Stanley SFMCCS730B Användarmanual

varumärke: Stanley

Modell: SFMCCS730B

Kategori: Sladdlösa motorsågar

Typ: Användarmanual

Denna manual är också lämplig för

SFMCCS730M1

www.stanley.gb

6112 7

13 2 12 15

5 4

SFMCCS730

English (original instructions) 7

Deutsch (übersetzt von den originalanweisungen) 20

Français (traduction de la notice d’instructions originale) 34

Italiano (tradotto dalle istruzioni originali) 48

Nederlands (vertaald vanuit de originele instructies) 63

Español (traducido de las instrucciones originales) 77

Português (traduzido das instruções originais) 91

Svenska (översatt från de ursprungliga instruktionerna) 106

Norsk (oversatt fra de originale instruksjonene) 117

Dansk (oversat fra original brugsvejledning) 129

Suomi (käännetty alkuperäisestä käyttöohjeesta) 141

Ελληνικά (μετάφραση από τις πρωτότυπες οδηγίες) 153

18b

18a

14 14a

21 45

A B

C D

5 4

2119

E4 5

3mm

G H

10 9

11 4

60°

(0.635mm)

O P

Retreat

Tree

45º

Direction of fall

51mm

Direction of fall

Notch

Felling back cut

51mm

Hinge

U V

W X

Intended use

Your STANLEY FATMAX, SFMCCS730 Compact Chainsaw

has been designed for light duty cutting and pruning. This

appliance is intended for professional and private, non

professional users.

Safety instructions

General power tool safety warnings

Warning! Read all safety warnings,

instructions, illustrations and specications

provided with power tool. Failure to follow all

instructions listed below may result in electric

shock, re and/or serious injury.

Save all warnings and instructions for future reference.

The term "power tool" in all of the warnings listed below refers

to your mains operated (corded) power tool or battery oper-

ated (cordless) power tool.

1. Work area safety

a. Keep work area clean and well lit. Cluttered or dark

areas invite accidents.

b. Do not operate power tools in explosive atmospheres,

such as in the presence of ammable liquids, gases

or dust. Power tools create sparks which may ignite the

dust or fumes.

c. Keep children and bystanders away while operating a

power tool. Distractions can cause you to lose control.

2. Electrical safety

a. Power tool plugs must match the outlet. Never modify

the plug in any way. Do not use any adapter plugs

with earthed (grounded) power tools. Unmodied plugs

and matching outlets will reduce risk of electric shock.

b. Avoid body contact with earthed or grounded

surfaces such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric shock

if your body is earthed or grounded.

c. Do not expose power tools to rain or wet conditions.

Water entering a power tool will increase the risk of

electric shock.

d. Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool. Keep

cord away from heat, oil, sharp edges or moving

parts. Damaged or entangled cords increase the risk of

electric shock.

e. When operating a power tool outdoors, use an

extension cord suitable for outdoor use. Use of a cord

suitable for outdoor use reduces the risk of electric shock.

f. If operating a power tool in a damp location is

unavoidable, use a residual current device (RCD)

protected supply. Use of an RCD reduces the risk of

electric shock.

3. Personal safety

a. Stay alert, watch what you are doing and use common

sense when operating a power tool. Do not use a

power tool while you are tired or under the inuence

of drugs, alcohol or medication. A moment of inattention

while operating power tools may result in serious personal

injury.

b. Use personal protective equipment. Always wear eye

protection. Protective equipment such as a dust mask,

non-skid safety shoes, hard hat, or hearing protection

used for appropriate conditions will reduce personal

injuries.

c. Prevent unintentional starting.

ENGLISH (Original instructions)

Ensure the switch is in the off-position before

connecting to power source and/or battery pack,

picking up or carrying the tool. Carrying power tools

with your nger on the switch or energising power tools

that have the switch on invites accidents.

d. Remove any adjusting key or wrench before turning

the power tool on. A wrench or a key left attached to a

rotating part of the power tool may result in personal injury.

e. Do not overreach. Keep proper footing and balance at

all times. This enables better control of the power tool in

unexpected situations.

f. Dress properly. Do not wear loose clothing or

jewellery. Keep your hair, clothing and gloves away

from moving parts. Loose clothes, jewellery or long hair

can be caught in moving parts.

g. If devices are provided for the connection of dust

extraction and collection facilities, ensure these are

connected and properly used. Use of dust collection can

reduce dust-related hazards.

h. Do not let familiarity gained from frequent use of tools

allow you to become complacent and ignore tool

safety principles. A careless action can cause severe

injury within a fraction of a second.

4. Power tool use and care

a. Do not force the power tool. Use the correct power

tool for your application. The correct power tool will do

the job better and safer at the rate for which it was

designed.

b. Do not use the power tool if the switch does not turn it

on and off. Any power tool that cannot be controlled with

the switch is dangerous and must be repaired.

c. Disconnect the plug from the power source and/or the

battery pack from the power tool before making any

adjustments, changing accessories, or storing power

tools. Such preventive safety measures reduce the risk of

starting the power tool accidentally.

d. Store idle power tools out of the reach of children and

do not allow persons unfamiliar with the power tool or

these instructions to operate the power tool. Power

tools are dangerous in the hands of untrained users.

e. Maintain power tools. Check for misalignment or

binding of moving parts, breakage of parts and any

other condition that may affect the power tools

operation. If damaged, have the power tool repaired

before use. Many accidents are caused by poorly

maintained power tools.

f. Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges are less

likely to bind and are easier to control.

g. Use the power tool, accessories and tool bits etc. in

accordance with these instructions, taking into

account the working conditions and the work to be

performed. Use of the power tool for operations different

from those intended could result in a hazardous situation.

h. Keep handles and grasping surfaces dry, clean and

free from oil and grease. Slippery handles and

grasping surfaces do not allow for safe handling and

control of the tool in unexpected situations.

5. Battery tool use and care

a. Recharge only with the charger specied by the

manufacturer. A charger that is suitable for one type of

battery pack may create a risk of re when used with

another battery pack.

b. Use power tools only with specically designated

battery packs. Use of any other battery packs may create

a risk of injury and re.

c. When battery pack is not in use, keep it away from

other metal objects, like paper clips, coins, keys,

nails, screws, or other small metal objects, that can

make a connection from one terminal to another.

Shorting the battery terminals together may cause burns

or a re.

d. Under abusive conditions, liquid may be ejected from

the battery; avoid contact. If contact accidentally

occurs, ush with water. If liquid contacts eyes,

additionally seek medical help. Liquid ejected from the

battery may cause irritation or burns.

e. Do not use a battery pack or tool that is damaged or

modied. Damaged or modied batteries may exhibit

unpredictable behaviour resulting in re, explosion or risk

of injury.

f. Do not expose a battery pack or tool to re or

excessive temperature. Exposure to re or temperature

above 130 °C may cause explosion. NOTE: The

temperature „130 °C“ can be replaced by the temperature

„265 °F“.

g. Follow all charging instructions and do not charge the

battery pack or tool outside the temperature range

specied in the instructions. Charging improperly or at

temperatures outside the specied range may damage the

battery and increase the risk of re.

6. Service

a. Have your power tool serviced by a qualied repair

person using only identical replacement parts. This

will ensure that the safety of the power tool is maintained.

b. Never service damaged battery packs. Service of

battery packs should only be performed by the

manufacturer or authorized service providers (only used

for battery tools).

ENGLISH

(Original instructions)

General chain saw safety warnings

Warning! Additional safety warnings for

chainsaws

uKeep all parts of the body away from the saw chain

when the chainsaw is operating. Before you start the

chainsaw, make sure the saw chain is not contacting

anything. A moment of inattention while operating chain

saws may cause entanglement of your clothing or body

with the chain saw.

uAlways hold the chainsaw with your right hand on the

rear handle and your left hand on the front handle.

Holding the chainsaw with a reversed hand conguration

increases the risk of personal injury and should never be

done.

uHold the chain saw by insulated gripping surfaces

only, because the saw chain may contact hidden

wiring. Saw chains contacting a "live" wire may make

exposed metal parts of the chain saw "live'" and could give

the operator an electric shock.

uWear eye protection. Further protective equipment for

hearing, head, hands, legs and feet is recommended.

Adequate protective equipment will reduce personal injury

from ying debris or accidental contact with the saw chain.

uDo not operate a chain saw in a tree, on a ladder, from

a rooftop, or any unstable support. Operation of a chain

saw in this manner could result in serious personal injury.

uAlways keep proper footing and operate the chain saw

only when standing on xed, secure and level surface.

Slippery or unstable surfaces such as ladders may cause

a loss of balance or control of the chainsaw.

uWhen cutting a limb that is under tension be alert

for spring back. When the tension in the wood bres is

released the spring loaded limb may strike the operator

and/or throw the chain saw out of control.

uUse extreme caution when cutting brush and saplings.

The slender material may catch the saw chain and be

whipped toward you or pull you off balance.

uCarry the chain saw by the front handle with the chain

saw switched off and away from your body. When

transporting or storing the chainsaw always t the

guide bar cover. Proper handling of the chain saw will

reduce the likelihood of accidental contact with the moving

saw chain.

uFollow instructions for lubricating, chain tensioning

and changing accessories. Improperly tensioned or

lubricated chain may either break or increase the chance

for kickback

uCut wood only. Do not use chainsaw for purposes not

intended. For example: do not use the chainsaw for

cutting plastic, masonry or non-wood building materi-

als.

Use of the chainsaw for operations different than intended

could result in a hazardous situation.

uDo not attempt to fell a tree until you have an

understanding of the risks and how to avoid them.

Serious injury could occur to the operator or bystanders

while felling a tree.

uFollow all instructions when clearing jammed mate-

rial, storing or servicing the chain saw. Make sure the

switch is off and the battery pack is removed. Unex-

pected actuation of the chain saw while clearing jammed

material or servicing may result in serious personal injury.

Additional power tool safety warnings

Warning! Additional safety warnings for co

pact chainsaws.

The intended use is described in this instruction manual. Do

not use the tool for purposes not intended; for example do not

use the tool to fell trees. The use of any accessory or attach-

ment or performance of any operation with this tool other than

those recommended in this instruction manual may present a

risk of personal injury.

uWear close tting and protective clothing including

a safety helmet with visor/goggles, ear protectors,

non- skid safety footwear, protective bib trousers and

strong leather gloves.

uAlways position yourself out of the path of falling

branches.

uThe safe distance between a branch to be felled and

bystanders, buildings and other objects is at least

2 1/2 times the length of the branch. Any bystander,

building or object within this distance is at risk from being

struck by the falling branch.

uPre-plan a safe exit from falling branches. Ensure the

exit route is clear of obstacles that would prevent or hinder

movement. Remember wet grass and freshly cut bark is

slippery.

uEnsure someone is nearby (but at a safe distance) in

case of an accident.

uDo not use the tool while standing in a tree, on a lad-

der or on any other unstable surface.

uKeep proper footing and balance at all times.

uHold the tool rmly with both hands when the motor is

running.

uDo not let the moving chain contact any object at the

tip of the guide bar.

uStart cutting only with the chain moving at full speed.

uDo not attempt to enter a previous cut. Always make a

fresh cut.

uWatch for shifting branches or other forces that could

close a cut and pinch or fall into the chain.

uDo not attempt to cut a branch when the diameter of

the branch exceeds the cutting length of the tool.

ENGLISH (Original instructions)

uAlways remove the battery from the tool and place the

chain cover assembly over the chain when storing or

transporting the tool.

uKeep the saw chain sharp and properly tensioned.

Check the tension at regular intervals.

uSwitch the tool off, allow the chain to stop and remove

the battery from the tool before carrying out any

adjustment, servicing or maintenance.

uOnly use genuine replacement parts and accessories.

uKeep handles dry, clean, and free from oil and grease.

Greasy, oily handles are slippery causing loss of control.

uThe spiked bumper may become sharp during the life

of the product. Handle with care.

uWhen handling the product the chain bar may become

hot, handle with care.

Causes and operator prevention of kickback

Kickback may occur when the nose or tip of the guide bar

touches an object, or when the wood closes in and pinches

the saw chain in the cut.

Tip contact in some cases may cause a sudden reverse reac-

tion, kicking the guide bar up and back towards the operator.

Pinching the saw chain along the top of the guide bar may

push the guide bar rapidly back towards the operator.

Either of these reactions may cause you to lose control of

the chainsaw which could result in serious personal injury.

Do not rely exclusively upon the safety devices built into your

chainsaw. As a chainsaw user, you should take several steps

to keep your cutting jobs free from accident or injury.

Kickback is the result of tool misuse and / or incorrect operat-

ing procedures or conditions and can be avoided by taking

proper precautions as given below:

uMaintain a rm grip, with thumbs and ngers

encircling the chainsaw handles. With both hands on

the chainsaw, position your body and arm to allow

you to resist kickback forces. Kickback forces can be

controlled by the operator, if proper precautions are taken.

Do not let go of the chainsaw.

uDo not overreach and do not cut above shoulder

height. This helps prevent unintended tip contact and

enables better control of the chainsaw in unexpected situ-

ations.

uOnly use replacement guide bars and chains specied

by the manufacturer. Incorrect replacement guide bars

and chains may cause chain breakage and/ or kickback.

uFollow the manufacturer's sharpening and mainte-

nance instructions for the saw chain. Decreasing the

depth gauge height can lead to increased kickback.

Safety recommendations for the chainsaw

uWe strongly recommend that rst time users obtain practi-

cal instruction in the use of the chainsaw and protective

equipment from an experienced user.

Initial practice should be completed sawing logs on a saw

horse or cradle.

uWe recommend that when carrying the chainsaw that you

remove the battery and make sure that the saw chain is

facing backwards.

uMaintain your chainsaw when not in use. Do not store

your chainsaw for any length of time without rst remov-

ing the saw chain and guide bar which should be kept

immersed in oil. Store all parts of your chainsaw in a dry,

secure place out of reach of children.

uWe recommend you drain the oil reservoir prior to storage.

uBe sure of your footing and pre-plan a safe exit from a

falling tree or branches.

uUse wedges to help control felling and prevent binding the

guide bar and saw chain in the cut.

uSaw chain care. Keep the saw chain sharp and snug on

the guide bar. Ensure the saw chain and guide bar are

clean and well oiled. Keep handles dry, clean and free

from oil and grease.

Kickback can be caused by:

uStriking branches or other objects accidentally with a tip of

the saw while the saw chain is moving.

uStriking metal, cement or any other hard material near the

wood, or buried in the wood.

uA dull or loose chain.

uCutting above shoulder height.

uLack of attention when holding or guiding the chainsaw

while cutting.

uOver-reaching. Keep proper footing and balance at all

times and do not overreach.

uDo not try to insert into a previous cut. As this could cause

kickback. Make a fresh cut every time.

uWe strongly recommend you do not attempt to operate

your chainsaw while in a tree, on a ladder or on any other

unstable surface. If you decide to do so, be advised that

these positions are extremely dangerous.

uWhen cutting a branch that is under tension, be alert for

spring back so that you will not be struck when the tension

is released.

Avoid cutting:

uPrepared timber.

uInto the ground.

uInto wire fences, nails. etc.

uInto small sized brush and saplings because slender

material may catch the saw chain and be whipped towards

you, or pull you off balance.

uDo not use your chainsaw above shoulder height.

uEnsure someone is nearby (but at a safe distance) in case

of an accident.

uIf for any reason you have to touch the saw chain, make

sure your chainsaw is switched off and the battery is

removed.

uThe noise from this product can exceed 80 dB(A). We

therefore recommend you take appropriate measures for

the protection of hearing

Residual risks.

Additional residual risks may arise when using the tool which

may not be included in the enclosed safety warnings. These

risks can arise from misuse, prolonged use etc.

Even with the application of the relevant safety regulations

and the implementation of safety devices, certain residual

risks can not be avoided. These include:

uInjuries caused by touching any rotating/moving parts.

uInjuries caused when changing any parts, blades or ac-

cessories.

uInjuries caused by prolonged use of a tool. When using

any tool for prolonged periods ensure you take regular

breaks.

uImpairment of hearing.

uHealth hazards caused by breathing dust developed when

using your tool (example:- working with wood, especially

oak, beech and MDF.)

Noise and Vibration

The declared vibration emission values and the declared noise

emission value(s) stated in the technical data and the declara-

tion of conformity have been measured in accordance with a

standard test method provided by EN 62841 and may be used

for comparing one tool with another. The declared vibration

emission value and the declared noise emission value(s) may

also be used in a preliminary assessment of exposure.

Warning! The vibration and noise emission value during

actual use of the power tool can differ from the declared value

depending on the ways in which the tool is used. The vibration

level may increase above the level stated.

When assessing vibration exposure to determine safety

measures required by 2002/44/EC to protect persons regularly

using power tools in employment, an estimation of vibration

exposure should consider, the actual conditions of use and the

way the tool is used, including taking account of all parts of the

operating cycle such as the times when the tool is switched off

and when it is running idle in addition to the trigger time.

Labels on tool

The following pictograms are shown on the tool along with the

date code:

Warning! To reduce the risk of injury, the

user must read the instruction manual.

Do not use your saw in wet conditions or

expose it to rain.

Always wear head, hearing and eye protec-

tion.

Always wear a dust mask

Always wear gloves.

Always wear non-slip safety footwear.

Always hold a chainsaw rmly with both

hands.

Pay attention to the kickback of the chain-

saw and avoid contact with the tip of the

chain bar.

Do not use chainsaw one handed"

Switch the tool off. Before performing any

maintenance on the tool, remove the battery

from the tool.

Beware of falling objects. Keep bystanders

away

To ensure continued safe operation, check

the chain tension as described in this manu-

al after every 10 minutes of use, and adjust

back to a clearance of 3 mm as required. Oil

the chain after every 10 minutes of use.

Warning! Do not touch chain at the chipping

ejection point

Direction of rotation of the chain.

To ensure continued safe operation, the

chain and guide bar must only be replaced

with original STANLEY FATMAX. Replace-

ment chain part number A6158 replacement

guide bar part number 90619609.

Directive 2000/14/EC guaranteed

sound power.

ENGLISH (Original instructions)

Additional safety instructions for batteries and

chargers

Batteries

uNever attempt to open for any reason.

uDo not expose the battery to water.

uDo not expose the battery to heat.

uDo not store in locations where the temperature may

exceed 40°C.

uCharge only at ambient temperatures between 10°C and

40°C.

uCharge only using the charger provided with the appli-

ance/tool. Using the wrong charger could result in an

electric shock or overheating of the battery.

uWhen disposing of batteries, follow the instructions given

in the section “Protecting the environment”.

uDo not damage/deform the battery pack either by puncture

or impact, as this may create a risk of injury and re.

uDo not charge damaged batteries.

Under extreme conditions, battery leakage may occur.

When you notice liquid on the batteries, carefully wipe the

liquid off using a cloth. Avoid skin contact.

In case of skin or eye contact, follow the instructions below.

Warning! The battery uid may cause personal

injury or damage to property. In case of skin contact,

immediately rinse with water. If redness, pain or ir-

ritation occurs seek medical attention. In case of eye

contact, rinse immediately with clean water and seek

medical attention.

Chargers

Warning! Your charger has been designed for a specic

voltage. Always check that the mains voltage corresponds to

the voltage on the rating plate.

Warning! Never attempt to replace the charger unit with a

regular mains plug.

uUse your STANLEY FATMAX charger only to charge the

battery in the appliance/tool with which it was supplied.

Other batteries could burst, causing personal injury and

damage.

uNever attempt to charge non-rechargeable batteries.

uIf the supply cord is damaged, it must be replaced by the

manufacturer or an authorised STANLEY FATMAXService

Centre in order to avoid a hazard.

uDo not expose the charger to water.

uDo not open the charger.

uDo not probe the charger.

uThe charger must be placed in a well ventilated area when

charging.

Labels on the charger

The following symbols are found on your charger:

The charger is intended for indoor use only.

Read the instruction manual before use.

Electrical safety

Your charger is double insulated; therefore no

earth wire is required. Always check that the

mains voltage corresponds to the voltage on the

rating plate. Never attempt to replace the charger

unit with a regular mains plug.

uIf the supply cord is damaged, it must be replaced by

the manufacturer or an authorised STANLEY FATMAX

Service Centre in order to avoid a hazard.

Features

1. ON/OFF trigger switch

2. Lock-off lever

3. Chain brake / front hand guard

4. Guide bar

5. Saw chain

6. Sprocket cover

7. Bar lock nut

8. Chain tensioning screw

9. Oil cap

10. Oil level indicator

11. Guide bar scabbard

12. Rear handle

13. Front handle

14. Battery pack

15. Battery pack release button

16. Hex wrench

17. Hex wrench storage

Assembly

Warning! Before assembly, remove the battery (14) from the

tool.

Charging the battery (Fig. A)

The battery needs to be charged before rst use and whenev-

er it fails to produce sufcient power on jobs that were easily

done before. The battery may become warm while charging;

this is normal and does not indicate a problem.

Warning! Do not charge the battery at ambient temperatures

below 10 °C or above 40 °C. Recommended charging tem-

perature: approx. 24 °C.

Note: The charger will not charge a battery if the cell tempera-

ture is below approximately 10 °C or above 40 °C.

ENGLISH

(Original instructions)

The battery should be left in the charger and the charger

will begin to charge automatically when the cell temperature

warms up or cools down.

uTo charge the battery (14), insert it into the charger (18).

The battery will only t into the charger in one way. Do

not force. Be sure that the battery is fully seated in the

charger.

uPlug in the charger and switch on at the mains.

The charging indicator (18a) will blink.

The charge is complete when the charging indicator (18a)

switches to continuously on. The charger and the battery can

be left connected indenetely. The LED will switch on as the

charger occasionally tops up the battery charge.

uCharge discharged batteries within 1 week. Battery life will

be greatly diminished if stored in a discharged state.

Charger LED Modes

Charging:

Green LED Intermittent

Fully Charged:

Green LED Solid

Hot/Cold Pack Delay:

Green LED Intermittent

Red LED Solid

Note: The compatible charger(s) will not charge a faulty

battery pack. The charger will indicate a faulty battery pack by

refusing to light.

Note: This could also mean a problem with a charger. If the

charger indicates a problem, take the charger and battery

pack to be tested at an authorized service centre.

Leaving the battery in the charger

The charger and battery pack can be left connected with the

LED glowing indenitely. The charger will keep the battery

pack fresh and fully charged.

Hot/Cold Pack Delay

When the charger detects a battery that is too hot or too cold,

it automatically starts a Hot/Cold Pack Delay, the green LED

(18a) will ash intermittently, while the red LED (18b) will

remain on continuously, suspending charging until the battery

has reached an appropriate temperature. The charger then

automatically switches to the pack charging mode. This

feature ensures maximum battery life.

Battery state of charge indicator (Fig. B)

The battery includes a state of charge indicator to quickly

determine the extent of battery life as shown in gure B. By

pressing the state of charge button (14a) you can easily view

the charge remaining in the battery as illustrated in gure B.

Installing and Removing the Battery Pack (Fig. L)

Warning! Ensure the tool/appliance is in the off position

before inserting the battery pack.

Note: For best results, make sure your battery pack is

fully charged.

uTo install the battery pack (14) into the tool handle, align

the battery pack with the rails inside the tool’s handle

and slide it into the handle until the battery pack is rmly

seated in the tool and ensure that it does not disengage.

uTo remove the battery pack from the tool, press the bat-

tery pack release button (15) and rmly pull the battery

pack out of the tool handle. Insert it into the charger as

described in the charger section of this manual.

Installing the guide bar and saw chain (Fig. D-H)

Warning! Sharp chain. Always wear protective gloves when

handling the chain. The chain is sharp and can cut you when

it is not running.

Warning! Sharp moving chain. To prevent accidental

operation, ensure that battery is removed from the tool before

performing the following operations. Failure to do this could

result in serious personal injury.

If the saw chain (5) and guide bar (4) are packed separately in

the carton, the chain has to be attached to the bar, and both

must be attached to the body of the tool.

uPlace the saw on a at, rm surface.

uRotate the bar lock nut (7) counterclockwise with the hex

wrench (16) provided.

uRemove sprocket cover (6), and bar lock nut (7).

uWearing protective gloves, grasp the saw chain (5) and

wrap it around the guide bar (4), ensuring the teeth are

facing the correct direction (Fig. H).

uEnsure the chain is properly set in the slot around the

entire guide bar.

uPlace the saw chain around the sprocket (19). While lining

up the slot on the guide bar with chain tensioning pin (20),

and the bolt (21), on the base of the tool as shown in

Fig. E.

uOnce in place, hold the bar still, replace sprocket

cover (6).

ENGLISH (Original instructions)

Install the rear of the sprocket cover rst, rotate it down

and make sure the bolt hole on the cover lines up with the

bolt (21), on the main housing.

uInstall the bar lock nut (7) and rotate clockwise with the

hex wrench (16) provided until snug, then loosen nut one

full turn, so that the saw chain can be properly tensioned.

uRotate the chain tensioning screw (8) clockwise to

increase tension as shown in Fig. D. Make sure the saw

chain (5) is snug around the guide bar (4). Tighten the bar

lock nut (7) until snug.

uFollow the instructions in the section Adjusting Chain Ten-

sion.

Adjusting chain tension (Fig. D-H)

Warning! Incorrect saw chain tension can cause the saw

chain to come off of the guide bar and could cause serious

injury or death.

Note: Saw chain tension should be adjusted regularly before

each use.

uWith the saw still on a rm surface check the saw chain (5)

tension. The tension is correct when the saw chain snaps

back after being pulled (3 mm) away from the guide

bar (4) with light force from the middle nger and thumb

as shown in Fig. F. There should be no “sag” between the

guide bar and the saw chain on the underside as shown in

Fig. G.

uTo adjust saw chain tension, loosen bar lock nut (7).

uRotate the chain tensioning screw ( 8 ) in the front

of the housing using the at screwdriver end of the

hex wrench (16).

uCheck saw chain tension, adjust if needed.

uDo not over-tension the saw chain as this will lead to

excessive wear and will reduce the life of the guide bar

and saw chain. Overtensioning also reduces the amount

of cuts you will get per battery charge.

uOnce saw chain tension is correct, tighten bar lock nut (7)

until snug. Torque the bar lock nut (7) to (8 Nm).

uA new chain stretches slightly during the rst few hours of

use. It is important to check the tension frequently (after

disconnecting battery remove the battery pack) during the

rst two hours of use.

Replacing the saw chain (Fig. D-H)

Warning! Sharp moving chain. To prevent accidental

operation, ensure that battery is removed from the tool before

performing the following operations. Failure to do this could

result in serious personal injury.

Caution: Sharp chain. Always wear protective gloves when

handling the chain. The chain is sharp and can cut you when it

is not running.

Caution: The chain speed of this product is 8.6 m/s. Only use

chains that are rated at greater than 8.6 m/s.

uPlace the saw on a at, rm surface.

uRemove sprocket cover (6) as described in Installing the

Guide Bar and Saw Chain section.

uTo remove the saw chain (5), rotate the chain tensioning

screw (8) in the front of the housing using the at screw-

driver end of the wrench. Turning the screw counterclock-

wise allows the guide bar (4) to recede and reduces the

tension on the chain so that it may be removed.

uWearing protective gloves, grasp the saw chain and lift the

worn saw chain out of the groove in the guide bar.

uFlip guide bar over every time you replace the chain to

ensure even wear.

uPlace the new chain in the slot of the guide bar, making

sure the saw teeth are facing the correct direction by

matching the arrow and graphic of the saw chain on the

sprocket cover (6) shown in Fig. H.

uFollow instructions for Installing the Guide Bar and

Saw Chain.

Replacement chain and bar are available from your nearest

authorized service center.

This chainsaw requires replacement (304 mm) chain.

Replacement (304 mm) bar.

Saw chain and guide bar oiling (Fig. I)

Auto oiling system

This chain saw is equipped with an auto oiling system that

keeps the saw chain and guide bar constantly lubricated.

The oil level indicator (10) shows the level of the oil in the

chain saw. If the oil level is less than a quarter full, remove the

battery from the chain saw and rell the oil tank with the

correct type of oil.

Always empty oil tank when nished cutting.

Always empty oil tank before storing this unit.

Note: Do not operate this chain saw without oil.

Note: Always use a high-quality, biodegradable bar and chain

oil for proper saw chain and bar lubrication. When pruning

trees, vegetable-based bar and chain oil is recommended, as

mineral-based oils may harm living trees. Never use dirty,

used, or contaminated oil. Doing so may damage the tool.

Filling the oil reservoir

uUnscrew counterclockwise and then remove the oil

cap (9). Fill the reservoir with the recommended bar and

chain oil until the oil level has reached the top of the oil

level indicator (10).

uRet the oil cap and tighten clockwise.

uPeriodically switch the chain saw off and check the oil

level indicator to ensure the bar and chain are being

properly oiled. Periodically switch the chain saw off and

check the oil level indicator to ensure the bar and chain

are being properly oiled.

ENGLISH

(Original instructions)

Transporting chainsaw (Fig. J)

uAlways turn unit off, remove the battery and cover the

guide bar (4) with the guide bar scabbard (11) when

transporting the saw.

Operation

Warning! To reduce the risk of serious personal injury, turn

unit off and remove the battery pack before making any

adjustments or removing/installing attachments or

accessories. An accidental start-up can cause injury.

Proper hand position (Fig. K)

Warning! To reduce the risk of serious personal injury, Always

use proper hand position as shown.

Warning! To reduce the risk of serious personal injury, always

hold securely in anticipation of a sudden reaction.

Proper hand position requires the left hand on the front

handle (13), with the right hand on the rear handle (12).

Operating the chain saw (Fig. K)

Warning! Read and understand all instructions. Failure to

follow all instructions listed below may result in electric shock,

re and/or serious personal injury.

uGuard Against Kickback which can result in severe injury

or death. See General Power Tool Safety Warnings and

General Chain saw Safety Warnings, and Causes and

Operator Prevention of Kickback and Kickback Safety

Features, to avoid the risk of kickback.

uDo not overreach. Do not cut above chest height. Make

sure your footing is rm. Keep feet apart. Divide your

weight evenly on both feet.

uUse a rm grip with your left hand on the front handle (13)

and your right hand on the rear handle (12) so that your

body is to the left of the guide bar (4).

uDo not hold chain saw by chain brake/front hand

guard (3). Keep elbow of left arm locked so that left arm is

straight to withstand a kickback.

Warning! Never use a cross-handed grip (left hand on the

rear handle and right hand on the front handle).

Warning! Never allow any part of your body to be in line with

the guide bar when operating the chain saw.

uNever operate while in a tree, in any awkward position

or on a ladder or other unstable surface. You may lose

control of saw causing severe injury.

uKeep the chain saw running at full speed the entire time

you are cutting.

uAllow the saw chain to cut for you. Exert only light pres-

sure. Do not put pressure on chain saw at end of cut.

Warning! When not in use always have the chain brake

engaged and battery removed.

Setting the chain brake (Fig. K, L)

Your chain saw is equipped with a chain braking system which

will stop the chain quickly in case of kickback.

uEnsure the chain brake/front hand guard (3) is in the

forward position.

uInsert the battery pack (14) into the tool.

uPull the chain brake/front hand guard (3) towards the

front handle (13) into the “set/ready” position as shown in

Fig. L.

uThe tool is now ready to use.

uAfter use, return the chain brake/front hand guard to the

forward position.

uRemove the battery.

Note: In the event of kickback, your left hand will come in

contact with the front guard, pushing it forward, toward the

workpiece. This will stop the tool.

Testing the chain brake (Fig. L)

Test the chain brake before every use to make sure it

operates correctly.

uPlace the tool on a at, rm surface. Make sure the saw

chain (5) is clear of the ground.

uGrip the tool rmly with both hands and turn the chain

saw on.

uRotate your left hand forward around the front handle (13)

so the back of your hand comes in contact with the chain

brake/front hand guard (3) and push it forward, toward the

workpiece. The saw chain should stop immediately.

Note: If saw does not stop immediately, stop use of tool and

bring it to an authorized service center nearest you.

Warning! Make sure to set chain brake before cutting.

On/Off switch (Fig. M)

Always be sure of your footing and grip the chain saw rmly

with both hands with the thumb and ngers encircling

both handles.

uTo turn the unit on, push the lock-off lever (2) in, shown in

Fig. M, and squeeze the trigger switch (1). Once the unit is

running, you may release the lock-off lever.

uIn order to keep the unit running you must continue to

squeeze the trigger. To turn the unit off, release the trigger.

Saw chain sharpening (Fig. N - P)

Caution: Sharp chain. Always wear protective gloves when

handling the chain. The chain is sharp and can cut you when it

is not running.

Warning! Sharp moving chain. To prevent accidental

operation, ensure that battery is removed from the tool before

performing the following operations. Failure to do this could

result in serious personal injury.

Note: The cutters will dull immediately if they touch the ground

or a nail while cutting.

ENGLISH (Original instructions)

To get the best possible performance from your chainsaw it is

important to keep the teeth of the saw chain sharp. Follow

these helpful tips for proper saw chain sharpening:

uFor best results use a 4.5 mm le and a le holder or ling

guide to sharpen your saw chain. This will ensure you

always get the correct sharpening angles.

uPlace the le holder at on the top plate and depth gauge

of the cutter.

uKeep the correct top plate (22) ling angle line of 30 ° on

your le guide parallel with your chain (le at 60 ° from

chain viewed from the side) as shown.

uSharpen cutters on one side of the chain rst. File from

the inside of each cutter to the outside. Then turn your

saw around and repeat the processes (2, 3, 4) for cutters

on the other side of the chain.

Note: Use a at le to le the tops of the rakers (portion of

chain link in front of the cutter) so they are about (0.635 mm)

below the tips of the cutters as shown below.

uKeep all cutter lengths equal as shown in Fig. O.

uIf damage is present on the chrome surface of the top

plates or side plates, le back until such damage is re-

moved.

Caution: After ling, the cutter will be sharp, use extra caution

during this process.

Note: Each time the chain is sharpened, it loses some of the

low kickback qualities and extra caution should be used. It is

recommended that a saw chain be sharpened no more than

four times.

Hex wrench storage (Fig. Q)

When not in use the hex wrench (16) should be stored in the

hex wrench storage (17) area located under the tool.

Pull the hex wrench from the hex wrench storage area to

remove it.

Push the hex wrench into the hex wrench storage area to

store it.

Stanley Track Wall System (Fig. R,S)

Warning! To reduce the risk of serious personal injury, turn

unit off and remove the battery pack before making any

adjustments or removing/installing attachments or

accessories. An accidental start-up can cause injury.

Warning! To reduce the risk of serious personal injury, do not

use a damaged Stanley Track Wall System integral hang hook

or Stanley Track Wall System. A damaged Stanley Track Wall

System integral hang hook or Stanley Track Wall System

Trackwall will not support the weight of the tool.

Warning! To reduce the risk of serious personal injury, DO

NOT suspend tool overhead or suspend objects from the

integral hang hook. ONLY suspend tool on the Stanley Track

Wall System Trackwall using the integral hang hook.

Warning! Stanley Track Wall System integral hang hook is

intended to mount the tool onto a Stanley Track Wall System

Trackwall rail.

Do not use the integral hang hook to mount the tool to any

other surface.

Warning! Stanley Track Wall System integral hang hook is not

a belt hook.

Warning! When hanging objects on a Stanley Track Wall

System Trackwall rail, adequately space the tools in order to

not exceed 35 kg per linear foot.

Warning! Before using the tool make sure that the Stanley

Track Wall System integral hang hook is returned to its

original position.

Important: Stanley Track Wall System accessories mount

compatible tools securely to the Stanley Track Wall System.

Turn tool off, remove the battery pack and

remove accessories.

Install guide bar scabbard (11) onto the guide bar (4).

Caution: Any product with exposed cutting teeth must have

them covered securely if it is to be on the Stanley Track Wall

System Trackwall.

Mount the integral hang hook (23) to the Stanley Track Wall

System Trackwall as shown in Fig. R,S. It clicks when locked

into position.

Note: Stanley Track Wall System accessories for use with

your tool are available at extra cost from your local dealer or

authorized service center.

Common cutting techniques

Felling (Fig. T, U)

The process of cutting down a tree. Do not fell trees in high

wind conditions.

Warning! Felling can result in injury. It should only be

performed by a trained person.

A retreat path should be planned and cleared as necessary

before cuts are started. The retreat path should extend back

and diagonally to the rear of the expected line of fall as

shown below.

uBefore felling is started, consider the natural lean of the

tree, the location of larger branches and the wind direction

to judge which way the tree will fall. Have wedges (wood,

plastic or aluminum) and a heavy mallet handy. Remove

dirt, stones, loose bark, nails, staples, and wire from the

tree where the felling cuts are to be made.

uNotching Undercut - Make the notch 1/3 of the diameter of

the tree, perpendicular to the direction of the fall. Make the

lower horizontal notching cut rst. This will help to avoid

pinching of either the saw chain or the guide bar when the

second notch cut is being made as shown below.

uFelling Back Cut - Make the felling back cut at least

51 mm higher than the horizontal notching cut. Keep the

felling back cut parallel to the horizontal notching cut.

ENGLISH

(Original instructions)

Make the felling back cut so enough wood is left to act as

a hinge. The hinge wood keeps the tree from twisting and

falling in the wrong direction.

Do not cut through the hinge as shown below.

uAs the felling cut gets close to the hinge the tree should

begin to fall. If there is any chance that the tree may

not fall in the desired direction or it may rock back and

bind the saw chain, stop cutting before the felling cut is

complete and use wedges to open the cut and drop the

tree along the desired line of fall. When the tree begins to

fall remove the chainsaw from the cut, stop the motor, put

the chainsaw down, then use the retreat path planned. Be

alert for overhead limbs falling and watch your footing.

Limbing (Fig. V)

Removing the branches from a fallen tree. When limbing,

leave larger lower limbs to support the log off the ground.

Remove the small limbs in one cut. Branches under tension

should be cut from the bottom of the branch towards the top

to avoid binding the chainsaw as shown in Fig. V. Trim limbs

from opposite side keeping tree stem between you and saw.

Never make cuts with saw between your legs or straddle the

limb to be cut.

Bucking (Fig. W, X, Y, Z)

Warning! Recommend that rst-time users should practice

cutting on a saw horse.

Cutting a felled tree or log into lengths. How you should

cut depends on how the log is supported. Use a saw horse

whenever possible as shown in Fig. W.

uAlways start a cut with the saw chain running at full speed.

uPlace the bottom spike of the chainsaw behind the area of

the initial cut as shown in Fig. W.

uTurn the chainsaw on then rotate the saw chain and bar

down into the tree, using the spike as a hinge.

uOnce the chainsaw gets to a 45 ° angle, level the chain-

saw again and repeat steps until you cut fully through.

uWhen the tree is supported along its entire length Fig. X,

make a cut from the top (overbuck), but avoid cutting the

earth as this will dull your saw quickly.

uWhen supported at one end Fig. Y, rst, cut 1/3 the

diameter from the underside (underbuck). Then make

the nishing cut by overbucking to meet the rst cut as

shown in Fig Y.

uWhen supported at both ends Fig. Z. First, cut 1/3 down

from the top overbuck. Then make the nished cut by un-

derbucking the lower 2/3 to meet the rst cut as shown in

Fig. Z.

Troubleshooting

Problem Possible cause Possible solution

Tool will not start Lock button not

pressed.

Press the lock

button.

Battery not tted Fit the battery

Battery not charged Charge the battery

Battery not tted

corectly

Remove then re-t the

battery

Chain does not stop

within 2 seconds

when the tool is

switched off

Chain tension is too

slack

Check chain tension

Bar/chain appear hot/

smoking

Oil tank empty Check oil tank level

Oil hole blocked on

chain bar

Clean oil holes and

clear the groove around

the edge of the

chainbar.

Chain tension is too

tight

Check chain tension

Guide bar sprocket

nose needs greasing

Oil the guide bar

sprocket nose

Chainsaw does not

cut well

Chain on backwards Check/modify chain

direction

Sharpen

Chainsaw not using

oil

Debris in tank Empty oil from tank and

replace

Oil hole in cap

blocked

Remove debris from

hole

Debris in chain bar Remove debris and

clean the chain bar

Debris in oil outlet Remove debris

Chainsaw stops

suddnely during

use

Battery depleted Check the charge on

the battery by pressing

the state of charge

indicator. Re-charge

battery if required.

Battery too hot Leave the battery to

cool for at least 30

minutes before

proceeding or

charging.

Current limit

protection

Restart the chainsaw.

Let the tool work at its

own pace. Do not

overload .

Maintenance

Regular maintenance ensures a long effective life for the tool.

We recommend you make the following checks on a regular

basis.

Warning! Before performing any maintenance on power tools:

u Switch off and disconnect the tool from the mains supply.

ENGLISH (Original instructions)

Oil level

The level in the reservoir should not be allowed to fall below

a quarter full.

Saw chain and guide bar

u After every few hours of use and before storage,

remove the guide bar and the saw chain and clean them

thoroughly.

u Make sure that the guard is clean and free from debris.

u Oil sprocket nose and chain bar via the sprocket

lubrication holes. This ensures an even distribution of

wear around the guide bar rails.

Saw chain sharpening

If you are to get the best possible performance from the tool it

is important to keep the teeth of the saw chain sharp.

Guidance for this procedure is found on the sharpener

package.

Replacing worn out saw chains

Replacement saw chains are available through retailers or

STANLEY FATMAX service agents. Always use genuine spare

parts.

Saw chain sharpness

The saw chain cutters will blunt immediately if they touch the

ground or a nail while cutting.

Saw chain tension

Regularly check the saw chain tension.

What to do if your chainsaw needs repair?

Your chainsaw is manufactured in accordance with the

relevant safety requirements. Repairs should only be carried

out by a qualied person using original spare parts otherwise

this may result in considerable danger to the user. We

recommend you keep this user manual in a safe place.

Protecting the environment

Separate collection. Products and batteries

marked with this symbol must not be disposed of

with normal household waste.

Products and batteries contain materials that can be recov-

ered or recycled reducing the demand for raw materials.

Please recycle electrical products and batteries accord-

ing to local provisions. Further information is available at

www.2helpU.com

Technical data

SFMCCS730

Voltage VDC

Bar length mm

300

Chain speed (No-load) m/s

6.7

Max cutting length mm

250

Oil capacity ml

150

Weight kg 2.51 (without the saw chain, guide bar, guide bar cover, oil, battery)

Charger SFMCB11 SFMCB12 SFMCB14

Input Voltage VAC 230 230 230

Output Voltage VDC 18 18 18

Current A 1.25 2 4

Battery SFMCB201 SFMCB202 SFMCB204 SFMCB206

Voltage VDC 18 18 18 18

Capacity Ah 1.5 2.0 4.0 6.0

Type Li-Ion Li-Ion Li-Ion Li-Ion

Level of sound pressure according to EN 62841:

LpA (sound pressure) 87 dB(A), Uncertainty (K) 3 dB(A)

LWA (sound power) 99 dB(A), Uncertainty (K) 1.6 dB(A)

Vibration total values (triax vector sum) according to EN 62841:

Vibration emission value (ah) 6.5 m/s2, uncertainty (K) 1.5 m/s2

Supply of Machinery (Safety)

Regulations 2008

SFMCCS730 – Compact Chainsaw

STANLEY FATMAX declares that these products described

under “technical data” are in compliance with:

The Supply of Machinery (Safety) Regulations, 2008, S.I.

2008/1597 (as amended),

EN 62841-1:2015+A11:2022, EN 62841-4-1:2020.

The Noise Emission in the Environment by Equipment for use

Outdoors Regulations 2001, S.I. 2001/1701 (as amended).

Schedule 8.

LWA (measured sound power level) 99 dB(A), uncertainty (K)

= 1.6 dB (A),

LWA (guaranteed sound power) 101 dB(A).

These products conform to the following UK Regulations:

Electromagnetic Compatibility Regulations, 2016,

S.I.2016/1091 (as amended).

The Restriction of the Use of Certain Hazardous Substances

in Electrical and Electronic Equipment Regulations 2012, S.I.

2012/3032 (as amended).

ENGLISH

(Original instructions)

For more information, please contact STANLEY FATMAX at

the following address or refer to the back of the manual.

The undersigned is responsible for compilation of the technical

le and makes this declaration on behalf of

STANLEY FATMAX

Paul Featherstone

Product Director - Outdoor Products Group

STANLEY FATMAX, 270 Bath Road, Slough

Berkshire, SL1 4DX

United Kingdom28/06/2023

EC declaration of conformity

MACHINERY DIRECTIVE

SFMCCS730 – Compact Chainsaw

STANLEY FATMAX declares that these products described

under "technical data" are in compliance with: 2006/42/EC,

EN 62841-1:2015+A11:2022, EN 62841-4-1:2020,

2000/14/EC, Annex V

LWA (measured sound power level) 99 dB(A), uncertainty (K)

= 1.6 dB (A),

LWA (guaranteed sound power) 101 dB(A)

These products also comply with Directive

2014/30/EU and 2011/65/EU.

For more information, please contact STANLEY FATMAX at

the following address or refer to the back of the manual.

The undersigned is responsible for compilation of the

technical le and makes this declaration on behalf of

STANLEY FATMAX

Patrick Diepenbach

General Manager, Benelux

Stanley FatMax,

Egide Walschaertsstraat 14-18

2800 Mechelen, Belgium

28/06/2023

Guarantee

STANLEY FATMAX is confident of the quality of its products

and offers consumers a 12 month guarantee from the date

of purchase. This guarantee is in addition to and in no way

prejudices your statutory rights. The guarantee is valid within

the territories of the Member States of the European Union

and the European Free Trade Area and the United Kingdom.

To claim on the guarantee, the claim must be in accordance

with STANLEY FATMAX Terms and Conditions and you will

need to submit proof of purchase to the seller or an authorised

repair agent. Terms and conditions of the STANLEY FATMAX

1 year guarantee and the location of your nearest authorised

repair agent can be obtained on the Internet at www.2helpU.

com, or by contacting your local STANLEY FATMAX office at

the address indicated in this manual.

Please visit our website www.stanley.eu/3 to register Please

visit our website www.stanley.eu/3 to register

your new STANLEY FATMAX product and receive updates on

new products and special offers.

(Übersetzung der ursprünglichen Anweisungen)

DEUTSCH

Verwendungszweck

Ihre STANLEY FATMAX Kompakt-Kettensäge SFMCCS730

ist für leichte Säge- und Gehölzschnittaufgaben vorgesehen.

Dieses Gerät ist zum gewerblichen und privaten Einsatz

vorgesehen.

Sicherheitshinweise

Allgemeine Sicherheitswarnhinweise für

Elektrowerkzeuge

Warnung! Beachten Sie alle Sicherheits-

hinweise, Anweisungen, Darstellungen und

Daten, die Sie mit dem Gerät erhalten. Wenn

Sie die folgenden Anweisungen nicht beachten,

kann es zu elektrischem Schlag, Feuer und/oder

schweren Verletzungen kommen.

Bewahren Sie alle Warnhinweise und alle Anweisungen

gut auf. Der Begriff „Elektrowerkzeug“ in den Warnhinweisen

bezieht sich auf Ihr netzbetriebenes Elektrowerkzeug

(mit Kabel) oder auf Ihr akkubetriebenes (kabelloses)

Elektrowerkzeug.

1. Sicherheit im Arbeitsbereich

a. Halten Sie den Arbeitsbereich sauber und gut

ausgeleuchtet. Unaufgeräumte oder dunkle Bereiche

begünstigen Unfälle.

b. Betreiben Sie das Elektrowerkzeug nicht in

explosionsgefährdeten Umgebungen, in denen sich

z. B. brennbare Flüssigkeiten, Gase oder Staub

benden. Elektrowerkzeuge erzeugen Funken, die den

Staub oder die Dämpfe entzünden können.

c. Halten Sie Kinder und andere Personen während der

Benutzung von Elektrowerkzeugen fern. Ablenkung

kann dazu führen, dass Sie die Kontrolle über das Gerät

verlieren.

2. Elektrische Sicherheit

a. Der Stecker des Elektrogerätes muss in die Steckdose

passen. Ändern Sie niemals den Stecker in

irgendeiner Form. Verwenden Sie keinerlei

Adapterstecker an geerdeten Elektrogeräten.

Unveränderte Stecker und passende Steckdosen mindern

die Gefahr eines elektrischen Schlages.

b. Vermeiden Sie Körperkontakt mit geerdeten Flächen,

wie Rohren, Radiatoren, Herden und Kühlgeräten. Es

besteht eine erhöhte Gefahr für einen elektrischen Schlag,

wenn Ihr Körper geerdet ist.

c. Setzen Sie Elektrogeräte keinem Regen oder feuchter

Umgebung aus. Wenn Wasser in das Elektrowerkzeug

eindringt, erhöht sich die Gefahr eines elektrischen

Schlages.

d. Verwenden Sie das Kabel ordnungsgemäß.

Verwenden Sie niemals das Kabel, um das

Elektrowerkzeug zu tragen oder durch Ziehen vom

Netz zu trennen. Halten Sie das Kabel fern von Hitze,

Öl, scharfen Kanten oder beweglichen Teilen.

Beschädigte oder verhedderte Kabel erhöhen die Gefahr

eines elektrischen Schlags.

e. Verwenden Sie nur für den Außenbereich zugelassene

Verlängerungskabel, wenn Sie mit dem Gerät im

Freien arbeiten. Die Verwendung eines für den

Außenbereich zugelassenen Verlängerungskabels

verringert das Risiko eines elektrischen Schlags.

f. Wenn das Gerät in einer feuchten Umgebung

verwendet werden muss, schließen Sie es unbedingt

an eine Steckdose mit Fehlerstromschutzschalter

(FI-Schalter) an. Ein Fehlerstromschutzschalter verringert

das Risiko eines elektrischen Schlags.

3. Sicherheit von Personen

a. Seien Sie aufmerksam, achten Sie darauf, was Sie tun,

und gehen Sie sachgerecht mit einem Gerät um.

Benutzen Sie Elektrowerkzeuge nicht, wenn Sie müde

sind oder unter dem Einuss von Drogen, Alkohol

oder Medikamenten stehen. Ein Moment der

Unachtsamkeit beim Betrieb eines Elektrowerkzeugs kann

zu schweren Verletzungen führen.

b. Tragen Sie persönliche Schutzausrüstung. Tragen Sie

immer einen Augenschutz. Das Tragen persönlicher

Schutzausrüstung, wie Staubmaske, rutschfeste

Sicherheitsschuhe, Schutzhelm oder Gehörschutz, je

nach Art und Einsatz des Elektrowerkzeugs, verringert das

Risiko von Verletzungen.

c. Vermeiden Sie unbeabsichtigtes Starten.

Vergewissern Sie sich, dass das Gerät ausgeschaltet

ist, bevor Sie es an eine Steckdose oder einen Akku

anschließen, es hochheben oder tragen. Wenn Sie

beim Tragen des Geräts den Finger am Schalter haben

oder das Gerät eingeschaltet an die Stromversorgung

anschließen, kann dies zu Unfällen führen.

d. Entfernen Sie Einstell- oder Schraubenschlüssel,

bevor Sie das Gerät einschalten. Werkzeuge oder

Schlüssel, die an rotierenden Teilen des Geräts

angebracht sind, können zu Verletzungen führen.

e. Vermeiden Sie eine anormale Körperhaltung. Sorgen

Sie für einen sicheren Stand und halten Sie jederzeit

das Gleichgewicht. Dadurch können Sie das

Elektrowerkzeug in unerwarteten Situationen besser

kontrollieren.

f. Tragen Sie geeignete Kleidung. Tragen Sie keine weite

Kleidung und keinen Schmuck. Halten Sie Ihre Haare,

Kleidung und Handschuhe von beweglichen Teilen

fern. Lose sitzende Kleidung, Schmuck oder lange Haare

können sich in den beweglichen Teilen verfangen.

Sidan laddas ...

Stanley SFMCCS730B Användarmanual

varumärke: Stanley

Modell: SFMCCS730B

Kategori: Sladdlösa motorsågar

Typ: Användarmanual

Denna manual är också lämplig för

SFMCCS730M1

Ladda ner pdf

Rapportera

på andra språk

italiano: Stanley SFMCCS730B Manuale utente
español: Stanley SFMCCS730B Manual de usuario
Deutsch: Stanley SFMCCS730B Benutzerhandbuch
português: Stanley SFMCCS730B Manual do usuário
français: Stanley SFMCCS730B Manuel utilisateur
dansk: Stanley SFMCCS730B Brugermanual
Nederlands: Stanley SFMCCS730B Handleiding

Stanley SFMCCS730B Användarmanual

Denna manual är också lämplig för

Stanley SFMCCS730B Användarmanual

på andra språk

Andra dokument