Andersson WSR 2.0 Användarmanual

WSR 2.0 | Wireless router

User manual

English | Svenska | Norsk

Copyright

This manual is the copyright of CI no 556520-4137. No part of this manual may

be revised, copied or transmitted in any way without written permission from CI

no 556520-4137.

Statement

This manual does not provide any warranty or related declarations. All information

in this manual including the product speciﬁcation, pictures and literatures is just

for reference, CI no 556520-4137 reserves the rights to update contents of this

manual without further notice.

Copyright

Org.nr 556520-4137 äger upphovsrätten till den här handboken. Inga delar av

handboken får ändras, kopieras eller överföras utan skriftligt tillstånd från org.

nr 556520-4137.

Meddelande

Den här handboken innehåller inga garantier eller andra typer av utfästelser. All

information i handboken, inklusive tekniska data, bilder och texter, är endast ex-

empel och används i referenssyfte. Org.nr 556520-4137 förbehåller sig rätten att

upp-datera innehållet i handboken utan föregående meddelande.

Opphavsrett

Org.nr 556520-4137 har opphavsretten til denne håndboken. Ingen deler av denne

håndboken skal revideres, kopieres eller overføres på noen måte uten skriftlig sam-

tykke fra org.nr 556520-4137.

Erklæring

Denne håndboken gir ingen garanti eller tilhørende forsikringer. All informasjon

i denne håndboken, inklusiv produktspesiﬁkasjon, bilder og tekst, er bare ment

som referanse. Org.nr 556520-4137 forbeholder seg retten til å oppdatere innhol-

det i denne håndboken uten forvarsel.

English

Introduction 4

Getting Started 5

Adding Computers to the Wireless Router 6

Conﬁguring via Web Browser 7

Setup Wizard 8-9

Setup the Router mode 10

LAN Settings 11

Wireless Base Conﬁguration 12

Wireless Security Conﬁguration 13-14

Router Administrator Setup 15-17

Svenska

Inledning 18

Kom igång 19

Lägg till datorer till routern 20

Konﬁgurera via webbläsare 21

Installationsguiden 22-23

Ställ in Router-läge 24

LAN-inställningar 25

Grundinställningar för trådlöst 26

Konﬁguration av Trådlös säkerhet 27-28

Administrationsinställningar 29-31

Norsk

Innledning 32

Komme i gang 33

Koble en datamaskin til ruteren 34

Konﬁgurasjon via webleser 35

Konﬁgurasjonsveiviser 36-37

Konﬁgurere rutermodusen 38

LAN-innstillinger 39

Grundinställningar för trådlöst 40

Sikkerhetskonﬁgurasjon for trådløs 41-42

Administratorkonﬁgurasjon for ruter 43-45

Content / Innehållsförteckning / Register

English

4

Introduction

The WSR 2.0 Wireless Router is a combined wired/wireless network

connection device designed speciﬁcally for small business, ofﬁce,

and home ofﬁce networking requirements. It complies with the

IEEE 802.11n (Draft 2.0) standard. It adopts MIMO as well as SST

technologies. It also works well with other 11b/g and 11n protocol

wireless products. Create instant WiFi hotspots at any location where

you have Internet connection.

Package Contents

1 x Wireless Router

1 x Quick installation Guide

1 x Power adapter

1 x RJ-45 Networking Cable

English

5

Getting Started

Setting up a Wireless Infrastructure Network

Cable / DSL Modem

Wireless Router

Desktop PC or Laptop

(Wireless Adapter Required)

For a typical wireless setup at home (as shown above),

Please do the following:

1. You will need broadband Internet access (a ADSL, Cable

Modem line into your home or ofﬁce).

2. Consult with your ADSL or Cable Modem provider for proper

installation of the modem.

3. Connect the ADSL or Cable modem to the Wireless Router.

Plug in the Power Adapter to the Wireless Router.

4. Adding computers to the Wireless Router.

IMPORTANT NOTE

You can reset your Wireless Router to default setting by press the

‘RESET’ button on the back side of the Router.

You can use this solution if you forget your password.

English

6

Adding Computers to the Wireless Router

1. Log on to the computer.

2. Open Connect to a Network by right-clicking the network icon

( or ) in the notiﬁcation area.

3. Choose the wireless network from the list that appears, and

then click Connect.

4. Type the network security key or passphrase if you are asked to

do so, and then click OK.

You’ll see a conﬁrmation message when you are connected to

the network.

5. To conﬁrm that you added the computer, do the following:

Open Network by clicking the Start button , and then clicking

Control Panel. In the search box, type network, and then, under

Network and Sharing Center, click View network computers and

devices.

You should see icons for the computer you added and for the other

computers and devices that are part of the network.

Note : If you don’t see icons in the Network folder, then network

discovery and ﬁle sharing might be turned off.

For more information:

http://windows.microsoft.com/en-US/windows7/Add-a-device-or-computer-

to-a-network

http://windows.microsoft.com/en-US/windows7/Setting-up-a-Wirelessetwork

http://windows.microsoft.com/en-US/windows-vista/Setting-up-a-

Wirelessetwork

English

7

Conﬁguring via Web Browser

Open web browser and type http://192.168.0.1 in the browser’s

address box. This number is the default IP address for this device.

The login screen below will appear. Enter the “User Name” and

“Password” and click “OK” to login.

The default User name is “admin” and the Password is “admin”,

English

8

Setup Wizard

After successfully login, the following Router Summary will be

displayed on your web browser:

The setup wizard will guide you to conﬁgure access point for ﬁrst time.

English

9

1. WAN Connect Setting

If your ISP provides the DHCP service, please choose ‘dynamic

IP’, and the Router will automatically get IP parameters from

your ISP.

If your ISP provides a static or ﬁxed IP Address, Subnet

Mask, Gateway and DNS setting, select ‘static IP’. Enter

the IP address / Subnet Mask / Default Gateway / Primary /

Secondary DNS in dotted-decimalnotation provided by your

ISP.

If your ISP provides a username and a password for Dial-up.

Please choose “PPPoE”, Enter the Username and Password.

2. Wireless SSID Setting

3. Wireless Security Setting

English

10

Setup the Router mode

To Setup the router mode, please follow the following instructions:

Please click “Mode” located at the web management interface, the

following message will be displayed on your web browser:

Gateway

In this mode, the device is supposed to connect to internet via ADSL/

Cable Modem. The NAT is enabled and PCs in LAN ports share the

same IP to ISP through WAN port.

Bridge

In this mode, all ethernet ports and wireless interface are bridged

together and NAT function is disabled. All the WAN related function and

ﬁrewall are not supported.

Wireless ISP

In this mode, all ethernet ports are bridged together and the wireless

client will connect to ISP access point. The NAT is enabled and PCs in

ethernet ports share the same IP to ISP through wireless LAN. You can

connect to the ISP AP in Site-Survey page.

Click the Apply button to Change your Router Mode.

English

11

LAN Settings

Please click “Network -> Lan Setting” located at the web

management interface, the following message will be displayed on

your web browser:

IP Address: Enter the IP address of your Router or reset it in dotted-

decimal notation Wireless Router (factory default: 192.168.0.1).

Subnet Mask: An address code that determines the size of the

network. Normally use 255.255.255.0 as the subnet mask.

DHCP Type: Server, Client or Disable

Note:

´ If you change the IP Address of LAN, you must use the new IP

Address to login the Router.

´ If the new LAN IP Address you set is not in the same subnet, the

IP Address pool of the DHCP server will change accordingly at

the same time, while the Virtual Server and DMZ Host will not

take effect until they are re-conﬁgured.

English

12

Wireless Base Conﬁguration

Please click “Wireless -> Basic Setttings” located at the web

management interface, the following message will be displayed on

your web browser:

You could conﬁgure the minimum number of Wireless settings for

communication, such as Network Name (SSID) and Channel. The

Access Point can be set simply with only the minimum setting items.

Disable Wireless: Wireless On/Off.

Band: Supports 11G/11G/11N mixed modes.

SSID: Main Service Set Identiﬁer. It’s the “name” of

your wireless network.

Broadcast SSID: Select “enable” to enable the device’s SSID to

be visible by wireless clients

Channel Number: This ﬁeld determines which operating

frequency will be used. The default channel

is set to Auto, so the AP will choose the best

channel automatically. It is not necessary to

change the wireless channel unless you notice

interference problems with another nearby

access point.

English

13

Wireless Security Conﬁguration

Please click “Wireless-> Security” located at the web management

interface, the following message will be displayed on your web

browser:

Setup the wireless security and encryption to prevent from

unauthorized access and monitoring. Supports 64/128-bit WEP,

WPA, WPA2 encryption methods.

When you are ﬁnished, click ‘Apply’.

English

14

Please click “Wireless-> WPS” located at the web management

interface, the following message will be displayed on your web

browser:

You can establish a wireless connection between wireless adapter

and Router using either Push Button Conﬁguration (PBC) method or

PIN method.

Disable WPS: Enable / Disable

PIN method: If the new device supports Wi-Fi Protected Setup and

the PIN method, you can add it to the network by PIN.

PBC method: If the wireless adapter supports Wi-Fi Protected Setup

and the Push Button Conﬁguration (PBC)

Step 1: Press the WPS button of the Router directly for 2 - 3seconds

or Click web management interface ‘Start PBC’.

Step 2: Press the WPS button of the Adapter directly for 3 seconds.

Step 3: Wait for a while until the next screen appears.

Click Finish to complete the WPS conﬁguration.

English

15

Router Administrator Setup

Factory Default and Settings Backup , Restore

You can backup all Setting of this router to a ﬁle, so you can make

several copied of router conﬁguration for security reason.

To backup or restore router setting, please follow the following

instructions: Please click click ‘Management-> Backup&Reset’

located at the web management interface, then the following

message will be displayed on your web browser:

Save Settings Press ‘Save…’ button, and you’ll be prompted to

download the conﬁguration as a ﬁle, you can please

save it as another ﬁlename for different versions, and

keep it in a safe place.

Load Settings Press ‘Browse…’ to pick a previously-saved

conﬁguration ﬁle from your computer, and then click

‘Upload…’ to transfer the conﬁguration ﬁle to router.

After the conﬁguration is uploaded, the router’s

conﬁguration will be replaced by the ﬁle you just

uploaded.

Reset Settings Click this ‘Reset‘ button to remove all settings you

made, and restore the conﬁguration of this router back

to factory default settings

English

16

Firmware Upgrade

The system software used by this router is called as ‘ﬁrmware’, just

like any applications on your computer, when you replace the old

application with a new one, your computer will be equipped with new

function. You can also use this ﬁrmware upgrade function to add new

functions to your router, even ﬁx the bugs of this router.

Please click ‘Management-> Firmware Upgrade’ located at the

web management interface, then the following message will be

displayed on your web browser:

Click ‘Browse…’ button ﬁrst, you’ll be prompted to provide the

ﬁlename of ﬁrmware upgrade ﬁle. You may ask the retailer for

information regarding ﬁrmware, and use it to upgrade your router.

After a ﬁrmware upgrade ﬁle is selected, click ‘Upgrade‘ button, and

the router will start ﬁrmware upgrade procedure automatically. The

procedure may take several minutes, please be patient.

NOTE: Never interrupt the upgrade procedure by closing the web

browser or physically disconnect your computer from router. If the

ﬁrmware you uploaded is corrupt, the ﬁrmware upgrade will fail, and

you may have to return this router to the dealer of purchase to ask for

help.

English

17

Change management password

Default password of Wireless Router is “admin”, and it’s displayed on

the login prompt when accessed from web browser. There’s a security

risk if you don’t change the default password, since everyone can see

it. This is very important when you have wireless function enabled.

To change password, please follow the following instructions:

Please click ‘Management -> Management’ menu on the web

management interface, the following message will be displayed on

your web browser:

When you ﬁnish, click ‘Apply’; If you want to keep original password

unchanged, click ‘Reset’.

Svenska

18

Inledning

WSR 2.0 är en kombinerad fast / trådlös nätverksanslutningsenhet

som har utformats speciellt för nätverk på små företag, kontor och

hemmakontor. Den uppfyller IEEE 802.11n (Draft 2.0)-standard. Den

använder MIMO- samt SST-teknik. Det fungerar också bra med

andra trådlösa produkter som använder 11b/g och 111n-protokoll.

Du kan omedelebart upprätta WiFi-hotspots på en plats där du har

Internet-anslutning.

Medföljande tillbehör:

1 x WSR 2.0 Trådlös Router

1 x Snabbstartsguide

1 x Strömadapter

1 x RJ-45 Nätverkskabel

Svenska

19

Kom igång

Sätt upp ett trådlöst nätverk

Kabel / DSL-modem

Trådlös router

PC eller laptop

(Trådlös adapter krävs)

För ett vanligt trådlöst nätverk hemma (såsom på bilden ovan)

Gör följande:

1. Du kommer att behöva internet-åtkomst (exempelvis ADSL eller

bredband) till ditt hem eller kontor.

2. Du kan rådgöra med din internetleverantör för hur du ska

installera modem.

3. Anslut modemet till den trådlösa routern. Koppla in

strömadaptern till routern.

4. Koppla datorer till routern.

VIKTIGT

Du kan återställa routern till fabriksinställningar genom att trycka på

“RESET”-knappen på baksidan av routern. Du kan använda den här

lösningen om du har glömt lösenordet till routern.

Svenska

20

Lägg till datorer till routern

1. Logga in på din dator.

2. Öppna nätverksanslutningen genom att högerklicka på

nätverksikonen ( eller ) i meddelandefältet.

3. Välj det trådlösa nätverket i listan som visas och klicka sedan

på Anslut.

4. Ange nätverkssäkerhetsnyckel eller lösenordsfras om du blir

ombedd att göra det, och klicka sedan på OK.

Du kommer att få se ett bekräftelsemeddelande när du är

ansluten till nätverket.

För att bekräfta att du har lagt till datorn gör du så här:

Öppna Nätverk genom att klicka på Start-knappen , och klicka

sedan på Kontrollpanelen. I sökrutan skriver du nätverk, och sedan,

under Nätverks-och delningscenter, klicka på Visa datorer och

enheter.

Du bör se ikoner för den dator du lagt till och för andra datorer

och enheter som ingår i nätverket.

OBS: Om du inte ser ikoner i nätverksmappen, kan nätverk och

ﬁldelning kan vara avstängd.

För mer information:

http://windows.microsoft.com/sv-SE/windows7/Add-a-device-or-computer-to-

a-network

http://windows.microsoft.com/sv-SE/windows7/Setting-up-a-Wirelessetwork

http://windows.microsoft.com/sv-SE/windows-vista/Setting-up-a-

Wirelessetwork

Sidan laddas ...

Andersson WSR 2.0 Användarmanual

Andersson WSR 2.0 Användarmanual

på andra språk

Relaterade papper

Andra dokument