Sony KL-37W1 Bruksanvisning

varumärke: Sony

Modell: KL-37W1

Typ: Bruksanvisning

Denna manual är också lämplig för

KL-50W1

LCD Projection TV

Operating Instructions

Getting Started

Basfunktioner

Komma igång S

Instrukcja Obsàugi

Hasznèlati Øtmutatô

Procedimientos

iniciales

Instrucciones de

funcionamiento

Como começar

Instruções de

funcionamento

Przed uéciem po raz

pierwszy

A kíszÖlík

Özembehelyezíse

àÌcÚpyÍáËÓ Ôo

íÍcÔÎyaÚaáËË

èoÀÖoÚoÇÍa Í

íÍcÔÎyaÚaáËË

3-858-007-11 (1)

KL-37W1

KL-50W1

Important Information

Please read the following information on using and

maintaining the TV, for optimum viewing quality.

Picture Quality

• Avoid touching the screen, and take care not to scratch

the surface with hard objects.

Illumination

To obtain a clear picture, do not expose the screen to

direct illumination or direct sunlight. If possible, use spot

lighting directed down from the ceiling.

Installation

• To prevent over heating of the set, do not block the

ventilation openings.

• Do not install the TV in a hot or humid place, or in a place

subject to direct sunlight, excessive dust or mechanical

vibration.

• After transporting the TV directly from a cold to a warm

location, or if the room temperature has changed

suddenly, pictures may be blurred or show poor colour

over portions of the picture. This is because moisture has

condensed on the mirrors or lenses inside the TV. Let the

moisture evaporate before using the TV.

Maintenance

• Save the original shipping carton and packing material to

use if you ever have to ship your TV. For maximum

protection, repack your TV as it was originally packed at

the factory.

• To keep the cabinet looking brand-new, periodically clean

it with a soft cloth. Stubborn stains may be removed with a

cloth slightly dampened with a mild detergent solution.

Never use strong solvents such as thinner or benzene, or

abrasive cleaners since these will damage the cabinet. As

a safety precaution, unplug the TV before cleaning it.

• To remove dust from the front of the screen, unplug the

TV and wipe gently with a soft cloth lightly dampened with

water or a mild detergent solution, using vertical strokes

only. Then wipe it with a dry, soft cloth. Never use

solvents or thinners for cleaning purposes.

• If the picture turns dark after the TV has been in use for a

long period of time, it may be necessary to clean the

inside of the TV. Consult qualified service personnel for

this.

WARNING

To prevent fire or shock hazard, do not expose the unit to

rain or moisture.

Dangerously high voltages are present inside the set. Do

not open the cabinet. Refer servicing to qualified

personnel only.

Safety Information

All TVs operate on extremely high voltages. To prevent

fire or electric shock, please follow the safety procedures

below. For your protection, refer all servicing to qualified

personnel only.

For general safety:

• Do not expose the TV to rain or moisture.

• Do not open the rear cover.

For safe operations:

• Do not operate the TV on any other voltages, but 220–

240 V AC.

• Do not operate the TV if any liquid or solid object falls in it

- have it checked immediately.

• Do not keep the set plugged in if you are not going to use

it for several days.

• Do not pull on the power cord to disconnect the TV. Pull it

out by the plug.

• Do not place anything on the surface of the front panel

cover when you open it.

Contents

Overview ................................................................................... 4

Getting Started...............................................................

Step 1 Preparation ..................................................................... 6

Check the supplied accessories ...................................... 6

Insert the battery into the Remote Commander................ 6

Connect the aerial ........................................................... 6

Step 2 Tuning in to TV Stations .................................................. 7

Choose a language ......................................................... 7

Display the menu ............................................................ 7

Preset Channels automatically ........................................ 8

Preset Channels manually .............................................. 9

Additional Presetting Functions ................................................ 10

Sorting Programme Positions........................................ 10

Using “Further Programme Preset” ............................... 11

Skipping Programme Positions ..................................... 12

Captioning a Station Name ........................................... 12

Parental Lock................................................................ 13

Tuning in a Channel Temporarily ................................... 13

Operating Instructions.................................................

Watching the TV....................................................................... 14

Switching the TV on and off ........................................... 14

Selecting TV Programmes ............................................ 14

Adjusting the Volume .................................................... 14

Operating the TV Using the Buttons on the TV ............... 14

Watching Teletext or Video Input ................................... 15

More Convenient Functions .......................................... 15

Adjusting and Setting the TV Using the Menu ........................... 16

Adjusting the Picture and Sound ................................... 16

Graphic Equalizer ......................................................... 17

Using the Sleep Timer................................................... 17

PAP (Picture and Picture)......................................................... 18

Operating Screen Mode/PAP Using the Menu ............... 19

Auto Format.................................................................. 19

Teletext.................................................................................... 20

Direct Access Functions................................................ 20

Using the Teletext Menu ............................................... 21

User Page Bank System ............................................... 22

Connecting and Operating Optional Equipment ........................ 23

Connecting Optional Equipment.................................... 23

Selecting lnput and Output ............................................ 24

Using AV Preset ........................................................... 25

Remote Control of Other Sony Equipment ..................... 26

For Your Information ................................................................ 27

Optimum Viewing Area ................................................. 27

Cleaning of the Air Filter ................................................ 28

Replacing the Lamp ...................................................... 29

Troubleshooting ............................................................ 30

Specifications ............................................................... 30

Warning Indicators ........................................................ 31

Stabilizing the Projection TV .......................................... 31

Getting Started

Operating Instructions

Name

Main power switch

Standby indicator

Stereo A/B indicators

Programme

Volume buttons

Input select buttons

Headphones jack

Input jacks (S video/video/audio)

Symbol

A-µ-B

PROGR+/–

+/–

3, 3, 3

Overview

This section briefly describes the buttons and controls on the TV

set and on the Remote Commander. For more information, refer to

the pages given next to each description.

TV set-front

Refer to page

PROGR

Name

PAP on/off button

PAP source selector

Swap button

PAP freeze button

Name

Menu on/off button

Select buttons

OK(confirming)button

Back button

Remote commander

TV/Teletext

operation

Full-Function sideSimple side

Note

The SAT button does not

operate with this TV.

PAP (Picture-and-picture) operation

Menu operation

Refer to page

Symbol

VTR1/2/3,

MDP

;; − :: Λ

ϑ α φ

PROGR +/–

Name

Video equipment selector

Video equipment operation

buttons

Refer to page

Video operation

PAP operation

Menu operation

Video operation

Name

Mute on/off button

Standby button

TV power on/TV mode selector

button

Teletext button

Input mode selector

Output mode selector

Number buttons

Double-digit entering button

Direct channel entering button

Volume control button

Programme selectors

Teletext page access buttons

Picture adjustment button

Sound adjustment button

On-screen display button

Teletext hold button

Time display button

Fastext buttons

“Freeze” button

Button to change Screen Format

Refer to page

∃

Symbol

1,2,3,4,5,6,

7,8,9 and 0

–/--

+/–

PROGR +/–

[

ΛΛΛΛ

TV/Teletext operation

Refer to page

Symbol

>+/ ?–

≅

PROGR

RM-838

PROGR

VTR 1-2-3

MDP

SAT

RM-838

USE

MEM

RESET

R/D/D/D

L/G/S/I

R/D/D/D

L/G/S/I

R/D/D/D

L/G/S/I

R/D/D/D

L/G/S/I

Check the supplied accessories

When you’ve taken everything

out of the carton, check that you

have these items:

• RM-838 Remote Commander

• One IEC designation R6 battery

• Lamp (1)

• Wrench (1)

• Bracket (2)

Insert the battery into the Remote Commander

Step 1 Preparation

Getting Started

Fit an IEC aerial connector attached to 75-ohm coaxial cable (not

supplied) to the ) socket at the rear of the TV.

RM-838

PROGR

VTR 1-2-3

MDP

SAT

PROGR

RM-838

PROGR

RM-838

Remove the cover. Check the correct

polarities.

Refit the outside cover

making sure that the Full-

Function side is visible to use

the menu in step 2.

Note: Always remember

to dispose of used

batteries in an

enviromental friendly

way.

Connect the aerial

PROGR

RM-838

LANGUAGE

English

Deutsch

Français

Italiano

Español

Nederlands

Português

Suomi

Svenska

¶ Ł ØºÆ

Türkçe

and press OK

Sec

Select

PROGR

VTR 1-2-3

MDP

SAT

RM-838

USE

MEM

RESET

Step 2 Tuning in to TV Stations

Once you have set up the TV, you can choose the language of the

menu. Then, you should preset the channels (up to 100 channels)

by choosing either the automatic or manual method. The

automatic method is easier if you want to preset all receivable

channels at once. Use the manual method if you only have a few

channels and want to preset channels one by one.

Before you begin

• Check that the Full-Function side of the Remote Commander is

visible.

• Locate Menu operation buttons on the Remote Commander.

They are shaded in the illustration at the left.

Choose a language

1 Press φ on the TV.

The TV will switch on. If the standby indicator on the TV is lit, press

Ο or a number button on the Remote Commander.

2 Press the MENU button.

The LANGUAGE menu appears. (See Fig. 1.)

3 Select the language you want with > + or ? – and press OK.

Display the menu

Press MENU.

The main menu appears. (See Fig. 2.)

Using > + or ? – select the symbol

and press OK.

Now, choose one of the methods described overleaf:

“Preset Channels Automatically”

“Preset Channels Manually”

To go back to main

Keep pressing ≅.

To go back to the

normal TV picture

Press MENU. Normal

TV picture will be

restored after one

minute if menu functions

are not selected.

Note on the Demo

function

If you choose Demo in

the Installation menu,

you can see a sequential

demonstration of the

menu functions.

Press MENU to stop the

function.

φ Fig. 2

Fig. 1

Auto Format

Select and press OK

Clip Board

PAP

Strobe

Screen Position

Screen Mode

[off]

[on]

[ ]

[ ]zoom

SCREEN MODE

Preset channels automatically

1 Select the symbol for “Preset” with >+ or ?– and press OK.

The PRESET menu appears. (See Fig. 3.)

2 Select “Auto Programme” with >+ or ?– and press OK.

The AUTO PROGRAMME menu appears. (See Fig. 4.)

3 Press OK.

Select if necessary the TV broadcast system (B/G for Western

European or D/K for Eastern European countries) with >+ or ?–

and press OK. The first element of the “PROG” number will be

highlighted.

4 Select the programme (number button) from which you want to

start presetting. Select the first element of the double-digit number

with >+ or ?– or the number buttons (e.g., For “04,” select “0”

here) and press OK.

The second element of “PROG” will be highlighted.

5 Select the second element of the double-digit number with >+ or

?– or the number buttons (e.g., For “04,” select “4” here) (See Fig.

5) and press OK.

6 Select “C” or “S” with >+ or ?– and press OK.

The automatic channel presetting starts.

When presetting is finished, the preset menu reappears. All

available channels are now stored on successive number buttons.

Press menu to restore normal TV picture.

To go back to the main

Keep pressing ≅.

To stop automatic

channel presetting

Press ≅ on the Remote

Commander.

Notes

• After presetting the

channels automatically,

you can check which

channels are stored on

which programme

positions.

For details, see

“Displaying the

Programme Table” on

page 15.

• You can sort the

programme positions to

have them appear on

screen in the order you

like. For details, see

“Sorting Programme

Positions” on page 10.

Fig. 3

Fig. 4

Fig. 5

Installation

Select and press OK

Programme Sorting

Manual Programme Preset

Auto Programme

PRESET

Parental Lock

B/G

Select and press OK

AUTO PROGRAMME

SYS PROG

C25

–

LABEL

––––01

B/G

SYS PROG

C25

–

LABEL

––––04

MANUAL PROGRAMME PRESET

PROG

Select and press OK

B/G

SYS

C21

C34

C33

C45

C02

C08

C10

C12

C20

C59

off

SEARCH LABEL

-----

Preset channels manually

1 Select the symbol for “Preset” with >+ or ?– and press OK.

The PRESET menu appears. (See Fig. 6.)

2 Select “Manual Programme Preset” with >+ or ?– and press OK.

The MANUAL PROGRAMME PRESET menu appears. (See Fig.

7.)

3 Using >+ or ?–, select the programme position (number button) to

which you want to preset a channel, and press OK.

4 Select, if necessary the TV broadcast system or a video input

source (EXT)) with >+ or ?–.

5 Then press OK. The CH position will be highlighted. (See Fig. 8.)

6 Using >+ or ?–, select C (to preset a regular channel), S (cable

channel) or F (to tune in by frequency) and press OK.

The first element of the “CH” number will be highlighted.

If you have selected EXT in step 5, select the video input source

with >+ or ?–. (See Fig. 9.)

There are two ways to preset channels, If you know the channel

number, go to step “7-Manual,”

If you don’t know the channel number, go to step “7-Search.”

7 Manual

-a Select the first element of the “CH” number with >+ or ?– or the

number buttons and press OK.

The second element of the “CH” number will be highlighted.

-b Select the second element of the number with >+ or ?– or the

number buttons.

The selected number appears. (See Fig. 10.)

-c Press OK

The “SEARCH” position is highlighted and the selected channel is

now stored. (See Fig. 11.)

-d Press OK until the cursor appears by the next programme position.

-e Repeat steps 3 to 7 to preset other channels.

7 Search

-a Press OK repeatedly until the colour of the SEARCH position

changes.

-b Start searching for the channel with >+ (up) or ?– (down).

The CH position changes colour. (See Fig. 12.)

The CH number starts counting up or downwards. When a

channel is found, it stops. (See Fig. 13.)

-c Press OK if you want to store this channel. If not, press >+ or ?–

to continue channel searching.

-d Press OK until the cursor appears by the next programme position.

-e Repeat steps 3 to 7 to preset other channels.

Use this method if there

are only a few channels

in your area to preset or if

you want to preset

channels one by one.

You may also allocate

programme numbers to

various video input

sources.

If you have made a

mistake

Press ≅ to go back to

the previous position.

To return to the main

Keep pressing ≅.

To go back to the

normal TV picture

Press MENU.

To tune in a channel by

frequency

After selecting F in step 6,

enter three digits using

the number buttons.

Installation

Select and press OK

Programme Sorting

Manual Programme Preset

Auto Programme

PRESET

Parental Lock

Fig. 6

Fig. 7

Fig. 8

Fig. 9

Fig. 10

Fig. 11

Fig. 12

Fig. 13

2 C –––––21B/G off

3 AV1 –––––EXT

2 C –––––35B/G off

2 C –––––50B/G

PROGRAMME SORTING

PROG

Select and press OK

C15

C03

C04

C07

C09

C12

C13

C14

CH LABEL

BBC 1

BBC 2

ITV

MBC

-----

Move PR 1 to PR - -

PROGRAMME SORTING

PROG

Select and press OK

C03

C04

C07

C09

C12

C13

C14

C15

CH LABEL

BBC 2

ITV

MBC

-----

BBC 1

Move PR 8 to PR - -

Additional Presetting Functions

This section shows you additional presetting functions such as

sorting or skipping programme positions, captioning a station

name, manual fine-tuning, and using the parental lock.

Before you begin

• Check that the Full Function side of the Remote

Commander is visible.

• Locate the Menu operation buttons.

Sorting Programme Positions

With this function, you can sort the programme positions to a

preferable order.

1 Press MENU to display the main menu.

2 Select the symbol

for “Preset” with >+ or ?– and press OK.

The PRESET menu appears.

3 Select “Programme Sorting” with >+ or ?– and press OK.

The PROGRAMME SORTING menu appears. (See Fig. 14.)

4 Using >+ or ?–, select the programme position you want to move

to another and press OK.

The colour of the selected position changes. (See Fig. 15.)

5 Using >+ or ?–, select the programme position to which you want

to move the channel of the programme position selected in step 4

and press OK. Now the programme positions have been sorted.

(See Fig. 16.)

6 Repeat steps 4 and 5 to sort other programme positions.

For higher programme

positions

The display scrolls

automatically.

If you have made a

mistake

Press ≅ to go back to

the previous position

To go back to main

Keep pressing ≅.

To go back to the

normal TV picture

Press MENU.

PROGRAMME

SORTING

PROGR

VTR 1-2-3

MDP

SAT

RM-838

USE

MEM

RESET

Fig. 14

Fig. 15

Fig. 16

8 BBC1C15

FURTHER PROGRAMME PRESET

PROG

Select and press OK

ATT

- 1

VOL

IN-AMP AFT

- 1

off

Using “Further Programme

Preset”

Using the menu “further Programme Preset” you can

a) in case of a strong local aerial signal (striped picture) attenuate the

signal individually for each programme position (RF attenuator).

b) individually adjust and store the volume level of each channel

(Volume offset).

c) in case of a strong sound signal (distorted sound), attenuate the

sound signal for each programme position.

d) use the manual fine tuning to obtain a better picture reception, if

the picture is distorted. Normally the AFT (automatic fine tuning) is

operating.

1 Press MENU to display the main menu.

2 Select the symbol

for “Preset” with >+ or ?– and press OK.

The PRESET menu appears.

3 Select “Installation” with >+ or ?– and press OK. The

INSTALLATION menu appears.

4 Select “Further Programme Preset” with >+ or ?– and press OK.

The FURTHER PROGRAMME PRESET menu appears (See Fig.

17).

5 Using >+ or ?– select the desired programme position and press

OK once to select a) “ATT” (RF Attenuator), twice to select b)

“VOL” (Volume offset), three times to select c) “IN-AMP” (Input

Amplifier) or four times to select d) AFT (Automatic Fine Tuning).

The selected item changes colour.

To adjust or change:

a) RF attenuator (ATT)

Using >+ or ?– select “On” for the selected programme position.

Press OK to confirm the selection. Repeat step 5 to attenuate

other programme positions.

b) Volume offset (VOL)

Using >+ or ?– you can adjust the volume level for the selected

programme position within a range form –7 to +7.

Press OK to store the volume level.

Repeat step 5 to set the volume level for other programme

positions.

c) IN-AMP (input amplifier)

Using >+ or ?– select “Off” for the selected programme position.

Press OK to confirm the selection. Repeat step 5 to switch off the

input amplifier for other programme positions.

d) AFT

Using >+ or ?– you can fine-tune the channel within a range from

–15 to +15. Press OK to store the fine-tuned level. Repeat step 5

to fine-tune the other channels.

6 Press MENU to return to the normal TV mode.

INSTALLATION

To reactivate AFT

(Automatic Fine

Tuning)

Repeat from the

beginnig and select “ON”

in step 5.

Fig. 17

MANUAL PROGRAMME PRESET

PROG

Select and press OK

B/G

SYS

C21

C24

C25

C27

C28

C22

C26

C25

C23

C29

off

SEARCH LABEL

-----

MANUAL PROGRAMME PRESET

PROG

Select and press OK

B/G

SYS

C21

C24

C25

C27

C28

C22

C26

C25

C23

C29

off

SEARCH LABEL

-----

MANUAL

PROGRAMME

PRESET

If you have made a

mistake

Press ≅ to go back to

the previous position.

To go back to main

Keep pressing ≅.

To go back to the

normal TV picture

Press MENU.

Skipping Programme Positions

You can skip unused programme positions when selecting

programmes with PROGR +/– buttons. However, the skipped

programmes may still be called up when you use the number

buttons.

1 Press MENU to display the main menu.

2 Select the symbol

for “Preset” with >+ or ?– and press OK.

The PRESET menu appears.

3 Select “Manual Programme Preset” with >+ or ?– and press OK.

The MANUAL PROGRAMME PRESET menu appears. (See Fig.

18.)

4 Using >+ or ?–, select the programme position which you want to

skip and press OK.

The “SYS” position changes colour.

5 Press >+ or ?– until “– – –” appears in the SYSTEM position.

(See Fig. 19.)

6 Press OK. (See Fig. 20.)

When you select programmes using the PROGR +/– buttons, the

programme position will be skipped.

7 Repeat steps 4 to 6 to skip other programme positions.

Captioning a Station Name

Programme names are usually automatically taken from Teletext if

available, You can also “name” a channel or an input video source

using up to five characters (letters or numbers) to be displayed on

the TV screen (e.g. BBC1). Using this function, you can easily

identify which channel or video source you are watching.

1 Press MENU to display the main menu.

2 Select the symbol

for “Preset” with >+ or ?– and press OK.

The PRESET menu appears.

3 Select “Manual Programme Preset” with >+ or ?– and press OK.

The MANUAL PROGRAMME PRESET menu appears. (See Fig.

21.)

4 Using >+ or ?–, select the programme position you want to

caption and press OK repeatedly until the first element of the

LABEL position is highlighted.

5 Select a letter or number with >+ or ?– and press OK.

The next element will be highlighted.

Select other characters in the same way. If you want to leave an

element blank, select - and press OK. (See Fig. 22.)

6 After selecting all the characters, press OK repeatedly until the

cursor appears by the next programme position (at the left margin).

Now the caption you chose is stored. (See Fig. 23.)

7 Repeat steps 5 and 6 to caption names for other channels.

MANUAL

PROGRAMME

PRESET

Fig. 18

Fig. 19

Fig. 20

Fig. 21

Fig. 22

Fig. 23

PROGR

3 –––

4 B/G

3 –––

2 C S––––25B/G off

2CSONY25B/G off

C - -

3 C26 C 4

2 C42 BBC 1

PROG CH LABEL

1 C25 BBC 2

0 AV1 VHS

PARENTAL LOCK

If you try to select a

programme that has

been blocked

The message

“LOCKED” appears on

the blank TV screen.

Parental Lock

You can prevent undesirable broadcasts from appearing on the

screen. We suggest you use this function to prevent children from

watching programmes which you consider unsuitable.

1 Press MENU to display the main menu.

2 Select the symbol

for “Preset” with >+ or ?– and press OK.

The PRESET menu appears.

3 Select “Parental Lock” with >+ or ?– and press OK.

The PARENTAL LOCK menu appears. (See Fig. 24.)

4 Using >+ or ?–, select the programme position you want to block

and press OK.

The symbol

appears in front of the programme number

indicating that this programme is now blocked. (See Fig. 25.)

5 Repeat step 4 to block other programme positions.

Cancelling blocking

1 On the PARENTAL LOCK menu, select the programme position

you want to unblock with >+ or ?–.

2 Press OK.

The symbol

disappears indicating that the blocking has been

cancelled.

Tuning in a Channel Temporarily

You can tune in to a channel temporarily, even when it has not

been preset. Use the buttons on the Full-Function side of the

Remote Commander.

1 Press C on the Remote Commander. For cable channels, press C

twice.

The indication “C” ( “S” for cable channels) appears on the screen.

(See Fig. 26.)

2 Enter the double-digit channel number using the number buttons

(e.g. for channel 4, first press 0, then 4).

The channel appears.

However, the channel will not be stored.

Fig. 24

Fig. 25

PARENTAL LOCK

PROG

Select and press OK

AV1

C25

C42

C26

C34

C35

C36

C37

CH LABEL

VHS

BBC 2

BBC 1

C 4

ITV

-----

Fig. 26

PROGR

RM-838

Operating Instructions

Watching the TV

If no picture appears

when you depress φ

on the TV and if the

standby indicator on

the TV is lit, the TV is in

standby mode.

Press Ο or one of the

number buttons to

switch it on.

This section explains the basic functions you use while watching

TV. Most of the operations can be done using the simple side of

the Remote Commander.

Switching the TV on and off

Switching on

Depress φ on the TV.

Switching off temporarily

Press φ on the Remote Commander.

The TV enters standby mode and the standby indicator on the front

of the TV lights up in red.

To switch on again

Press Ο, PROGR +/–, or one of the number buttons on the

Remote Commander.

Switching off completely

Depress φ on the TV and indicator on the front of the TV lights up

in amber.

Selecting TV Programmes

Press PROGR +/– or press the number buttons.

To select a double-digit number

Press -/--, then the numbers.

For example, If you want to choose 23, press -/--, 2 and 3.

Adjusting the Volume

Press +/–.

Operating the TV Using the

Buttons on the TV

To select the programme number, press the PROGR +/– buttons.

To adjust the volume, press the

+/– buttons.

To select the video input picture, press the

button.

To reset picture and sound controls to the factory preset level

(RESET function), press PROGR +/– buttons simultaneously.

PROGR

VTR 1-2-3

MDP

SAT

RM-838

USE

MEM

RESET

For details of the video

input picture, refer to

page 24.

Watching Teletext or Video Input

Watching teletext

1 Press _ to view the teletext.

2 For teletext operation, enter a 3-digit page number with the number

buttons to select a page.

For fastext operation, press one of the coloured buttons.

For both operations, press ς (PAGE + ) for the next page or

Υ (PAGE – ) for the preceding page.

3 To go back to the normal TV picture, press Ο .

Watching a video input picture

1 Press repeatedly until the desired video input appears.

2 To go back to the normal TV picture, press Ο.

More Convenient Functions

Use the Full-Function side of the Remote Commander.

Displaying the on screen indications

• Press ∃ once to display all the indications. They will disappear

after a few seconds.

• Press ∃ twice to have the programme number and label stay on

screen. Press twice again to make the indications disappear.

Muting the sound

Press ο.

To resume normal sound, press ο again.

Displaying the time

Press #. This function is available only when teletext is broadcast.

To make the time display disappear, press # again.

Displaying the Programme Table

Press OK. A Programme Table will be displayed on the left side of

the TV screen. (See Fig. 27.)

Selecting TV programmes

Press PROGR +/– or select the desired programme position using

>+ or ?– and press OK.

To make the Programme Table disappear, press MENU.

Freezing the Picture

When watching the TV you have the possibility to “freeze” the

picture. Press

. Press the button again to return to the normal

TV picture.

Changing the Screen format

Press repeatedly to change the Screen mode as follows:

4:3 (4:3 picture)

Α Smart (imitation of 16:9 for 4:3 broadcast)

Α Zoom (imitation of 16:9 for movies broadcast in

cinemascopic format)

Α Wide (for 16:9 broadcast).

See also page 19 for more information.

For details of the teletext

operation, refer to

page 20.

PROGR

Fig. 27

BBC

SAT

TV5

C02

C15

RTL

SKY

S34

AV1

MTV

Effect

(See page 17 for more information)

Off: Normal n Dolby n Hall

Choice between different hall effects

Room n Dome n Arena

A: left channel B: right channel Stereo Mono

The selected mode of the A-µ-B indicator on the TV lights up.

Less

A: channel 1 n B: channel 2 n PAP (if PAP is switched on you

can select the PAP sound for the headphones)

Stereo n Mono

Effect

Less More

Darker

Brighter

Less

Greenish

Reddish

Softer

Sharper

Resets picture to the factory preset levels.

Normal high: obtain a high quality picture

PICTURE

CONTROL

SOUND

CONTROL

Adjusting and Setting the TV Using

the Menu

SOUND CONTROL

Graphic Equalizer

Surround Mode

Hall Effect

(only if “Hall” is on)

Dual Sound

Headphones:

2 Volume

2 Dual Sound

➝

Adjusting the Picture and Sound

Although the picture and sound are adjusted at the factory, you can

adjust them to suit your own taste. You can also select dual sound

(bilingual) programmes when available or adjust the sound for

listening with the headphones. Also you have the possibility to

adjust the sound to your individual taste using the Graphic

Equalizer and special Sound effects.

1 Press

(for picture) or (for sound) on the Remote Commander.

Press MENU and select the symbol

for Picture Control or

Sound Control, then press OK.

The PICTURE CONTROL or SOUND CONTROL menu appears.

(See Fig. 28 or Fig. 29.)

2 Using >+ or ?–, select the item you want to adjust and press OK.

The selected item changes colour. (See Fig. 30.)

3 Adjust the setting with >+ or ?– and press OK.

The cursor appears beside the next item (at the left margin). (See

Fig. 31.)

For the effect of each control, see the table below.

4 Repeat steps 2 and 3 to adjust other items.

5 Press MENU to return to TV picture.

Fig. 28

Fig. 29

Fig. 30

Fig. 31

Select and press OK

Dual Sound

Surround-Mode

Grafic Equalizer

SOUND CONTROL

Hall effect

Volume

Dual Sound (A)

[ ]Hall

[ ]

[ ]mono

Brightness

Colour

Brightness

If you have made a

mistake

Press ≅ to go back to

the previous position.

To go back to the main

Keep pressing ≅.

Notes

• HUE is only available for

NTSC colour systems.

• Hall Surround is not

available via

headphones.

Note on LINE OUT

The audio level and the

dual sound mode output

from the > jack on the

rear correspond to the

HEADPHONES

VOLUME and DUAL

SOUND settings.

When watching a video

input source with

stereo sound

You can select DUAL

SOUND to change the

sound.

PROGR

VTR 1-2-3

MDP

SAT

RM-838

USE

MEM

RESET

Effect of each control

PICTURE CONTROL

Contrast

Brightness

Colour

Hue

Sharpness

RESET

Resolution

Select and press OK

Reset

Sharpness

Brightness

Contrast

PICTURE CONTROL

Colour

Resolution (high)

Graphic Equalizer

Using this function you can individually adjust the sound by cutting

and boosting selected frequencies. You can also select between

the following modes:

Flat n Pop n Rock n Jazz n Vocal n User

1 Select “Sound Control” in the main menu, then select “Graphic

Equalizer” using >+ or ?– and press OK.

The GRAPHIC EQUALIZER menu appears (See Fig. 32).

2 Press OK. The colour of “Mode” changes. Select the desired

mode with >+ or ?– and press OK.

3 If you want to modify a mode, select the desired bar of a frequency

band using >+ or ?– and press OK. The selected frequency

changes colour. Using >+ or ?– adjust the level of frequency and

press OK. In this way you can adjust all 5 graphic bars.

4 Press MENU to return to the normal TV mode.

Using the Sleep Timer

You can select a time period after which the TV automatically

switches into standby mode.

1 Using >+ or ?– select the symbol t for “Timer” and press OK.

The TIMER menu appears (see Fig. 33).

2 Press OK.

The time period option changes colour.

3 Select the time period with >+ or ?–.

The time period (in minutes) changes as follows:

10 n 20 n 30 n 40 n 50 n 60 n 70 n 80 n 90

4 After selecting the time period, press OK.

The cursor moves back to the left margin and the timer starts

counting.

One minute before the TV switches into standby mode, a message

is displayed on the screen.

GRAPHIC EQUALIZER

Select and press OK

[User]Mode:

–

100 400 1K 4K 10K

Note: The modifications

made in “USER” mode

will be stored. All other

settings are reset to

factory-set level when

you change to another

mode.

TIMER

To switch off the timer

Select “OFF” in step 3.

To check the

remaining time

Press ∃.

To go back to the

normal TV picture

Press MENU.

Fig. 32

Fib. 33

TIMER

Select and press OK

Sleep Timer [ ]10 Min

Flat

Pop

Rock

Jazz

Vocal

User

↑

AB BA

PROGR

VTR 1-2-3

MDP

SAT

RM-838

USE

MEM

RESET

PAP (Picture and Picture)

Notes

• RGB input source

cannot be displayed in

PAP.

• PAP is not available in

the Zoom mode.

• The sound of the right

screen is only available

via the headphones.

• The picture quality of

the TV screen and

PAP may differ.

With this function you can display two screens at the same time. In

this way you can watch two TV programmes at the same time. Also

you can watch or monitor the video output from any connected

equipment (for example from a VCR) while watching TV or vice

versa. For information about connection of other equipment, refer

to page 23.

Switching PAP on and off

Press to display the screens in 8:9 format.

Press

twice to display the screens in 4:3 format.

The PAP screen will be displayed next to the main TV screen.

The PAP screen will come from the source chosen when the TV

was last used.

To switch PAP off

Press repeatedly.

Selecting PAP source

Press >.

The symbol > will be displayed at the bottom, left-hand corner of

the screen.

Press PROGR +/–, the number buttons or … to select the desired

source for the PAP screen.

Swapping screens

Press .

The main screen will switch the picture with the PAP screen.

8: 9 8: 9 4: 3

Freezing the picture

You have the possibility to “freeze” the picture of the PAP screen.

Press

once to freeze and twice to return to the normal screen.

PAP screen

Main

TV picture

AB BA

16: 9

8: 9

4: 3

Freeze

Fig. 34

Fig. 35

Fig. 36

Fig. 37

Fig. 38

Fig. 39

Operating Screen Mode/PAP using

the Menu

Using the Screen Mode menu you have the possibility to change

the aspect ratio for the TV display for wide screen effects, operate

the PAP Mode or reproduce the main picture image by image

(Strobe function).

1 Press MENU to display the main menu.

2 Select the symbol

for “Screen Mode” with >+ or ?– and press

OK. The SCREEN MODE menu appears (See Fig. 34).

You have the choice among the following modes:

4:3 for normal ratio 4:3 (See Fig. 35).

Smart: imitation of wide screen effect (16:9) for 4:3 broadcasts

(See Fig. 36).

Zoom imitation of wide screen effect (16:9) for movies broadcast

in cinemascopic format (See Fig. 37).

Wide: for 16:9 broadcasts (See Fig. 38).

a) Changing the Screen position (only for Zoom mode)

When using the Zoom mode part of the picture at the top and

bottom will be cut off. With the help of the function “Screen

position” you can move the screen up- or downwards in order to

see the cut-off part of the screen (e.g., to read the subtitles).

Using >+ or ?– select “Screen position” and press OK. The

selected item changes colour. Using >+ or ?– adjust the screen

position and press OK.

b) Strobe Mode

Using >+ or ?– select “Strobe” and press OK. Now the TV picture

is displayed image by image, creating a slow motion effect (See

Fig. 39). Using >+ or ?– select the speed of the motion (3

different speeds are available). Press OK to return to the normal

TV mode.

c) Switching PAP on and off

Using >+ or ?– select “PAP” and press OK. Using >+ or ?–

select “1” to display the PAP screen in 8:9 format, “2” for 4:3 format

and “OFF” to switch if off and press OK.

d) Freezing the PAP screen

Using >+ or ?– select “Clip Board” and press OK.

Using >+ or ?– select “On” to freeze the PAP screen and “Off” to

restore the normal picture.

PROGR

VTR 1-2-3

MDP

SAT

RM-838

USE

MEM

RESET

Auto Format

Select and press OK

Clip Board

PAP

Strobe

Screen Position

Screen Mode

[off]

[on]

[ ]

[ ]zoom

SCREEN MODE

When you want to

select the screen

mode

You can also select the

screen mode by

pressing the button

on the Remote

Commander.

off: OK

LIVELIVE

Strobe: Speed:

Auto Format

If you preset Auto Format to ON and the 16 : 9 format signal is

being transmitted, the screen mode automatically changes from

any mode to the 16 : 9 mode. When the 16 : 9 format programme is

finished, the screen mode automatically returns to the previous

mode.

1 Press MENU to display the main menu.

2 Select the symbol

for “Screen Mode” with >+ or ?– and press

OK. The SCREEN MODE menu appears.

3 Select “Auto Format” with >+ or ?– and press OK.

4 Select ON or OFF with >+ or ?– and press OK.

PROGR

VTR 1-2-3

MDP

SAT

RM-838

USE

MEM

RESET

Note

Teletext errors may

occur if the broadcasting

signals are weak.

With the simple side of

the Remote

Commander

You can switch teletext

on and off, operate

Fastext, and directly

select page numbers.

Note

Fastext operation is only

possible, if the TV station

broadcasts Fastext

signals.

Teletext

TV stations broadcast an information service called Teletext via

the TV channels.Teletext service allows you to receive various

information pages such as weather reports or news at any time

you want. For advanced teletext operation, use the buttons on the

Full-Function side of the Remote Commander.

Direct Access Functions

Switching Teletext on and off

1 Select the TV channel which carries the teletext broadcast you

want to watch.

2 Press _ to switch on teletext.

A teletext page will be displayed (usually the index page).

If there is no teletext broadcast, “No text available” is displayed on

the information line at the top of the screen.

To switch teletext off

Press Ο.

Selecting a teletext page

With direct page selection

Use the number buttons to input the three digits of the chosen

page number.

If you have made a mistake, type in any three digits. Then re-enter

the correct page number.

With page-catching

1 Select a teletext page with a page overview (e.g. index page).

2 Press OK. Using >+ or ?–, select the desired page. “Page

Catching” will be displayed on the information line. Press OK.

The requested page will appear in a few seconds.

Press _ to resume normal teletext reception.

Accessing next or preceding page

Press g (PAGE+) or G (PAGE-).

The next or preceding page appears.

Superimposing the teletext display on the TV programme

• Press _ once in teletext mode or twice in TV mode.

• Press _ again to resume normal teletext reception.

Preventing a teletext page from being updated

• Press [ (HOLD). The HOLD symbol “[” is displayed on the

information line.

• Press _ to resume normal teletext reception.

Using Fastext

With Fastext you can access pages with one key stroke.

When a Fastext page is broadcast, a colour-coded menu will

appear at the bottom of the screen. The colours of this menu

correspond to the red, green, yellow and blue buttons on the

Remote Commander.

Press the corresponding coloured button on the Remote

Commander which corresponds to the colour-coded menu. The

page will be displayed after a few seconds.

Sidan laddas ...

Sony KL-37W1 Bruksanvisning

varumärke: Sony

Modell: KL-37W1

Typ: Bruksanvisning

Denna manual är också lämplig för

KL-50W1

Ladda ner pdf

Rapportera

på andra språk

español: Sony KL-37W1 El manual del propietario
português: Sony KL-37W1 Manual do proprietário
English: Sony KL-37W1 Owner's manual

Sony KL-37W1 Bruksanvisning

Denna manual är också lämplig för

Sony KL-37W1 Bruksanvisning

på andra språk

Relaterade papper

Andra dokument