuelle kanal, slår Overvågning af to kanaler

FRA.

L3 = høj følsomhed til stille omgivelser

L2 = medium følsomhed til de fleste omgivelser

L1 = lav følsomhed til støjende omgivelser

MN002243A01_.book Page 7 Tuesday, March 20, 2018 5:27 PM

Dansk

8

Tilstanden Silent (vibrationsalarm)

Tilstanden Silent (vibrationsalarm) underretter dig om, at din

radio modtager en besked. Dette er nyttigt i støjende

omgivelser. Når alarmen er slået til, vibrerer radioen hvert

30. sekund, når du modtager en besked på den kanal og kode,

du har angivet.

1. Tryk på knappen Menu 7 gange, indtil ikonet for

vibrationsopkald vises. Den aktuelle indstilling blinker.

2. Tryk på eller for at skifte indstillingen til Til/Fra.

3. Tryk på knappen PTT for at forlade menuen eller knappen

Menu for at fortsætte opsætningen.

Tastaturtoner

Du kan aktivere eller deaktivere højttalerens tastaturtoner.

Du kan høre tastetonen, hver gang du trykker på en knap.

1. Tryk på knappen Menu 8 gange, indtil ikonet for

tastaturtone vises. Den aktuelle indstilling Til/Fra blinker.

2. Tryk på enten eller for at slå Til/Fra.

3. Tryk på knappen PTT for at bekræfte eller knappen

Menu for at fortsætte opsætningen.

Bemærk: Følgende deaktiveres ikke, når

tastetonefunktionen er slået FRA:

• Alarmtone for Transmit time-out

• Opkaldstone

• Tone for advarsel om lavt batteriniveau eller

• Tone for den transmitterede samtalebekræftelse

Transmission af tonen for samtalebekræftelse

Du kan indstille radioen til at transmittere en unik tone, når du er

færdig med at transmittere. Det er ligesom at sige "Modtaget"

eller "Skifter" for at lade andre vide, at du er færdig med at tale.

1. Tryk på knappen Menu 9 gange, indtil ikonet for

modtaget-tone vises. Den aktuelle indstilling Til/Fra blinker.

2. Tryk på eller for at slå Til eller Fra.

3. Tryk på knappen PTT for at indstille eller på knappen

Menu for at fortsætte opsætningen.

Tilstanden Emergency Alert

Funktionen Emergency Alert kan bruges til at signalere til

medlemmer i gruppen, at du har brug for akut hjælp. T92 H2O-

radioer kører i en automatisk "håndfri" tilstand for styring af

nødsituation i samlet 30 sekunder, efter Emergency Alert er

aktiveret. T92 H2O-radioer i gruppen flytter automatisk

højttalerlydstyrken til den maksimale indstilling og afgiver en

syngende alarmtone i 8 sekunder. Alarmtonen udsendes fra din

egen radiohøjttaler og de modtagende radioer i gruppen. Efter

alarmen på 8 sekunder vil alle talte ord eller tilfældige lyde fra

din ende blive transmitteret til gruppen i 22 sekunder. I de

30 sekunder, som tilstanden Emergency Alert varer, vil T92

H2O-radioens betjeningselementer og knapper låses for at

maksimere modtagelsen af nødmeddelelsen.

1 Tryk på knappen Emergency Alert, og hold den nede i

3 sekunder.

2. Slip knappen, og alarmtonen begynder at lyde. Samtidig

aktiverer den det RØDE indikatorblink. Du behøver ikke

fortsætte med at holde knappen Emergensy Alert nede eller

bruge PTT for at transmittere din besked.

ADVARSEL: Funktionen Emergency Alert må kun bruges i

tilfælde af en virkelig nødsituation. Motorola Solutions er

ikke ansvarlig, hvis der ikke sker reaktion fra

modtagergruppen på nødsituationsalarmen.

MN002243A01_.book Page 8 Tuesday, March 20, 2018 5:27 PM

Sidan laddas ...

Motorola TALKABOUT T92 H2O Bruksanvisning

Motorola TALKABOUT T92 H2O Bruksanvisning

på andra språk

Relaterade papper

Andra dokument