RX-E600
OWNER’S MANUAL
MODE D’EMPLOI
Receiver
Récepteur
0101RXE600_CA_H1_EN.p65 2004.09.02, 14:301
i
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
• Explanation of Graphical Symbols
The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended to alert
you to the presence of uninsulated “dangerous
voltage” within the product’s enclosure that may
be of sufficient magnitude to constitute a risk of
electric shock to persons.
The exclamation point within an equilateral
triangle is intended to alert you to the presence of
important operating and maintenance (servicing)
instructions in the literature accompanying the
appliance.
1 Read Instructions – All the safety and operating instructions
should be read before the product is operated.
2 Retain Instructions – The safety and operating instructions
should be retained for future reference.
3 Heed Warnings – All warnings on the product and in the
operating instructions should be adhered to.
4 Follow Instructions – All operating and use instructions
should be followed.
5 Cleaning – Unplug this product from the wall outlet before
cleaning. Do not use liquid cleaners or aerosol cleaners. Use
a damp cloth for cleaning.
6 Attachments – Do not use attachments not recommended by
the product manufacturer as they may cause hazards.
7 Water and Moisture – Do not use this product near water –
for example, near a bath tub, wash bowl, kitchen sink, or
laundry tub; in a wet basement; or near a swimming pool;
and the like.
8 Accessories – Do not place this product on an unstable cart,
stand, tripod, bracket, or table. The product may fall,
causing serious injury to a child or adult, and serious
damage to the product. Use only with a cart, stand, tripod,
bracket, or table recommended by the manufacturer, or sold
with the product. Any mounting of the product should
follow the manufacturer’s instructions, and should use a
mounting accessory recommended by the manufacturer.
9 A product and cart combination should be
moved with care. Quick stops, excessive
force, and uneven surfaces may cause the
product and cart combination to overturn.
10 Ventilation – Slots and openings in the cabinet are provided
for ventilation and to ensure reliable operation of the
product and to protect it from overheating, and these
openings must not be blocked or covered. The openings
should never be blocked by placing the product on a bed,
sofa, rug, or other similar surface. This product should not
be placed in a built-in installation such as a bookcase or rack
unless proper ventilation is provided or the manufacturer’s
instructions have been adhered to.
11 Power Sources – This product should be operated only from
the type of power source indicated on the marking label. If
you are not sure of the type of power supply to your home,
consult your product dealer or local power company. For
products intended to operate from battery power, or other
sources, refer to the operating instructions.
12 Grounding or Polarization – This product may be equipped
with a polarized alternating current line plug (a plug having
one blade wider than the other). This plug will fit into the
power outlet only one way. This is a safety feature. If you
are unable to insert the plug fully into the outlet, try
reversing the plug. If the plug should still fail to fit, contact
your electrician to replace your obsolete outlet. Do not
defeat the safety purpose of the polarized plug.
13 Power-Cord Protection – Power-supply cords should be
routed so that they are not likely to be walked on or pinched
by items placed upon or against them, paying particular
attention to cords at plugs, convenience receptacles, and the
point where they exit from the product.
14 Lightning – For added protection for this product during a
lightning storm, or when it is left unattended and unused for
long periods of time, unplug it from the wall outlet and
disconnect the antenna or cable system. This will prevent
damage to the product due to lightning and power-line
surges.
15 Power Lines – An outside antenna system should not be
located in the vicinity of overhead power lines or other
electric light or power circuits, or where it can fall into such
power lines or circuits. When installing an outside antenna
system, extreme care should be taken to keep from touching
such power lines or circuits as contact with them might be
fatal.
16 Overloading – Do not overload wall outlets, extension
cords, or integral convenience receptacles as this can result
in a risk of fire or electric shock.
17 Object and Liquid Entry – Never push objects of any kind
into this product through openings as they may touch
dangerous voltage points or short-out parts that could result
in a fire or electric shock. Never spill liquid of any kind on
the product.
18 Servicing – Do not attempt to service this product yourself
as opening or removing covers may expose you to
dangerous voltage or other hazards. Refer all servicing to
qualified service personnel.
19 Damage Requiring Service – Unplug this product from the
wall outlet and refer servicing to qualified service personnel
under the following conditions:
a) When the power-supply cord or plug is damaged,
b) If liquid has been spilled, or objects have fallen into
the product,
c) If the product has been exposed to rain or water,
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,
DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION
IMPORTANT SAFETY INSTRUCTIONS
0102RXE600_CA_Cau_EN.p65 2004.09.02, 14:302
ii
1. IMPORTANT NOTICE : DO NOT MODIFY THIS
UNIT!
This product, when installed as indicated in the
instructions contained in this manual, meets FCC
requirements. Modifications not expressly approved
by Yamaha may void your authority, granted by the
FCC, to use the product.
2. IMPORTANT : When connecting this product to
accessories and/or another product use only high
quality shielded cables. Cable/s supplied with this
product MUST be used. Follow all installation
instructions. Failure to follow instructions could void
your FCC authorization to use this product in the USA.
3. NOTE : This product has been tested and found to
comply with the requirements listed in FCC
Regulations, Part 15 for Class “B” digital devices.
Compliance with these requirements provides a
reasonable level of assurance that your use of this
product in a residential environment will not result in
harmful interference with other electronic devices.
This equipment generates/uses radio frequencies and,
if not installed and used according to the instructions
found in the users manual, may cause interference
harmful to the operation of other electronic devices.
Compliance with FCC regulations does not guarantee
that interference will not occur in all installations. If
this product is found to be the source of interference,
which can be determined by turning the unit “OFF” and
“ON”, please try to eliminate the problem by using one
of the following measures:
Relocate either this product or the device that is being
affected by the interference.
Utilize power outlets that are on different branch (circuit
breaker or fuse) circuits or install AC line filter/s.
In the case of radio or TV interference, relocate/reorient
the antenna. If the antenna lead-in is 300 ohm ribbon
lead, change the lead-in to coaxial type cable.
If these corrective measures do not produce satisfactory
results, please contact the local retailer authorized to
distribute this type of product. If you can not locate the
appropriate retailer, please contact Yamaha Electronics
Corp., U.S.A. 6660 Orangethorpe Ave, Buena Park, CA
90620.
The above statements apply ONLY to those products
distributed by Yamaha Corporation of America or its
subsidiaries.
EXAMPLE OF ANTENNA GROUNDING
MAST
GROUND
CLAMP
ANTENNA
LEAD IN
WIRE
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810–20)
GROUNDING CONDUCTORS
(NEC SECTION 810–21)
GROUND CLAMPS
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250. PART H)
ELECTRIC
SERVICE
EQUIPMENT
NEC
– NATIONAL ELECTRICAL CODE
FCC INFORMATION (for US customers)
Note to CATV system installer:
This reminder is provided to call the CATV system installer’s
attention to Article 820-40 of the NEC that provides
guidelines for proper grounding and, in particular, specifies
that the cable ground shall be connected to the grounding
system of the building, as close to the point of cable entry as
practical.
d) If the product does not operate normally by following
the operating instructions. Adjust only those controls
that are covered by the operating instructions as an
improper adjustment of other controls may result in
damage and will often require extensive work by a
qualified technician to restore the product to its normal
operation,
e) If the product has been dropped or damaged in any
way, and
f) When the product exhibits a distinct change in
performance - this indicates a need for service.
20 Replacement Parts – When replacement parts are required,
be sure the service technician has used replacement parts
specified by the manufacturer or have the same
characteristics as the original part. Unauthorized
substitutions may result in fire, electric shock, or other
hazards.
21 Safety Check – Upon completion of any service or repairs
to this product, ask the service technician to perform safety
checks to determine that the product is in proper operating
condition.
22 Wall or Ceiling Mounting – The unit should be mounted to
a wall or ceiling only as recommended by the manufacturer.
23 Heat – The product should be situated away from heat
sources such as radiators, heat registers, stoves, or other
products (including amplifiers) that produce heat.
24 Outdoor Antenna Grounding – If an outside antenna or
cable system is connected to the product, be sure the
antenna or cable system is grounded so as to provide some
protection against voltage surges and built-up static charges.
Article 810 of the National Electrical Code, ANSI/NFPA 70,
provides information with regard to proper grounding of the
mast and supporting structure, grounding of the lead-in wire
to an antenna discharge unit, size of grounding conductors,
location of antenna discharge unit, connection to grounding
electrodes, and requirements for the grounding electrode.
IMPORTANT SAFETY INSTRUCTIONS
0102RXE600_CA_Cau_EN.p65 2004.09.02, 14:303
1 To assure the finest performance, please read this
manual carefully. Keep it in a safe place for future
reference.
2 Install this unit in a well ventilated, cool, dry, clean
place away from direct sunlight, heat sources, vibration,
dust, moisture or cold. In a cabinet, allow about 10 cm
(4 in.) of free space all around RX-E600 for adequate
ventilation.
3 Locate this unit away from other electrical appliances,
motors, or transformers to avoid humming sounds.
4 Do not expose this unit to sudden temperature changes
from cold to hot, nor locate this unit in an environment
with high humidity (i.e., a room with a humidifier) to
prevent condensation inside this unit, which may cause
an electrical shock, fire, damage to this unit, and/or
personal injury.
5 Avoid installing this unit in a location where foreign
objects may fall onto this unit or where this unit may be
exposed to liquid dripping or splashing. On the top of
this unit, do not place:
• Other components, as they may cause damage and/or
discoloration on the surface of this unit.
• Burning objects (i.e., candles), as they may cause fire,
damage to this unit, and/or personal injury.
• Containers with liquid in them, as they may fall, spilling
the liquid and causing an electrical shock to the user
and/or damage to this unit.
6 Do not cover this unit with a newspaper, tablecloth,
curtain, etc. in order not to obstruct heat radiation. If the
temperature inside this unit rises, it may cause fire,
damage to this unit, and/or personal injury.
7 Do not plug in this unit to a wall outlet until all
connections are complete.
8 Do not operate this unit upside-down. It may overheat,
possibly causing damage.
9
Do not use excessive force on switches, knobs and/or cords.
10 When disconnecting the power cord from the wall
outlet, grasp the plug; do not pull the cord.
11 Do not clean this unit with chemical solvents; this might
damage the finish. Use a clean, dry cloth.
12 Use only the voltage specified on this unit. Using this
unit with a higher voltage than specified is dangerous
and may cause fire, damage to this unit, and/or personal
injury. YAMAHA will not be held responsible for any
damage resulting from use of this unit with a voltage
other than as specified.
13 To prevent damage by lightning, disconnect the power
cord from the wall outlet during an electrical storm.
14 Do not attempt to modify or fix this unit. Contact
qualified YAMAHA service personnel when any service
is needed. The cabinet should never be opened for any
reason.
15 When not planning to use this unit for long periods of
time (i.e., vacation), disconnect the AC power plug from
the wall outlet.
CAUTION: READ THIS BEFORE OPERATING THIS UNIT
16 Be sure to read the “Troubleshooting” section on
common operating errors before concluding that this
unit is faulty.
17 Before moving this unit, press STANDBY/ON to set the
unit in standby mode, then disconnect the AC power
plug from the wall outlet.
18 VOLTAGE SELECTOR (General model only)
The VOLTAGE SELECTOR on the rear panel of this
unit must be set for your local main voltage BEFORE
plugging into the AC main supply. Voltages are 110/120/
220/230-240 V AC, 50/60 Hz.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,
DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.
The unit is not disconnected from the AC power
source as long as it is connected to the wall outlet,
even if this unit itself is turned off. This state is
called the standby mode. In this state, this unit is
designed to consume a very small quantity of
power.
FOR CANADIAN CUSTOMERS
To prevent electric shock, match wide blade of plug
to wide slot and fully insert.
This Class B digital apparatus complies with
Canadian ICES-003.
(U.S.A., Canada and General models)
The nameplate is located on the bottom of the unit.
iii
We Want You Listening For A Lifetime
YAMAHA and the Electronic Industries Association’s Consumer
Electronics Group want you to get the most out of your equipment
by playing it at a safe level. One that lets the sound come through
loud and clear without annoying blaring or distortion – and, most
importantly, without affecting your sensitive hearing.
Since hearing damage from loud sounds is often
undetectable until it is too late, YAMAHA and the
Electronic Industries Association’s Consumer
Electronics Group recommend you to avoid
prolonged exposure from excessive volume levels.
IMPORTANT
Please record the serial number of this unit in the space
below.
MODEL:
Serial No.:
The serial number is located on the bottom of the unit.
Retain this Owner’s Manual in a safe place for future
reference.
0102RXE600_CA_Cau_EN.p65 2004.09.02, 14:304
1
English
FEATURES
• Minimum RMS output power per
channel 40 W + 40 W
(6Ω, 20 Hz to 20 kHz, 0.1% THD)
• System remote control
• 40-station FM/AM preset tuning
• SUBWOOFER output terminal
The receiver (RX-E600) and DVD player (DVD-E600) are the main units of the YAMAHA Piano Craft Series.
You can upgrade the system by adding the cassette deck (KX-E300) and MD recorder (MDX-E300)*.
* MD recorder (MDX-E300) may not be available for some areas.
CONTENTS
SUPPLIED ACCESSORIES ....................... 2
GETTING STARTED
Remote control .................................................... 3
Connecting the speakers and antennas ................ 4
Connecting the system......................................... 5
Setting the clock .................................................. 6
NAMES OF BUTTONS AND CONTROLS
Front panel ........................................................... 7
Display................................................................. 7
Remote control .................................................... 8
BASIC OPERATIONS
Listening to a source............................................ 9
TUNING
Listening to the radio ......................................... 10
Presetting stations .............................................. 11
USING THE BUILT-IN TIMER
Before using the timer ....................................... 12
Timer play and recording .................................. 12
Sleep timer ......................................................... 13
SYSTEM CONTROL
Controlling other components ........................... 14
Before recording ................................................ 16
Dubbing setting ................................................. 16
ADDITIONAL INFORMATION
Troubleshooting ................................................. 17
Specifications .................................................... 19
0103RXE600_CA_01-02_E.p65 2004.09.02, 14:311
2
SUPPLIED ACCESSORIES
• AM loop antenna
• Indoor FM antenna
• Batteries (AA, R6, UM-3)
POWER
1 2 3
123
4 5 6
456
7 8 9
78
0 +10 +100
REP
RANDOM
PROG
ABC
TIME
DE
TAPE
DIRECTION
PRESET
TUNER
PRESET
MD DVD TAPE
AUX
MD
REC
/
PAUSE
TAPE
REC
/
PAUSE
MODE
SLEEP
DISPLAY
DUBBING
VOLUME
START
After unpacking, check that the following parts are contained.
• Remote control
(U.S.A., Canada, China,
Korea and General
models)
(Europe, U.K., and
Australia models)
0103RXE600_CA_01-02_E.p65 2004.09.02, 15:292
English
3
Remote control
The remote control for the RX-E600 also controls the
DVD-E600 DVD player, KX-E300 cassette deck, and the
MDX-E300 MD recorder. Operating buttons for each unit
are explained on the pages below:
Receiver, RX-E600: P.8
DVD player, DVD-E600: P.14
Cassette deck, KX-E300: P.15
MD recorder, MDX-E300: P.15
Battery installation
1 Remove the battery compartment cover.
2 Insert batteries into the battery compartment.
3 Replace the battery compartment cover.
Battery replacement
If you find that the remote control must be used closer to
the main unit than usual, the batteries are weak. Replace
batteries with new ones.
Notes
• Use only AA, R6, UM-3 batteries for replacement.
• Be sure the polarities are correct. (See the illustration inside
the battery compartment.)
• Remove the batteries if the remote control will not be used for
an extended period of time.
• If batteries leak, dispose of them immediately. Avoid touching
the leaked material or letting it come in contact with clothing,
etc. Clean the battery compartment thoroughly before
installing new batteries.
Remote control operation range
Notes
• There should be no large obstacles between the remote control
and the main unit.
• Strong light (especially light from inverter-type fluorescent
lamps etc) on the remote conrol sensor may impede the
functioning of the remote control. In this case, reposition the
main unit to avoid direct lighting.
Removing the protection sheet
The remote control is shipped with a protection sheet to
prevent the surface from being scratched during
transportation.
When removing the sheet, first put adhesive tape on an
edge of the remote control so that the tape sticks to the
sheet. Then peel the sheet off with the tape.
Note
• Do not scratch the remote control surface when peeling the
sheet off.
GETTING STARTED
BALANCE
INPUT
VOLUME
L
R
TREBLEBASS
PHONES
STANDBY/ON
TIMER
DISPLAY MEMORY
NATURAL SOUND
STEREO RECEIVER
RX–E600
AUTO/MAN'L
PRESET/BAND
TIMER HOUR MIN
MIN MAX
PRESET/TUNING
TIMER ADJ
+–+–
30°
30°
2
1
3
Remote control
sensor
Within approximately
6 m (20 feet)
P
O
W
E
R
1
1
2
2
3
3
4
4
7
7
8
8
9
5
5
6
6
P
O
W
E
R
1
1
2
2
3
3
4
4
7
7
8
8
9
5
5
6
6
0104RXE600_CA_03-08_E.p65 2004.09.02, 14:323
4
Connecting the speakers and antennas
Do not connect the AC power cord to the wall outlet until all connections have
been completed.
Follow the steps as shown below to connect the system using the supplied cords and accessories. Be sure all connections are
made correctly, that is to say L (left) to L, R (right) to R, “+” to “+” and “–” to “–”.
1 Connect the Speakers.
1 Unscrew the knob.
2 Remove approx. 10 mm (0.4”) of insulation from
each of the speaker wires and insert the bare wire
into the terminal.
3 Tighten the knob to secure the wire.
2 Connect the AM Antenna.
Set up the AM loop antenna, then connect it.
3 Connect the FM Antenna.
4 Connect the AC power cord to a wall outlet.
Notes
• Use external FM/AM antennas if you need better reception.
Consult your dealer.
• The AM loop antenna should be placed apart from the main
unit. The antenna may be hung on a wall.
To connect the subwoofer (optional)
You can reinforce the bass frequencies by adding a
subwoofer (optional).
Connect the SUBWOOFER OUT terminal of the unit to
the INPUT terminal of the subwoofer.
1
3
FM antenna
2 AM loop antenna
Right speaker
Left speaker
GETTING STARTED
Red: positive(+)
Black: negative(–)
GND
AM
ANT
FM ANT
75 Ω UNBAL
1
2
3
FM ANT
75Ω UNBAL.
SYSTEM
CONNECTOR
IN
IN
IN
IN
OUT
OUT
6Ω MIN./SPEAKER
SPEAKERSTUNER
SUBWOOFER
OUT
SYSTEM
CONNECTOR
GND
AM
ANT
TAPE
DVD
AUX
MD
R
L
R L
+
–
A
B
E
C
D
DVD
4 To wall outlet
0104RXE600_CA_03-08_E.p65 2004.09.02, 14:324
English
5
Connecting the system
Connecting the RX-E600 and the DVD-E600
1 Connect ‰ to ‰ using the Audio pin cable.
Insert the plugs into the jacks of the same color.
2 Connect the SYSTEM CONNECTOR (DVD) of the RX-E600 and the SYSTEM CONNECTOR (RECEIVER) of
the DVD-E600 with a system control cable (supplied with the DVD-E600).
*The other SYSTEM CONNECTOR of the RX-E600 is for connecting the MDX-E300 or KX-E300.
3 Connect the AC power plug of the DVD-E600 to AC OUTLET of the RX-E600.
This configuration allows you to turn all components in the system on and off with one touch, and reduces the standby
power consumption of the DVD-E600.
Adding KX-E300 and MDX-E300 to the above system
(For details, refer to the owner's manual supplied with the respective component.)
1 Connect Å and ı of RX-E600 to Å and ı of KX-E300.
2 Connect Ç and Î of RX-E600 to Ç and Î of MDX-E300.
3 Connect an external component to the AUX terminal of RX-E600.
4 Connect DIGITAL OPTICAL OUT of DVD-E600 to DIGITAL OPTICAL IN of MDX-E300.
Take off the covers of the optical fiber cable plug, the DIGITAL OPTICAL OUT jack, and the DIGITAL OPTICAL
IN jack before making digital connections. Be sure to replace the terminal’s cover when the terminal on the rear panel
is not being used, in order to protect from dust.
Caution
• Do not turn RX-E600 on until all connections between components have been completed.
• Do not connect or disconnect the system control cable and/or power cord while the system components are turned on.
AUDIO
OUT
DIGITAL
OUT
VIDEO
OUT
OPTICALCOAXIAL
COMPONENT
VIDEO
S VIDEO
SYSTEM
CONNECTOR
RECEIVER
E
L
R
P
B
Y
P
R
FM ANT
75Ω UNBAL.
SYSTEM
CONNECTOR
IN
IN
IN
IN
OUT
OUT
6Ω MIN./SPEAKER
SPEAKERSTUNER
SUBWOOFER
OUT
SYSTEM
CONNECTOR
GND
AM
ANT
TAPE
DVD
AUX
MD
R
L
R L
+
–
A
B
E
C
D
DVD
*
GETTING STARTED
To wall outlet
To RX-E600
Audio pin cable
<RX-E600>
<DVD-E600>
1
System control cable
2
3
0104RXE600_CA_03-08_E.p65 2004.09.02, 14:325
6
GETTING STARTED
Setting the clock
You must set the clock before you use the timer functions.
The clock is based on a 12-hour system for U.S. and
Canada models, and 24-hour system for Australia model.
1 Turn on the power by pressing STANDBY/ON on
the front panel, or POWER on the remote control.
2 While the power is on, press DISPLAY to display
the time.
3 Press HOUR while holding TIME ADJ to advance
the hour setting.
• Press HOUR while holding TIME ADJ and
PRESET/BAND to reverse the hour setting.
4 Press MIN while holding TIME ADJ to advance the
minute setting.
• Press MIN while holding TIME ADJ and
PRESET/BAND to reverse the minute setting.
To display the clock
Press DISPLAY.
The current time appears for about 8 seconds, then the
normal display returns. Some buttons and controls may
not work while the current time is displayed.
Note
• In the event of a power failure or when the AC power cord is
disconnected for more than five minutes, you must reset the
clock.
HOUR
DISPLAY
PRESET/BANDTIME ADJ
MIN
BALANCE
INPUT
VOLUME
L
R
TREBLEBASS
PHONES
STANDBY/ON
TIMER
DISPLAY MEMORY
NATURAL SOUND
STEREO RECEIVER
RX–E600
AUTO/MAN'L
PRESET/BAND
TIMER HOUR MIN
MIN MAX
PRESET/TUNING
TIMER ADJ
+– +–
STANDBY/ON
0104RXE600_CA_03-08_E.p65 2004.09.02, 14:326
English
7
Display
7 TIMER indicator (P.12)
8 SLEEP indicator (P.13)
1 STANDBY/ON (P.9)
2 TIMER indicator (P.12)
3 DISPLAY (P.12)
4 MEMORY/TIME ADJ (P.6/P.11)
5 AUTO/MAN’L/TIMER (P.10/P.12)
6 PRESET/BAND (P.10)
7 Display (P.7)
8 PRESET/TUNING / (P.10)
HOUR/MIN (P.6/P.12)
1 Multi-information display
2 PRESET indicator (P.11)
3 STEREO indicator (P.10)
4 TUNED indicator (P.10)
5 AUTO indicator (P.10)
6 MEMORY indicator (P.11)
NAMES OF BUTTONS AND CONTROLS
9 VOLUME (P.9)
0 PHONES (P.9)
q Remote control sensor (P.3)
w BASS (P.9)
e TREBLE (P.9)
r BALANCE (P.9)
t INPUT (P.9)
Front panel
BALANCE
INPUT
VOLUME
L
R
TREBLEBASS
PHONES
STANDBY/ON
TIMER
DISPLAY MEMORY
NATURAL SOUND
STEREO RECEIVER
RX–E600
AUTO/MAN'L
PRESET/BAND
TIMER HOUR MIN
MIN MAX
PRESET/TUNING
TIMER ADJ
+– +–
12 345678 9
0 q wer t
TIMER
SLEEP
STEREO AUTO
MEMORY
TUNED
PRESET
123456 78
0104RXE600_CA_03-08_E.p65 2004.09.02, 14:327
8
Remote control
1 POWER (P.9)
2 Preset numbers (P.11)
3 A/B/C/D/E (P.11)
4 PRESET / (P.11)
5 TUNER (RX-E600) (P.11)
6 MD input (MDX-E300) (P.15)
7 TAPE input (KX-E300) (P.15)
8 DVD input (DVD-E600) (P.14)
9 AUX (The equipment connected to the AUX
terminal) (P.5)
0 SLEEP (P.13)
q DISPLAY (P.12)
w VOLUME %/fi (P.9)
Note
• 5 - 9 are operation buttons and input selectors for each
component.
NAMES OF BUTTONS AND CONTROLS
POWER
1 2 3
123
4 5 6
456
7 8 9
78
0 +10 +100
REP
RANDOM
PROG
ABC
TIME
DE
TAPE
DIRECTION
PRESET
TUNER
PRESET
MD DVD TAPE
AUX
MD
REC
/
PAUSE
TAPE
REC
/
PAUSE
MODE
SLEEP
DISPLAY
DUBBING
VOLUME
START
1
2
5
7
8
9
q
w
3
4
6
0
0104RXE600_CA_03-08_E.p65 2004.09.02, 14:328
English
9
BASIC OPERATIONS
Listening to a source
1 Set the volume to “MIN” by turning VOLUME.
2 Turn on the power by pressing STANDBY/ON on
the front panel, or POWER on the remote control.
• Piano Craft series components that have correct
system connections made to RX-E600 can be
controlled to turn to the on or standby mode by
RX-E600. However, once the connected
components are turned to the standby mode with
their respective STANDBY/ON button, they
cannot be controlled by RX-E600 STANDBY/
ON button.
3
Select the desired input source by turning INPUT until a
suitable source component name appears on the display.
• When you operate the component connected to the
AUX terminal, turn INPUT to select AUX.
4
Start playback on the source component. (Refer to the
owner’s manual supplied with each selected component.)
5 Adjust the volume level by turning VOLUME on the
front panel or pressing VOLUME %/fi on the remote
control.
6 If desired, adjust BASS, TREBLE, and BALANCE.
BASS: Turn this control clockwise to increase (or
counterclockwise to decrease) the low frequency
response.
TREBLE: Turn this control clockwise to increase (or
counterclockwise to decrease) the high frequency
response.
BALANCE: Adjust the balance of the output volume
from the left and right speakers to compensate for
sound imbalance caused by the speaker location or
listening room conditions.
When you use headphones
Connect the headphones to the PHONES jack. You can
listen to the sound to be output from the main speakers
through the headphones.
When you have finished using this unit
Press STANDBY/ON on the front panel again or
POWER on the remote control to set this unit to the
standby mode.
Auto standby function
This unit will automatically place itself in standby mode
under the following conditions:
• When you select a component connected to this unit
with a system control cable as an input source.
• The source component is stopped and has not been
operated for 30 minutes.
VOLUME
STANDBY/ON
INPUT
BALANCE
TREBLE
BASSPHONES
BALANCE
INPUT
VOLUME
L
R
TREBLEBASS
PHONES
STANDBY/ON
TIMER
DISPLAY MEMORY
NATURAL SOUND
STEREO RECEIVER
RX–E600
AUTO/MAN'L
PRESET/BAND
TIMER HOUR MIN
MIN MAX
PRESET/TUNING
TIMER ADJ
+–+–
POWER
VOLUME %/fi
POWER
1 2 3
123
4 5 6
456
7 8 9
78
0 +10 +100
REP
RANDOM
PROG
ABC
TIME
DE
TAP E
DIRECTION
PRESET
TUNER
PRESET
MD DVD TAPE
AUX
MD
REC
/
PAUSE
TAPE
REC
/
PAUSE
MODE
SLEEP
DISPLAY
DUBBING
VOLUME
START
0105RXE600_CA_09-09_E.p65 2004.09.02, 14:339
TUNING
10
Automatic tuning
1 Select TUNER by turning INPUT so that the
frequency of a radio station appears in the display.
2 Press PRESET/BAND to select the reception band.
Do not select the preset tuning mode (in which
“PRESET” appears on the display).
3 Press AUTO/MAN’L so that “AUTO” appears in the
display.
4 Press PRESET/TUNING (For a higher
frequency) or
(For a lower frequency).
5 The unit starts searching for a station.
When the unit finds a station, it stops searching and
“TUNED” appears on the display.
6 If the station located is not the one you want, repeat
steps 4 and 5 until you find a suitable station.
Notes
• If automatic tuning search does not find the desired station, try
manual tuning as described next.
• When an FM stereo broadcast with sufficient signal strength is
received, “STEREO” appears on the display and you can listen
to stereo sound.
Listening to the radio
You can find radio stations automatically and manually.
Manual tuning
1 Follow steps 1 and 2 described in “Automatic
tuning.”
2 Press AUTO/MAN’L so that “AUTO” disappears
from the display.
3 Press PRESET/TUNING (for a higher
frequency) or
(for a lower frequency) to select
your desired station.
• The frequency changes incrementally each time
you press PRESET/TUNING.
STEREO AUTO
TUNED
PRESET/TUNING /
PRESET/BAND
BALANCE
INPUT
VOLUME
L
R
TREBLEBASS
PHONES
STANDBY/ON
TIMER
DISPLAY MEMORY
NATURAL SOUND
STEREO RECEIVER
RX–E600
AUTO/MAN'L
PRESET/BAND
TIMER HOUR MIN
MIN MAX
PRESET/TUNING
TIMER ADJ
+–+–
INPUT
AUTO/MAN’L
0106RXE600_CA_10-11_E.p65 2004.09.02, 14:3310
English
TUNING
English
11
To preset stations manually
1 Tune in a desired station.
(Refer to the previous page for the tuning procedure.)
2 Press MEMORY.
3 Within about 5 seconds, use PRESET/TUNING
/ to select a desired preset number. Continue
pressing PRESET/TUNING
/ to select the
group of the preset stations (A, B, C, D, and E).
4 Press MEMORY.
• “MEMORY”, “PRESET”, and preset number will
appear on the display.
5 Repeat steps 1 to 4 until all desired stations are
preset.
Notes
• A new setting can be preset in place of a previous one.
• The preset stations are retained for a week after you disconnect
the AC power cord or a power failure occurs.
Presetting stations
The unit can store station frequences selected using
Automatic or Manual tuning as presets. Up to 40 stations
can be stored. With this function, you can select any
desired station by pressing the corresponding preset
station number.
To preset stations automatically
1 Select TUNER as input source by turning INPUT.
2 Press MEMORY for about 2 seconds.
• The unit starts presetting stations, “AUTO” and
“MEMORY” will flash on the display.
Received stations are stored to A1, A2...A8 sequentially.
After 40 stations or all FM and AM stations are stored, the
display will show the preset station A1.
To recall a preset station
Press TUNER and select the desired number by pressing
PRESET/BAND and PRESET/TUNING
/ on the
front panel or PRESET
/ , A/B/C/D/E and 1–8 on
the remote control.
The arrow will appear for a second when
it is preset.
INPUTPRESET/BANDMEMORY
1–8
A/B/C/D/E
TUNER
PRESET /
BALANCE
INPUT
VOLUME
L
R
TREBLEBASS
PHONES
STANDBY/ON
TIMER
DISPLAY MEMORY
NATURAL SOUND
STEREO RECEIVER
RX–E600
AUTO/MAN'L
PRESET/BAND
TIMER HOUR MIN
MIN MAX
PRESET/TUNING
TIMER ADJ
+– +–
PRESET/TUNING /
STEREO
TUNED
MEMORY
PRESET
STEREO
TUNED MEMORY
PRESET
POWER
1 2 3
123
4 5 6
456
7 8 9
78
0 +10 +100
REP
RANDOM
PROG
ABC
DE
TAPE
DIRECTION
PRESET
TUNER
PRESET
MD TAPE
AUX
MD
REC
/
PAUSE
TAPE
REC
/
PAUSE
MODE
SLEEP
DISPLAY
DUBBING
VOLUME
START
TIME
DVD
0106RXE600_CA_10-11_E.p65 2004.09.02, 14:3311
12
Timer play and recording
By using the built-in timer, you can have the unit turn on
at a specified time and begin playing or recording
automatically. You can also specify the time at which you
want the unit to turn off.
3. Timer REC
Select the recording component by turning
INPUT. If you wish to enjoy timer playback with
the TUNER or AUX settings, select “REC Mode
OFF”.
4. ON Time
“ON Time” appears on the display for a second,
and changed to the time setting mode.
Press HOUR to set the hour.
Press MIN to set the minute.
5. OFF Time
Set the time the same way as above.
If you set the ON time but not OFF time, timer
play or recording will finish automatically after an
hour.
Notes
• The display mode changes after approximately 8 seconds.
If you change the mode before completing setting, press
DISPLAY once or more to return to the desired mode.
• If you select the input other than TUNER and AUX on
“2. Timer Input”, “3. Timer REC” is skipped.
2 Press TIMER to complete the timer setting.
The system changes to the standby mode.
• TIMER indicator lights up.
If you continue using the system, press STANDBY/
ON to turn on this unit.
To cancel the timer play setting
Press DISPLAY to show the current time, then press
TIMER so that “TIMER” disappears from the display.
You can also cancel the timer play setting by pressing
TIMER when the unit is in standby mode.
Note
• In the event of a power failure or when the AC power cord is
disconnected for more than five minutes, you must reset the
clock.
1 Press DISPLAY.
Whenever DISPLAY is pressed, the display mode
changes as follows:
1. Clock Time (TIMER on/off mode)
If you have not set the clock yet “Set Clock”
appears. You need to set the current time as
described on page 6.
2. Timer Input
Select the source to be played by turning INPUT.
• Timer recording is possible only when you
select TUNER or AUX.
MIN
INPUT
DISPLAY HOUR
TIMER
Before using the timer
If you want to use the cassette deck, KX-E300 or the MD
Recorder, MDX-E300 for timer play or recording, you
must first make the connections as shown in “Connecting
the system” on page 5. For details, refer to the instructions
supplied with the MDX-E300 or KX-E300.
(Example)
BALANCE
INPUT
VOLUME
L
R
TREBLEBASS
PHONES
STANDBY/ON
TIMER
DISPLAY MEMORY
NATURAL SOUND
STEREO RECEIVER
RX–E600
AUTO/MAN'L
PRESET/BAND
TIMER HOUR MIN
MIN MAX
PRESET/TUNING
TIMER ADJ
+–+–
USING THE BUILT-IN TIMER
0107RXE600_CA_12-13_E.p65 2004.09.02, 14:3312
English
USING THE BUILT-IN TIMER
13
Sleep timer
The unit can be set to automatically place itself in standby
mode after a designated time.
1 Play the desired sound source.
2 Press SLEEP repeatedly until the desired sleep time
appears in the display. Each time you press SLEEP,
the sleep time changes as follows:
About 4 seconds after setting, the normal display will
resume.
• “SLEEP” will appear in the display.
3 The unit will turn off automatically when the selected
sleep time is reached.
SLEEP
SLEEP 2h00m
SLEEP 1h30m
SLEEP 1h00m
SLEEP 0h30m
SLEEP OFF
PRESET
TUNER
PRESET
MD TAPE
AUX
MD
REC
/
PAU SE
TAPE
REC
/
PAU SE
MODE
SLEEP
DISPLAY
DUBBING
VOLUME
START
DVD
USING THE BUILT-IN TIMER
0107RXE600_CA_12-13_E.p65 2004.09.02, 14:3313
SYSTEM CONTROL
14
Controlling other components
DVD-E600
1 Numeric buttons
• +100 button is used when operating
MDX-E300.
2 * (Pause)
3 # (Play)
4 & (Stop)
5 $ ! (Skip/Seach Backward)
6 ⁄ › (Skip/Seach Forward)
7 DVD input
POWER
1 2 3
123
4 5 6
456
7 8 9
78
0 +10 +100
REP
RANDOM
PROG
ABC
TIME
DE
TAPE
DIRECTION
PRESET
TUNER
PRESET
MD DVD TAPE
AUX
MD
REC
/
PAUSE
TAPE
REC
/
PAUSE
MODE
SLEEP
DISPLAY
DUBBING
VOLUME
START
1
22
3
4
56
7
0108RXE600_CA_14-16_E.p65 2004.09.02, 14:3414
SYSTEM CONTROL
15
English
MDX-E300
1 Numeric buttons
2 REP (Repeat)
3 RANDOM
4 * (Pause)
5 PROG (Program)
6 # (Play)
7 ⁄ › (Skip/Search Forward)
8 $ ! (Skip/Search Backward)
9 & (Stop)
0 MD input
q MD REC/PAUSE
KX-E300
1 # (Play)
2 ⁄ › (Fast-foward)
3 $ ! (Rewind)
4 & (Stop)
5 TAPE input
6 TAPE REC/PAUSE
POWER
1 2 3
123
4 5 6
456
7 8 9
78
0 +10 +100
REP
RANDOM
PROG
ABC
TIME
DE
TAPE
DIRECTION
PRESET
TUNER
PRESET
MD DVD TAPE
AUX
MD
REC
/
PAUSE
TAPE
REC
/
PAUSE
MODE
SLEEP
DISPLAY
DUBBING
VOLUME
START
1
25
6,1
3
4
9,4
8,3
7,2
50
q
6
0108RXE600_CA_14-16_E.p65 2004.09.02, 14:3415
SYSTEM CONTROL
16
• Recording automatically starts at the beginning of
the tape. (Pressing DUBBING START
automactially rewinds the tape to the beginning)
• Recording automatically starts at the beginning of
the tape. (Pressing DUBBING START
automactially rewinds the tape to the beginning)
2 Press DUBBING START to start recording.
Note
• The displays 1~4 which include the component you have
not connected to your receiver (RX-E600) will be skipped.
To stop dubbing
Press &.
Note
• If DVD playback stops or completes when you are using the
DVD player as a recording source, the recording component
records 10 additional seconds of silence.
Before recording
Follow the instructions as described in “Connecting the
system” on page 5 before using the MDX-E300 or KX-
E300 to record. For details, refer to the instructions
supplied with the MDX-E300 or KX-E300. Sources
connected to the AUX terminal can be recorded to tape or
MD.
Dubbing setting
There are six combinations of components. When you
select a mode, recording for mode starts and ends
automatically in a manner preset for that mode.
DUBBING
START
DUBBING
MODE
1
2
1 Select a component combination. Each time you
press DUBBING MODE, the mode changes in the
following order:
3
4
Record unitPlay unit
TAPE
DIRECTION
PRESET
TUNER
PRESET
MD
DVD
TAPE
AUX
MD
REC
/
PAU SE
TAPE
REC
/
PAUSE
MODE
SLEEP
DISPLAY
DUBBING
VOLUME
START
Record unitPlay unit
Sidan laddas ...
Sidan laddas ...
Sidan laddas ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
på andra språk
- italiano: Yamaha RX-E600 Manuale del proprietario
- čeština: Yamaha RX-E600 Návod k obsluze
- español: Yamaha RX-E600 El manual del propietario
- Deutsch: Yamaha RX-E600 Bedienungsanleitung
- polski: Yamaha RX-E600 Instrukcja obsługi
- português: Yamaha RX-E600 Manual do proprietário
- français: Yamaha RX-E600 Le manuel du propriétaire
- Türkçe: Yamaha RX-E600 El kitabı
- English: Yamaha RX-E600 Owner's manual
- dansk: Yamaha RX-E600 Brugervejledning
- русский: Yamaha RX-E600 Инструкция по применению
- suomi: Yamaha RX-E600 Omistajan opas
- Nederlands: Yamaha RX-E600 de handleiding
- română: Yamaha RX-E600 Manualul proprietarului