Dometic CAM200 Bruksanvisningar

CAM200

Rear View Video Camera

Installation and Operating Manual . . . . . 13

Rückfahrvideokamera

Montage- und Bedienungsanleitung . . . 21

Caméra vidéo de recul

Instructions de montage

et de service . . . . . . . . . . . . . . . . . . . . . . . 29

Cámara de vídeo de marcha atrás

Instrucciones de montaje y de uso . . . . . 37

Câmara de marcha-atrás

Instruções de montagem e manual de

instruções . . . . . . . . . . . . . . . . . . . . . . . . . 45

Videocamera per la retromarcia

Istruzioni di montaggio e d’uso . . . . . . . . 53

Achteruitrijvideocamera

Montagehandleiding en

gebruiksaanwijzing. . . . . . . . . . . . . . . . . . 61

Bakvideokamera

Monterings- og betjeningsvejledning. . . 69

Backningsvideokamera

Monterings- och bruksanvisning. . . . . . . 77

Ryggevideokamera

Monterings- og bruksanvisning . . . . . . . 85

Peruutusvideokamera

Asennus- ja käyttöohje. . . . . . . . . . . . . . . 93

Видеокамера заднего вида

Инструкция по монтажу

и эксплуатации. . . . . . . . . . . . . . . . . . . . .101

Kamera cofania

Instrukcja montażu i obsługi . . . . . . . . . 109

Cúvacia kamera

Návod na montáž a uvedenie

do prevádzky . . . . . . . . . . . . . . . . . . . . . .117

Couvací kamera

Návod k montáži a obsluze . . . . . . . . . . 125

Tol a tók a m e ra

Szerelési és használati útmutató . . . . . . 133

EN

DE

FR

ES

PT

IT

NL

DA

SV

NO

FI

RU

PL

SK

CS

HU

POWER & CONTROL

CAMERAS

DometicCAM200_IOM_4445103020_EMEA16_2021-03-23.book Page 1 Tuesday, March 23, 2021 4:53 PM

by copyright and design law. The underlying technical design and the products contained

herein may be protected by design, patent or be patent pending. The trademarks

mentioned in this manual belong to Dometic Sweden AB. All rights are reserved.

DometicCAM200_IOM_4445103020_EMEA16_2021-03-23.book Page 2 Tuesday, March 23, 2021 4:53 PM

CAM200

3

1 2 3

4

9

6

8

5

7

10 11

12

1

DometicCAM200_IOM_4445103020_EMEA16_2021-03-23.book Page 3 Tuesday, March 23, 2021 4:53 PM

CAM200

4

2

3

4

5

DometicCAM200_IOM_4445103020_EMEA16_2021-03-23.book Page 4 Tuesday, March 23, 2021 4:53 PM

CAM200

5

6

7

1

3

4

2

8

DometicCAM200_IOM_4445103020_EMEA16_2021-03-23.book Page 5 Tuesday, March 23, 2021 4:53 PM

CAM200

6

9

DometicCAM200_IOM_4445103020_EMEA16_2021-03-23.book Page 6 Tuesday, March 23, 2021 4:53 PM

CAM200

7

0

DometicCAM200_IOM_4445103020_EMEA16_2021-03-23.book Page 7 Tuesday, March 23, 2021 4:53 PM

CAM200

8

6-8 mm

1.

2.

a

DometicCAM200_IOM_4445103020_EMEA16_2021-03-23.book Page 8 Tuesday, March 23, 2021 4:53 PM

CAM200

9

1.

2. 3.

Ø 30

4.

b

DometicCAM200_IOM_4445103020_EMEA16_2021-03-23.book Page 9 Tuesday, March 23, 2021 4:53 PM

CAM200

10

1.

2.

3.

5.

4.

c

DometicCAM200_IOM_4445103020_EMEA16_2021-03-23.book Page 10 Tuesday, March 23, 2021 4:53 PM

CAM200

11

1.

2.

d

2.

1.

e

f

DometicCAM200_IOM_4445103020_EMEA16_2021-03-23.book Page 11 Tuesday, March 23, 2021 4:53 PM

CAM200

12

2.

3.

4.

1.

g

DometicCAM200_IOM_4445103020_EMEA16_2021-03-23.book Page 12 Tuesday, March 23, 2021 4:53 PM

CAM200

EN

13

Please read these instructions carefully and follow all instructions, guidelines, and warnings included in this product

manual in order to ensure that you install, use, and maintain the product properly at all times. These instructions

MUST stay with this product.

By using the product, you hereby confirm that you have read all instructions, guidelines, and warnings carefully and

that you understand and agree to abide by the terms and conditions as set forth herein. You agree to use this prod-

uct only for the intended purpose and application and in accordance with the instructions, guidelines, and warn-

ings as set forth in this product manual as well as in accordance with all applicable laws and regulations. A failure to

read and follow the instructions and warnings set forth herein may result in an injury to yourself and others, damage

to your product or damage to other property in the vicinity. This product manual, including the instructions, guide-

lines, and warnings, and related documentation, may be subject to changes and updates. For up-to-date product

information, please visit dometic.com.

Contents

1 Explanation of symbols. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

2 Safety and installation instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

3 Scope of delivery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

4 Intended use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

5 Technical description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

6 Information on the electrical connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

7 Mounting the camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

8 Cleaning and caring for the camera. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

9 Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

10 Disposal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

11 Technical data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

1 Explanation of symbols

!

A

WARNING!

Safety instruction: Indicates a hazardous situation that, if not avoided, could result in

death or serious injury.

CAUTION!

Safety instruction: Indicates a hazardous situation that, if not avoided, could result in

minor or moderate injury.

NOTICE!

Indicates a situation that, if not avoided, can result in property damage.

DometicCAM200_IOM_4445103020_EMEA16_2021-03-23.book Page 13 Tuesday, March 23, 2021 4:53 PM

Safety and installation instructions CAM200

EN

14

I

2 Safety and installation instructions

The manufacturer accepts no liability for damage in the following cases:

• Faulty assembly or connection

• Damage to the product resulting from mechanical influences and incorrect connection voltage

• Alterations to the product without express permission from the manufacturer

•Use for purposes other than those described in the operating manual

Please observe the prescribed safety instructions and stipulations from the vehicle

manufacturer and service workshops.

!

WARNING!

Inadequate supply cable connections could result in short circuits, which could have as

a consequence that:

• Cable fires occur

• The airbag is triggered

• Electronic control devices are damaged

• Electric functions fail (indicators, brake light, horn, ignition, lights)

A

NOTICE!

To prevent the risk of short circuits, always disconnect the negative terminal of the

vehicle's electrical system before working on it.

If the vehicle has an additional battery, its negative terminal should also be discon-

nected.

Please observe the following instructions:

• When working on the following cables, only use insulated cable lugs, plugs and flat push-on

receptacles:

– 30 (direct supply from positive battery terminal)

– 15 (connected positive terminal, behind the battery)

– 31 (return line from the battery, earth)

– L (indicator lights left)

– R (indicator lights right)

Do not use terminal strips.

• Use a crimping tool to connect the cables.

• When connecting to cable 31 (earth), screw the cable

– to the vehicle's earth bolt with a cable lug and a gear disc or

– to the sheet-metal bodywork with a cable lug and a self-tapping screw.

Ensure that there is a good earth connection.

NOTE

Supplementary information for operating the product.

DometicCAM200_IOM_4445103020_EMEA16_2021-03-23.book Page 14 Tuesday, March 23, 2021 4:53 PM

CAM200

EN

15

If you disconnect the negative terminal of the battery, all data stored in the volatile memories will

be lost.

• The following data must be set again, depending on the vehicle equipment options:

–Radio code

–Vehicle clock

–Timer

– On-board computer

–Seat position

You can find instructions for making these settings in the appropriate operating instructions.

Observe the following installation instructions:

!

CAUTION!

• Secure the parts installed in the vehicle in such a way that they cannot become loose

under any circumstances (sudden braking, accidents) and cause injuries to the

occupants of the vehicle.

• Secure any parts of the system covered by the bodywork in such a manner that they

cannot be come loose or damage other parts and cables or impair vehicle functions

(steering, pedals, etc).

• Always follow the safety instructions of the vehicle manufacturer.

Some work (e.g. on retention systems such as the AIRBAG etc.) may only be

performed by qualified specialists.

A

NOTICE!

• To prevent damage when drilling, make sure there is sufficient space on the other

side for the drill head to come out.

• Deburr all drill holes and treat them with a rust-protection agent.

Observe the following instructions when working with electrical parts:

A

NOTICE!

• When testing the voltage in electrical cables, only use a diode test lamp or a

voltmeter.

Test lamps with an illuminant take up voltages which are too high and which can

damage the vehicle's electronic system.

• When making electrical connections, ensure that:

– they are not kinked or twisted

– they do not rub on edges

– they are not laid in sharp edged ducts without protection.

• Insulate all connections.

• Secure the cables against mechanical wear with cable binders or insulating tape,

for example to existing cables.

DometicCAM200_IOM_4445103020_EMEA16_2021-03-23.book Page 15 Tuesday, March 23, 2021 4:53 PM

Scope of delivery CAM200

EN

16

The camera is watertight. However, the sealings on the camera cannot withstand a high-pres-

sure cleaner (fig. 4, page 4).

Observe also the following instructions:

• Do not open the camera, as this impairs the sealing and the function of the camera (fig. 5,

page 4).

• Do not pull at the cables, as this impairs the sealing and the function of the camera (fig. 6,

page 5).

• The camera is not suitable for submerged operation (fig. 7, page 5).

3Scope of delivery

4Intended use

The camera CAM200 is a rear view video camera for use on bike racks.

The camera can be used to observe the space around the vehicle from the driver's seat when

manoeuvring or parking, for example.

!

This product is only suitable for the intended purpose and application in accordance with these

instructions.

This manual provides information that is necessary for proper installation and/or operation of the

product. Poor installation and/or improper operating or maintenance will result in unsatisfactory

performance and a possible failure.

The manufacturer accepts no liability for any injury or damage to the product resulting from:

• Incorrect assembly or connection, including excess voltage

No. in

fig. 8,

page 5

Quantity Description Ref. no.

1 1 Camera CAM200 9600049683

2 1 Connector grommet CAB25 9600027073

3 2 Cable clip

4 1 Spiral cable 9600026478

– 1 Installation and Operating Manual

WARNING!

Risk of injury!

Since rear view systems are designed merely as an additional aid for reversing, it does

not relieve you of the duty to take proper care when reversing.

DometicCAM200_IOM_4445103020_EMEA16_2021-03-23.book Page 16 Tuesday, March 23, 2021 4:53 PM

CAM200

EN

17

• Incorrect maintenance or use of spare parts other than original spare parts provided by the man-

ufacturer

• Alterations to the product without express permission from the manufacturer

• Use for purposes other than those described in this manual

Dometic reserves the right to change product appearance and product specifications.

5 Technical description

The camera, which is encased in plastic housing, transmits the image to a monitor via a cable.

The camera is mounted under the profile of the bike rack and provides a free view with a loaded

bike rack.

Two automatically operating camera modules provide the image with the bike rack folded up or

down (fig. 9, page 6).

Three distance lines (green, yellow, and red) are displayed (fig. 0, page 7).

6 Information on the electrical connections

6.1 Laying cables

A

Please observe the following instructions:

• As far as possible, use original openings or alternative openings for the connecting cable duct,

e.g. the paneling edges, ventilation grilles or blank panels. If no openings are available, you

must drill holes for the cables. Check beforehand that there is sufficient room for the drill head

to come out on the other side.

• Wherever possible lay cables inside the vehicle, as they are better protected inside than outside

the vehicle.

If you do need to lay a cable outside the vehicle, ensure that it is well secured (use additional

cable ties, insulating tape, etc.).

• To prevent damage to the cables, when laying them ensure that there is sufficient distance to

hot or moving vehicle components (exhaust pipes, drive shafts, light systems, fans, heater etc.).

Use corrugated piping or other protective materials to protect against mechanical wear.

• Screw on the plug connection of the connecting cables to protect against water penetration

(fig. d, page 11).

NOTICE! Risk of damage!

• To prevent damage, when drilling ensure that there is sufficient space on the other

side for the drill head to come out.

• Cables and connections which are not properly installed will cause malfunctions or

damage to components. Correct installation of cables and connections is the basic

prerequisite for lasting and trouble-free operation of the retrofitted components.

• The cables may not be exposed for long periods to solvents such as benzine, as the

solvents can damage the cable.

DometicCAM200_IOM_4445103020_EMEA16_2021-03-23.book Page 17 Tuesday, March 23, 2021 4:53 PM

Mounting the camera CAM200

EN

18

• When laying electric connections, ensure that

– They are not kinked or twisted

– They do not rub on edges

– They are not laid in sharp edged ducts without protection (fig. 3, page 4)

• Attach the cables securely in the vehicles to prevent tripping hazards. Use cable binders, insu-

lating tape or glue the cables in place.

• Protect every through-hole made in the bodywork against water penetration, e.g. by using a

cable with a sealant and by spraying the cable and the cable sleeve with sealant.

I

7 Mounting the camera

7.1 Tools required

For installation and assembly you will require the following tools:

• Drill bit set (fig. 1 1, page 3)

• Drill (fig. 1 2, page 3)

• Screwdriver (fig. 1 3, page 3)

• Set of ring or open-ended spanners (fig. 1 4, page 3)

• Measuring ruler (fig. 1 5, page 3)

• Hammer (fig. 1 6, page 3)

• Centre punch (fig. 1 7, page 3)

To make and test the electrical connection, the following tools are required:

• Diode test lamp (fig. 1 8, page 3) or voltmeter (fig. 1 9, page 3)

• Crimping tool (fig. 1 10, page 3)

• Insulating tape (fig. 1 11, page 3)

• Cable bushing sleeves, if necessary

To fasten the cables you may require additional cable binders.

7.2 Mounting and connecting the camera

Proceed as shown (fig. a, page 8 to fig. f, page 11).

A

NOTE

Do not start sealing the through-holes until all installation work has been finished for the

camera, and the required cable lengths have been established.

NOTICE! Risk of damage!

Ensure that there is sufficient space on the other side for the drill head to come out

DometicCAM200_IOM_4445103020_EMEA16_2021-03-23.book Page 18 Tuesday, March 23, 2021 4:53 PM

CAM200

EN

19

I

Aligning the camera

➤ Use the monitor image to align the camera (fig. g, page 12).

➤ Use the monitor image to check the function of the camera.

8 Cleaning and caring for the camera

A

➤ Clean the camera with a soft, damp cloth from time to time.

9Warranty

The statutory warranty period applies. If the product is defective, please contact your retailer or the

manufacturer's branch in your country (see dometic.com/dealer).

For repair and warranty processing, please include the following documents when you send in the

product:

• A copy of the receipt with purchasing date

• A reason for the claim or description of the fault

10 Disposal

➤ Place the packaging material in the appropriate recycling waste bins, wherever possible.

M

If you wish to finally dispose of the product, ask your local recycling center or specialist

dealer for details about how to do this in accordance with the applicable disposal

regulations.

NOTE

To minimise corrosion in the plug, apply a small amount of grease – such as pin grease

– inside the plug.

NOTICE! Risk of damage!

Do not use sharp or hard objects to clean the device as these may damage the device.

DometicCAM200_IOM_4445103020_EMEA16_2021-03-23.book Page 19 Tuesday, March 23, 2021 4:53 PM

Technical data CAM200

EN

20

11 Technical data

Approval

The device has the E24 approval.

PerfectView CAM200

Ref. no: 9600049683

Image sensor: 1/4" CMOS

Pixels: approx. 307000 pixels

Video standard: NTSC

Light sensitivity: 0,1 Lux

Operating voltage: 10 – 16 Vg

Power consumption: 1 W

Protection class: IP69

Operating temperature: –30 °C to 70 °C

Dimensions W x H x D: 165 x 35 x 42 mm

Weight: 250 g

24

DometicCAM200_IOM_4445103020_EMEA16_2021-03-23.book Page 20 Tuesday, March 23, 2021 4:53 PM

Sidan laddas ...

Dometic CAM200 Bruksanvisningar

Dometic CAM200 Bruksanvisningar

på andra språk

Relaterade papper

Andra dokument