Toro eHoverPro 450 Användarmanual

Form No. 3466-205 Rev B

eHoverPro™ 450 60V Mower

02614T

eHoverPro™ 450 60 V -plæneklipper

02614T

eHoverPro™ 450 60 V Mäher

02614T

Segadora eHoverPro™ 450 60 V

02614T

T ondeuse eHoverPro™ 450 de 60 V

02614T

T osaerba eHoverPro™ 450 60 V

02614T

eHoverPro™ 450 60V maaier

02614T

eHoverPro™ 450 60 V -gressklipper

02614T

Cortador eHoverPro™ 450 60 V

02614T

eHoverPro™ 450-gräsklippare på 60 V

02614T

www .T oro.com.

*3466-205*

Form No. 3465-914 Rev B

eHoverPro

T M

450 60V Mower

Model No. 02614T —Serial No. 400000000 and Up

Register at www .T oro.com.

Original Instructions (EN)

*3465-914*

W ARNING

CALIFORNIA

Proposition 65 W arning

The power cord on this product contains

lead, a chemical known to the State

of California to cause birth defects

or other reproductive harm. W ash

hands after handling.

Use of this product may cause exposure

to chemicals known to the State of

California to cause cancer , birth defects,

or other reproductive harm.

Introduction

This machine is intended to be used by hired,

commercial operators for maintaining turf on slopes,

tight undulations, areas near water , or bunker lips. It

is designed to use T oro 60V lithium-ion battery packs.

These battery packs are designed to be charged only

by T oro 60V lithium-ion battery chargers. Using this

product for purposes other than its intended use could

prove dangerous to you and bystanders.

Read this information carefully to learn how to operate

and maintain your product properly and to avoid

injury and product damage. Y ou are responsible for

operating the product properly and safely .

V isit www .https://www .toro.com/en-GB for more

information, including safety tips, training materials,

accessory information, help nding a dealer , or to

register your product.

Whenever you need service, genuine T oro parts, or

additional information, contact an Authorized Service

Dealer or T oro Customer Service and have the model

and serial numbers of your product ready . Figure 1

identies the location of the model and serial numbers

on the product. W rite the numbers in the space

provided.

Important: W ith your mobile device, you can

scan the QR code on the serial number decal (if

equipped) to access warranty , parts, and other

product information.

g414362

Figure 1

1. Model and serial number location

W rite the product model and serial numbers in the

space below:

Model No.

Serial No.

Safety-Alert Symbol

The safety-alert symbol ( Figure 2 ) shown in this

manual and on the machine identies important safety

messages that you must follow to prevent accidents.

g000502

Figure 2

Safety-alert symbol

The safety-alert symbol appears above information

that alerts you to unsafe actions or situations and

is followed by the word DANGER ,W ARNING , or

CAUTION .

DANGER indicates an imminently hazardous situation

which, if not avoided, will result in death or serious

injury .

W ARNING indicates a potentially hazardous situation

which, if not avoided, could result in death or serious

injury .

81 1 1 L yndale A venue South

Bloomington, MN 55420

2

Contact us at www .T oro.com.

Printed in the UK

CAUTION indicates a potentially hazardous situation

which, if not avoided, may result in minor or moderate

injury .

This manual uses two other words to highlight

information. Important calls attention to special

mechanical information and Note emphasizes general

information worthy of special attention.

Contents

Safety-Alert Symbol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

IMPOR T ANT SAFETY INSTRUCTIONS . . . . . . . . . . . . 3

Safety and Instructional Decals . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

1 Installing the Handlebar Footstop . . . . . . . . . . . . . . . . . . . . . 8

2 Installing the Handlebar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Product Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Specications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Charging, Operation, and Storage

T emperature Ranges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Attachments/Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Before Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Inserting the Battery Pack into the

Machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

During Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Running the Machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Shutting Of f the Machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Removing the Battery Pack from the

Machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Supporting the Handlebar with the

Footstop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Adjusting the Cutting Height . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Operating T ips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

After Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Charging the Battery Pack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Recommended Maintenance Schedule(s) . . . . . . . . . . . 19

Preparing for Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Blade Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Cleaning the Machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Preparing the Machine for Storage . . . . . . . . . . . . . . . . . . . 21

Preparing the Machine for the Operation . . . . . . . . . . . 21

T roubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Safety

IMPORT ANT SAFETY

INSTRUCTIONS

W ARNING

When using electric lawn mowers, basic

safety precautions should always be followed

to reduce the risk of re, electric shock, and

personal injury , including the following:

Read All Instructions

I. T raining

1. The operator of the machine is responsible for

any accidents or hazards occurring to others or

their property .

2. Do not allow children to use or play with the

machine, battery pack, or the battery charger;

local regulations may restrict the age of the

operator .

3. Do not allow children or untrained people to

operate or service this device. Allow only people

who are responsible, trained, familiar with the

instructions, and physically capable to operate

or service the device.

4. Before using the machine, battery pack, and

battery charger , read all the instructions and

cautionary markings on these products.

5. Become familiar with the controls and proper

use of the machine, battery pack, and battery

charger .

II. Preparation

1. Keep bystanders, especially children and pets,

out of the operating area.

2. Do not operate the machine without all guards

and safety devices, such as deectors and grass

catchers, in place and functioning properly on

the machine.

3. Inspect the area where you will use the machine

and remove all objects that could interfere with

the operation of the machine or that the machine

could throw .

4. Before using the machine, ensure that the blade,

blade bolt, and blade assembly are not worn or

damaged. Replace any damaged or unreadable

labels.

5. Use only the battery pack specied by T oro.

Using other accessories and attachments may

increase the risk of injury and re.

6. Plugging the battery charger into an outlet

that is not of the proper voltage can cause a

3

re or electric shock. For a dif ferent style of

connection, use an attachment plug adapter of

the proper conguration for the power outlet if

needed.

7. Do not use a damaged or modied battery

pack or battery charger , which may exhibit

unpredictable behavior that results in re,

explosion, or risk of injury .

8. If the supply cord to the battery charger is

damaged, contact an authorized T oro distributor

to replace it.

9. Charge the battery pack with only the battery

charger specied by T oro. A charger suitable for

1 type of battery pack may create a risk of re

when used with another battery pack.

10. Charge the battery pack in a well-ventilated area

only .

1 1. Follow all charging instructions and do

not charge the battery pack outside of the

temperature range specied in the instructions.

Otherwise, you may damage the battery pack

and increase the risk of re.

12. Dress properly—W ear appropriate clothing,

including eye protection; long pants; substantial,

slip-resistant footwear (not barefoot or wearing

sandals); and hearing protection. T ie back long

hair and do not wear loose clothing or loose

jewelry that can get caught in moving parts.

W ear a dust mask in dusty operating conditions.

Use of rubber gloves is recommended.

III. Operation

1. Contact with the moving blade will cause serious

injury . Keep your hands and feet away from the

cutting area and all moving parts of the machine.

Keep clear of any discharge opening.

2. Using this machine for purposes other than its

intended use could prove dangerous to you and

bystanders.

3. Disengage the self-propel drive (if equipped)

before starting the machine.

4. Do not tilt the machine when starting the motor .

5. Prevent unintentional starting—Ensure that

the electric-start button is removed from the

electric-start switch before connecting the

battery pack and handling the machine.

6. Use your full attention while operating the

machine. Do not engage in any activity that

causes distractions; otherwise, injury or property

damage may occur .

7. Stop the machine, remove the electric-start

button, wait for all movement to stop, and

remove the battery pack from the machine

before adjusting, servicing, cleaning, or storing

the machine.

8. Remove the battery pack and electric-start

button from the machine whenever you leave it

unattended or before changing accessories.

9. Do not force the machine—Allow the machine to

do the job better and safer at the rate for which it

was designed.

10. Stay alert—W atch what you are doing and use

common sense when operating the machine.

Do not use the machine while ill, tired, or under

the inuence of alcohol or drugs.

1 1. Do not use a battery-operated lawn mower in

rain.

12. Operate the machine only in good visibility and

appropriate weather conditions. Do not operate

the machine when there is the risk of lightning.

13. Use extreme caution when reversing or pulling

the machine toward you.

14. Keep proper footing and balance at all times,

especially on slopes. Mow across the face

of slopes, never up and down. Use extreme

caution when changing directions on slopes. Do

not mow on slopes more than 45 ° . W alk, never

run with the machine.

15. Do not direct the discharge material toward

anyone. A void discharging material against a

wall or obstruction; material may ricochet toward

you. Stop the blade(s) when crossing surfaces

other than grass.

16. W atch for holes, ruts, bumps, rocks, or other

hidden objects. Uneven terrain could cause you

to lose your balance or footing.

17. W et grass or leaves can cause serious injury if

you slip and contact the blade. Do not mow in

wet conditions. Do not mow when it is raining.

18. If the machine strikes an object or starts to

vibrate, immediately shut of f the machine,

remove the electric-start button, wait for all

movement to stop, and remove the battery pack

before examining the machine for damage.

Make all necessary repairs before resuming

operation.

19. Stop the machine and remove the electric-start

button before loading the machine for hauling.

20. Under abusive conditions, the battery pack may

eject liquid; avoid contact. If you accidently

come into contact with the liquid, ush with

water . If the liquid contacts your eyes, seek

medical help. Liquid ejected from the battery

pack may cause irritation or burns.

IV . Maintenance and Storage

1. Stop the machine, remove the electric-start

button, wait for all movement to stop, and

remove the battery pack from the machine

4

before adjusting, servicing, cleaning, or storing

the machine.

2. Do not attempt to repair the machine except as

indicated in the instructions. Have an authorized

T oro distributor perform service on the machine

using identical replacement parts.

3. W ear gloves and eye protection when servicing

the machine.

4. Sharpen a dull blade on both edges to maintain

balance. Clean the blade and ensure that it is

balanced.

5. Replace the blade if it is bent, worn, or cracked.

An unbalanced blade causes vibration, which

could damage the motor or cause personal

injury .

6. When servicing the blade, be aware that the

blade can still move even though the power

source is of f.

7. For best performance, use only genuine T oro

replacement parts and accessories. Other

replacement parts and accessories could be

dangerous, and such use could void the product

warranty .

8. Maintain the machine—Keep cutting edges

sharp and clean for the best and safest

performance. Keep handles dry , clean, and free

from oil and grease. Keep guards in place and

in working order . Keep the blade sharp. Use an

identical replacement blade only .

9. Check the machine for damaged parts—If there

are damaged guards or other parts, determine

whether the machine will operate properly .

Check for misaligned and binding moving parts,

broken parts, mounting, and any other condition

that may af fect its operation. Unless indicated

in the instructions, have an authorized T oro

distributor repair or replace a damaged guard

or part.

10. When the battery pack is not in use, keep it

away from metal objects such as paper clips,

coins, keys, nails, and screws that can make a

connection from 1 terminal to another . Shorting

the battery terminals may cause burns or a re.

1 1. Check the blade and motor mounting bolts

frequently for tightness.

12. When you are not using the machine, store it

indoors in a dry , secure place out of the reach

of children.

13. Do not expose a battery pack or machine to re

or excessive temperature. Exposure to re or

temperature above 130°C (265°F) may cause

explosion.

14. CAUTION—A mistreated battery pack may

present a risk of re, explosion, or chemical

burn.

•Do not disassemble the battery pack.

•Replace the battery pack with a genuine

T oro battery pack only; using another type of

battery pack may cause a re or risk of injury .

•Keep battery packs out of the reach of

children and in the original packaging until

you are ready to use them.

SA VE THESE

INSTRUCTIONS

5

Safety and Instructional Decals

Safety decals and instructions are easily visible to the operator and are located near any area

of potential danger . Replace any decal that is damaged or missing.

decal1 1 1-9826

1 1 1–9826

1. Cutting/dismemberment

hazard of hand or foot,

cutting unit—keep your

hands and feet away from

moving parts.

2. Read the Operator ’ s

Manual .

decal133-8054

133-8054

decal94-8072

94-8072

g017410

H295159

1. Engine stop (shut of f)

decal134-4551

134-4551

1. Read the Operator ’ s

Manual for more

information on starting

the machine.

3. T o shut of f the machine,

release the blade-control

bar .

2. T o start the machine, insert

the electric-start button

into the electric-start

switch, squeeze the

blade-control bar to the

handle, and press the

electric-start button.

6

decal134-8067

134-8067

1. W arning—read the Operator ’ s Manual ; all operators should

be trained before operating the machine.

4. W arning—read the Operator ’ s Manual .

2. W arning—wear hearing protection and eye protection.

5. Cutting/dismemberment hazard of hands or feet, mower

blade—shut of f the machine and remove the key before

performing maintenance; stay away from moving parts.

3. Thrown object hazard—keep bystanders away .

7

Setup

1

Installing the Handlebar

Footstop

Parts needed for this procedure:

1 Lower handlebar

1 Footstop

2

W asher (6 mm)

1

Locknut (6 mm)

Procedure

Note: Y ou can only use the footstop to support the

handlebar in the vertical position when you assemble

the handlebar in the lower position 103.4 cm (40-3/4

inches).

g414363

Figure 3

1. Low-handlebar position 3. Footstop

2. Upstop bracket 4. High-handlebar position

1. Determine the handlebar height when the

footstop is secured to the upstop bracket ( Figure

3).

2. Align the hole in the footstop with the bolt in the

lower handlebar ( Figure 4 ).

g462033

Figure 4

1. Lower handlebar

3. W asher (6 mm)

2. Footstop

4. Locknut (6 mm)

3. Assemble the footstop to the handlebar with 2

washers (6 mm) and a locknut (6 mm).

4. T ighten the locknut.

Note: Ensure that you can pivot the footstop.

8

2

Installing the Handlebar

Parts needed for this procedure:

4 T -bushings

2

Bolt (6 x 55 mm)

7

W asher (6 mm)

2

Locknut (6 mm)

1 Upper handlebar

2 U-bolt

2 Knob

1 Pan-head screw

1

Cable clamp

1 Locknut

2

Cable tie

Assembling the Lower Handlebar

to the Machine

1. Assemble 2 T -bushings into the handlebar

anges of the mower deck ( Figure 5 ).

g3671 17

Figure 5

1. T -bushings

2. Handlebar anges (mower

deck)

2. Align the footstop of the handlebar to the up-stop

bracket on the deck ( Figure 6 ).

g414364

Figure 6

1. Up-stop bracket 2. Footstop

3. Align the hole in the handlebar with the holes in

the bushings ( Figure 7 ), and secure handlebar ,

to the machine with a bolt (6 x 55 mm), 2

washers (6 mm), and a locknut (6 mm).

g367302

Figure 7

1. Lower handlebar

3. W asher (6 mm)

2. Bolt (6 x 55 mm) 4. Locknut (6 mm)

4. Repeat step 3at the other side of the machine.

Assembling the Upper and Lower

Handlebars

1. Align the holes on the upper handlebar with the

holes in the lower handlebar ( Figure 8 ).

9

g364684

Figure 8

1. Lower handlebar 4. Upper handlebar

2. Knob 5. U-bolt

3. W asher (6 mm)

2. Assemble the upper handlebar to the lower

handlebar wit the 2 U-bolts, 2 washer (6 mm),

and 2 knobs.

Assembling the Cable to the

Operator-Presence Bail

1. Squeeze the leg of the operator-presence bail

until you can remove it from the upper handlebar ,

and remove the bail from the machine ( Figure 9 ).

g367353

Figure 9

2. Insert the cable tting through the hole in the

bracket of the operator-presence bail as shown

in Figure 10 .

g367914

Figure 10

1. Bracket

(operator-presence bail)

2. Cable tting

10

3. Insert the end of the operator-presence bail into

the handlebar , squeeze the other leg of bail

slightly , and insert the bail into the handlebar

(Figure 1 1 ).

g367358

Figure 1 1

Installing the Electric-Start Switch

1. Assemble the electric-start switch onto the

handlebar as shown ( Figure 12 ).

Note: Use the lower of the 2 mounting holes

on the handlebar .

g462046

Figure 12

1. Pan-head screw

5. Cable (operator-presence

bail)

2. Electric-start switch

6. Cable clamp

3. Upper handlebar 7. Locknut

4. Do not use this hole.

2. Align the cable for the operator-presence bail

to the upper cable groove of the electric-start

switch.

3. Align the cable clamp to the cable and switch.

4. Secure the clamp, cable, and switch to the upper

handlebar with the pan-head screw and locknut.

Securing Cables to the Handlebar

Secure the cables to the handlebar using cable ties

as shown in Figure 13 .

g465529

Figure 13

1. Cable tie

1 1

Product Overview

g414369

Figure 14

1. Handlebar 5. Mower deck

2. Operator-presence bail 6. Handlebar footstop

3. Electric-start button/switch

7. Handlebar knobs

4. Battery-compartment

cover

Controls

Operator-Presence Bail

The operator-presence bail ( Figure 14 ) controls the

power to the motor .

•Squeeze the bail to the handlebar to run the motor .

•Release the bail to the handlebar to shut of f the

motor .

Electric-Start Button

The electric-start button ( Figure 14 ) inserts into the

electric-start switch, and together they are used to

control the electric motor .

Specications

Machine Specication

Model

Cutting width

Product width

02614T

465 mm (18-1/2

inches)

575 mm (22-1/2

inches)

Charging, Operation, and Storage

T emperature Ranges

T emperature Range Specication

Charging or

Storing the

Battery Pack

Using the Battery

Pack

Using the

Machine

5°C (41°F) to 40°C

(104°F)*

-30°C (-22°F) to

49°C (120°F)*

0°C (32°F) to 49°C

(120°F)*

*Charging time may increase if you do not charge the

battery pack within the specied temperature range.

Store the machine, battery pack, and battery charger

in an enclosed, clean, and dry area.

Attachments/Accessories

A selection of T oro approved attachments and

accessories is available for use with the machine

to enhance and expand its capabilities. Contact

your Authorized Service Dealer or authorized T oro

distributor or go to www .T oro.com for a list of all

approved attachments and accessories.

T o ensure optimum performance and continued safety

certication of the machine, use only genuine T oro

replacement parts and accessories. Replacement

parts and accessories made by other manufacturers

could be dangerous.

12

Operation

Before Operation

Inserting the Battery Pack into the Machine

Important: Use the battery pack only in temperatures that are within the appropriate range; refer

to Specications ( page 12 )

1. Remove the electric-start button from the electric-start switch; refer to Running the Machine ( page 14 ) .

2. Check the battery pack to ensure that vents are clear of any dust and debris.

3. Open the battery-compartment cover ( Figure 15 ).

4. Align the electrical contacts of the battery pack with the electrical contacts in the battery compartment.

5. Assemble the battery pack onto the compartment-electrical contacts until the battery latches securely .

6. Close the battery-compartment cover .

Note: If the battery-compartment cover does not completely close, the battery is not fully inserted and

latched into the compartment.

g414371

Figure 15

1. Battery pack electrical contacts 2. Battery compartment electrical contacts

13

During Operation

Running the Machine

1. Insert the electric-start key into the electric-start

switch ( Figure 16 ).

g367528

Figure 16

2. Grasp the handlebar and operator presence bail

and close the bail against the handlebar ( Figure

16 ).

3. Push the starter-button.

4. Allow the motor to run at full speed before

moving the machine.

Shutting Off the Machine

1. Release the operator presence bail ( Figure 17 ).

g367527

Figure 17

2. Hold the handlebar while you wait for the motor

to stop.

3. Remove the electric-start key from the

electric-start switch.

14

Removing the Battery Pack from the Machine

1. Shut of f the machine; refer to Shutting Of f the Machine ( page 14 ) .

2. Open the battery-compartment cover ( Figure 18 ).

3. Press the battery-pack latch to release the battery pack and remove the battery pack.

4. Close the battery-compartment cover .

g414370

Figure 18

Supporting the Handlebar

with the Footstop

Handlebar Assembled in the

Lower Position

Note: If you assembled to the low-handlebar position

103 cm (40-1/2 inches), use the footstop to support

the handlebar in the vertical position.

g367257

Figure 19

1. Footstop rotated forward

2. Footstop rotated rearward

•T o release the handlebar , lift the handlebar and

rotate the footstop forward ( Figure 19 ).

•T o support the handlebar , position the handlebar

and rotate the footstop rearward.

Adjusting the Cutting

Height

W ARNING

Adjusting the cutting height may bring you

into contact with the moving blade, causing

serious injury .

• Release the operator-presence bail and

wait for all moving parts to stop.

• W ear cut-resistant gloves while handling

the blade.

Removing the Blade

1. Shut of f the machine, remove the electric-start

button, and remove the battery; refer to Shutting

Of f the Machine ( page 14 ) .

2. T ip the machine on its side.

g414372

Figure 20

3. Use a block of wood to hold the blade steady

(Figure 21 ).

15

g364888

Figure 21

4. Use a wrench to remove the blade by rotating

the bolt counterclockwise ( Figure 21 ).

Important: W ear safety glasses and

cut-resistant gloves when removing the

blade.

Positioning the Blade Spacers

Change the position of the spacers to adjust the

cutting height as shown in Figure 22 .

Note: Each spacer changes the cutting height of the

blade 6.3 mm (1/4 inch).

g364990

Figure 22

1. Conical spacer

4. Retainer

2. Spacers

5. Bolt

3. Blade

Installing the Blade

1. Align the curved ends of the blade toward mower

deck, and assemble the retainer , blade, spacers,

and conical spacer to the impeller with the bolt.

Important: Always assemble the conical

spacer directly below the impeller and the

retainer under the head of the bolt.

g364923

Figure 23

1. Impeller 3. Retainer

2. Conical spacer

4. Bolt

2. T orque the blade bolt to 75 N∙m (55 ft-lb).

Important: A bolt torqued to 75 N∙m (55 ft-lb)

is very tight. While holding the cutting blade

with block of wood, put your weight behind

the torque wrench, and tighten the bolt.

g364889

Figure 24

3. T ip the machine upright.

16

Operating T ips

General Mowing T ips

•Place the hoop of the footstop under the upstop to

increase handling of the machine.

g367278

Figure 25

•Inspect the area where you will use the machine

and remove all objects that the machine could

throw .

•A void striking solid objects with the blade. Never

deliberately mow over any object.

•If the machine strikes an object or starts to

vibrate, immediately shut of f the motor , remove

the electric-start key , and examine the machine

for damage.

•For best performance, ensure that the blade is

sharp before the cutting season begins.

•Replace a damaged blade with a new T oro

replacement blade.

Cutting Grass

•Cut only about a third of the grass blade at a time.

Do not cut below the highest setting (30 mm or

1-1/4 inches) unless the grass is sparse, or it is

late fall when grass growth begins to slow down.

•Do not mow grass over 15 cm (6 inches) long

because the machine may plug or the motor may

stall.

•W et grass and leaves tend to clump on the yard

and can cause the machine to plug or the motor to

stall. Mow only in dry conditions if possible.

W ARNING

W et grass or leaves can cause serious

injury if you slip and contact the cutting

blade.

Mow only in dry conditions if possible.

•Be aware of a potential re hazard in very dry

conditions, follow all local re warnings, and keep

the machine free of dry grass and leaf debris.

•If the nished lawn appearance is unsatisfactory ,

try 1 or more of the following:

– Inspect the cutting unit and/or replace the

cutting blade.

– W alk at a slower pace while mowing.

– Raise the cutting height on your machine.

– Cut the grass more frequently .

– Overlap cutting swaths instead of cutting a full

swath with each pass.

Cutting Leaves

•After cutting the lawn, ensure that half of the lawn

shows through the cut leaf cover . Y ou may need

to make more than a single pass over the leaves.

•Mowing grass over 15 cm (6 inches) in length is

not recommended. If the leaf cover is too thick, the

machine may plug and cause the motor to stall.

•Slow down your mowing speed if the machine

does not cut the leaves nely enough.

After Operation

Charging the Battery Pack

Important: The battery pack is not fully charged

when you purchase it. Before using the tool for

the rst time, place the battery pack in the charger

and charge it until the LED display indicates the

battery pack is fully charged. Read all safety

precautions.

Important: Charge the battery pack only at an

ambient temperature that are within the specied

temperature range; refer to Charging, Operation,

and Storage T emperature Ranges ( page 12 ) .

Note: At any time, press the battery-charge-indicator

button on the battery pack to display the current

charge (LED indicators).

1. Ensure that the vents on the battery and charger

are clear of any dust and debris.

17

g290533

Figure 26

1. Battery pack cavity 6. Handle

2. Battery pack venting areas

7. Charger LED indicator

light

3. Battery pack electrical

contacts

8. Charger venting areas

4. Battery-charge-indicator

button

9. Adapter charger

5. LED indicators (current

charge)

2. Line up the cavity in the battery pack ( Figure 26 )

with the tongue on the charger .

3. Slide the battery pack into the charger until it is

fully seated ( Figure 26 ).

4. W ait for the battery pack to charge; refer to

the following Battery Charger Status T able to

interpret the battery charger status.

Battery Charger Status T able

LED

indicator

light

Indicates

Of f

No battery pack is inserted

Green

blinking

Battery pack is charging

Green

Battery pack is charged

Red

Battery pack and/or battery charger is over or under

the specied temperature range*

Red

blinking

Battery pack charging fault**

*Refer to Charging, Operation, and Storage T emperature

Ranges ( page 12 ) for more information.

**Refer to T roubleshooting ( page 22 ) for more information.

Important: The battery can be left on the

charger for short periods between uses.

If the battery will not be used for longer

periods, remove the battery from the charger;

refer to Preparing the Machine for Storage

( page 21 ) .

5. T o remove the battery pack, pull the battery from

the charger .

18

Sidan laddas ...

Toro eHoverPro 450 Användarmanual

Toro eHoverPro 450 Användarmanual

på andra språk

Relaterade papper

Andra dokument