Yamaha NX-C430 Bruksanvisning

varumärke: Yamaha

Modell: NX-C430

Kategori: Bärbara högtalare

Typ: Bruksanvisning

Denna manual är också lämplig för

NS-P430/

NS-P436

(NS-P430/NS-P436: NX-430P + NX-C430 + YST-SW015)

HOME CINEMA 5.1CH SPEAKER PACKAGE/

HOME CINEMA 6.1CH SPEAKER PACKAGE

OWNER’S MANUAL

U B

NS-P430-436(UB)-PREc 03.2.28, 7:02 PM1

• Explanation of Graphical Symbols

The lightning flash with arrowhead

symbol, within an equilateral triangle,

is intended to alert you to the

presence of uninsulated “dangerous

voltage” within the product’s

enclosure that may be of sufficient

magnitude to constitute a risk of

electric shock to persons.

The exclamation point within an

equilateral triangle is intended to alert

you to the presence of important

operating and maintenance

(servicing) instructions in the

literature accompanying the

appliance.

IMPORTANT SAFETY INSTRUCTIONS

1 Read these instructions.

2 Keep these instructions.

3 Heed all warnings.

4 Follow all instructions.

5 Do not use this apparatus near water.

6 Clean only with dry cloth.

7 Do not block any ventilation openings. Install in

accordance with the manufacturer’s instructions.

8 Do not install near any heat sources such as radiators,

heat registers, stoves, or other apparatus (including

amplifiers) that produce heat.

9 Do not defeat the safety purpose of the polarized or

grounding-type plug. A polarized plug has two blades

with one wider than the other. A grounding type plug

has two blades and a third grounding prong. The wide

blade or the third prong are provided for your safety. If

the provided plug does not fit into your outlet, consult

an electrician for replacement of the obsolete outlet.

10 Protect the power cord from being walked on or

pinched particularly at plugs, convenience receptacles,

and the point where they exit from the apparatus.

11 Only use attachments/accessories specified by the

manufacturer.

12 Use only with the cart, stand, tripod,

bracket, or table specified by the

manufacturer, or sold with the

apparatus. When a cart is used, use

caution when moving the cart/

apparatus combination to avoid injury

from tip-over.

13 Unplug this apparatus during lightning storms or when

unused for long periods of time.

14 Refer all servicing to qualified service personnel.

Servicing is required when the apparatus has been

damaged in any way, such as power-supply cord or

plug is damaged, liquid has been spilled or objects

have fallen into the apparatus, the apparatus has been

exposed to rain or moisture, does not operate normally,

or has been dropped.

● Be sure to allow spaces of at least 20 cm above,

behind and on both sides of the unit.

● Do not place the following objects on this unit:

A vessel with water in it.

If the vessel falls by vibrations and water spills, it

may cause damage to the unit, and/or you may get

an electric shock.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC

SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN

OR MOISTURE.

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE

COVER (OR BACK). NO USER-SERVICEABLE

PARTS INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION

IMPORTANT

Please record the serial number of this system in

the space below.

Model:

Serial No.:

The serial number is located on the rear of the

main unit.

Retain this Owner’s Manual in a safe place for

future reference.

NS-P430-436(UB)-PREc 03.2.28, 7:02 PM2

III

We Want You Listening For A Lifetime

YAMAHA and the Electronic Industries Association’s

Consumer Electronics Group want you to get the most out

of your equipment by playing it at a safe level. One that lets

the sound come through loud and clear without annoying

blaring or distortion – and, most importantly, without

affecting your sensitive hearing.

Since hearing damage from loud sounds is

often undetectable until it is too late, YAMAHA

and the Electronic Industries Association’s

Consumer Electronics Group recommend you

to avoid prolonged exposure from excessive

volume levels.

FCC INFORMATION (for US customers only)

1. IMPORTANT NOTICE : DO NOT MODIFY THIS

UNIT!

This product, when installed as indicated in the

instructions contained in this manual, meets FCC

requirements. Modifications not expressly approved

by Yamaha may void your authority, granted by the

FCC, to use the product.

2. IMPORTANT : When connecting this product to

accessories and/or another product use only high

quality shielded cables. Cable/s supplied with this

product MUST be used. Follow all installation

instructions. Failure to follow instructions could void

your FCC authorization to use this product in the

USA.

3. NOTE : This product has been tested and found to

comply with the requirements listed in FCC

Regulations, Part 15 for Class “B” digital devices.

Compliance with these requirements provides a

reasonable level of assurance that your use of this

product in a residential environment will not result in

harmful interference with other electronic devices.

This equipment generates/uses radio frequencies

and, if not installed and used according to the

instructions found in the users manual, may cause

interference harmful to the operation of other

electronic devices.

Compliance with FCC regulations does not guarantee that

interference will not occur in all installations. If this

product is found to be the source of interference, which

can be determined by turning the unit “OFF” and “ON”,

please try to eliminate the problem by using one of the

following measures:

Relocate either this product or the device that is being

affected by the interference.

Utilize power outlets that are on different branch (circuit

breaker or fuse) circuits or install AC line filter/s.

In the case of radio or TV interference, relocate/reorient

the antenna. If the antenna lead-in is 300 ohm ribbon

lead, change the lead-in to coaxial type cable.

If these corrective measures do not produce satisfactory

results, please contact the local retailer authorized to

distribute this type of product. If you can not locate the

appropriate retailer, please contact Yamaha Electronics

Corp., U.S.A. 6660 Orangethorpe Ave, Buena Park, CA

90620.

The above statements apply ONLY to those products

distributed by Yamaha Corporation of America or its

subsidiaries.

NS-P430-436(UB)-PREc 03.2.28, 7:02 PM3

Speaker cables

Subwoofer cable

Fasteners (for NX-C430)

Nonskid pads (for YST-SW015)

Main and rear speakers

(and rear center speaker for NS-P436)

Center speaker

Subwoofer

UNPACKING Please check to make sure all listed items are included.

[4m]

[15m]

X 2

X 3

NX-430P

NX-C430

YST-SW015

X 2

<NS-P430>

X 3

NS-P436>

X 4

<NS-P430>

X 5

<NS-P436>

SUBWOOFER SYSTEM YST-SW015

STANDBY/ON B.A.S.S. HIGH CUT

–

150Hz

VOLUME

–

SPECIAL INSTRUCTIONS FOR U.K. MODEL

IMPORTANT:

THE WIRES IN MAINS LEAD ARE COLOURED IN

ACCORDANCE WITH THE FOLLOWING CODE:

Blue: NEUTRAL

Brown: LIVE

As the colours of the wires in the mains lead of this

apparatus may not correspond with the coloured markings

identifying the terminals in your plug, proceed as follows:

The wire which is coloured BLUE must be connected to

the terminal which is marked with the letter N or coloured

BLACK. The wire which is coloured BROWN must be

connected to the terminal which is marked with the letter L

or coloured RED. Making sure that neither core is

connected to the earth terminal of the three pin plug.

For U.K. customers

If the socket outlets in the home are not suitable for the plug

supplied with this appliance, it should be cut off and an

appropriate 3 pin plug fitted. For details, refer to the

instructions described below.

Note: The plug severed from the mains lead must be

destroyed, as a plug with bared flexible cord is hazardous if

engaged in a live socket outlet.

For Canadian Customers

To prevent electric shock, match wide blade of plug to

wide slot and fully insert.

This Class B digital apparatus complies with Canadian

ICES-003.

NS-P430-436(UB)-PREc 03.2.28, 7:02 PM4

English

E-1

● To assure the finest performance, please read this manual

carefully. Keep it in a safe place for future reference.

● Install the speakers in a cool, dry, clean place – away from

windows, heat sources, sources of excessive vibration, dust,

moisture and cold. Avoid sources of humming (transformers,

motors). To prevent fire or electric shock, do not expose the

speakers to rain or water.

● To prevent the enclosure from warping or discoloring, do not

place the speakers where they will be exposed to direct sunlight

or excessive humidity.

● Avoid installing the speakers where foreign objects may fall onto

them and/or where they may be exposed to liquid dripping or

splashing.

Do not place the following objects on top of the speakers:

●

Other components, as they might cause damage and/or

discoloration on the surface of the speakers.

●

Burning objects (i.e. candles), as they might cause fire,

damage to the speakers and/or personal injury.

●

Containers with liquid in them, as they might cause electric

shock to the user and/or damage to the speakers.

● Do not place the speakers where they are liable to be knocked

over or struck by falling objects. Stable placement will also

ensure better sound performance.

● Placing the speakers on the same shelf or rack as the turntable

can result in feedback.

● Secure placement or installation is the owner’s responsibility.

YAMAHA shall not be liable for any accident caused by improper

placement or installation of speakers.

● Any time you note distortion, reduce the volume control on your

amplifier to a lower setting. Never allow your amplifier to be

driven into “clipping”. Otherwise the speakers may be damaged.

● When using an amplifier with a rated output power higher than

the nominal input power of the speakers, care should be taken

never to exceed the speakers’ maximum input.

● Do not attempt to clean the speakers with chemical solvents as

this might damage the finish. Use a clean, dry cloth.

● Do not attempt to modify or fix the speakers. Contact qualified

YAMAHA service personnel when any service is needed. The

cabinet should never be opened for any reason.

● Be sure to read the “TROUBLESHOOTING” section regarding

common operating errors before concluding that the speakers

are faulty.

For YST-SW015

● Do not operate this unit upside down. It may overheat, possibly

causing damage.

● Do not use excessive force on switches, controls or connection

wires. When moving this unit, first disconnect the power plug

and the wires connected to other equipments. Never pull the

wires themselves.

● Since this unit has a built-in power amplifier, heat will radiate

from the rear panel. Place the unit apart from the walls, allowing

spaces of at least 20 cm above, behind and on both sides of the

unit to prevent fire or damage. Furthermore, do not position with

the rear panel facing down on the floor or other surfaces.

● When using a humidifier, be sure to avoid condensation inside

this unit by allowing enough spaces around this unit or avoiding

excess humidification. Condensation might cause a fire, damage

to this unit, and/or electric shock.

CAUTION: Read this before operating your unit.

Thank you for selecting this YAMAHA NS-P430/NS-P436 Speaker Package.

● Do not cover the rear panel of this unit with a newspaper, a

tablecloth, a curtain, etc. in order not to obstruct heat radiation. If

the temperature inside this unit rises, it may cause fire, damage

to this unit and/or personal injury.

● Do not plug in this unit to a wall outlet until all connections are

completed.

● The voltage to be used must be the same as that specified on

the rear panel. Using this unit with a higher voltage than

specified is dangerous and may cause fire, damage to this unit,

and/or personal injury. YAMAHA will not be held responsible for

any damage resulting from use of this unit with a voltage other

than specified.

● To prevent lightning damage, disconnect the AC power plug

when there is an electric storm.

● Super-bass frequencies reproduced by this unit may cause a

turntable to generate a howling sound. In such a case, move this

unit away from the turntable.

● This unit may be damaged if certain sounds are continuously

outputted at high volume level. For example, if 20 Hz–50 Hz sine

waves from a test disc, bass sounds from electronic instruments,

etc. are continuously outputted, or when the stylus of a turntable

touches the surface of a disc, reduce the volume level to prevent

this unit from being damaged.

● If you hear distorted noise (i.e. unnatural, intermittent “rapping” or

“hammering” sounds) coming from this unit, reduce the volume

level. Extremely loud playing of a movie soundtrack’s low

frequency, bass-heavy sounds or similarly loud popular music

passages can damage this speaker system.

● Vibration generated by super-bass frequencies may distort

images on a TV. In such a case, move this unit away from the TV

set.

● When disconnecting the power cord from the wall outlet, grasp

the plug; do not pull the cord.

● When not planning to use this unit for a long period (i.e. vacation,

etc.), disconnect the AC power plug from the wall outlet.

● VOLTAGE SELECTOR

(For China, Korean and General models)

The voltage selector switch on the rear

panel of this unit must be set for your

local main voltage BEFORE plugging

this unit into the AC main supply.

Voltages are 110-120/220-240 V AC, 50/

60 Hz.

Standby mode

If the POWER switch is set to the ON position and the AUTO

STANDBY switch is set to the HIGH or LOW position, this unit

turns into the standby mode when no signal is received by this

unit for 7 to 8 minutes.

In this state, this unit is designed to consume a very small

quantity of power.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO

NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.

110V

–

120V 220V

–

240V

VOLTAGE

SELECTOR

NS-P430-436 (UB) 03.2.28, 7:02 PM1

E-2

CONTENTS

IMPORTANT SAFETY INSTRUCTIONS ........ II

UNPACKING .................................................. IV

CAUTION ......................................................... 1

COMPONENTS OF THE PACKAGE .............. 2

SETTING UP THE SPEAKERS ...................... 3

Placing the subwoofer ................................... 4

Placing the center speaker ............................. 4

Mounting the main/rear/center speakers

(and rear center speaker for NS-P436)

on a wall ............................................................

Mounting the main/rear speakers

(and rear center speaker for NS-P436)

by using commercially available speaker

stands or brackets .............................................

CONNECTIONS.............................................. 7

An example of basic connections .................... 7

How to connect speaker cables to the input

and output terminals of the speakers ............... 9

USING THE SUBWOOFER (YST-SW015) ... 10

Controls and their functions .......................... 10

Automatic power-switching functon ................. 11

Adjusting the subwoofer before use ................ 12

Frequency characteristics ................................ 13

ADVANCED YAMAHA ACTIVE SERVO

TECHNOLOGY (for YST-SW015) ................ 14

TROUBLESHOOTING .................................. 15

SPECIFICATIONS .......................... Back Cover

COMPONENTS OF THE PACKAGE

<NX-430P>

2-way acoustic-suspension speaker system used for

the main and rear speakers (and rear center speaker for

NS-P436)

<NX-C430>

2-way acoustic-suspension speaker system used for

the center speaker

<YST-SW015>

Active Servo Processing Subwoofer System with a

built-in power amplifier

● This subwoofer system employs Advanced Yamaha

Active Servo Technology which YAMAHA has developed

for reproducing higher quality super-bass sound. (Refer to

page 14 for details on Advanced Yamaha Active Servo

Technology.) This super-bass sound adds a more

realistic, theater-in-the-home effect to your stereo system.

● The HIGH CUT control enables you to adjust the tone

balance between the subwoofer and the main speakers.

● The Automatic power-switching function saves you the

trouble of pressing the STANDBY/ON button to turn the

power on or turn it to the STANDBY mode.

The speaker package “NS-P430 and NS-P436” is designed

for use in a multi-channel audio system such as a home

theater system.

NS-P430 includes four NX-430P speaker systems, one NX-

C430 speaker system and one YST-SW015 subwoofer

system.

NS-P436 includes five NX-430P speaker systems, one NX-

C430 speaker system and one YST-SW015 subwoofer

system.

QD-Bass Technology

QD-Bass (Quatre Dispersion Bass) technology uses

square, pyramid-shaped reflective plates to radiate the

sound in four horizontal directions.

■ About this manual

• This manual is printed prior to production. Design

and specifications are subject to change in part for the

reason of the improvement in operativity ability, and

others. In this case, the product has priority.

• Some of the illustrations and names of the package

contents etc. written in this manual may differ from

the actual products and the names written on the

package etc.

NS-P430-436 (UB) 03.2.28, 7:02 PM2

English

E-3

SETTING UP THE SPEAKERS

Before making connections, place all speakers in their respective positions. The positioning of the speakers is important

because it controls the whole sound quality of this system.

Place the speakers depending on your listening position by following the instructions below.

Speaker configuration

<NS-P430>

This speaker package employs a 6 speaker configuration: 2

main speakers, 2 rear speakers, a center speaker and a

subwoofer.

The main speakers emit main source sound. The rear

speakers emit surround sounds, and the center speaker

emits center sounds (dialog etc.). The subwoofer emits

reinforcing low frequencies on your audio system.

<NS-P436>

This speaker package employs a 7 speaker configuration: 2

main speakers, 2 rear speakers, a center speaker, a rear

center speaker and a subwoofer.

The main speakers emit main source sound. The rear and

rear center speakers emit surround sounds, and the center

speaker emits center sounds (dialog etc.). The subwoofer

emits reinforcing low frequencies on your audio system.

Note

In this speaker package, the same speakers (NX-430P)

are used for the main and rear speakers (and rear

center speaker for NS-P436).

Placing speakers

Main speakers: On both sides of and at approximately

the same height as the TV set.

Rear speakers: Behind your listening position, facing

slightly inward. About 1.8 m (approx. 6

feet) from the floor.

Center speaker: Precisely between the main speakers.

Rear center speaker (for NS-P436):

Precisely between the rear speakers.

Subwoofer: The position of the subwoofer is not so

critical because low bass tones are not

highly directional.

Refer to “Placing the subwoofer” on

page 4 for a recommended positioning

of the subwoofer.

Main L Center Main R

Rear L

Subwoofer

Rear R

Main L

Main R

Subwoofer

Center

Rear L

Rear R

TV-set

Rear center

(for NS-P436)

Rear center

(for NS-P436)

These speakers feature a magnetically shielded design,

but there is still a chance that placing them too close to a

TV set might impair picture color. Should this happen,

move the speakers away from the TV set.

NS-P430-436 (UB) 03.2.28, 7:02 PM3

E-4

䡵 Placing the subwoofer

It is recommended to place the subwoofer on the outside of

either the right or the left main speaker. (See fig. Å .) The

placement shown in fig. ı is also possible, however, if the

subwoofer system is placed directly facing the wall, the

bass effect may die because the sound from it and the

sound reflected by the wall may cancel out each other. To

prevent this from happening, face the subwoofer system at

an angle as shown in fig. Å.

Note

There may be a case that you cannot obtain enough super-

bass sounds from the subwoofer when listening in the

center of the room. This is because “standing waves” have

been developed between two parallel walls and they cancel

the bass sounds.

In such a case, face the subwoofer obliquely to the wall. It

also may be necessary to break up the parallel surfaces by

placing bookshelves etc. along the walls.

Use the nonskid pads

Put the provided nonskid pads at the four corners on the

bottom of the subwoofer to prevent the subwoofer from

moving by vibrations etc.

( : Subwoofer, : Main speaker)

ıÅ

You can place the speaker on top of the TV if the top is flat,

on the floor under the TV, or inside the TV rack . Be sure to

place the speaker in a stable position.

When placing the speaker on top of the TV, to prevent the

speaker from falling, attach the provided fasteners at two

points on the bottom of the speaker and on the top of the

TV.

䡵 Placing the center speaker

Notes

● Do not place the speaker on top of a TV whose area is

smaller than the bottom of the speaker. If placed, the

speaker may fall and cause injury.

● Do not place the speaker on top of a TV if the top is

inclined.

● Do not touch the adhesive surface after peeling off

the seal as this will weaken its adhesive strength.

● Thoroughly wipe clean the surface where the fastener

is to be applied. Note that adhesive strength is

weakened if the surface is dirty, oily or wet and that

this may cause the center speaker to fall.

Peel off

the seal

Fastener

NS-P430-436 (UB) 03.2.28, 7:02 PM4

English

E-5

䡵 Mounting the main/rear/center speakers (and rear center

speaker for NS-P436) on the wall

You can mount the main, rear and/or center speakers (and/

or rear center speaker for NS-P436) on a wall.

To mount the speakers on a wall, use the holes of the

brackets attached on the speakers’ back panels.

1 Fasten two screws into a firm wall or wall support at the

interval shown below.

Main/rear/rear center (for NS-P436) .......... 26 mm (1”)

Center ............................................. 222.8 mm (8-3/4”)

2 Hang the speaker by mounting the holes on the

protruding screws.

* Make sure that the screws are securely affixed by the

narrow parts of the holes.

WARNING

● Each speaker weighs as follows.

Main/rear/rear center (for NS-P436)

...................................................... 1.2 kg (2 lbs. 10 oz.)

Center .......................................... 1.7 kg (3 lbs. 12 oz.)

Do not mount them on thin plywood or a wall

composed of a soft surface material. If mounted, the

screws may pull out of the flimsy surface and the

speakers may fall. This may damage the speakers or

cause personal injury.

● Do not affix the speakers to a wall using nails,

adhesives, or any other unstable hardware. Long-

term use and vibrations may cause the speakers to

fall.

● To avoid accidents resulting from tripping over loose

speaker cables, fix the cables to the wall.

● Select an appropriate position on the wall to mount

the speaker so that no one will injure his/her head or

face.

26 mm

Holes

Wall/ wall support

Tapping screw

(Available at the

hardware store)

Min.

20 mm

Diam. 3.5 to 4 mm

4 mm

Main/rear/rear center (for NS-P436)

Center

222.8 mm

Main/rear/rear center (for NS-P436)

Center

NS-P430-436 (UB) 03.2.28, 7:02 PM5

E-6

The front cover is fastened to the enclosure at four points

and can be removed if desired. To remove the cover, hold

on to both sides and slowly pull straight away from the

speaker. To reattach, line up the four holes on the inner

surface of the cover with the four corresponding pegs on the

speaker and push gently.

Note

When the cover is removed, be sure not to touch the

speaker units with your hands or to exert excessive

force with tools.

Removing the front cover

Main/rear/rear center (for NS-P436)

Center

䡵 Mounting the main/rear speakers (and rear center speaker for

NS-P436) by using commercially available speaker stands or

brackets

Using the Yamaha Speaker Stand SPS-10MM (option)

By using the Yamaha Speaker Stand

SPS-10MM, speakers can be placed

on the floor. (Two stands make a set.)

* The SPS-10MM is not available in some areas.

60 mm

You can also use the screw holes on the bottom of the

speaker for installing the speakers on commericially

available speaker stands (if you do not use the

attached mounting brackets.)

A screw with a diameter of 4 mm

can be used.

(Hole depth : 10 mm)

SPS-10MM

NS-P430-436 (UB) 03.2.28, 7:02 PM6

English

E-7

SPEAKERS

MAIN

OUTPUT

SUB

WOOFER

CENTER

REAR CENTER

—

REAR

(SURROUND)

INPUT

/MONO

OFF LOW HIGH

AUTO

STANDBY

NORM REV

PHASE

POWER

OFF

110V

–

120V 220V

–

240V

VOLTAGE

SELECTOR

INPUT

/MONO

OFF LOW HIGH

AUTO

STANDBY

NORM REV

PHASE

CENTER CENTER

FRONT R

FRONT LFRONT L

REAR C

REAR R

REAR L

REAR R

CONNECTIONS

Caution: Plug in the subwoofer and other audio/video components after all connections are

completed.

䡵 An example of basic connections

Subwoofer

Amplifier

To AC outlet

Center speaker

Rear speaker

Right

LeftRight

Main speakers

Rear center speaker

(for NS-P436)

Rear speaker

Left

NS-P430-436 (UB) 03.2.28, 7:02 PM7

E-8

● Connect the main, center and rear speakers (and rear

center speaker for NS-P436) to the speaker output

terminals of your amplifier with the provided speaker

cables.

* The provided speaker cables have labels marked

FRONT L, FRONT R, CENTER, REAR L, REAR R

(and REAR C for NS-P436). Connect each speaker

cable to the corresponding speaker by following the

figure on page 7.

(The speaker cables marked FRONT L/R are used for

connecting the main speakers to the MAIN speakers’

terminals on the amplifier.)

* Connect each speaker making sure not to reverse the

polarity (+, –). If the speaker is connected with

reversed polarity, the sound will be unnatural and lack

bass.

* For the main and rear speakers only, connect one

speaker to the left (marked L) terminals of your

amplifier, and another speaker to the right (marked R)

terminals.

● Connect the subwoofer to the line output (pin jack)

terminal(s) of the amplifier.

* To connect with a YAMAHA DSP amplifier (or AV

receiver), connect the SUBWOOFER (or LOW PASS

etc.) terminal on the rear of the DSP amplifier (or AV

receiver) to the L/MONO INPUT terminal of the

subwoofer.

* To connect the subwoofer to the SPLIT SUBWOOFER

terminals on the rear of the DSP amplifier, connect

them to both the left L/MONO and right R INPUT

terminals of the subwoofer.

Note

When connecting to a monaural line output terminal of the

amplifier, connect to the L/MONO INPUT terminal.

NS-P430-436 (UB) 03.2.28, 7:02 PM8

English

E-9

Main speakers

Center speaker

Use the provided speaker cables (4 m). One side of the

speaker cable is red and the other side is black.

Connect the (+) terminals on both the speaker and the

amplifier using the red side of the cable. Connect the (–)

terminals on both components using the black side.

Red: positive (+)

Black: negative (–)

Rear speakers

Rear center speaker (for NS-P436)

Use the provided speaker cables (15 m). One side of the

speaker cable has a gray line and the other side has no line.

Connect the (+) terminals on both the speaker and the

amplifier using the side with a gray line. Connect the (–)

terminals on both components using the side with no line.

Red: positive (+)

Black: negative (–)

䡵 How to connect speaker cables to the input terminals of the

speakers

For connections, keep the speaker cables as short as possible. Do not bundle or roll up the excess part of the cables. If the

connections are faulty, no sound will be heard from the speakers.

Before connecting

Remove the insulation coating at the extremity of each

speaker cable by twisting the coating off.

How to Connect:

1 Press and hold the terminal’s tab, as shown in the

figure.

2 Insert the bare wire.

3 Release your finger from the tab to allow it to lock

securely on the cable’s wire end.

4 Test the firmness of the connection by pulling lightly on

the cable at the terminal.

Note

Do not let the bare speaker wires touch each other as

this could damage the speaker or the amplifier, or both

of them.

Gray line

Red

Black

NS-P430-436 (UB) 03.2.28, 7:03 PM9

E-10

USING THE SUBWOOFER (YST-SW015)

䡵 Controls and their functions

1 Power indicator

Lights up in green while the subwoofer is on.

Lights up in red while the subwoofer is set in the

standby mode by the operation of the automatic power-

switching function.

Goes off when the subwoofer is set in the standby

mode.

2 STANDBY/ON button

Press this button to turn on the power when the

POWER (

7) switch is set in the ON position. (The

power indicator lights up in green.)

Press again to set the subwoofer in the standby mode.

(The power indicator goes off.)

Standby mode

The subwoofer is still using a small amount of power

in this mode.

3 B.A.S.S. (Bass Action Selector System) button

When this button is pressed in to the MUSIC position,

the bass sound in audio software is well reproduced.

By pressing the button again so that it pops out at the

MOVIE position, the bass sound in video software is

well reproduced.

INPUT

/MONO

OFF LOW HIGH

AUTO

STANDBY

NORM REV

PHASE

POWER

OFF

110V

–

120V 220V

–

240V

VOLTAGE

SELECTOR

SUBWOOFER SYSTEM YST-SW015

STANDBY/ON B.A.S.S. HIGH CUT

–

150Hz

VOLUME

–

INPUT

/MONO

OFF LOW HIGH

AUTO

STANDBY

NORM REV

PHASE

SUBWOOFER SYSTEM YST-SW015

STANDBY/ON B.A.S.S. HIGH CUT

–

150Hz

VOLUME

–

POWER

OFF

110V

–

120V 220V

–

240V

VOLTAGE

SELECTOR

24513

98 0

Rear panel (General model)

Front panel

Port

4 HIGH CUT control

Adjusts the high frequency cut off point.

Frequencies higher than the frequency selected by this

control are all cut off (and no output).

* One graduation of this control represents 10 Hz.

5 VOLUME control

Adjusts the volume level. Turn the control clockwise to

increase the volume, and counterclockwise to

decrease the volume.

6 VOLTAGE SELECTOR switch

(For China, Korean and General models)

If the preset setting of the switch is incorrect, set the

switch to the proper voltage range (220V-240V or

110V-120V) of your area.

Consult your dealer if you are unsure of the correct

setting.

WARNING

Be sure to unplug the subwoofer before setting the

VOLTAGE SELECTOR switch correctly.

MOVIE MUSIC

50 Hz

60 Hz

70 Hz

80 Hz

90 Hz

140 Hz

130 Hz

120 Hz

110 Hz

100 Hz

150 Hz

NS-P430-436 (UB) 03.2.28, 7:03 PM10

English

E-11

7 POWER switch

Normally, set this switch to the ON position to use the

subwoofer. In this state, you can turn on the subwoofer

or turn the subwoofer into the standby mode by

pressing the STANDBY/ON (

2) button. Set this switch

to the OFF position to completely cut off the

subwoofer’s power supply from the AC line.

8 INPUT terminals

Used to input line level signals from the amplifier.

(Refer to “CONNECTIONS” for details.)

9 AUTO STANDBY (HIGH/LOW/OFF) switch

This switch is originally set to the OFF position. By

setting this switch to the HIGH or LOW position, the

subwoofer’s automatic power-switching function

operates as described below. If you do not need this

function, leave this switch in the OFF position.

* Make sure to change the setting of this switch only

when the subwoofer is set in the standby mode by

pressing the STANDBY/ON (

2) button.

0 PHASE switch

Normally this switch is to be set to the REV (reverse)

position. However, according to the listening condition

or your preference, there may be a case when better

sound quality is obtained by setting this switch to the

NORM (normal) position. Select the better position by

monitoring the sound.

If the source being played is stopped and the input signal is

cut off for 7 to 8 minutes, the subwoofer automatically

switches to the standby mode. (When the subwoofer

switches to the standby mode by the automatic power-

switching function, the power indicator lights up in red.)

When you play a source again, the power of the subwoofer

turns on automatically by sensing audio signals input to the

subwoofer.

This function operates by sensing a certain level of low

frequency input signal. Usually set the AUTO STANDBY

switch to the LOW position. However, if this function does

not operate smoothly, set the switch to the HIGH position. In

the HIGH position, the power will turn on even with a low

level of input signal. But please be aware that the subwoofer

may not switch to the standby mode when there is an

extremely low input signal.

* The power might turn on unexpectedly by sensing noise

from other appliances. If that occurs, set the AUTO

STANDBY switch to the OFF position and use the

STANDBY/ON button to switch the power between on

and in the standby mode manually.

* This function detects the low-frequency components

below 200 Hz of the input signals (i.e., the explosion in

the action movie, the sound of the bass guitar or the bass

drum, etc.).

* The minutes required to switch the subwoofer to the

standby mode might change by sensing noise from other

appliances.

This function is available only when the power of the

subwoofer is on (by pressing the STANDBY/ON button).

䡵 Automatic power-switching function

NS-P430-436 (UB) 03.2.28, 7:03 PM11

E-12

1 Set the VOLUME control to minimum (0).

2 Turn on the power of all the other

components.

3 Make sure that the POWER switch is set to

the ON position, then press the STANDBY/

ON button to turn on the subwoofer.

* The Power indicator lights up in green.

4 Play a source containing low-frequency

components and adjust the amplifier’s

volume control to the desired listening level.

5 Adjust the HIGH CUT control to the position

where the desired response can be

obtained.

This system is designed so that the optimum tone

balance between the subwoofer and the main speakers

(NX-430P) is obtained when this control is set at 110

Hz. However, the tone balance may change depending

on the room size, the distance from the subwoofer to

the main speakers, etc. So, if you prefer, turn the HIGH

CUT control and set it to a position where a better tone

balance is obtained.

6 Increase the volume gradually to adjust the

volume balance between the subwoofer and

the main speakers.

䡵 Adjusting the subwoofer before use

Before using the subwoofer, adjust the subwoofer to obtain the optimum volume and tone balance between the subwoofer and

the main speakers by following the procedures described below.

7 Set the PHASE switch to the position which

gives you the better bass sound.

Normally, set the switch to the REV (reverse) position. If

the desired response cannot be obtained, set the switch

to the NORM (normal) position.

8 Select “MOVIE” or “MUSIC” according to the

played source.

MOVIE: When a movie type source is played, the low-

frequency effects are enhanced to allow the listener

enjoy more powerful sound. (The sound will be thicker

and deeper.)

MUSIC: When an ordinary music source is played, the

excessive low-frequency components are cut off to

make the sound clearer. (The sound will be lighter and

reproduces the melody line more clearly.)

• Once the volume balance between the subwoofer and

the main speakers is adjusted, you can adjust the

volume of your whole sound system by using the

amplifier’s volume control.

However, if you change the main speakers NX-430P

to others, you must make this adjustment again.

• For adjusting the VOLUME control, the HIGH CUT

control and the PHASE switch, refer to “Frequency

characteristics” on the next page.

INPUT

/MONO

OFF LOW HIGH

AUTO

STANDBY

NORM REV

PHASE

POWER

OFF

110V

–

120V 220V

–

240V

VOLTAGE

SELECTOR

SUBWOOFER SYSTEM YST-SW015

STANDBY/ON B.A.S.S. HIGH CUT

–

150Hz

VOLUME

–

INPUT

/MONO

OFF LOW HIGH

AUTO

STANDBY

NORM REV

PHASE

SUBWOOFER SYSTEM YST-SW015

STANDBY/ON B.A.S.S. HIGH CUT

–

150Hz

VOLUME

–

POWER

OFF

1, 6583

Rear panel

Front panel

NS-P430-436 (UB) 03.2.28, 7:03 PM12

English

E-13

䡵 Frequency characteristics

Adjustment of the VOLUME control, the HIGH CUT control and the PHASE switch should be changed depending on the room

size, the distance from the subwoofer to the main speakers, sources, etc.

Following figures show the optimum adjustment of each control and the frequency characteristics when this subwoofer is

combined with NX-430P.

Frequency characteristics of this subwoofer

(YST-SW015)

●

When combined with NX-430P

PHASE–Set to the REV

(reverse) position.

B.A.S.S.–MOVIE

HIGH CUT50

–

150Hz VOLUME

–

100

YST-SW015

NX-430P

NS-P430-436 (UB) 03.2.28, 7:03 PM13

E-14

ADVANCED YAMAHA ACTIVE SERVO TECHNOLOGY

(for YST-SW015)

The theory of Yamaha Active Servo Technology has been

based upon two major factors, the Helmholtz resonator and

negative-impedance drive. Active Servo Processing

speakers reproduce the bass frequencies through an “air

woofer”, which is a port or opening in the speaker’s cabinet.

This opening is used instead of, and performs the functions

of, a woofer in a conventionally designed speaker system.

Thus, signals of low amplitude within the cabinet can,

according to the Helmholtz resonance theory, be outputted

from this opening as waves of great amplitude if the size of

the opening and the volume of the cabinet are in the correct

proportion to satisfy a certain ratio.

In order to accomplish this, moreover, the amplitudes within

the cabinet must be both precise and of sufficient power

because these amplitudes must overcome the “load”

presented by the air that exists within the cabinet.

Thus it is this problem that is resolved through the employ-

ment of a new design in which the amplifier supplies special

signals. If the electrical resistance of the voice coil could be

reduced to zero, the movement of the speaker unit would

become linear with respect to signal voltage. To accomplish

this, a special negative-impedance output-drive amplifier for

subtracting output impedance of the amplifier is used.

By employing negative-impedance drive circuits, the

amplifier is able to generate precise, low-amplitude, low-

frequency waves with superior damping characteristics.

These waves are then radiated from the cabinet opening as

high-amplitude signals. The system can, therefore, by

employing the negative-impedance output drive amplifier

and a speaker cabinet with the Helmholtz resonator,

reproduce an extremely wide range of frequencies with

amazing sound quality and less distortion.

The features described above, then, are combined to be the

fundamental structure of the conventional Yamaha Active

Servo Technology.

Our new Active Servo Technology — Advanced Yamaha

Active Servo Technology — adopted Advanced Negative

Impedance Converter (ANIC) circuits, which allows the

conventional negative impedance converter to dynamically

vary in order to select an optimum value for speaker

impedance variation. With this new ANIC circuits, Advanced

Yamaha Active Servo Technology can provide more stable

performance and improved sound pressure compared with

the conventional Yamaha Active Servo Technology, resulting

in more natural and dynamic bass reproduction.

High-amplitude

bass sound

Cabinet

Port

Air woofer

(Helmholtz resonator)

Active Servo

Processing

Amplifier

Signals

Signals of low amplitude

Advanced Negative-

impedance Converter

NS-P430-436 (UB) 03.2.28, 7:03 PM14

English

E-15

Problem

No sound.

Sound level is too low.

What to Do

Connect them securely.

Connect them correctly, that is L (left) to

L, R (right) to R, “+” to “+” and “–” to “–”.

Cause

Speaker cables are not connected

securely.

Speaker cables are not connected

correctly.

TROUBLESHOOTING

Refer to the chart below when this unit does not function properly. If the problem you are experiencing is not listed below or if

the instructions given below do not help, disconnect the power cord and contact your authorized YAMAHA dealer or service

center.

Problem

Power is not supplied even

though the STANDBY/ON button

is set to the ON position.

No sound.

Sound level is too low.

The subwoofer does not turn on

automatically.

The subwoofer does not turn into

the standby mode automatically.

The subwoofer turns into the

standby mode unexpectedly.

The subwoofer turns on

unexpectedly.

What to Do

Connect it securely.

Set the POWER switch to the ON

position.

Turn the VOLUME control to the right.

Connect them securely.

Connect them correctly, that is L (left) to

L, R (right) to R, “+” to “+” and “–” to “–”.

Set the switch to the other position.

Play a source sound with bass

frequencies.

Set the HIGH CUT control to a higher

position.

Reposition the subwoofer or break up

the parallel surface by placing

bookshelves etc. along the walls.

Set the POWER switch to the ON

position.

Set the STANDBY/ON button to the ON

position.

Set the AUTO STANDBY switch to the

“HIGH” or “LOW” position.

Set the AUTO STANDBY switch to the

“HIGH” position.

Move the subwoofer further away from

such appliances and/or reposition the

connected speaker cables.

Otherwise, set the AUTO STANDBY

switch to the “OFF” position.

Set the AUTO STANDBY switch to the

“HIGH” or “LOW” position.

Set the AUTO STANDBY switch to the

“HIGH” position.

Move the subwoofer farther away from

such appliances and/or reposition the

connected speaker cables.

Otherwise, set the AUTO STANDBY

switch to the “OFF” position.

Cause

The power plug is not securely

connected.

The POWER switch is set to the OFF

position.

The VOLUME control is set to 0.

Speaker cables are not connected

securely.

Speaker cables are not connected

correctly.

Setting of the PHASE switch is not

proper.

A source sound with few bass

frequencies is played.

It is influenced by standing waves.

The POWER switch is set to the OFF

position.

The STANDBY/ON button is set to the

OFF position.

The AUTO STANDBY switch is set to

the OFF position.

The level of input signal is too low.

There is an influence of noise

generated from external appliances etc.

The AUTO STANDBY switch is set to

the OFF position.

The level of input signal is too low.

There is an influence of noise

generated from external appliances etc.

For YST-SW015

NS-P430-436 (UB) 03.2.28, 7:03 PM15

E-16

SPECIFICATIONS

䡵 NX-430P, NX-C430

Type ............... 2-way acoustic-suspension speaker system

Magnetic shielding type

Driver

<NX-430P> ....................... Coaxial 2-way [5 cm (2”) cone

and 1.3 cm (1/2”) dome] speaker x 1

5 cm (2”) full range cone speaker x 1

<NX-C430> ...................... Coaxial 2-way [5 cm (2”) cone

and 1.3 cm (1/2”) dome] speaker x 1

5 cm (2”) full range cone speaker x 2

Nominal Input Power ................................................. 30W

Maximum Input Power ............................................. 100W

Impedance ..................................................................... 6Ω

Frequency Response ............................... 70 Hz to 60 kHz

Sensitivity

<NX-430P> ............................................... 85 dB/2.83V/m

<NX-C430> .............................................. 86 dB/2.83V/m

Dimensions (W x H x D)

<NX-430P> .......................... 87 mm x 184 mm x 147 mm

(3-7/16” x 7-1/4” x 5-13/16”)

<NX-C430> ......................... 273 mm x 81 mm x 147 mm

(10-3/4” x 3-3/16”x 5-13/16”)

Weight

<NX-430P> ...................................... 1.2 kg (2 lbs. 10 oz.)

<NX-C430> ..................................... 1.7 kg (3 lbs. 12 oz.)

䡵 YST-SW015

Type ............... Advanced Yamaha Active Servo Technology

Magnetic shielding type

Driver ....................................... 16 cm (6-1/2”) cone woofer

Amplifier Output .................................................. 70 W/5Ω

Frequency Response ...............................30 Hz to 200 Hz

Power Supply

U.S.A. and Canada models .................... AC 120V, 60 Hz

U.K. and Europe models ........................ AC 230V, 50 Hz

Australia model ....................................... AC 240V, 50 Hz

China, Korean and General models

....................................... AC 110-120/220-240V, 50/60 Hz

Power Consumption ................................................. 70 W

Standby Power Consumption ................................. 0.8 W

Dimensions (W x H x D) ..... 280 mm x 325 mm x 320 mm

(11” x 12-13/16” x 12-5/8”)

Weight ................................................ 9.2 kg (20 lbs. 4 oz.)

* Specifications are subject to change without notice due to

product improvements.

YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.

YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA

YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, F.R. OF GERMANY

YAMAHA ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE

YAMAHA ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD1 7JS, ENGLAND

YAMAHA SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN

YAMAHA MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA

Printed in Indonesia WA31510-2

NS-P430-436 (UB) 03.3.3, 2:10 PM16

Yamaha NX-C430 Bruksanvisning

varumärke: Yamaha

Modell: NX-C430

Kategori: Bärbara högtalare

Typ: Bruksanvisning

Denna manual är också lämplig för

Ladda ner pdf

Rapportera

på andra språk

italiano: Yamaha NX-C430 Manuale del proprietario
čeština: Yamaha NX-C430 Návod k obsluze
español: Yamaha NX-C430 El manual del propietario
Deutsch: Yamaha NX-C430 Bedienungsanleitung
polski: Yamaha NX-C430 Instrukcja obsługi
português: Yamaha NX-C430 Manual do proprietário
français: Yamaha NX-C430 Le manuel du propriétaire
Türkçe: Yamaha NX-C430 El kitabı
English: Yamaha NX-C430 Owner's manual
dansk: Yamaha NX-C430 Brugervejledning
русский: Yamaha NX-C430 Инструкция по применению
suomi: Yamaha NX-C430 Omistajan opas
Nederlands: Yamaha NX-C430 de handleiding
română: Yamaha NX-C430 Manualul proprietarului

Yamaha NX-C430 Bruksanvisning

Denna manual är också lämplig för

Yamaha NX-C430 Bruksanvisning

på andra språk

Relaterade papper