Makita CL002G Användarmanual

Typ
Användarmanual
CL002G
EN Cordless Cleaner INSTRUCTION MANUAL 9
SV Sladdlös dammsugare BRUKSANVISNING 18
NO Batteridrevet støvsuger BRUKSANVISNING 27
FI Akkukäyttöinen pölynimuri KÄYTTÖOHJE 36
DA Akku støvsuger BRUGSANVISNING 45
LV Bezvadu tīrītājs LIETOŠANAS INSTRUKCIJA 54
LT Belaidis siurblys NAUDOJIMO INSTRUKCIJA 63
ET Juhtmeta käsitolmuimeja KASUTUSJUHEND 72
RU Аккумуляторный пылесос РУКОВОДСТВО ПО
ЭКСПЛУАТАЦИИ 81
2
Fig.1
3
11
2
Fig.2
1
2
Fig.3
4
1
3
2
2
1
Fig.4
3
2
1
Fig.5
Fig.6
1
2
Fig.7
1
23
Fig.8
3
1
Fig.9
Fig.10
Fig.11
Fig.12
1
Fig.13
1
2
Fig.14
Fig.15
1
23
Fig.16
4
1
Fig.17
Fig.18
Fig.19
Fig.20
1
Fig.21
3
2
1
Fig.22
1
2
Fig.23
Fig.24
5
1
Fig.25
3
2
1
Fig.26
1
2
Fig.27
1
2
Fig.28
1
2
3
Fig.29
Fig.30
1
Fig.31
2
1
Fig.32
6
1
Fig.33
1
2
Fig.34
1
2
Fig.35
1
2
Fig.36
Fig.37
Fig.38
Fig.39
1
Fig.40
7
1
Fig.41
1
Fig.42
1
Fig.43
3
4
1
2
5
Fig.44
23
1
4
Fig.45
2
1
Fig.46
8
2
1
Fig.47
1
2
Fig.48
1
2
3
Fig.49
9ENGLISH
ENGLISH (Original instructions)
WARNING
This appliance can be used by children aged from 8 years and above and persons with reduced physical, sen-
sory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruc-
tion concerning use of the appliance in a safe way and understand the hazards involved.
Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children with-
out supervision.
See the chapter “SPECIFICATIONS” for the type reference of the battery.
See the section “Installing or removing battery cartridge” for how to remove or install the battery.
When disposing the battery cartridge, remove it from the tool and dispose of it in a safe place. Follow your local
regulations relating to disposal of battery.
If the tool is not used for a long period of time, the battery must be removed from the tool.
Do not short the battery cartridge.
See the chapter “MAINTENANCE” for the appropriate details of precautions during user maintenance.
SPECIFICATIONS
Model: CL002G
Capacity with dust bag 500 mL
with paper lter 330 mL
Continuous use
(with battery BL4025)
1 (Quiet mode) Approx. 80 min
2 (Normal speed mode) Approx. 40 min
3 (High speed mode) Approx. 25 min
4 (Max speed mode) Approx. 16 min
Overall length (with pipe, nozzle, and battery BL4025) 1,066 mm
Rated voltage D.C. 36 V - 40 V max
Net weight 1.8 - 2.4 kg
Due to our continuing program of research and development, the specications herein are subject to change
without notice.
Specications may dier from country to country.
The weight does not include accessories but battery cartridge(s). The lightest and heaviest combination weight
of the appliance and battery cartridge(s) are shown in the table.
Applicable battery cartridge and charger
Battery cartridge BL4020* / BL4025* / BL4040* / BL4050F
* : Recommended battery
Charger DC40RA / DC40RB / DC40RC
Some of the battery cartridges and chargers listed above may not be available depending on your region of
residence.
WARNING: Only use the battery cartridges and chargers listed above. Use of any other battery cartridges
and chargers may cause injury and/or re.
Symbols
The followings show the symbols which may be used
for the equipment. Be sure that you understand their
meaning before use.
Read the instruction manual.
A representative battery applicable to this
product.
10 ENGLISH
Ni-MH
Li-ion
Only for EU countries
Due to the presence of hazardous com-
ponents in the equipment, waste electrical
and electronic equipment, accumulators
and batteries may have a negative impact
on the environment and human health.
Do not dispose of electrical and electronic
appliances or batteries with household
waste!
In accordance with the European Directive
on waste electrical and electronic equip-
ment and on accumulators and batteries
and waste accumulators and batteries,
as well as their adaptation to national law,
waste electrical equipment, batteries and
accumulators should be stored separately
and delivered to a separate collection point
for municipal waste, operating in accor-
dance with the regulations on environmen-
tal protection.
This is indicated by the symbol of the
crossed-out wheeled bin placed on the
equipment.
Intended use
The tool is intended for collecting dry dust.
SAFETY WARNINGS
Cordless cleaner safety warnings
WARNING: IMPORTANT! READ CAREFULLY
all safety warnings and all instructions BEFORE
USE. Failure to follow the warnings and instructions
may result in electric shock, re and/or serious injury.
1. Do not expose to rain. Store indoors.
2.
Do not allow to be used as a toy. Close attention
is necessary when used by or near children.
3. Use only as described in this manual. Use only
manufacturer's recommended attachments.
4. Do not use with damaged battery. If appliance
is not working as it should, has been dropped,
damaged, left outdoors, or dropped into water,
return it to a service center.
5. Do not handle appliance with wet hands.
6.
Do not put any object into openings. Do not use
with any opening blocked; keep free of dust, lint,
hair, and anything that may reduce air ow.
7. Keep hair, loose clothing, ngers, and all parts
of body away from openings and moving parts.
8. Turn o all controls before removing the
battery.
9. Use extra care when cleaning on stairs.
10. Do not use to pick up ammable or combusti-
ble liquids, such as gasoline, or use in areas
where they may be present.
11. Use only the charger supplied by the manufac-
turer to recharge.
12.
Do not pick up anything that is burning or smok-
ing, such as cigarettes, matches, or hot ashes.
13. Do not use without dust bag and/or lters in
place.
14. Do not charge the battery outdoors.
15. Recharge only with the charger specied by
the manufacturer. A charger that is suitable for
one type of battery pack may create a risk of re
when used with another battery pack.
16. Use appliances only with specically desig-
nated battery packs. Use of any other battery
packs may create a risk of injury and re.
17. When (the) battery pack is not in use, keep
it away from other metal objects, like paper
clips, coins, keys, nails, screws or other small
metal objects, that can make a connection
from one terminal to another.
18. Under abusive conditions, liquid may be
ejected from the battery; avoid contact. If con-
tact accidentally occurs, ush with water.
19. Do not use a battery pack or appliance that
is damaged or modied. Damaged or modied
batteries may exhibit unpredictable behaviour
resulting in re, explosion or risk of injury.
20. Do not expose a battery pack or appliance
to re or excessive temperature. Exposure
to re or temperature above 130 °C may cause
explosion.
21. Follow all charging instructions and do not
charge the battery pack or appliance outside
the temperature range specied in the instruc-
tions. Charging improperly or at temperatures
outside the specied range may damage the
battery and increase the risk of re.
SAVE THESE INSTRUCTIONS.
ADDITIONAL SAFETY RULES
This appliance is intended for household use.
1. Read this instruction manual and the charger
instruction manual carefully before use.
2. Do not pick up the following materials:
Hot materials such as lit cigarettes or
spark/metal dust generated by grinding/
cutting metal
Flammable materials such as gasoline,
thinner, benzine, kerosene or paint
Explosive materials like nitroglycerin
Ignitable materials such as Aluminum,
zinc, magnesium, titanium, phosphorus
or celluloid
Wet dirt, water, oil or the like
Hard pieces with sharp edges, such as
wood chips, metals, stones, glasses,
nails, pins or razors
Powder to clot such as cement or toner
Conductive dust such as metal or carbon
Fine particle like concrete dust
Such action may cause re, injury and/or prop-
erty damage.
3. Stop operation immediately if you notice any-
thing abnormal.
4. If you drop or strike the cleaner, check it care-
fully for cracks or damage before operation.
5.
Do not bring close to stoves or other heat sources.
6. Do not block the intake hole or vent holes.
SAVE THESE INSTRUCTIONS.
11 ENGLISH
Important safety instructions for
battery cartridge
1. Before using battery cartridge, read all instruc-
tions and cautionary markings on (1) battery
charger, (2) battery, and (3) product using
battery.
2. Do not disassemble or tamper with the battery
cartridge. It may result in a re, excessive heat,
or explosion.
3. If operating time has become excessively
shorter, stop operating immediately. It may
result in a risk of overheating, possible burns
and even an explosion.
4. If electrolyte gets into your eyes, rinse them
out with clear water and seek medical atten-
tion right away. It may result in loss of your
eyesight.
5. Do not short the battery cartridge:
(1) Do not touch the terminals with any con-
ductive material.
(2) Avoid storing battery cartridge in a con-
tainer with other metal objects such as
nails, coins, etc.
(3) Do not expose battery cartridge to water
or rain.
A battery short can cause a large current
ow, overheating, possible burns and even a
breakdown.
6. Do not store and use the tool and battery car-
tridge in locations where the temperature may
reach or exceed 50 °C (122 °F).
7. Do not incinerate the battery cartridge even if
it is severely damaged or is completely worn
out. The battery cartridge can explode in a re.
8. Do not nail, cut, crush, throw, drop the battery
cartridge, or hit against a hard object to the
battery cartridge. Such conduct may result in a
re, excessive heat, or explosion.
9. Do not use a damaged battery.
10. The contained lithium-ion batteries are subject
to the Dangerous Goods Legislation require-
ments.
For commercial transports e.g. by third parties,
forwarding agents, special requirement on pack-
aging and labeling must be observed.
For preparation of the item being shipped, consult-
ing an expert for hazardous material is required.
Please also observe possibly more detailed
national regulations.
Tape or mask o open contacts and pack up the
battery in such a manner that it cannot move
around in the packaging.
11. When disposing the battery cartridge, remove
it from the tool and dispose of it in a safe
place. Follow your local regulations relating to
disposal of battery.
12. Use the batteries only with the products
specied by Makita. Installing the batteries to
non-compliant products may result in a re, exces-
sive heat, explosion, or leak of electrolyte.
13. If the tool is not used for a long period of time,
the battery must be removed from the tool.
14. During and after use, the battery cartridge may
take on heat which can cause burns or low
temperature burns. Pay attention to the han-
dling of hot battery cartridges.
15. Do not touch the terminal of the tool imme-
diately after use as it may get hot enough to
cause burns.
16. Do not allow chips, dust, or soil stuck into the
terminals, holes, and grooves of the battery
cartridge. It may cause heating, catching re,
burst and malfunction of the tool or battery car-
tridge, resulting in burns or personal injury.
17. Unless the tool supports the use near
high-voltage electrical power lines, do not use
the battery cartridge near a high-voltage elec-
trical power lines. It may result in a malfunction
or breakdown of the tool or battery cartridge.
18. Keep the battery away from children.
SAVE THESE INSTRUCTIONS.
CAUTION: Only use genuine Makita batteries.
Use of non-genuine Makita batteries, or batteries that
have been altered, may result in the battery bursting
causing res, personal injury and damage. It will
also void the Makita warranty for the Makita tool and
charger.
Tips for maintaining maximum
battery life
1. Charge the battery cartridge before completely
discharged. Always stop tool operation and
charge the battery cartridge when you notice
less tool power.
2. Never recharge a fully charged battery car-
tridge. Overcharging shortens the battery
service life.
3. Charge the battery cartridge with room tem-
perature at 10 °C - 40 °C (50 °F - 104 °F). Let
a hot battery cartridge cool down before
charging it.
4. When not using the battery cartridge, remove
it from the tool or the charger.
5. Charge the battery cartridge if you do not use
it for a long period (more than six months).
12 ENGLISH
FUNCTIONAL
DESCRIPTION
CAUTION: Always be sure that the tool is
switched o and the battery cartridge is removed
before adjusting or checking function on the tool.
CAUTION: Take care not to trap nger(s)
between cleaner and battery as shown in diagram
when loading battery. Trapping nger(s) may cause
injury.
Fig.1
Installing or removing battery cartridge
CAUTION: Always switch o the tool before
installing or removing of the battery cartridge.
CAUTION: Hold the tool and the battery car-
tridge rmly when installing or removing battery
cartridge. Failure to hold the tool and the battery
cartridge rmly may cause them to slip o your hands
and result in damage to the tool and battery cartridge
and a personal injury.
Fig.2: 1. Red indicator 2. Button 3. Battery cartridge
To remove the battery cartridge, slide it from the tool
while sliding the button on the front of the cartridge.
To install the battery cartridge, align the tongue on the
battery cartridge with the groove in the housing and slip
it into place. Insert it all the way until it locks in place
with a little click. If you can see the red indicator as
shown in the gure, it is not locked completely.
CAUTION: Always install the battery cartridge
fully until the red indicator cannot be seen. If not,
it may accidentally fall out of the tool, causing injury to
you or someone around you.
CAUTION: Do not install the battery cartridge
forcibly. If the cartridge does not slide in easily, it is
not being inserted correctly.
Battery protection system
The tool is equipped with a tool/battery protection sys-
tem. This system automatically cuts o power to the
motor to extend tool and battery life. The tool will auto-
matically stop during operation if the tool or battery is
placed under one of the following conditions.
Overloaded:
The tool/battery is operated in a manner that causes it
to draw an abnormally high current.
In this situation, turn the tool o and stop the application
that caused the tool to become overloaded. Then turn
the tool on to restart.
If the tool does not start, the battery is overheated. In
this situation, let the battery cool before turning the tool
on again.
Low battery voltage:
The remaining battery capacity is too low and the tool
will not operate. In this situation, remove and recharge
the battery.
Protections against other causes:
Protection system is also designed for other causes
that could damage the tool and allows the tool to stop
automatically. Take all the following steps to clear the
causes, when the tool has been brought to a temporary
halt or stop in operation.
1.
Turn the tool o, and then turn it on again to restart.
2. Charge the battery(ies) or replace it/them with
recharged battery(ies).
3. Let the tool and battery(ies) cool down.
If no improvement can be found by restoring protection
system, then contact your local Makita Service Center.
Indicating the remaining battery capacity
Press the check button on the battery cartridge to indi-
cate the remaining battery capacity. The indicator lamps
light up for a few seconds.
Fig.3: 1. Indicator lamps 2. Check button
Indicator lamps Remaining
capacity
Lighted O Blinking
75% to 100%
50% to 75%
25% to 50%
0% to 25%
Charge the
battery.
The battery
may have
malfunctioned.
NOTE: Depending on the conditions of use and the
ambient temperature, the indication may dier slightly
from the actual capacity.
NOTE: The rst (far left) indicator lamp will blink when
the battery protection system works.
Switch action
Fig.4:
1. Suction power change button 2. ON/OFF button
To start the cleaner, simply push the ON/OFF button. To
switch o, push the ON/OFF button again.
You can change the suction power of the cleaner in
four steps by pushing the suction power change button.
Each push on this button repeats the Quiet/Normal/
High/Max mode in a cycle.
Level Indication Mode
1Quiet mode
2
Normal speed mode
3High speed mode
4Max speed mode
13 ENGLISH
NOTE: You can change the suction power before
turning on the cleaner.
NOTE: The cleaner starts the operation with the
same suction power as the last operation.
Lighting up the lamp
CAUTION: Do not look in the light or see the
source of light directly.
To turn on the lamp, push the suction power change
button. The lamp goes o in approximately 10 seconds.
While the cleaner is running, the lamp turns on.
The lamp goes out approximately 10 seconds after
stopping operation.
NOTE: When the remaining battery capacity gets low,
the lamp starts blinking. The timing, at which the lamp
starts blinking depends on the temperature at work
place and the battery cartridge conditions.
Fig.5: 1. Suction power change button 2. ON/OFF
button 3. Lamp
ASSEMBLY
CAUTION: Always be sure that the tool is
switched o and the battery cartridge is removed
before carrying out any work on the tool.
Dust bag and paper lter
Install either dust bag or paper lter before using cleaner.
Use the dust stopper when installing either dust bag or paper lter.
Dust bag are usable many times repeatedly by cleaning it out.
Paper lter is a throw-away type. Throw away the entire
paper lter without emptying when it has become full.
NOTICE: To prevent dust from getting into the
motor:
Make sure that the dust bag or paper lter is
installed before use.
Insert the dust stopper together with the
dust bag or paper lter all the way into the
slots when installing them.
Do not use a broken or ripped bag.
Otherwise the motor may be broken.
NOTICE: Do not fold the cardboard at its open-
ing when installing the paper lter.
NOTICE: Never throw away the dust stopper
because it needs to be used repeatedly whenever
either the dust bag or the paper lter is used.
NOTICE: The paper lter for the cleaner is an
important component for maintaining the tool
performance. Using other than the genuine paper
lter may cause smokes or ignition.
NOTE: When the dust bag or the paper lter is not
installed in the cleaner, the front cover does not close
completely.
Fig.6
Installing dust bag
Use the dust stopper when installing dust bag. Be
careful not to take the upper side for the lower side by
mistake because they are dierent each other.
Fig.7: 1. Upper side of dust stopper 2. Lower side of
dust stopper
1. Insert the protrusion of the dust bag into the lower
groove on the dust stopper as shown in the gure.
Fig.8: 1. Dust stopper 2. Lower groove 3. Dust bag
There is no distinction between the upper and lower
sides of the dust bag. You may insert its protrusion of
either side into the lower groove of the dust stopper.
Fig.9: 1. Lower groove
2.
Overlap the frame of dust stopper with that of the dust bag.
Fig.10
3. Place the dust stopper and the dust bag together
into the cleaner cavity in the same direction of arrow on
the dust stopper. Insert them all the way into the slots in
the cleaner cavity.
Fig.11
4.
Spread the cloth part of the dust bag inside the cleaner.
Fig.12
5. Close the front cover completely.
Fig.13: 1. Front cover
Installing the paper lter
Use the dust stopper also when installing paper lter.
Be careful not to take the upper side for the lower side
by mistake because they are dierent each other.
Fig.14: 1. Upper side of dust stopper 2. Lower side
of dust stopper
1. Unfold the entrance of the paper lter before
setting it on the dust stopper.
Fig.15
2. Insert the protrusion of the paper lter into the
lower groove on the dust stopper as shown in the gure.
Fig.16: 1. Dust stopper 2. Lower groove 3. Paper
lter
There is no distinction between the upper and lower
sides of the paper lter. You may insert its protrusion of
any side into the lower groove of the dust stopper.
Fig.17: 1. Lower groove
3. Overlap the frame of dust stopper with that of the
paper lter.
Fig.18
4. Place the dust stopper and the paper lter
together into the cleaner cavity in the same direction of
arrow on the dust stopper. Insert them all the way into
the slots in the cleaner cavity.
Fig.19
5. Spread the container part of the paper lter inside
the cleaner.
Fig.20
6. Close the front cover completely.
Fig.21: 1. Front cover
14 ENGLISH
OPERATION
CAUTION: Do not move your face close to
the air vent when operating the cleaner. If foreign
objects are blown into eyes, it may result in personal
injury.
Installing and removing cleaner
attachments
CAUTION: After installing attachments, check
if they are securely installed. If the attachments are
installed imperfectly, they may come o and cause
personal injury.
CAUTION: Be careful not to hit your hand on
the wall etc. when removing the attachments.
When using attachment with lock
function
To install attachment, insert it to the suction inlet of the
cleaner until it clicks. Make sure that the attachment is
locked.
Fig.22: 1. Suction inlet 2. Attachment with lock
function 3. Hook
NOTICE: When installing the attachment with
lock function, be sure to align the release button
on the cleaner with the hook on the attachment. If
they are not aligned, the attachment will not be locked
and may come o from the cleaner.
To remove, pull the attachment while pushing the
release button.
Fig.23: 1. Release button 2. Attachment with lock
function
When using attachment without lock
function
NOTICE: To connect attachment without lock
function, twist and insert it securely into the suc-
tion inlet of the cleaner. To disconnect the attach-
ment, pull it away while twisting.
Fig.24
Cleaning (Suction)
Nozzle
Attach the nozzle to clean o tables, desks, furniture,
etc. The nozzle slips on easily.
Fig.25: 1. Nozzle
Nozzle + Extension wand (Straight pipe)
The extension wand ts in between the nozzle and the
cleaner itself. This arrangement is convenient for clean-
ing a oor in a standing position.
Fig.26: 1. Cleaner body 2. Extension wand
3. Nozzle
Corner nozzle
Fit on the corner nozzle for cleaning corners and crev-
ices of a car or furniture.
Fig.27: 1. Corner nozzle 2. Cleaner body
You can store the corner nozzle in the nozzle holder.
Fig.28: 1. Nozzle holder 2. Corner nozzle
CAUTION: Be careful not to trap nger(s)
between the corner nozzle and the nozzle holder.
Trapping nger(s) may cause injury.
Corner nozzle + Extension wand
(Straight pipe)
In tight quarters where the cleaner itself cannot
squeeze in, or in high places hard to reach, use this
arrangement.
Fig.29: 1. Corner nozzle 2. Extension wand
3. Cleaner body
Cleaning without nozzle
You can pick up powder and dust without nozzle.
Fig.30
For picking up dust on a oor in a standing position, it is
convenient to attach the extension wand (straight pipe)
to the cleaner.
Fig.31: 1. Extension wand (Straight pipe)
Disposing of dust
CAUTION: Empty the cleaner before it
becomes too full, or the suction force weakens.
CAUTION: When closing the front cover, be
careful not to pinch your ngers.
NOTICE: Never throw away the dust stopper
because it should be used whenever either the
dust bag or the paper lter is used.
NOTICE: When the dust bag/paper lter is not
inside of the cleaner, the front cover does not
close completely. Do not force to close the front
cover. It may result in deforming or breakage of
the tool.
NOTICE: When disposing of dust, also clean the
room for the dust bag/paper lter. The remaining
dust and dirt in the room may cause the sponge lter
to be clogged or the motor to be damaged.
1. Push the button to open the front cover. Opening
it until a click is heard allows a positive stop at that
position.
Fig.32: 1. Front cover 2. Button
2. Pull out both the orange-colored dust stopper and
dust bag/paper lter together at the same time.
Fig.33: 1. Dust stopper
15 ENGLISH
3. Perform the procedures below depending on the
dust container type:
When using the dust bag
Remove the dust stopper and empty the dust bag.
Fig.34: 1. Dust stopper 2. Dust bag
When using the paper lter
Remove the dust stopper and dispose of the paper lter.
Fig.35: 1. Dust stopper 2. Paper lter
4. Place the dust bag/new paper lter and dust stop-
per together into the cleaner and close the front cover.
NOTE: The cleaner is constructed in such a way that
the front cover comes o when trying to force the
front cover open at the angle of more than 90°. If the
front cover comes o, insert it into the front cover joint
in place.
Fig.36: 1. Front cover 2. Front cover joint
MAINTENANCE
CAUTION: Always be sure that the tool is
switched o and the battery cartridge is removed
before attempting to perform inspection or
maintenance.
To maintain product SAFETY and RELIABILITY,
repairs, any other maintenance or adjustment should
be performed by Makita Authorized or Factory Service
Centers, always using Makita replacement parts.
After use
CAUTION: Putting the cleaner against the
wall without any other support may cause the
cleaner to fall down, resulting in personal injury
or damage to the cleaner.
Fig.37
Cleaning
CAUTION: Clean dust bags and lters when
they become clogged. Continued use in the clogged
condition may result in heating or re.
NOTICE: Never use gasoline, benzine, thinner,
alcohol or the like. Discoloration, deformation or
cracks may result.
NOTICE: Do not blow dust sticking on the
cleaner and lters by air duster. It brings dust into
the housing and causes failure.
NOTICE: After washing dust bags and
sponge lters, dry them thoroughly before use.
Insuciently dried lters may cause poor suction and
shorten the service life of the motor.
NOTICE: After cleaning dust bags and sponge
lters, be sure to re-install them before use. If
you use the cleaner without dust bags and sponge
lters, dust comes into the motor housing and cause
malfunction.
Cleaner body
From time to time wipe o the outside (cleaner body) of
the cleaner using a cloth dampened in soapy water.
Clean out also the suction opening, dust bag/paper lter
mounting area and the dust stopper.
Fig.38
Dust bag
Wash the dust bag in soapy water when it is clogged
with dust and the cleaner power becomes weak. Dry it
out thoroughly before use. An insuciently dried lter
may cause poor suction and shorten the service life of
the motor.
Fig.39
NOTE: Paper lter is a throw-away type.
Dust stopper
Wipe dust o from the dust stopper.
Remove dust and dirt on the sponge part by lightly
tapping it.
Fig.40: 1. Sponge part
Removing and installing the sponge
lter
CAUTION: After cleaning sponge lter, be
sure to install it on the cleaner. If washed in water,
dry it up before installing. An insuciently dried
sponge lter may shorten the service life of the motor.
When the sponge lter is clogged with dust, remove it
from the cleaner and then wipe it o or wash in water.
To remove the sponge lter, remove the dust bag or
paper lter and then pinch and take the sponge lter
out.
Fig.41: 1. Sponge lter
Press in the whole edge of the sponge lter against the
recessed wall inside the dust bag/paper lter mounting
area.
Fig.42: 1. Recessed wall
Wall mount for cordless cleaner
Optional accessory
NOTE: The screw to mount the holder is not included.
Prepare a screw which ts with the material to screw
into.
Attach the wall mount for cordless cleaner to a hard
wooden wall, beam or column, where the wall mount
for cordless cleaner can be rmly secured. Always be
sure that the wall mount for cordless cleaner is securely
attached before hanging the cleaner.
Fig.43: 1. Wall mount for cordless cleaner
CAUTION: Do not hang the cleaner to the wall
mount violently or hang other appliances than the
cleaner.
16 ENGLISH
Troubleshooting
Before asking for repairs, check the following points.
Symptom Area to be investigated Fixing method
Weak suction power
Is dust bag or paper lter full of dust? Empty dust bag or paper lter.
Is dust bag or sponge lter clogged? Dust down or wash dust bag and sponge
lter.
Is paper lter clogged? Replace paper lter.
Is battery cartridge discharged? Charge battery cartridge.
Not working Is battery cartridge discharged? Charge battery cartridge.
Abnormal noise and vibration come
out
Is dust bag or sponge lter clogged? Dust down or wash dust bag and sponge
lter.
Is paper lter clogged? Replace paper lter.
Anything to block openings or holes? Clean any dust and objects out of nozzles,
pipes and air openings.
Is suction inlet of nozzle or pipe closed? Uncover and open suction inlet of nozzle
and pipe.
Dust case cover does not close Is dust bag or paper lter set? Set dust bag or paper lter.
CAUTION: Do not attempt to repair the cleaner by yourself.
OPTIONAL
ACCESSORIES
CAUTION: These accessories or attachments
are recommended for use with your Makita tool
specied in this manual. The use of any other
accessories or attachments might present a risk of
injury to persons. Only use accessory or attachment
for its stated purpose.
If you need any assistance for more details regard-
ing these accessories, ask your local Makita Service
Center.
Extension wand (Straight pipe)
• Nozzle
Nozzle for carpet
Shelf brush
Corner nozzle
Round brush
Flexible hose
Dust bag
Paper lter
Free nozzle
Seat nozzle
Crevice nozzle
Wall mount for cordless cleaner
Cyclone attachment
Tool bag
Makita genuine battery and charger
NOTE: Some items in the list may be included in the
tool package as standard accessories. They may
dier from country to country.
Cyclone attachment
Fig.44: 1. Release button 2. Hook 3. Extension
wand (Straight pipe) 4. Cyclone attachment
5. Suction inlet
About the cyclone attachment
Using the cleaner with the cyclone attachment installed
reduces the amount of dust that enters the dust bag,
which helps to prevent the suction force from weaken-
ing. In addition, cleaning after use is also simple.
CAUTION: Always be sure that the tool is
switched o and the battery cartridge is removed
before carrying out any work on the tool. If the
battery cartridge is left inserted, the cleaner may start
unexpectedly and result in injury.
CAUTION: Clean the mesh lter of the
cyclone attachment and the dust bag of the
cleaner unit when they become clogged.
Continued use in the clogged condition may result in
heating or smoke.
NOTICE: When the cyclone attachment is
attached, do not use the cleaner in the horizontal
or upward facing condition. Doing so may cause
the mesh lter to become clogged.
NOTICE: Always use the cleaner with the dust
bag installed, even when using the cyclone
attachment. Using the cleaner without the dust bag
installed may result in a motor malfunction.
17 ENGLISH
NOTE: Check that the cyclone attachment, cleaner,
and extension wand (straight pipe) are locked prop-
erly before use.
NOTE: Empty the dust case of the cyclone attach-
ment and the dust bag of the cleaner when dust has
accumulated. Continued use will result in weakened
suction force.
NOTE: You can also use the cyclone attachment with-
out lock function.
NOTE: To install or remove the cyclone attachment,
refer to the section "Installing and removing cleaner
attachments".
Disposing of dust
When dust has accumulated up to the full line of the
dust case, follow the procedure below and dispose of
the dust.
1. Hold the dust case rmly, press and hold the two
buttons, and remove the dust case.
Fig.45: 1. Full line 2. Dust case 3. Button (two
locations) 4. Mesh lter
2. Dispose of the dust inside the dust case and
remove any dust and powder adhered to the surface of
the mesh lter.
3. Insert the dust case all the way until the two but-
tons lock with a click.
Fig.46: 1. Dust case 2. Button (two locations)
CAUTION: When reassembling the dust case,
be careful not to pinch your ngers.
NOTE: Check that the cyclone attachment, cleaner,
and extension wand (straight pipe) are locked prop-
erly before restarting operation.
NOTE: If the suction force does not recover even
after disposing of the dust and cleaning the mesh
lter, check whether dust has accumulated in the dust
bag of the cleaner or clogging has occurred.
NOTE: The dust may y up when disposing from the
cyclone attachment. Be careful not to let dust get into
your eyes.
Cleaning
CAUTION: After washing the cyclone attach-
ment, dry it thoroughly before use. Insuciently
dried components may cause an electrical shock or
damage to the appliance.
When the dust case becomes dirty or the mesh lter is
clogged, remove and wash them with water. (Refer to
“Disposing of dust” for the removal procedure.)
Dry the parts thoroughly before reinstallation and use.
Fig.47: 1. Dust case 2. Mesh lter
When the mesh lter gets dirty badly, clean it in the
following procedures.
1. Turn the mesh lter counterclockwise and remove
it while the hooks are unlocked.
Fig.48: 1. Mesh lter 2. Hook
2. Remove the dust on the mesh lter and then wash
it with water. After that, dry it thoroughly.
3. Insert the mesh lter into the base while the hooks
are aligned with the port. Turn the mesh lter clockwise
until the hooks are locked with a click. Make sure that
the mesh lter is installed securely.
Fig.49: 1. Mesh lter 2. Hook 3. Port
18 SVENSKA
SVENSKA (Originalinstruktioner)
VARNING
Denna apparat kan användas av barn från 8 års ålder och äldre samt personer med nedsatt fysisk, sensorisk
eller mental kapacitet eller brist på erfarenhet och kunskap förutsatt att de har fått handledning eller instruktio-
ner om hur apparaten används på rätt sätt och förstår riskerna som det medför.
Barn ska inte leka med apparaten. Rengöring och användarunderhåll ska inte utföras av barn utan tillsyn.
Se batteriets typreferens i kapitlet ”SPECIFIKATIONER”.
Se i avsnittet ”Montera eller demontera batterikassetten” hur du tar bort eller installerar batteriet.
När batterikassetten ska kasseras måste den tas bort från verktyget och kasseras på ett säkert sätt. Följ lokala
föreskrifter beträande avfallshantering av batteriet.
Om verktyget inte används under en lång tid måste batteriet tas bort från verktyget.
Kortslut inte batterikassetten.
Se uppgifter om lämpliga försiktighetsåtgärder vid användarunderhåll i kapitlet ”UNDERHÅLL”.
SPECIFIKATIONER
Modell: CL002G
Kapacitet med dammpåse 500 mL
med papperslter 330 mL
Kontinuerlig användning
(med batteri BL4025)
1 (tyst läge) ca 80 min
2 (normalt hastighetsläge) ca 40 min
3 (höghastighetsläge) ca 25 min
4 (maxhastighetsläge) ca 16 min
Total längd (med rör, munstycke och batteri BL4025) 1 066 mm
Märkspänning 36 V - 40 V likström max
Nettovikt 1,8 - 2,4 kg
grund av vårt pågående program för forskning och utveckling kan dessa specikationer ändras utan föregå-
ende meddelande.
Specikationer kan variera mellan olika länder.
Vikten inkluderar inte tillbehör men batterikassett(er). Den lättaste och tyngsta viktkombinationen för maskin
och batterikassett(er) visas i tabellen.
Tillgänglig batterikassett och laddare
Batterikassett BL4020* / BL4025* / BL4040* / BL4050F
* : Rekommenderat batteri
Laddare DC40RA / DC40RB / DC40RC
Vissa av batterikassetterna och laddarna på listan ovan kanske inte nns tillgängliga i din region.
VARNING: Använd endast batterikassetter och laddare från listan ovan. Användning av andra batterikas-
setter och laddare kan orsaka personskada och/eller brand.
Symboler
Följande visar symbolerna som kan användas för
utrustningen. Se till att du förstår innebörden innan
användning.
Läs igenom bruksanvisningen.
Ett representativt batteri som kan använ-
das med den här produkten.
19 SVENSKA
Ni-MH
Li-ion
Gäller endast inom EU
P.g.a. förekomsten av farliga komponenter
i utrustningen kan avfall innehållande
elektrisk och elektronisk utrustning, acku-
mulatorer och batterier ha negativ inverkan
på miljön och människors hälsa.
Kassera inte elektriska och elektro-
niska apparater eller batterier ihop med
hushållsavfall!
I enlighet med EU-direktiven om avfall
som utgörs av eller innehåller elektrisk och
elektronisk utrustning och om batterier och
ackumulatorer och förbrukade batterier
och ackumulatorer, och dess införlivande
i nationell lagstiftning, bör förbrukad elek-
trisk och elektronisk utrustning, batterier
och ackumulatorer förvaras separat och
transporteras till en särskild uppsamlings-
plats för kommunalt avfall, som drivs i
enlighet med regelverket för miljöskydd.
Detta anges av symbolen med den över-
kryssade soptunnan på hjul som sitter på
utrustningen.
Avsedd användning
Det här redskapet är avsett för insamling av torrt damm.
SÄKERHETSVARNINGAR
Säkerhetsvarningar för sladdlös
dammsugare
VARNING: VIKTIGT! LÄS NOGGRANT igenom
alla säkerhetsvarningar och anvisningar FÖRE
ANVÄNDNING. Underlåtenhet att följa varningar
och instruktioner kan leda till elstötar, brand och/eller
allvarliga personskador.
1.
Utsätt inte för regn. Förvara maskinen inomhus.
2. Tillåt inte att den används som en leksak.
Stor uppmärksamhet är nödvändigt när den
används i barns närhet.
3. Använd den endast enligt beskrivningen i
bruksanvisningen. Använd endast tillverka-
rens rekommenderade tillsatser.
4. Använd inte maskinen med ett skadat batteri.
Om maskinen inte arbetar som den ska, har
tappats i marken, skadats, lämnats utomhus
eller hamnat i vatten ska den skickas till
servicecentret.
5. Var inte blöt om händerna när du handskas
med maskinen.
6.
Placera inte något föremål i öppningarna. Använd
inte dammsugaren om någon av öppningarna är
blockerade och håll den ren från damm, trådar,
hår samt allt som kan minska luftödet.
7.
Håll hår, löst sittande kläder, ngrar och alla
kroppsdelar bort från öppningar och rörliga delar.
8. Stäng av alla kontroller innan batteriet tas bort.
9. Var extra försiktig vid rengöring av trappor.
10. Använd inte maskinen för att plocka upp
brännbara eller lättantändliga vätskor, såsom
bensin, eller använd inte maskinen på platser
där sådana vätskor förvaras.
11. Använd endast den laddare som tillverkaren
har skickat med för att ladda batteriet.
12. Plocka inte upp något som brinner eller glöder,
såsom cigaretter, tändstickor eller glödande
aska.
13. Använd inte utan dammpåse och/eller ltren
monterade på plats.
14. Ladda inte batteriet utomhus.
15. Ladda endast med den batteriladdare som
angetts av tillverkaren. En laddare som passar
en viss typ av batterier kan skapa risk för brand
när den används tillsammans med annat batteri.
16. Använd endast apparater med specikt
angivna batteripaket. Om andra batterier
används kan risken för personskada och brand
öka.
17. När batteriet inte används bör det hållas borta
från andra metallföremål så som gem, mynt,
nycklar, spik, skruv eller andra små metall-
föremål som kan skapa en anslutning mellan
batteripolerna.
18. Under hårda förhållande kan det komma
vätska ur batteriet. Undvik kontakt. Spola med
vatten om kontakt ändå råkar uppstå.
19. Använd inte ett batteripaket eller en apparat
som har skadats eller ändrats. Skadade eller
ändrade batterier kan uppföra sig opålitligt, vilket
kan leda till brand, explosion eller skaderisk.
20. Utsätt inte ett batteripaket eller en apparat för
brand eller höga temperaturer. Exponering för
eld eller temperaturer över 130 °C kan leda till
explosion.
21. Följ alla laddningsinstruktioner och ladda inte
batteripaketet eller apparaten utanför det tem-
peraturintervall som anges i instruktionerna.
Felaktig laddning, eller vid temperaturer utanför
det angivna intervallet, kan skada batteriet och
öka risken för brand.
SPARA DESSA ANVISNINGAR.
YTTERLIGARE
SÄKERHETSANVISNINGAR
Denna maskin är avsedd för att användas i hushåll.
1. Läs denna bruksanvisning och laddarens
bruksanvisning noggrant innan du använder
dammsugaren.
2. Plocka inte upp följande material:
Varmt material som tända cigaretter eller
gnist-/metalldamm som skapas när man
slipar/sågar i metall
Lättantändliga material som bensin, thin-
ner, fotogen eller färg
Explosivt material som nitroglycerin
Antändbart material såsom aluminium,
zink, magnesium, titan, fosfor eller
celluloid
Blöt smuts, vatten, olja eller liknande
Hårda bitar med vassa kanter som träi-
sor, metaller, stenar, glas, spikar, stift
eller rakblad
Pulver som klumpar ihop sig såsom
cement eller toner
20 SVENSKA
Ledande damm som metall eller kol
Fina korn som betongdamm
Att göra detta kan orsaka brand, skada och/
eller skada på egendom.
3. Stanna maskinen omedelbart om du lägger
märke till något onormalt.
4. Om du tappat eller stött till dammsugaren,
kontrollera att den inte har skadats innan du
använder den.
5. Använd inte dammsugaren nära kaminer eller
andra värmekällor.
6. Blockera inte intagshålet eller
ventilationshålen.
SPARA DESSA ANVISNINGAR.
Viktiga säkerhetsanvisningar för
batterikassetten
1. Innan batterikassetten används ska alla
instruktioner och varningsmärken på (1) bat-
teriladdaren, (2) batteriet och (3) produkten
läsas.
2. Montera inte isär eller mixtra med batterikas-
setten. Det kan leda till brand, överdriven värme
eller explosion.
3. Om drifttiden blivit avsevärt kortare ska
användningen avbrytas omedelbart. Det kan
uppstå överhettning, brännskador och t o m en
explosion.
4. Om du får elektrolyt i ögonen ska de sköljas
med rent vatten och läkare uppsökas omedel-
bart. Det nns risk för att synen förloras.
5. Kortslut inte batterikassetten.
(1) Rör inte vid polerna med något strömfö-
rande material.
(2) Undvik att förvara batterikassetten till-
sammans med andra metallobjekt som
t.ex. spikar, mynt o.s.v.
(3) Skydda batteriet mot vatten och regn.
En batterikortslutning kan orsaka ett
stort strömöde, överhettning, brand och
maskinhaveri.
6. Förvara och använd inte verktyget och batteri-
kassetten på platser där temperaturen kan nå
eller överstiga 50 °C.
7. Bränn inte upp batterikassetten även om
den är svårt skadad eller helt utsliten.
Batterikassetten kan explodera i öppen eld.
8.
Spika inte i, krossa, kasta, tappa eller slå batteri-
kassetten mot hårda föremål. Dylika händelser kan
leda till brand, överdriven värme eller explosion.
9. Använd inte ett skadat batteri.
10.
De medföljande litiumjonbatterierna är föremål
för kraven i gällande lagstiftning för farligt gods.
För kommersiella transporter (av t.ex. tredje parter
som speditionsrmor) måste de särskilda transport-
krav som anges på emballaget och etiketter iakttas.
För att förbereda den produkt som ska avsändas
krävs att du konsulterar en expert på riskmaterial.
Var också uppmärksam på att det i ditt land kan
nnas ytterligare föreskrifter att följa.
Tejpa över eller maskera blottade kontakter och
packa batteriet på sådant sätt att det inte kan röra
sig fritt i förpackningen.
11. När batterikassetten ska kasseras måste den
tas bort från maskinen och kasseras på ett
säkert sätt. Följ lokala föreskrifter beträande
avfallshantering av batteriet.
12. Använd endast batterierna med de produkter
som specicerats av Makita. Att använda bat-
terierna med ej godkända produkter kan leda till
brand, överdriven värme, explosion eller utläck-
ande elektrolyt.
13. Om maskinen inte används under en lång tid
måste batteriet tas bort från maskinen.
14. Under och efter användning kan batterikasset-
ten bli het vilket kan orsaka brännskador eller
lättare brännskador. Var uppmärksam på hur
du hanterar varma batterikassetter.
15. Vidrör inte verktygets kontakter direkt efter
användning eftersom de kan bli heta och
orsaka brännskador.
16. Låt inte isor, damm eller smuts fastna i kon-
takterna, i hål eller spår i batterikassetten. Det
kan leda till att verktyget eller batterikassetten
värms upp, fattar eld, går sönder eller inte fung-
erar som de ska, vilket kan orsaka brännskador
eller personskador.
17. Såvida inte verktyget stöder arbeten i närheten
av högspänningsledningar får batterikassetten
inte användas i närheten av en högspännings-
ledning. Det kan leda till att verktyget eller batteri-
kassetten går sönder eller inte fungerar korrekt.
18. Förvara batteriet utom räckhåll för barn.
SPARA DESSA ANVISNINGAR.
FÖRSIKTIGT: Använda endast äkta Makita-
batterier. Användning av oäkta Makita-batterier eller
batterier som har manipulerats kan leda till person-
och utrustningsskador eller till att batteriet fattar eld.
Det upphäver också Makitas garanti för verktyget och
laddaren.
Tips för att uppnå batteriets max-
imala livslängd
1. Ladda batterikassetten innan den är helt
urladdad. Stanna alltid maskinen och ladda
batterikassetten när du märker att maskinen
blir svagare.
2. Ladda aldrig en fulladdad batterikassett.
Överladdning förkortar batteriets livslängd.
3. Ladda batterikassetten vid en rumstemperatur
på 10 °C - 40 °C. Låt en varm batterikassett
svalna innan den laddas.
4. När batterikassetten inte används ska den tas
bort från verktyget eller laddaren.
5. Ladda batterikassetten om du inte har använt
den på länge (mer än sex månader).
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92

Makita CL002G Användarmanual

Typ
Användarmanual