Yamaha DPX-1100 Bruksanvisning

Kategori
Dataprojektorer
Typ
Bruksanvisning
YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.
YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA
YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, F.R. OF GERMANY
YAMAHA ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE
YAMAHA ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD18 7GQ, ENGLAND
YAMAHA SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN
YAMAHA MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA
Printed in Japan
WC71040
C2004 All Rights Reserved.
10_DPX-1000-Cover1-4_E.p65 2004.03.15, 12:411
Explanation of Graphical Symbols
The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended to alert
you to the presence of uninsulated “dangerous
voltage” within the product’s enclosure that may
be of sufficient magnitude to constitute a risk of
electric shock to persons.
The exclamation point within an equilateral
triangle is intended to alert you to the presence of
important operating and maintenance (servicing)
instructions in the literature accompanying the
appliance.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,
DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.
1 Read these instructions.
2 Keep these instructions.
3 Heed all warnings.
4 Follow all instructions.
5 Do not use this apparatus near water.
6 Clean only with dry cloth.
7 Do not block any ventilation openings. Install in accordance
with the manufacturer’s instructions.
8 Do not install near any heat sources such as radiators, heat
registers, stoves, or other apparatus (including amplifiers) that
produce heat.
9 Do not defeat the safety purpose of the polarized or grounding-
type plug. A polarized plug has two blades with one wider than
the other. A grounding type plug has two blades and a third
grounding prong. The wide blade or the third prong are
provided for your safety. If the provided plug does not fit into
your outlet, consult an electrician for replacement of the
obsolete outlet.
10 Protect the power cord from being walked on or pinched
particularly at plugs, convenience receptacles, and the point
where they exit from the apparatus.
11 Only use attachments/accessories specified by the
manufacturer.
12 Use only with the cart, stand, tripod, bracket,
or table specified by the manufacturer, or sold
with the apparatus. When a cart is used, use
caution when moving the cart/apparatus
combination to avoid injury from tip-over.
13 Unplug this apparatus during lightning storms
or when unused for long periods of time.
14 Refer all servicing to qualified service personnel. Servicing is
required when the apparatus has been damaged in any way,
such as power-supply cord or plug is damaged, liquid has been
spilled or objects have fallen into the apparatus, the apparatus
has been exposed to rain or moisture, does not operate
normally, or has been dropped.
15 Be sure to allow spaces of at least 30cm above, behind and on
both sides the unit.
16 Do not place the following objects on this unit:
A vessel with water in it. If the vessel falls by vibrations and
water spills, it may cause damage to the unit, and/or you may
get an electric shock.
IMPORTANT!
Please record the serial number of this unit in the space below.
Model:
Serial No.:
The serial number is located on the bottom of the unit.
Retain this Owner’s Manual in a safe place for future reference.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
IMPORTANT SAFETY INSTRUCTIONS
i
OBSERVERA
Apparaten kopplas inte bort från växelströmskällan (nätet) så länge som
den är ansluten till vägguttaget, även om själva apparaten har stängts av.
ADVARSEL
Netspæendingen til dette apparat er IKKE afbrudt, sålæenge
netledningen siddr i en stikkontakt, som er t endt – også selvom der or
slukket på apparatets afbryder.
VAROITUS
Laitteen toisiopiiriin kytketty käyttökytkin ei irroita koko laitetta
verkosta.
Alleen voor klanten in Nederland
Bij dit product zijn batterijen geleverd.
Wanneer deze leeg zijn, moet u ze niet
weggooien maar inleveren als KCA.
10_DPX-1000-Cover2-3_E.p65 2004.03.15, 12:181
FCC INFORMATION (for US customers only)
1. IMPORTANT NOTICE: DO NOT MODIFY THIS
UNIT!
This product, when installed as indicated in the instructions
contained in this manual, meets FCC requirements.
Modifications not expressly approved by Yamaha may void
your authority, granted by the FCC, to use the product.
2. IMPORTANT: When connecting this product to accessories
and/or another product use only high quality shielded
cables. Cable/s supplied with this product MUST be used.
Follow all installation instructions. Failure to follow
instructions could void your FCC authorization to use this
product in the USA.
3. NOTE: This product has been tested and found to comply
with the requirements listed in FCC Regulations, Part 15 for
Class “B” digital devices. Compliance with these
requirements provides a reasonable level of assurance that
your use of this product in a residential environment will not
result in harmful interference with other electronic devices.
This equipment generates/uses radio frequencies and, if not
installed and used according to the instructions found in the
users manual, may cause interference harmful to the operation
of other electronic devices.
Compliance with FCC regulations does not guarantee that
interference will not occur in all installations. If this product is
found to be the source of interference, which can be determined
by turning the unit “OFF” and “ON”, please try to eliminate the
problem by using one of the following measures:
Relocate either this product or the device that is being affected
by the interference.
Utilize power outlets that are on different branch (circuit
breaker or fuse) circuits or install AC line filter/s.
In the case of radio or TV interference, relocate/reorient the
antenna. If the antenna lead-in is 300 ohm ribbon lead, change
the lead-in to coaxial type cable.
If these corrective measures do not produce satisfactory results,
please contact the local retailer authorized to distribute this type
of product. If you can not locate the appropriate retailer, please
contact Yamaha Electronics Corp., U.S.A. 6660 Orangethorpe
Ave, Buena Park, CA 90620.
The above statements apply ONLY to those products distributed
by Yamaha Corporation of America or its subsidiaries.
We Want You Listening For A Lifetime
YAMAHA and the Electronic Industries Association’s Consumer Electronics Group want you to get the most out of your
equipment by playing it at a safe level. One that lets the sound come through loud and clear without annoying blaring or
distortion – and, most importantly, without affecting your sensitive hearing. Since hearing damage from loud sounds is often
undetectable until it is too late, YAMAHA and the Electronic Industries Association’s Consumer Electronics Group recommend
you to avoid prolonged exposure from excessive volume levels.
COMPLIANCE INFORMATION STATEMENT
(DECLARATION OF CONFORMITY PROCEDURE)
Responsible Party: Yamaha Electronics Corporation
Address: 6660 Orangethorpe Avenue
Buena Park, CA90620
Telephone: 714-522-9105
Fax: 714-670-0108
Type of Equipment: Projector
Model Name: DPX-1100
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following conditions:
1) this device may not cause harmful interference, and
2) this device must accept any interference received including interference that may cause undesired operation.
See the user manual instructions if interference to radio reception is suspected.
ii
10_DPX-1100-ULCaut_E.p65 2004.03.15, 11:021
Caution: Read this before operating this unit.
To assure the finest performance, please read this manual
carefully. Keep it in a safe place for future reference.
Installation
Install this unit in a well-ventilated, cool, dry, clean place with
at least 30 cm (1 feet) clearance on the top, right and left, and
at the back of this unit — away from direct sunlight, heat
sources, vibration, dust, moisture, and/or cold.
Locate this unit away from other electrical appliances, motors,
or transformers to avoid humming sounds. To prevent fire or
electrical shock, do not place this unit where it may get
exposed to rain, water, and/or any type of liquid.
Do not expose this unit to sudden temperature changes from
cold to hot, and do not locate this unit in an environment with
high humidity (i.e. a room with a humidifier) to prevent
condensation inside this unit, which may cause an electrical
shock, fire, damage to this unit, and/or personal injury.
On the top of this unit, do not place:
Other components, as they may cause damage and/or
discoloration on the surface of this unit.
Burning objects (i.e. candles), as they may cause fire,
damage to this unit, and/or personal injury.
Containers with liquid in them, as they may cause electrical
shock to the user and/or damage to this unit.
Do not cover this unit with a newspaper, tablecloth, curtain, etc.
in order not to restrict heat dissipation. If the temperature inside
this unit rises too much, it may cause fire, damage to this unit,
and/or personal injury.
When installing this unit on the ceiling, make sure the ceiling
has sufficient strength to support this unit and the ceiling
mounts for an extended period of time. Installation must be
performed only by qualified service personnel.
Operation
Remove the lens cover before starting any operation of this unit
to prevent the heat from staying around the lens. Operation
with the cap on may cause damage to this unit.
Do not plug in this unit to a wall outlet until all connections are
complete.
Only the voltage specified on this unit must be used. Using this
unit with a higher voltage than specified is dangerous and may
cause fire, damage to this unit, and/or personal injury.
YAMAHA will not be held responsible for any damage
resulting from use of this unit with a voltage other than that
specified.
Do not use force on switches, knobs and/or cords.
Take care of this unit so that no foreign objects and/or liquid
drop inside this unit.
To prevent damage by lightning, disconnect the power cord
from the wall outlet during an electrical storm.
Do not look into the lens while this unit is turned on. It may
cause serious damage to your eyesight.
Before moving this unit, press STANDBY/ON to set this unit
in the standby mode, and disconnect the AC power plug from
the wall outlet.
Do not attempt to modify or fix this unit. Contact qualified
YAMAHA service personnel when any service is needed. The
cabinet should never be opened for any reason.
When not planning to use this unit for a long period of time
(i.e. vacation), disconnect the AC power plug from the wall
outlet.
When disconnecting the power cord from the wall outlet, grasp
the plug; do not pull the cord.
Be sure to read the “TROUBLESHOOTING” section on
common operating errors before concluding that this unit is
faulty.
Others
Clean the lens carefully so as not to create any scratches by
using a blower or lens paper.
Replace the lamp when the LAMP warning indicator blinks in
red after the lamp usage has exceeded 2000 hours. Follow the
lamp replacement procedure described in this manual.
For U.K. customers
IMPORTANT
THE WIRES IN THIS MAINS LEAD ARE COLOURED IN
ACCORDANCE WITH THE FOLLOWING CODE:
GREEN-AND-YELLOW: EARTH
BLUE: NEUTRAL
BROWN: LIVE
As the colours of the wires in the mains lead of this apparatus may
not correspond with the coloured markings identifying the
terminals in your plug, proceed as follows:
The wire which is coloured GREEN-AND-YELLOW must be
connected to the terminal in the plug which is marked by the letter
E or by the safety earth symbol or coloured GREEN or GREEN-
and-YELLOW.
The wire which is coloured BLUE must be connected to the
terminal which is marked with the letter N or coloured BLACK.
The wire which is coloured BROWN must be connected to the
terminal which is marked with the letter L or coloured RED.
If the socket outlets in the home are not suitable for the plug
supplied with this appliance, it should be cut off and an appropriate
3 pin plug fitted. For details, refer to the instructions described
below.
Note
The plug severed from the mains lead must be destroyed, as a plug with
bared flexible cord is hazardous if engaged in a live socket outlet.
For Canadian customers
To prevent electric shock, match wide blade of plug to
wide slot and fully insert.
This Class B digital apparatus complies with Canadian ICES-
003.
iii
10_DPX-1100-ULCaut_E.p65 2004.03.15, 11:022
1
Table of contents
1 Getting started 2
Inappropriate places for installation........ 2
Accessory check .................................... 2
2 Features 3
3 Controls and functions 4
4 Remote control 6
5
Before using the DPX-1100 for projection
10
6 Projection 12
Checking installation and connections...
12
Turning the projector power on / off ..... 13
Selecting an input signal ...................... 15
Adjusting the vertical position and focus of an image .....
20
7 Menu 22
Menu configurations............................. 22
Menu items .......................................... 23
Menu operations .................................. 32
8 Memory function
(Saving, recalling, locking and resetting memory.) 41
9 Connection 46
Connecting to image source components ...
46
Connecting to computer devices .......... 47
10
Setting up the projector and screen
48
Setting up the projector ........................ 48
Projection distance and the screen ...... 49
Projection image position ..................... 50
11
Reference 51
Glossary ............................................... 51
Signals the DPX-1100 can project ....... 53
Maintenance ......................................... 54
Troubleshooting .................................... 56
Message display................................... 58
LED Indicator meanings ....................... 59
Specifications ....................................... 60
Dimensional drawing ............................ 61
Getting started
Features
Controls and functions
Remote control
Before using the
DPX-1100 for projection
Projection
Menu
Memory function
Connection
Setting up the
projector and screen
Reference
2
3
4
5
6
7
8
9
10
11
1
11_DPX-1100_E.p65 2004.03.15, 11:031
2
Inappropriate places for installation
If this unit is not correctly installed in an appropriate place, it may cause fire or failure, or damage the unit itself. Carefully choose the place
to install this unit by avoiding the places listed below.
1. Places where the temperature and humidity vary greatly
Do not install this unit in a place where the temperature and humidity become extremely high or the temperature becomes extremely
low.
This unit must be used within a temperature range of 535°C.
2. Places without adequate ventilation
Install this unit with at least 30 cm (1 feet) of ventilation space on the top, right and left, and back.
Do not cover the ventilation slots of this unit. Covering the slots will obstruct heat dissipation.
Install this unit on the firm surface.
Do not cover this unit with a tablecloth, etc.
Make sure there is nothing to get sucked into the ventilation slots so that the temperature of this unit does not become too high.
If you are going to install the unit in a rack, be sure to leave space for ventilation to prevent exhaust overheating the unit.
3. Places where it gets dusty
If the filter is blocked with dust, the temperature of this unit may become too high.
4. Places with too much vibration or impact
Vibration and impact can damage parts of this unit.
5. Places where this unit gets exposed to water or high humidity
If this unit is exposed to water or high humidity, it may cause a fire or electrical shock.
6. Unstable places
If this unit is installed on an unstable or an inclined tabletop, it may fall and cause damage to the unit or personal injury.
7. In close proximity to a Radio or Stereo
The unit may interfere with reception if placed in close proximity to a radio or television receiver.
Warning
To ensure vivid, high contrast images, make sure that no light other than the projector light falls directly on the screen.
Accessory check
Please check that all accessories listed here are included in your package.
Remote control Batteries (AA, UM-3 or R6) Power cable
Pin/BNC adapters Lens cap
45
RESET
6
123
VIDEO
STILL
HIDE
PATTIRIS
AUTO
SETTING
ZOOM FOCUSV. POS
LIGHT
BD4
S VIDEO
A
INPUT
MEMORY
HDMI
INPUT
MENU
ASPECT
ESCAPE
1 Getting started
Trigger-out DC plug
(For USA only)
11_DPX-1100_E.p65 2004.03.15, 11:032
3
Features
2
Adjust 7 colors independently (including white), or use the
automatic color balance function
Adjustment is not restricted to simple color temperature control. The DPX-1100 also allows
you to adjust the 7-axis WRGBYCM color coordinate and gain parameters directly. For better
consistency, you can also control color temperature and RBG balance together, allowing you to
check that the changes you make are always consistent with your preferences.
The latest digital I/F provides sharp, detailed images
The DPX-1100 is equipped with an HDMI terminal, which is set to become the standard for the
coming generation of products. Connect it to a DVD player or set-top box with a HDMI
terminal to receive digital image data directly, and enjoy completely digitally processed images.
Compatible with the content protection function of HDCP.
Intelligent memory functions
The DPX-1100 can store six image memory settings for each terminal. For each memory
setting, you can set parameters for different input resolutions, and the unit will automatically
switch to the parameters you set when it begins displaying an image of an appropriate
resolution. For example, the unit automatically changes display settings without changing
memory numbers when you change from watching a DVD to watching a HDTV image for
which you have set different image menu item parameters.
In-line menus for image adjustment
You can access image adjustment menu items at the touch of a button, and adjust images while
viewing them without opening the menu screen.
Highly configurable electronic adjustment gives you the
freedom to place the projector wherever you want
A short focal length, high power zoom, and fully vertically adjustable lens allow you to use the
projector in a wide range of environments. You can also use the remote control to access many
lens functions such as focus, zoom, and lens shift to fine-tune the projector from your viewing
position.
Uses the latest DMD
TM
device HD2+
The projector uses the latest upgraded version of the high contrast 720p DMD
TM
HD2 panel,
the HD2+, to reduce black levels even further and reproduce contrasts close to that of a film.
2 Features
11_DPX-1100_E.p65 2004.03.15, 11:033
4
Main unit <Front panel and controls>
STANDBY
/
ON
SETTING
LAMP COVER TEMP FAN
PATTERN
ESCAPE
MENU
INPUT
DIGITAL CINEMA PROJECTOR DPX-1100
ASPECT
1
2
3
4
5
1
6
7
8
9
0
STANDBY
/
ON
SETTING
LAMP COVER TEMP FAN
PATTERN
ESCAPE
MENU
INPUT
ASPECT
A
E
B
CD
2 STANDBY/ON button
Switches the unit between Standby and On (operational)
modes.
3 ESCAPE button
Exits from submenus.
4 PATTERN button
Switches the built-in test pattern on and off.
5 ASPECT button
Turns the display aspect menu for the project image on and off
6 (Enter) button
Sets values when the DPX-1100 is displaying the menu. When
the menu is not displayed, the DPX-1100 displays the in-line
image quality adjustment menu. ( page 40)
1 LED Indicators
The main unit is equipped with 5 indicators to display various states of operation. See page 59 for explanations of the LED indicator
meanings.
7 MENU button
Switches the settings and adjustments menu display on and off.
8 SETTING button
Selects lens adjustment modes.
9 INPUT button
Switches the input signal selection menu display on and off.
0 Cursor buttons
Use the h, g, +, - buttons for system operations, menu item
selection, and changing system values.
A STANDBY/ON indicator
(There is also an LED on the front panel of the main unit)
B LAMP warning indicator
C COVER warning indicator
D TEMP warning indicator
E FAN warning indicator
Lamp cover
Ventilation inlet
Adjuster
Makes small adjustments to
the projection angle
Lens
Lens cap
Exhaust vent
Front remote control sensor
STANDBY/ON indicator
3 Controls and functions
11_DPX-1100_E.p65 2004.03.15, 11:034
5
Controls and functions
3
HDMI
G/Y B/PB/CB R/PR/CR
INPUT A
HD/SYNC
VD
OUT IN
REMOTE
TRIGGER OUT
S VIDEO VIDEO
INPUT B
RGB/YP
BPR/YCBCR
RS-232C
D4 VIDEO
q
8
765432109
wer
Main unit <Rear panel / Connections>
1 INPUT B (D-sub 15 pin)
Receives component video and RGB (RGB/YPBPR/YCBCR)
signals. Use a D-sub monitor cable to connect components to
this jack.
2 D4 VIDEO (D jack)
Receives signals output from the D jacks of other AV
components. It is compatible with D1 - D4 formats.
3 - 7 INPUT A (BNC jacks)
Receive component video and RGB signals. Connect
component signal connectors from AV components to input
jacks 3 - 5, and RGB signal connectors from computers to
input jacks 3 - 7. Use BNC cables for these connections.
3 G/Y (G, or luminance signal)
4 B/P
B/CB (B, or color difference signal)
5 R/P
R/CR (R, or color difference signal)
6 HD/SYNC (Horizontal sync signal, composite sync signal)
7 VD (Vertical sync signal)
8 S VIDEO (Mini DIN jack)
Receives signals from S-VIDEO output jacks of other AV
components. Use an S-VIDEO cable for these connections.
9 VIDEO (Pin Jack)
Receives composite video signals from the VIDEO output
jacks of other AV components. Use a video pin cable for these
connections.
0 AC inlet
Insert the supplied AC power cord here.
q HDMI
TM
(HDMI
TM
jack)
Receives HDMI
TM
signals from computers or AV components.
w REMOTE IN / OUT jack
Connect the remote control to the REMOTE IN jack if you
want to use it through a cable. The REMOTE OUT jack
outputs the signal received through the REMOTE IN jack
without any change.
e RS-232C (D-sub 9 pin)
For use in servicing this unit.
r TRIGGER OUT
Outputs control signals to external components. This output
provides a potential of 12 V/ maximum 200 mA when this unit
is projecting.
Rear remote control sensor
11_DPX-1100_E.p65 2004.03.15, 11:035
6
45
RESET
6
123
VIDEO
STILL
HIDE
PATTIRIS
AUTO
SETTING
ZOOM FOCUSV. POS
LIGHT
BD4
S VIDEO
A
INPUT
MEMORY
HDMI
INPUT
MENU
ASPECT
ESCAPE
o
i
u
y
t
p
r
e
1
2
3
4
5
6
7
8
9
0
q
w
Remote control functions
Buttons on the remote control with identical names to those on the main unit perform identical functions. When using the remote control,
point it at the sensor on the front or back of the main unit from a distance of 7m (23 feet) or less.
1 Transmit indicator
Lights up when the remote control sends infrared signals to the
main unit.
2 AUTO button
Automatically sets the DPX-1100 to the best settings for the
type of signal it is currently receiving.
3 V.POS button
Switches on or off the vertical adjustment mode for the entire
image.
4 ZOOM button
Switches on or off the size adjustment mode for the image the
DPX-1100 is projecting.
5 IRIS button
Switches on or off the lens iris change mode.
6 ESCAPE button
Exits from submenus.
7 Cursor buttons
Use the h ,g, +, - buttons to move the cursor within the on-
screen display.
8 ASPECT button
Turns the display aspect menu for the project image on and off
9 RESET button
Resets all adjustable parameters to their default settings.
0 STILL button
Stops a moving image, displaying a still of the image the DPX-
1100 is projecting. Press STILL again to cancel this effect.
q INPUT area
Selects the INPUT jacks directly.
w MEMORY area
Calls stored memory (all parameter settings) directly.
e button
Switches the unit between Standby and On (operational)
modes.
r FOCUS button
Switches on or off the focus adjustment mode for the image the
DPX-1100 is projecting.
t PATT (PATTERN) button
Switches on and off the built-in test pattern.
y MENU button
Switches on and off the settings and adjustments menu display.
u (Enter) button
Sets values when the DPX-1100 is displaying the menu. When
the menu is not displayed, the DPX-1100 displays the in-line
image quality adjustment menu. ( page 40)
4 Remote control
11_DPX-1100_E.p65 2004.03.15, 11:036
7
Remote control
4
i INPUT button
Switches on and off the input signal selection menu display.
o LIGHT switch
Moving this switch up or down lights the high-use 2, 6, 8,
e, y, and i buttons. The light disappears if you do not
perform any operation within 10 seconds.
p HIDE button
Temporarily halts projection of the image the DPX-1100 is
currently displaying. Press again to cancel this effect.
a Remote control code switch
The remote control functions when the code set in the menu is
the same as that set on the remote control. The default menu
setting is ID-1.
s Remote control cable jack
Connect a cable to this jack to link the remote control to the
main unit.
IR
IS
V
.PO
S
A
U
T
O
PA
T
T
FOCUS
Z
O
O
M
S
E
T
T
I
N
G
ID-2
ID
-1
R
E
S
E
T
HIDE
S
TILL
S VIDEO
V
ID
E
O
B
A
D
4
4
5
6
1
2
3
HD
M
I
MEMORY
INPUT
L
IG
H
T
INPUT
MENU
ES
C
A
PE
ASPECT
a
s
11_DPX-1100_E.p65 2004.03.15, 11:037
8
Loading the batteries into the remote control
1. Remove the battery compartment cover.
2. Insert two batteries (AA, UM3, or R6 type), matching the polarity
markings on the batteries with those in the battery
compartment.
3. After loading the batteries, close the cover until it snaps into
place.
Warning
If the remote control must be used closer to the main unit than normal, or does not always operate correctly, exchange the
batteries for new ones.
Do not mix old and new, or different types of batteries.
Remove the batteries if you do not plan to use the unit for a long time.
If the batteries leak, dispose of them immediately, taking care not to touch the battery fluid. If the battery fluid comes into contact
with your eyes, mouth, or skin, rinse it off with water immediately and consult a doctor. Clean the battery compartment thoroughly
before installing new batteries.
Using the remote control with a wired connection
Use a 2P monaural miniplug cable to connect the remote control jack on the underside of the remote control to the REMOTE IN jack on the
main unit.
I
R
IS
V
.
P
O
S
A
U
T
O
P
A
T
T
FOCUS
Z
O
O
M
S
E
T
T
I
N
G
ID-2
ID-1
R
E
S
E
T
H
I
D
E
S
T
I
L
L
S
V
I
D
E
O
V
ID
E
O
B
A
D4
4
5
6
1
2
3
HDMI
M
EM
O
RY
INP
UT
L
IG
H
T
IN
P
U
T
M
E
N
U
E
S
C
A
P
E
A
S
P
E
C
T
HDMI
G/Y B/PB/CB R/PR/CR
INPUT A
HD/SYNC
VD
OUT IN
REMOTE
TRIGGER OUT
S-VIDEO VIDEO
INPUT B
RGB/YP
BPR/YCBCR
RS-232C
D4 VIDEO
1
3
2
11_DPX-1100_E.p65 2004.03.15, 11:038
9
Remote control
4
Distance to sensor Angle to sensor
7m 30˚ vertically and horizontally
(approximate value) (approximate value)
Limits for using the remote control
Use the remote control within the following parameters. The remote control may not function correctly if you use it outside the limits
detailed here.
Warning
Bright or fluorescent light on the main unit remote sensor may inhibit the functioning of the remote control
Objects placed between the main unit remote sensor and the remote control may block the remote control signal and inhibit
functioning.
A left/right arc of 30 degrees A vertical arc of 30 degrees
HDMI
G/Y B/P
B
/C
B
R/P
R
/C
R
INPUT A
HD/SYNC
VD
OUT IN
REMOTE
TRIGGER OUT
S-VIDEO VIDEO
INPUT B
RGB/YP
B
P
R
/YC
B
C
R
RS-232C
D4 VIDEO
45
RESET
6
123
VIDEO
STILL
HIDE
PATTIRIS
AUTO
SETTING
ZOOM FOCUSV. POS
LIGHT
BD4
S VIDEO
A
INPUT
MEMORY
HDMI
INPUT
MENU
ASPECT
ESCAPE
45
RESET
6
123
VIDEO
STILL
HIDE
PATTIRIS
AUTO
SETTING
ZOOM FOCUSV. POS
LIGHT
BD4
S VIDEO
A
INPUT
MEMORY
HDMI
INPUT
MENU
ASPECT
ESCAPE
11_DPX-1100_E.p65 2004.03.15, 11:039
10
Before using the DPX-1100 (referred to as the main unit below) for projection, install the main unit and a screen, connect the main unit to an
AV component or computer, and adjust the projection image. You can begin projection as soon as installation is complete.
Refer to the sections below for information on how to install the main unit to suit your viewing environment.
You have not installed the main unit or screen
Immediately after purchase, when you have not installed either the main unit or a screen.
When moving the main unit and screen to a new location.
You have installed the main unit and screen, and connected an
image playback component
You have installed the main unit and screen, and connected image playback source components.
You are using the main unit in a previously installed location with previously connected source components.
You have installed the main unit and screen, but not connected
any image playback components
You have installed the main unit and screen, but not connected any image playback source components.
You are using the main unit in a previously installed location, and wish to change the component you use as an image playback source.
You do not need to carry out step 3 or step 4 if you
do not want to adjust the projection image. If the
unit does not project the image correctly, it may not
be connected correctly. In this case, carry out this
procedure starting from step 2.
STEP3
Select an image and
project
page 12 - 21
The image is used
for adjusting the
image position
and focus
STEP4
Adjust the
projection image
page 22 - 40
Use the menu to
adjust projection
details.
Projection
preparations
complete
STEP2
Connect AV
components or a
computer to the
main unit
page 46
STEP3
Select an image and
project
page 12 - 21
The image is used
for adjusting the
image position
and focus
STEP4
Adjust the
projection image
page 22 - 40
Use the menu to
adjust projection
details.
Projection
preparations
complete
STEP 1
Install the main unit
and screen
page 48
STEP3
Select an image and
project
page 12 - 21
The image is used
for adjusting the
image position
and focus
STEP2
Connect AV
components or a
computer to the
main unit
page 46
Projection
preparations
complete
5
Before using the DPX-1100 for projection
STEP4
Adjust the
projection image
page 22 - 40
Use the menu to
adjust projection
details.
11_DPX-1100_E.p65 2004.03.15, 11:0310
11
Before using the DPX-1100 for projection
5
Step2
Connect an AV component or a computer
Connect AV components
Connect a computer page 46
Step3
Turning the projector power on and
selecting an image for projection
Turn on the projector power
Begin playback of the input image
Select an input signal
Select a project image aspect
Adjust the image
Focus/Vertical and Horizontal position/Size/Iris
page 12 - 21
Step1
Setting up the projector and screen
Install the projector
Install the screen page 48
Only adjust these
parameters when
necessary. It is not
necessary to adjust these
settings once you have set
them initially.
Step4
Using the menu to adjust the image quality and
other parameters
Adjusting image quality: Set image quality details
Signal setting: Set input signal details
Default settings: Set the default settings for everyday use
Installation settings: Set to suit your viewing environment page 22 - 40
11_DPX-1100_E.p65 2004.03.15, 11:3611
12
Checking installation and connections
Pre-operation check
Prior to projection, adjust settings to suit the location of the main unit and screen, and the input signal you are using.
However, there is usually no need to adjust any settings if you have not changed the installation location or components since the last time
you used this unit. Check settings and connections only when the unit does not appear to project images correctly.
PHONO
DVR
STANDBY
/ON
PURE DIRECT
2CH/MULTI CH
SPEAKERS
VIDEO AUX
REC OUT/ZONE 2
INPUT MODE
SOURCE/REMOTE
DVDDTV/LD
MD/TAPE
CD-R
TUNER
CD
VIDEO AUX
VCR 2
VCR 1
SAT
CABLE
A B
STRAIGHT
EFFECT
MULTI CH
INPUT
DSP
PROGRAM
BALANCE
TONE
CONTROL
VOLUME
INPUT SELECTOR
MULTI JOG
SILENT OPTIMIZER
MIC
PHONES
OPTICAL
R
AUDIO
L
VIDEO
S VIDEO
Is the main unit power
turned on?
Main unit
Are the components connected correctly?
Connecting to image source components
page 46
Image source component
Is the image source component
power turned on?
For an explanation of detailed settings, see Menu. page 22 - 40
Check installation and connections
Select an image for projection and image adjustment
Projection preparations complete
Turn on the projector power
Begin playback of the source image for adjustment
Select a projection image
(Select an input signal and projection image aspect)
Adjust focus and vertical/ horizontal positioning,
6 Projection
Prior to projection, check that the main unit and screen and correctly installed, and that image source components are connected correctly.
To project images, carry out the following procedure
Is the screen installed correctly?
Setting up the projector and screen
page 48
12_DPX-1100_E.p65 2004.03.15, 11:0412
Projection
13
6
Turning the power on
Always remove the lens cap before operating the main unit.
Turning the projector power on / off
1. Insert the supplied power cord
firmly into the AC inlet at the rear
of the main unit, then insert the
plug into an AC outlet.
The STANDBY/ON indicator lights orange.
2. Press the STANDBY/ON button
(the
button on the remote
control).
The indicator blinks green and the lamp
lights up in preparation for projection. After
approximately 35 seconds, the indicator
changes from blinking to solid green,
indicating that the unit is ready to project.
Warning
Do not remove the power cord while the STANDBY/ON indicator is blinking green or
lit steady green. This could damage the lamp or reduce lamp life.
HDMI
G/Y B/P
B
/C
B
R/P
R
/C
R
INPUT A
HD/SYNC
VD
OUT IN
REMOTE
TRIGGER OUT
S-VIDEO VIDEO
INPUT B
RGB/YP
B
P
R
/YC
B
C
R
RS-232C
D4 VIDEO
STANDBY
/
ON
SETTING
LAMP COVER TEMP FAN
PATTERN
ESCAPE
MENU
INPUT
ASPECT
STANDBY/ON
indicator
AC inlet
INPUT
MENU
PATTIRIS
AUTO
SETTING
ASPECT
ZOOM FOCUSV. POS
ESCAPE
STANDBY
/
ON
SETTING
LAMP COVER TEMP FAN
PATTERN
ESCAPE
MENU
INPUT
ASPECT
Remote Control Main unit
button STANDBY/ON button
12_DPX-1100_E.p65 2004.03.15, 11:0413
14
1. Press the STANDBY/ON button.
A confirmation message appears on the
screen.
Turning power off
3. If you do not plan to use the main
unit for a long period of time,
attach the lens cap and remove
the plug from the AC outlet.
Warning
Condensation may appear on the unit if the temperature of the surrounding
environment changes quickly. Condensation may also cause the projected image to
be cloudy. Switch off the unit power until the condensation disappears. Switching the
unit on when condensation is present may damage the unit.
2. When you wish to turn off the
main unit power, press the
STANDBY/ON button again.
The lamp changes to a half lit state, and the
fan activates for 2 minutes to cool the lamp.
During this time, the STANDBY/ON
indicator blinks orange, and pressing
STANDBY/ON does not turn main unit
power on again. When the unit finishes
cooling, the fan stops, and the STANDBY/
ON indicator turns orange.
Memo
The lamp may blink when half lit. This is not a defect.
Warning
Do not remove the power cord while the STANDBY/ON indicator is blinking green or
when the fan is activated. This could damage the lamp or reduce lamp life.
Turning the projector power on / off
AC inlet
Press again to enter standby.
HDMI
G/Y B/P
B
/C
B
R/P
R
/C
R
INPUT A
HD/SYNC
VD
OUT IN
REMOTE
TRIGGER OUT
S-VIDEO VIDEO
INPUT B
RGB/YP
B
P
R
/YC
B
C
R
RS-232C
D4 VIDEO
INPUT
MENU
PATTIRIS
AUTO
SETTING
ASPECT
ZOOM FOCUSV. POS
ESCAPE
STANDBY
/
ON
SETTING
LAMP COVER TEMP FAN
PATTERN
ESCAPE
MENU
INPUT
ASPECT
Remote Control Main unit
button STANDBY/ON button
12_DPX-1100_E.p65 2004.03.15, 11:0414
Projection
15
6
<Select using the INPUT button>
Press the INPUT button to select an input signal from an image source component. Choose from the following:
Projection image signal
Selecting an input signal
Selects component video signals received from AV components connected to the VIDEO jack.
Selects S-Video signals received from AV components connected to the S VIDEO jack.
Component : Selects component signals received from the INPUT A BNC jacks.
RGB PC : Selects RGB signals received from computers connected to the INPUT A BNC jacks.
RGB TV : Selects RGB signals received from AV components connected to the INPUT A BNC jacks.
Component : Selects component signals received from the INPUT B D-sub 15 pin jack.
RGB PC : Selects RGB signals received from computers connected to the INPUT B D-sub 15 pin jack.
RGB TV : Selects RGB signals received from AV components connected to the INPUT B D-sub 15 pin jack.
Auto : Signals input to the HDMI jack from AV components (automatically distinguishes between
component and RGB signals).
Component : Selects digital component signals received from AV components connected to the HDMI jack.
RGB TV : Selects digital RGB signals received from AV components connected to the HDMI jack.
Selects component signals received from AV components connected to the D4 VIDEO jack.
INPUT SIGNAL
VIDEO
S VIDEO
INPUT A
INPUT B
HDMI
D4 VIDEO
12_DPX-1100_E.p65 2004.03.15, 11:0415
16
<Using the INPUT button to select a signal>
Selecting an input signal
1. Press the INPUT button.
The input signal selection menu appears on
the display.
4. Select an appropriate setting
from [Component], [RGB PC], or
[RGB TV] and press the
button
to confirm the setting.
3. Press the + button to open the
submenu.
2. Use the h, g cursor buttons to
select an input signal, then press
the
button.
The
mark to the right of the input signal
name indicates that there is a submenu
available for selection.
Input signal
VIDEO
S VIDEO
INPUT A
INPUT B
HDMI
D4
Input signal
VIDEO
S VIDEO
INPUT A
INPUT B
HDMI
D4
Input signal
VIDEO
S VIDEO
INPUT A
INPUT B
HDMI
D4
Component
RGB PC
RGB TV
Input signal
VIDEO
S VIDEO
INPUT A
INPUT B
HDMI
D4
Warning
You can select [Component], [RGB PC], or [RGB TV] for INPUT A and INPUT B, or
[Auto], [Component], or [RGB TV] for HDMI, from the submenu. If you do not select a
setting, the unit continues to use the setting from the last signal it received. To
change this setting, carry out the following procedure.
Memo
If you set your laptop or notebook computer to display simultaneously on its built-in
display and on an external monitor, the main unit may not project the image
incorrectly. If this occurs, set your computer to display on the external monitor only.
Refer to your computers operating instructions for further details.
STANDBY
/
ON
SETTING
LAMP COVER TEMP FAN
PATTERN
ESCAPE MENU
INPUT
ASPECT
45
RESET
6
123
VIDEO
STILL
HDMI
PATTIRIS
AUTO
SETTING
ZOOM FOCUSV. POS
LIGHT
BD4
S VIDEO
A
INPUT
MEMORY
DVI
INPUT
MENU
ASPECT
ESCAPE
+ button
Remote cotrol Main unit
button
INPUT button
Cursor button
12_DPX-1100_E.p65 2004.03.15, 11:0416
1 / 1