Blaupunkt Xtreme Plus Användarmanual

BLUEBOT

XTREME PLUS

EN USER MANUAL 2

DA BRUGERVEJLEDNING 28

SW ANVÄNDARMANUAL 54

NO BRUKERMANUAL 80

ALL DISPOSAL & RECYCLING 106

Enjoy it.

2

Welcome!

Thank you for choosing the Blaupunkt Bluebot XTREME Plus.

With this manual we would like to support you in the set-up and usage of

your Blaupunkt Bluebot robot.

For extra how-to videos, tips & tricks, FAQs or contact details, go to:

www.blaupunktrobotics.eu/support

In this manual you will nd the following topics to support you in the

setup of your robot:

1 Safety regulations .......................................................................... 03

2 Product information ...................................................................... 05

3 Installation of the robot & auto station ...................................... 07

4 Installation of the Bluebot application .........................................10

5 Usage of the robot & auto station ................................................12

6 Cleaning settings ............................................................................14

7 Maintenance ...................................................................................15

8 Basic parameters ............................................................................23

9 Usage limitations ........................................................................... 24

10 Troubleshooting ............................................................................ 25

11 Warranty ......................................................................................... 27

FOREWORD

3

EN

1. SAFETY REGULATIONS

WARNING:

· Use only the original rechargeable battery and charging station specially equipped

by the manufacturer. Non-rechargeable batteries are strictly prohibited, please refer

to "product parameters" for battery specication information.

· It is forbidden to use the product in environments with open ames or fragile

objects.

· It is forbidden to use the product in extremely hot (above 40 °C) or extremely cold

(below 0 °C) environments.

· It is forbidden to use the products near burning or evenly hot object, for example a

burning replace.

· Do not use this product in high temperature environments.

· It is forbidden to approach the opening and operating parts of the robot with

ngers, clothes, hair and any item for safety reasons.It is forbidden to use the products

on wet or uneven ground.

· It is forbidden for the product to absorb any articles such as stones and waste paper

that may clog the product.

· It is forbidden for the product to absorb any inammable substances, such as

petrol, toner and toner for printers. Prohibit the use of products in clean areas with

ammable items.

· It is forbidden for the product to absorb any burning articles, such as cigarettes,

matches, ashes and other articles that may cause re.

· It is forbidden to place objects at the suction opening. Do not use the product when

the suction port is blocked. Clean all possible blockage at the suction opening to

ensure smooth air circulation at the suction opening.

· Use the power cord carefully to avoid damage. It’s forbidden to use the power cord

to drag or pull the product and the product charging station. It’s forbidden to use the

power cord as a handle. It’s forbidden to clamp the power cord in the crack of the

door. It is forbidden to pull the power cord at sharp corners.

· Do not use a damaged charging/auto station.

· Even if the product has been severely damaged, burning of the product is

prohibited, which may lead to explosion of the battery of the product.

GENERAL SAFETY REGULATIONS:

Before using this product, please read the following safety instructions and follow all routine safety precautions.

Please read the instructions carefully, please keep the instructions.

Any operation inconsistentcy with this instruction manual may cause damage to this product.

4

NOTE:

· Only authorized technicians can disassemble this product. Users are not

recommended to disassemble this product by themselves.

· This product can only use the power adapter provided by the factory. lf other

adapters are used, the product may be damaged.

· Do not touch wires, sockets or power adapters when your hands are wet.

· Make sure no fabrics or bigger items roll into the product drive wheels.

· Do not place this product near cigarette butts, lighters and other smoldering fires.

· Please clean the product after charging.

· Do not bend wires excessively or place heavy objects and sharp objects on the machine.

· This product is an indoor household product. Do not use it outdoors.

· Do not sit on the product.

· Do not use this product (e.g. bathroom) in a wet environment.

· Before using this product, please remove all vulnerable items (e.g. glasses, lamps,

etc.) on the ground as well as items (e.g. wires, paper sheets, curtains) that may

entangle the side brushes and air suction passages.

· Do not put this product in a place where it is easy to fall (e.g. on desks and chairs, by

the stair case).

· Please carefully check whether the power adapter is connected to the socket before

use, otherwise the battery may be damaged.

·To prevent tripping, please inform other members of the house when this product works.

· Please empty the dust bin before using this product when the dust bin is full.

· Please remove the battery from the machine before the product is scrapped.

· Please make sure that this product is not powered on when removing the battery.

· Please recycle the discarded batteries safely.

· Recommended to block the staircase exit or areas where the robot may fall. The anti-

drop sensors prevent the robot from tumbling down stars and steep drops. However,

they may work less effectively when dirty or used on reflective/very dark-colored floors.

· To clean and maintain the robot and the auto station, you must turn off both. Pull

out the power cord from the socket and disconnect the power supply first.

· Do not immerse the robot or the auto station in water for cleaning or rinse them with water.

· Do not whipe any part of the product with a damp cloth or any liquid.

· Do not use the mopping module on the carpet.

SAFETY REGULATIONS

5

EN

2. PRODUCT INFORMATION

XTREME Plus robot Auto station for dust

collection and charging

Instruction manual Side Brush

(4x / 2 pairs)

Mop cloth support Cleaning brush

with knife

Mop (2x)

HEPA lter n°12 +

Sponge lter

(1 installed + 1 extra)

Dust bag 3L (2x) 2-in-1 combi watertank 210 ml

dustbin 230 ml

(installed)

Main Brush

(installed)

Main brush cover

(installed)

Remote control Battery (x2)

6

PRODUCT INFORMATION

Filter cover

Anti-collision,

Infrared recharging

sensors

Wall sensor

System reset button

System upgrade port

for professional use

Mop cloth

assembly

Main brush

cover

Side wheel

Battery

Cli sensor

Universal

wheel

Side brush

Cli sensor

TOP & FRONT BOTTOM

REMOTE CONTROL

Dustbin button

Infrared lens

Suction inlet

Charging / Dust

collection indicator

Dustbag chamber

Wind ow

Charging jack

Charging and dust

collection sensor

Upper cover

Open the upper cover,

Install/remove dust bag.

Anti-collision sensor for radar

LDS laser ranging sensor

CLEANING ON &OFF

• Short press to start clean/pause

• Long press for 3secs for on/o

CHARGING/LOCAL CLEANING

• Short press charge/pause

• Long press to start local cleaning

INDICATOR LIGHT

• Blue: normal operation or charging

• Red: abnormal condition or low battery

• Purple: robot is not connected to the network

RESET WIFI

• Press the two buttons simultaneously for 3secs

Auto cleaning start/pause

Go forward

Turn left

Adjustment of suction power

Dnd mode on/o

Edge cleaning

Charging start/pause

Turn right

Find robot

Adjust water ow

Spot cleaning start/pause

7

EN

Place against the wall

3. INSTALLATION OF THE ROBOT & AUTO STATION

AUTO STATION

1 Lay the auto station on the at ground over 5cm away from the wall, insert

the power plug into the socket, meeting the requirements, and connect the

power supply.

2 Ensure that there are no obstacles within 1.5m in front of the auto station

and 0.5m on both sides.

1.5m

0.5m

8

PRODUCT ASSEMBLY

1 Install the brushes. Make the left side-brush (L) and the right-

side brush (R) correspond to L and R on the bottom casing,

keep pressing the side brushes.

They are installed when you hear a “click” sound.

2 Place the 2-in-1 combi watertank in the robot.

3 Fully charge the robot (before 1st time use)

4 Connect with Bluebot app (optional)

5 Start cleaning

NOTE

• Please do not move the auto station without reason and keep it

out of direct sunlight.

• If the auto station is relocated, the robot may fail in positioning

and lose the map. When restarted, the robot will rebuild and

memorise the map. In the rebuilt map the cleaning information for

forbidden areas and other areas may have been lost.

• Direct sunlight will interfere with the recharging signal and

consequently, the robot may be unable to return to the charging/

auto station.

• The robot cannot be used to remove liquids.

• If the battery level is less than 20% the machine will not work.

Please charge it.

• The machine will return to the auto station automatically if the

battery level is less than 20% when in use and will be powered

o and then start cleaning automatically after the battery level

reaches 80%.

• Please clear various wires (including the power line of the auto

station

) from the ground before use to avoid outage and damage

of objects or wires when wires are dragged by the robot.

INSTALLATION OF THE ROBOT & AUTO STATION

9

EN

INSTALLATION OF THE ROBOT & AUTO STATION

INSTALLATION OF MOPPING MODULE

1 Paste the mopping cloth at onto the bottom of the water

tank.

2 Fill the water tank: uncap the cover and ll with water.

3 Press and hold the button in the middle of the tank and

push it horizontally along the rear of the robot. The module is

correctly in place if you hear the sound of a “click".

4 Remove the mopping module

When the robot is nished working, press the button in

the middle of water tank to remove the mopping module

backwards, empty the water in the water tank and clean the

mopping cloth (do not move or turn the robot over during

cleaning).

NOTES FOR MOPPING MODULE

· Please do not use the mopping module after it has been left unused.

· For safety reasons, please be sure to remove the mopping module when it is being

charged or left unused.

· Please do not mop the carpet. Set a forbidden area in the Bluebot app to prevent the

machine from going onto the carpet.

· To a ch ieve a b etter mo pping e ect, the mopping module should be installed after

take out and reassemble the mopping module according to step 3. Please do not

move or turn the robot over, otherwise, it could fail in its positioning, lose its map and

“forget” the forbidden areas that are programmed.

· The mopping function of the machine is intended for wiping and is not conducive

to deep cleaning. It cannot remove intractable stains eectively and replace the

labour force.

· Please don't use any detergent in the watertank to prevent clogging.

· The robot cannot be used to remove liquids.

10

BLUEBOT APPLICATION 1 Fully charge robot 2 Download Bluebot app 3 Steps for registration 4 Connect robot with app (steps)

4. INSTALLATION BLUEBOT APP

Place the robot in the charging station to charge and

make sure it’s fully charged before use. Remove the robot from the charging station. Make sure the Robot is on, by holding in the ‘On button’

for a few seconds on top of the robot. Wait until the robot

has started fully.

Register a new account if

you are not yet an existing

user.

Open the Bluebot app and

press the ‘+ icon’ to add your

device.

1 2 3

4 5 6

Download the Bluebot app. The app can be found in the

Appstore and Google Play.

11

EN

INSTALLATION BLUEBOT APP

Go to connect

enter the password and

Press on the 'Go to

connect' button in the

bottom of your screen.

After your registration, make sure the robot is

removed from it's charging station. Turn on your

Robot by pressing the 'On button' . After that is

done, press both the 'Home button' and 'On

button' simultaneously for more than 3 seconds

connection.

Select the 'SmartLife

xxx' network from the

list and return to the

Bluebot app.

Your robot will now

connect to the App.

7 8

9

11 12

Select the

BLUEBOT XTREME PLUS

(2.4+5GHZ)

10

Tick ‘Make sure the purple

light blinks slowly’ when

applicable and press ‘Next’

12

5. USAGE OF THE ROBOT & AUTO STATION

REMOVE THE LIMIT BAR

Put the robot on the flat indoor ground, and remove the protection device

of the limit bar at both ends of the front bumper.

CHARGING OF THE ROBOT

Press and hold the button for 3 seconds to start the robot, and then

short-press the button to make the robot recharge automatically. The

robot is ready once fully charged.

• Fully charge the robot before starting cleaning.

• Before starting the cleaning, tidy away the wires and articles on the

ground to avoid damage caused by winding, dragging and hitting during

cleaning.

• It is suggested to start the robot at the auto station.

• When the battery is low during the cleaning, the robot will automatically

return to the auto station for charging, and automatically return to the

interrupted place to continue cleaning when the battery is full.

0.5m

1.5m

13

EN

CLEANING MODE

After the robot is powered on, it will scan and generate the map and divide

it into areas intelligently. Then sweep the areas one by one along the wall

orderly, efficiently and thoroughly and plan the cleaning route in a bow/S

shape. The robot will return to the charging station automatically after

cleaning.

NOTE

Do not move the robot casually and frequently when it is cleaning. After

moving, please put the robot near the original position. When it starts again,

it will try to reposition itself. After successful positioning, it would follow the

planned path and continue to work. If the positioning fails, the robot would

abort previous mission, make a map and do the cleaning again.

SPOT CLEANING

When a local area needs a deep sweep, the user specifies a point on the

map on the APP, the machine will automatically drive to the vicinity of the

point, take the point as the center, and clean within 1.5m x 1.5m.

PARTIAL CLEANING

When the robot cannot be controlled by the mobile APP, please remove

the robot to the place you want to clean. Long press the button for 3

seconds, and the robot will clean twice within the scope of 2mx2m

centering on itself.

Area being cleaned

Area to be cleaned

2m

USAGE OF THE ROBOT & AUTO STATION

14

MORE OPTIONS

Timer*

Set a timer to program the robot to clean at a certain time or day.

Manual

Control the robot manually with the remote control or use the Bluebot app

on your phone as a remote control.

Find robot

Tap this button when you lost your robot and your robot will tell you where

it is.

Map management*

Use this function to manage your maps (5 max.).

Water regulation

Control the water regulation and choose “Low”, “Medium” or “High”. This will

regulate how wet the mop will become when using the robot including

the 2 in 1 electric- controlled water tank.

Auto Boost*

Auto Boost will increase suction power when the robot gets more friction.

This is designed to increase suction on carpets.

Custom mode*

So the robot can remember per area what route to use for cleaning.

Record*

View all your previous vacuum cleaning records. You can see how many m2

has been cleaned and the time it took. Here you can also load previously

saved maps. Ideal when cleaning different area’s (upper floor for instance).

Voice and volume

Setup your language and change the volume.

Do not disturb mode

Here you can schedule an do not disturb time period.

Consumables and maintenance*

Here you will find an overview of consumables and indicates when

consumables need to be replaced or maintenance is required.

More info*

Here you will find network and robot information

Set wall / Resctricted Area*

Use this function to create no-go zones within the area that you are

cleaning. You can draw virtual walls that blocks the robot from crossing. Or

you create a restricted area for either vacuuming or mopping.

* Via Bluebot app only

6. CLEANING SETTINGS

15

EN

REPLACE THE DUST BAG

When the dust bag is full, please replace the dust bag in time.

7. MAINTENANCE

Open the

upper cover

Close the

upper cover

Make sure that the

dustbag is installed

in place

Correct installation

Place a new dust bag

Pull up the lifting

handle of the dust

bag and take out

the dust bag

Throw away the

used dust bag

16

CLEAN THE INFRARED LENS/CHARGING AND DUST

COLLECTION SENSOR HEAD

Wipe them gently with a clean, soft, dry cloth. It is recommended to clean

them once a month.

CLEAN THE FILTER SCREEN OF THE FAN

The lter screen of the fan is below the dust bag. If there is dust

accumulation, wipe it gently with a clean, soft, dry cloth.

It is recommended to clean them once a month.

MAINTENANCE

Infrared lens

Fan lter

screen

Charging and dust collection

sensor head

17

EN

CLEAN THE MAIN BRUSH

The main brush is a consumable item and should be cleaned at least once

a week. It is recommended to replace the main brush every 6-12 months to

ensure the cleaning eect.

1 Reverse the robot, press the snap on the main brush cover, and remove

the main brush cover and the main brush.

NOTE Be careful when reversing the robot to prevent damage to the lidar laser.

2 Cut o the hair twisted around on the main brush with the cleaning

knife, and then clean the main brush with the cleaning brush with the

other end of the cleaning knife.

3 Reinstall the main brush and the main brush cover.

Press and fasten the snap.

MAINTENANCE

Main brush

cover

Main brush

18

CLEAN/REPLACE THE SIDE BRUSH

1 Turn over the machine and pull the side brush out and upwards

2 Remove hair and dirt and reassemble the side brush.

3 Make the left-side brush (L) and the right-side brush (R) correspond to L

and R on the bottom casting, press L and R to reinstall them.

CLEAN THE SENSORS

Clean the sensors with a soft, dry mop, including:

1 Three anti-dropping sensors at the bottom of the robot.

2 Electric shock protector and the pins to connect with the charging

station at the bottom of the robot (please cut the power o during

cleaning)

3 Signal transmission area of charging/auto station.

MAINTENANCE

Anti-drop sensor

Charging contact points

TOF sensor

LDS Laser ranging

sensor

Anti-colision sensor

for radar

Anti-colision sensor

Infrared recharging

sensor

19

EN

Auto Station:

Infrared lens X2

Charging and dust collection sensor plates X2

BATTERY

· The robot is furnished with high-performance lithium-ion batteries.

· To mai nta in bat ter y per fo rma nce, plea se kee p t he rob ot cha rge d i n d aily us e

· If the machine is left unused for any length of time, please shut down and

keep it properly.

· Charge it at least every three months to avoid damaging batteries due to

excessive discharge.

FIRMWARE UPGRADE

· Upgrade rmware using the Bluebot app. If new rmware is detected,

upgrade it according to the report.

· The battery level should be ≥ 50% during rmware upgrade, so if needed the

machine should be placed on the charging/ auto station to charge before the

rmware upgrade takes place.

· Power failure restart. When the button is not responding or can not be

turned o, reset the button with the pin length for one second, and the

robot will restart the power.

MAINTENANCE

Infrared lens

Charging and dust collection

sensor plates

20

MAINTENANCE

Clean the 2in1 water tank

1 Press and hold the release button of the two-in-one water tank

and at the same time pull it outwards.

2 Open the dustbin by pressing the dustbin snap.

3 Remove the lter screen clip.

Dustbin

Water tank cover/

water injection port

Dustbin snap

Release button of 2in1 water tank

Sidan laddas ...

Blaupunkt Xtreme Plus Användarmanual

Blaupunkt Xtreme Plus Användarmanual

på andra språk

Andra dokument