Yamaha LPX-500 Användarmanual

OWNER'S MANUAL

LPX-500

Home Cinema Projector

an (English)

403256900

U C A G B R T

I

IMPORTANT SAFETY INSTRUCTIONS

•

••

•

Explanation of Graphical Symbols

1

Read these instructions.

2

Keep these instructions.

3

Heed all warnings.

4

Follow all instructions.

5

Do not use this apparatus near water.

6

Clean only with dry cloth.

7

Do not block any ventilation openings. Install in

accordance with the manufacturer’s instructions.

8

Do not install near any heat sources such as radiators,

heat registers, stoves, or other apparatus (including

amplifiers) that produce heat.

9

Do not defeat the safety purpose of the polarized or

grounding-type plug. A polarized plug has two blades

with one wider than the other. A grounding type plug

has two blades and a third grounding prong. The wide

blade or the third prong are provided for your safety.

If the provided plug does not fit into your outlet,

consult an electrician for replacement of the obsolete

outlet.

10

Protect the power cord from being walked on or

pinched particularly at plugs, convenience

receptacles, and the point where they exit from the

apparatus.

11

Only use attachments/accessories specified by the

manufacturer.

12

Use only with the cart, stand, tripod,

bracket, or table specified by the

manufacturer, or sold with the

apparatus. When a cart is used, use

caution when moving the cart/

apparatus combination to avoid injury

from tip-over.

13

Unplug this apparatus during lightning storms or

when unused for long periods of time.

14

Refer all servicing to qualified service personnel.

Servicing is required when the apparatus has been

damaged in any way, such as power-supply cord or

plug is damaged, liquid has been spilled or objects

have fallen into the apparatus, the apparatus has been

exposed to rain or moisture, does not operate

normally, or has been dropped.

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE

COVER (OR BACK). NO USER-SERVICEABLE

PARTS INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead

symbol, within an equilateral triangle, is

intended to alert you to the presence of

uninsulated “dangerous voltage” within

the product’s enclosure that may be of

sufficient magnitude to constitute a risk

of electric shock to persons.

The exclamation point within an

equilateral triangle is intended to alert

you to the presence of important

operating and maintenance (servicing)

instructions in the literature

accompanying the appliance.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC

SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN

OR MOISTURE.

IMPORTANT!

Please record the serial number of this unit in the space

below.

Model:

Serial No.:

The serial number is located on the bottom of the unit.

Retain this Owner’s Manual in a safe place for future

reference.

CAUTION

RISK OF ELECTRIC

SHOCK DO NOT

OPEN

II

COMPLIANCE INFORMATION STATEMENT

(DECLARATION OF CONFORMITY PROCEDURE)

Responsible Party: Yamaha Electronics Corporation

Address: 6660 Orangethorpe Avenue

Buena Park, CA90620

Telephone: 714-522-9105

Fax: 714-670-0108

Type of Equipment: Projector

Model Name: LPX-500

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following conditions:

1) this device may not cause harmful interference, and

2) this device must accept any interference received including interference that may cause undesired

operation.

See the user manual instructions if interference to radio reception is suspected.

We Want You Listening For A Lifetime

YAMAHA and the Electronic Industries Association’s Consumer Electronics Group want you to get the most

out of your equipment by playing it at a safe level. One that lets the sound come through loud and clear

without annoying blaring or distortion

—

and, most importantly, without affecting your sensitive hearing.

Since hearing damage from loud sounds is often undetectable until it is too late, YAMAHA and the Electronic

Industries Association’s Consumer Electronics Group recommend you to avoid prolonged exposure from

excessive volume levels.

FCC INFORMATION (for US customers)

1. IMPORTANT NOTICE: DO NOT MODIFY THIS

UNIT!

This product, when installed as indicated in the

instructions contained in this manual, meets FCC

requirements. Modifications not expressly

approved by Yamaha may void your authority,

granted by the FCC, to use the product.

2. IMPORTANT:

When connecting this product to

accessories and/or another product use only high

quality shielded cables. Cable/s supplied with this

product MUST be used. Follow all installation

instructions. Failure to follow instructions could

void your FCC authorization to use this product in

the USA.

3. NOTE:

This product has been tested and found to

comply with the requirements listed in FCC

Regulations, Part 15 for Class “B” digital devices.

Compliance with these requirements provides a

reasonable level of assurance that your use of this

product in a residential environment will not result

in harmful interference with other electronic

devices.

This equipment generates/uses radio frequencies and,

if not installed and used according to the instructions

found in the users manual, may cause interference

harmful to the operation of other electronic devices.

Compliance with FCC regulations does not guarantee

that interference will not occur in all installations. If

this product is found to be the source of interference,

which can be determined by turning the unit “OFF”

and “ON”, please try to eliminate the problem by using

one of the following measures:

Relocate either this product or the device that is being

affected by the interference.

Utilize power outlets that are on different branch

(circuit breaker or fuse) circuits or install AC line

filter/s.

In the case of radio or TV interference, relocate/

reorient the antenna. If the antenna lead-in is 300 ohm

ribbon lead, change the lead-in to coaxial type cable.

If these corrective measures do not produce

satisfactory results, please contact the local retailer

authorized to distribute this type of product. If you can

not locate the appropriate retailer, please contact

Yamaha Electronics Corp., U.S.A. 6660 Orangethorpe

Ave, Buena Park, CA 90620.

The above statements apply ONLY to those products

distributed by Yamaha Corporation of America or its

subsidiaries.

III

Caution: Read this before operating this unit.

•

••

•

To assure the finest performance, please read this

manual carefully. Keep it in a safe place for future

reference.

Installation

•

••

•

Install this unit in a well-ventilated, cool, dry, clean

place with at least 10 cm clearance on the top, right and

left, and at the back of this unit — away from direct

sunlight, heat sources, vibration, dust, moisture, and/or

cold.

•

••

•

Locate this unit away from other electrical appliances,

motors, or transformers to avoid humming sounds. To

prevent fire or electrical shock, do not place this unit

where it may get exposed to rain, water, and/or any type

of liquid.

•

••

•

Do not expose this unit to sudden temperature changes

from cold to hot, and do not locate this unit in an

environment with high humidity (i.e. a room with a

humidifier) to prevent condensation inside this unit,

which may cause an electrical shock, fire, damage to this

unit, and/or personal injury.

•

••

•

On the top of this unit, do not place:

—Other components, as they may cause damage and/or

discoloration on the surface of this unit.

—Burning objects (i.e. candles), as they may cause fire,

damage to this unit, and/or personal injury.

—Containers with liquid in them, as they may cause

electrical shock to the user and/or damage to this unit.

•

••

•

Do not cover this unit with a newspaper, tablecloth,

curtain, etc. in order not to restrict heat dissipation. If the

temperature inside this unit rises too much, it may cause

fire, damage to this unit, and/or personal injury.

•

••

•

When installing this unit on the ceiling, make sure the

ceiling has sufficient strength to support this unit and the

ceiling mounts for an extended period of time.

Installation must be performed only by qualified service

personnel.

Operation

•

••

•

Remove the lens cap before starting any operation of this

unit to prevent the heat from staying around the lens.

Operation with the cap on may cause damage to this

unit.

•

••

•

Do not plug in this unit to a wall outlet until all

connections are complete.

•

••

•

Only the voltage specified on this unit must be used.

Using this unit with a higher voltage than specified is

dangerous and may cause fire, damage to this unit, and/

or personal injury. YAMAHA will not be held

responsible for any damage resulting from use of this

unit with a voltage other than that specified.

•

••

•

Do not use force on switches, knobs and/or cords.

•

••

•

Take care of this unit so that no foreign objects and/or

liquid drop inside this unit.

•

••

•

To prevent damage by lightning, disconnect the power

cord from the wall outlet during an electrical storm.

•

••

•

Do not look into the lens while this unit is turned on. It

may cause serious damage to your eyesight.

•

••

•

Before moving this unit, press

STANDBY/ON

to set

this unit in the standby mode, and disconnect the AC

power plug from the wall outlet.

•

••

•

Do not attempt to modify or fix this unit. Contact

qualified YAMAHA service personnel when any service

is needed. The cabinet should never be opened for any

reason.

•

••

•

When not planning to use this unit for a long period of

time (i.e. vacation), disconnect the AC power plug from

the wall outlet.

•

••

•

When disconnecting the power cord from the wall outlet,

grasp the plug; do not pull the cord.

•

••

•

Be sure to read the “TROUBLESHOOTING” section on

common operating errors before concluding that this unit

is faulty.

Others

•

••

•

Clean the lens carefully so as not to create any scratches

by using a blower or lens paper.

•

••

•

Replace the lamp when the LAMP/COVER indicator

flashes in red after the lamp usage has exceeded 1000

hours. Follow the lamp replacement procedure described

in this manual.

For U.K. customers

•

••

•

If the socket outlets in the home are not suitable for the

plug supplied with this appliance, it should be cut off

and an appropriate 3 pin plug fitted. For details, refer to

the instructions described below.

Note

•

••

•

The plug severed from the mains lead must be destroyed, as

a plug with bared flexible cord is hazardous if engaged in a

live socket outlet.

This unit is not disconnected from the AC power source

as long as it is connected to the wall outlet, even if this

unit itself is turned off. This state is called the standby

mode. In this state, this unit is designed to consume a

very small quantity of power.

IMPORTANT

THE WIRES IN THIS MAINS LEAD ARE

COLOURED IN ACCORDANCE WITH THE

FOLLOWING CODE:

GREEN-AND-YELLOW: EARTH

BLUE: NEUTRAL

BROWN: LIVE

As the colours of the wires in the mains lead of this

apparatus may not correspond with the coloured markings

identifying the terminals in your plug, proceed as follows:

The wire which is coloured GREEN-AND-YELLOW must

be connected to the terminal in the plug which is marked by

the letter E or by the safety earth symbol or coloured

GREEN or GREEN-and-YELLOW.

The wire which is coloured BLUE must be connected to the

terminal which is marked with the letter N or coloured

BLACK.

The wire which is coloured BROWN must be connected to

the terminal which is marked with the letter L or coloured

RED.

For Canadian Customers

To prevent electric shock, match wide blade of plug to

wide slot and fully insert.

This Class B digital apparatus complies with Canadian

ICES-003.

Indications

Notations used in this Owner’s Manual

Indicates procedures where personal injury or damage to the projector may occur if the

procedures are not followed correctly.

Indicates additional information and points which may be useful to know regarding a topic.

Indicates that an explanation of the underlined word or words in front of this symbol appears

in the glossary of terms.

Refer to the “Glossary” in the “Appendix”. (p.61)

Indicates operating methods and the order of operations.

The procedure indicated should be carried out in the order of the numbers.

Procedure

1

Contents

Notes on Handling and Storage ........................................................................2

Accessories .......................................................................................................3

Features of the Projector ...................................................................................4

Basic Operations

Turning On the Projector ...................................................................................6

Connecting the Power Cord .....................................................................................6

Turning On the Power and Projecting Images .........................................................7

Turning Off the Projector ...................................................................................9

Adjusting the Screen Image ............................................................................11

Adjusting the Image Size .......................................................................................11

Adjusting the Image Angle ....................................................................................11

Correcting Keystone Distortion .............................................................................12

Displaying a Test Pattern .......................................................................................13

Adjusting the Image Quality.............................................................................14

Focusing the Screen Image ....................................................................................14

Selecting the picture mode .....................................................................................14

Selecting the Image Aspect Ratio .......................................................................... 15

Automatic Adjustment of Computer Images .........................................................17

Advanced Operations

Functions for Enhancing Projection.................................................................20

Using the Menus.....................................................................................................20

Description of Functions ........................................................................................23

Saving and Retrieving Image Quality Settings (Memory Save)............................ 24

Using the Menu Functions...............................................................................26

Image Menu............................................................................................................26

Signal Menu ...........................................................................................................30

Setup Menu ............................................................................................................31

Info Menu............................................................................................................... 33

Troubleshooting

When Having Some Trouble ...........................................................................36

When the Indicators Provide No Help .............................................................38

Appendices

Maintenance ....................................................................................................46

Cleaning .................................................................................................................46

Replacing Consumables .........................................................................................47

Optional Accessories.......................................................................................51

List of Supported Signal Resolutions...............................................................52

Component Video Input.........................................................................................52

Composite Video/S-Video Input............................................................................52

RGB Input ..............................................................................................................53

Specifications ..................................................................................................54

Appearance .....................................................................................................56

Part Names and Functions ..............................................................................57

Front/Top................................................................................................................57

Control Panel..........................................................................................................58

Rear ........................................................................................................................ 59

Base ........................................................................................................................59

Remote Control ......................................................................................................60

Glossary ..........................................................................................................61

Index................................................................................................................63

Basic Operations

Advanced Operations

TroubleshootingAppendices

2

Notes on Handling and Storage

Be sure to observe the following precautions to avoid malfunctions, operating errors or damage to the projector.

Notes on Handling and Storage

• Do not set up the projector near high-voltage electrical wires or sources of magnetic fields.

These may interfere with correct operation.

• Do not touch the lens with bare hands.

If fingerprints or grease get onto the lens, it can interfere with the quality of the projected images. Attach the lens

cover to the lens when the projector is not in use.

• During projection, some points (dots) may appear lit at all times, or they may be dark at all times.

This is caused by the characteristics of the LCD panel, and is not a sign of a malfunction. The LCD panel is

manufactured using extremely high-precision technology. However, black dots may appear on the panel, or some

red, blue or green dots may light extremely brightly at times. Furthermore, sometimes stripe-shaped color

irregularities or brightness irregularities may also appear.

• Remove the batteries from the remote control before storage.

If the batteries are left in the remote control for long periods, they may leak.

• Always attach the lens cap to the lens when not using the projector, to prevent the lens from becoming dirty or

damaged.

• The mercury lamp that is used as the projector's light source deteriorates as a result of normal use and as a

result of impacts or other damage, and may also break with a loud noise, stop working or reach the end of its

service life more quickly.

At such times, the amount of time remaining before the lamp breaks or stops working may vary greatly depending

on the individual lamp characteristics and the operating environment. These are normal characteristics of mercury

lamps. You should always have a spare lamp ready in case it is needed.

• YAMAHA takes no responsibility for loss or damage caused by damage to the projector or operating failures

outside normal service warranty conditions.

Lamp Operating Errors

The mercury lamp that is used as the light source for this projector may stop operating on occasions. This is a normal

characteristic of mercury lamps. If the lamp does not turn on when the projector's power is turned on, remove the

lamp and check if it is broken. If the lamp is not broken, reinstall it. Refer to "Replacing the Lamp" on page 48 of this

manual for instruction on removing and reinstalling the lamp.

If the lamp is broken, replace it with a new lamp. It is recommended that you have a spare lamp ready at all times in

case it is needed.

Notes on Carrying the Projector

• Turn off the projector power and then disconnect the power cord from the electrical outlet.

Furthermore, check that all other cables have been disconnected.

• Attach the lens cap to the lens.

• Retract the adjustable foot.

• If your model of projector has a handle, hold the projector by the handle when carrying it.

3

Accessories

Check the included accessories

Remote control Setup guide

Battery LR6 (AA) x 2 Power cord

4

Features of the Projector

80-inch

screen

Adoption of a wide 1280 x 720 dot panel

This panel allows high-definition images to be

reproduced accurately.

Adoption of a special high-resolution DCDi video circuit developed by Faroudja.

This circuit greatly reduces the jagged edges that

resulted from conventional progressive conversion,

to produce much smoother and natural movement.

(p.30)

Includes 5 picture modes

You can select the desired color mode to match the

images being projected from five preset modes in order

to obtain the optimum image quality.

(p.14)

Includes a variety of color adjustment modes

Various color settings can be adjusted to suit

your preferences, from individual RGB balance

adjustment to setting the color temperature of

your choice. The adjusted settings can then be

stored in memory and recalled at a touch of a

button on the remote control.

(p.24, 25)

Adoption of a short focal-length lens that can project onto 80-inch screens

at distances of 2.5m (8.2 ft.)

This lens is ideal for projecting onto large

indoor screens. The projector can also

project onto 80-inch screens in rooms

with an area of about 10 m

2

.

(Refer to the Setup Guide.)

2.5m

1280

720

5

Basic Operations

This chapter describes basic operations such as turning the projector on and off and adjusting the

projected images.

Turning On the Projector.................................................................. 6

•

••

• Connecting the Power Cord ........................................................................................6

•

••

• Turning On the Power and Projecting Images..........................................................7

Turning Off the Projector.................................................................. 9

Adjusting the Screen Image ........................................................... 11

•

••

• Adjusting the Image Size ...........................................................................................11

•

••

• Adjusting the Image Angle ........................................................................................11

•

••

•

Correcting Keystone Distortion ................................................................................12

•

••

• Displaying a Test Pattern...........................................................................................13

Adjusting the Image Quality........................................................... 14

•

••

• Focusing the Screen Image ........................................................................................14

•

••

• Selecting the picture mode.........................................................................................14

•

••

• Selecting the Image Aspect Ratio..............................................................................15

• Normal mode...................................................................................................................................15

• Squeeze mode..................................................................................................................................16

• Zoom mode .....................................................................................................................................16

• Zoom -Subtitle- mode .....................................................................................................................16

• Through mode .................................................................................................................................17

• Squeeze Through mode...................................................................................................................17

•

••

•

Automatic Adjustment of Computer Images...........................................................17

6

Turning On the Projector

This section describes the procedure from turning on the power to projecting images.

Procedure

1

Check that the power is turned off for

the projector and all components

connected to the projector.

2

Connect the computer or other video

source to the projector.

Refer to the Setup Guide.

3

Remove the lens cap.

4

Connect the accessory power cord to

the projector.

Check that the power cord connector is facing the

same way as the power inlet on the projector, and

then insert the power cord connector securely into

the projector.

5

Connect the other end of the power

cord to a grounded electrical outlet.

6

Turn on the main power switch at the

rear of the projector.

Wait until the indicator lights orange and

the projector goes to the standby condition.

Connecting the Power Cord

Be sure to read the Safety Instructions in this manual for details on safe handling when using

the projector.

Lights orange

7

Basic Operations

Procedure

1

Turn on the power for all equipment

connected to the projector.

For a video source, press the [Play] button at the

video source to start playback if necessary.

Check that the indicator on the projector has

stopped flashing and lights orange.

2

Press the [STANDBY/ON] button on

either the remote control or the

projector's control panel to turn on the

power.

The indicator flashes green, and after a

short period projection starts.

Check that the indicator has stopped

flashing and lights green. (This takes

approximately 15 seconds.)

3

If more than one signal source has been connected, use the remote control or

control panel buttons to select the port which the signal source that you

would like to use is connected to, while referring to the following table.

*The display disappears approximately 1 second after the signal is output.

Turning On the Power and Projecting Images

The buttons on the remote control and the projector's control panel cannot be operated

while the indicator is flashing green. Wait until it lights steadily.

The message "No Signal" may appear depending on the projector's menu settings. (p.31)

Port

Button to press

Display at top-right of

screen *

Projector Remote control

INPUT A

[INPUT]

[A]

INPUT A (component) or

INPUT A (RGB)

INPUT B [B]

INPUT B (component) or

INPUT B (RGB)

S VIDEO [S VIDEO] S Video

VIDEO [VIDEO] Video

D4 VIDEO [D4] D4 Video

DVI [DVI] DVI

Lights green

Remote control

Projector

Connecting the Power Cord

Turning On the Power and Projecting Images

Turning On the Projector

8

•

••

•

If only one signal source has been connected, the signals from that source will be

projected without needing to press one of the above buttons.

•

••

•

If video signals are being input to several input ports simultaneously, interference

between the various signals may occur, and this may cause interference in the projected

images. If this happens, turn off the power supply or disconnect the video equipment

which is not currently being used.

•

••

•

If the "No Signal" message does not disappear, check the connections again.

No images will be projected during the time that it takes for signals to be input from the

video source.

•

••

•

If a laptop computer or a computer with an LCD screen has been connected to the

projector, the images may not be projected straight away. After making the connections,

check that the computer has been set up to output signals.

The following table shows examples of how to toggle output settings. For details, refer to

the section of the documentation provided with your computer under a heading such as

"External output", "Connecting an external monitor" or similar.

NEC Panasonic Toshiba IBM Sony Fujitsu Macintosh

[Fn]+[F3] [Fn]+[F3] [Fn]+[F5] [Fn]+[F7] [Fn]+[F7] [Fn]+[F10]

After startup, change the

Control Panel adjustments

so that Mirroring is active.

9

Basic Operations

Turning Off the Projector

Follow the procedure below to turn off the power of the projector.

Procedure

1

Turn off the power for the signal

sources that are connected to the

projector.

Check that the power for all connected

components has been tuned off.

2

Press the [STANDBY/ON] button on

either the remote control or the

projector's control panel.

The confirmation message shown at left will

appear.

If you do not want to turn off the power, press

any button except the [STANDBY/ON] button.

If you do not carry out any operation, the

message will disappear after seven seconds. (The

power will not turn off at this time.)

3

Press the [STANDBY/ON] button on the

projector's control panel or remote

control once more.

The lamp will switch off. The indicator will

flash red and cool-down

will start.

After about 90 seconds, the indicator will

change to flashing orange.

4

Check that the indicator has

changed to light orange.

When the indicator lights orange,

cool-down is complete.

The cool-down period lasts for approximately 5

minutes. (This varies depending on factors such

as the ambient air temperature.)

The cool-down period is a 5 minutes long in

order to allow the heat inside the projector to

dissipate sufficiently.

The buttons on the control panel and

remote control cannot be operated while

the indicator is flashing red. Wait until

the indicator flashes orange (takes

approximately 90 seconds).

Please Press Key Again

To Power Off

Projector

Remote control

Lights orange

Turning Off the Projector

10

5

If not using the projector for long

periods of time, turn off the main power

switch at the rear of the projector.

6

Retract the front adjustable foot if it is

extended.

Turn the front adjustable foot to retract it.

7

Attach the lens cap.

Attach the lens cap to the lens when not using the

projector, in order to stop the lens from getting

dusty or dirty.

Do not turn off the main power switch at the rear of the projector while the cool-down

is in progress. If the main power switch is turned off before cool-down is complete,

wait for the lamp to cool down (normally about one hour is required) before turning

the power back on again. If the power is turned off and on before the lamp has

cooled down, it may result in lamp operating errors.

Refer to "Lamp operating error" on page 36.

11

Basic Operations

Adjusting the Screen Image

You can adjust the screen image in order to obtain the best possible picture.

The size of the projected image is basically determined by the distance from the projector to the screen.

(Refer to the Setup Guide.)

The following procedures explain how to adjust the screen image once the projector itself has been set up.

Procedure

Turn the zoom ring on the projector to

adjust the image.

The image can be enlarged in this way to 1.35

times the normal size.

If you would like to enlarge the image further,

move the projector further away from the screen.

(Refer to the Setup Guide.)

The projector should be as perpendicular to the screen as possible.

If the projector cannot be set up so that it is exactly perpendicular to the screen, it can be set up so that it is

tilting slightly horizontally or vertically. To tilt the projector upward, adjust the front adjustable foot to tilt

the projector at an angle of up to a maximum 12.9°.

Procedure

Turn the front adjustable foot

underneath the projector to adjust the

projector angle.

Turn the front adjustable foot until the desired

projection angle is obtained.

Adjusting the Image Size

Adjusting the Image Angle

•

••

•

When the foot is adjusted, it may cause the projected images to become distorted. Use the

keystone correction function to adjust this distortion. (p.12)

•

••

•

If the projector is tilted horizontally, turn the rear adjustable feet at left and right to adjust the

horizontal angle.

To reduce

To enlarge

Zoom ring

Seen from the side

Seen from above

Extend

Retract

Rear

adjustable foot

Extend

Retract

Extend

Rear

adjustable foot

Adjusting the Image Size Correcting Keystone

Distortion

Adjusting the Image Angle Displaying a Test

Pattern

Adjusting the Screen Image

12

If the projector is set up so that it is at an angle to the screen, a type of distortion known as "keystone

distortion" may occur.

Keystone correction can be carried out if the angle of the projector is within a range of approximately 15°

vertically from the perpendicular.

Procedure

Correcting Keystone Distortion

•

••

•

When keystone correction is carried out, the projected image will become smaller.

•

••

•

The keystone correction settings are memorized, so that if you change the position or angle of

the projector, you may need to readjust the keystone correction settings.

•

••

•

If the images become uneven in appearance after keystone correction is carried out, decrease

the “Sharpness” setting. (p.27, 29)

•

••

•

Keystone correction can also be carried out using the projector menu. (p.31)

•

••

•

If the value displayed in the gauge on the screen stops changing when horizontal or vertical

keystone correction is being carried out, it indicates that the limit for horizontal or vertical

keystone correction has been exceeded. Check that the projector has not been set up at an

angle which exceeds the proper limit.

Approx. 15° above

Approx. 15° below

15°

While holding down the

[SHIFT] button on the

projector's control panel, press

the or button.

Projector Projector

13

Basic Operations

When setting up the projector, you can project a test pattern onto the screen and use this test pattern to adjust

the projected images before a video source has been connected. The following two types of test pattern are

available.

•

••

•

Crosshatch

•

••

•

Grayscale pattern

The test pattern changes as shown below each time the [PATTERN] button on either the remote control or

the projector's control panel is pressed.

Crosshatch → Grayscale pattern → No pattern

Displaying a Test Pattern

The full menu cannot be displayed while a test pattern is being projected. If you need to change a

setting, press the button on either the projector's control panel or the remote control to display

the line menu, and then change the setting. To correct keystone distortion while a test pattern is

being displayed, press and hold the [SHIFT] button and then use the and buttons on the

projector's control panel to make the adjustment. This setting cannot be made using the remote

control.

This can be used to adjust the focus and correct keystone distortion.

This can be used to adjust dark and light shades to the desired shade.

Use the "Color Temp.

", "Flesh Tone" and "Color Balance"

commands in the "Image" menu to adjust the settings.

Adjusting the Image Size Correcting Keystone

Distortion

Adjusting the Image Angle Displaying a Test

Pattern

14

Adjusting the Image Quality

The quality of the screen images can be adjusted as follows.

Procedure

Turn the focus ring to adjust the image

focus.

The following five color modes have been preset for use with images with varying characteristics. You can

use these color modes to obtain the optimum image quality easily, just by selecting whichever color mode

best suits the images. The brightness of the projected images will vary depending on the mode.

Procedure

The picture mode changes as shown

below each time the [PICTURE MODE]

button on the projector's control panel

or the [PICTURE] button on the remote

control is pressed.

A → B → C → PC → sRGB

The current setting appears on the screen each

time the color mode changes.

Focusing the Screen Image

•

••

•

If the surface of the lens is dirty or misted

over as a result of condensation, it may

not be possible to adjust the focus

correctly. If this happens, clean or de-mist

the lens. (p.46)

•

••

•

If the projector is positioned outside the

normal projecting range of 0.9 - 13 m (2.9

- 42.6 ft.), it may not be possible to obtain

the correct focus. If you have trouble

obtaining the correct focus, check the

projection distance.

Selecting the picture mode

Mode name Gamma Color Temp

Priority

element

Use

A Original 1 6700 K

(adjustable)

Color Ideal for enjoying presentations in a natural

atmosphere.

B Original 2 6700 K

(adjustable)

Color Ideal for enjoying presentations such as movies which

have large numbers of dark scenes.

C Original 3 6700 K

(adjustable)

Color Ideal for projecting images with greater modulation

and intensity.

PC 2.2

(Basic)

7500 K

(adjustable)

Brightness Ideal for use in making images as bright as possible

when projecting computer images.

sRGB 2.2

(Basic)

6500 K (fixed) Color Images conform to the sRGB

standard. If the

connected video source has an sRGB mode, set both

the projector and the video source to sRGB.

The color mode setting can also be

changed using the "Picture Mode" item of

the projector's "Image" menu. (p.27, 28)

Focus ring

Projector Remote control

Picture B

15

Basic Operations

The aspect ratio for projected images can be selected from the following five types of setting. However,

the aspect ratio settings that can be selected will vary depending on the input signal.

Procedure

For Video (SDTV) signals, the aspect

mode changes in the following order

each time the [ASPECT] button on

either the projector's control panel or

the remote control is pressed.

Normal → Squeeze → Zoom → Zoom -Subtitle-

→ Through → Squeeze Through

The current setting appears on the screen each

time the aspect ratio changes.

Details of each aspect ratio are as follows.

Selecting the Image Aspect Ratio

Input signal Normal Squeeze Zoom

Zoom

-Subtitle-

Through Squeeze Through

Video (SDTV

)

OO O O O O

Video (HDTV )

O- - -

O

(720p only)

-

Computer (SVGA or lower)

O- O - O -

Computer (XGA or higher)

O- O - - -

Do not use the aspect mode function to elongate or compress image that are being projected for

commercial purposes or in public places such as hotel lobbies or stores, as doing so may infringe

the rights of the original copyright owner for the images under copyright protection laws.

Normal mode

Projector

Remote control

Normal

The aspect ratio of the images being input

is maintained, and the images are

projected into a 16:9 screen area.

When 4:3 images are being projected,

black bands will appear at the left and

right of the image as shown in the

illustration at left.

4:3

i

mage

Focusing the

Screen Image

Selecting the Image

Aspect Ratio

Selecting the

Picture Mode

Automatic Adjustment

of Computer Images

Sidan laddas ...

Yamaha LPX-500 Användarmanual

Yamaha LPX-500 Användarmanual

på andra språk

Relaterade papper

Andra dokument