Hilti TE 5-22 Användarmanual

TE 5-22

English 1

Dansk 14

Svenska 28

Norsk 41

Suomi 54

Eesti 67

Latviešu 81

Lietuvių 94

Türkçe 108

ﻋﺮﺑﻲ 122

日本語 137

한국어 150

繁體中文 163

中文 175

1

2

3

4

5

6

7

8

9

10

TE 5-22

en Originaloperatinginstructions....................................... 1

da Originalbrugsanvisning .......................................... 14

sv Originalbruksanvisning........................................... 28

no Originalbruksanvisning .......................................... 41

fi Alkuperäisetohjeet ............................................. 54

et Originaalkasutusjuhend .......................................... 67

lv Oriģinālālietošanasinstrukcija ..................................... 81

lt Originalinaudojimoinstrukcija...................................... 94

tr Orijinalkullanımkılavuzu ......................................... 108

ar ﺩﻟﻴﻞﺍﻻﺳﺘﻌﻤﺎﻝﺍﻷﺻﻠﻲ .......................................... 122

ja オリジナル取扱説明書 ............................................ 137

ko 오리지널사용설명서............................................. 150

zh 原始操作說明.................................................. 163

cn 原版操作说明.................................................. 175

*2351802* 2351802 English 1

Original operating instructions

1 Information about the operating instructions

1.1 About these operating instructions

• Read these operating instructions before the product is used or operated for the first time. This is a

prerequisite for safe, trouble-free handling and use of the product.

• Observe the safety instructions and warnings in these operating instructions and on the product.

• Always keep the operating instructions with the product and make sure that the product is accompanied

by these operating instructions only, when the product is given to other persons.

1.2 Explanation of symbols

1.2.1 Warnings

Warnings alert persons to hazards that occur when handling or using the product. The following signal words

are used:

DANGER

DANGER !

▶Draws attention to imminent danger that will lead to serious personal injury or fatality.

WARNING

WARNING !

▶Draws attention to a potential threat of danger that can lead to serious injury or fatality.

CAUTION

CAUTION !

▶Draws attention to a potentially dangerous situation that could lead to personal injury or damage to the

equipment or other property.

1.2.2 Symbols in the operating instructions

The following symbols are used in these operating instructions:

Comply with the operating instructions

Instructions for use and other useful information

Dealing with recyclable materials

Do not dispose of electric equipment and batteries as household waste

Hilti Liion battery

Hilti charger

1.2.3 Symbols in illustrations

The following symbols are used in illustrations:

These numbers refer to the illustrations at the beginning of these operating instructions.

The numbering reflects the sequence of operations shown in the illustrations and may deviate

from the steps described in the text.

Item reference numbers are used in the overview illustration and refer to the numbers used in

the key in the product overview section.

These characters are intended to specifically draw your attention to certain points when handling

the product.

2 English 2351802 *2351802*

1.3 Product-dependent symbols

1.3.1 Symbols on the product

The following symbols can be used on the product:

The product supports near-field communication (NFC) technology compatible with iOS and

Android platforms.

Hilti Li-ion battery type series used. Observe the information given in the section headed In-

tended use.

Never strike the battery with an object and never use the battery as a striking tool.

Do not drop the battery. Never use a battery that has suffered an impact or is damaged in any

other way.

Li-ion battery

Rated speed under no load

Direct current (DC)

Drilling without hammer action

Hammer drilling

Chisel position adjustment

Chiseling

Forward / reverse

If applied on the product, the product has been certified by this certification body for the US and

Canadian markets according to the applicable standards.

1.4 Product information

products are designed for professional users and only trained, authorized personnel are

permitted to operate, service and maintain the products. This personnel must be specifically informed about

the possible hazards. The product and its ancillary equipment can present hazards if used incorrectly by

untrained personnel or if used not in accordance with the intended use.

The type designation and serial number are printed on the rating plate.

▶Write down the serial number in the table below. You will be required to state the product details when

contacting Hilti Service or your local Hilti organization to inquire about the product.

Product information

Rotary hammer drill TE 5-22

Generation 01

Serial no.

1.5 Declaration of conformity

The manufacturer declares, on his sole responsibility, that the product described here complies with the

applicable legislation and standards. A copy of the declaration of conformity can be found at the end of this

documentation.

The technical documentation is filed here:

Hilti Entwicklungsgesellschaft mbH | Tool Certification | Hiltistrasse 6 | D-86916 Kaufering, Germany

2 Safety

2.1 General power tool safety warnings

WARNING Read all safety warnings, instructions, illustrations and specifications provided with this

power tool. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury.

*2351802* 2351802 English 3

Save all warnings and instructions for future reference.

The term "power tool" in the warnings refers to your mains-operated (corded) power tool or battery-operated

(cordless) power tool.

Work area safety

▶Keep work area clean and well lit. Cluttered or dark areas invite accidents.

▶Do not operate power tools in explosive atmospheres, such as in the presence of flammable

liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.

▶Keep children and bystanders away while operating a power tool. Distractions can cause you to lose

control.

Electrical safety

▶Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter

plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of

electric shock.

▶Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.

▶Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the

risk of electric shock.

▶Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep

cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the

risk of electric shock.

▶When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a

cord suitable for outdoor use reduces the risk of electric shock.

▶If operating a power tool in a damp location is unavoidable, use a residual current device (RCD)

protected supply. Use of an RCD reduces the risk of electric shock.

Personal safety

▶Stay alert, watch what you are doing and use common sense when operating a power tool. Do

not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A

moment of inattention while operating power tools may result in serious personal injury.

▶Use personal protective equipment. Always wear eye protection. Protective equipment such as a

dust mask, non-skid safety shoes, hard hat or hearing protection used for appropriate conditions will

reduce personal injuries.

▶Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power

source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on

the switch or energising power tools that have the switch on invites accidents.

▶Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left

attached to a rotating part of the power tool may result in personal injury.

▶Do not overreach. Keep proper footing and balance at all times. This enables better control of the

power tool in unexpected situations.

▶Dress properly. Do not wear loose clothing or jewellery. Keep your hair and clothing away from

moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.

▶If devices are provided for the connection of dust extraction and collection facilities, ensure these

are connected and properly used. Use of dust collection can reduce dust-related hazards.

▶Do not let familiarity gained from frequent use of tools allow you to become complacent and ignore

tool safety principles. A careless action can cause severe injury within a fraction of a second.

Power tool use and care

▶Do not force the power tool. Use the correct power tool for your application. The correct power tool

will do the job better and safer at the rate for which it was designed.

▶Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be

controlled with the switch is dangerous and must be repaired.

▶Disconnect the plug from the power source and/or remove the battery pack, if detachable, from

the power tool before making any adjustments, changing accessories, or storing power tools.

Such preventive safety measures reduce the risk of starting the power tool accidentally.

▶Store idle power tools out of the reach of children and do not allow persons unfamiliar with the

power tool or these instructions to operate the power tool. Power tools are dangerous in the hands

of untrained users.

▶Maintain power tools and accessories. Check for misalignment or binding of moving parts,

breakage of parts and any other condition that may affect the power tool’s operation. If damaged,

have the power tool repaired before use. Many accidents are caused by poorly maintained power

tools.

4 English 2351802 *2351802*

▶Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are

less likely to bind and are easier to control.

▶Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking

into account the working conditions and the work to be performed. Use of the power tool for

operations different from those intended could result in a hazardous situation.

▶Keep handles and grasping surfaces dry, clean and free from oil and grease. Slippery handles and

grasping surfaces do not allow for safe handling and control of the tool in unexpected situations.

Battery tool use and care

▶Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type

of battery pack may create a risk of fire when used with another battery pack.

▶Use power tools only with specifically designated battery packs. Use of any other battery packs may

create a risk of injury and fire.

▶When battery pack is not in use, keep it away from other metal objects, like paper clips, coins,

keys, nails, screws or other small metal objects, that can make a connection from one terminal to

another. Shorting the battery terminals together may cause burns or a fire.

▶Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact

accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid

ejected from the battery may cause irritation or burns.

▶Do not use a battery pack or tool that is damaged or modified. Damaged or modified batteries may

exhibit unpredictable behaviour resulting in fire, explosion or risk of injury.

▶Do not expose a battery pack or tool to fire or excessive temperature. Exposure to fire or temperature

above 130° C (265 °F) may cause explosion.

▶Follow all charging instructions and do not charge the battery pack or tool outside the temperature

range specified in the instructions. Charging improperly or at temperatures outside the specified range

may damage the battery and increase the risk of fire.

Service

▶Have your power tool serviced by a qualified repair person using only identical replacement parts.

This will ensure that the safety of the power tool is maintained.

▶Never service damaged battery packs. Service of battery packs should only be performed by the

manufacturer or authorized service providers.

2.2 Hammer safety warnings

Safety instructions for all operations

▶Wear ear protectors. Exposure to noise can cause hearing loss.

▶Use auxiliary handle(s), if supplied with the tool. Loss of control can cause personal injury.

▶Hold the power tool by insulated gripping surfaces, when performing an operation where the

cutting accessory may contact hidden wiring. Cutting accessory contacting a "live" wire may make

exposed metal parts of the power tool "live" and could give the operator an electric shock.

Safety instructions when using long drill bits with rotary hammers

▶Always start drilling at low speed and with the bit tip in contact with the workpiece. At higher

speeds, the bit is likely to bend if allowed to rotate freely without contacting the workpiece, resulting in

personal injury.

▶Apply pressure only in direct line with the bit and do not apply excessive pressure. Bits can bend

causing breakage or loss of control, resulting in personal injury.

2.3 Additional safety instructions

Personal safety

▶Use the product and accessories only when they are in perfect working order.

▶Never tamper with or modify the product or accessories in any way.

▶Wear eye protection, a hard hat and ear protection while the product is in use.

▶Dust produced by grinding, sanding, cutting and drilling can contain dangerous chemicals. Some

examples are: lead or lead-based paints; brick, concrete and other masonry products, natural stone

and other products containing silicates; certain types of wood, such as oak, beech and chemically

treated wood; asbestos or materials that contain asbestos. Determine the exposure of the operator and

bystanders by means of the hazard classification of the materials to be worked. Implement the necessary

measures to restrict exposure to a safe level, for example by the use of a dust collection system or by

the wearing of suitable respiratory protection. The general measures for reducing exposure include:

▶working in an area that is well ventilated,

*2351802* 2351802 English 5

▶avoidance of prolonged contact with dust,

▶directing dust away from the face and body,

▶wearing protective clothing and washing exposed areas of the skin with water and soap.

▶Do not look directly into the light source (LEDs) incorporated in the power tool and do not direct the light

at other persons’ faces.

▶Always hold the product with both hands on the grips provided. Keep the grips dry, clean and free from

oil and grease.

▶Take frequent breaks and do physical exercises to improve the blood circulation in your fingers. High

vibration during long periods of work can lead to disorders of the blood vessels and nervous system in

the fingers, hands and wrists.

▶Do not touch rotating parts. Switch the product on only after it is in position at the workpiece. Touching

rotating parts, especially rotating accessory tools, can result in injury.

▶Activate the switch-on interlock (forward/reverse switch in the middle position) for storing or transporting

the product.

▶The product is not intended for use by debilitated persons who have received no special training. Keep

the product out of reach of children.

▶If the work involves breaking right through, take the appropriate safety measures on the opposite side.

Parts breaking away could fall out and / or fall down and injure other persons.

▶Before beginning work, check the working area for concealed electric cables or gas and water pipes.

External metal parts of the product could give you an electric shock or cause an explosion if you

accidentally damage an electric cable or a gas or water pipe.

▶In accordance with the applications for which it is designed, the product produces a high torque. Always

use the side handle and hold the product with both hands. The user must be prepared for sudden

sticking and stalling of the accessory tool.

▶Secure the workpiece. Use clamps or a vice to secure the workpiece. The workpiece is thus held more

securely than by hand and in addition, both hands remain free to operate the product.

▶Wear protective gloves. The product can get hot during operation. There is a risk of injury (cutting or

burning) if the accessory tool is touched while changing it.

▶Keep the air vents clear at all times. Risk of burn injuries due to blocked air vents!

▶Working on the material may cause it to splinter. Wear eye protection, protective gloves and, if you are

not using a dust removal system, wear light respiratory protection. Flying fragments present a risk of

injury to the eyes and body.

▶Risk of injury by falling tools and/or accessories. Before starting work, check that installed accessories

are secure.

▶Do not attach a belt hook to this product.

2.4 Careful handling and use of batteries

▶Comply with the following safety instructions for the safe handling and use of Li-ion batteries.

Failure to comply can lead to skin irritation, severe corrosive injury, chemical burns, fire and/or explosion.

▶Use only batteries that are in perfect working order.

▶Treat batteries with care in order to avoid damage and prevent leakage of fluids that are extremely

harmful to health!

▶Do not under any circumstances modify or tamper with batteries!

▶Do not disassemble, crush or incinerate batteries and do not subject them to temperatures over 80 °C

(176 °F).

▶Never use or charge a battery that has suffered an impact or been damaged in any other way. Check

your batteries regularly for signs of damage.

▶Never use recycled or repaired batteries.

▶Never use the battery or a battery-operated power tool as a striking tool.

▶Never expose batteries to the direct rays of the sun, elevated temperature, sparking, or open flame. This

can lead to explosions.

▶Do not touch the battery poles with your fingers, tools, jewelry, or other electrically conductive objects.

This can damage the battery and also cause material damage and personal injury.

▶Keep batteries away from rain, moisture and liquids. Penetrating moisture can cause short circuits,

electric shock, burns, fire and explosions.

▶Use only chargers and power tools approved for the specific battery type. Read and follow the relevant

operating instructions.

▶Do not use or store the battery in explosive environments.

6 English 2351802 *2351802*

▶If the battery is too hot to touch, it may be defective. Put the battery in a place where it is clearly visible

and where there is no risk of fire, at an adequate distance from flammable materials. Allow the battery to

cool down. If it is still too hot to touch after an hour, the battery is faulty. Consult Hilti Service or read the

document entitled "Instructions on safety and use for Hilti Li-ion batteries".

Observe the special guidelines applicable to the transport, storage and use of lithium-ion batteries.

Read the instructions on safety and use of Hilti Li-ion batteries that you can access by scanning

the QR code at the end of these operating instructions.

3 Description

3.1 Product overview 1

@Dust cap

;Locking sleeve

=Clamping band

%Connection for dust collection module (DCD)

&Mount for depth gauge

(Depth gauge

)Function selector switch

+Forward/reverse switch

§Control switch

/Electrical interface

Dust removal module (TE DRS-5)

:Work-area light

∙Battery release button

$Battery status indicator

£Battery

|Auxiliary handle

¡Release button, auxiliary handle

QLocking pin, dust removal module (TE DRS-

5)

WSealing lip

ETool holder (SDS)

3.2 Intended use

The product described is a cordless rotary hammer drill. It is designed for drilling in steel, wood and masonry,

for hammer-action drilling in concrete and masonry, and for driving and removing screws. The product can

also be used for light chiseling work on masonry and for surface finishing on concrete.

• For this product, use only Hilti lithiumion batteries of the B 22 series. For this product, Hilti recommends

the use of the batteries stated in the table at the end of these operating instructions.

• For these batteries, use only Hilti chargers of the type series listed at the end of these operating

instructions.

3.3 Items supplied

Rotary hammer drill, operating instructions

Other system products approved for use with this product can be found at your local Hilti Store or at:

www.hilti.group

3.4 Status indicators of the Liion battery

Hilti Nuron Li-ion batteries can indicate state of charge, fault messages and the battery's state of health.

*2351802* 2351802 English 7

3.4.1 Indicators for state of charge and fault messages

WARNING

Risk of injury by a falling battery!

▶If the release button is pressed with a battery inserted in the product, subsequently check that the battery

is correctly re-engaged and secure.

Short-press the release button of the battery to get whichever of the following status indications is applicable

at the time.

State of charge and, if applicable, faults are indicated constantly as long as the connected product is

switched on.

Status Meaning

Four (4) LEDs show constantly green State of charge: 100 % to 71 %

Three (3) LEDs show constantly green State of charge: 70 % to 51 %

Two (2) LEDs show constantly green State of charge: 50 % to 26 %

One (1) LED shows constantly green State of charge: 25 % to 10 %

One (1) LED slow-flashes green State of charge: < 10 %

One (1) LED quick-flashes green The Li-ion battery is completely discharged.

Recharge the battery.

If the LED again starts quick-flashing after the bat-

tery has been charged, consult Hilti Service.

One (1) LED quick-flashes yellow The Li-ion battery or the product in which it is in-

serted is overloaded, too hot or too cold, or experi-

encing some other fault.

Bring the product and the battery to the recom-

mended working temperature and do not overload

the product when it is in use.

If the message persists, consult Hilti Service.

One (1) LED shows yellow The Li-ion battery and the product in which it is

inserted are not compatible. Consult Hilti Service.

One (1) LED quick-flashes red The Li-ion battery is locked and cannot be used.

Consult Hilti Service.

3.4.2 Indicators showing the battery's state of health

To check the battery's state of health, press the release button and hold it down for longer than three

seconds. The system does not detect a potential malfunction of the battery due to misuse, for example

battery dropped or pierced, external heat damage, etc.

Status Meaning

All LEDs show in sequence, followed by one (1)

LED showing constantly green. The battery can remain in use.

All LEDs show in sequence, followed by one (1)

LED quick-flashing yellow. The check to ascertain the battery's state of health

did not complete. Repeat the procedure, or consult

Hilti Service.

All LEDs show in sequence, followed by one (1)

LED showing constantly red. If a connected product can still be used, the re-

maining battery capacity is below 50 %.

If a connected product can no longer be used, the

battery has reached the end of its useful life and

has to be replaced. Consult Hilti Service.

4 Technical data

Weight in accordance with EPTA Procedure 01, without battery 2.7 kg

Single impact energy in accordance with EPTA procedure 05 2.5 J

Drilling diameter range in concrete/masonry (hammer drilling) 4 mm … 28 mm

8 English 2351802 *2351802*

Storage temperature −20 ℃ … 70 ℃

Ambient temperature for operation −17 ℃ … 60 ℃

4.1 Battery

Battery operating voltage 21.6 V

Weight, battery See the end of these operating

instructions

Ambient temperature for operation −17 ℃ … 60 ℃

Storage temperature −20 ℃ … 40 ℃

Battery charging starting temperature −10 ℃ … 45 ℃

4.2 Noise information and vibration values in accordance with EN 62841

The sound pressure and vibration values given in these instructions were measured in accordance with a

standardized test and can be used to compare one power tool with another. They can also be used for a

preliminary assessment of exposure.

The data given represent the main applications of the power tool. However, if the power tool is used for

different applications, with different accessory tools, or is poorly maintained, the data can vary. This can

significantly increase exposure over the total working period.

An accurate estimation of exposure should also take into account the times when the tool is switched off, or

when it is running but not actually being used for a job. This can significantly reduce exposure over the total

working period.

Identify additional safety measures to protect the operator from the effects of noise and/or vibration, for

example: maintaining the power tool and accessory tools, keeping the hands warm, organization of work

patterns.

Noise emission values

TE 5-22 TE 522 + TE DRS-

5 (01)

Emission sound pressure level (LpA)95 dB(A) 95 dB(A)

Uncertainty for the sound pressure level (KpA)3 dB(A) 3 dB(A)

Sound power level (LWA)106 dB(A) 106 dB(A)

Uncertainty for the sound power level (KWA)3 dB(A) 3 dB(A)

Total vibration

TE 5-22 TE 522 + TE DRS-

5 (01)

Hammer drilling in concrete (ah,HD) B 2285 14.2 m/s² 15.1 m/s²

B 22170 13 m/s² 14.8 m/s²

Chiseling B 2285 10.3 m/s² 10.9 m/s²

B 22170 9.9 m/s² 10.5 m/s²

Uncertainty (K) 1.5 m/s² 1.5 m/s²

5 Preparations at the workplace

WARNING

Risk of injury by inadvertent starting!

▶Before inserting the battery, make sure that the product is switched off.

▶Remove the battery before making any adjustments to the power tool or before changing accessories.

Observe the safety instructions and warnings in this documentation and on the product.

5.1 Charging the battery

1. Before charging the battery, read the operating instructions for the charger.

2. Make sure that the contacts on the battery and the contacts on the charger are clean and dry.

*2351802* 2351802 English 9

3. Use an approved charger to charge the battery. → page 6

5.2 Inserting the battery

WARNING

Risk of injury by short circuit or falling battery!

▶Before inserting the battery, make sure that the contacts on the battery and the contacts on the product

are free of foreign matter.

▶Make sure that the battery always engages correctly.

1. Charge the battery fully before using it for the first time.

2. Push the battery into the product until it engages with an audible click.

3. Check that the battery is seated securely.

5.3 Removing the battery

1. Press the battery release button.

2. Remove the battery from the product.

5.4 Installing auxiliary handle 2

1. Turn the auxiliary handle counter-clockwise.

▶The clamping band gets longer.

2. Slip the clamping band over the tool holder.

3. Position the auxiliary handle.

4. Turn the auxiliary handle clockwise.

▶The clamping band pulls tight round the tool holder.

5.5 Fitting the depth gauge 3

1. Press and hold down the release button on the auxiliary handle.

2. Insert the depth gauge into the mount for depth gauge on the auxiliary handle.

3. Let go of the release button on the auxiliary handle.

▶The depth gauge is locked.

5.6 Removing the depth gauge

1. Press and hold down the release button on the auxiliary handle.

2. Pull the depth gauge out of the mount for depth gauge on the auxiliary handle.

3. Let go of the release button on the auxiliary handle.

5.7 Changing the accessory tool 4

CAUTION

Risk of injury by the accessory tool! The accessory tool might be hot or have sharp edges.

▶Wear protective gloves when changing the accessory tool.

Lightly grease the connection end of the accessory tool before inserting it.

Use only genuine Hilti grease, to prevent damage to the product.

1. Pull the locking sleeve back and remove the accessory tool.

2. Insert the accessory tool into the tool holder (SDS).

3. Turn the accessory tool and push it into the tool holder (SDS) until it engages with an audible click.

▶The accessory tool is locked.

4. Check that the accessory tool is securely locked.

5.8 Installing dust collection module for overhead work (accessory) 5

1. Insert the retaining lugs of the dust collection module into the connections for the dust collection module.

10 English 2351802 *2351802*

2. Turn the dust collection module counter-clockwise.

▶The dust collection module is locked.

5.9 Fitting the dust removal module (accessory) 6

1. Move the forward/reverse switch on the rotary hammer drill to the middle position.

2. Remove the depth gauge. → page 9

3. Turn the auxiliary handle to a position where it is not in the way.

4. Hook the dust removal module into the locking pins on the rotary hammer drill.

When hooking the module into position, be sure to pass the accessory tool of the rotary hammer

drill through the extraction head of the dust removal module.

5. Press the electrical interface into the rotary hammer drill until the dust removal module engages with an

audible click.

6. Check that the dust removal module is correctly engaged.

5.10 Removing dust removal module (accessory) 7

1. Move the forward/reverse switch on the rotary hammer drill to the middle position.

2. Press and hold down the catch on the dust removal module.

3. Pull the electrical interface out of the rotary hammer drill.

4. Unhook the dust removal module from the locking pins on the rotary hammer drill.

5.11 Fall arrest

WARNING

Risk of injury by falling tool and/or accessory!

▶Use only the Hilti tool tether recommended for your product.

▶Prior to each use, always check the attachment point of the tool tether for possible damage.

Comply with the national regulations for working at heights.

As drop arrester for this product, use only a combination of the Hilti retaining strap and the Hilti tool tether

#2261970.

▶Secure the retaining strap to the installation openings for accessories. Check that it holds securely.

▶Secure one carabiner of the tool tether to the retaining strap and secure the second carabiner to a

load-bearing structure. Check that both carabiners hold securely.

Comply with the operating instructions of the Hilti retaining strap and those of the Hilti tool tether.

6 Operation

Observe the safety instructions and warnings in this documentation and on the product.

6.1 Operation 8

1. Install the auxiliary handle. → page 9

2. Fit the depth gauge. → page 9

3. Fit the dust removal module. → page 10

Install the dust collection module only for overhead work.

4. Install the dust collection module for overhead work. → page 9

5. Adjust the depth gauge.

*2351802* 2351802 English 11

6. Set the function selector switch to the desired function.

Options

Drilling

Hammer drilling

Chisel positioning

Chiseling

7. Change the accessory tool. → page 9

8. Hold the rotary hammer drill in position.

9. Press the control switch.

Speed of rotation can be regulated steplessly by means of the control switch.

10. Release the control switch to cease operation.

6.2 Setting direction of rotation 9

1. Operate the forward/reverse switch.

2. Select the desired position.

Options

Forward rotation Rotary hammer drill rotates clockwise.

Lock Rotary hammer drill is locked.

Reverse rotation Rotary hammer drill rotates counter-clockwise.

▶The switch engages in the desired position.

7 Care and maintenance

WARNING

Risk of injury with battery inserted !

▶Always remove the battery before carrying out care and maintenance tasks!

Care of the product

• Carefully remove stubborn dirt.

• Carefully clean the air vents, if present, with a dry, soft brush.

• Use only a slightly damp cloth to clean the housing. Do not use cleaning agents containing silicone as

these can attack the plastic parts.

• Use a dry, clean cloth to clean the contacts of the product.

Care of the Liion batteries

• Never use a battery with clogged air vents. Clean the air vents carefully using a dry, soft brush.

• Avoid unnecessary exposure of the battery to dust and dirt. Never expose the battery to high levels of

moisture (e.g. by being dipped in water or left in the rain).

If a battery has been soaked by moisture, treat it as a damaged battery. Isolate it in a non-flammable

container and consult Hilti Service.

• Keep the battery free of extraneous oil and grease. Do not permit dust or dirt to accumulate unnecessarily

on the battery. Clean the battery with a dry, soft brush or a clean, dry cloth. Do not use cleaning agents

containing silicone as these can attack the plastic parts.

Do not touch the contacts of the battery and do not remove the factory-applied grease from the contacts.

• Use only a slightly damp cloth to clean the housing. Do not use cleaning agents containing silicone as

these can attack the plastic parts.

Maintenance

WARNING

Danger of electric shock! Improper repairs to electrical components may lead to serious injuries including

burns.

▶Repairs to the electrical section of the tool or appliance may be carried out only by trained electrical

specialists.

12 English 2351802 *2351802*

• Check all visible parts and controls for signs of damage at regular intervals and make sure that they all

function correctly.

• Do not use the product if signs of damage are found or if parts malfunction. Immediately have the product

repaired by Hilti Service.

• After cleaning and maintenance, install all guards and protective devices and check that they are in full

working order.

To help ensure safe and reliable operation, use only genuine Hilti spare parts, consumables and

accessories. Spare parts, consumables and accessories approved by Hilti for use with your product

can be found at your Hilti Store or online at: www.hilti.group

7.1 Cleaning dust cap

1. Wipe the dust cap down with a clean, dry cloth.

2. Wipe the sealing lip down with a clean, dry cloth.

Replace the dust cap if the sealing lip is damaged.

3. Lightly grease the sealing lip.

Use only genuine Hilti grease, to prevent damage to the product.

7.2 Replacing the dust shield 10

1. Pull the locking sleeve back and remove the dust cap.

2. Clean the mount for the dust cap.

3. Press the dust cap into the mount until the dust cap engages with an audible click.

8 Transport and storage

Transport of cordless power tools and batteries

CAUTION

Accidental starting during transport !

▶Always transport your products with the batteries removed!

▶Remove the battery/batteries.

▶Never transport batteries loose and unprotected. During transport, batteries should be protected from

excessive shock and vibration and isolated from any conductive materials or other batteries that may

come in contact with the terminals and cause a short circuit. Comply with the locally applicable

regulations for transporting batteries.

▶Do not send batteries through the mail. Consult your shipper for instructions on how to ship undamaged

batteries.

▶Prior to each use and before and after prolonged transport, check the product and the batteries for

damage.

Storage of cordless power tools and batteries

WARNING

Accidental damage caused by defective or leaking batteries !

▶Always store your products with the batteries removed!

▶Store the product and the batteries in a cool and dry place. Comply with the temperature limits stated in

the technical data.

▶Do not store batteries on the charger. Always remove the battery from the charger when the charging

operation has completed.

▶Never leave batteries in direct sunlight, on sources of heat, or behind glass.

▶Store the product and batteries where they cannot be accessed by children or unauthorized persons.

▶Prior to each use and before and after prolonged storage, check the product and the batteries for

damage.

*2351802* 2351802 English 13

9 Troubleshooting

If a problem occurs, always observe the charge-status and fault indicator of the battery. See the section

headed Status indicators of the Liion battery.

If the trouble you are experiencing is not listed in this table or you are unable to remedy the problem by

yourself, please contact Hilti Service.

Trouble or fault Possible cause Action to be taken

The control switch can’t be

pressed, i.e. the switch is

locked.

Forward/reverse switch centered. ▶Push the forward/reverse switch

to the right or left.

The drive spindle does not

rotate. The battery is not fully inserted. ▶Push the battery in until it

engages with an audible click.

Forward/reverse switch centered. ▶Push the forward/reverse switch

to the right or left.

The function selector switch is not

engaged or is in the "Chiseling"

position or the "Chisel position-

ing" position .

▶With the motor of the power

tool at a complete stop, set

the function selector switch to

“Drilling without hammering”

or "Hammer drilling" .

No hammering action. The function switch is set to

“Drilling without hammering” .

▶Set the function switch to

“Hammer drilling” .

The rotary hammer drill is too cold. ▶Bring the tip of the drill bit

into contact with the working

surface, switch the rotary

hammer drill on and allow it to

run. If necessary, repeat the

procedure until the hammering

mechanism begins to operate.

The battery runs down more

quickly than usual. Battery condition is not optimal. ▶Call up the condition of the

battery. → page 6

The battery doesn’t engage

with an audible click. Retaining lug on the battery dirty. ▶Clean the retaining lug and refit

the battery.

LEDs of the battery show

nothing Battery defective ▶Contact Hilti Service.

The rotary hammer drill or the

battery gets very hot. Electrical fault ▶Switch off the rotary hammer

drill immediately. Remove

the battery and keep it under

observation. Allow it to cool

down. Contact Hilti service.

Accessory tool cannot be

released from the chuck. Locking sleeve not pulled back

fully.

▶Pull the locking sleeve back as

far as it will go and remove the

accessory tool.

Accessory tool makes no

progress. The rotary hammer drill has been

set to reverse rotation.

▶Switch the forward/reverse

switch to the "Forward" posi-

tion.

The function switch is set to

“Drilling without hammering” .

▶Set the function switch to

“Hammer drilling” .

10 Disposal

WARNING

Risk of injury due to incorrect disposal! Health hazards due to escaping gases or liquids.

▶DO NOT send batteries through the mail!

▶Cover the terminals with a non-conductive material (such as electrical tape) to prevent short circuiting.

▶Dispose of your battery out of the reach of children.

▶Dispose of the battery at your Hilti Store, or consult your local governmental garbage disposal or public

health and safety resources for disposal instructions.

14 Dansk 2351802 *2351802*

Most of the materials from which Hilti products are manufactured can be recycled. The materials must be

correctly separated before they can be recycled. In many countries, your old tools, machines or appliances

can be returned to Hilti for recycling. Ask Hilti Service or your Hilti sales representative for further information.

▶Do not dispose of power tools, electronic equipment or batteries as household waste!

11 Manufacturer’s warranty

▶Please contact your local Hilti representative if you have questions about the warranty conditions.

12 Further information

For more information on operation, technology, environment and recycling, follow this link:

qr.hilti.com/manual/?id=0000000&id=0000000

This link is also to be found at the end of the documentation, in the form of a QR code.

Original brugsanvisning

1 Om brugsanvisningen

1.1 Om denne brugsanvisning

• Læs brugsanvisningen grundigt igennem inden ibrugtagning. Det er en forudsætning for sikkert arbejde

og korrekt håndtering.

• Følg sikkerhedsanvisningerne og advarslerne i denne brugsanvisning og på produktet.

• Opbevar altid brugsanvisningen sammen med produktet, og overdrag kun produktet til andre personer

sammen med denne brugsanvisning.

1.2 Tegnforklaring

1.2.1 Advarsler

Advarsler advarer mod farer ved håndtering af produktet. Følgende signalord anvendes:

FARE

FARE !

▶Betegner en umiddelbart truende fare, der kan medføre alvorlige kvæstelser eller døden.

ADVARSEL

ADVARSEL !

▶Står ved en potentielt truende fare, der kan medføre alvorlige kvæstelser eller døden.

FORSIGTIG

FORSIGTIG !

▶Advarer om en potentielt farlig situation, der kan forårsage personskader eller materielle skader.

1.2.2 Symboler i brugsanvisningen

Der benyttes følgende symboler i denne brugsanvisning:

Se brugsanvisningen

Anvisninger for anvendelse og andre nyttige oplysninger

Håndtering af genvindbare materialer

Elektriske maskiner og batterier må ikke bortskaffes som almindeligt husholdningsaffald

Sidan laddas ...

Hilti TE 5-22 Användarmanual

Hilti TE 5-22 Användarmanual

på andra språk

Relaterade papper