Nexa SP-812 Bruksanvisning

Typ
Bruksanvisning
SE812
Inomhussiren/
Indoor Siren
Svenska
SE812 är en Z-Wave inomhussiren med varselljus. Den kan anslutas till Nexa
Bridge eller annan kontroller som är Z-Wavecertierad.
Säkerhet
Läs igenom hela instruktionen först.
Anlita fackman vid behov. Nexa kan ej hållas ansvarig om den används till
annat än den är designad för eller om instruktionen inte följs. Anslut aldrig
lampor eller utrustning som överskrider mottagarens maximala belastning.
Det kan leda till fel, kortslutning eller brand. Försök inte att reparera
produkten. Den innehåller inga reparerbara delar. Produkten är inte vattentät.
Se till att den alltid är torr. Använd inte kemikalier, lösningsmedel eller starka
rengöringsmedel. Utsätt inte produkten för stark värme eller kyla.
Teknisk information
Inspänning 1.5 V LR14 x 4 or 6 VDC 600 mA
Frekvens Z-Wave (868,42 MHz)
Räckvidd Upp till 30 m
Dimensioner 155 x 90 x 50 mm
Arbetstemperatursområde -10°C - 40°C
Installation
Skruva ur skruven i botten och ta bort batteriluckan genom att dra den
nedåt.
Sätt i batterier eller anslut nätadapter (medföljer ej).
Skruva fast batteriluckan på önskad plats (ex på vägg).
Skjut på enheten på den fastkruvade luckan och skruva i skruven i botten.
Sirenen har inbyggt sabotagelarm. Om batteriluckan tas bort så kommer
sirenen att ljuda och blinka i 4 minuter. Denna funktion kan stängas av
genom att ta bort byglingen märkt [Tamper Jumper].
Sirenen har två ljudnivåer. Ljudnivån justeras med byglingen märkt [Sound
Jumper]
Inkludering i Z-Wave nätverk
På enheten nns en knapp [Link Key] som används för att inkludera,
exkludera, och återställa. Se vidare i manualen för Z-Wavekontrollern hur
enheten inkluderas eller exkluderas.
När inget nod-id nns lagrat blinkar LED:en varannan sekund och enheten
piper var tionde sekund.
Inkludera Tryck 3 gånger på [Link Key] inom 1,5 sekunder.
LED lyser grönt och enheten piper vid knapptryck-
ning.
Exkludera Tryck 3 gånger på [Link Key] inom 1,5 sekunder.
LED lyser grönt och enheten piper vid knapptryck-
ning.
Återställning Tryck 3 gånger på [Link Key] inom 1,5 sekunder.
Tryck, inom 1 sekund, och håll [Link Key] nedtryckt
tills dess att enheten piper i 5 sekunder.
Enheten är nu återställd.
Associera Sätt Z-Wavekontrollern i associeringsläge.
Tryck 3 gånger på [Link Key] inom 1,5 sekunder.
Enheten kommer att skicka NIF som markerar att
den är associeringsläge.
För information angånde programmering av Z-Wavemodulen, se baksidan.
Användning
Se manualen till din Z-Wavekontroller för information hur du använder SE812
efter att den är inkluderad..
mer information på:
www.nexa.se/zwave
English
SE812 is a Z-Wave indoor siren with strobe light. It can be connected to
Nexa Bridge or other Z-Wave controller.
Safety
Read the instructions rst.
Call in professional as needed. Nexa can not be held responsible if it is used
for other purposes than it is designed for, or if instructions are not followed.
Never connect lights or equipment that exceeds the recipient’s maximum
load. It can lead to failure, short circuit or re. Do not attempt to repair the
product. It contains no serviceable parts. The product is not waterproof.
Make sure it is completely dry. Do not use chemicals, solvents or harsh
detergents. Do not expose to extreme heat or cold.
Technical information
Power supply 1.5 V LR14 x 4 or 6 VDC 600 mA
Frequency Z-Wave (868,42 MHz)
Range Up to 30 m
Dimensions 155 x 90 x 50 mm
Environment temp. range -10°C - 40°C
Installation
Remove the screw at the bottom and slide battery cover down.
Insert batteries or use power adapter (not included).
Mount rear cover at wall.
Slide the unit down on the rear cover and tighten the screw.
The siren has a tamper alarm. When the battery cover is removed the alarm
will sound and the strobe will ash for 4 minutes. This function can be turned
o by removing the jumper marked [Tamper Jumper].
The siren has two sound levels. This is adjusted with jumper marked [Sound
Jumper]
Adding to a Z-Wave network
The button marked [Link Key] on the unit is used to include, exclude and
reset the unit.
See Z-Wave controller manual how inclusion/exclusion is done.
The Led ashes at every other second and the unit beeps every 10th
second when no Node ID is stored.
Include Press [Link Key] 3 times within 1,5 seconds.
Exclude Press [Link Key] 3 times within 1,5 seconds.
Reset Press [Link Key] 3 times within 1,5 seconds. Then,
within 1 seconds, press and hold [Link Key] until
LED turns o.
The unit is now reset and enters auto inclusion
mode.
Association Set Z-Wave controller in association mode.
Press [Link Key] 3 times within 1,5 seconds. The
unit will now transmit NIF that indicats that it is in
association mode.
For more information regarding how to program the Z-wave unit, see the
other side.
Operation
See Z-Wave controller’s manual for information how to use SE812 when it
is included.
more information at:
www.nexa.se/zwave
LED
Red
Strobe Light
DC Jack
Jumpers
Link
Key
Tamper
Switch
se812_86804_manual_001 | 1
The following information is for someone that has some experience setting up a Z-Wave
system or someone that has computer software running a Z-Wave controller.
1. Z-Wave’s Groups (Association Command Class Version 2)
The Indoor Siren can be set to send reports to associated Z-Wave devices. It supports
one association group with 5 nodes support for Grouping 1. For Grouping 1, the Siren
will emit reports including POWER_APPLIED, Tamper Trigger Report and Battery & Low
Battery Report.
1-1 POWER_APPLIED command
When power is applied, it will send ALARM_REPORT command to nodes of Grouping 1 to
inform the devices that the Siren is powered up.
ALARM_REPORT Command
[Command Class Alarm, Alarm Report, Type = 0x02, Level = 0x01]
1-2 Tamper Trigger Report
When tamper switch is triggered, Siren will send ALARM_REPORT command to nodes of
Grouping 1 to inform the devices that the Siren has been triggered.
ALARM_REPORT Command
[Command Class Alarm, Alarm Report, Type = 0x01, Level = 0x11]
1-3 Battery & Low Battery Report
When the battery level of the Siren drops to an unacceptable level, the Siren will ash red
LED once every 30 seconds and send Broadcast command to the network.
ALARM_REPORT Command
[Command Class Alarm, Alarm Type = 0x01, Alarm Level = 255(0xFF)]
The users can also enquire the battery status of the Siren by sending BATTERY_ GET
command via controller. Once the Siren receives the command, it will return BATTE-
RY_REPORT command. If the unit is in low battery status, a Battery_Level = 255 (0xFF)
command will be sent to the Z-Wave Controller.
BATTERY_REPORT Command
[Command Class Battery, Battery Report, Battery Level = 20%-100%]
2. Basic Command Class / Binary Switch Command Class
The Siren will respond to BASIC and BINARY commands that are part of the Z-Wave
system.
2-1 BASIC_SET/SWITCH_BINARY_SET
Upon receipt of the following commands from a Z-Wave Controller, the Siren will either
generate a full alarm condition (on) or stop the full alarm condition (o).
[Command Class Basic, Basic Set, Value = 255(0xFF)]: the Siren generates a full alarm
condition by ashing strobe light and sounding alarm for 3 minutes.
[Command Class Basic, Basic Set, Value = 0(0x00)]: the Siren stops full alarm condition.
[Command Class Switch Binary, Switch Binary Set, Value = 255(0xFF)]: the Siren generates
a full alarm condition by ashing strobe light and sounding alarm for 3 minutes.
[Command Class Switch Binary, Switch Binary Set, Value = 0(0x00)]: the Siren stops full
alarm condition.
2-2 BASIC_GET/BINARY_SWITCH_GET
Upon receipt of the following commands from a Z-Wave Controller, the Siren will report its
On/O status to the Controller.
Basic Get Command: [Command Class Basic, Basic Get]
Basic Report Command:
Report OFF: [Command Class Basic, Basic Report, Value = 0(0x00)]
Report ON:[Command Class Basic, Basic Report, Value = 255(0xFF)]
Binary Switch Get Command:[Command Class Switch Binary, Switch Binary Get]
Binary Switch Report Command
Report OFF:
[Command Class Switch Binary, Switch Binary Report, Value =0(0x00)]
Report ON:
[Command Class Switch Binary, Switch Binary Report, Value = 255(0xFF)]
Note: To execute the command of BASIC_SET/SWITCH¬_BINARY_SET, BASIC_GET/
BINARY_SWITCH_GET and BATTERY_GET, the notes in the network must support the
function of Z-Wave Wake Up Beam in order to wake the Siren up from sleep status.
3. Command Classes
The Siren supports Command Classes including…
COMMAND_CLASS_BASIC
COMMAND_CLASS_SWITCH_BINARY
COMMAND_CLASS_VERSION
COMMAND_CLASS_ASSOCIATION_V2
COMMAND_CLASS_BATTERY
COMMAND_CLASS_MANUFACTURER_SPECIFIC
Programming
Is herewith conrmed to comply with the requirements set out in the Council
Directive on the Approximation of the Laws of the Member States relating to
Radio Equipment and Telecommunications Terminal Equipment (RED) Directive
2014/54/EU, Low-voltage Directive (2014/35/EU). For the evaluation regarding
the Directives, the following standards were applied:
EN301489-1
EN301489-3
EN300220-1
EN300220-2
EN60950-1
Company Name: Nexa Trading AB
Adress: Karl Johansgatan 152, 40242, Göteborg, Sweden
Signatur: _________________________________________
Name: Erik Hjelmström
Title: Vice President
Date, Place: 17 May 2016, Göteborg
DECLARATION OF CONFORMITY
se812_86804_manual_001 | 2
  • Page 1 1
  • Page 2 2

Nexa SP-812 Bruksanvisning

Typ
Bruksanvisning

på andra språk