Yamaha EMX 5016CF Användarmanual

varumärke: Yamaha

Modell: EMX 5016CF

Kategori: Ljudmixer

Typ: Användarmanual

Denna manual är också lämplig för

EMX5016CF

Owner’s Manual

Bedienungsanleitung

Mode d’emploi

Manual de instrucciones

Owner’s Manual

Bedienungsanleitung

Mode d’emploi

Manual de instrucciones

Making the Most of Your Mixer

Pages 12 to 18

Quick Guide

Pages 7 to 11

POWERED MIXER

EMX5016CF Owner’s Manual

The above warning is located on the rear of the unit.

Explanation of Graphical Symbols

The lightning ﬂash with arrowhead symbol

within an equilateral triangle is intended to alert

the user to the presence of uninsulated

“dangerous voltage” within the product’s

enclosure that may be of sufﬁcient magnitude to

constitute a risk of electric shock to persons.

The exclamation point within an equilateral

triangle is intended to alert the user to the

presence of important operating and

maintenance (servicing) instructions in the

literature accompanying the product.

IMPORTANT SAFETY INSTRUCTIONS

1 Read these instructions.

2 Keep these instructions.

3 Heed all warnings.

4 Follow all instructions.

5 Do not use this apparatus near water.

6 Clean only with dry cloth.

7 Do not block any ventilation openings. Install in

accordance with the manufacturer’s instructions.

8 Do not install near any heat sources such as radiators,

heat registers, stoves, or other apparatus (including

ampliﬁers) that produce heat.

9 Do not defeat the safety purpose of the polarized or

grounding-type plug. A polarized plug has two blades

with one wider than the other. A grounding type plug

has two blades and a third grounding prong. The wide

blade or the third prong are provided for your safety. If

the provided plug does not ﬁt into your outlet, consult

an electrician for replacement of the obsolete outlet.

10 Protect the power cord from being walked on or pinched

particularly at plugs, convenience receptacles, and the

point where they exit from the apparatus.

11 Only use attachments/accessories speciﬁed by the

manufacturer.

12 Use only with the cart, stand,

tripod, bracket, or table speciﬁed

by the manufacturer, or sold with

the apparatus. When a cart is

used, use caution when moving

the cart/apparatus combination

to avoid injury from tip-over.

13 Unplug this apparatus during

lightning storms or when unused for long periods of

time.

14 Refer all servicing to qualiﬁed service personnel.

Servicing is required when the apparatus has been

damaged in any way, such as power-supply cord or plug

is damaged, liquid has been spilled or objects have

fallen into the apparatus, the apparatus has been

exposed to rain or moisture, does not operate normally,

or has been dropped.

(98-6500)

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE

COVER (OR BACK). NO USER-SERVICEABLE

PARTS INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.

IMPORTANT

Please record the serial number of this unit in the space below.

Model:

Serial No.:

The serial number is located on the bottom or rear of the unit.

Retain this Owner’s Manual in a safe place for future reference.

EMX5016CF Owner’s Manual

(5)-4

PRECAUTIONS

PLEASE READ CAREFULLY BEFORE PROCEEDING

* Please keep this manual in a safe place for future reference.

WARNING

Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from electrical

shock, short-circuiting, damages, ﬁre or other hazards. These precautions include, but are not limited to, the following:

• Only use the voltage speciﬁed as correct for the device. The required voltage is

printed on the name plate of the device.

• Use only the included power cord.

• Do not place the power cord near heat sources such as heaters or radiators, and do

not excessively bend or otherwise damage the cord, place heavy objects on it, or

place it in a position where anyone could walk on, trip over, or roll anything over it.

• Be sure to connect to an appropriate outlet with a protective grounding

connection. Improper grounding can result in electrical shock.

• Do not open the device or attempt to disassemble the internal parts or modify

them in any way. The device contains no user-serviceable parts. If it should

appear to be malfunctioning, discontinue use immediately and have it inspected

by qualiﬁed Yamaha service personnel.

• Do not expose the device to rain, use it near water or in damp or wet conditions,

or place containers on it containing liquids which might spill into any openings.

• Never insert or remove an electric plug with wet hands.

• If the power cord or plug becomes frayed or damaged, or if there is a sudden

loss of sound during use of the device, or if any unusual smells or smoke

should appear to be caused by it, immediately turn off the power switch,

disconnect the electric plug from the outlet, and have the device inspected by

qualiﬁed Yamaha service personnel.

• If this device should be dropped or damaged, immediately turn off the power

switch, disconnect the electric plug from the outlet, and have the device

inspected by qualiﬁed Yamaha service personnel.

CAUTION

Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or damage

to the device or other property. These precautions include, but are not limited to, the following:

• Remove the electric plug from the outlet when the device is not to be used for

extended periods of time, or during electrical storms.

• When removing the electric plug from the device or an outlet, always hold the

plug itself and not the cord. Pulling by the cord can damage it.

• Before moving the device, remove all connected cables.

• When setting up the device, make sure that the AC outlet you are using is easily

accessible. If some trouble or malfunction occurs, immediately turn off the

power switch and disconnect the plug from the outlet. Even when the power

switch is turned off, electricity is still ﬂowing to the product at the minimum

level. When you are not using the device for a long time, make sure to unplug

the power cord from the wall AC outlet.

• If this device is to be mounted in an EIA-standard rack, leave the back of the rack

open and make sure that it is at least 10 cm away from walls or surfaces. Also, if

this device is to be mounted with devices that tend to generate heat, such as

power ampliﬁers, be sure to keep an adequate gap between this device and the

heat-generating devices or install ventilation panels to prevent high

temperatures from developing inside this device.

Inadequate ventilation can result in overheating, possibly causing damage to the

device(s), or even ﬁre.

•Avoid setting all equalizer controls and faders to their maximum. Depending on

the condition of the connected devices, doing so may cause feedback and may

damage the speakers.

• Do not expose the device to excessive dust or vibrations, or extreme cold or heat

(such as in direct sunlight, near a heater, or in a car during the day) to prevent

the possibility of panel disﬁguration or damage to the internal components.

• Do not place the device in an unstable position where it might accidentally fall over.

• Do not block the vents. This device has ventilation holes at the front and rear to

prevent the internal temperature from becoming too high. In particular, do not

place the device on its side or upside down. Inadequate ventilation can result in

overheating, possibly causing damage to the device(s), or even ﬁre.

• Do not use the device in the vicinity of a TV, radio, stereo equipment, mobile

phone, or other electric devices. Doing so may result in noise, both in the device

itself and in the TV or radio next to it.

• Before connecting the device to other devices, turn off the power for all devices.

Before turning the power on or off for all devices, set all volume levels to

minimum.

• Use only speaker cables for connecting speakers to the speaker jacks. Use of

other types of cables may result in ﬁre.

• Do not use speaker cables with a metal-housing connector. Doing so may result

in electrical shock due to differences in voltage. Use speaker cables with a non-

metal-housing connector, or with a insulated-housing connector.

• When turning on the AC power in your audio system, always turn on the device

or external power ampliﬁers LAST, to avoid speaker damage. When turning the

power off, the device or external power ampliﬁers should be turned off FIRST for

the same reason.

• Do not insert your ﬁngers or hands in any gaps or openings on the device

(vents, etc.).

•Avoid inserting or dropping foreign objects (paper, plastic, metal, etc.) into any

gaps or openings on the device (vents, etc.) If this happens, turn off the power

immediately and unplug the power cord from the AC outlet. Then have the

device inspected by qualiﬁed Yamaha service personnel.

• Do not use the speakers or headphones for a long period of time at a high or

uncomfortable volume level, since this can cause permanent hearing loss. If you

experience any hearing loss or ringing in the ears, consult a physician.

• Do not rest your weight on the device or place heavy objects on it, and avoid use

excessive force on the buttons, switches or connectors.

Power supply/Power cord

Do not open

Water warning

If you notice any abnormality

Power supply/Power cord

Location

Connections

Handling caution

EMX5016CF Owner’s Manual

Always turn the power off when the device is not in use.

The performance of components with moving contacts, such as switches, volume controls, and connectors, deteriorates over time. Consult qualiﬁed Yamaha service

personnel about replacing defective components.

About this Manual

This manual is divided into two main sections, as follows.

■

Mixer Basics (starts on page 7)

Presents a general explanation of mixers and mixer concepts. Includes a Quick Guide that will help beginners get up to speed very quickly.

■

Reference (starts on page 19)

Provides detailed information about the EMX. Introduces the EMX features, identiﬁes and explains the controls, indicators, and connec-

tors; and explains how to set up the equipment.

* Within this manual, the term “EMX” refers to model EMX5016CF.

* Illustrations herein are for explanatory purposes only, and may not match actual appearance during operation.

* Company names and product names herein are trademarks or registered trademarks of their respective companies.

Speciﬁcations and descriptions in this owner’s manual are for information purposes only. Yamaha Corp. reserves the right to change or modify products or speciﬁcations at any

time without prior notice. Since speciﬁcations, equipment or options may not be the same in every locale, please check with your Yamaha dealer.

XLR-type connectors are wired as follows (IEC60268 standard): pin 1: ground, pin 2: hot (+), and pin 3: cold (-).

Use only Neutrik plugs (NL4) for connecting Speakon connectors.

Insert TRS phone jacks are wired as follows: sleeve: ground, tip:send, and ring:return.

Yamaha cannot be held responsible for damage caused by improper use or modiﬁcations to the device.

Copying of commercially available music or other audio data for purposes other than personal use is strictly prohibited by copyright law. Please respect all

copyrights, and consult with a copyright specialist if you are in doubt about permissible use.

IMPORTANT NOTICE FOR THE UNITED KINGDOM

Connecting the Plug and Cord

WARNING: THIS APPARATUS MUST BE EARTHED

IMPORTANT. The wires in this mains lead are coloured in accordance with the following code:

GREEN-AND-YELLOW : EARTH

BLUE : NEUTRAL

BROWN : LIVE

As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the termi-

nals in your plug proceed as follows:

The wire which is coloured GREEN-and-YELLOW must be connected to the terminal in the plug which is marked by the letter E or by

the safety earth symbol or coloured GREEN or GREEN-and-YELLOW.

The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured BLACK.

The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured RED.

• This applies only to products distributed by Yamaha-Kemble Music (U.K.) Ltd. (3 wires)

1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!

This product, when installed as indicated in the instructions con-

tained in this manual, meets FCC requirements. Modiﬁcations not

expressly approved by Yamaha may void your authority, granted by

the FCC, to use the product.

2. IMPORTANT: When connecting this product to accessories and/

or another product use only high quality shielded cables. Cable/s

supplied with this product MUST be used. Follow all installation

instructions. Failure to follow instructions could void your FCC

authorization to use this product in the USA.

3. NOTE: This product has been tested and found to comply with the

requirements listed in FCC Regulations, Part 15 for Class “B” digi-

tal devices. Compliance with these requirements provides a rea-

sonable level of assurance that your use of this product in a

residential environment will not result in harmful interference with

other electronic devices. This equipment generates/uses radio fre-

quencies and, if not installed and used according to the instruc-

tions found in the users manual, may cause interference harmful to

the operation of other electronic devices. Compliance with FCC

* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA. (class B)

regulations does not guarantee that interference will not occur in

all installations. If this product is found to be the source of interfer-

ence, which can be determined by turning the unit “OFF” and “ON”,

please try to eliminate the problem by using one of the following

measures:

Relocate either this product or the device that is being affected by

the interference.

Utilize power outlets that are on different branch (circuit breaker or

fuse) circuits or install AC line ﬁlter/s.

In the case of radio or TV interference, relocate/reorient the

antenna. If the antenna lead-in is 300 ohm ribbon lead, change the

lead-in to co-axial type cable.

If these corrective measures do not produce satisfactory results,

please contact the local retailer authorized to distribute this type of

product. If you can not locate the appropriate retailer, please con-

tact Yamaha Corporation of America, Electronic Service Division,

6600 Orangethorpe Ave, Buena Park, CA90620

The above statements apply ONLY to those products distributed by

Yamaha Corporation of America or its subsidiaries.

FCC INFORMATION (U.S.A.)

EMX5016CF Owner’s Manual

Thank you for your purchase of this Yamaha EMX5016CF powered mixer. Please read through this

manual carefully before beginning use, so that you will be able to take full advantage of your mixer’s

superlative features and enjoy trouble-free operation for years to come. After reading the manual,

please store it in a safe place.

Features...............................................................................................................................................6

Before Turning On the Mixer................................................................................................................ 6

■

Mixer Basics

Quick Guide ......................................................................................................7

Getting Sound to the Speakers............................................................................................................7

Adding Some Reverb.........................................................................................................................10

Using the Compressors to Enhance Vocals ......................................................................................11

Making the Most of Your Mixer ....................................................................12

A Place for Everything and Everything in its Place ............................................................................12

A Plethora of Connectors—What Goes Where?........................................................................ 12

Balanced, Unbalanced—What’s the Difference?...............................................................................13

How Do Balanced Lines Reject Noise? .............................................................................................13

A balanced cable has three conductors:............................................................................................14

Signal Levels and the Decibel............................................................................................................ 14

Making Better Mixes...........................................................................................................................15

Approaching the Mix—Where Do You Start?.............................................................................15

To EQ or Not to EQ.................................................................................................................... 16

Ambience ...................................................................................................................................17

The Modulation Effects: Phasing, Chorus, and Flanging...........................................................17

Compression..............................................................................................................................18

■

Reference

Front & Rear Panels.......................................................................................19

Controls on Each Channel .................................................................................................................19

Digital Effects Section ........................................................................................................................22

Master Section ...................................................................................................................................23

Rear Panel .........................................................................................................................................28

Speaker Connections ....................................................................................29

2-channel connection.................................................................................................................29

2-channel parallel connection ....................................................................................................29

Setting the GEQ with the FRC function .......................................................30

Rack Mounting ...............................................................................................32

Setup ...............................................................................................................33

Troubleshooting.............................................................................................34

Specifications.................................................................................................35

Contents

EMX5016CF Owner’s Manual

Features

Input Channels ................................................................................................ page 19

The EMX offers 12 monaural mic/line input channels (1 to 15/16) and four stereo input

channel pairs (9/10 to 15/16), allowing you to freely mix inputs from microphones, line-

level devices, and stereo devices. For example, you can mix eight microphones with

four stereo devices, or ten microphones with two stereo synthesizers.

High-Quality Digital Effects............................................................................ page 22

The mixer’s internal effector (two blocks) is in the same league as our SPX effector

series, allowing you to create a rich range of variations with no external help. But of

course you are also free to use the SEND EFF jacks to connect to an external effector

of your choice.

Compressors................................................................................................... page 18

Individual compressors are provided on channels 1 to 8. These let you compress the

dynamic range of input signals such as vocals, guitars and bass, allowing you to bring

down high signal peaks and boost lower level sounds. This feature helps reduce dis-

tortion and allows overall volume to be set higher, resulting in a stronger and more

punchy sound. Moreover, a 3-band compressor is available for applying to the stereo-

bus signal output, which enhances the overall output volume (MAXIMIZE function).

Internal Power Amp ........................................................................................ page 25

The internal amp makes it possible to connect the SPEAKERS jacks directly to non-

powered speakers, with no need for an external ampliﬁer in between. The rear panel

offers two types of speaker connectors: phone jacks and Neutrik Speakon jacks.

Graphic Equalizer and FRC............................................................................ page 30

This 9-band graphic equalizer adjusts the frequency characteristics of the Stereo-bus

signal output. A convenient FRC function (Frequency Response Correction System)

allows you to measure the frequency characteristics of the sound ﬁeld, and automati-

cally adjust the graphic equalizer settings according to the measurement results to

compensate for any sound ﬁeld anomalies.

Feedback Suppressor..................................................................................... page 25

This function automatically checks for and removes feedback.

Before Turning On the Mixer

■

Connecting to Power

Be sure that the POWER switch is in the OFF position.

Connect the included power cord to the AC IN connector on the rear panel.

Plug the power cord into a standard power outlet.

■

Turning the Unit On and Off

NOTE

•To prevent an unpleasant burst of noise from the speakers, you should power up the sound sources ﬁrst, and then the other devices in order of their

distance from the source (starting with the closest).

For example:

Sound source (external device)

→

EMX unit

→

Amps (Powered speakers)

When turning power off, proceed in the opposite order.

• Before turning power on, make sure that the channel faders, ST master fader, AUX1/2 faders, ST SUB OUT control are all the way down.

• Rapidly turning the unit ON and OFF in succession can cause it to malfunction. After turning the unit OFF, wait for about 10 seconds before turning it

ON again.

Push the POWER switch in to turn the power ON.

The model name “EMX5016CF” is shown in the GEQ display. To turn the power off, push the POWER switch again,

so that the indication goes off.

EMX5016CF Owner’s Manual

Mixer Basics

Quick Guide

We begin by connecting up two speakers and generating some stereo output. Note that opera-

tions and procedures will vary somewhat according to the input devices you are using.

Connect up the speakers and your input devices

(microphones, instruments, etc.).

Use non-powered speakers and dedicated speaker cable. Connect

one speaker to SPEAKERS jack A (A1 or A2), and the other to jack B

(B1 or B2). Then connect your input devices (microphones, guitar,

etc.) to the appropriate input jacks on the top panel. For details, see

page 33.

NOTE

We recommend that you avoid connecting electric instruments (such as elec-

tric guitars and basses) directly to the EMX. Instead, these instruments

should be connected through an intermediary device such as a direct box, a

preamp (guitar amp), or an amp simulator.

Getting Sound to the Speakers

Input jacks

SPEAKERS jacks

WRONG!!

RIGHT

CAUTION

• Before connecting input devices to the EMX, be sure that all of these

devices (including microphones) are powered off. And before turning

the power to any device on or off, be sure to turn the volume of that

device all the way down.

• Never connect both A and B jacks to a single speaker. Connection of

both jacks to the same speaker may result in damage to the mixer.

Mixer Basics

EMX5016CF Owner’s Manual

Quick Guide

Mixer Basics

Turn the Channel faders and the ST Master fader all

the way down.

Set the POWER AMP switch to its upper position (to

L-R).

For information about this switch, see page 25.

If you have connected input devices to channels 1

to 8, set the [26dB] switch ON ( ) or OFF ( ) on

each channel accordingly.

If you have connected a line-level device, such as a keyboard or

audio device, set the channel’s switch to the ON ( ). If you have

connected a microphone or other mic-level device, set the switch to

the OFF ( ).

If you are using one or more condenser micro-

phones for your inputs, set the PHANTOM switch to

the ON position ( ).

[26dB] switches

POWER switch

GAIN controls

ON switches

PEAK indicators

Channel faders

POWER AMP switch

PHANTOM switch

ST Master fader

CAUTION

• Be sure to leave this switch off if you do not need phantom power.

• When using phantom power, do not connect any devices other than

condenser microphones to the XLR input jacks. Other devices may be

damaged if connected to phantom power. This precaution does not

apply to balanced dynamic microphones, however, as these will not be

affected by phantom power.

• To protect your speakers and ears: Before turning the PHANTOM

switch ON or OFF, be sure to turn off the power to the mixer and to all

other devices having internal ampliﬁers. We also recommend that you

turn all output controls (Channel faders, ST Master fader, etc.) to mini-

mum settings before operating the switch, to avoid risk of loud noises

that could cause hearing loss or device damage.

Quick Guide

Mixer Basics

EMX5016CF Owner’s Manual

Turn on the power.

First turn on the power to all connected devices other than powered

speakers and amp, and then turn on the EMX itself. If using powered

speakers or amps, turn these on last.

NOTE

To prevent an unpleasant burst of noise from the speakers, you should power

up the sound sources ﬁrst, and then the other devices in order of their dis-

tance from the source (starting with the closest).

For example: Sound source (external device)

→

EMX unit

→

Amps (Pow-

ered speakers)

Adjust the GAIN control for each channel you are

using so that the PEAK indicator comes on only at

about maximum input level.

NOTE

To use the LEVEL meter to get an accurate reading of the incoming signal

level: Set the ST/AFL-PFL switch to AFL-PFL( ) and turn on the PFL

switch for each channel you are using. Adjust the GAIN controls so that

LEVEL meter indication occasionally rises above the

“” (0) level. Note that

the PHONES jack outputs the pre-faded signal from all channels whose PFL

switch is ON, so that you can monitor these signals through the headphones.

Turn the ON switch on.

Set the ST Master fader to the “0” position.

Adjust the channel faders on all occupied channels.

Adjust the faders while listening to the output from the speakers.

NOTE

• To use the LEVEL meter to view the level being input to the internal amp:

Set the ST/AFL-PFL switch to ST( ).

• Use the LIMITER lamps to check for clipping of the signal from the SPEAK-

ERS jacks. Note that the LIMITER lamps will come on earlier than the level

meter's PEAK indicators come on.

11 Adjust the overall volume of the ST Master fader.

CAUTION

It is acceptable for the LIMITER lamps to ﬂash on brieﬂy at times, but if

they remain lit continuously then there is risk of damage to your speakers

or to the internal amp. Reduce the ST master fader setting so that these

lamps do not stay on.

EMX5016CF Owner’s Manual

Quick Guide

Mixer Basics

You can use the reverb effect to simulate the sound of a concert hall or jazz club.

1 Turn the EFFECT1 PROGRAM dial to select the desired effect type.

To select a reverb effect, turn the dial to any value from 1 to 5.

2 To turn on the effector, set the EFF1 ON switch

to its ON position ( ).

The switch lights up when turned on. As an alternative to the ON

switch, you can use a separately sold FC5 foot switch to toggle the

effector on and off.

3 Set the EFF1 RTN fader to the “0” position.

4 Use the channel EFF1 knobs to adjust the effect

depth for each channel.

5 Use the EFF1 RTN fader to adjust the overall

effect depth.

Note that you can use the PARAMETER knob to adjust the charac-

teristic sound of the selected effect. If you have selected a reverb

effect, the knob adjusts the reverb time.

HALL 1

SMALL STAGE 1

CHORUS

TREMOLO

ROOM 1

VOCAL ECHO

EARLY REF.

SINGLE DELAY

PLATE 1

KARAOKE

GATE REVERB

DYNA FILTER

LARGE STAGE 1

DELAY

REVERSE GATE

PITCH CHANGE

Adding Some Reverb

EFF1 knobs

PROGRAM dial

EFF1 ON switch

EFF1 RTN fader

Quick Guide

Mixer Basics

EMX5016CF Owner’s Manual

The compressor evens out the input level, reducing the level of loud passages and bringing up

softer passages. The result is a cleaner sound where nuances remain audible and the lyrics are

easier to hear.

1 Adjust the COMP knobs on the relevant channels.

Turn the knob clockwise to increase the compression. Avoid setting the value too high, as too much compres-

sion may result in howling. For more information about the compressors, see page 18.

Using the Compressors to Enhance Vocals

COMP knobs

EMX5016CF Owner’s Manual

Mixer Basics

Making the Most of Your Mixer

An Introduction

A Place for Everything and Everything in its Place

A Plethora of Connectors—What Goes Where?

Questions you’re likely to encounter when setting up a system for the first time might include “Why all these

different types of connectors on the back of my mixer?” and “What’s the difference?”.

Let’s start by taking a look at the most common connector types.

The Venerable RCA Pin Jack

This is the “consumer connector,” and the one that has been most

commonly used on home audio gear for many years. Also known as

“phono” jacks (short for “phonogram”), but the term isn’t used much

these days—besides, it’s too easily confusable with “phone” jacks,

below. RCA pin jacks are always unbalanced, and generally carry a line-

level signal at –10 dB, nominal. You’re most likely to use this type of

connector when connecting a CD player or other home audio type

source to your mixer, or when connecting the output of your mixer to a

cassette recorder or similar gear.

The Versatile Phone Jack

The name “phone jack” arose simply because this configuration was first

used in telephone switchboards. Phone jacks can be tricky because you

can’t always tell what type of signal they’re designed to handle just by

looking at them. It could be unbalanced mono, unbalanced stereo,

balanced mono, or an insert patch point. The connector’s label will

usually tell you what type of signal it handles, as will the owner’s manual

(you do keep your manuals in a safe place, don’t you?). A phone jack

that is set up to handle balanced signals is also often referred to as a

“TRS” phone jack. “TRS” stands for Tip-Ring-Sleeve, which describes

the configuration of the phone plug used.

The Sturdy XLR

This type of connector is generally referred to as “XLR-type,” and almost

always carries a balanced signal. If the corresponding circuitry is

designed properly, however, XLR-type connectors will also handle

unbalanced signals with no problem. Microphone cables usually have

this type of connector, as do the inputs and outputs of most professional

audio gear.

You’ve got yourself a mixer and now you’re ready to use it.

Just plug everything in, twiddle the controls, and away you go … right?

Well, if you’ve done this before you won’t have any problems, but if this is the first time

you’ve ever used a mixer you might want to read through this little tutorial and pick up a

few basics that will help you get better performance and make better mixes.

Stereo/TRS phone plug

Mono phone plug

Sleeve

Ring

Tip

Male

Female

Making the Most of Your Mixer

EMX5016CF Owner’s Manual

Mixer Basics

Balanced, Unbalanced—What’s the Difference?

In a word: “noise.” The whole point of balanced lines is noise

rejection, and it’s something they’re very good at. Any length of wire

will act as an antenna to pick up the random electromagnetic

radiation we’re constantly surrounded by: radio and TV signals as

well as spurious electromagnetic noise generated by power lines,

motors, electric appliances, computer monitors, and a variety of other

sources. The longer the wire, the more noise it is likely to pick up.

That’s why balanced lines are the best choice for long cable runs. If

your “studio” is basically confined to your desktop and all connections

are no more than a meter or two in length, then unbalanced lines are

fine—unless you’re surrounded by extremely high levels of

electromagnetic noise. Another place balanced lines are almost

always used is in microphone cables. The reason for this is that the

output signal from most microphones is very small, so even a tiny

amount of noise will be relatively large, and will be amplified to an

alarming degree in the mixer’s high-gain head amplifier.

How Do Balanced Lines Reject Noise?

** Skip this section if technical details make you queasy. **

Balanced lines work on the principle of “phase cancellation”: if you add two identical signals out of phase (i.e.

one signal is inverted so its peaks coincide with the troughs in the other signal), the result is … nothing. A flat

line. The signals cancel each other out.

While the desired audio signals in the hot and cold conductors are out of phase, any noise induced in the line

will be exactly the same in both conductors, and thus in phase. The trick is that the phase of one signal is

reversed at the receiving end of the line so that the desired audio signals become in-phase, and the induced

noise suddenly finds itself out of phase. The out-of-phase noise signal is effectively canceled while the audio

signal is left intact. Clever, eh?

To summarize

Microphones: Use balanced lines.

Short line-level

runs:

Unbalanced lines

are fine if you’re in a

relatively noise-free

environment.

Long line-level

runs:

The ambient

electromagnetic

noise level will be

the ultimate

deciding factor, but

balanced is best.

Hot (+)

Cold (–)

Ground

Balanced noise cancellation

Unbalanced noise

Noise

Source Cable Receiving device

Source Cable

Phase

inversion

Noise

Noise-free

signal

Phase

inversion

Receiving device

Noise cancelled

EMX5016CF Owner’s Manual

Making the Most of Your Mixer

Mixer Basics

A balanced cable has three conductors:

1) A ground conductor which carries no signal, just the “ground” or “0”

reference against which the signal in the other conductors fluctuates.

2) A “hot” or “+” conductor which carries the normal-phase audio signal.

3) A “cold” or “–” conductor which carries the reverse-phase audio signal.

Signal Levels and the Decibel

Let’s take a look at one of the most commonly used units in audio: the decibel (dB). If the smallest sound that

can be heard by the human ear is given an arbitrary value of 1, then the loudest sound that can be heard is

approximately 1,000,000 (one million) times louder. That’s too many digits to deal with for practical calculations,

and so the more appropriate “decibel” (dB) unit was created for sound-related measurements. In this system

the difference between the softest and loudest sounds that can be heard is 120 dB. This is a non-linear scale,

and a difference of 3 dB actually results in a doubling or halving of the loudness.

You might encounter a number of different varieties of the dB: dBu, dBV, dBM and others, but the dBu is the

basic decibel unit. In the case of dBu, “0 dBu” is specified as a signal level of 0.775 volts. For example, if a

microphone’s output level is –40 dBu (0.00775 V), then to raise that level to 0 dBu (0.775 V) in the mixer’s

preamp stage requires that the signal be amplified by 100 times.

A mixer may be required to handle signals at a wide range of levels, and it is necessary match input and output

levels as closely as possible. In most cases the “nominal” level for a mixer’s input and outputs is marked on the

panel or listed in the owner’s manual.

Hot

Cold

Shield

(Ground)

Outer

Insulation

Balanced Unbalanced

+ 20 dBu

0 dBu

0.775 V

20 dBu

40 dBu

60 dBu

The inputs and outputs on home-use audio gear

usually have a nominal level of –10 dBu.

Most professional mixers, power amplifiers, and other

types of equipment have inputs and outputs with a

nominal level of +4 dBu.

Microphone signal levels vary over a wide range

depending on the type of microphone and the source.

Average speech is about –30 dBu, but the twittering of

a bird might be lower than –50 dBu while a solid bass

drum beat might produce a level as high as 0 dBu.

Making the Most of Your Mixer

EMX5016CF Owner’s Manual

Mixer Basics

Making Better Mixes

Approaching the Mix—Where Do You Start?

Mixing is easy, right? Just move the faders around until it sounds right? Well, you can do it that way, but a more

systematic approach that is suited to the material you’re mixing will produce much better results, and faster.

There are no rules, and you’ll probably end up developing a system that works best for you. But the key is to

develop a system rather than working haphazardly. Here are a few ideas to get you started:

Faders Down

It might sound overly simple, but it is usually a good idea to start with all channel faders off—all the way down.

It’s also possible to start with all faders at their nominal settings, but it’s too easy to lose perspective with this

approach. Start with all faders down, then bring them up one by one to fill out the mix. But which channel

should you start with?

Example1: Vocal Ballad Backed by Piano Trio

What are you mixing? Is it a song in which the vocals are the most

important element?

If so you might want to build the mix around the vocals. This means

bringing the vocal channel up to nominal first (if your level setup

procedure has been done properly this will be a good starting point),

and then adding the other instruments.

What you add next will depend on the type of material you are

working with and your approach to it. If the vocals are backed by a

piano trio and the song is a ballad, for example, you might want to

bring in the piano next and get the vocal/piano relationship just right,

then bring in the bass and drums to support the overall sound.

Example2: Funky R&B Groove

The approach will be totally different if you’re mixing a funky R&B

number that centers on the groove. In this case most engineers will

start with the drums, and then add the bass. The relationship between

the drums and bass is extremely important to achieve the “drive” or

groove the music rides on. Pay particular attention to how the bass

works with the kick (bass drum).

They should almost sound like a single instrument—with the kick

supplying the punch and the bass supplying the pitch. Once again,

there are no rules, but these are concepts that have been proven to

work well.

EMX5016CF Owner’s Manual

Making the Most of Your Mixer

Mixer Basics

To EQ or Not to EQ

In general: less is better. There are many situations in which you’ll need to cut certain frequency ranges, but

use boost sparingly, and with caution. Proper use of EQ can eliminate interference between instruments in a

mix and give the overall sound better definition. Bad EQ—and most commonly bad boost—just sounds terrible.

Cut for a Cleaner Mix

For example: cymbals have a lot of energy in

the mid and low frequency ranges that you

don’t really perceive as musical sound, but

which can interfere with the clarity of other

instruments in these ranges. You can basically

turn the low EQ on cymbal channels all the

way down without changing the way they

sound in the mix. You’ll hear the difference,

however, in the way the mix sounds more

“spacious,” and instruments in the lower

ranges will have better definition. Surprisingly

enough, piano also has an incredibly powerful

low end that can benefit from a bit of low-

frequency roll-off to let other instruments—

notably drums and bass—do their jobs more

effectively. Naturally you won’t want to do this if

the piano is playing solo.

The reverse applies to kick drums and bass guitars: you can often roll off the high end to create more space in

the mix without compromising the character of the instruments. You’ll have to use your ears, though, because

each instrument is different and sometimes you’ll want the “snap” of a bass guitar, for example, to come

through.

Boost with Caution

If you’re trying to create special or unusual

effects, go ahead and boost away as much as

you like. But if you’re just trying to achieve a

good-sounding mix, boost only in very small

increments. A tiny boost in the midrange can

give vocals more presence, or a touch of high

boost can give certain instruments more “air.”

Listen, and if things don’t sound clear and

clean try using cut to remove frequencies that

are cluttering up the mix rather than trying to

boost the mix into clarity.

One of the biggest problems with too much

boost is that it adds gain to the signal,

increasing noise and potentially overloading

the subsequent circuitry.

Some Frequency Facts

The lowest and highest frequencies than can be heard by the human ear are generally considered to be around 20 Hz

and 20,000 Hz, respectively. Average conversation occurs in the range from about 300 Hz to about 3,000 Hz. The

frequency of a standard pitchfork used to tune guitars and other instruments is 440 Hz (this corresponds to the “A3”

key on a piano tuned to concert pitch). Double this frequency to 880 Hz and you have a pitch one octave higher (i.e.

“A4” on the piano keyboard). In the same way you can halve the frequency to 220 Hz to produce “A2” an octave lower.

20 50 100 200 500 1 k 2 k 5 k 10 k 20 k

(

)

Piano

Bass Drum

Snare Drum

Bass

Guitar

Trombone

Trumpet

Cymba

Fundamental: The frequency that determines the basic musical pitch.

The fundamental and harmonic frequency ranges of some

musical instruments.

Harmonics: Multiples of the fundamental frequency that play a role

in determining the timbre of the instrument.

Signal

Level (dB)

Frequency (Hz)

LOW Boost

LOW Flat

LOW Cut

MID Boost

MID Flat

HIGH Boost

HIGH Flat

HIGH Cut

MID Cut

Making the Most of Your Mixer

EMX5016CF Owner’s Manual

Mixer Basics

Ambience

Your mixes can be further refined by adding

ambience effects such as reverb or delay. On the

EMX mixers these effects are built in. The internal

DSP (Digital Signal Processor) can be used to add

reverb or delay to individual channels in the same

way as external effects processors, with the extra

connections required by, or the loss in sound quality

often caused by external processing. (Refer to

page 22).

You need to be careful not to overdo effects,

however, because going to far can undermine the

clarity and quality of your mix. Use your ambience

effects just enough to create the required feeling of

depth, but no more than is necessary to keep your

sound clean.

Reverb and Delay Time

A variety of reverb and delay effect programs are

provided, and nearly all of then have a reverb/delay

time parameter than can be adjusted via the panel

PARAMETER control.

Small adjustments to the reverb/delay time can

actually have a significant effect on the sound. The

optimum reverb time for a piece of music will depend

on the music’s demo and density, but as a general

rule longer reverb times are good for ballads, while

shorter reverb times are more suited to up-tempo

tunes. Delay times can be adjusted to create a wide

variety of “grooves”, and you need to select the time

that best suits the music. When adding delay to a

vocal, for example, try setting the delay time to

dotted eighth notes corresponding to the tune’s

tempo.

Reverb Tone

Different reverb programs will have different “reverb

tone” due to differences in the reverb time of the high

or low frequencies, or differences in the overall

frequency response of the reverb sound. Always be

careful not apply too much reverb, particularly in the

high frequencies. In addition to resulting in unnatural

sound, excessive high-frequency reverb can interfere

with the high frequencies in other parts of the mix. If

you can hear more reverb than direct sound in the

upper frequency range, try selecting a different effect

program. It’s always a good idea to choose a reverb

program that gives you the depth you want without

detracting from the clarity of the mix.

Reverb Level

It’s amazing how quickly your ears can lose

perspective and fool you into believing that a totally

washed-out mix sounds perfectly fine. To avoid

falling into this trap start with reverb level all the way

down, then gradually bring the reverb into the mix

until you can just hear the difference. Any more than

this normally becomes a “special effect.” You don’t

want reverb to dominate the mix unless you are

trying to create the effect of a band in a cave—which

is a perfectly legitimate creative goal if that’s the sort

of thing you’re aiming for.

The Modulation Effects: Phasing,

Chorus, and Flanging

All of these effects work on basically the same

principle: a portion of the audio signal is “time-

shifted” and then mixed back with the direct signal.

The amount of time shift is controlled, or

“modulated”, by an LFO (Low-frequency Oscillator).

When we say “time shift,” however, we’re not talking

in terms of minutes or even seconds.

For phasing effects the shift is very small indeed – a

difference measured in degrees of phase shift rather

than time units. The phase difference between the

modulated and direct signals causes cancellation at

some frequencies and reinforces the signal at others

– a “comb filter” effect – and this causes the

shimmering sound we hear. Phasing is the subtlest

of all these effects, producing a gentle shimmer that

can add life to a wide range of sources without being

too obtrusive.

For chorus and flanging the signal is actually delayed

by several milliseconds (a millisecond is a

thousandth of a second), with the delay time

modulated by an LFO, and recombined with the

direct signal. In addition to the comb-filter effect

described above, the delay modulation in these

effects causes a perceived pitch shift which, when

mixed with the direct signal, results in a harmonically

rich swirling or swishing sound. The difference

between chorus and flanging effects is primarily in

the amount of delay time and feedback used –

flanging uses longer delay times than chorus,

whereas chorus generally uses a more complex

delay structure. Chorus is most often used to thicken

the sound of an instrument, while flanging is usually

used as an outright “special effect” to produce other-

worldly sonic swoops.

EMX5016CF Owner’s Manual

Making the Most of Your Mixer

Mixer Basics

Compression

Have you ever wondered why professionally produced recordings sound so different from your own? There are

numerous reasons, of course, but one important factor is the judicious use of compression.

One form of compression known as “limiting” can,

when properly used, produce a smooth, unified

sound with no excessive peaks or distortion.

Compression can also be used within a mix to

make a voice or instrument seem to come

forward, or simply to even out level differences.

Compression can be used to make a mix seem

bigger and louder by producing a more “saturated”

sound. Professional compressors have numerous

parameters that need to be carefully adjusted:

attack, release, threshold, level, and sometimes

more. A professional sound engineer might need

to spend a considerable amount of time, based on

a considerable amount of experience, to set each

of these parameters to achieve the desired sound.

The EMX compressor makes achieving great

sound much easier. All you need to do is set a

single “compression” control and all of the pertinent

parameters are automatically adjusted for you.

The engineers who designed this fine compressor paid careful attention to achieving the best sound quality

possible so that you can quickly achieve pro-quality compression without having to worry about a confusing

multitude of settings.

A common example of the use of compression is to “tame” a vocal that has a wide dynamic range in order to

tighten up the mix. With the right amount of compression you’ll be able to clearly hear whispered passages

while passionate shouts are still well balanced in the mix. Compression can also be valuable on bass guitar,

producing a smooth bass sound that stays solid through the tune. Compression can also be applied to guitar

tracks to add extra sustain. Too much compression can be a cause of feedback, however, so use it sparingly.

Music First—Then Mix

In any case, the music comes first. Think about the music and let it guide the mix, rather than trying to do things

the other way around. What is the music saying and what instrument or technique is being used to drive the

message? That’s where the focus of your mix should be. You’re using a high-tech tool to do the mixing, but the

mix itself is as much art as the music. Approach it that way and your mixes will become a vital part of the music.

OUTPUT

INPUT

(Min)

(Max)

EMX5016CF Owner’s Manual

Reference

Front & Rear Panels

Controls on Each Channel

1 INPUT A and INPUT B Jacks (Channels 1

to 8)

You can connect an input source to either jack. Be sure

to set the [26 dB] switch 4 to match the type of device

you are connecting.

INPUT A: A balanced XLR-type microphone input

jack (1:Ground; 2:Hot; 3:Cold).

If you are connecting a condenser micro-

phone, be sure to turn the PHANTOM

switch c to its ON position.

INPUT B: A TRS phone-type balanced line input

jack (T: hot, R: cold, S: ground). Accepts

both balanced and unbalanced line input.

When using phantom power, do not connect any

devices other than condenser microphones to the

XLR input jacks. Other devices may be damaged if

connected to phantom power. This precaution does

not apply to balanced dynamic microphones, how-

ever, as these will not be affected by phantom power.

On any given channel, you may use either INPUT A

or INPUT B, but not both. Please connect to only

either of these jacks on each channel.

2 LINE/MIC Jacks (Channels 9/10 to 15/16)

These jacks accept stereo inputs and mic inputs. Use

these to connect up stereo output devices, such as ste-

reo synthesizers and CD players, and microphones.

LINE jacks: Unbalanced stereo inputs. Each channel

pair have phone jacks and RCA pin

jacks.

MIC jack: XLR balanced mic-level input jack. If

you are connecting a condenser micro-

phone, be sure to turn the PHANTOM

switch c to its ON position.

When using phantom power, do not connect any

devices other than condenser microphones to the

XLR input jacks. Other devices may be damaged if

connected to phantom power. This precaution does

not apply to balanced dynamic microphones, how-

ever, as these will not be affected by phantom power.

If you wish, you may use the channel pair’s LINE and

MIC jacks together at the same time. But note that the

levels cannot be adjusted independently.

Channels

9/10 to 15/16

(Stereo)

Channels

1 to 8

(Monaural)

Cold (–)

Ground Hot (+)

R: Cold (–)

S: Ground T: Hot (+)

CAUTION

NOTE

CAUTION

NOTE

Reference

EMX5016CF Owner’s Manual

Front & Rear Panels

Reference

3 INSERT I/O Jack (Channels 1 to 8)

Each of these jacks is positioned between the equalizer

and fader of the corresponding input channel (1 to 8).

You can use these jacks to connect channels to devices

such as graphic equalizers, compressors, and noise ﬁl-

ters. These are TRS (tip, ring, sleeve) phone jacks that

support bidirectional operation.

Connection to an INSERT I/O jack requires a special

separately-sold insertion cable—such as the Yamaha

YIC025, YIC050, or YIC070—as shown below.

4 [26 dB] Switch (Channels 1 to 8)

Pressing this button turns on the attenuator for each

channel, attenuating the input signal level by 26 dB.

If you have connected a line-level device, such as a

keyboard or audio device, set the channel’s switch to

ON ( ). If you have connected a microphone or

other mic-level device, set the switch to OFF ( ).

5 GAIN Control

Adjusts the gain applied to the input signal level. To

get the best balance between the S/N ratio and the

dynamic range, adjust the gain so that the PEAK indi-

cator D comes on only at about maximum input level.

The –60 to –16 scale indicates the MIC input adjust-

ment level. The –34 to 10 scale indicates the LINE

input adjustment level.

6 (High Pass Filter) Switch

Switches the high pass ﬁlter on/off. To turn the HPF

on, press this switch in. The HPF cuts frequencies

below 80 Hz. (But note that regardless of the switch

setting, the mixer does not apply this HPF to the line

inputs of stereo input channels.)

7 COMP knob (Channels 1 to 8)

This knob adjusts the level of compression applied to

the channel. As the knob is turned to the right, the

mixer automatically raises the compression ratio while

adjusting the output gain accordingly. The result is a

narrower, more even dynamic range, as louder signals

are softened while the overall level is boosted. Avoid

setting the knob too high, however, as excess compres-

sion may lead to howling.

G G

9 9

0 0

Channels

9/10 to 15/16

(Stereo)

Channels

1 to 8

(Monaural)

NOTE

To the input jack of the

external processor

To the output jack of the

external processor

Sleeve (Ground)

Tip:OUT

Tip:IN

To the INSERT I/O jack

Sleeve (Ground)

Ring :IN

Tip:OUT

Sidan laddas ...

Yamaha EMX 5016CF Användarmanual

varumärke: Yamaha

Modell: EMX 5016CF

Kategori: Ljudmixer

Typ: Användarmanual

Denna manual är också lämplig för

EMX5016CF

Ladda ner pdf

Rapportera

på andra språk

italiano: Yamaha EMX 5016CF Manuale utente
čeština: Yamaha EMX 5016CF Uživatelský manuál
español: Yamaha EMX 5016CF Manual de usuario
Deutsch: Yamaha EMX 5016CF Benutzerhandbuch
polski: Yamaha EMX 5016CF Instrukcja obsługi
português: Yamaha EMX 5016CF Manual do usuário
français: Yamaha EMX 5016CF Manuel utilisateur
Türkçe: Yamaha EMX 5016CF Kullanım kılavuzu
English: Yamaha EMX 5016CF User manual
dansk: Yamaha EMX 5016CF Brugermanual
русский: Yamaha EMX 5016CF Руководство пользователя
suomi: Yamaha EMX 5016CF Ohjekirja
Nederlands: Yamaha EMX 5016CF Handleiding
română: Yamaha EMX 5016CF Manual de utilizare

Relaterade papper

Andra dokument

Allied Telesis AT-9924T/4SP-A-20 Installationsguide