3M DBI-SALA® Window and Door Jamb Anchor 2100080, 1 EA Bruksanvisningar

USER INSTRUCTION MANUAL

5902273 REv. G

DOOR JAMB ANCHOR

Anchorage Connector

1

2100080

21.50 in. - 51.0 in.

(54.6 cm - 129.5 cm)

60.38 in.

(153.0 cm)

2.50 in.

(6.4 cm)

6.25 in.

(15.9 cm)

6.00 in.

(15.2 cm)

4.97 in.

(12.6 cm)

EN795:2012

Type B

CE Type Test

No. 2777

Satra Technology Europe Ltd

Bracetown Business Park

Clonee,

Dublin

D15 YN2P

Ireland

CE Product Quality Control

No. 2797

BSI

The Netherlands B.V.

Say Building

John M. Keynesplein 9

1066 EP

Amsterdam

Netherlands

ANSI Z359.18

Type A

OSHA 1926.502 OSHA 1910.140

2

A

C

B

E

D

F

60°

30°

3 4

C

B

A

FC

B

C

FC

5 6

A. B. C. D.

E. F. G.

A B C

3

7

1 2 3

8

A B

30°

4

9

B

A

B

Capacity: 1 Person, ANSI 310lbs (140kg) max, OSHA 420 lbs (190 kg) max.

Maximum arresting force 1800 lbs

Materials: Aluminum anchor; Zinc plated alloy steel D-ring

Standards: Meets ANSI Z359.18 Type A and OSHA 1926.502 & 1910.140

Minimum Breaking Strength: 5,000 lbs (22kN) MBS

ANSI Minimum Service Temp. -40F (-40C)

See User Manual for details on making connections. Do not allow lifeline to

abrade against sharp edges during use. Use caution when using this equipment near hazardous

thermal, electrical, or chemical sources. Refer to User Manual for additional information.

Inspect anchor before each use. At least monthly,

anchor should be inspected by a competent person in accordance with the User Manual.

Do not use if inspection reveals an unsafe or defective condition. Not user repairable.

This product is RFID enabled and contains an electronic tag that can be read

by compatible readers - providing inspection and other safety information.

Manufacturer’s instructions must be read and understood prior to use. Instructions

supplied with this product at time of shipment must be followed for proper use,

maintenance and inspection. Alteration or misuse of this product, or failure to

follow instructions could result in serious injury or death. Make only compatible

connections. See user manual.

30°

ALLO WA BLE LO ADING DIRE CTIONS

VERTICAL PLANE

60°

HORIZONTAL PLANE

WA RNIN G

THIS DOOR/WINDOW JAMB MUST BE INSTALLED AT THE BOTTOM OF THE WINDOW OR DOOR

OPENING, RESTING ON THE SILL. IF THE ANCHOR IS NOT RESTING ON THE SILL IT MAY ROTATE

WHEN LOADED, ALLOWING THE ANCHOR TO COME FREE OF THE WINDOW OR DOOR

OPENING. FAILURE TO FOLLOW THIS WARNING MAY RESULT IN SERIOUS INJURY OR DEAT H.

21.5 in. - 51.0 in

(54.6 cm - 129.5 cm)

OK

NO

INSPECTION LOG

DATE

INITIALS

OK

1

2

3

4

5

6

7

8

9

10

11

12

A

FORM NO: 5908299 REV: A

5

SAFETY INFORMATION

Please read, understand, and follow all safety information contained in these instructions prior to the use of this Anchorage Connector.

FAILURE TO DO SO COULD RESULT IN SERIOUS INJURY OR DEATH.

These instructions must be provided to the user of this equipment. Retain these instructions for future reference.

Intended Use:

This Anchorage Connector is intended for use as part of a complete personal fall protection system.

Use in any other application including, but not limited to, material handling, recreational or sports related activities, or other activities not described in

the User Instructions, is not approved by 3M and could result in serious injury or death.

This device is only to be used by trained users in workplace applications.

! WARNING

This Anchorage Connector is part of a personal fall protection system. It is expected that all users be fully trained in the safe installation and operation

of their personal fall protection system. Misuse of this device could result in serious injury or death. For proper selection, operation, installation,

maintenance, and service, refer to these User Instructions and all manufacturer recommendations, see your supervisor, or contact 3M Technical Service.

• To reduce the risks associated with working with an Anchorage Connector which, if not avoided, could result in serious injury or

death:

- Inspect the device before each use, at least annually, and after any fall event. Inspect in accordance with the User Instructions.

- If inspection reveals an unsafe or defective condition, remove the device from service and repair or replace according to the User Instructions.

- Any device that has been subject to fall arrest or impact force must be immediately removed from service and destroyed.

- The device must only be installed in the specied substrates or on structures detailed in the User Instructions. Installations and use outside the

scope of this instruction must be approved by 3M Fall Protection.

- The substrate or structure to which the anchorage connector is attached must be able to sustain the static loads specied for the anchor in the

orientations permitted in the User Instructions.

- Only connect other fall protection subsystems to the designated anchorage connection point on the device.

- Prior to drilling or fastening, ensure no electric lines, gas lines, or other critical embedded systems will be contacted by the drill or the device.

- Ensure that fall protection systems/subsystems assembled from components made by different manufacturers are compatible and meet the

requirements of applicable standards, including the ANSI Z359 or other applicable fall protection codes, standards, or requirements. Always

consult a Competent or Qualied Person before using these systems.

• To reduce the risks associated with working at height which, if not avoided, could result in serious injury or death:

- Ensure your health and physical condition allow you to safely withstand all of the forces associated with working at height. Consult with your

doctor if you have any questions regarding your ability to use this equipment.

- Never exceed allowable capacity of your fall protection equipment.

- Never exceed maximum free fall distance of your fall protection equipment.

- Do not use any fall protection equipment that fails pre-use or other scheduled inspections, or if you have concerns about the use or suitability

of the equipment for your application. Contact 3M Technical Services with any questions.

- Some subsystem and component combinations may interfere with the operation of this equipment. Only use compatible connections. Consult

3M prior to using this equipment in combination with components or subsystems other than those described in the User Instructions.

- Use extra precautions when working around moving machinery (e.g., top drive of oil rigs) electrical hazards, extreme temperatures, chemical

hazards, explosive or toxic gases, sharp edges, or below overhead materials that could fall onto you or your fall protection equipment.

- Use Arc Flash or Hot Works devices when working in high heat environments.

- Avoid surfaces and objects that can damage the user or equipment.

- Ensure there is adequate fall clearance when working at height.

- Never modify or alter your fall protection equipment. Only 3M or parties authorized, in writing, by 3M may make repairs to the equipment.

- Prior to use of fall protection equipment, ensure a rescue plan is in place which allows for prompt rescue if a fall incident occurs.

- If a fall incident occurs, immediately seek medical attention for the worker who has fallen.

- Do not use a body belt for fall arrest applications. Use only a Full Body Harness.

- Minimize swing falls by working as directly below the anchorage point as possible.

- If training with this device, a secondary fall protection system must be utilized in a manner that does not expose the trainee to an unintended

fall hazard.

- Always wear appropriate personal protective equipment when installing, using, or inspecting the device/system.

EN

6

;

Prior to installation and use of this equipment, record the product identication information from the ID label in the

Inspection and Maintenance Log (Table 2) at the back of this manual.

PRODUCT DESCRIPTION:

Figure 1 illustrates the 3M™ DBI-SALA™ Door Jamb Anchor. The Door Jamb Anchor is a single-point anchorage connector that

installs in a door or window opening.

Figure 2 illustrates components of the Door Jamb Anchor. See Table 1 for specications. The Door Jamb Anchor is comprised

of a Support Tube (A) with a Fixed Leg (B) and Adjustable Leg (C) that slides along the Support Tube to t the door or window

opening. The Adjustable Leg has pin holes and a Pin (D) for coarse adjustment. Once the Adjustable Leg is pinned in place,

a Knob with a Screw Foot (E) is tightened to secure the Door Jamb Anchor in the door/window opening. A D-Ring (F) on the

Support Tube serves as the connection point for a Lanyard or Self-Retracting Device (SRD).

Table 1 – Specications

System Specications:

Capacity: ANSI/CE: 1 Person with a combined weight (clothing, tools, etc.) of no more than 310 lbs (140 kg).

OSHA: 1 Person with a combined weight (clothing, tools, etc.) of no more than 420 lbs (190 kg)

Anchorage

Strength:

ANSI/

OSHA

Fall Arrest: The structure to which the Anchorage Connector is attached must sustain static

loads applied in the directions permitted by the Fall Arrest System of at least: 3,600 lbs (16

kN)with certication of a Qualied Person

2

; or 5,000 lbs (22 kN) without certication. When

more than one Personal Fall Arrest System (PFAS) is attached to an anchorage, these static

loads must be multiplied by the number of PFAS attached to the anchorage.

;

OSHA 1926.500 and OSHA 1910.66: Anchorages used for attachment to a Personal

Fall Arrest System (PFAS) must be independent of any anchorage used to suspend or

support platforms and must support 5,000 lbs (22 kN) per user attached, or be designed,

installed, and used as part of a completer PFAS which maintains a Safety Factor of a least 2

and is supervised by a Qualied Person

2

.

Restraint: The structure to which the Anchorage Connector is attached must sustain static

loads applied in the directions permitted by the Restraint System of at least 3,000 lbs (13

kN). When more than one Restraint System is attached to an anchorage, the static load must

be multiplied by the number of Restraint Systems attached to the anchorage.

CE

EN795

Anchorage Structure: The structure to which the Anchorage Connector is mounted must

be capable of sustaining force in the anticipated direction(s) of loading. Each Anchorage Point

location must be capable of sustaining 2,698 lbs (12 kN) loads.

Service Temperature: -40°C (-40° F)

Anchorage Connector

Breaking Strength

22 kN (5,000 lbs) Minimum Breaking Strength

Door/Window Jamb

Width:

See Figure 1: Minimum Width: 21.5 in. (54.6 cm), Maximum Width: 51.0 in. (129.5 cm)

Product Dimensions: See Figure 1

Product Weight: 14.0 lbs (6.3 kg)

Component Specications:

Figure 2

Reference Component Materials Notes

A Support Tube Aluminum

B

Fixed Leg Tube - Aluminum

Foot - Steel

Pad - Rubber

C Adjustable Leg Aluminum

D Coarse Adjustment Pin Steel

E

Fine Adjustment Knob Knob - Steel

Screw - Steel

Foot - Steel

Pad - Rubber

F D-Ring Alloy Steel Tensile Strength - 5,000 lbs (22.2 kN)

1

1 Qualied Person: An individual with a recognized degree or professional certicate, and extensive experience in Fall Protection. This individual must be capable

of design, analysis, evaluation, and specication in Fall Protection.

7

1.0 PRODUCT APPLICATION

1.1 PURPOSE: Anchorage Connectors are designed to provide anchorage connection points for Fall Arrest

1

or Fall Restraint

2

systems: Restraint, Work Positioning, Personnel Riding, Rescue, etc.

;

Fall Protection Only: This Anchorage Connector is for connection of Fall Protection Equipment. Do not connect

Lifting Equipment to this Anchorage Connector.

1.2 STANDARDS: Your Anchorage Connector conforms to the national or regional standard(s) identied on the front cover

of these instructions. If this product is resold outside the original country of destination, the re-seller must provide these

instructions in the language of the country in which the product will be used.

1.3 SUPERVISION: Installation of this equipment must be supervised by a Qualied Person

3

. Use of this equipment must be

supervised by a Competent Person

4

.

1.4 TRAINING: This equipment must be installed and used by persons trained in its correct application. This manual is to be

used as part of an employee training program as required by CE. It is the responsibility of the users and installers of this

equipment to ensure they are familiar with these instructions, trained in the correct care and use of this equipment, and

are aware of the operating characteristics, application limitations, and consequences of improper use of this equipment.

1.5 RESCUE PLAN: When using this equipment and connecting subsystem(s), the employer must have a rescue plan and

the means at hand to implement and communicate that plan to users, authorized persons

5

, and rescuers

6

. A trained, on-

site rescue team is recommended. Team members should be provided with the equipment and techniques to perform a

successful rescue. Training should be provided on a periodic basis to ensure rescuer prociency.

1.6 INSPECTION FREQUENCY:

The Anchorage Connector shall be inspected by the user before each use and, additionally,

by a competent person other than the user at intervals of no longer than one year.

7

Inspection procedures are described in

the “Inspection and Maintenance Log”. Results of each Competent Person inspection should be recorded on copies of the

“Inspection and Maintenance Log”.

1.7 AFTER A FALL: If the Anchorage Connector is subjected to the forces of arresting a fall, it must be removed from service

immediately and destroyed.

2.0 SYSTEM REQUIREMENTS

2.1 ANCHORAGE: Anchorage requirements vary with the fall protection application. Structure on which the

Anchorage Connector is placed or mounted must meet the Anchorage specications dened in Table 1.

2.2 PERSONAL FALL ARREST SYSTEM: Figure 1 illustrates the application of this Anchorage Connector. Personal Fall Arrest

Systems (PFAS) used with the system must meet applicable Fall Protection standards, codes, and requirements. Refer to

the instructions included with your Lanyard or Self-Retracting Device for Free Fall limitations. The PFAS must incorporate a

Full Body Harness and limit Maximum Arresting Force (MAF) to the following values:

ANSI/OSHA CE

PFAS with Shock Absorbing Lanyard 900 lb (4 kN) 1,350 lbs (6 kN)

PFAS with Self Retracting Device 900 lb (4 kN) 1,350 lbs (6 kN)

2.3 FALL PATH AND SRD LOCKING SPEED: A clear path is required to assure positive locking of an SRD. Situations which

do not allow for an unobstructed fall path should be avoided. Working in confined or cramped spaces may not allow the

body to reach sufficient speed to cause the SRD to lock if a fall occurs. Working on slowly shifting material, such as sand

or grain, may not allow enough speed buildup to cause the SRD to lock.

2.4 HAZARDS: Use of this equipment in areas with environmental hazards may require additional precautions to prevent

injury to the user or damage to the equipment. Hazards may include, but are not limited to: heat, chemicals, corrosive

environments, high voltage power lines, explosive or toxic gases, moving machinery, sharp edges, or overhead materials

that may fall and contact the user or Personal Fall Arrest System.

2.5 FALL CLEARANCE: Figure 3 illustrates the components of a Fall Arrest. There must be sufcient Fall Clearance (FC)

to arrest a fall before the user strikes the ground or other obstruction. Clearance is affected by a number of factors

including: Anchorage Location, (A) Lanyard Length, (B) Lanyard Deceleration Distance or SRD Maximum Arrest Distance,

(C) Harness Stretch and D-Ring/Connector Length and Settling (typically a Safety Factor of 1 m). Refer to the instructions

included with your Fall Arrest subsystem for specics regarding Fall Clearance calculation.

2.6 SWING FALLS: Swing Falls occur when the anchorage point is not directly above the point where a fall occurs (see Figure

4). The force of striking an object in a swing fall may cause serious injury or death. Minimize swing falls by working as directly

below the anchorage point as possible. Do not permit a swing fall if injury could occur. Swing falls will signicantly increase the

clearance required when a Self-Retracting Device or other variable length connecting subsystem is used.

1 Fall Arrest System: A collection of Fall Protection Equipment congured to arrest a free fall.

2 Fall Restraint System: A collection of Fall Protection Equipment congured to prevent the person’s center of gravity from reaching a fall hazard.

3 Qualied Person: An individual with a recognized degree or professional certicate, and extensive experience in Fall Protection. This individual must be capable

of design, analysis, evaluation, and specication in Fall Protection.

4 Competent Person: One who is capable of identifying existing and predictable hazards in the surroundings or working conditions which are unsanitary,

hazardous, or dangerous to employees, and who has authorization to take prompt corrective measures to eliminate them.

5 Authorized Person: For purposes of the Z359 standards, a person assigned by the employer to perform duties at a location where the person will be exposed

to a fall hazard.

6 Rescuer: Person or persons other than the rescue subject acting to perform an assisted rescue by operation of a rescue system.

7 Inspection Frequency: Extreme working conditions (harsh environments, prolonged use, etc.) may require increasing the frequency of competent person

inspections.

8

2.7 COMPONENT COMPATIBILITY: 3M equipment is designed for use with 3M approved components and subsystems

only. Substitutions or replacements made with non-approved components or subsystems may jeopardize compatibility of

equipment and may affect the safety and reliability of the complete system.

2.8 CONNECTOR COMPATIBILITY: Connectors are considered to be compatible with connecting elements when they

have been designed to work together in such a way that their sizes and shapes do not cause their gate mechanisms to

inadvertently open regardless of how they become oriented. Contact 3M if you have any questions about compatibility.

Connectors (hooks, carabiners, and D-rings) must be capable of supporting at least 5,000 lbs. (22.2 kN). Connectors

must be compatible with the anchorage or other system components. Do not use equipment that is not compatible.

Non-compatible connectors may unintentionally disengage (see Figure 5). Connectors must be compatible in size, shape,

and strength. If the connecting element to which a snap hook or carabiner attaches is undersized or irregular in shape, a

situation could occur where the connecting element applies a force to the gate of the snap hook or carabiner (A). This force

may cause the gate to open (B), allowing the snap hook or carabiner to disengage from the connecting point (C).

Self-locking snap hooks and carabiners are required by ANSI Z359 and OSHA.

2.9 MAKING CONNECTIONS: Snap hooks and carabiners used with this equipment must be self-locking. Ensure all

connections are compatible in size, shape and strength. Do not use equipment that is not compatible. Ensure all

connectors are fully closed and locked.

3M connectors (snap hooks and carabiners) are designed to be used only as specied in each product’s user’s instructions.

See Figure 6 for examples of inappropriate connections. Do not connect snap hooks and carabiners:

A. To a D-ring to which another connector is attached.

B. In a manner that would result in a load on the gate. Large throat snap hooks should not be connected to standard

size D-rings or similar objects which will result in a load on the gate if the hook or D-ring twists or rotates, unless the

snap hook complies is equipped with a 3,600 lb (16 kN) gate. Check the marking on your snap hook to verify that it

is appropriate for your application.

C. In a false engagement, where features that protrude from the snap hook or carabiner catch on the anchor, and

without visual conrmation seems to be fully engaged to the anchor point.

D. To each other.

E. Directly to webbing or rope lanyard or tie-back (unless the manufacturer’s instructions for both the lanyard and

connector specically allows such a connection).

F. To any object which is shaped or dimensioned such that the snap hook or carabiner will not close and lock, or that

roll-out could occur.

G. In a manner that does not allow the connector to align properly while under load.

9

3.0 INSTALLATION

;

For a certied anchor point, the structure to which the Anchorage Connector is attached must be designed or

evaluated by a Qualied Person

1

. A non-certied anchor point may be approved by a Competent Person

2

(see Table 1).

1

2

3.1 PLANNING: Plan the fall protection system prior to installation of the Door Jamb Anchor. Account for all factors that

may affect user safety before, during and after a fall. Consider all requirements, limitations and specications dened in

Section 2 and Table 1.

3.2 INSTALLING THE Door JAmb ANcHor: The Door Jamb Anchor can be installed in any door or window jamb of the

allowable Minimum Width and Maximum Widths meeting the specied Anchorage requirements (see Table 1). Figure 7

illustrates installtion of the Door Jamb Anchor. To install the Door Jamb Anchor:

1. Adjust the Door Jamb Anchor to t inside the desired opening by removing the coarse adjustment pin and sliding the

adjustable leg toward the D-ring. Rotate the ne adjustment knob counterclockwise until the foot is tight against the

support tube.

2. Place the Door Jamb Anchor in the door or window opening with the D-ring facing the area where work will be

performed. The adjustable leg may be located either on the left or right side of the opening. The Door Jamb Anchor

must rest on the bottom of the window or door opening. Do not attempt to install the Door Jamb Anchor in a position

where it is not supported by the oor or window sill.

3. Slide the adjustable leg as close to the door or window jamb as possible and insert the course adjustment pin in

the closest set of adjustment holes. Secure the anchor snuggly in the doorway or window by tightening the ne

adjustment Knob. The Door Jamb Anchor must be solid and secure after installation.

4.0 USE

4.1 bEForE EAcH USE: Verify that your work area and Personal Fall Arrest System (PFAS) meet all criteria dened in

Section 2 and a formal Rescue Plan is in place. Inspect the Door Jamb Anchor per the ‘User’ inspection points dened on

the “Inspection and Maintenance Log” (Table 2). If inspection reveals an unsafe or defective condition, do not use the

system. Remove the system from service and destroy, or contact 3M regarding replacement or repair.

4.2 FALL ArrEST coNNEcTIoNS: The Door Jamb Anchor is used with a Full Body Harness and Energy Absorbing Lanyard

or Self-Retracting Device (SRD). Figure 8 illustrates connection of the Lanyard (A) or SRD (B) between the Harness and

Door Jamb Anchor. Connect the Lanyard or SRD between the D-Ring on the Door Jamb Anchor and the back Dorsal

D-Ring on the Harness as instructed in the instructions included with the Lanyard or SRD.

;

Safe Work Area: Figure 8 illustrates the Safe Work Area for the Door Jamb Anchor. Never work at a horizontal

angle greater than 30° from perpendicular to the face of the Door Jamb Anchor to avoid improper loading of the

Anchorage Connection Point (see Figure 2). Never work at a position above or below the Anchorage Connection Points

that exceeds the vertical load requirements illustrated in Figure 2.

5.0 INSPECTION

5.1 INSPEcTIoN FrEQUENcY: The Door Jamb Anchor must be inspected at the intervals dened in Section 1. Inspection

procedures are described in the “Inspection and Maintenance Log” (Table 2). Inspect all other components of the Fall

Protection System per the frequencies and procedures dened in the manufacturer’s instructions.

;

RFID Tag: Door Jamb Anchors are equipped with a Radio Frequency Identication (RFID) Tag. The RFID Tag can

be used in conjunction with a Handheld Reading Device to simplify inspection and inventory control and provide records

for your fall protection equipment.

5.2 DEFEcTS: If inspection reveals an unsafe or defective condition, remove the Door Jamb Anchor from service immediately

and contact 3M regarding replacement or repair. Do not attempt to repair the Fall Arrest System.

;

Authorized Repairs Only: Only 3M or parties authorized in writing may make repairs to this equipment.

5.3 ProDUcT LIFE: The functional life of the Fall Arrest System is determined by work conditions and maintenance. As long

as the product passes inspection criteria, it may remain in service.

6.0 MAINTENANCE, SERVICING, STORAGE

6.1 cLEANING: Periodically clean the Door Jamb Anchor metal components with a soft brush, warm water, and a mild soap

solution. Ensure parts are thoroughly rinsed with clean water.

6.2 SErVIcE: Only 3M or parties authorized in writing by 3M may make repairs to this equipment. If the Door Jamb Anchor

has been subject to fall force or inspection reveals an unsafe or defective conditions, remove the system from service and

contact 3M regarding replacement or repair.

6.3 STorAGE AND TrANSPorT: When not in use, store and transport the Door Jamb Anchor and associated fall

protection equipment in a cool, dry, clean environment out of direct sunlight. Avoid areas where chemical vapors may

exist. Thoroughly inspect components after extended storage.

1 Qualied Person: An individual with a recognized degree or professional certicate, and extensive experience in Fall Protection. This individual must be capable

of design, analysis, evaluation, and specication in Fall Protection.

2 Competent Person: One who is capable of identifying existing and predictable hazards in the surroundings or working conditions which are unsanitary, hazard-

ous, or dangerous to employees, and who has authorization to take prompt corrective measures to eliminate them.

10

7.0 LABELS

Figure 9 Illustrates labels on the Door Jamb Anchor. Labels must be replaced if they are not fully legible. Information provided

on each label is as follows:

Read all instructions.

1

SPECIFICATIONS: Capacity: 1 Person, ANSI 310 lbs (140 kg) max, OSHA 420 lbs (190 kg) max.

Maximum arresting force 1,800 lbs

Materials: Aluminum anchor; Zinc plated alloy steel D-ring

Standards: Meets ANSI Z359.18 Type A and OSHA 1926.502 & 1910.140

Minimum Breaking Strength: 5,000 lbs (22kN) MBS

ANSI Minimum Service Temp. -40F (-40C)

2

USE: See User Manual for details on making connections. Do not allow lifeline to abrade against sharp edges during

use. Use caution when using this equipment near hazardous thermal, electrical, or chemical sources. Refer to User

Manual for additional information.

3

INSPECTION: Inspect anchor before each use. At least monthly, anchor should be inspected by a competent person in

accordance with the User Manual. Do not use if inspection reveals an unsafe or defective condition. Not user repairable.

This product is RFID enabled and contains an electronic tag that can be read by compatible readers - providing

inspection and other safety information.

4

ALLOWABLE LOADING DIRECTIONS: Never work at a horizontal angle greater than 30° from perpendicular to the face

of the Door Jamb Anchor to avoid improper loading of the Anchorage Connection Point. Never work at a position above

or below the Anchorage Connection Points that exceeds the vertical load requirements.

5

This door/window jamb must be installed at the bottom of the window or door Opening, resting on the sill. If the anchor

is not resting on the sill it may rotate. When loaded, allowing the anchor to come free of the window or door opening.

Failure to follow this warning may result in serious injury or death.

6 CE Standard and Notied Body ID

7 Year/Month Manufactured and Lot Number

8

Manufacturer’s instructions must be read and understood prior to use. Instructions supplied with this product at time of

shipment must be followed for proper use, maintenance and inspection. Alteration or misuse of this product, or failure

to follow instructions could result in serious injury or death. Make only compatible connections. See user manual.

9 Product Model Number

10

Manufacturer’s Location

11

One Person Maximum

12

Usage Temperature Range: -40°C to 60°C

13

Inspection Log: Date, Initials

Table 2 – Inspection and Maintenance Log

Inspection Date: Inspected By:

Components: Inspection: (See Section 1 for Inspection Frequency) User

Competent

Person

1

Door Jamb Anchor

(Figure 2)

Inspect the Door Jamb Anchor for damage: Look for cracks, dents, or deformities. Look for

bending or wear on the support tube, D-ring, and adjustment mechanisms. Ensure no parts are

loose or missing.

Inspect the adjustment mechanisms. The coarse adjustment pin must lock when inserted

through any of the adjustment holes.

Inspect entire unit for excessive corrosion. Inspect the torque on the ne adjustment screw and

tighten if necessary.

Labels (Figure 10)

Verify that all labels are securely attached and are legible (see ‘Labels’)

Anchor Structure

Inspect the door frame, window, and/or structure to make sure it is all load bearing and meets

the strength requirements from Table 1.

PFAS and Other

Equipment

Additional Personal Fall Arrest System (PFAS) equipment (harness, SRL, etc) being used with

the Flexiguard Anchorage System should be installed and inspected per the manufacturer’s

instructions.

Serial Number(s): Date Purchased:

Model Number: Date of First Use: