Yamaha CD Recordable/Rewritable Drive CRW2200 Användarmanual

Kategori
Optiska skivenheter
Typ
Användarmanual
(DECLARATION OF CONFORMITY PROCEDURE)
Responsible Party: Yamaha Electronics Corporation, USA
Address: 6660 Orangethorpe Avenue
Buena Park, CA 90620
Telephone: 714-522-9105
Fax: 714-670-0108
Type of Equipment: CD Recordable/Rewritable Drive
Model Name: CRW2200
CRW2200NB
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following conditions:
1) this device may not cause harmful interference, and
2) this device must accept any interference received including interference that
may cause undesired operation.
See user manual instructions if interference to radio reception is suspected.
FCC INFORMATION (U.S.A.)
1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!
This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements.
Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product.
2. IMPORTANT: When connecting this product to accessories and/or another product use only high quality shielded cables.
Cable/s supplied with this product MUST be used. Follow all installation instructions. Failure to follow instructions could void
your FCC authorization to use this product in the USA.
3. NOTE: This product has been tested and found to comply with the requirements listed in FCC Regulations, Part 15 for Class
“B” digital devices. Compliance with these requirements provides a reasonable level of assurance that your use of this product
in a residential environment will not result in harmful interference with other electronic devices. This equipment generates/uses
radio frequencies and, if not installed and used according to the instructions found in the users manual, may cause
interference harmful to the operation of other electronic devices. Compliance with FCC regulations does not guarantee that
interference will not occur in all installations. If this product is found to be the source of interference, which can be determined
by turning the product “OFF” and “ON”, please try to eliminate the problem by using one of the following measures:
Relocate either this product or the device that is being affected by the interference.
Utilize power outlets that are on different branch (circuit breaker or fuse) circuits or install AC line filter/s.
In the case of radio or TV interference, relocate/reorient the antenna. If the antenna lead-in is 300 ohm ribbon lead, change
the lead-in to coaxial type cable.
If these corrective measures do not produce satisfactory results, please contact the local retailer authorized to distribute this
type of product. If you can not locate the appropriate retailer, please contact Yamaha Electronics Corporation, USA,
6660 Orangethorpe Avenue, Buena Park, CA 90620 U.S.A.
CAUTION
Use of controls or adjustments or performance of
procedures other than those specified herein may result
in hazardous radiation exposure.
Laser Product Class: Class 1
Laser Diode Properties
Wavelength: 780-787 nm
Pulse Durations and Max. Output
at the lens of the Laser Pickup Unit
Read Mode: 0.7mW (Continuous)
Write Mode: Max. 38mW
(for 166ns, Min. Cycle 86.6ns)
ACHTUNG
Halten Sie sich beim Bedienen und Einstellen der
Bedienungselemente sowie bei der Bedienungsabfolge
an die Anleitung, da sonst gefährliche Strahlen austreten
können.
ATTENTION
L’emploi de commandes, de réglages ou un choix de
procédures différents des spécifications de cette
brochure peut entraîner une exposition à d’éventuelles
radiations pouvant être dangereuses.
PRECAUCION
El usar los controles o ajustar o realizar procedimientos
diferentes a los especificados aquí resultará en
peligrosas exposiciones a la radiación.
VARO! AVATTAESSA JA SUOJALUKITUS OHITETTAESSA
OLET ALTTINA NÄKYMÄTTÖMÄLLE
LASERSÄTEILYLLE. ÄLÄ KATSO SÄTEESEEN.
VARNING! OSYNLIG LASERSTRÅLNING NÄR DENNA DEL ÄR
ÖPPNAD OCH SPÄRREN ÄR URKOPPLAD.
BETRAKTA EJ STRÅLEN. STRÅLEN ÄR FARLIG.
Laserprodukt-Klasse: Klasse 1
Eigenschaften der Laserdiode
Wellenlänge: 780-787 nm
Impulsdauer und max. Ausgang an der Linse der
Laser-Abtasteinheit
Lesemodus: 0,7mW (kontinuierlich)
Schreibmodus: Max. 38mW
(für 166ns, Zyklusmin. 86,6ns)
Classe du produit laser: Classe 1
Caractéristiques de la diode laser
Longueur d’onde: 780-787 nm
Durée des impulsions et sortie maximum depuis
la lentille du bloc capteur optique
Mode de lecture: 0,7mW (continue)
Mode de gravure: max. 38mW
(pour 166ns, cycle min. 86,6ns)
Clase de producto láser: Clase 1
Propiedades del diodo láser
Longitud de onda: 780-787 nm
Duración del pulso y potencia de salida máxima
en el objetivo de la unidad captora láser
Modo de lectura: 0,7mW (continua)
Modo de escritura: máx. 38mW
(para 166ns, ciclo mínimo 86,6ns)
CLASS 1 LASER PRODUCT
LASER KLASSE 1 PRODUKT
LUOKAN 1 LASERLAITE
KLASS 1 LASER APPARAT
PRODUIT LASER DE CLASSE 1
DANGER - VISIBLE AND / OR INVISIBLE LASER
RADIATION WHEN OPEN. AVOID DIRECT EXPOSURE
TO BEAM.
CAUTION - VISIBLE AND / OR INVISIBLE LASER RADIATION WHEN OPEN.
AVOID EXPOSURE TO BEAM.
VARNING - SYNLIG OCH / ELLER OSYNLIG LASERSTRÅLNING NÄR DENNA
DEL ÄR ÖPPNAD. STRÅLEN ÄR FARLIG.
VARO ! AVATTAESSA OLET ALTTIINA NÄKYVÄLLE JA / TAI
NÄKYMÄTÖMÄLLE LASERSÄTEILYLLE. ÄLÄ KATSO SÄTEESEEN.
VARNING - SYNLIG OCH / ELLER OSYNLIG LASERSTRÅLNING NÄR DENNA DEL
ÄR ÖPPNAD. BETRAKTA EJ STRÅLEN.
VORSICHT ! SICHTBARE UND / ODER UNSICHTBARE LASERSTRAHLUNG
WENN ABDECKUNG GEÖFFNET. NICHT DEM STRAHL AUSSETZEN.
ATTENTION - RADIATION VISIBLE ET / OU INVISIBLE LORSQUE L’APPAREIL
EST OUVERT. EVITEZ TOUTE EXPOSITION AU FAISCEAU.
COMPLIES WITH 21 CFR CHAPTER1, SUBCHAPTER J.
i
OWNER’S MANUAL
English
ii
PLEASE READ CAREFULLY BEFORE PROCEEDING
PLEASE READ CAREFULLY BEFORE PROCEEDINGPLEASE READ CAREFULLY BEFORE PROCEEDING
PLEASE READ CAREFULLY BEFORE PROCEEDING
These precautions explain how to use the device correctly and safely, thereby preventing injury to
yourself or to others. This section has been sub-divided into a WARNING section and a CAUTION
section, according to the likelihood and nature of any potential injuries or damage inflicted. They relate
to your personal safety, and also help you minimize the risk of damaging the device. Please read these
sections carefully before proceeding.
WARNING
Always follow the basic precautions listed below to avoid the possibility of serious injury or even
death from electrical shock, short-circuiting, damages, fire, or other hazards. These precautions
include, but are not limited to, the following:
Do not open the device or attempt to disassemble or modify it.
Otherwise, there is an increased risk of electrical shock or fire. The device contains no user-
serviceable parts. If it appears to be malfunctioning, have it inspected by qualified service personnel.
Do not look inside the device.
If you expose your eyes to the laser inside the device, you risk damage to or loss of your vision.
Do not insert fingers or foreign objects into the device.
Otherwise, there is an increased risk of personal injury, electrical shock, damage to the device, or
fire. Please take particular care if small children are present.
Do not expose the device to rain or use it near water or in damp or wet conditions. Do not place
containers on it that contain liquids which might spill into any openings.
Otherwise, there is an increased risk of electrical shock, fire, or personal injury.
Follow the Owner’s Manual carefully.
Otherwise, there is an increased risk of personal injury, electrical shock, fire, or damage to the unit.
Follow the correct procedure when setting up the device.
If unusual smells, sounds, or smoke emanate from the device, or if liquids enter the device, switch
the computer off immediately and unplug it from the power outlet.
Otherwise, there is an increased risk of electrical shock, fire, or damage to the device. Return the
device immediately to the store where it was purchased, or alternatively, to the nearest Yamaha
dealer (listed at the back of this manual).
Make sure the computer is electrically grounded.
Otherwise, there is an increased risk of electrical shock.
When opening up the computer, always unplug the computer from the electrical outlet. Do not
touch the plug with wet hands.
Otherwise, there is an increased risk of electrical shock.
When used in a fan-cooled system, the drive should not be exposed to temperatures outside the
range 5 – 40°C (41 – 104°F).
SAFETY PRECAUTIONS
iii
CAUTION
Always follow the basic precautions listed below to avoid the possibility of physical injury to
yourself or others, or damage to the instrument or other property. These precautions include, but
are not limited to, the following:
Always unplug the computer from the electrical outlet if it will not be used for a prolonged period of
time, or if there is a risk of lightning.
Otherwise, there is an increased risk of electrical shock, short-circuiting, or fire.
Do not expose the device to excessive heat or vibrations, such as in areas subject to direct sunlight
or near a heater.
Also avoid placing it in extreme cold or in areas subject to excessive dust.
Otherwise, the front panel may become disfigured or the internal components may be damaged.
Do not use the device near other electrical products such as televisions, radios, or speakers.
Otherwise, this may cause interference which can affect the proper operation of those other
products.
Do not place the device in an unstable position.
Otherwise, it may accidentally fall down and be damaged or cause personal injury.
Mount the device horizontally.
Otherwise, written data may be destroyed. Set the device up according to the instructions in the
Owner’s Manual.
Always remove the disc from the tray before transporting the device.
Otherwise, written data may be destroyed.
When cleaning the device, never use benzene, paint thinners, detergents, or chemically coated
wiping cloths. Also, do not place vinyl, plastic, or rubber objects on the device.
Otherwise, the device may be damaged or its front panel may become discolored. Use a soft, dry
cloth to wipe the device.
Do not rest your weight on or place heavy objects on the device and do not use excessive force on
the buttons, switches or connectors.
Otherwise, there is an increased risk of damage to the device or personal injury.
Do not listen to audio with headphones at high volume or for prolonged periods of time.
Otherwise, there is an increased risk of hearing loss.
Before using the device, set the volume dial to its lowest setting.
Otherwise, sudden bursts of sound can cause hearing loss.
Do not place the device near sources of magnetic interference, such as computer displays.
Magnetic interference can affect the operation and stability of the device.
Have the device serviced regularly.
Otherwise, dust can build up inside the device, increasing the risk of fire or damage. For information
about service charges, contact the store where the device was purchased, or alternatively, the nearest
Yamaha dealer (listed at the back of this manual). The device should be serviced about once a year.
This drive is for use only with movable equipment, weighing less than 18 kg.
iv
About CD-R/RW discs
Please read the following regarding the handling of CD-R/RW discs.
1. Do not expose discs to excessive heat, such as in areas subject to direct sunlight or near
a heater.
Also, avoid keeping them in a humid place.
2. Do not touch the surface of a disc.
When handling a disc, hold it by its edges.
3. Remove dust and dirt from the surface of a disc.
Use air-based dust removers. The surface of a disc may be scratched if wiped with a dry cloth.
4. Do not stick labels on the surface of a disc.
5. Do not write on the surface of a disc except where indicated.
6. Do not clean discs with chemicals or detergents.
7. Do not bend or drop discs.
8. Do not use irregularly shaped discs, such as a star or a heart or a card shaped, etc.
Such discs could damage your new CD-R/RW drive. (Use only circular discs.)
Precautions for Transportation
Before transporting the device, always put it in its original box. If the device is transported
without adequate packing, the internal components may be damaged and cause the device
to malfunction.
Copyrights
When writing to CD-R/RW, make sure that you are not infringing any copyrights. It is illegal
to copy audio CDs for non-personal use. When backing up software, please make sure that
you are not infringing any software copyrights for that product.
WARRANTY
YAMAHA AND SUPPLIERS ACCEPT NO LIABILITY FOR THE LOSS OF ANY DATA OR
ANY PROBLEMS CAUSED AS A RESULT. AS A PRECAUTION, IT IS RECOMMENDED
THAT THE DISCS BE TESTED AFTER THEY HAVE BEEN WRITTEN TO.
FURTHERMORE, UNDER NO CIRCUMSTANCES DOES YAMAHA AND SUPPLIERS
GUARANTEE THE RELIABILITY OF THE DISCS.
1. The information contained in this manual is subject to change
without prior notice.
2. All trademarks contained in this manual belong to their respective
owners.
3. Yamaha does not bear any responsibility for any outcome as a result
of using this device.
4. Reproduction of this manual, either in part or in full, is expressly
forbidden.
The CRW2200E conforms to the power-saving mode of a computer to reduce power
consumption. (
P. 39)
v
Table of Contents
Introduction........................................................................ 1
Features of the CRW2200E Drive ...................................................... 1
Before Use ......................................................................... 3
System Requirements.......................................................................... 3
Supported Discs................................................................................... 4
Serial Number ..................................................................................... 6
Front and Rear of Unit............................................................ 7
Front Panel .......................................................................................... 7
Rear Panel ........................................................................................... 8
Setup Procedures ................................................................. 9
Tools.................................................................................................... 9
Setup Flowchart................................................................................. 10
Connecting the CRW2200E Drive.................................................... 11
Operation..........................................................................28
Loading a Disc .................................................................................. 28
Ejecting a Disc .................................................................................. 28
Ejecting a Disc in an Emergency ...................................................... 29
Troubleshooting..................................................................30
Appendix...........................................................................34
Writing Modes................................................................................... 34
About the firmware ........................................................................... 36
LED Indicator Messages................................................................... 37
CRW2200E Specifications................................................................ 37
Index.................................................................................................. 40
©2001 YAMAHA CORPORATION. All Rights Reserved.
This document may not, in whole or in part, be copied, photocopied, reproduced,
translated, transmitted, or reduced to any electronic medium of machine readable
form without prior consent in writing from Yamaha.
Windows is a registered trademark of Microsoft Corporation.
SafeBurn™ is a trademark of Yamaha Corporation.
All other trademarks are the property of their respective companies.
1
Introduction
High speed writing/reading
The CRW2200E drive supports up to 20X-speed writing of CD-R discs,
*1
and up to
10X-speed writing/rewriting of CD-RW discs.
*2
Furthermore, the drive supports data
reading and digital audio data extraction at up to 40X speed.
SafeBurn™ (Enhanced write stability technology)
Generous 8MB of buffer memory
Because of the large data storage area, stable disc writing is possible even at fast
speeds.
Buffer Underrun Protection
When data transfer from the host PC is interrupted, Buffer Underrun Protection is
activated to keep precious CD-R discs from going to waste. (
P. 2)
Optimum Write Speed Control
Before writing to CD-R, the CRW2200E drive checks the disc’s capability and
automatically selects the optimum writing speed for greater reliability.
Reliable writing
Yamaha’s proprietary Pure-Phase Laser System (patent applied for)
This technology reduces phase interference of the laser beam, so that it projects
accurately onto the disc. Jitter value an important measure of recording quality,
has been improved 25% compared with Yamaha models not using this
technology.
Running OPC (Optimum Power Control)
Running OPC automatically adjusts the output of the laser according to the
characteristics of the disc being used. Running OPC provides greatly enhanced
recording reliability for various manufacturer’s discs.
High-fidelity digital audio
The CRW2200E drive supports extraction of digital audio data at up to 40X speed,
as well as the recording of digital sound with complete fidelity even when writing at
20X speed. Also, the built-in digital audio output is ideal for the pure transmission of
an audio signal when connected to the SPDIF (digital audio) input of the computer's
sound card.
CD TEXT support
Information such as the song name or artist name can be recorded on Audio CDs
using CD creation software. The text data on the created disc can be displayed on a
CD player that is compatible with the CD TEXT format.
Features of the
CRW2200E
Drive
Introduction
2
*1 16X- or 20X-speed writing is enabled with the Partial CAV method. (
P. 5)
*2 10X-speed writing/rewriting is enabled with the CLV method, and the 4X-10X Full CAV method. (
P. 6)
Buffer Underrun Defined
CD-R/RW drives are equipped with buffer memory. This memory temporarily
stores data while a disc is being recorded. When buffer memory becomes empty
(due to unexpected interruptions or the system’s inability to keep up with the
writing process), a write error occurs. This error is known as a “buffer underrun
error.
A Buffer Underrun Error will permanently ruin the disc.
Yamaha Buffer Underrun Protection
Buffer Underrun Protection is featured in Yamaha’s CRW2200 series CD-R/
RW drives. When a buffer underrun is about to occur, a buffer underrun error is
prevented by temporarily suspending the writing process. Writing resumes when
enough data has accumulated again in buffer memory. Buffer Underrun
Protection on the CRW2200 series is extremely accurate, resulting in seamless
recording between stop and continuation points.
Yamaha Buffer Underrun Protection ensures error-free results.
➀➁
Data
If data transfer is
interrupted...
Data is stored in
buffer memory...
then buffer memory
begins to empty
When no data is left
in buffer memory...
(Buffer Underrun)
and then written
to disc
writing fails
(Buffer Underrun
Error)
➀➁
If data transfer is
interrupted...
Once data transfer
resumes normally...
and buffer memory is
about to empty...
enough data has accumulated in
buffer memory...
writing is suspended writing continues
3
Before Use
In order to use the CRW2200E drive, your computer system will need to meet the
following requirements.
Note
The
CRW2200E
drive may not write at the maximum speed depending on your computer’s
system configuration.
PC/AT-Compatible Computer
CPU: Pentium II-class or higher, 300MHz or faster.
RAM: 32MB memory (64MB or more recommended).
Note
If you are using Windows 2000 Professional operating system, you need 64MB memory or more.
A vacant 5.25-inch drive bay slot (For supplemental drive).
Operating System (OS)
Windows 95 (OSR2 or later), Windows 98, Windows 98 Second Edition, Windows
Me, Windows NT4.0 with Service Pack 3 or later, Windows 2000 Professional.
CD Writing Software
The CRW2200E drive requires CD writing software to write onto a CD-R/RW disc.
When you use the CD writing software, make sure that it supports the CRW2200E drive.
Note
For details about how to install and use the software, refer to the documentation that came with it.
Hard Drive Space
When writing to a CD-R/RW disc, you will need a working area (50 to 100MB free
space) on the hard drive. When creating an image file for all data to write to a CD-R/
RW disc, in addition to the working area, you will need as much hard drive space as
that data (up to 900MB in total). However, such hard drive space for the image file is
not needed when you are directly writing from a hard drive or CD-ROM drive, etc.
(on-the-fly writing).
About a disk image file
You can collect data files into a single disk image file for a CD-R/RW disc. Also, note that an
image file is useful when writing multiple discs with the same content. For further details, refer to
the documentation that came with your writing software.
System Requirements
Before Use
4
The CRW2200E drive can write to discs that carry the following logos:
*1 Compatible with Orange Book Part 2.
*2 Compatible with Orange Book Part 3 Vol. 1.
*3 Compatible with Orange Book Part 3 Vol. 2.
About the Orange Book
The Orange Book standard defines how all recordable discs (including CD-R and CD-RW) are
written. Part 2 of the Orange Book standard relates to CD-R discs, and Part 3 to CD-RW discs.
The standard was named after the color of the book’s pages.
Supported Discs
CD-R discs
*1
The
CRW2200E
drive can write to these discs at 1X, 2X, 4X, 8X, 12X, 16X,
or 20X speed. These discs can be played back in a CD-ROM drive or a CD
player.
Notes
16X- or 20X-speed writing is enabled with Partial CAV method. (
P. 5)
For 8X or faster writing, use CD-R discs that match their respective writing
speeds.
CD-RW discs
*2
There are two types of CD-RW discs: those that support write/rewrite speeds
of 1X, 2X, and 4X, and those that support only 2X. The
CRW2200E
drive
can write/rewrite at 2X or 4X speed on the first type of disc, and at 2X on the
second type of disc. These discs can be read/played on a device (e.g., CD-
ROM drive) that supports “CD-RW.”
High Speed CD-RW discs
*3
These discs allow writing/rewriting at 4X to 10X speeds. The
CRW2200E
drive can write/rewrite these discs at 4X, 8X, or 10X speed. These discs can be
read/played by a CD-RW drive that bears the High Speed CD-RW logo, or by
a device (e.g., CD-ROM drive) that supports “CD-RW.”
Note
10X-speed writing/rewriting is enabled with the CLV method, and the 4X-10X
Full CAV method. (
P. 6)
In order to write, erase, or read these discs using a CD-R/RW
drive, a drive bearing the High Speed CD-RW logo must be
used. When using a CD-ROM drive to read these discs, the
drive must be capable of reading CD-RW discs.
If these discs are used in a CD-R/RW drive not bearing the
High Speed CD-RW logo, the discs may not be recognized,
resulting in the computer not operating correctly or other
malfunctions occurring.
Refer to the page at the URL below before attempting to read
these discs on a Yamaha CD-R/RW drive not bearing the
High Speed CD-RW logo.
URL: http://www.yamaha.co.jp/english/product/computer/
Before Use
5
About CD-ROMs
A CD-ROM disc is a compact disc containing high-density read-only data. It
has many applications, including the playback of music and video, the archiving
of data, as well as on-line documentation. The following are descriptions of each
CD-ROM format:
CD-DA: Up to 79 minutes of stereo audio is written in 16-bit resolution at a
sampling rate of 44.1kHz for a 79 minute disc.
Data CD: Up to 700 megabytes of computer data is stored in standard ISO9660
format for a 700MB disc.
Video CD: These hold movies in which the video and audio data has been
compressed using MPEG-1 technology.
About Partial CAV (Constant Angular Velocity)
Writing to a CD-R disc is normally done using the CLV (Constant Linear
Velocity) method. In this method, the disc rotation speed will be so adjusted as
to keep a constant data transfer rate at any portion of the disc. In other words,
the disc rotation speed will vary in CLV writing.
In contrast, the CAV (Constant Angular Velocity) method uses a constant disc
rotation speed for all portions of the disc so that the data transfer rate will vary.
Because the CAV method has the advantage of largely increasing the data
transfer rate with a minimum load to the drive’s mechanism (compared to CLV’s
rotation speed adjustment), many current CD-ROM drives use the CAV method.
CD formats define the constant linear density of written data (data should be
written onto the disc track in the constant pitch) so that the amount of recorded
data per disc rotation will increase as the writing point moves from the inner to
the outer. In other words, in CAV writing the outer portion has an increased data
transfer rate.
The CRW2200E drive uses the CAV method in the inner portions as well as the
CLV method in the outer portions (Partial CAV) in order to enable up to 20X-
speed writing. The drive will control the disc rotation speed to start writing at
12X speed in the inner portions, gradually accelerating up to 20X speed and
maintaining 20X speed in the outer portions.
Before Use
6
Once you have taken the CRW2200E drive out of its packaging, you should
immediately note down the serial number found at the top of the drive with the bar
code. You may need to refer to this number when requesting Customer Support
services. In the box below the following diagram, write down the 10-character serial
number (consisting of 3 letters followed by 7 digits).
About 10X-speed writing/rewriting of a High Speed CD-RW disc
10X-speed writing/rewriting of a High Speed CD-RW disc is enabled with the
CLV method, and the 4X-10X Full CAV method.
Commonly, writing/rewriting is enabled with the CLV method.
When writing/rewriting with packet writing, you can also select the Full CAV
method.
For more details, refer to the documentation that came with your writing
software. (Make sure that your writing software supports the Full CAV method.
The supplied writing software is supported.)
When you try to open and compile directly your file of the CD-RW disc with an
application, Yamaha recommends you using the Full CAV method.
Serial Number
Serial No.
Serial number
(3 letters and 7 digits
)
7
Front and Rear of Unit
The CRW2200E drive’s front panel features the following:
Disc tray
The tray is used to hold the disc. It slides out from the drive unit when a disc needs to be
loaded or unloaded. (
P. 28)
Manual Eject hole
Only use this if no other method is available for unloading a disc. (
P. 29)
Eject button
Press this button when you need to open or close the tray. Remove the disc after the tray
has opened. (
P. 28)
Headphone jack
You can connect stereo headphones to this stereo mini jack and listen to an audio CD
loaded in the drive.
Headphone volume control
Adjust this control to set a suitable volume level when listening to an audio CD using the
headphone jack. Slide the knob to the left to decrease the volume and to the right to
increase it.
LED
Indicates the operation status of the
CRW2200E
drive. (
P. 37)
Front Panel
Front and Rear of Unit
8
The CRW2200E drive’s rear panel features the following:
DIGITAL AUDIO OUT connector
If your sound card has a SPDIF (digital audio) input connector, you can connect the
DIGITAL AUDIO OUT connector of the unit to the SPDIF connector using a digital audio
cable (sold separately).(
P. 22)
ANALOG AUDIO OUT connector
Connect one end of the 4-pin audio cable to this and the other end to your computer’s
sound card or built-in audio. (
P. 21)
Jumper switch
Plug a plastic shunt into this jumper switch to select the connection, either IDE master or
slave. The
CRW2200E
drive’s factory setting is SLAVE. (
P. 17)
IDE INTERFACE CONNECTOR
Insert the connector of the IDE cable here. Make sure you align the red line of the ribbon cable
with pin 1 of the drive’s connector, marked “IDE INTERFACE CONNECTOR 1.” (
P. 20)
DC INPUT connector
Insert the power connector from your computer’s power supply in this socket to feed power
to the drive. (
P. 23)
Rear Panel
9
Setup Procedures
You will need the following tools at hand when installing the CRW2200E drive.
Phillips Screwdriver
You will need to use this when removing the cover of your computer and when
mounting the drive. You may also need to temporarily remove the sound card to gain
access to the CD audio connectors, in which case, a small screw retaining the sound
card’s face plate has to be removed.
Note
Make sure your screwdriver’s head is the correct size for the screws you need to remove.
Long-Nosed Pliers
You will need these to insert or remove the plastic shunts when setting the jumper
switches at the rear of the CRW2200E drive.
Tools
Setup Procedures
10
This flowchart shows the procedure for setting up the CRW2200E drive. For easy
cross-referencing, the relevant pages in this manual are also given.
Setup Flowchart
Connecting the
CRW2200E
Drive
1. Opening the Computer (
P. 11)
2. Choosing the Connecting Method (
P. 13)
3. Setting the Jumper Switches (
P. 17)
4. Installing the
CRW2200E
Drive (
P. 18)
STEP
1
Configuring the Operating System
(
P. 25)
Check that the
CRW2200E
drive is recognized
correctly.
STEP
2
Installing the CD Writing
Software
For details about how to install the software,
refer to the documentation that came with it.
STEP
3
Start Using the
CRW2200E
Drive!
Use the drive to create audio CDs, to back up
data on your hard disk, or for whatever purpose
suits your needs.
STEP
4
Setup Procedures
11
This section explains how to connect the CRW2200E drive to a tower-type computer.
Note
The way of removing the casing or panel, or installing built-in devices may differ from your
computer. Be sure to follow the procedures in the documentation that came with your computer.
Opening the Computer
1
11
1
Power down your computer and unplug it from the AC outlet.
If you proceed without doing this, you run
the risk of receiving an electric shock and/or
short-circuiting and damaging components,
including the CRW2200E drive.
2
22
2
Remove all attached cables and peripheral devices and the outer casing
of the computer. If you need to remove screws in the process, make sure
you don’t lose them. Remove the cover and front panel of the computer.
Note
The method for removing the casing and fitting the drive in the drive bay can vary depending
on the manufacturer. For further details, refer to the documentation that came with your
computer.
Connecting the
CRW2200E
Drive
Front panel
Cover
Setup Procedures
12
3
33
3 Touch a metal part of the computer’s chassis or power supply unit to
discharge any static charge that may have built up inside your body.
Alternatively, you can wear an anti-static grounding wrist strap.
You can permanently damage
equipment if you touch it while there is
any static charge in your body.
Discharge any static charge
1 / 1

Yamaha CD Recordable/Rewritable Drive CRW2200 Användarmanual

Kategori
Optiska skivenheter
Typ
Användarmanual