Nederman 160E Series Användarmanual

Instruction manual

Portable Vacuum Unit

160E Series

144171(01)

Original instruction manual

INSTRUCTION MANUAL EN

Translation of original instruction manual

ANVÄNDARMANUAL SV

BEDIENUNGSANLEITUNG DE

BETJENINGSVEJLEDNING DA

BRUKSANVISNING NO

HANDLEIDING NL

INSTRUKCJA UŻYTKOWANIA PL

KÄYTTÖOHJEET FI

MANUAL DE INSTRUCCIONES ES

MANUAL DE INSTRUÇÕES PT

MANUALE D’ISTRUZIONE IT

MANUEL D’INSTRUCTION FR

NÁVOD K OBSLUZE CS

Portable Vacuum Unit 160E Series

2

Portable Vacuum Unit 160E Series

3

Declaration of conformity ................................................................................4

Figures ...................................................................................................................................................... 6

English ...................................................................................................................................................... 9

Svenska ..............................................................................................................................................17

Deutch ..................................................................................................................................................25

Dansk ...................................................................................................................................................... 33

Norsk ........................................................................................................................................................41

Nederlands ................................................................................................................................. 49

Polski....................................................................................................................................................... 57

Suomi ..................................................................................................................................................... 65

Español .............................................................................................................................................. 73

Português ...................................................................................................................................... 81

Italiano .................................................................................................................................................89

Français ............................................................................................................................................. 97

Český .................................................................................................................................................. 105

Portable Vacuum Unit 160E Series

4

Declaration of conformity

We, AB Ph. Nederman & Co., declare under our sole responsibility

that the Nederman product:

Portable Vacuum Unit 160E Series with accessories to which this

declaration relates, are in conformity with the following:

Directives

2004/108/EC, 2006/95/EC, 2006/42/EC.

Standards

EN ISO 12100-1, EN ISO 12100-2.

The manager of development and engineering is responsible for the

technical documentation.

English

EN

Vaatimustenmukaisuusvakuutus

Me, AB Ph. Nederman & Co., vakuutamme yksinomaan omalla

vastuullamme, että Nederman-tuote Portable Vacuum Unit 160E Series

lisävarusteineen, joita tämä vakuutus koskee, täyttää seuraavien

direktiivien ja standardien mukaiset vaatimukset:

Direktiivit

2004/108/EC, 2006/95/EC, 2006/42/EC.

Standardit

EN ISO 12100-1, EN ISO 12100-2.

Kehitys- ja suunnittelu päällikkö on vastuussa teknisistä

asiakirjoista.

Suomi

FI

Konformitätserklärung

Wir, AB Ph. Nederman & Co., erklären in alleiniger Verantwortung,

dass das Nederman Produkt:

Portable Vacuum Unit 160E Series auf welches sich diese Erklärung

bezieht, mit den folgenden Richtlinien übereinstimmt:

Richtlinien

2004/108/EC, 2006/95/EC, 2006/42/EC.

Standards

EN ISO 12100-1, EN ISO 12100-2.

Der Leiter für Entwicklung & Konstruktion ist verantwortlich für

die technische Dokumentation.

Deutch

DE

Samsvarserklæring

Vi, AB Ph. Nederman & Co, erklærer på eget ansvar at Nedermans

produkt:

Portable Vacuum Unit 160E Series med tilbehør som denne

erklæringen gjelder for, er i samsvar med følgende:

Direktiver

2004/108/EC, 2006/95/EC, 2006/42/EC.

Standarder

EN ISO 12100-1, EN ISO 12100-2.

Den tekniske sjefen har ansvaret for den tekniske dokumentasjonen.

Norsk

NO

Conformiteitsverklaring

Wij, AB Ph. Nederman & Co, verklaren in uitsluitende

aansprakelijkheid dat het product van Nederman:

Portable Vacuum Unit 160E Series, met toebehoren waarop deze

verklaring van toepassing is, in overeenstemming zijn met de volgende:

Richtlijnen

2004/108/EC, 2006/95/EC, 2006/42/EC.

Normen

EN ISO 12100-1, EN ISO 12100-2.

De technisch manager is verantwoordelijk voor de technische

documentatie.

Nederlands

NL

Försäkran om överensstämmelse

Vi, AB Ph. Nederman & Co. försäkrar under eget ansvar att

Nederman-produkten:

Portable Vacuum Unit 160E Series med tillbehör som omfattas av

denna försäkran är i överensstämmelse med följande:

Direktiv

2004/108/EC, 2006/95/EC, 2006/42/EC.

Standarder

EN ISO 12100-1, EN ISO 12100-2.

Chefen för utveckling och konstruktion är ansvarig för den tekniska

dokumentationen.

Svenska

SV

Overensstemmelseserklæring

Vi, AB Ph. Nederman & Co. erklærer som eneansvarlige, at

produkterne fra Nederman:

Portable Vacuum Unit 160E Series med tilbehør, som denne

erklæring relaterer til, er i overensstemmelse med det følgende:

Direktiver

2004/108/EC, 2006/95/EC, 2006/42/EC.

Standarder

EN ISO 12100-1, EN ISO 12100-2.

Chefen af udvikling og konstruktion er ansvarlig for den tekniske

dokumentation.

Dansk

DA

Deklaracja zgodności

My, AB Ph. Nederman & Co., niniejszym oświadczamy na naszą własną

odpowiedzialność, że produkty: Portable Vacuum Unit 160E Series

rmy Nederman wraz z akcesoriami, których dotyczy niniejsza

deklaracja są zgodne z następującymi przepisami:

Dyrektywy

2004/108/EC, 2006/95/EC, 2006/42/EC.

Normy

EN ISO 12100-1, EN ISO 12100-2.

Kierownik działu rozwoju I inżynierii, odpowiedzialny za

dokumentację techniczną.

Polski

PL

AB Ph. Nederman & Co.

P.O. Box 602

SE-251 06 Helsingborg

Sweden Lena Åberg

Manager, Development & Engineering

Portable Vacuum Unit 160E Series

5

Declaração de conformidade

Nós, AB Ph. Nederman & Co., declaramos sob nossa inteira

responsabilidade que o produto Nederman:

Portable Vacuum Unit 160E Series, com os acessórios aos quais esta

declaração se refere, está em conformidade com o seguinte:

Directivas

2004/108/EC, 2006/95/EC, 2006/42/EC.

Normas

EN ISO 12100-1, EN ISO 12100-2.

O gestor de desenvolvimento e engenharia é responsável pela

documentação técnica.

Português

PT

Déclaration de conformité

Nous, AB Ph. Nederman & Co., déclarons sous notre seule

responsabilité, que les produits Nederman :

Portable Vacuum Unit 160E Series avec les accessoires auxquels fait

référence la présente déclaration, sont en conformité avec les :

Directives

2004/108/EC, 2006/95/EC, 2006/42/EC.

Normes

EN ISO 12100-1, EN ISO 12100-2.

Le directeur du service Recherche & Développement est

responsable de la documentation technique.

Français

FR

Declaración de Conformidad

Nosotros, AB Ph. Nederman & Co., declaramos bajo nuestra única

responsabilidad que el producto Nederman:

Portable Vacuum Unit 160E Series, con los accesorios a los que se

reere esta declaración, está en conformidad con el texto siguiente:

Directivas

2004/108/EC, 2006/95/EC, 2006/42/EC.

Normas

EN ISO 12100-1, EN ISO 12100-2.

El director técnico es responsable de la documentación técnica.

Español

ES

Dichiarazione di conformità

Noi, AB Ph. Nederman & Co., dichiariamo sotto la nostra esclusiva

responsabilità che il prodotto Nederman:

Portable Vacuum Unit 160E Series, con gli accessori cui la presente

dichiarazione è relativa, è conforme a:

Direttive

2004/108/EC, 2006/95/EC, 2006/42/EC.

Norme

EN ISO 12100-1, EN ISO 12100-2.

Il Responsabile per lo sviluppo e la progettazione é responsabile

della documentazione tecnica.

Italiano

IT

Prohlášení o shodě

My, společnost AB Ph. Společnost Nederman & Co. prohlašuje na

svou zodpovědnost, že výrobek Nederman:

Portable Vacuum Unit 160E Series s příslušenstvím, ke kterým se

vztahuje prohlášení, jsou v souladu s následujícími:

Směrnicemi

2004/108/EC, 2006/95/EC, 2006/42/EC.

Normy

EN ISO 12100-1, EN ISO 12100-2.

Za technickou dokumentaci odpovídá projektový & technický

manažer.

Český

CS

Portable Vacuum Unit 160E Series

6

Figures

1 2

a b

c

3

56

d

b - c

a

4

Portable Vacuum Unit 160E Series

7

7 8

a

4 x

9

11

13

12

10

Portable Vacuum Unit 160E Series

8

XXxxxxxx XXXX

IP24

Type:

160E

Power:

Voltage:

XXXXW XXXXW max

XXXV XXHz

Ser.No Art.No Ctr.No

Made in Sweden year

Helsingborg Sweden

14

160E Series

9

EN

English

Instruction manual

Portable Vacuum Unit

160E Series

1 Preface......................................................................................................................................................10

2 Notices ...................................................................................................................................................... 10

3 Safety .........................................................................................................................................................11

4 Description ...........................................................................................................................................11

4.1 Function .........................................................................................................................................11

5 Main components .........................................................................................................................12

5.1 Power unit .....................................................................................................................................12

5.1.1 Maintenance ..........................................................................................................................12

5.2 Filter/Filter package ...............................................................................................................12

5.3 Micro-lter (optional) ............................................................................................................. 12

5.3.1 Installation/replacement ....................................................................................................12

5.3.2 Filter package ........................................................................................................................ 12

5.4 Casing .............................................................................................................................................13

5.5 Plastic sack/Filter bag .......................................................................................................... 13

5.6 Receptacle ................................................................................................................................... 13

5.7 Frame...............................................................................................................................................13

5.7.1 Maintenance ..........................................................................................................................13

5.8 Pressure drop indication ....................................................................................................13

5.9 Wheel ..............................................................................................................................................13

6 Using 160E Series .......................................................................................................................14

6.1 Connecting and starting .....................................................................................................14

6.2 Cleaning equipment ..............................................................................................................14

6.3 Start/Stop ...................................................................................................................................... 14

7 Transport and lifting ....................................................................................................................14

8 Maintenance ....................................................................................................................................... 15

8.1 Cleaning .........................................................................................................................................15

8.2 Spare parts ..................................................................................................................................15

9 Recycling ................................................................................................................................................15

Figures ......................................................................................................................................................... 6

Table of contents

160E SeriesEN

10

1 Preface

This manual is for the correct installation, use and maintenance of this product.

Read it carefully before using this product or carrying out maintenance.

Replace the manual immediately if lost.

This product has been designed to meet the requirements of relevant EC

directives. To maintain this status, all installation, repair and maintenance

work for this product is to be carried out by qualied personnel using only

original spare parts. Contact the nearest authorized distributor or Nederman

for advice on technical service and obtaining spare parts. Also read

Chapter ‘3 Safety’ thoroughly.

Nederman continuously improves its products’ design and efciency through

modications, and reserves the right to do so without introducing these

improvements to previously supplied products. Nederman also reserve the right

to, without previous notice, modify data and equipment as well as operating

and maintenance instructions.

2 Notices

This document contains important information that is presented either as a

warning, caution or note. See the following examples:

WARNING! Type of injury.

Warnings indicate a potential hazard to the health and safety of personnel, and

how that hazard may be avoided.

CAUTION! Type of risk.

Cautions indicate a potential hazard to the product but not to personnel, and

how that hazard may be avoided.

NOTE! Notes contain other information that is important for personnel.

160E Series

11

EN

3 Safety

WARNING!

• The 160E with 1 phase motor may only be connected to a grounded power

socket of the same voltage as stated on the machine data plate.

• A damaged component should immediately be replaced with a new genuine

spare part. Electrical components may only be replaced by a person with

the necessary expertise.

• The appliance must be disconnected from the power (remove the plug

from the power socket) before carrying out any form of intervention, e.g.

dismantling the motor assembly or replacing a micro-lter.

• Take care not to spread dust when changing the plastic sack and when

replacing the micro-lter. Wear an approved breathing mask in the case of

hazardous dust.

• For reasons of safety, do not put the vacuum hose inlet near the eyes, ears or

other part of the body.

• The 160E is not classied as a wet vacuum cleaner. Large amounts of water

may not be sucked into the unit. However, it may be used for damp material

and in a damp environment.

• Hot or red-hot material, ammable uids, explosive or health-impairing

fumes as well as dust that could cause a dust explosion must not be sucked

into the 160E. Neither must the appliance be used in environments where

such material exists.

• Do not operate the 160E with a 1 phase motor when the vacuum is almost

or fully restricted. Little or no airow results in overheating of the motor.

4 Description

4.1 Function

Electrical driven, 1-phase with separately cooled motors. The appliance can be

provided with manual and automatic start/stop modes depending on the model.

With automatic start/stop, the appliance is controlled by a connected electric

tool.

The rated power, voltage, safety class, ow, working pressure, max pressure,

etc. are stated on the machine data plate. The noise level during normal

operation is 75 dB(A) according to ISO 11201.

Dust separation takes place in three stages:

• Stage 1 is a collecting receptacle into which larger particles fall.

• Stage 2 is a ne lter.

• Stage 3 is a micro-lter (optional) with a degree of separation > 99.997%

(DOP).

Coarse particles are separated directly into the collecting receptacle’s plastic

sack.

If the appliance is supplied with a closed lter bag instead of a plastic sack,

most of the dust will be deposited there. Fine dust follows the upward moving

ow of air and is deposited on the outside of the lters. The appliance has

a manual function for cleaning the ne lters. The principle of the cleaning

function is that the control is switched on, creating a pressure shock to dislodge

160E SeriesEN

12

dust from the lters. The dust falls down and is collected in the plastic sack of

the receptacle.

Very small particles can pass through the lter package and on to the micro-

lter (optional). This has a very high degree of separation, > 99.997% (DOP).

The cleaned air moves on to the high-pressure fan in the motor assembly.

The air leaves the appliance via noise-abating ducts in the motor assembly. If

ow-through is too small over a sufciently long period, e.g. due to a closed

ap valve or blocked hose, the motors will become overheated. The suction

hose should therefore not be completely blocked for longer than a few seconds.

Clogged lters, which also reduce the ow of air, can result in overheating.

The appliance should not be used as a stationary vacuum appliance because of

the danger of overheating.

5 Main components

5.1 Power unit

See Figure 1. The motor assembly includes fan motor, connection cable and

starting equipment. Some models are equipped with automatic electric starters.

5.1.1 Maintenance

Replace the fan motors in the motor assembly if they are not working

satisfactorily. The motors’ carbon brushes are worn out after about 700 hours

of operation. Replacing the motor’s carbon brushes more than once is not

recommended. The motor collector becomes worn and new brushes will wear

very quickly. Replace the entire motor instead. The motor is accessible after

unscrewing the motor assembly.

5.2 Filter/Filter package

CAUTION!

The appliance should never be operated with a lter bag only, but should

always be equipped with another lter. Check regularly that the lter is not

defective.

5.3 Micro-lter (optional)

5.3.1 Installation/replacement

See Figures 2–3. Change the micro-lter once a year or more often if

vacuum performance decreases despite cleaning the ne lters. Installation/

replacement of micro-lter, see Figure 3. Use genuine micro-lters only.

Ensure that the rubber gasket on the lter seals tightly against the bottom of

the motor assembly. Leakage between micro-lter and fan inlet must not occur.

Use an approved breathing mask when changing the lters.

5.3.2 Filter package

See Figure 4.

Filter package, Cartridge (4a)

The particles collect on the outside of the lter. Cleaning of the lter is

carried out hourly or when the vacuum performance decreases. If required the

cartridge lter should be changed.

160E Series

13

EN

Filter package, PP (4b)

The particles collect on the outside of the lter. Cleaning is carried out every

other hour or when the vacuum performance decreases. Replacing the entire

lter package is recommended. When only changing the socks, the lter ring

should also be replaced.

Filter package, anti-static (4c)

The lter socks have been treated with anti-static agent and have smooth

surfaces. This means there is reduced risk of sparks and dust explosion,

and ensures better cleaning. The particles collect on the outside of the lter.

Cleaning is carried out every other hour or when the vacuum performance

decreases. Replacing the entire lter package is recommended. When only

changing the socks, the lter ring should also be replaced.

Filter package, sack (4d)

The sack should be replaced if it becomes worn, damaged or when particles

begin to penetrate.

5.4 Casing

The casing forms a container for the lter package. It is important that the

eccentric catches are secured with locking cotters, see Figure 5.

5.5 Plastic sack/Filter bag

See Figure 6. The appliance can be supplied with either a plastic sack (6a)

or a lter bag (6b) for collecting dust. Replacing is carried out in accordance

with 6c.

5.6 Receptacle

See Figure 7. All applications are supplied with receptacles. The receptacle has

a ap valve for connecting the suction hose. The ap valve closes automatically

to prevent the spread of dust when the hose is disconnected.

5.7 Frame

5.7.1 Maintenance

See Figure 8. Check the screw mountings, broken parts should be replaced.

5.8 Pressure drop indication

A high pressure drop across the lters is indicated by a lamp being lit, Figure 9

item a. The lamp is lit if the lters need to be cleaned or replaced. The lamp is

also lit when the appliance is running with the ap valve closed.

5.9 Wheel

See Figure 10. Depending on the model, the appliance can be equipped with

plastic wheels, pneumatic rubber wheels or rubber wheels ø 200 mm.

160E SeriesEN

14

6 Using 160E Series

The 160E is suitable for most types of dust in industrial applications and on

building sites. There are important exceptions, see Chapter ‘3 Safety’. Oil mist

can clog the lters.

In normal operation, without any electric tool connected, the appliance is

started in mode I. If an electric tool is connected to the 160E, the switch is

normally set in mode II.

In mode II, the appliance starts when the connected tool is started and stops

with a slight delay when the tool is stopped. See Chapter ‘6.3 Start/Stop’ for

further information.

6.1 Connecting and starting

The appliance may only be connected to a grounded power socket with

the voltage as stated on the machine data plate, see Figure 14. Information

about maximum power consumption is also given. Note that the total power

consumption may increase in certain cases of operation with electric tools

connected.

6.2 Cleaning equipment

• The CE370 is used for heavy duty cleaning.

• The CE370 is used for normal cleaning and industrial cleaning.

• The CE370C is equipped with an anti-static suction hose for avoiding

static electricity.

6.3 Start/Stop

Electric tools can be connected to an appliance equipped with electric Start/

Stop. This does not apply to 110–120 V appliance versions. Minimum power

consumption of connected tools for auto-start is 60 W. Maximum permitted

power is stated on the decal located near the power point.

The connection of tools at a higher power could result in electric overload.

7 Transport and lifting

The 160E can be transported vertically or horizontally, see Figure 12. To avoid

spreading any hazardous dust during transportation, the vacuum hose should

be disconnected from the inlet so that the ap valve closes.

The hose can be “short-circuited” by connecting the couplings at either end of

the hose. The collecting receptacle must be tted when transporting and lifting

the appliance. The eccentric catches holding the collecting receptacle must be

secured by locking cotters, see Figure 5.

Remove the cleaning equipment and other loose parts from the appliance

before lifting. Replace sack/bag in the collecting receptacle if it contains large

amounts of heavy material (>10 kg). The appliance weighs 19 kg when empty.

Attach lifting straps to the frame handle to lift the appliance, see Figure 13.

WARNING! Risk of personal injury.

It is prohibited to remain underneath the 160E when lifting. Lifting the 160E

by the handle located on top of the motor assembly is prohibited.

160E Series

15

EN

8 Maintenance

Read Chapter ‘3 Safety’ before carrying out maintenance.

Installation, repair and maintenance work is to be carried out by qualied

personnel using only original Nederman spare parts. Contact your nearest

authorized distributor or Nederman for advice on technical service.

NOTE! The service intervals in this chapter are based on the unit being

professionally maintained.

8.1 Cleaning

See Figure 11. The ne lters should be cleaned daily or as soon as it is felt that

the vacuum performance has decreased. Cleaning is carried out as follows:

Switch off the appliance and switch on the cleaning control about 4 times. The

control is situated on the side of the appliance, see Figure 11. If the appliance is

supplied with a closed lter bag in the collecting receptacle, there will be less

need for cleaning the ne lters. When changing from a plastic sack to a lter

bag, the ne lter must rst be thoroughly cleaned.

8.2 Spare parts

Contact your nearest authorized distributor or Nederman for advice

on technical service or if you require help with spare parts. See also

www.nederman.com.

Ordering spare parts

When ordering spare parts always state the following:

• Part number and control number (see the product identication plate).

• Detail number and name of the spare part (see www.nederman.com).

• Quantity of the parts required.

9 Recycling

The product has been designed for component materials to be recycled.

Its different material types must be handled according to relevant local

regulations. Contact the distributor or Nederman if uncertainties arise when

scrapping the product at the end of its service life.

Most 160E components (94% of the total weight) can be recycled when

scrapping the appliance. Most of the plastic parts are labelled to facilitate

sorting. Components that at present cannot be easily recycled are wheels made

of composite material, certain parts of the top of the motor and dirty lters.

In order to meet ofcial requirements, American variants of the 160E with

1-phase motor contain ameproofed components in the motor assembly and

these contain small amounts of bromine. Bromine is classied as hazardous to

health and must be dealt with according to local directions when scrapping.

160E SeriesEN

16

160E Series

17

SV

Svenska

Användarmanual

Portable Vacuum Unit

160E Series

1 Förord ........................................................................................................................................................18

2 Riskmeddelanden ........................................................................................................................18

3 Säkerhet ..................................................................................................................................................19

4 Beskrivning ..........................................................................................................................................19

4.1 Funktion .........................................................................................................................................19

5 Huvudkomponenter ....................................................................................................................20

5.1 Drivkälla .........................................................................................................................................20

5.1.1 Underhåll ................................................................................................................................20

5.2 Filter/Filterpaket .......................................................................................................................20

5.3 Mikrolter (option) ................................................................................................................... 20

5.3.1 Montering/byte ......................................................................................................................20

5.3.2 Filterpaket ...............................................................................................................................20

5.4 Mantel ..............................................................................................................................................21

5.5 Plastsäck/Filterpåse .............................................................................................................. 21

5.6 Kärl ....................................................................................................................................................21

5.7 Stativ ................................................................................................................................................21

5.7.1 Underhåll ................................................................................................................................21

5.8 Tryckfallsindikering ................................................................................................................. 21

5.9 Hjul ....................................................................................................................................................21

6 Använda 160E Series ............................................................................................................... 22

6.1 Anslutning och start ............................................................................................................... 22

6.2 Städutrustning ...........................................................................................................................22

6.3 Start/Stopp ...................................................................................................................................22

7 Transport och lyft ...........................................................................................................................22

8 Underhåll ................................................................................................................................................23

8.1 Rensning .......................................................................................................................................23

8.2 Reservdelar .................................................................................................................................23

9 Återvinning ...........................................................................................................................................23

Figurer .......................................................................................................................................................... 6

Innehållsförteckning

160E SeriesSV

18

1 Förord

Den här manualen är en genomgång av korrekt installation, användning och

underhåll av produkten. Läs igenom den noggrant innan du använder eller

utför underhåll på produkten. Ersätt omedelbart manualen om den skulle

försvinna.

Den här produkten är utformad för att uppfylla kraven i relevanta EU-direktiv.

För att bibehålla denna status måste alla installationer, reparationer och allt

underhåll av produkten utföras av behörig personal som endast använder

originaldelar. Kontakta närmaste auktoriserade återförsäljare eller Nederman

för rådgivning vid teknisk service samt för att erhålla reservdelar.

OBS! Läs igenom kapitel ‘3 Säkerhet’.

Nederman förbättrar löpande produkternas design och effektivitet genom

produktutveckling. Vi förbehåller oss rätten att göra så utan att tillhandahålla

dessa förbättringar på tidigare levererade produkter. Vi förbehåller oss också

rätten att utan föregående avisering ändra såväl data och utrustning som drifts-

och underhållsinstruktioner.

2 Riskmeddelanden

Det här dokumentet innehåller viktig information som presenteras antingen

som en varning, ett försiktighetsmeddelande eller en kommentar. Se följande

exempel:

VARNING! Typ av skada.

Varning anger en möjlig risk för personalens hälsa och säkerhet samt hur den

risken kan undvikas.

FÖRSIKTIGT! Typ av risk.

Försiktighetsmeddelanden anger en möjlig risk för produkten men inte

personalen samt hur den risken kan undvikas.

OBS! Kommentarer innehåller övrig information som användaren bör vara

särskilt uppmärksam på.

160E Series

19

SV

3 Säkerhet

VARNING!

•160E med 1-fas motor får endast anslutas till jordat vägguttag med samma

spänning som anges på maskinskylten.

•Skadad komponent ska omedelbart bytas ut mot ny originaldel. Byte av

elektrisk komponent får endast utföras av person som har nödvändig

kännedom.

•Aggregatet ska göras strömlöst (drag ur stickproppen från vägguttag) innan

någon form av ingrepp görs, ex demontering av motorpaket eller byte av

mikrolter.

•Iakttagförsiktighetvidbyteavplastsäckochvidbyteavmikroltersåatt

damm inte sprids. Vid hälsofarligt damm, använd godkänt andningsskydd.

•För inte sugslangens mynning intill ögon, öron eller andra kroppsdelar på

grund av skaderisk.

•160E är inte klassad som våtdammsugare. Stora mängder vatten får inte

sugas in i apparaten. Däremot får den användas för fuktigt material och i

fuktig miljö.

•Hett eller glödande material, brandfarliga vätskor, explosiva eller

hälsovådliga gaser samt damm som kan förorsaka dammexplosion får ej

sugas in i 160E. Ej heller får apparaten användas i utrymmen där sådana

ämnen förekommer.

•Körinte160Emed1-fasmotornästanellerheltstrypt.Litetellerobentligt

luftödemedförattmotornbliröverhettad.

4 Beskrivning

4.1 Funktion

160Eärenindustridammsugaresomnnsmedentypavkraftaggregat.

El-drift, 1-fas med separatkylda motorer. Aggregatet kan ha manuell och

automatisk start/stopp-funktion beroende på modell. Vid automatisk start/stopp

styrs aggregatet av anslutet elverktyg.

Anslutningseffekt,spänning,skyddsform,öde,arbetstryck,max-tryckm.m.

anges på maskinskylten. Ljudnivån vid normal användning är 75 dB(A) enligt

ISO 11201.

Dammavskiljning sker i tre steg:

•Steg 1 är ett uppsamlingskärl, där större partiklar faller ner.

•Steg2ärettnlter.

•Steg3ärettmikrolter(option)medavskiljningsgraden>99,997%

(DOP).

Grova partiklar avskiljs direkt i uppsamlingskärlets plastsäck.

Äraggregatetförseddmedslutenlterpåseiställetförplastsäckkommeräven

merparten av dammet att samlas där.

Fint damm följer med den uppåtgående luftströmmen och sätter sig på utsidan

avltren.Aggregatetharenmanuellfunktionförrensningavnltren.

Principen för rensningen innebär att man slår på reglaget vilket skapar en

tryckstötsomskakarlossdammfrånltren.Dammetfallernerochsamlasi

uppsamlingskärlets plastsäck.

160E SeriesSV

20

Mycketsmåpartiklarkanpasseraigenomlterpaketetochvidaretill

mikroltret(option).Dettaharmyckethögavskiljningsgrad,>99,997%(DOP).

Denrenadeluftengårvidaretillhögtrycksäktenimotorpaketet.Luften

lämnar aggregatet via motorpaketets ljuddämpande kanaler.

Om genomströmningen är för liten under tillräckligt lång tid, till exempel på

grund av stängd klaffventil eller blockerad slang, blir motorerna överhettade.

Sugslangen bör därför inte blockeras helt mer än några få sekunder. Igensatta

lter,vilketocksåminskarluftödet,kanmedföraöverhettning.Aggregatet

ska inte användas som stationärt sugaggregat, då det kan medföra risk för

överhettning.

5 Huvudkomponenter

5.1 Drivkälla

Segur1.Imotorpaketetingåräktmotor,anslutningskabelsamt

startutrustning. Vissa modeller är utrustade med elektrisk startautomatik.

5.1.1 Underhåll

Bytäktmotorimotorpaketetomdefungerarotillfredsställande.Motorernas

kol är utslitna efter ca 700 drifttimmar. Byte av motorns kol mer än en gång

rekommenderas inte. Bl. a motorns kollektor slits och nya kol kommer att slitas

ut snabbt. Byt i stället hela motorn. Motorn är åtkomlig sedan motorpaketet

skruvats isär.

5.2 Filter/Filterpaket

FÖRSIKTIGT!

Aggregatetböraldrigkörasmedenbartlterpåseutanböralltidvaraförsett

medytterligarelter.Kontrolleramedjämnamellanrumattltretärhelt.

5.3 Mikrolter (option)

5.3.1 Montering/byte

Segur2–3.Bytmikrolter1gångperårelleroftareomsugförmågan

minskartrotsrensningavnltren.Montering/byteavmikroltersegur3.

Användendastoriginalmikrolter.Setillattltretsgummipackningslutertätt

motmotorpaketetsundersida.Läckagemellanmikrolterochäktinloppfår

inteförekomma.Användgodkäntandningsskyddvidlterbyte.

5.3.2 Filterpaket

Segur4.

Filterpaket, Patron (4a)

Partiklarnasamlaspåutsidanavltret.Rengöringavltretgörsvarjetimme

ellernärsugförmåganavtar.Vidbehovbytspatronlter.

Sidan laddas ...

Nederman 160E Series Användarmanual

Nederman 160E Series Användarmanual

på andra språk

Relaterade papper

Andra dokument