Blaupunkt Xtreme Plus Användarmanual

Kategori
Robotdammsugare
Typ
Användarmanual
BLUEBOT
XTREME PLUS
EN USER MANUAL 2
DA BRUGERVEJLEDNING 28
SW ANVÄNDARMANUAL 54
NO BRUKERMANUAL 80
ALL DISPOSAL & RECYCLING 106
Enjoy it.
2
Welcome!
Thank you for choosing the Blaupunkt Bluebot XTREME Plus.
With this manual we would like to support you in the set-up and usage of
your Blaupunkt Bluebot robot.
For extra how-to videos, tips & tricks, FAQs or contact details, go to:
www.blaupunktrobotics.eu/support
In this manual you will nd the following topics to support you in the
setup of your robot:
1 Safety regulations .......................................................................... 03
2 Product information ...................................................................... 05
3 Installation of the robot & auto station ...................................... 07
4 Installation of the Bluebot application .........................................10
5 Usage of the robot & auto station ................................................12
6 Cleaning settings ............................................................................14
7 Maintenance ...................................................................................15
8 Basic parameters ............................................................................23
9 Usage limitations ........................................................................... 24
10 Troubleshooting ............................................................................ 25
11 Warranty ......................................................................................... 27
FOREWORD
3
EN
1. SAFETY REGULATIONS
WARNING:
· Use only the original rechargeable battery and charging station specially equipped
by the manufacturer. Non-rechargeable batteries are strictly prohibited, please refer
to "product parameters" for battery specication information.
· It is forbidden to use the product in environments with open ames or fragile
objects.
· It is forbidden to use the product in extremely hot (above 40 °C) or extremely cold
(below 0 °C) environments.
· It is forbidden to use the products near burning or evenly hot object, for example a
burning replace.
· Do not use this product in high temperature environments.
· It is forbidden to approach the opening and operating parts of the robot with
ngers, clothes, hair and any item for safety reasons.It is forbidden to use the products
on wet or uneven ground.
· It is forbidden for the product to absorb any articles such as stones and waste paper
that may clog the product.
· It is forbidden for the product to absorb any inammable substances, such as
petrol, toner and toner for printers. Prohibit the use of products in clean areas with
ammable items.
· It is forbidden for the product to absorb any burning articles, such as cigarettes,
matches, ashes and other articles that may cause re.
· It is forbidden to place objects at the suction opening. Do not use the product when
the suction port is blocked. Clean all possible blockage at the suction opening to
ensure smooth air circulation at the suction opening.
· Use the power cord carefully to avoid damage. Its forbidden to use the power cord
to drag or pull the product and the product charging station. It’s forbidden to use the
power cord as a handle. Its forbidden to clamp the power cord in the crack of the
door. It is forbidden to pull the power cord at sharp corners.
· Do not use a damaged charging/auto station.
· Even if the product has been severely damaged, burning of the product is
prohibited, which may lead to explosion of the battery of the product.
GENERAL SAFETY REGULATIONS:
Before using this product, please read the following safety instructions and follow all routine safety precautions.
Please read the instructions carefully, please keep the instructions.
Any operation inconsistentcy with this instruction manual may cause damage to this product.
4
NOTE:
· Only authorized technicians can disassemble this product. Users are not
recommended to disassemble this product by themselves.
· This product can only use the power adapter provided by the factory. lf other
adapters are used, the product may be damaged.
· Do not touch wires, sockets or power adapters when your hands are wet.
· Make sure no fabrics or bigger items roll into the product drive wheels.
· Do not place this product near cigarette butts, lighters and other smoldering fires.
· Please clean the product after charging.
· Do not bend wires excessively or place heavy objects and sharp objects on the machine.
· This product is an indoor household product. Do not use it outdoors.
· Do not sit on the product.
· Do not use this product (e.g. bathroom) in a wet environment.
· Before using this product, please remove all vulnerable items (e.g. glasses, lamps,
etc.) on the ground as well as items (e.g. wires, paper sheets, curtains) that may
entangle the side brushes and air suction passages.
· Do not put this product in a place where it is easy to fall (e.g. on desks and chairs, by
the stair case).
· Please carefully check whether the power adapter is connected to the socket before
use, otherwise the battery may be damaged.
·To prevent tripping, please inform other members of the house when this product works.
· Please empty the dust bin before using this product when the dust bin is full.
· Please remove the battery from the machine before the product is scrapped.
· Please make sure that this product is not powered on when removing the battery.
· Please recycle the discarded batteries safely.
· Recommended to block the staircase exit or areas where the robot may fall. The anti-
drop sensors prevent the robot from tumbling down stars and steep drops. However,
they may work less effectively when dirty or used on reflective/very dark-colored floors.
· To clean and maintain the robot and the auto station, you must turn off both. Pull
out the power cord from the socket and disconnect the power supply first.
· Do not immerse the robot or the auto station in water for cleaning or rinse them with water.
· Do not whipe any part of the product with a damp cloth or any liquid.
· Do not use the mopping module on the carpet.
SAFETY REGULATIONS
5
EN
2. PRODUCT INFORMATION
XTREME Plus robot Auto station for dust
collection and charging
Instruction manual Side Brush
(4x / 2 pairs)
Mop cloth support Cleaning brush
with knife
Mop (2x)
HEPA lter n°12 +
Sponge lter
(1 installed + 1 extra)
Dust bag 3L (2x) 2-in-1 combi watertank 210 ml
dustbin 230 ml
(installed)
Main Brush
(installed)
Main brush cover
(installed)
Remote control Battery (x2)
6
PRODUCT INFORMATION
Filter cover
Anti-collision,
Infrared recharging
sensors
Wall sensor
System reset button
System upgrade port
for professional use
Mop cloth
assembly
Main brush
Main brush
cover
Side wheel
Side wheel
Battery
Cli sensor
Universal
wheel
Side brush
Cli sensor
TOP & FRONT BOTTOM
REMOTE CONTROL
Dustbin button
Infrared lens
Suction inlet
Charging / Dust
collection indicator
Dustbag chamber
Wind ow
Charging jack
Charging and dust
collection sensor
Upper cover
Open the upper cover,
Install/remove dust bag.
Anti-collision sensor for radar
LDS laser ranging sensor
CLEANING ON &OFF
• Short press to start clean/pause
• Long press for 3secs for on/o
CHARGING/LOCAL CLEANING
• Short press charge/pause
• Long press to start local cleaning
INDICATOR LIGHT
• Blue: normal operation or charging
• Red: abnormal condition or low battery
• Purple: robot is not connected to the network
RESET WIFI
• Press the two buttons simultaneously for 3secs
Auto cleaning start/pause
Go forward
Turn left
Adjustment of suction power
Dnd mode on/o
Edge cleaning
Charging start/pause
Turn right
Find robot
Adjust water ow
Spot cleaning start/pause
7
EN
Place against the wall
3. INSTALLATION OF THE ROBOT & AUTO STATION
AUTO STATION
1 Lay the auto station on the at ground over 5cm away from the wall, insert
the power plug into the socket, meeting the requirements, and connect the
power supply.
2 Ensure that there are no obstacles within 1.5m in front of the auto station
and 0.5m on both sides.
1.5m
0.5m
0.5m
8
PRODUCT ASSEMBLY
1 Install the brushes. Make the left side-brush (L) and the right-
side brush (R) correspond to L and R on the bottom casing,
keep pressing the side brushes.
They are installed when you hear a click” sound.
2 Place the 2-in-1 combi watertank in the robot.
3 Fully charge the robot (before 1st time use)
4 Connect with Bluebot app (optional)
5 Start cleaning
NOTE
• Please do not move the auto station without reason and keep it
out of direct sunlight.
• If the auto station is relocated, the robot may fail in positioning
and lose the map. When restarted, the robot will rebuild and
memorise the map. In the rebuilt map the cleaning information for
forbidden areas and other areas may have been lost.
• Direct sunlight will interfere with the recharging signal and
consequently, the robot may be unable to return to the charging/
auto station.
• The robot cannot be used to remove liquids.
• If the battery level is less than 20% the machine will not work.
Please charge it.
• The machine will return to the auto station automatically if the
battery level is less than 20% when in use and will be powered
o and then start cleaning automatically after the battery level
reaches 80%.
• Please clear various wires (including the power line of the auto
station
) from the ground before use to avoid outage and damage
of objects or wires when wires are dragged by the robot.
INSTALLATION OF THE ROBOT & AUTO STATION
9
EN
INSTALLATION OF THE ROBOT & AUTO STATION
INSTALLATION OF MOPPING MODULE
1 Paste the mopping cloth at onto the bottom of the water
tank.
2 Fill the water tank: uncap the cover and ll with water.
3 Press and hold the button in the middle of the tank and
push it horizontally along the rear of the robot. The module is
correctly in place if you hear the sound of a click".
4 Remove the mopping module
When the robot is nished working, press the button in
the middle of water tank to remove the mopping module
backwards, empty the water in the water tank and clean the
mopping cloth (do not move or turn the robot over during
cleaning).
NOTES FOR MOPPING MODULE
· Please do not use the mopping module after it has been left unused.
· For safety reasons, please be sure to remove the mopping module when it is being
charged or left unused.
· Please do not mop the carpet. Set a forbidden area in the Bluebot app to prevent the
machine from going onto the carpet.
· To a ch ieve a b etter mo pping e ect, the mopping module should be installed after
take out and reassemble the mopping module according to step 3. Please do not
move or turn the robot over, otherwise, it could fail in its positioning, lose its map and
“forget” the forbidden areas that are programmed.
· The mopping function of the machine is intended for wiping and is not conducive
to deep cleaning. It cannot remove intractable stains eectively and replace the
labour force.
· Please don't use any detergent in the watertank to prevent clogging.
· The robot cannot be used to remove liquids.
10
BLUEBOT APPLICATION 1 Fully charge robot 2 Download Bluebot app 3 Steps for registration 4 Connect robot with app (steps)
4. INSTALLATION BLUEBOT APP
Place the robot in the charging station to charge and
make sure it’s fully charged before use. Remove the robot from the charging station. Make sure the Robot is on, by holding in the ‘On button’
for a few seconds on top of the robot. Wait until the robot
has started fully.
Register a new account if
you are not yet an existing
user.
Open the Bluebot app and
press the ‘+ icon’ to add your
device.
1 2 3
4 5 6
Download the Bluebot app. The app can be found in the
Appstore and Google Play.
11
EN
INSTALLATION BLUEBOT APP
Go to connect
enter the password and
Press on the 'Go to
connect' button in the
bottom of your screen.
After your registration, make sure the robot is
removed from it's charging station. Turn on your
Robot by pressing the 'On button' . After that is
done, press both the 'Home button' and 'On
button' simultaneously for more than 3 seconds
connection.
Select the 'SmartLife
xxx' network from the
list and return to the
Bluebot app.
Your robot will now
connect to the App.
7 8
9
11 12
Select the
BLUEBOT XTREME PLUS
(2.4+5GHZ)
10
Tick ‘Make sure the purple
light blinks slowly’ when
applicable and press ‘Next’
12
5. USAGE OF THE ROBOT & AUTO STATION
REMOVE THE LIMIT BAR
Put the robot on the flat indoor ground, and remove the protection device
of the limit bar at both ends of the front bumper.
CHARGING OF THE ROBOT
Press and hold the button for 3 seconds to start the robot, and then
short-press the button to make the robot recharge automatically. The
robot is ready once fully charged.
• Fully charge the robot before starting cleaning.
• Before starting the cleaning, tidy away the wires and articles on the
ground to avoid damage caused by winding, dragging and hitting during
cleaning.
• It is suggested to start the robot at the auto station.
When the battery is low during the cleaning, the robot will automatically
return to the auto station for charging, and automatically return to the
interrupted place to continue cleaning when the battery is full.
0.5m
0.5m
1.5m
13
EN
CLEANING MODE
After the robot is powered on, it will scan and generate the map and divide
it into areas intelligently. Then sweep the areas one by one along the wall
orderly, efficiently and thoroughly and plan the cleaning route in a bow/S
shape. The robot will return to the charging station automatically after
cleaning.
NOTE
Do not move the robot casually and frequently when it is cleaning. After
moving, please put the robot near the original position. When it starts again,
it will try to reposition itself. After successful positioning, it would follow the
planned path and continue to work. If the positioning fails, the robot would
abort previous mission, make a map and do the cleaning again.
SPOT CLEANING
When a local area needs a deep sweep, the user specifies a point on the
map on the APP, the machine will automatically drive to the vicinity of the
point, take the point as the center, and clean within 1.5m x 1.5m.
PARTIAL CLEANING
When the robot cannot be controlled by the mobile APP, please remove
the robot to the place you want to clean. Long press the button for 3
seconds, and the robot will clean twice within the scope of 2mx2m
centering on itself.
Area being cleaned
Area to be cleaned
2m
2m
USAGE OF THE ROBOT & AUTO STATION
14
MORE OPTIONS
Timer*
Set a timer to program the robot to clean at a certain time or day.
Manual
Control the robot manually with the remote control or use the Bluebot app
on your phone as a remote control.
Find robot
Tap this button when you lost your robot and your robot will tell you where
it is.
Map management*
Use this function to manage your maps (5 max.).
Water regulation
Control the water regulation and choose “Low”, “Medium or “High. This will
regulate how wet the mop will become when using the robot including
the 2 in 1 electric- controlled water tank.
Auto Boost*
Auto Boost will increase suction power when the robot gets more friction.
This is designed to increase suction on carpets.
Custom mode*
So the robot can remember per area what route to use for cleaning.
Record*
View all your previous vacuum cleaning records. You can see how many m2
has been cleaned and the time it took. Here you can also load previously
saved maps. Ideal when cleaning different areas (upper floor for instance).
Voice and volume
Setup your language and change the volume.
Do not disturb mode
Here you can schedule an do not disturb time period.
Consumables and maintenance*
Here you will find an overview of consumables and indicates when
consumables need to be replaced or maintenance is required.
More info*
Here you will find network and robot information
Set wall / Resctricted Area*
Use this function to create no-go zones within the area that you are
cleaning. You can draw virtual walls that blocks the robot from crossing. Or
you create a restricted area for either vacuuming or mopping.
* Via Bluebot app only
6. CLEANING SETTINGS
15
EN
REPLACE THE DUST BAG
When the dust bag is full, please replace the dust bag in time.
7. MAINTENANCE
Open the
upper cover
Close the
upper cover
Make sure that the
dustbag is installed
in place
Correct installation
Place a new dust bag
Pull up the lifting
handle of the dust
bag and take out
the dust bag
Throw away the
used dust bag
16
CLEAN THE INFRARED LENS/CHARGING AND DUST
COLLECTION SENSOR HEAD
Wipe them gently with a clean, soft, dry cloth. It is recommended to clean
them once a month.
CLEAN THE FILTER SCREEN OF THE FAN
The lter screen of the fan is below the dust bag. If there is dust
accumulation, wipe it gently with a clean, soft, dry cloth.
It is recommended to clean them once a month.
MAINTENANCE
Infrared lens
Fan lter
screen
Charging and dust collection
sensor head
17
EN
CLEAN THE MAIN BRUSH
The main brush is a consumable item and should be cleaned at least once
a week. It is recommended to replace the main brush every 6-12 months to
ensure the cleaning eect.
1 Reverse the robot, press the snap on the main brush cover, and remove
the main brush cover and the main brush.
NOTE Be careful when reversing the robot to prevent damage to the lidar laser.
2 Cut o the hair twisted around on the main brush with the cleaning
knife, and then clean the main brush with the cleaning brush with the
other end of the cleaning knife.
3 Reinstall the main brush and the main brush cover.
Press and fasten the snap.
MAINTENANCE
Main brush
cover
Main brush
18
CLEAN/REPLACE THE SIDE BRUSH
1 Turn over the machine and pull the side brush out and upwards
2 Remove hair and dirt and reassemble the side brush.
3 Make the left-side brush (L) and the right-side brush (R) correspond to L
and R on the bottom casting, press L and R to reinstall them.
CLEAN THE SENSORS
Clean the sensors with a soft, dry mop, including:
1 Three anti-dropping sensors at the bottom of the robot.
2 Electric shock protector and the pins to connect with the charging
station at the bottom of the robot (please cut the power o during
cleaning)
3 Signal transmission area of charging/auto station.
MAINTENANCE
Anti-drop sensor
Charging contact points
TOF sensor
LDS Laser ranging
sensor
Anti-colision sensor
for radar
Anti-colision sensor
Infrared recharging
sensor
19
EN
Auto Station:
Infrared lens X2
Charging and dust collection sensor plates X2
BATTERY
· The robot is furnished with high-performance lithium-ion batteries.
· To mai nta in bat ter y per fo rma nce, plea se kee p t he rob ot cha rge d i n d aily us e
· If the machine is left unused for any length of time, please shut down and
keep it properly.
· Charge it at least every three months to avoid damaging batteries due to
excessive discharge.
FIRMWARE UPGRADE
· Upgrade rmware using the Bluebot app. If new rmware is detected,
upgrade it according to the report.
· The battery level should be 50% during rmware upgrade, so if needed the
machine should be placed on the charging/ auto station to charge before the
rmware upgrade takes place.
· Power failure restart. When the button is not responding or can not be
turned o, reset the button with the pin length for one second, and the
robot will restart the power.
MAINTENANCE
Infrared lens
Charging and dust collection
sensor plates
20
MAINTENANCE
Clean the 2in1 water tank
1 Press and hold the release button of the two-in-one water tank
and at the same time pull it outwards.
2 Open the dustbin by pressing the dustbin snap.
3 Remove the lter screen clip.
Dustbin
Water tank cover/
water injection port
Dustbin snap
Release button of 2in1 water tank
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107

Blaupunkt Xtreme Plus Användarmanual

Kategori
Robotdammsugare
Typ
Användarmanual