VDO CD1537X Användarmanual

4

3

2

1

5

6

DISP

REL

MODE

A/PS

MUTE RPT INT RND 10

+

10SCAN

AF/

REG

PTY

SCH

BAND

TA

MMC

LOUD

VOL

PUSH

SEL

CD 1737X

2

3

A

B

C

D E

16

15

14

13

12

11

10

1

2

3

4

5

6

7

8

9

1

2

3

4

5

F 15A

Lout

Ant.

Rout

Rin

Lin

AUX

4

F G

4

1

3

2

188

mm

58mm

1

2

1

3

4

I

H

5

J

1

2

A

B

3

L

M

K

6

7

INTRODUCTION

Before Starting

Thank you for purchasing this VDO Dayton

product which has been designed and manu-

factured according to applicable Safety Regula-

tions, following the highest standards and sub-

jected to rigorous testing. Kindly familiarise

yourself with the product by reading this user

manual carefully. Use the product as intended,

and keep this manual handy in your car for

future reference.

Environment

This booklet is printed on low-chlorine recycla-

ble paper.

PREVENTIVE MAINTENANCE

To ensure good connection between the set

and the detachable front, it is advisable to clean

the connectors with a cotton swab slightly

moistened with cleaning fluid or alcohol periodi-

cally.

CONTENT PAGE

INTRODUCTION ....................................... 7

Before Starting ......................................... 7

Environment ............................................ 7

PREVENTIVE MAINTENANCE .................. 7

CONTENT PAGE ....................................... 7

GENERAL INFORMATION ......................... 8

Disclaimer ............................................... 8

Class 1 Laser Product ............................ 8

FEATURES ................................................ 8

RDS (Radio Data System) ...................... 8

Notes on audio CDs ............................... 8

Notes on MP3 files .................................. 9

Notes on WMA files.................................. 9

Notes on OGG files ............................... 10

Notes on Folders................................... 10

Notes on Bluetooth® ............................. 11

INSTALLATION ....................................... 12

Installation ............................................. 12

Connection in vehicles equipped with

standard ISO connectors ...................... 12

Connection in vehicles without

standard ISO connectors ...................... 12

Preparation............................................ 12

Connectors (fig. C) ................................ 12

Electronic or Motorised Antenna ........... 12

MOUNTING ............................................. 13

Metal Sleeve (fig. F and G ).................... 13

Connecting the Radio (fig. C)................ 13

Mounting the Radio (fig. G and H)......... 13

Removing the Radio (using the two

removal keys supplied) (fig. J) .............. 13

Replacing the Fuse (fig. C) ................... 13

Interference Suppression ..................... 13

FRONT PANEL AND REMOTE CONTROL14

Front Panel Remote Control

Function(s) ............................................ 14

SECURITY .............................................. 15

Removing the Front (fig. A and I) ........... 15

Replacing the Front (Fig. K and L) ........ 15

GENERAL OPERATION .......................... 15

Switching On/Off .................................... 15

Setting the Start-up Volume ................... 15

Selecting a Source ................................ 15

Sound Controls ..................................... 15

RADIO OPERATION ................................ 16

Select a waveband ................................ 16

Select a station ...................................... 16

FM Stereo Operation (Remote Control

only) ....................................................... 16

Memorising Radio Stations................... 16

RADIO DATA SYSTEM (RDS) ................. 16

Display of Station Name (PS)................ 17

Automatic frequency (AF)....................... 17

Traffic Announcements (TA) .................. 17

Programme Type Selection (PTY)......... 17

CD OPERATION ...................................... 17

Loading CD in the CD player ................ 17

Pausing a CD ........................................ 17

Ejecting a CD......................................... 17

CD playback .......................................... 17

Compressed Audio playback ................ 17

Playing a CD-R or CD-RW .................... 18

Playing a “copy protected” non-

conforming audio CD ............................ 18

Listening to CD/MP3/WMA/OGG ........... 18

Track/File Selection ............................... 18

SD/MMC/USB OPERATION .................... 18

General.................................................. 18

Pausing ................................................. 18

File Selection ......................................... 18

8

BLUETOOTH® CAR UNIT ....................... 19

General.................................................. 19

Controls (fig. D) ..................................... 19

Pairing your cell phone and Bluetooth®

remote box............................................. 20

Answering an incoming call.................. 20

Re-dialling last called number.............. 20

Ending a call.......................................... 20

State of the LED on the Bluetooth® car

unit ......................................................... 20

TROUBLESHOOTING ............................. 21

Symptoms Cause/Remedy................... 21

GENERAL INFORMATION

Disclaimer

Designs and specifications are subject to

changes without prior notice.

Class 1 Laser Product

Any inappropriate use of the device may ex-

pose the user to invisible laser rays. Which

exceed the limits for Class 1 laser products.

Caution:

Any inappropriate use of the device may

expose the user to invisible laser rays.

Which exceed the limits for Class 1 laser

products.

Important Information

z Only trained specialists may install the sys-

tem.

z Observe the automotive industry quality stand-

ards.

z Fire hazard. During drilling, be careful not to

damage hidden cable harness, the fuel tank

and fuel lines.

z Never drill into supporting or safety-relevant

chassis parts.

It is essential to observe the following when

installing components in the passenger com-

partment:

z Ensure that the driver has a clear all-round

view.

z Increased risk of injury in the event of an ac-

cident. Do not install components in the infla-

tion range of the airbag or in areas where the

head or knees may knock against them.

z Do not damage cables of the safety systems

(airbag etc.). (Lines are normally specially

marked, e.g. by labels.)

z Do not use inspection lamps to test the volt-

age, since excessively high currents can dam-

age / destroy electronic components.

z Do not use any pinch or cut connectors. Sol-

der all cable connections. Insulate all solder

points with shrinkable hose or insulating tape.

z If there are earth connections on the chassis,

insert toothed washers. Remove paint and dirt

first, if necessary.

z Use only the parts included with the unit to

ensure proper installation. The use of unau-

thorized parts can cause malfunctions.

z Avoid installing the unit where it would be

subject to high temperature, such as from di-

rect sunlight, or from hot air, from the heater,

or where it would be subject to dust, dirt or

excessive vibration.

FEATURES

RDS (Radio Data System)

Many VHF stations transmit RDS information.

The navigation radio evaluates the RDS tel-

egram and offers the following advantages:

z PS (Program Service name): Display of sta-

tion name.

z Radio text: Display of additional information

concerning the radio station.

z PTY (Program TYpe): Station selection by pro-

gram type.

z AF (Alternative Frequency): Automatic re-tun-

ing to best alternative frequency.

z TA (Traffic Announcement): Traffic announce-

ments.

z EON (Enhanced Other Networks): Automatic

fade-in of traffic announcements of other sta-

tions.

z NEWS: Fading in of messages and items of

news.

Notes on audio CDs

You can play 12 cm CDs on your CD player.

The use of 8 cm CDs (with or without adapter)

and of CDs with irregular shapes is not recom-

mended.

CD formats

The following CD formats are supported by the

CD player:

z CD Audio (CD-DA in accordance with the Red

Book Standard);

A maximum of 22 CD Text titles is displayed in

the title list.

9

z CD-ROM (in accordance with Yellow Book)

z CD-ROM XA (mode 2, form 1, in accordance

with Green Book)

z CD-R/RW (in accordance with Orange Book,

part 2/3)

z CD Text with CD Audio (in accordance with

Red Book)

z CD Mixed Mode (in accordance with Light

Yellow Book);

Only the audio tracks are played.

z CD-Extra; Only the audio tracks are played.

z Multi-session CD (in accordance with multi-

session CD specification 1.0)

Notes on MP3 files

The following MP3 files are supported by the

CD player:

z Files conform with MPEG1/2 or 2.5-Layer 3.

z Up to 345 titles in up to 99 directories (each

data name with 32 characters).

z Bit rate: Maximum of 320 kbit/s, constant or

variable. The sound quality of MP3 files gen-

erally becomes better with an increased bit

rate. This unit can play recordings with bit

rates from 8 kbps to 320 kbps, but in order to

be able to enjoy sound of a certain quality, we

recommend using only discs recorded with a

bit rate of at least 128 kbps.

z Text display: ID3 tag V1 and ID3 tag V2. MP3

tracks can contain addition information such

as artist, track and album names (ID3 tags

with maximum not more than 12 characters).

Characters other than uppercase/lowercase

letters (“Aa to Zz”) and underscore (“_”) may

not be displayed.

z The unit may not play the first track in the

order that you wrote them to the disc.

z The unit plays only the first session if the disc

contains both CD audio tracks and MP3 files.

z When playing a disc of 8k bps or variable bit

rate (VBR), the elapsed playing time in the

display window may not be correct.

z Make sure that a MP3 CD-R/CD-RW is burned

that is formatted as a data disc and NOT as an

audio disc.

z MP3 files are not compatible with packet write

data transfer.

z There is no m3u play list compatibility.

z There is no compatibility with the MP3i (MP3

interactive) or mp3 PRO formats.

z The MP3 symbol will be shown in the display if

a MP3 is being played.

z Files are compatible with the ID3 Tag Ver. 1.0,

1.1, 2.2, 2.3 and 2.4 formats for display of

album (disc title), track (track title), artist (track

artist) and comments. Ver. 2.x of ID3 Tag is

given priority when both Ver. 1.x and Ver. 2.x

exist.

Notes on WMA files

z WMA is short for Windows Media ™ Audio and

refers to an audio compression technology that

is developed by Microsoft Corporation. WMA

data can be encoded by using Windows Media

Player version 9 or lower.

z This unit may not operate correctly depending

on the application used to encode WMA files.

z Depending on the version of Windows Media

Player used to encode WMA files, album names

and other text information

may not be correctly displayed.

z There may be a slight delay when starting

playback of WMA files encoded with image

data.

z The maximum number of characters which can

be displayed for a folder name is 64.

z In case of files recorded according to the

Romeo file system, only the first 64 characters

can be displayed.

z This unit plays back WMA files encoded by

Windows Media Player version 7, 7.1, 8 and 9.

z You can only play back WMA files in the

frequencies 32, 44.1 and 48 kHz.

z The sound quality of WMA files generally

becomes better with an increased bit rate. This

unit can play recordings with bit rates

from 48 kbps to 320 kbps (CBR) or from 48

kbps to 320 kbps (VBR), but in order to be able

to enjoy sound of a certain quality, we

recommend using discs recorded with a higher

bit rate.

This unit doesn’t support the following

formats.

z Windows Media Audio 9 Professional (5.1ch)

z Windows Media Audio 9 Lossless

z Windows Media Audio 9 Voice

10

Notes on OGG files

The following OGG files are supported by the

CD player:

z Files conform with Vorbis I specifications.

z Up to 99 titles in up to 99 directories (each

data name with 32 characters maximum).

z Bit rate: Maximum of 192 kbit/s encoding. The

sound quality of OGG files generally becomes

better with an increased bit rate. This unit can

play recordings with bit rates from 8 kbps to

192 kbps.

z Text display: *0.60 + 1em format (Vorbis I). OGG

information can contain information such as

title, artist, track-number, album name, version,

etc. Characters other than digits (“0 to 9”)

uppercase/lowercase letters (“Aa to Zz”) and

underscore (“_”) may not be displayed.

z The unit may not play the first track in the order

that you wrote them to the disc.

z The unit plays only the first session if the disc

contains both CD audio tracks and OGG files.

z When playing OGG files, the elapsed playing

time in the display window may not be correct.

z Make sure that a OGG CD-R/CD-RW is burned

that is formatted as a data disc and NOT as an

audio disc.

Important

z When naming a MP3/WMA/OGG file, add the

corresponding file name extension (.mp3,

.wma or .ogg).

z This unit plays back files with the file name

extension (.mp3, .wma or .ogg) as a MP3/

WMA/OGG file. To prevent noise and

malfunctions, do not use these extensions for

files other than MP3/WMA/OGG files.

z This unit allows playback of MP3/WMA/OGG

files on CD-ROM, CD-R and CD-RW discs. Disc

recordings compatible with level 1 and level 2

of ISO9660 and with the Romeo and Joliet file

system with sector format in Mode 1 or Mode

2 Form 1 can be played back. Other formats

cannot be played reliably.

z It is possible to play back multi-session com-

patible recorded discs.

z MP3/WMA/OGG files are not compatible with

packet write data transfer.

z The maximum number of characters which

can be displayed for a file name, including the

extension (.mp3, .wma or .ogg), is 64, from

the first character.

z When playing discs with MP3/WMA/OGG files

and audio data (CD-DA) such as CD-EXTRA

and MIXED-MODE CDs, both

types can be played only by switching mode

between MP3/WMA/OGG and CD-DA.

z The folder selection sequence for playback

and other operations becomes the writing

sequence used by the writing software. For

this reason, the expected sequence at the

time of playback may not coincide with the

actual playback sequence. However, there

also is some writing software which permits

setting of the playback order.

z Some audio CDs contain tracks that merge

into one another without a pause. When these

discs are converted to MP3/WMA/OGG files

and burned to a CD-R/CD-RW/CD-ROM, the

files will be played back on this player with a

short pause between each one, regardless

of the length of the pause between tracks on

the original audio CD.

Notes on Folders

z An outline of a CD-ROM with MP3/WMA/OGG

files on it is shown below. Sub folders are

shown as folders in the folder currently se-

lected.

L1 = Level 1 L2 = Level 2 L3 = Level 3

05

01

(ROOT)

02

03

04

(030.mp3/030.wma/030.ogg)

(021.mp3/021.wma/021.ogg)

(020.mp3/020.wma/020.ogg)

(011.mp3/011.wma/011.ogg)

(010.mp3/010.wma/010.ogg)

(001.mp3/001.wma/001.ogg)

L1

L2

L3

11

Notes

z This unit assigns folder numbers. The user

cannot assign folder numbers.

z It is not possible to check folders that do not

include MP3/WMA/OGG files. (These folders

will be skipped without displaying the folder

number.)

z MP3/WMA/OGG files in up to 8 tiers of folders

can be played back. However, there is a de-

lay in the start of playback on discs with nu-

merous tiers. For this reason we recommend

creating discs with no more than 2 tiers.

z It is possible to play back up to 99 folders on

one disc.

Notes on Bluetooth

®

Bluetooth

®

is a short-range wireless radio con-

nectivity technology used mainly for mobile

phones, hand-held PCs and other devices.

Bluetooth

®

operates in 2.4 GHz frequency

range and transmits voice and data at speeds

up to 1 megabit per second within a range of

about 10m (about 30 feet). Bluetooth

®

was

launched by a special interest group (SIG) that

comprises of Ericsson Inc., Intel Corp., Nokia

Corp., Toshiba and IBM in 1998.

z The Bluetooth

®

word mark and logos are

owned by the Bluetooth SIG, Inc. and any use

of such marks is under license. Other trade-

marks and trade names are those of their re-

spective owners.

Protecting your unit from theft

The front panel can be detached from the head

unit and stored in the provided protective case

to prevent theft.

z If the front panel is not detached from the head

unit within five seconds of turning off the igni-

tion, a warning tone will sound and the front

panel will open.

Important

z Never use force or grip the display and the

buttons too tightly when removing or attach-

ing.

z Avoid subjecting the front panel to excessive

shocks.

z Keep the front panel out of direct sunlight and

high temperatures.

z A few seconds after turning the ignition switch

to on or off, the front panel automatically

moves. When this happens, your fingers may

become jammed in the panel, so keep your

hands away from it.

CD player and care

z Use only CDs that have either of the two Com-

pact Disc Digital Audio marks as shown be-

low.

z Use only normal, round CDs. If you insert ir-

regular, non-round, shaped CDs they may jam

in the CD player or not play properly.

z Check all CDs for cracks, scratches or warp-

ing before playing. CDs that have cracks,

scratches or are warped may not play prop-

erly. Do not use such discs.

z Avoid touching the recorded (non-printed)

surface when handling the disc.

z Avoid leaving fingerprints on the CD when

removing it.

z Always store audio CDs in their protective

covers when not in use.

z Always ensure that CDs are clean and dry

before inserting.

z Keep discs out of direct sunlight and do not

expose the discs to high temperatures.

z Do not attach labels, write on or apply chemi-

cals to the surface of the discs.

z To clean a CD, wipe the disc with a soft cloth

outward from the centre.

z If the heater is used in cold weather, moisture

may form on components inside the CD player.

Condensation may cause the CD player to

malfunction. If you think that condensation is a

problem turn off the CD player for an hour or

so to allow it to dry out and wipe any damp

discs with a soft cloth to remove the moisture.

z Road shocks may interrupt CD playback.

12

Cleaning the unit

Do not clean using cleaning fluid, alcohol or

other solvents. Use only a damp cloth.

CD-R/CD-RW discs

z When CD-R/CD-RW discs are used, playback

is possible only for discs which have been

finalized.

z It may not be possible to play back CD-R/CD-

RW discs recorded on a music CD recorder or

a personal computer because of disc charac-

teristics, scratches or dirt on the disc, or dirt,

condensation, etc., on the lens of this unit.

z Playback of discs recorded on a personal

computer may not be possible, depending on

the application settings and the environment.

Please record with the correct format. (For

details, contact the manufacturer of the appli-

cation.)

z Playback of CD-R/CD-RW discs may become

impossible in case of direct exposure to sun-

light, high temperatures, or the storage condi-

tions in the vehicle.

z Titles and other text information recorded on a

CD-R/CD-RW disc may not be displayed by

this unit (in the case of audio data (CD-DA)).

z Read the precautions with CD-R/CD-RW discs

before using them.

INSTALLATION

Use the supplied mounting sleeve and the strap

bracket to mount the car radio firmly in the

dashboard.

Only use the supplied screws and nets for

installation.

Keep leftover installation equipment for future

use.

If the installation requires drilling of holes or

other modifications to the vehicle, contact your

nearest dealer.

This set is designed for the installation in the

radio space in the dashboard.

Installation

1. If the space is to small, enlarge it as shown in

figure F.

2. Install the sleeve in the dashboard (see fig-

ure G).

z Slide the sleeve in the dashboard.

z Push the tabs down with a screw driver.

3. Insert the radio into the sleeve.

4. Connect the cables as shown in figure C.

5. Attach the bracket to the radio and mount it

an the chassis (see figure H).

Connection in vehicles equipped

with standard ISO connectors

The radio may be installed without major prepa-

ration in vehicles equipped with ISO connec-

tors. Some signals may have to be adapted or

connected to the ISO connectors.

Connection in vehicles without

standard ISO connectors

For vehicles with different connection require-

ment, ask your dealer for an adaptor cable. If

no adaptor cable is available for your vehicle,

connect the radio as describe in the "Connec-

tors" section.

Preparation

The device must be connected to a 12V DC

electrical system with a negative terminal to

earth (car chassis).

Warning: Installation that does not con-

form to these requirements may result in

malfunction, damage or fire!

To avoid the risk of a short circuit during instal-

lation, disconnect the negative terminal of the

battery until the set has been securely installed

and connected.

Connectors (fig. C)

Connector A

1

)

a- Power Supply

1 Yellow/red wire A4: Connect to the switched

12V supply (switched on/off by the car igni-

tion.

2 Red wire A7: Connect to a permanent 12V

supply. This is the main power supply.

Ensure that this connection can handle a

current of 15A.

3 Brown wire A8: Connect to earth (car chas-

sis).

Electronic or Motorised Antenna

Connect pin A5 to the power supply for an

electronic antenna or the control wire for the

relay of an automatic motorised antenna.

Do not use this connection for direct power

supply to the antenna motor.

13

Connector B

1

)

Loudspeakers (use 4 ohm loudspeakers only)

Do not connect any of the loudspeaker leads to

earth or directly to a booster/amplifier without

high level input or via an external fader! You

can connect the loudspeaker leads directly to

an amplifier with high level input:

Connecting 4 loudspeakers

Side & pol. Front/colour Pin Rear/colour Pin

Left (+) Green [B5] White [B7]

Left (-) Green/black [B6] White/black [B8]

Right (+) Grey [B3] Blue [B1]

Right (-) Grey/black [B4] Blue/black [B2]

1

) For this accessory, contact your dealer.

Line out

You can connect a power amplifier with 2 or 4

additional loudspeakers to this set using the

labelled RCA cable.

z Red socket to right channel

z White socket to left channel.

Audio In

You can connect external audio equipment via

the labelled AUX-in RCA cables.

z Red wire for Right Channel input

z White wire for Left Channel input.

MOUNTING

Metal Sleeve (fig. F and G )

Install the metal sleeve in the dashboard. For

optimal performance of the CD player, the metal

sleeve should be positioned horizontally (be-

tween -10° and +30°).

Fix metal sleeve into place by pressing the

metal tags outwards using a screwdriver.

Connecting the Radio (fig. C)

z Ensure the battery is disconnected.

z Insert power supply connector A’ into socket

A.

z Insert loudspeaker connector B’ into socket B.

z (Optional) Insert the line-out connector into the

corresponding socket.

z (Optional) Insert the AUX connector into the

corresponding socket.

z Insert aerial plug into the aerial socket (good

reception is only possible with a good aerial).

If an antenna adaptor is needed, please con-

sult your dealer.

Mounting the Radio (fig. G and H)

This radio can be properly installed either from

conventional Front Mounting and/or from Rear

Mounting.

Front Mounting

z Slide the radio into the metal sleeve until the

springs at either side of the radio snap into the

openings of the sleeve.

z Finally reconnect the negative car battery ter-

minal.

Rear Mounting

z Choose a position where the screw holes of

the mounting bracket and the screw holes of

the radio become aligned and tighten the

screws at 2 places on each side.

z Only use M5 screws that are not longer than

6 mm.

Removing the Radio (using the two

removal keys supplied) (fig. J)

z Press the REL button and open the front panel.

z Insert both removal keys into the holes on the

front of the set until they lock.

z Pull out the radio.

Replacing the Fuse (fig. C)

z Replace with a 15A blade-type fuse.

The new fuse must be of exactly this value and

type otherwise the set will not be adequately

protected. Ignoring this procedure may lead to

damage to the set, which will invalidate the

guarantee.

Interference Suppression

Most modern cars have sufficient interference

suppression. If you experience interference

generated by the car, consult your dealer.

14

FRONT PANEL AND REMOTE

CONTROL

See fig. A and E.

Front Panel Remote Control

Function(s)

1. 1. Switch On / Off the set

2.

PTY

10. Select stations by program

type

3.

BAND/ENT

3. Change FM/AM band/

Enter (in function

selection)

4.

TA

9. Activate/deactivate Traffic

Announcement Search

5. M1...M6 16. Radio:

Short press: recall

memorised radio

stations

Long press: store

selected radio

stations

SD/MMC/USB/CD:

Press to activate

special control functions

(Play/Pause, Repeat,

Introduce (10 sec.),

Random, Skip 10 tracks

back, Skip 10 tracks

forward)

6. AF/REG 8. Toggle AF-

REGionalisation

7. 13. Radio:

Short press: auto-seek a

station (auto mode)/

stop the frequency

(manual mode)

Long press:

activate manual tuning

mode

SD/MMC/USB/CD:

Short press: select

the previous or next

track/file

Long press: Review/

Fast-forward the current

track

8. DISP 5. Toggle the display modes

9.

VOL/SEL

15. Turn: increase/decrease

volume

Short press: select sound

controls (VOLume,

BALance, FADer)

Long press: select special

functions (Start IN,

VOLume, Time ADJust,

TA VOLume, EON,

DSP None/Classic/Rock/

Pop/Flat)

10.

USB Port

Port for inserting USB

devices

11.

SD/MMC Slot

Slot for inserting Flash

Memory Cards

12. Mute 12. Mute/demute audio level

13.

SCH/A/PS

4. Radio:

Short press: Scan the 6

preset radio stations for 5

sec. per station

Long press: Search and

store six radio stations

SD/MMC/USB/CD:

Activate track/file search

(song selection mode)

14. MODE 2. Change source between

the FM/AM, CD, USB, SD/

MMC and Auxiliary modes

16.

CD Load Slot

Slot to load/unload CD

17.

EJECT Button

Eject/reload CD

18.

LCD Screen

Shows all information and

functions

19.

REMOTE CONTROL

Receives signal from the

Sensor

IR Remote Control

20.

RESET Button

Reset if the unit is

malfunctioning

21.

SCAN / LOUD

6. Short Press: scan for a

radio station broadcast for

5 sec. then scan for the

next station, press again

to stop

Long Press: toggle

loudness

15

7. Short press: select Mono/

Stereo

Long press: select Local/

Distant Reception

11. Toggle sound equalization

14. Increase/decrease

volume

SECURITY

Removing the Front (fig. A and I)

1. Press the REL key, to flip-down the front.

2. Pull the front towards you. Follow the dia-

gram mounted on the back of the detachable

unit.

3. Take the detachable front with you when you

leave the car.

4. Keep the front in its protective cover.

Replacing the Front (Fig. K and L)

1. Take the front from its protective cover.

2. Insert the front into radio until it clicks into

position.

3. Close the front until it clicks into position.

Note 1:

If you hear a warning signal, the front is not

properly replaced!

Note 2:

To ensure good connection between the set

and the detachable unit, it is advisable to clean

frequently the connections with a cotton swab

from time to time!

Note 3:

Do not touch the electrical contacts when re-

moving or replacing the front panel!

GENERAL OPERATION

Switching On/Off

Press button to switch the set on or off.

Setting the Start-up Volume

1. Long press the VOL/SEL knob to enter the

special functions mode.

2. Press the knob till you see "IN VOL XX", where

"XX" is the starting volume.

3. Turn the knob to adjust the IN VOL to a com-

fortable level.

Note: If the radio was previously at a higher

volume level when you turned off the radio:

After you turn on the radio, the radio will use

the starting volume. Otherwise the radio will

remember the previous volume level.

Selecting a Source

Your car radio is designed for different types

of sources.

z RADIO

z CD

z USB

z SD/MMC

z AUX

Press the MODE button to select the source.

Sound Controls

Volume

Please make sure you can still hear the traffic

(horns, sirens..….)

z Turn the volume knob to adjust the volume.

Note: You can adjust the start-up volume (IN

VOL). When the start-up volume is set to maxi-

mum level, it may be extremely loud when you

switch on the set.

See: Setting the Start-up Volume

Balance

To change the balance between the amount of

sound output on the left and right side.

1. Press the VOL/SEL knob to select the sound

control Balance (BAL).

2. Turn the knob to adjust the level of sound

output to the left and right speakers.

Bass (only when DSP is off)

To change the enhancement of low frequency.

1. Press the VOL/SEL knob to select the sound

control Bass (BAS).

2. Turn the knob to adjust the level of bass en-

hancement.

Treble (only when DSP is off)

To change the enhancement of high frequency.

1. Press the VOL/SEL knob to select the sound

control Treble (TRE).

2. Turn the knob to adjust the amount of treble

enhancement.

Fader

To change the amount of sound output to the

front and rear speakers.

1. Press the VOL/SEL knob to select the sound

control Fader (FAD).

2. Turn the knob to adjust the level of sound

output to the front and rear speakers.

16

Equalizer

Press the EQ button on the remote control to

select one of the programmed equalizer set-

tings.

z None (NONE)

z Classic (CLAS)

z Rock (ROCK)

z Pop (POP)

z Flat (FLAT)

Mute

Press the Mute button to mute the sound. If a

CD is playing, it will be paused. Press the Mute

button again to restore the sound and the CD

will continue playing.

Loudness

Radio and Remote Control

Long press the Loud button to enhance the

high and low frequency sound quality.

RADIO OPERATION

1. Press the button to switch the set on.

If the set is not in RADIO mode:

2. Press the MODE button to select RADIO.

Select a waveband

Your radio is designed for reception of the FM

and AM wavebands.

z FM 1

z FM 2

z FM 3

z AM 1

z AM 2

Press the BAND/ENTER button to select the

desired radio band.

Select a station

Seek tuning

Press button (frequency down) or

(frequency up) to seek for a station. The tuner

will scan down or up to the next strong station.

Manual Tuning

Long press either one of the buttons or

to select manual tuning.

Press button (frequency down) or

(frequency up) until the desired radio station is

selected. If there is no further action for 10

sec., the radio will switch back to auto tuning

mode.

Auto Store

Long press the SCH/ A /PS button, the radio will

search for the six strongest stations and store

them automatically under the preset memory

buttons 1 through 6.

Scan (Remote Control only)

This function allows you to scan the stations or

the presets of the current band.

Short Press the SCAN button and the radio will

start scanning.

When it receives a radio signal, the screen will

flash 10 times and show the reception fre-

quency. The radio will continue scanning using

this pattern.

When the desired station is reached, press the

SCAN button again to stop scanning.

Preset Scan

Short Press the SCH/ A /PS button, the radio

pauses for 5 sec. at each preset station. When

the desired station is reached, press the button

again to select this station.

FM Stereo Operation (Remote

Control only)

If the stereo signal becomes to weak (bad re-

ception of the radio station):

1. Press the ST/LOC button on the remote con-

trol until MONO appears in the display of the

radio.

2. Press this button again and STEREO appears

in the radio display.

Memorising Radio Stations

1. Press the Band Button to select the desired

band, FM1, FM2, FM3, AM1 or AM2.

2. Tune in the desired radio station.

3. Long press any of the 6 Preset buttons to

store the radio station. The number will be

displayed next to the radio frequency. For

each band you can store up to six radio sta-

tions.

RADIO DATA SYSTEM (RDS)

This feature is only available with the FM band!

Many FM stations broadcast RDS information.

All RDS related features e.g. TA, NEWS etc...

will be deactivated when option ‘RDS’ is set to

‘OFF’.

This set uses the RDS information to offer you

many advantages including:

17

Display of Station Name (PS)

The radio displays the name of the station in-

stead of its frequency.

Automatic frequency (AF)

The set remains tuned to the current station by

continually searching for the best possible al-

ternative frequency for reception.

Note: The AF function is preset. You can

switch off AF if not required. Press the AF/REG

button and select OFF.

Traffic Announcements (TA)

You can activate the TA mode to give priority to

hear announcements related to these subjects

(even if you do not listen to the radio).

This function is only available with RDS on.

Presetting TA Volume

With this option the volume for Traffic An-

nouncements can be preset to the required

level.

1. Long press the knob to select the TA VOL

setting.

2. Turn the VOL knob clockwise to set volume

“louder” and counter-clockwise “softer” de-

pending on your requirements.

Activate/deactivate TA

Press TA button to activate/deactivate TA.

When traffic announcement is selected and

information is received TP appears in the dis-

play.

Interrupting Traffic Announcement

If you do not wish to continue listening to a

particular Traffic Announcement mode, you can

interrupt it without switching off the mode.

1. Press TA button once, the set will return to

the previous operating mode.

Note: You can switch off RDS features if not

required.

2. Press the AF/REG button and select the op-

tion OFF.

Programme Type Selection (PTY)

This function is available with FM only. It ena-

bles you to select stations by programme type.

There is a coding of up to 28 pre-defined pro-

gramme types – e.g. (in Europe): PTY1 News,

PTY6 Drama, PTY11 Rock music.

1. Short press this button to display the PTY

information, the display is flashing.

2. Press either the or button to search

for PTY stations.

3. Long press the PTY button to display the pro-

gramme type. Turn the VOL knob to select

the programme required.

4. Press the PTY button again to confirm the

selection.

CD OPERATION

Loading CD in the CD player

1. Press the button to switch the set on.

2. Press REL button to open the front.

3. Insert the CD (label facing up) into the CD

slot.

When a disk is loaded it will be played auto-

matically.

Note: If a CD does not automatically load, DO

NOT FORCE it into the slot, this could damage

the CD and the set.

4. Close the front.

Pausing a CD

Radio:

1. Short press the to pause or resume play-

ing.

Remote Control:

1. Long press the on the remote control to

pause or resume playing.

Ejecting a CD

1. Press REL to open the front.

2. Press the EJECT button to eject the CD.

3. Remove the disc.

4. Close the front.

CD playback

This CD player is suitable only for 12 cm disc

and can read both audio and MP3/WMA/OGG

format CD. Please do not use irregular shaped

CD.

Compressed Audio playback

You are able to listen to MP3 files that conform

to MPEG1/2 & 2.5-Layer 3 at bit rate up to 320

kbps or Variable Bit Rate (VBR) burned with ID3

tag. You are also able to listen to WMA files that

conform to version 9 or below at bit rate up to

320 kbps and OGG files that conform to Vorbis I

at bit rate up to 128 kbps. The files can be

burned on a CD-R or CD-RW disc in ISO9660

level 1 and 2 format are also supported.

18

Playing a CD-R or CD-RW

Depending on the type of CD-R/CD-RW CD,

surface condition of the disc, as well as the

performance and condition of the CD writer,

certain CD-R/CD-RW CD may not operate nor-

mally on this unit.

Playing a “copy protected” non-

conforming audio CD

Due to use of copy protection schemes of

some audio CDs, which are non-conformance

to international audio CDs standards (Red

Book), these type of copy protected disc(s)

may not play on this set.

Listening to CD/MP3/WMA/OGG

If the first track is a data track, the disc will be

treated as MP3/WMA/OGG disc. (If no MP3/

WMA/OGG file was found throughout the disc,

then it will treat as audio disc). If first track is

an audio track, the disc will be treated as audio

disc.

If TA are set to ON, announcements will inter-

rupt CD playback.

Track/File Selection

Track Advance

1. Short press the or button to skip to

the next track or file, forward or backward.

Fast Forward

1. Long press the or button to skip to

fast forward or backward the track or file,

once it reaches the next track or file the fast

forward function is terminated.

Repeating a Track or File

To continually repeat the current track.

1. Long press the RPT (REPEAT) button to re-

peat the track/file currently playing.

Random Feature

1. Long press the RDM (RANDOM) button to play

the tracks or files in random order.

Intro Feature

1. Long press the INT button to scan the track

or files. Each track or file will be played for 10

seconds.

To stop scanning, press the button again and

the current track or file will be played.

Skipping Track or Files

1. Long press the –10 button to skip backward

10 tracks or files.

2. Long press the +10 button to skip forward 10

tracks or files.

Select a Track or File

1. Long press the SCH A/PS button.

2. Use the VOL knob (radio) or buttons (remote

control) to select the desired track or file.

3. Long press the ENTER button to play the se-

lected track or file.

SD/MMC/USB OPERATION

General

You can use the smart card or multimedia card

or an USB device to play music files.

1. Press the button to switch the set on.

2. Insert the USB device into the USB port or the

SD/MMC card into the SD card slot.

When an USB device or SD/MMC card is in-

serted it will be played automatically.

Pausing

Radio:

1. Short press the to pause or resume play-

ing.

Remote Control:

2. Long press the (Pause) button on the re-

mote control to pause or resume playing.

File Selection

File Advance

1. Short press the or button to skip to

the next file, forward or backward.

Fast Forward / Review

1. Long press the or button to skip to

fast forward or backward the file, once it

reaches the next file the fast forward func-

tion is terminated.

Repeating a File

To continually repeat the current track.

1. Long press the RPT (REPEAT) button to re-

peat the file currently playing.

Random Feature

1. Long press the RDM (RANDOM) button to play

the files in random order.

19

Intro Feature

1. Long press the INT button to scan the files.

Each file will be played for 10 seconds.

2. To stop scanning, press the button again and

the current file will be played.

Skipping Files

1. Long press the –10 button to skip backward

10 files.

2. Long press the +10 button to skip forward 10

files.

Select a File

1. Long press the SCH A/PS button.

2. Use the VOL knob (radio) or buttons (remote

control) to select the desired file.

3. Long press the ENTER button to play the se-

lected file.

Search for File Name/Title

To search for a file name or a title (using 3 let-

ters) follow the procedure below.

1. Press the SCH A/PS button twice. AÄÄwill

appear in the display.

2. Turn the VOLUME knob to select the first let-

ter.

3. Press the VOLUME knob to enter the first

letter.

4. Turn the VOLUME knob to select the second

letter.

5. Press the VOLUME knob to enter the second

letter.

6. Turn the VOLUME knob to select the third

letter.

7. Press the BAND/ENT button to search for the

file name.

8. If more than one name or title has the same

letters turn the VOLUME knob to select the

desired name or title.

9. Long press the BAND/ENT button to start play-

back.

Root Search for Directories

1. Press the SCH/A/PS/ button three times.

ROOT/ will appear in the display.

2. Turn the VOL/SEL knob to select the direc-

tory.

3. Press the BAND/ENT button to playback the

first song in the selected directory.

Interrupt play

1. Press the "1"/PLAY (PLAY/PAUSE) button to

pause the track being played.

In pause mode the display is flashing.

2. Press the "1"/PLAY (PLAY/PAUSE) button

again to or resume playing.

Important Notes on SD/MMC/USB

z The unit can read up to 2 Gb.

Smart Card or Multimedia Card

Insert the flash memory card into the SD/MMC

slot on the front of the set.

Notes:

z This unit may not play all SD cards with lock

function.

z Some SD/MMC devices may not operate cor-

rectly using this unit.

z This unit is not responsible any data loss.

Please backup your data!

USB Stick

Plug in the USB device into the USB port on the

front of the set.

Notes:

z This unit can connect to MP3 player/USB de-

vice (Microsoft® Windows

TM

System only).

z This unit can direct search the *.MP3 file in the

USB device.

z This unit can support WMA files.

z This unit can play the 48K byte - 320K byte

rate music files.

z This unit cannot operate some special USB

devices, e.g.. Mac system or security lock sys-

tems.

z Some USB devices may not operate correctly.

BLUETOOTH

®

CAR UNIT

(Available on CD1737X only)

General

You can use the Bluetooth

®

car unit in your car

to call hands free.

To do so, you have to connect your cellular

phone (must have the Bluetooth

®

function) by

pairing to the Bluetooth

®

car unit.

Controls (fig. D)

1. VOL+ increase the volume

2. LED shows that the cellular phone is

connected

3. TALK press to accept /to reject a call

4. MIC microphone to talk with the other

party

5. VOL- decrease the volume

20

Pairing your cell phone and

Bluetooth

®

remote box

1. Press the VOL+ on the Bluetooth

®

remote box.

The LED on the remote box will start flashing

fast, the pairing mode is activated.

z Refer to cell phone’s user manual to learn

who to put your cell phone into pairing

mode.

z The default PIN is 0000

2. After pairing, the LED on the car unit will flash

every 3 or 4 seconds to indicate that the unit

is in call waiting mode for receiving and mak-

ing calls.

Answering an incoming call

1. The ring tone will sound from the car radio

speaker.

2. Short press the TALK button to answer the

call.

3. Now you can talk hands free via the micro-

phone of the Bluetooth

®

car unit and listen

from the car audio speaker instead of your

cellular phone.

During talking, the LED on the Bluetooth

®

car

unit light continuously.

4. You can adjust the volume by means of the

VOL+ and VOL- button on the car radio.

5. To receive a call directly on your cell phone,

press the TALK button longer then 3 sec-

onds.

Re-dialling last called number

1. In call waiting mode, press the TALK button

twice, the last called number will be re-di-

alled.

Ending a call

1. Press the TALK button once and the Blue-

tooth

®

car unit will return to the call waiting

mode.

State of the LED on the Bluetooth

®

car unit

State LED Status

Pairing flashes fast

Not connected Off

Connected Lights every 4 sec. for

2 sec.

Ringing Lights continuously

Talking Lights continuously

Note:

The Bluetooth

®

compatibility depends on the

solution integrated into the Bluetooth

®

car unit

and the cell phone to be paired with. The

firmware of the cell phone may vary from re-

gion to region and manufacturer to manufac-

turer.

Sidan laddas ...

VDO CD1537X Användarmanual

Denna manual är också lämplig för

VDO CD1537X Användarmanual

på andra språk

Relaterade papper

Andra dokument