Yamaha RX-V1700 Användarmanual

Kategori
AV-mottagare
Typ
Användarmanual
YAMAHA ELECTRONICS CORPORATION, USA
6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.
YAMAHA CANADA MUSIC LTD.
135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA
YAMAHA ELECTRONIK EUROPA G.m.b.H.
SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, GERMANY
YAMAHA ELECTRONIQUE FRANCE S.A.
RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE
YAMAHA ELECTRONICS (UK) LTD.
YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD18 7GQ, ENGLAND
YAMAHA SCANDINAVIA A.B.
J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN
YAMAHA MUSIC AUSTRALIA PTY, LTD.
17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA
©
2006 All rights reserved.
RX-V1700
Printed in Malaysia WH63550
RX-V1700
AV Receiver
OWNER’S MANUAL
U
RX-V1700_U-cv.fm Page 1 Monday, May 8, 2006 3:54 PM
IMPORTANT SAFETY INSTRUCTIONS
i
Explanation of Graphical Symbols
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert you to the
presence of uninsulated “dangerous voltage” within
the product’s enclosure that may be of sufficient
magnitude to constitute a risk of electric shock to
persons.
The exclamation point within an equilateral triangle
is intended to alert you to the presence of important
operating and maintenance (servicing) instructions in
the literature accompanying the appliance.
1 Read Instructions – All the safety and operating instructions
should be read before the product is operated.
2 Retain Instructions – The safety and operating instructions
should be retained for future reference.
3 Heed Warnings – All warnings on the product and in the
operating instructions should be adhered to.
4 Follow Instructions – All operating and use instructions
should be followed.
5 Cleaning – Unplug this product from the wall outlet before
cleaning. Do not use liquid cleaners or aerosol cleaners.
6 Attachments – Do not use attachments not recommended by
the product manufacturer as they may cause hazards.
7 Water and Moisture – Do not use this product near water –
for example, near a bath tub, wash bowl, kitchen sink, or
laundry tub; in a wet basement; or near a swimming pool;
and the like.
8 Accessories – Do not place this product on an unstable cart,
stand, tripod, bracket, or table. The product may fall,
causing serious injury to a child or adult, and serious
damage to the product. Use only with a cart, stand, tripod,
bracket, or table recommended by the manufacturer, or sold
with the product. Any mounting of the product should
follow the manufacturer’s instructions, and should use a
mounting accessory recommended by the manufacturer.
9 A product and cart combination should be moved with care.
Quick stops, excessive force, and uneven surfaces may
cause the product and cart combination to
overturn.
10 Ventilation – Slots and openings in the cabinet are provided
for ventilation and to ensure reliable operation of the
product and to protect it from overheating, and these
openings must not be blocked or covered. The openings
should never be blocked by placing the product on a bed,
sofa, rug, or other similar surface. This product should not
be placed in a built-in installation such as a bookcase or rack
unless proper ventilation is provided or the manufacturer’s
instructions have been adhered to.
11 Power Sources – This product should be operated only from
the type of power source indicated on the marking label. If
you are not sure of the type of power supply to your home,
consult your product dealer or local power company. For
products intended to operate from battery power, or other
sources, refer to the operating instructions.
12 Grounding or Polarization – This product may be equipped
with a polarized alternating current line plug (a plug having
one blade wider than the other). This plug will fit into the
power outlet only one way. This is a safety feature. If you
are unable to insert the plug fully into the outlet, try
reversing the plug. If the plug should still fail to fit, contact
your electrician to replace your obsolete outlet. Do not
defeat the safety purpose of the polarized plug.
13 Power-Cord Protection – Power-supply cords should be
routed so that they are not likely to be walked on or pinched
by items placed upon or against them, paying particular
attention to cords at plugs, convenience receptacles, and the
point where they exit from the product.
14 Lightning – For added protection for this product during a
lightning storm, or when it is left unattended and unused for
long periods of time, unplug it from the wall outlet and
disconnect the antenna or cable system. This will prevent
damage to the product due to lightning and power-line
surges.
15 Power Lines – An outside antenna system should not be
located in the vicinity of overhead power lines or other
electric light or power circuits, or where it can fall into such
power lines or circuits. When installing an outside antenna
system, extreme care should be taken to keep from touching
such power lines or circuits as contact with them might be
fatal.
16 Overloading – Do not overload wall outlets, extension
cords, or integral convenience receptacles as this can result
in a risk of fire or electric shock.
17 Object and Liquid Entry – Never push objects of any kind
into this product through openings as they may touch
dangerous voltage points or short-out parts that could result
in a fire or electric shock. Never spill liquid of any kind on
the product.
18 Servicing – Do not attempt to service this product yourself
as opening or removing covers may expose you to
dangerous voltage or other hazards. Refer all servicing to
qualified service personnel.
19 Damage Requiring Service – Unplug this product from the
wall outlet and refer servicing to qualified service personnel
under the following conditions:
a) When the power-supply cord or plug is damaged,
b) If liquid has been spilled, or objects have fallen into the
product,
c) If the product has been exposed to rain or water,
IMPORTANT SAFETY INSTRUCTIONS
CAUTION
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
01EN_00_RX-V1700_U.book Page i Tuesday, June 27, 2006 9:37 AM
IMPORTANT SAFETY INSTRUCTIONS
ii
EXAMPLE OF ANTENNA GROUNDING
MAST
GROUND
CLAMP
ANTENNA
LEAD IN
WIRE
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810–20)
GROUNDING CONDUCTORS
(NEC SECTION 810–21)
GROUND CLAMPS
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250. PART H)
ELECTRIC
SERVICE
EQUIPMENT
NEC – NATIONAL ELECTRICAL CODE
d) If the product does not operate normally by following
the operating instructions. Adjust only those controls
that are covered by the operating instructions as an
improper adjustment of other controls may result in
damage and will often require extensive work by a
qualified technician to restore the product to its normal
operation,
e) If the product has been dropped or damaged in any
way, and
f) When the product exhibits a distinct change in
performance - this indicates a need for service.
20 Replacement Parts – When replacement parts are required,
be sure the service technician has used replacement parts
specified by the manufacturer or have the same
characteristics as the original part. Unauthorized
substitutions may result in fire, electric shock, or other
hazards.
21 Safety Check – Upon completion of any service or repairs to
this product, ask the service technician to perform safety
checks to determine that the product is in proper operating
condition.
22 Wall or Ceiling Mounting – The unit should be mounted
to a wall or ceiling only as recommended by the
manufacturer.
23 Heat – The product should be situated away from heat
sources such as radiators, heat registers, stoves, or other
products (including amplifiers) that produce heat.
24 Outdoor Antenna Grounding – If an outside antenna or
cable system is connected to the product, be sure the antenna
or cable system is grounded so as to provide some
protection against voltage surges and built-up static charges.
Article 810 of the National Electrical Code, ANSI/NFPA 70,
provides information with regard to proper grounding of the
mast and supporting structure, grounding of the lead-in wire
to an antenna discharge unit, size of grounding conductors,
location of antenna discharge unit, connection to grounding
electrodes, and requirements for the grounding electrode.
Note to CATV system installer:
This reminder is provided to call the CATV system
installer’s attention to Article 820-40 of the NEC that
provides guidelines for proper grounding and, in
particular, specifies that the cable ground shall be
connected to the grounding system of the building, as
close to the point of cable entry as practical.
FCC INFORMATION (for US customers)
1 IMPORTANT NOTICE: DO NOT MODIFY THIS
UNIT!
This product, when installed as indicated in the
instructions contained in this manual, meets FCC
requirements. Modifications not expressly approved by
Yamaha may void your authority, granted by the FCC, to
use the product.
2 IMPORTANT: When connecting this product to
accessories and/or another product use only high quality
shielded cables. Cable/s supplied with this product MUST
be used. Follow all installation instructions. Failure to
follow instructions could void your FCC authorization to
use this product in the USA.
3 NOTE: This product has been tested and found to comply
with the requirements listed in FCC Regulations, Part 15
for Class “B” digital devices. Compliance with these
requirements provides a reasonable level of assurance that
your use of this product in a residential environment will
not result in harmful interference with other electronic
devices.
This equipment generates/uses radio frequencies and, if
not installed and used according to the instructions found
in the users manual, may cause interference harmful to the
operation of other electronic devices.
Compliance with FCC regulations does not guarantee that
interference will not occur in all installations. If this
product is found to be the source of interference, which
can be determined by turning the unit “OFF” and “ON”,
please try to eliminate the problem by using one of the
following measures:
Relocate either this product or the device that is being
affected by the interference.
Utilize power outlets that are on different branch (circuit
breaker or fuse) circuits or install AC line filter/s.
In the case of radio or TV interference, relocate/reorient
the antenna. If the antenna lead-in is 300 ohm ribbon lead,
change the lead-in to coaxial type cable.
If these corrective measures do not produce satisfactory
results, please contact the local retailer authorized to
distribute this type of product. If you can not locate the
appropriate retailer, please contact Yamaha Electronics
Corp., U.S.A. 6660 Orangethorpe Ave, Buena Park, CA
90620.
The above statements apply ONLY to those products
distributed by Yamaha Corporation of America or its
subsidiaries.
01EN_00_RX-V1700_U.book Page ii Tuesday, June 27, 2006 9:37 AM
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.
iii
1 To assure the finest performance, please read this manual
carefully. Keep it in a safe place for future reference.
2 Install this sound system in a well ventilated, cool, dry, clean
place – away from direct sunlight, heat sources, vibration,
dust, moisture, and/or cold. Allow ventilation space of at least
30 cm on the top, 20 cm on the left and right, and 20 cm on
the back of this unit.
3 Locate this unit away from other electrical appliances, motors,
or transformers to avoid humming sounds.
4 Do not expose this unit to sudden temperature changes from
cold to hot, and do not locate this unit in an environment with
high humidity (i.e. a room with a humidifier) to prevent
condensation inside this unit, which may cause an electrical
shock, fire, damage to this unit, and/or personal injury.
5 Avoid installing this unit where foreign objects may fall onto
this unit and/or this unit may be exposed to liquid dripping or
splashing. On the top of this unit, do not place:
Other components, as they may cause damage and/or
discoloration on the surface of this unit.
Burning objects (i.e. candles), as they may cause fire,
damage to this unit, and/or personal injury.
Containers with liquid in them, as they may fall and liquid
may cause electrical shock to the user and/or damage to
this unit.
6 Do not cover this unit with a newspaper, tablecloth, curtain,
etc. in order not to obstruct heat radiation. If the temperature
inside this unit rises, it may cause fire, damage to this unit,
and/or personal injury.
7 Do not plug in this unit to a wall outlet until all connections
are complete.
8 Do not operate this unit upside-down. It may overheat,
possibly causing damage.
9 Do not use force on switches, knobs and/or cords.
10 When disconnecting the power cable from the wall outlet,
grasp the plug; do not pull the cable.
11 Do not clean this unit with chemical solvents; this might
damage the finish. Use a clean, dry cloth.
12 Only voltage specified on this unit must be used. Using this
unit with a higher voltage than specified is dangerous and may
cause fire, damage to this unit, and/or personal injury.
YAMAHA will not be held responsible for any damage
resulting from use of this unit with a voltage other than
specified.
13 To prevent damage by lightning, keep the power cord and
outdoor antennas disconnected from a wall outlet or the unit
during a lightning storm.
14 Do not attempt to modify or fix this unit. Contact qualified
YAMAHA service personnel when any service is needed. The
cabinet should never be opened for any reasons.
15 When not planning to use this unit for long periods of time
(i.e. vacation), disconnect the AC power plug from the wall
outlet.
16 Install this unit near the AC outlet and where the AC power
plug can be reached easily.
17 Be sure to read the “TROUBLESHOOTING” section on
common operating errors before concluding that this unit is
faulty.
18 Before moving this unit, press MASTER ON/OFF to release it
outward to the OFF position to turn off this unit, the main
room, Zone 2 and Zone 3 and then disconnect the AC power
plug from the AC wall outlet.
19 VOLTAGE SELECTOR (Asia and General models only)
The VOLTAGE SELECTOR on the rear panel of this unit
must be set for your local main voltage BEFORE plugging
into the AC wall outlet. Voltages are:
Asia model ............................ 220/230–240 V AC, 50/60 Hz
General model ........ 110/120/220/230–240 V AC, 50/60 Hz
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN
OR MOISTURE.
As long as this unit is connected to the AC wall outlet,
it is not disconnected from the AC power source even
if you turn off this unit by MASTER ON/OFF. In this
state, this unit is designed to consume a very small
quantity of power.
FOR CANADIAN CUSTOMERS
To prevent electric shock, match wide blade of plug to
wide slot and fully insert.
This Class B digital apparatus complies with Canadian
ICES-003.
POUR LES CONSOMMATEURS CANADIENS
Pour éviter les chocs électriques, introduire la lame la
plus large de la fiche dans la borne correspondante de
la prise et pousser jusqu’au fond.
Cet appareil numérique de la classe B est conforme à
la norme NMB-003 du Canada.
IMPORTANT
Please record the serial number of this unit in the space
below.
MODEL:
Serial No.:
The serial number is located on the rear of the unit.
Retain this Owner’s Manual in a safe place for future
reference.
01EN_00_RX-V1700_U.book Page iii Tuesday, June 27, 2006 9:37 AM
1 En
PREPARATIONINTRODUCTION
BASIC
OPERATION
ADVANCED
OPERATION
ADDITIONAL
INFORMATION
FEATURES............................................................. 2
GETTING STARTED............................................ 3
Supplied accessories .................................................. 3
CONTROLS AND FUNCTIONS ......................... 4
Front panel ................................................................. 4
Remote control........................................................... 6
Zone 2/Zone 3 remote control ................................... 8
Preparing the remote control ..................................... 9
Front panel display .................................................. 10
Rear panel ................................................................ 12
CONNECTIONS .................................................. 13
Placing speakers....................................................... 13
Connecting speakers ................................................ 14
Using bi-amplification connections......................... 17
Information on jacks and cable plugs ...................... 18
Information on HDMI.............................................. 19
Audio and video signal flow.................................... 20
Connecting a TV monitor or projector .................... 21
Connecting other components ................................. 22
Connecting a multi-format player
or an external decoder ......................................... 26
Connecting a YAMAHA iPod universal dock ........ 27
Using the VIDEO AUX jacks on the front panel .... 27
Connecting the FM and AM antennas ..................... 28
Connecting the power cable..................................... 29
Setting the speaker impedance................................. 30
Turning on and off the power .................................. 31
AUTO SETUP....................................................... 32
Using AUTO SETUP .............................................. 32
PLAYBACK.......................................................... 38
Basic procedure ....................................................... 38
Selecting audio input jacks (AUDIO SELECT)...... 40
Selecting the MULTI CH INPUT component......... 41
Using your headphones............................................ 41
Muting the audio output........................................... 41
Displaying the input source information ................. 42
Playing video sources
in the background of an audio source.................. 43
Using the sleep timer ............................................... 43
SOUND FIELD PROGRAMS............................. 44
Selecting sound field programs ............................... 44
Sound field program descriptions ............................ 45
Enjoying unprocessed input sources........................ 49
USING AUDIO FEATURES............................... 50
Enjoying pure hi-fi sound ........................................ 50
Adjusting the tonal quality....................................... 50
Adjusting the speaker level...................................... 51
Enjoying multi-channel sources
in 2-channel stereo............................................... 51
Selecting the Compressed Music
Enhancer mode .................................................... 52
Selecting the night listening mode........................... 53
FM/AM TUNING..................................................54
FM/AM controls and functions ............................... 54
Automatic tuning ..................................................... 55
Manual tuning .......................................................... 56
Automatic preset tuning........................................... 57
Manual preset tuning ............................................... 58
Selecting preset stations........................................... 59
Exchanging preset stations ...................................... 60
XM SATELLITE RADIO TUNING ...................61
Connecting the XM Passport System ...................... 61
XM Satellite Radio controls and functions.............. 62
Activating XM Satellite Radio ................................ 63
Basic XM Satellite Radio operations....................... 65
Setting the XM Satellite Radio preset channels ...... 70
Displaying the XM Satellite Radio information...... 71
USING iPod ...........................................................73
Controlling iPod ...................................................... 73
RECORDING ........................................................75
ADVANCED SOUND CONFIGURATIONS.....76
Changing sound field parameter settings................. 76
Selecting decoders ................................................... 80
CUSTOMIZING THIS UNIT
(MANUAL SETUP) ..........................................84
Using SET MENU ................................................... 86
1 BASIC MENU...................................................... 87
2 SOUND MENU.................................................... 91
3 INPUT MENU...................................................... 94
4 OPTION MENU................................................... 97
REMOTE CONTROL FEATURES .................101
Controlling this unit, a TV,
or other components .......................................... 101
Setting remote control codes ................................. 103
Programming codes from other remote controls ... 105
Changing source names in the display window..... 106
Macro programming features ................................ 107
Clearing configurations ......................................... 110
USING MULTI-ZONE CONFIGURATION ...113
Connecting the Zone 2 and Zone 3 components ... 113
Controlling Zone 2 or Zone 3 ................................ 114
ADVANCED SETUP ..........................................117
Using ADVANCED SETUP ................................. 117
Setting remote control ID ...................................... 119
TROUBLESHOOTING .....................................122
RESETTING THE SYSTEM.............................130
GLOSSARY.........................................................131
SOUND FIELD PROGRAM
INFORMATION .............................................134
PARAMETRIC EQUALIZER
INFORMATION .............................................135
SPECIFICATIONS.............................................136
CONTENTS
INTRODUCTION
PREPARATION
BASIC OPERATION
ADVANCED OPERATION
ADDITIONAL INFORMATION
APPENDIX (at the end of this manual)
SOUND OUTPUT IN EACH SOUND FIELD
PROGRAM
LIST OF REMOTE CONTROL CODES
01EN_00_RX-V1700_U.book Page 1 Tuesday, June 27, 2006 9:37 AM
FEATURES
2 En
Built-in 7-channel power amplifier
Minimum RMS output power
(20 Hz to 20 kHz, 0.04% THD, 8 )
Front: 130 W + 130 W
Center: 130 W
Surround: 130 W + 130 W
Surround back: 130 W + 130 W
Sound field programs
Proprietary YAMAHA technology for the creation of sound
fields
Dolby Digital/Dolby Digital EX decoder
DTS/DTS-ES Matrix 6.1, Discrete 6.1, DTS Neo:6,
DTS 96/24 decoder
Dolby Pro Logic/Dolby Pro Logic II/Dolby Pro Logic IIx
decoder
Neural Surround decoder (U.S.A. and Canada models only)
Virtual CINEMA DSP
SILENT CINEMA
Sophisticated AM/FM tuner
40-station random and direct preset tuning
Automatic preset tuning
Preset station shifting capability (preset editing)
XM Satellite Radio
(U.S.A. and Canada models only)
XM Satellite Radio tuning capability (using the “XM Passport
System” sold separately)
Neural Surround decoder to play back the surround sound
content of XM Satellite Radio broadcasts in multi-channels,
resulting in a full surround sound experience
HDMI (High-Definition Multimedia Interface)
HDMI interface for standard, enhanced or
high-definition video (includes 1080p video signal
transmission) as well as multi-channel digital audio based on
HDMI version 1.2a
Analog video to HDMI digital video up-conversion
(composite video S-video component video HDMI
digital video) capability for monitor out
iPod controlling capability
DOCK terminal to connect a YAMAHA iPod universal dock
(such as the YDS-10, sold separately), which supports iPod
(Click and Wheel), iPod nano, and iPod mini
Other features
YPAO (YAMAHA Parametric Room Acoustic Optimizer) for
automatic speaker setup
192-kHz/24-bit D/A converter
OSD (on-screen display) menus that allow you to optimize
this unit to suit your individual audiovisual system
6 or 8-channel additional input jacks for discrete multi-
channel input
Analog video interlace/progressive conversion from 480i
(NTSC)/576i (PAL) to 480p/576p
S-video signal input/output capability
Component video input/output capability includes (3
COMPONENT VIDEO INs and 1 MONITOR OUT)
Optical and coaxial digital audio signal jacks
Pure Direct mode for pure hi-fi sound for all sources
Cinema and music night listening modes
Compressed Music Enhancer mode to improve the sound
quality of compression artifacts (such as the MP3 format) to
that of a high-quality stereo
Remote control with preset remote control codes, learning and
macro capability
ZONE 2/ZONE 3 custom installation facility
Zone switching capability between the main zone and
ZONE 2/ZONE 3 using ZONE CONTROLS
Sleep timer
Manufactured under license from Dolby Laboratories.
“Dolby”, “Pro Logic”, and the double-D symbol are trademarks
of Dolby Laboratories.
Manufactured under license from Digital Theater Systems, Inc.
“DTS”, “DTS-ES”, “NEO:6”, and “DTS 96/24” are trademarks
of Digital Theater Systems, Inc. Copyright 1996, 2003 Digital
Theater Systems, Inc. All right reserved.
“iPod” is a trademark of Apple Computer, Inc., registered in the
U.S. and other countries.
“HDMI”, the “HDMI” logo and “High-Definition Multimedia
Interface” are trademarks or registered trademarks of HDMI
Licensing LLC.
“SILENT CINEMA” is a trademark of YAMAHA
CORPORATION.
The XM name and related logos are registered trademarks of XM
Satellite Radio Inc.
Neural Surround
name and related logos are trademarks owned
by Neural Audio Corporation.
FEATURES
iPod
®
01EN_00_RX-V1700_U.book Page 2 Tuesday, June 27, 2006 9:37 AM
GETTING STARTED
3 En
INTRODUCTION
Check that you received all of the following parts.
GETTING STARTED
Supplied accessories
About this manual
y indicates a tip for your operation.
Some operations can be performed by using either the buttons on the front panel or the ones on the remote control. In case the
button names differ between the front panel and the remote control, the button name on the remote control is given in
parentheses.
This manual is printed prior to production. Design and specifications are subject to change in part as a result of improvements,
etc. In case of differences between the manual and product, the product has priority.
V
-
AUX/DOCK
+
+
+
ENTER
DISPLAY
AUDI O
MENU
TITLE
TV MUTE
TV INPUT
MUTE
4
3
2
ENT
+
10
0
9
5
1
AV
TV
7
6
8
RETURN
ON
OFF
CLEAR
LEARN
RENAME
MACRO
REC
DISC SKIP
VOLUME
CH
TV VOL
EFFECT
PARAMETER
STRAIGHT
XM MEMORY
A-E/CAT.
SRCH MODE
PURE DIRECT
PRESET/CH
SET MENU
BAN
D
LEVEL
ENHANCER
STEREO
SUR. DECODE
SELECT
EXTD SUR.
CLASSICAL
LIVE/CLUB
ENTERTAIN
MOVIE
NIGHT
TV
SOURCE
AMP
SELECT
DTV
DVR/VCR 2
VCR 1
DVD
CBL/SAT
MD/TAPE
CD-R
PHONO
TUNER CD
MULTI CH IN
SLEEP
AUDIO SEL
POWER
POWER
POWER
STANDBY
XM
Remote control
Batteries (6)
(AAA, R03, UM-4)
AM loop antenna
Optimizer microphoneSpeaker terminal wrench Power cable
Indoor FM antenna
(U.S.A., Canada, China, Asia, General,
and Korea models)
Indoor FM antenna
(Europe, U.K. and Australia models)
TUNER
CD
CD-R
DTV
PHONO
CBL/SAT
MD/TAPE
VCR 1
DVD
V-AUX/DOCK
DVR/VCR 2
POWER
XM
STANDBY
A-E/CAT.
PRESET/CH
A/B/C/D/E
PRESET
VOLUME
ZONE 3
ZONE 2
ID2
ID1
NUMBER
CAT.
ALL
PRESET
DISPLAY
MUTE
1
2
3
4
5
ENT
6
7
8
9
0
Zone 2/Zone 3
remote control
(except Europe model)
01EN_00_RX-V1700_U.book Page 3 Tuesday, June 27, 2006 9:37 AM
CONTROLS AND FUNCTIONS
4 En
This section describes only the amplifier controls and functions of this unit. See the following pages for details about
other control and functions.
AM/FM tuning ........................... see page 54
XM satellite radio tuning ........... see page 62
1 MASTER ON/OFF
Turns this unit on or off (see page 31).
2 MAIN ZONE ON/OFF
Turns on the main zone or sets it to the standby mode
(see page 31).
In the standby mode, this unit consumes a small amount of
power in order to receive infrared signals from the remote
control.
When you turn on this unit, there will be a 4 to 5-second delay
before this unit can reproduce sound.
This button is operational only when MASTER ON/OFF is
pressed inward to the ON position.
3 INPUT selector
Selects the desired input source (see page 38).
4 AUDIO SELECT
Toggles the priority for the type of audio input jack
between “AUTO”, “HDMI”, “COAX/OPT” and
“ANALOG” when one component is connected to two or
more input jacks (see page 40).
5 TONE CONTROL
Adjusts the bass/treble balance of the front left, front right
and center channels in conjunction with the PROGRAM
selector (see page 50).
6 STRAIGHT
Turns the sound field programs off or on. When the
“STRAIGHT” mode is selected, 2-channel or multi-
channel input signals are output directly from their
respective speakers without effect processing (see
page 49).
CONTROLS AND FUNCTIONS
Front panel
MASTER
PURE DIRECT
VOLU ME
MAIN ZONE
INPUT
ON
OFF
ENHANCER
NIGHT
ZONE ON/OFF
ZONE CONTROLS
DISPLAY
MODE
TUNING
PRESET/TUNING/CH
SEARCH MODE
EDIT
MULTI ZONE
FM/AM
T
UNING
PRESET/
MAN'L/AUTO FM
MEMORY
MIC
OPTIMIZER
EFFECT
STRAIGHT
CATEGORY
CONTROL
SELECT
AUDIO
TONE
A/B/C/D/E
PROGRAM
YPAO
ZONE 3
R
L
OPTICAL
ZONE 2
AUDIO
VIDEO AUX
SILENT CINEMA
S VIDEO
VIDEO
PHONES
ON/OFF
32 BA09
GFEDC
876541
(U.S.A. model)
Notes
01EN_00_RX-V1700_U.book Page 4 Tuesday, June 27, 2006 9:37 AM
CONTROLS AND FUNCTIONS
5 En
INTRODUCTION
7 MULTI ZONE buttons
ZONE 2 ON/OFF
Turns on Zone 2 only or sets it to the standby mode.
See page 114 for details.
ZONE 3 ON/OFF
Turns on Zone 3 only or sets it to the standby mode.
See page 114 for details.
These buttons are operational only when MASTER ON/OFF
is pressed inward to the ON position.
ZONE CONTROLS
Switches the zone you want to control between the
main zone, Zone 2 and Zone 3. See page 114 for
details.
y
After you press ZONE CONTROLS, the indicator for the
currently selected zone flashes in the front panel display for
approximately 5 seconds. While the indicator is flashing,
perform the desired operation.
8 Front panel display
Shows information about the operational status of this unit
(see page 10).
9 ENHANCER
Turns on or off the Compressed Music Enhancer mode
(see page 52).
0 Remote control sensor
Receives signals from the remote control (see page 9).
A NIGHT
Turns on or off the night listening modes (see page 53).
B PURE DIRECT
Turns on or off the Pure Direct mode (see page 50).
C PROGRAM selector
Selects sound field programs (see page 44).
Adjusts the bass/treble balance in conjunction with
TONE CONTROL (see page 50).
D OPTIMIZER MIC jack
Use to connect and input audio signals from the supplied
optimizer microphone in the “AUTO SETUP” procedure
(see page 32).
E PHONES jack
Outputs audio signals for private listening with
headphones (see page 41).
F VIDEO AUX jacks
Input audio and video signals from a portable external
source such as a game console or a video camera
(see page 27).
y
To reproduce the source signals input at these jacks, select
“V-AUX” as the input source.
The audio signals input at the DOCK terminal on the rear panel
take priority over the ones input at the VIDEO AUX jacks.
G VOLUME
Controls the output level of all audio channels.
y
This does not affect the AUDIO OUT (REC) level.
Opening and closing the front panel
door
When you want to use the controls behind the front panel
door, open the door by gently pressing on the lower part of
the panel. Keep the door closed when not using these
controls.
Note
Note
To open, press gently on the lower part of the panel.
01EN_00_RX-V1700_U.book Page 5 Tuesday, June 27, 2006 9:37 AM
CONTROLS AND FUNCTIONS
6 En
Remote control controls and functions
This section describes only the amplifier controls and functions of this unit. See the following pages for details about
other control and functions.
AM/FM tuning ........................................ see page 54
XM satellite radio tuning ........................ see page 62
Controlling a TV ................................... see page 101
Controlling other components ............... see page 102
Controlling option components ............. see page 103
The operation mode of the remote control buttons in the shaded
area below depends on the operation mode selector position. Set
the operation mode selector to AMP to control this unit.
1 Infrared window
Outputs infrared control signals. Aim this window at the
component you want to operate (see page 9).
2 TRANSMIT indicator
Flashes while the remote control is sending infrared
signals.
3 Input selector buttons
Select the input source you want to control.
y
The selected input source name appears in the display window on
the remote control showing which source is currently operational.
4 Display window
Shows the name of the selected input source that you can
control.
5 LEVEL
Selects the speaker channel to be adjusted and sets the
output level (see page 51).
6 Cursor buttons k / n / l / h, ENTER
Select and adjust the sound field program parameters or
the “SET MENU” parameters.
7 RETURN
Returns to the previous menu level when adjusting the
“SET MENU” parameters.
8 Sound field program selector buttons
Select sound field programs (see page 44).
9 SUR. DECODE
Activates decoders to play back 2-channel sources in
surround (see page 80).
Remote control
V
-
AUX/DOCK
+
+
+
ENTER
DISPLAY
AUDIO
MENU
TITLE
TV MUTE
TV INPUT
MUTE
4
3
2
ENT
+
10
0
9
5
1
AV
TV
7
6
8
RETURN
ON
OFF
CLEAR
LEARN
RENAME
MACRO
REC
DISC SKIP
VOLUME
CH
TV VOL
EFFECT
PARAMETER
STRAIGHT
XM MEMORY
A-E/CAT.
SRCH MODE
PURE DIRECT
PRESET/CH
SET MENU
B
AND
LEVEL
ENHANCER
STEREO
SUR. DECODE
SELECT
EXTD SUR.
CLASSICAL
LIVE/CLUB
ENTERTAIN
MOVIE
NIGHT
TV
SOURCE
AMP
SELECT
DTV
DVR/VCR 2
VCR 1
DVD
CBL/SAT
MD/TAPE
CD-R
PHONO
TUNER CD
MULTI CH IN
SLEEP
AUDIO SEL
POWER
POWER
POWER
STANDBY
XM
1
2
3
4
5
6
7
8
9
0
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
U
t
S
R
(U.S.A. model)
Note
01EN_00_RX-V1700_U.book Page 6 Tuesday, June 27, 2006 9:37 AM
CONTROLS AND FUNCTIONS
7 En
INTRODUCTION
0 MACRO ON/OFF
Turns on or off the macro function (see page 107).
A MACRO
Programs a series of operations to be controlled with a
single button (see page 107).
B STANDBY
Sets the main zone to the standby mode (see page 31).
This button is operational only when MASTER ON/OFF on the
front panel is pressed inward to the ON position.
C POWER
Turns on the main zone (see page 31).
This button is operational only when MASTER ON/OFF on the
front panel is pressed inward to the ON position.
D AUDIO SEL
Toggles the priority for the type of audio input jack
between “AUTO”, “HDMI”, “COAX/OPT” and
“ANALOG” when one component is connected to two or
more input jacks (see page 40).
E SLEEP
Sets the sleep timer (see page 43).
F MULTI CH IN
Selects the component connected to the MULTI CH
INPUT jacks as the input source when using an external
decoder, etc. (see page 41).
G SELECT k / n
Selects another input source that you can control
independently of the input source selected with the input
selector buttons.
H Operation mode selector
Selects the operation mode of the remote control buttons
in the shaded area.
AMP
Operates the amplifier function of this unit.
SOURCE
Operates the component selected with an input
selector button (see page 102).
TV
Operates the TV assigned to either DTV/CBL or
PHONO (see page 101).
To set the remote control codes for other components, see
page 103.
When you set the remote control codes for both DTV/CBL and
PHONO (see page 103), priority is given to the one set for
DTV/CBL.
I VOLUME +/
Increases or decreases the volume level.
J MUTE
Mutes the audio output. Press again to restore the audio
output to the previous volume level (see page 41).
K PURE DIRECT
Turns on or off the pure direct mode (see page 50).
L SET MENU
Enters “SET MENU” (see page 86).
M PAR AMET ER
Displays sound field parameter settings in the on-screen
display (OSD) (see page 76).
N STRAIGHT
Turns the sound field programs off or on. When the
“STRAIGHT” mode is selected, 2-channel or multi-
channel input signals are output directly from their
respective speakers without effect processing (see
page 49).
O EXTD SUR.
Switches between 5.1 and 6.1/7.1-channel playback of
multi-channel sources (see page 80).
P SELECT
Selects decoders for 2-channel sources (see pages 80 and
82).
Q ENHANCER
Turns on or off the Compressed Music Enhancer mode
(see page 52).
R NIGHT
Turns on or off the night listening modes (see page 53).
S RENAME
Changes the name of the input source in the display
window (see page 106).
T CLEAR
Clears remote control functions acquired from the learn,
macro and/or rename features (see page 110).
U LEARN
Programs remote control codes of functions from other
remote controls (see page 105).
Note
Note
Notes
01EN_00_RX-V1700_U.book Page 7 Tuesday, June 27, 2006 9:37 AM
CONTROLS AND FUNCTIONS
8 En
This section describes the function of each control on the
Zone 2/Zone 3 remote control used to control the amplifier
functions of Zone 2 or Zone 3.
See the following pages for details about other controls
and functions.
AM/FM tuning ........................................ see page 54
XM Satellite Radio tuning ...................... see page 62
Zone 2/Zone 3 remote control is supplied with U.S.A., Canada,
Australia, U.K., China, Asia and General models only.
1 Input selector buttons
Select the desired input source of Zone 2 or Zone 3.
2 ID1/ID2 switch
Switches the remote control ID between ID1 and ID2
(see page 104).
3 POWER
Turns on Zone 2 or Zone 3.
This button is operational only when MASTER ON/OFF on the
front panel is pressed inward to the ON position.
4 STANDBY
Sets Zone 2 or Zone 3 to the standby mode.
This button is operational only when MASTER ON/OFF on the
front panel is pressed inward to the ON position.
5 VOLUME +/
Increases or decreases the volume level of Zone 2 or
Zone 3.
6 MUTE
Mutes the sound of Zone 2 or Zone 3. Press again to
restore the audio output to the previous volume level.
7 ZONE 2/ZONE 3 switch
Switches between the operation mode of Zone 2 and that
of Zone 3.
Zone 2/Zone 3 remote control
Note
TUNER
CD
CD-R
DTV
PHONO
CBL/SAT
MD/TAPE
VCR 1
DVD
V-AUX/DOCK
DVR/VCR 2
POWER
XM
STANDBY
A-E/CAT.
PRESET/CH
A/B/C/D/E
PRESET
VOLUME
ZONE 3
ZONE 2
ID2
ID1
NUMBER
CAT.
ALL
PRESET
DISPLAY
MUTE
1
2
3
4
5
ENT
6
7
8
9
0
2
7
6
5
4
3
1
(U.S.A. model)
Note
Note
01EN_00_RX-V1700_U.book Page 8 Tuesday, June 27, 2006 9:37 AM
CONTROLS AND FUNCTIONS
9 En
INTRODUCTION
Installing batteries in the remote control
1 Press the part and slide the battery
compartment cover off.
2 Insert the four supplied batteries
(AAA, R03, UM-4) according to the polarity
markings (+ and –) on the inside of the
battery compartment.
3 Slide the cover back until it snaps into place.
Installing batteries in the Zone 2/Zone 3
remote control (Except Europe model)
1 Take off the battery compartment cover.
2 Insert the two supplied batteries (AAA, R03,
UM-4) according to the polarity markings
(+ and –) on the inside of the battery
compartment.
3 Snap the battery compartment cover back
into place.
Change all of the batteries if you notice the following
conditions:
the operation range of the remote control decreases.
the TRANSMIT indicator does not flash or its light becomes
dim.
Do not use old batteries together with new ones.
Do not use different types of batteries (such as alkaline and
manganese batteries) together. Read the packaging carefully as
these different types of batteries may have the same shape and
color.
If the batteries have leaked, dispose of them immediately. Avoid
touching the leaked material or letting it come into contact with
clothing, etc. Clean the battery compartment thoroughly before
installing new batteries.
Do not throw away batteries with general house waste; dispose
of them correctly in accordance with your local regulations.
If the remote control is without batteries for more than 2
minutes, or if exhausted batteries remain in the remote control,
the contents of the memory may be cleared. When the memory
is cleared, insert new batteries, set up the remote control code
and program any acquired functions that may have been
cleared.
Using the remote control
The remote control transmits a directional infrared ray.
Be sure to aim the remote control directly at the remote
control sensor on this unit during operation.
Do not spill water or other liquids on the remote control.
Do not drop the remote control.
Do not leave or store the remote control in the following types
of conditions:
places of high humidity, such as near a bath
places of high temperatures, such as near a heater or stove
places of extremely low temperatures
dusty places
Preparing the remote control
1
3
2
1
3
2
Notes
Notes
30 30
Approximately 6 m (20 ft)
Remote control sensor
01EN_00_RX-V1700_U.book Page 9 Tuesday, June 27, 2006 9:37 AM
CONTROLS AND FUNCTIONS
10 En
The XM indicator is only applicable to the U.S.A. and Canada models and the cursor on the left of the XM indicator lights up only when
“XM” is selected as the input source. For details, see “Basic XM Satellite Radio operations” on page 65.
1 HDMI indicator
Lights up when the signal of the selected input source is
input at HDMI IN 1 or HDMI IN 2 jacks (see page 19).
2 DOCK indicator
Lights up when you station your iPod in a YAMAHA iPod
universal dock (such as the YDS-10, sold separately)
connected to the DOCK terminal of this unit
(see page 27).
3 Battery charge indicator
Lights up when this unit charges the battery of the
stationed iPod in the standby mode of this unit. (see
page 73).
4 Input source indicators
The corresponding cursor lights up to show the currently
selected input source.
5 VOLUME level indicator
Indicates the current volume level.
6 MUTE indicator
Flashes while the MUTE function is on (see page 41).
7 Multi-information display
Shows the name of the current sound field program and
other information when adjusting or changing settings.
8 96/24 indicator
Lights up when a DTS 96/24 signal is input to this unit.
9 Input channel and speaker indicators
Input channel indicators
Indicate the channel components of the current digital
input signal.
Presence and surround back speaker
indicators
Light up according to the number of presence and
surround back speakers set for “PRESENCE SP” (see
page 89) and “SB L/R SP” (see page 89) in “SOUND
MENU” when “TEST” in “SOUND MENU” is set to
“ON” (see page 92).
y
You can make settings for the presence and surround back
speakers automatically by running “AUTO SETUP” (see
page 32) or manually by adjusting settings for “PRESENCE SP”
(see page 89) and “SB L/R SP” (see page 89) in “SOUND
MENU”.
Front panel display
Note
CD-R
CD
PHONO
MULTI CH
TUNER
XM
MD/TAPE
DVD
DTV
MUTE
VOLUME
dB
LFE
LL C R
SL SB SR
HiFi DSP
DIGITAL
EX
PL x
DSD
neural
PCM
VIRTUAL
YPAO
ENHANCER
MATRIX
DISCRETE
CINEMA
SILENT
24
96
96/24
TUNED
STEREO
AUTO
MEMORY
PS
ZONE2
ZONE3
SLEEP
PTY HOLD
PTY
RT
CT
EON
NIGHT
DOCK
VCR 1
CBL/SAT
DVR/VCR 2
V-AUX
DSD
neural
PCM
TUNED
STEREO
AUTO
MEMORY
PS
ZONE2
ZONE3
SLEEP
PTY HOLD
PTY
RT
CT
EON
NIGHT
HiFi DSP
DIGITAL
EX
PL x
VIRTUAL
YPAO
ENHANCER
MATRIX
DISCRETE
CINEMA
SILENT
24
96
K
J
I
H
G
F
D
C
B
A
0
P
O
N
M
L
9
87
654321
E
0........ U.S.A. and Canada models only
P........ U.K. and Europe models only
Presence speaker indicators
Input channel indicators
Surround back speaker indicators
L CR
SL SB SR
LFE
01EN_00_RX-V1700_U.book Page 10 Tuesday, June 27, 2006 9:37 AM
CONTROLS AND FUNCTIONS
11 En
INTRODUCTION
0 neural indicator
(U.S.A. and Canada models only)
Lights up when the Neural Surround decoder is activated
(see page 81).
A DSP indicators
The respective indicator lights up when any of the DSP
sound field programs are selected.
CINEMA DSP indicator
Lights up when you select a CINEMA DSP sound
field program (see page 45).
HiFi DSP indicator
Lights up when you select a HiFi DSP sound field
program (see page 45).
B VIRTUAL indicator
Lights up when Virtual CINEMA DSP is active (see
page 49).
C YPAO indicator
Lights up when you run “AUTO SETUP” and when the
speaker settings set in “AUTO SETUP” are used without
any modifications (see page 32).
D DSD indicator
Lights up when this unit is producing DSD (Direct Stream
Digital) digital audio signals.
E ENHANCER indicator
Lights up when the Compressed Music Enhancer mode is
turned on (see page 52).
F PCM indicator
Lights up when this unit is reproducing PCM (Pulse Code
Modulation) digital audio signals.
G Dolby decoder indicators
The respective indicator lights up when any of the Dolby
decoders of this unit function.
H Sound field indicators
Light up to indicate the active DSP sound fields.
I Headphones indicator
Lights up when headphones are connected (see page 41).
J SILENT CINEMA indicator
Lights up when headphones are connected and a sound
field program is selected (see page 49).
K DTS decoder indicators
The respective indicator lights up when any of the DTS
decoders of this unit function.
L Tuner indicators
Lights up when this unit is in the FM, AM or XM Satellite
Radio tuning mode.
TUNED indicator
Lights up when this unit is tuned into a station
(see page 54).
STEREO indicator
Lights up when this unit is receiving a strong signal
for an FM stereo broadcast while the AUTO indicator
is lit (see page 54).
AUTO indicator
Lights up when this unit is in the automatic tuning
mode (see page 54).
MEMORY indicator
Flashes to show that a station can be stored
(see page 57).
M ZONE2/ZONE3 indicators
Lights up when Zone 2 or Zone 3 is turned on
(see page 114).
N NIGHT indicator
Lights up when you select a night listening mode
(see page 53).
O SLEEP indicator
Lights up while the sleep timer is on (see page 43).
P Radio Data System indicators
(U.K. and Europe models only)
PS, PTY, RT and CT
Light up according to the selected Radio Data System
display mode.
EON
Lights up when the EON data service is being
received.
PTY HOLD
Lights up while searching for the Radio Data System
stations in the PTY SEEK mode.
Presence DSP sound field
Listening position
Surround left
DSP sound field
Surround right
DSP sound field
Surround back DSP sound field
01EN_00_RX-V1700_U.book Page 11 Tuesday, June 27, 2006 9:37 AM
CONTROLS AND FUNCTIONS
12 En
1 REMOTE jacks
See page 113 for details.
2 COMPONENT VIDEO jacks
See pages 21 and 22 for connection information.
3 Audio component jacks
See page 24 for connection information.
4 Video component jacks
See pages 21 and 22 for connection information.
5 ANTENNA terminals
See page 28 for connection information.
6 WRENCH HOLDER
Use to hook the supplied speaker terminal wrench when
not in use (see page 15).
7 VOLTAGE SELECTOR
(Asia and General models only)
See page 29 for details.
8 AC IN/OUTLET(S)
See page 29 for connection information.
9 HDMI connectors
See page 19 for connection information.
0 DOCK terminal
See page 27 for connection information.
A XM jack (U.S.A. and Canada models only)
See page 61 for connection information.
B DIGITAL INPUT/OUTPUT jacks
See page 22 for connection information.
C CONTROL OUT jack
This is a control expansion terminal for custom
installation.
D RS-232C terminal
This is a control expansion terminal for factory use only.
Consult your dealer for details.
E Speaker terminals
See page 14 for connection information.
F MULTI CH INPUT jacks
See page 26 for connection information.
G PRE OUT jacks
See page 25 for connection information.
H ZONE OUT jacks
See page 113 for connection information.
Rear panel
MULTI CH INPUT
PRE OUT
ZONE OUT
SUB
WOOFER
SUB
WOOFER
CENTER
CENTER
FRONT(6CH)
FRONT
SURROUND
SURROUND
PRESENCE
SUR.BACK/
SINGLE(SB)
ZONE 2
ZONE 3
SB(8CH)
8765432
HGF
EDCBA09
1
AC IN
AC OUTLETS
HOLDER
WRENCH
SPEAKERS
CENTER
BI-AMP
SURROUND BACK/
PRESENCE
SP1
FRONT
SURROUND
SINGLE
SP2
ANTENNA
FM
GND
AM
VIDEO
S VIDEO
MONITOR OUT
VIDEO
COMPONENT VIDEO
REMOTE
PHONO
GND
CD
IN(PLAY)
OUT(REC)
CD-R
HDMI
AUDIO
DOCK
XM
DIGITAL INPUT
MULTI CH INPUT
PRE OUT
CONTROL OUT
RS-232C
DIGITAL OUTPUT
ZONE OUT
SUB
WOOFER
SUB
WOOFER
CENTER
CENTER
FRONT(6CH)
FRONT
SURROUND
SURROUND
PRESENCE
SUR.BACK/
SINGLE(SB)
ZONE 2
ZONE 3
CD
D
VD
DVR/
VCR2
COAXIAL
1
2
CD
DVD
DTV
CBL/
SAT
MD/
TAP E
CD-R
OPTICAL
987
65
4
321
SB(8CH)
DTV
TAP E
MD/
(REC)
(PLAY)
IN
OUT
DVD
DVR/ VCR 2
VCR 1
CBL/SAT
OUT
OUT
ININ
DVD
DTV
CBL/SAT
MONITOR OUT
YY
P
R
P
R
P
B
P
B
IN
OUT
SAT
CBL/
IN 2
OUT
+
+
+
+
+
+
+
+
+
+
A B
C
R
L
R
R
L
L
R
R
L
R
L
L
DVD
IN 1
(U.S.A. model)
01EN_00_RX-V1700_U.book Page 12 Tuesday, June 27, 2006 9:37 AM
CONNECTIONS
13 En
PREPARATION
The speaker layout below shows the speaker setting we
recommend. You can use it to enjoy CINEMA DSP and
multi-channel audio sources.
Front left and right speakers (FL and FR)
The front speakers are used for the main source sound plus
effect sounds. Place these speakers at an equal distance from
the ideal listening position. The distance of each speaker
from each side of the video monitor should be the same.
Center speaker (C)
The center speaker is for the center channel sounds
(dialog, vocals, etc.). If for some reason it is not practical
to use a center speaker, you can do without it. Best results,
however, are obtained with the full system. Place the
center speaker centrally between the front speakers and as
close to the monitor as possible, such as directly over or
under it.
Surround left and right speakers (SL and SR)
The surround speakers are used for effect and surround
sounds. Place these speakers behind your listening
position, facing slightly inwards, about 1.8 m (6 ft) above
the floor.
Surround back left and right speakers
(SBL and SBR)
The surround back speakers supplement the surround
speakers and provide more realistic front-to-back
transitions. Place these speakers directly behind the
listening position and at the same height as the surround
speakers. They should be positioned at least 30 cm (12 in)
apart. Ideally, they should be positioned at the same width
as that of the front speakers.
Presence left and right speakers (PL and PR)
The presence speakers supplement the sound from the front
speakers with extra ambient effects produced by CINEMA
DSP (see page 134). These effects include sounds that
filmmakers intend to locate a little farther back behind the
screen in order to create more theater-like ambience. Place
these speakers at the front of the room about 0.5 to 1 m (1
to 3 ft) outside the front speakers, facing slightly inward,
and about 1.8 m (6 ft) above the floor.
Subwoofer (SW)
The use of a subwoofer with a built-in amplifier, such as
the YAMAHA Active Servo Processing Subwoofer
System, is effective not only for reinforcing bass
frequencies from any or all channels, but also for high
fidelity sound reproduction of the LFE (low-frequency
effect) channel included in Dolby Digital and DTS
sources. The position of the subwoofer is not so critical,
because low bass sounds are not highly directional. But it
is better to place the subwoofer near the front speakers.
Turn it slightly toward the center of the room to reduce
wall reflections.
CONNECTIONS
Placing speakers
SW
FR
PR
PL
FL
SBR
SBL
SL
SR
C
60˚
30˚
PL
PR
SBR
SBL
FL
FR
C
SL
SR
SR
80˚
SL
FR
PRPL
C
FL
1.8 m (6 ft)
30 cm (12 in) or more
1.8 m (6 ft)
0.5 to 1 m (1 to 3 ft) 0.5 to 1 m (1 to 3 ft)
01EN_00_RX-V1700_U.book Page 13 Tuesday, June 27, 2006 9:37 AM
14 En
CONNECTIONS
Be sure to connect the left channel (L), right channel (R), “+” (red) and “–” (black) properly. If the connections are faulty,
no sound will be heard from the speakers, and if the polarity of the speaker connections is incorrect, the sound will be
unnatural and lack bass.
Before connecting the speakers, make sure that this unit is turned off (see page 31).
Do not let the bare speaker wires touch each other or do not let them touch any metal part of this
unit. This could damage this unit and/or speakers.
Use magnetically shielded speakers. If this type of speaker still creates interference with the
monitor, place the speakers away from the monitor.
If you are to use 6 ohm speakers, be sure to set “SP IMP.” to “6MIN” before using this unit (see
page 30). 4 ohm speakers can be also used as the front speakers (see page 118).
A speaker cord is actually a pair of insulated cables running side by side. Cables are colored or shaped differently, perhaps with a
stripe, groove or ridge. Connect the striped (grooved, etc.) cable to the “+” (red) terminals of this unit and your speaker. Connect the
plain cable to the “–” (black) terminals.
The low-frequency signals of other speakers set to “SML” (or “SMALL”) or to “NONE” in “SPEAKER SET” (see pages 87 and 89)
are directed to the speakers selected in “LFE/BASS OUT” (see page 87).
You can connect both surround back and presence speakers to this unit, however they do not output sound simultaneously. You can set
to prioritize either set of speakers using the “PRIORITY” parameter in “MANUAL SETUP” (see page 89).
You can use the PRESENCE terminals to connect the Zone 2 or Zone 3 speakers as well as the presence speakers (see page 113).
Connecting speakers
Notes
CAUTION
SPEAKERS
CENTER
BI-AMP
SURROUND BACK/
PRESENCE
FRONT
SURROUND
SINGLE
SP2
PRE OUT
SUB
WOOFER
+
+
+
+
+
+
+
+
+
R
L
R
R
L
L
R
L
SP1
Front speakers
Surround speakers
(U.S.A. model)
Presence speakers
Subwoofer
Right
Left
Left
Center speaker
Surround back speakers
Right
Left
Left
Right
Right
Zone 2 or Zone 3
speakers
(see page 113)
01EN_00_RX-V1700_U.book Page 14 Tuesday, June 27, 2006 9:37 AM
15 En
CONNECTIONS
PREPARATION
FRONT terminals
Connect front left and right speakers to these terminals.
CENTER terminals
Connect a center speaker to these terminals.
SURROUND terminals
Connect surround left and right speakers to these
terminals.
SURROUND BACK terminals
Connect surround back left and right speakers to these
terminals.
When you use a surround back speaker, connect the speaker to the
left SURROUND BACK terminal (SINGLE).
PRESENCE terminals
Connect presence left and right speakers to these
terminals.
SUBWOOFER jack
Connect a subwoofer with a built-in amplifier (such as the
YAMAHA Active Servo Processing Subwoofer System)
to this jack.
Connecting the speaker cable
1 Remove approximately 10 mm (0.4 in) of
insulation from the end of each speaker
cable and then twist the exposed wires of the
cable together to prevent short circuits.
2 Loosen the knob using the supplied speaker
terminal wrench.
3 Insert one bare wire into the hole on the side
of each terminal.
4 Tighten the knob to secure the wire using the
supplied speaker terminal wrench.
Note
10 mm (0.4 in)
Speaker terminal wrench
Red: positive (+)
Black: negative (–)
01EN_00_RX-V1700_U.book Page 15 Tuesday, June 27, 2006 9:37 AM
16 En
CONNECTIONS
5 Hook the speaker terminal wrench onto the
WRENCH HOLDER on the rear panel of this
unit when not in use.
Connecting to the SP2 speaker
terminals
Connect Zone 2 or Zone 3 speakers to these terminals (see
page 113).
1 Open the tab.
2 Insert one bare wire into the hole on the
terminal.
3 Close the tab to secure the wire.
Connecting the banana plug
(except U.K., Europe, Asia and Korea
models)
The banana plug is a single-pole electrical connector
widely used to terminate speaker cables.
1 Tighten the knob using the supplied speaker
terminal wrench.
2 Insert the banana plug connector into the
end of the corresponding terminal.
y
You can also use the banana plug with the SP2 speaker terminals.
Open the tab and then insert one banana plug into the hole on the
terminal. Do not close the tab after connecting the banana plug.
Red: positive (+)
Black: negative (–)
Banana plug
Red: positive (+)
Black: negative (–)
Speaker terminal wrench
01EN_00_RX-V1700_U.book Page 16 Tuesday, June 27, 2006 9:37 AM
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144
  • Page 145 145
  • Page 146 146
  • Page 147 147
  • Page 148 148
  • Page 149 149
  • Page 150 150
  • Page 151 151
  • Page 152 152

Yamaha RX-V1700 Användarmanual

Kategori
AV-mottagare
Typ
Användarmanual