ONKYO LS7200 - 3D SOUNDBAR SYSTEM Bruksanvisning

3D SOUNDBAR SYSTEM

LS7200

> Before Start > Part Names > Install > Initial Setup > Playback

Advanced Setup | Firmware Update | Others

Instruction Manual

Mode d’emploi

Manual de instrucciones

Manuale di istruzioni

Bedienungsanleitung

Gebruikershandleiding

Grundläggande bruksanvisning

2

> Before Start > Part Names > Install > Initial Setup > Playback

Advanced Setup | Firmware Update | Others

E

N

Before Start

Contents

Before Start

What's in the box ...............................................................................................3

Part Names

Main Unit (Front Panel) .....................................................................................5

Main Unit (Rear Panel) .....................................................................................6

Remote Controller .............................................................................................7

Main Unit (Display) ............................................................................................8

Sound Bar .........................................................................................................9

Subwoofer .......................................................................................................10

Install

1. Connect the Speakers ................................................................................. 11

2. Connect the TV ...........................................................................................13

3. Connect the HDMI AV Components ............................................................14

4. Connect the Audio Components .................................................................15

5. Connect Other Cables ................................................................................16

Initial Setup

Initial Setup with Auto Start-up Wizard ............................................................17

Playback

AV Component Playback ................................................................................19

Internet Radio .................................................................................................20

Spotify ............................................................................................................. 21

Music Server ...................................................................................................22

USB Storage Device .......................................................................................24

AirPlay

®

...........................................................................................................26

BLUETOOTH

®

Playback ................................................................................27

Listening to the FM Radio ...............................................................................28

Listening Modes ..............................................................................................30

Quick Menu .....................................................................................................38

Other Functions ..............................................................................................40

Advanced Setup

Setup Menu......................................................................................................41

Firmware Update

Firmware Update .............................................................................................53

Others

Troubleshooting ...............................................................................................56

General Specifications ....................................................................................61

About HDMI .....................................................................................................63

License and Trademark Information ................................................................64

3

> Before Start > Part Names > Install > Initial Setup > Playback

Advanced Setup | Firmware Update | Others

E

N

What's in the box

Network AV Receiver (Main unit/HT-L05) (1)

Sound bar (LB-403) (1)

Subwoofer (SLW-403) (1)

Remote controller (RC-941S) (1), batteries (AAA/R03) (2)

Speaker setup microphone (1)

Indoor FM antenna (1)

Sound bar connection cable (1)

Power cord (for subwoofer) (1)

Non-skid pads (4)

4

> Before Start > Part Names > Install > Initial Setup > Playback

Advanced Setup | Firmware Update | Others

E

N

0

The power cord must be connected only after all other cable connections are completed.

0 We will not accept responsibility for damage arising from the connection of equipment

manufactured by other companies.

0 Functionality may be introduced by firmware updates and service providers may cease

services, meaning that some network services and content may become unavailable in

the future. Furthermore, available services may vary depending on your area of

residence.

0 Specifications and appearance are subject to change without prior notice.

0 Quick Start Guide (1)

This document is an online instruction manual. It is not included as an accessory.

> Before Start >Part Names > Install > Initial Setup > Playback

Advanced Setup | Firmware Update | Others

5

E

N

Part Names

Main Unit (Front Panel)

1. Í ON/STANDBY button: Turns the unit on or into standby mode.

2. HYBRID STANDBY indicator: Lights if the unit enters standby mode when the features

are enabled that continue to work when this unit is in standby, such as HDMI Standby

Through (ÄP48) and Network Standby (ÄP51).

3. Display (ÄP8)

4. Remote control sensor

5. Volume dial: Allows you to adjust the volume.

6. USB port: A USB storage device is connected so that music files stored in it can be

played. You can also supply power (maximum 5 V/1 A) to USB devices with a USB cable.

7. PHONES jack: Stereo headphones with a mini plug ( 3.5 mm) are connected.

8. INPUT button: Switches the input to be played. (BD/DVD / CBL/SAT / GAME / STRM

BOX / CD / TV / FM / NET / USB / BLUETOOTH)

9. LISTENING MODE button: Allows you to select the listening mode. (ÄP30)

10.

TUNING43buttons: Select the frequency of FM radio stations.

  

    



6

> Before Start >Part Names > Install > Initial Setup > Playback

Advanced Setup | Firmware Update | Others

E

N

Main Unit (Rear Panel)

1. TUNER FM 75 jack: Connect the supplied antenna.

2. Wireless antenna: Raise for Wi-Fi connection or when using a BLUETOOTH enabled

device. The diagram shows the movable range for the wireless antenna. Do not try to

force it beyond this range otherwise you may break it.

3. AUDIO IN jacks: Input AV component audio signals with an analog audio cable.

4. DIGITAL IN OPTICAL jack: Input digital audio signals from a TV, for example, with a digital

optical cable.

5. SETUP MIC jack: The supplied speaker setup microphone is connected.

6. Power cord

7. ETHERNET port: Connect to the network with an Ethernet cable.

8. HDMI OUT jack: Connect a HDMI cable to transfer video signals and audio signals to a

TV.

9. HDMI IN jacks: Input video signals and audio signals with a HDMI cable connected to an

AV component.

10.

SPEAKERS terminal: Connect the included sound bar using the included sound bar

connection cable.

180°

90°













 







> Before Start >Part Names > Install > Initial Setup > Playback

Advanced Setup | Firmware Update | Others

7

E

N

Remote Controller

1. Í button: Turns the unit on or into standby mode.

2. Input selector buttons: Switches the input to be played.

3. Q (QUICK MENU) button: You can perform common settings on the TV screen. (ÄP38)

4. Cursors, ENTER button: Select the item with the cursors and press ENTER to confirm.

5. button: Displays the Setup menu.

(

Ä

P41)

6. Volume buttons: Allows you to adjust the volume. This button also cancels the muting.

7. button: Temporarily mutes audio. Press again to cancel muting.

8. Listening mode buttons: Allows you to select the listening mode. (ÄP30)

9. Play buttons: You can start play of the Music Server or USB.

10.

button: You can start repeat or random play of the Music Server or USB.

CLEAR button: Deletes all characters you have entered when entering text on the TV

screen.

11.

DIALOG button: Switches the Dialog Enhancement setting.

(

Ä

P39)

12.

DIMMER button: You can adjust the brightness of the display in three steps. It cannot be

turned off completely.

13.

button: Switches the information on the display.

14.

button: Returns the display to the previous state during setting.

15.

MODE button: Switches tuning to an FM station between automatic tuning and manual

tuning.

16.

MEMORY button: Used to register FM radio stations.

































30°

Approx.5 m

8

> Before Start >Part Names > Install > Initial Setup > Playback

Advanced Setup | Firmware Update | Others

E

N

Main Unit (Display)

1. Lights in the following conditions.

HDMI: HDMI signals are input and selected.

ARC: Audio signals from the ARC compatible TV are input and selected.

USB: When "USB" is selected with the input selector and the unit is connected by USB

and the USB device is selected. Flashes if the USB is not properly connected.

NET: When "NET" is selected with the input selector and the unit is connected to the

network. It will flash if the connection to the network is not correct.

DIGITAL: Digital signals are input and the digital input selector is selected.

2. Lights when operating the "NET" or "USB" input selector indicating remote controller

cursor operations are possible in screens showing list of tracks, for example.

3. Lights when headphones are connected.

4. Lights when operating the "NET" or "USB" input selector when tracks are played or

paused.

5. Lights according to the type of input digital audio signals and the listening mode.

6. Lights in the following conditions.

RDS: Receiving RDS broadcasting.

AUTO: When tuning mode is auto.

TUNED: Receiving FM radio.

FM STEREO: Receiving FM stereo.

SLEEP: Sleep timer has been set.

ASb: When Auto Standby function is enabled. (ÄP51)

7. Flashes when muting is on.

8. Displays various information of the input signals. Characters that cannot be displayed on

this unit are replaced with asterisks ( ＊ ).











 

> Before Start >Part Names > Install > Initial Setup > Playback

Advanced Setup | Firmware Update | Others

9

E

N

Sound Bar

1. Height left speaker

2. Height right speaker

3. Front left speaker

4. Center speaker

5. Front right speaker

6. Speaker jacks: Connect to the main unit using the included sound bar connection cable.

7. Holes for attaching to the wall: The sound bar can be attached to the wall by putting these

holes on wood screws, etc., that are fixed to the wall. The holes for attaching to the wall

are on the rear of the sound bar, in two places 580 mm apart.

0 The wood screws, etc., to fit the brackets to the wall are not included. Consult with a

professional to make sure you select the type, material, length, etc., that will provide

sufficient support. Add a reinforcing plate or anchor if reinforcement is necessary.

0 We accept no responsibility for damage or injury that arises due to incorrect fitting,

incomplete fitting, incorrect use, or acts of nature.







 

10 mm

5 mm





10

> Before Start >Part Names > Install > Initial Setup > Playback

Advanced Setup | Firmware Update | Others

E

N

Subwoofer

1. LINK LED: Lights when paired with the main unit.

2. LINK button: Used to pair the subwoofer and the main unit.

3. AC INLET: The supplied power cord is connected.

The wireless connection setting between the subwoofer and the main unit was completed at

the time of shipping. You need only connect the power cord to start using the unit.

0 If LINK LED is flashing and you do not hear sound from the subwoofer, go to

"Troubleshooting" and check "The subwoofer produces no sound" (ÄP57).







11

> Before Start > Part Names >Install > Initial Setup > Playback

Advanced Setup | Firmware Update | Others

E

N

Install

1. Connect the Speakers

a Non-skid pads

a

1

3

2

Setting up the sound bar

The sound bar outputs the audio for the front speakers and

center speaker from the front, and the audio for the height

speakers from the top. Set up in front of the TV so the logo

faces up.

Setting up the Subwoofer

Attach the included pads to the four corners of the bases of

the subwoofer. This makes the speakers less likely to slip,

improve the stability of the installation, and enables better

sound. The connection between the main unit and the

subwoofer is wireless. Put the subwoofer within 10 m of the

main unit. Also, place so there are no obstacles such as

walls between the main unit and the subwoofer.

The directionality of subwoofers, where hearing discerns the direction

of sound, is weak, so you will get the same effect from the subwoofer

wherever you decide to put it in the room.

12

> Before Start > Part Names >Install > Initial Setup > Playback

Advanced Setup | Firmware Update | Others

E

N

a Sound bar connection cable

a

1

2

a

Connecting the sound bar

Refer to the illustration to connect the sound bar. Match the

facing of the cable connector to the port, and make sure

that it is pushed in all the way.

13

> Before Start > Part Names >Install > Initial Setup > Playback

Advanced Setup | Firmware Update | Others

E

N

2. Connect the TV

a HDMI cable, b Digital optical cable

a

b

DIGITAL

OPTICAL OUT

1

To ARC TV

For a TV that supports the ARC (Audio Return Channel)

(ÄP63) feature, use an HDMI cable and connect according

to illustration "a". Choose an HDMI IN jack on the TV that

supports ARC when connecting.

To Non-ARC TV

For a TV that does not support the ARC (Audio Return

Channel) feature, connect both the HDMI cable in illustration

"a" and the digital optical cable in "b".

Setup

0 Settings are required to use the ARC function. Select

"Yes" in "4. Audio Return Channel" (ÄP18) in the Initial

Setup.

0 Please refer to the TV’s operation manual for directions on

connections and setup for the TV.

14

> Before Start > Part Names >Install > Initial Setup > Playback

Advanced Setup | Firmware Update | Others

E

N

3. Connect the HDMI AV Components

a HDMI cable

e.g. BD

a

HDMI OUT

1

BD/DVD

GAME

a

Cable/Satellite

set-top box

Streaming media

player

This is an example of connection with an AV component

that has an HDMI jack. With connection to an AV

component that conforms with the CEC (Consumer

Electronics Control) standard, you can use features such as

the HDMI CEC feature that links with the input selector, and

the HDMI Standby Through feature which allows you to

play video and audio from AV components on the TV even

when this unit is in standby mode. (ÄP63)

0 To play 4K or 1080p video, use the high speed HDMI

cable.

Setup

0 Settings are required to use the HDMI CEC and HDMI

Standby Through features. (ÄP47, 48) Make settings after

all connections are complete.

0 To enjoy digital surround sound including Dolby Digital,

audio output should be set to "Bitstream output" on the

connected Blu-ray Disc player or other device.

15

> Before Start > Part Names >Install > Initial Setup > Playback

Advanced Setup | Firmware Update | Others

E

N

4. Connect the Audio Components

a Analog audio cable

CD

a

Connecting a CD player

Use an analog audio cable to connect a CD player to the

AUDIO IN jack.

16

> Before Start > Part Names >Install > Initial Setup > Playback

Advanced Setup | Firmware Update | Others

E

N

5. Connect Other Cables

a FM indoor antenna, b Ethernet cable, c Power cord (Main unit), d Power cord (for subwoofer)

b

a

c

d

c

1 2

3 4

Antenna Hookup

Connect the supplied FM indoor antenna to the TUNER FM

75 terminal. Move the FM indoor antenna around while

playing the radio to find the position with the best reception.

Network Hookup

Connect this unit to the network using wired LAN or Wi-Fi

(wireless LAN). You can enjoy network features such as

internet radio by connecting the unit to the network. If you

connect by wired LAN, connect with an Ethernet cable to the

ETHERNET port as shown in the illustration. To connect by

Wi-Fi, then after selecting "Wireless" in "3. Network

Connection" (ÄP18) in Initial Setup, select the desired

setting method and follow the onscreen instructions to

configure the connection.

Power Cord Hookup

Connect the power cords of the main unit and subwoofer

after all other connections are completed.

17

> Before Start > Part Names > Install > Initial Setup >Playback

Advanced Setup | Firmware Update | Others

E

N

Initial Setup

Initial Setup with Auto Start-up Wizard

1

3 4

2

TV's remote controller

Initial Setup starts automatically

1. Switch the input on the TV to that assigned to the unit.

2. Put batteries into the remote controller of this unit.

3. Press Í on the remote controller. When power is turn on

for the first time, an Initial Setup screen is automatically

displayed on the TV to allow you to make settings

required for start up.

4. Follow the on-screen instructions to select the item with

the cursors of the remote controller and press ENTER to

confirm your selection.

0 To return to the previous screen, press .

To redo Initial Setup: If you terminate the procedure on the

way or want to change a setting made during Initial Setup,

press on the remote controller, select "6. Miscellaneous"

- "Initial Setup" in the Setup menu and press ENTER. To

select the language displayed again, change "OSD

Language". (ÄP41)

Exit

Initial Setup

Language Select

English

Deutsch

Français

Español

Italiano

Nederlands

Svenska

Русский язык

18

> Before Start > Part Names > Install > Initial Setup >Playback

Advanced Setup | Firmware Update | Others

E

N

1. AccuEQ Room Calibration

Place the supplied speaker setup microphone in the

listening position, measure the test tones emitted by the

speakers, then the unit automatically sets the optimum

volume level for each speaker and the distance from the

listening position. This also automatically adjusts the

equalizers for the speakers and enables correction of

distortion caused by the acoustic environment of the room.

0 Calibration takes between 3 to 12 minutes to be

completed. The speakers emit the test tone at high

volume during measurement, so be careful of your

surroundings. Keep the room as quiet as possible during

measurement.

1. Place the supplied speaker setup microphone in the

listening position, and connect to the SETUP MIC jack on

the main unit. A confirmation screen is displayed, so

follow the on screen instructions.

When putting the speaker setup microphone on a tripod,

refer to the illustration when putting it in place.

0 To cancel AccuEQ Room Calibration partway through,

disconnect the speaker setup microphone.

2. Test tones are emitted by the speakers, and firstly the

unit detects the speakers connected and the noise in the

environment.

3. After the results of the above measurements are

displayed, select "Next", press ENTER on the remote

controller, and the test tones are emitted again, and the

unit automatically makes settings such as the optimum

volume level and the distance from the listening position.

4. Disconnect the speaker setup microphone.You cannot

use any other menu options while it is connected.

2. Source Connection

Check that each input source is connected correctly. Follow

the guidance, select the input you want to confirm, start play

of the selected player, and confirm that the images appear

on the TV and that sound is played.

3. Network Connection

Set up Wi-Fi connection with an access point such as a

wireless LAN router. There are the following two methods of

connecting by Wi-Fi:

"Scan Networks": Search for an access point from this

unit. Find out the SSID of the access point beforehand.

"Use iOS Device (iOS7 or later)": Share the iOS device's

Wi-Fi settings with this unit.

If you select "Scan Networks", there are a further two

choices of connection method. Check the following.

0 "Enter Password": Enter the password (or key) of the

access point to connect.

0 "Push Button": If the access point has an automatic

connection button, you can connect without entering a

password.

0 If the SSID of the access point is not displayed, then in

the screen listing the SSIDs, select "Other..." with the X

button on the remote controller and press ENTER, then

follow the on-screen instructions.

Keyboard input: To switch between upper and lower case,

select "A/a" on the screen and press ENTER. To select

whether to mask the password with " " or display it in

plain text, press MEMORY on the remote controller.

Pressing CLEAR will delete all the input characters.

Privacy policy: A confirmation screen asking you to agree

to the privacy policy is displayed during network setting.

Select "Yes" and press ENTER to indicate agreement.

4. Audio Return Channel

If you have connected a TV that supports ARC, select

"Yes". This unit's ARC setting turns on and you can listen to

the TV's audio through this unit.

0 If you select "Yes", the HDMI CEC function is enabled

and power consumption increases during standby.

SETUP MIC

Wi-Fi Setup

Ðáóó÷ïòä

When finished, select the "OK" key.

A/aAll Erase

OKA/a

a b cdefghi jklm

nopqr s t uvwxy z

1 2 34567890- ^\

, . /;:@[]

Hide/Show

19

> Before Start > Part Names > Install > Initial Setup >Playback

Advanced Setup | Firmware Update | Others

E

N

Playback

AV Component Playback

Basic operations

Play an AV component or TV connected to this unit with an

HDMI cable or other cable.

1. Switch the input on the TV to that assigned to the unit.

2. Press the input selector (a) on the remote controller with

the same name as the jack to which you connected the

player to switch the input.

For example, press BD/DVD to play the player connected

to the BD/DVD jack. Press TV to listen the TV's sound.

0 Note that when the CEC link function works, the input

switches automatically when you have connected a

CEC compliant TV and player to this unit using HDMI

connection.

3. Start play on the player.

4. Use VOL+/– (b) to adjust the volume.

a

b

20

> Before Start > Part Names > Install > Initial Setup >Playback

Advanced Setup | Firmware Update | Others

E

N

Internet Radio

Basic operations

When this unit is connected to a network, you can listen to

TuneIn or other preregistered Internet radio services.

Depending on the internet radio service, the user may need

to register from their computer first.

1. Switch the input on the TV to that assigned to the unit.

2. Press NET on the remote controller.

3. Follow the on-screen instructions, using the cursors to

select radio stations and programs, then press ENTER

(a) to play. Play starts when 100% is displayed for

buffering.

0 To return to the previous screen, press (b).

0 If you cannot select a network service, it will become

selectable when the network function is started.

Regarding the TuneIn Radio

To display the TuneIn Radio menu during play, press

ENTER (a) on the remote controller.

Add to My Presets Registers radio stations being

broadcast and programs in "My Presets". Once registered,

"My Presets" is displayed in the level under TuneIn Radio.

To play, select the program you like from "My Presets".

Remove from My Presets Removes a radio station or

program from "My Presets" in TuneIn Radio.

1

a

b

Sidan laddas ...

ONKYO LS7200 - 3D SOUNDBAR SYSTEM Bruksanvisning

Denna manual är också lämplig för

ONKYO LS7200 - 3D SOUNDBAR SYSTEM Bruksanvisning

på andra språk

Relaterade papper

Andra dokument