Witt C9600 Bruksanvisning

C77.JM7.Wittⓓ.1-160408M

KUVINGS

WHOLE SLOW JUICER

MANUAL

• After you read this manual,

keep in the place you can reach easily.

• The color of product may vary.

•

Household use only.

EN

DK

NO

SE

FI

C9600

M7

CONTENTS

Important Safeguards

Safety Warning

Parts

How to Assemble

How to Operate

Tips on Operation

Tips on Ingredients

Ingredient Preparation

How to Disassemble and Clean

How to Clean Silicone Parts

OPTIONAL | How to Use the Cleaning Tool

Troubleshooting Q&A

Specications

Guarantee

04

06

08

10

12

14

15

16

20

22

23

24

26

27

English

Danish

Read all Instructions Before Use.

Læs venligst hele brugsanvisningen inden ibrugtagning.

30

34

36

38

40

41

42

46

48

49

50

52

53

Sikkerhedsanvisninger

Dele

Samleanvisning

Brugsanvisning

Gode råd vedr. drift

Gode råd vedr. ingredienser

Ingrediensforberedelse

Kuvings skilles ad og rengøres

Rengøring af silikonedele

Brug af rengøringsværktøjet

Problemløsning

Specikationer

Garanti

Läs noggrant igenom bruksanvisningen innan

Kuvings-produkten används.

Säkerhetsföreskrifter

Delar

Monteringsanvisningar

Bruksanvisning

Tips om drift

Tips om ingredienser

Ingrediensförberedelse

Ta isär och rengöra Kuvings

Rengöra silikondelar

Använda rengöringsverktyget

Felsökning

Tekniska data

Garanti

84

86

88

90

92

93

94

98

100

101

102

104

105

Swedish

Sikkerhetsanvisninger

Deler

Monteringsanvisning

Bruksanvisning

Gode råd vedr. drift

Gode råd vedr. ingredienser

Forberedelse av ingredienser

Kuvings tas fra hverandre og rengjøres

Rengjøring av silikondeler

Bruke rengjøringsverktøyet

Problemløsning

Spesikasjoner

Garanti

56

60

62

64

66

67

68

72

74

75

76

78

79

Norwegian

Les hele bruksanvisningen nøye før du tar Kuvings i bruk.

Turvallisuusohjeet

Osat

Asennusohjeet

Käyttöohjeet

Vinkkejä koneen käyttöön

Vinkkejä raaka-aineisiin

Ainesten esivalmistelu

Kuvingsin purkaminen ja puhdistus

Silikoniosien puhdistus

Puhdistustyökalun käyttö

Ongelmanratkaisu

Tuotetiedot

Takuu

108

112

114

116

118

119

120

124

126

127

128

130

131

Finnish

Lue koko käyttöopas huolellisesti läpi ennen laitteen käyttöönottoa.

EN

DK

NO

SE

FI

EN

DK

NO

SE

FI

04 05

ㆍ This appliance is for household use only. Please carefully follow the instructions

in the manual.

(The appliance cannot be covered under the manufacture warranty if the product is

abnormally or commercially used.)

ㆍSave the instruction manual for future reference

ㆍ

If the appliance is given away as a gift, please include the manual with the product.

ㆍThese instruction shall also be available in an alternative format.

e.g on a website. www.kuvings.com

Read all instructions.

To protect against risk of electrical shock do not put motor or base of

unit in water or other liquid.

Children should be supervised to ensure that they do not play with the

appliance.

Unplug from outlet when not in use, before putting on or taking o parts,

and before cleaning.

Avoid contacting moving parts.

If the supply cord is damaged, it must be replaced by the manufacturer,

its service agent or similarly qualied persons in order to avoid a hazard.

The use of attachments not recommended or sold by the manufacturer

may cause re, electric shock or injury.

Do not use outdoors.

Do not let cord hang over edge of table or counter.

Always make sure juicer cover is clamped securely in place before motor is

turned on. Do not unfasten clamps while juicer is in operation.

Be sure to turn switch to OFF position after each use of your juicer.

Make sure the motor stops completely before disassembling.

Do not put your ngers or other objects into the juicer opening while it

is in operation. If food becomes lodged in opening, use food pusher or

another piece of fruit or vegetable to push it down. When this method is

not possible turn the motor o and disassemble juicer to remove the

remaining food.

Do not use the appliance if the rotating sieve is damaged.

When a separable pulp container is provided, do not operate without

the pulp container in place.

Please do not alter the appliance in anyway.

1.

2.

3.

4.

5.

6.

7.

8.

9.

10.

11.

12.

13.

14.

15.

Do not use the appliance for anything other than it's intended purpose

as described in the manual.

The appliance should be used for limited period of time.

This appliance can be used by children age from 8 years and above and

persons with reduced physical, sensory or mental capabilities or lack of

experience and knowledge if they been given supervision of instruction

concerning use of the appliance in a safe way and understand the hazards

involved. Children shall not play with the appliance. Cleaning and user

maintenance shall not be made by children without supervision.

This appliance is not intended for use by persons(including children) with

reduced physical, sensory or mental capabilities, or lack of experience and

knowledge, unless they have been given supervision of instruction

concerning use of the appliance by a person responsible for their safety.

16.

17.

18.

19.

When using electrical appliances, basic safety precautions

should always be followed including the following:

EN

06 07

The following precaution is provided to ensure the safety of the user. Please carefully read

through the precautions and exercise a degree of care when using the appliance.

Warning : Warns risk of death of severe injuries.

Caution : Warns risk of injuries or appliance damage.

Prohibited

Follow instruction

Unplug from the outlet

Do not disassemble

Must take action

Be cautious of electric shock

SAFETY WARNING SAFETY WARNING

Do not repair, disassemble the base, or customize the appliance.

→ The appliance may not operate properly causing re,

electrical shock or injury.

Do not put the parts in the dishwasher or extremely hot water.

→The parts may wear faster.

Do not use the appliance on an uneven surface.

→It may cause a malfunction if the appliance tips over.

To protect the power cord, please do not aggressively bend or put

heavy object on top of the power cord.

→It may cause short circuit or even re.

Keep away from children and store the appliance in a safe place.

→It may cause injury.

Please do not store or operate the appliance near any heating

appliance.

→ The appliance may become discolored or deformed.

Do not use any hazardous chemical to clean the appliance or

ammable sprays near the appliance.

→It may change the color of the appliance or could result in a re.

Do not plug multiple power cords on a single outlet during operation.

→ It may cause an explosion or re.

Do not touch the power cord with wet hands.

→ It may cause electrical shock.

Use a dry towel to clean the power cord if it is dirty or wet.

→It may cause electrical shock or re.

Do not drop the appliance nor inict strong force to the appliance.

→It may damage or break the appliance.

Do not unplug by pulling o the power cord cable.

→It may damage the power cord and cause electrical shock.

Do not put your nger or other objects into the feeding tube while it

is in operation.

→It may cause injury.

Do not leave the appliance unattended. Unplug the power cord from

the outlet when not in use.

Operating the juicer without ingredients can cause damage to the

screw.

EN

0908

PARTS

2. Drum Lid

3. Juicing Bowl

4. Pulp Cup 7. Juice Cup

5. Smart Cap

6. Base

1. Feeding Tube

10. Juicing Screw

13. Rotating Brush

9. Strainer

11. Pusher

8. Rotation Wiper

12. Cleaning Brush

Align the red dots ● on each part and

assemble in the order shown. Once

assembled, turn the drum lid clockwise

to close.

STEP 1

Top-set Assembly

STEP 2

Top-set and base assembly

Place the drum lid on the juicing bowl.

Align the down arrow ▼on the drum lid

with the OPEN mark on the base and

turn to the CLOSE position.

Pusher

Align

Align the dots ●

and slide

the pusher in.

Detachable

+

EN

10 11

HOW TO ASSEMBLE

Assemble the strainer into the rotation

wiper then place this assembly in to the

juicing bowl ensuring the red dot ●on

the strainer is aligned with the red dot ●

on the juicing bowl.

The juicing screw needs to be locked in

place in order to close the drum lid.

Note |

Juicer will not operate if parts are not

assembled properly.

Note |

STEP 1

Top-set Assembly

STEP 2

Top-set and Base Assembly

Place the juicing screw into the strainer.

Turn and press down on it until it clicks

into place.

Place the drum lid on to the juicing bowl

aligning the red dot ● on the drum lid with

the red dot●on the juicing bowl. Turn

clockwise to close, aligning the red dot ●

on the drum lid with the close mark .

Check Before

Operating

• Wash the parts before rst use.

• Ensure that scrapers of rotation wiper and silicone ring of strainer are

assembled properly.

12

3

4

5

Place the pulp cup under the pulp

spout and place the juice cup under the

juice spout as shown in the illustration.

Place the drum lid on the juicing bowl.

Align the down arrow ▼ on the drum

lid with the OPEN mark on the base

and turn to the CLOSE position.

Open

Close

Detachable

Open/Close mark on the top-set.

6

For easy assembly hold the drum lid

by grabbing the feeding tube and turn

clockwise as shown in the illustration.

TIP

EN

12 13

Use the smart cap to make mixed juices,

stop juice from dripping, or rinse between dierent juices.

After juice and pulp are completely extracted, switch the unit OFF.

HOW TO OPERATE

After preparing the ingredients, plug the power cord into a wall outlet.

Press the FWD(FORWARD) button to operate.

Insert the prepared ingredients one piece at a time.

• Do not touch the power cord with wet hands.

It may cause electrical shock, short-circuit, or re.

• Check the safety of the wall outlet.

• FWD(Forward) : Pulls down and slowly masticates the ingredients.

• REV(Reverse) : Pushes the ingredients back up to dislodge them.

• Fibrous leafy vegetables (celery, kale, etc.):

» Separate each stem. Cut the outer stems that are thick and tough to 10 cm long or less.

» Bundle up the leafy vegetables as inserting into the juicer. Alternate between leafy

parts and stems.

• Before extracting, remove hard seeds or pits in ingredients.

• When juicing frozen fruits with small seeds, ensure that even the seeds are completely

thawed.

• Insert the ingredients one piece at a time.

• Align the dots ● and slide the pusher in.

• After inserting ingredients, use the pusher when it is necessary. Too much use of the

pusher may aect the juice quality.

» Intermittently use the pusher for soft ingredients like tomatoes and apples. Constant

use of pusher for soft ingredients may aect the juice quality.

• If the remaining ingredients in the juicing bowl have not been extracted

completely, the drum lid may not open easily. After each extraction, run the juicer

for an additional 30 seconds to let the juicer extract the remaining pulp.

• When the drum lid is stuck, press the REV(REVERSE) - O(OFF) - FWD(FORWARD)

button in this order; switching back and forth 2 or 3 times to dislodge the

ingredients. Then place hands on top of the drum lid and rmly press down while

simultaneously turning the drum lid counter clockwise to open.

» Depending on the ingredients, pour water down the feeding tube to rinse out

the interior of the juicing bowl and then attempt to remove the drum lid.

• Juicing with the smart cap closed creates various mixed juice creations when

dierent fruits and vegetables, milk, banana, beans etc. are selected.

• After juicing, close the smart cap to stop the juice from dripping, especially when

disassembling the juicing bowl o the base.

• When making dierent juices quickly rinse away any leftover avors by running a

glass of water in the juicer with the smart cap closed.

• Leave the smart cap open when juicing ingredients that create excessive foam

during extraction, (e.g. apples, celery).

• Pay close attention when operating with the smart cap closed. Juice may overow

if the juice collected in the juicing bowl exceeds its capacity marked on the bowl.

Note |

Tip |

Note |

Tip |

If the ingredients become jammed in the screw and the drum lid does not open, press the O(OFF)

button. Then press and hold the REV(REVERSE) button until the ingredients become dislodged.

Repeat REV(REVERSE) - O(OFF) - FWD(FORWARD) as often as needed to achieve the desired result.

STEP 1 STEP 3

STEP 4

STEP 5

STEP 2

If the juicer stops during operation:

Switch the button to O(OFF) position then press and

hold the REV(REVERSE) button until the ingredients

become dislodged.

Repeat REV(REVERSE) - O(OFF) - FWD(FORWARD) as

needed.

FWD(FORWARD) : Pulls down the food

O(OFF) : Stops the operation

REV(REVERSE) : Pushes the food back up

▶ ▶ ▶

4

1 3

2

O(OFF) O(OFF)REV(REVERSE) FWD(FORWARD)

Note | · REV(REVERSE) : Pushes the ingredients back up to dislodge them.

The REV(REVERSE) button only works while holding down the switch.

· Switch O(OFF) ensuring that the juicer comes to a complete stop.

Then press REV(REVERSE).

Hold the REV(REVERSE) button for 2-3 seconds and release. Repeat as needed.

Let the juicer stop completely before using the REV(REVERSE) button to prevent malfunction.

· If the juicer does not work after these steps, disassemble and clean the parts before

operating the juicer again.

EN

14 15

TIPS ON OPERATION TIPS ON INGREDIENTS

Peach, nectarines, apricot, plum, mango, etc.

Remove hard seeds from the ingredients

before juicing.

Hard seeds

Pineapple, melon, mango, orange, etc.

Peel the skins from the ingredients before juicing.

Hard or

inedible

skins

Frozen strawberry, blueberry, raspberry, etc.

Completely thaw frozen fruits before juicing.

Do not use ice.

Frozen

fruits or ice

Sesame seed, butter, margarine, etc.

Do not extract ingredients containing vegetable

or animal oil. This can reduce performance and

even damage the juicer.

Vegetable/

animal oil

Coconuts, sugarcane, whole grains are prohibited

due to its brousness and lack of water content.

Others

The Slow Juicer is an innovative product that uses a patented slow-

speed masticating technology to efficiently extract the juice from

ingredients. The juicer is designed to obtain the best result from

ingredients with firm composition and with high water content.

For best result, each ingredient should be prepared and extracted

depending on its characteristics and properties.

Experience the best quality juice by understanding each ingredient’s characteristics

and knowing the optimal way of handling the ingredients.

1. Operating the juicer without ingredients can cause damage to the screw.

2. Do not continuously operate the juicer for more than 30 minutes.

This can damage the motor from overheating.

After continuous use, let the juicer rest for 30 minutes to cool down before starting another

session.

3. Do not put hand, utensil, tong, or other objects into the feeding tube other than the

provided pusher.

4. During operation, do not put spoon, spatula or other objects into the juice spout of

the juicing bowl.

If other object is put into the juice spout during operation, such materials can get stuck and

damage the juicer parts.

5. Do not put dried whole grains, fruits with hard seeds or ice.

These may damage the juicer parts (e.g. juicing bowl, juicing screw, and strainer).

· Beans or grains can be used if soaked overnight or boiled.

(Do not use more than 500g per each session.)

· Fruits with pits and hard seeds (e.g. nectarines, peaches, mangoes and cherries) must be pitted

before juicing.

· When using frozen fruits with small seeds such as grapes, completely thaw before inserting

them into the juicer.

· Use of ice in the juicer will decrease the product durability over time.

6. Do not use ingredients containing excessive amounts of vegetable oil or animal fat.

Do not use the juicer to extract vegetable oil from ingredients.

If vegetable/animal oil gets on the juicing screw, it may reduce performance and even damage

the part.

7. Do not reinsert the extracted pulp into the juicer. This can cause the juicer to stop or

cause the drum lid not to open.

8. After juicing ingredients with seeds like grapes, thoroughly clean all the crevices on

the bottom of the juicing screw.

DO NOT

put the following ingredients into the juicer:

Juicer damage due to owner negligence or from not following the instructions in the owner’s manual will void

the warranty service.

EN

16 17

INGREDIENTS PREPARATION

Hard fruits and

vegetables may put

excess strain onto the

motor and cause it to

stall.

To increase the juice

yield, juice fruits and

vegetables with high

water content.

PREPARATION TIPS:

• If the ingredients such as carrots exceed 2,5 cm in width or 15 cm in lenght please slice them 2,5 cm

wide and 5-15 cm long.

EXTRACTION TIPS:

• Slowly insert the ingredients one at a time.

• Pace the juicing speed ensuring each ingredient is thoroughly extracted.

• To maximize the juice yield, juice with ingredients with high water content.

PREPARATION TIPS:

• Cut 1-4 wedges (if necessary).

EXTRACTION TIPS:

• Slowly insert the ingredients one piece at a time.

• Use the pusher to push the ingredients down the feeding tube. (The pusher also helps prevent juice

from spraying out of the feeding tube when extracting ingredients with high water content)

• Leave the smart cap open when juicing ingredients that create excessive foam during extraction.

(Foam can accumulate if operated with the smart cap closed. )

• It is recommended that the extracted juice be consumed within 48 hours after extracting.

Depending on the density of the ingredients the extracted juice can gradually show layers over time.

• If there is an excessive amount of foam, use a mesh strainer to separate it from the juice.

• When an ingredient is being masticated by the juicing screw, the squeezed ingredient may splash juice

through the feeding tube. Use the pusher to block out the juice splash when juicing

| (E.g. apples, oranges & tomatoes)

Before

Operating: How to Use

the Smart

Cap:

Juice Yield:

Adjusting

the amount

of pulp in

the juice:

• Before Operating: If the juicer is jammed or if the drum lid does not open,

press the REVERSE button and hold until it becomes dislodged.

Repeat REVERSE-OFF-FORWARD as needed.

• Continue operating the juicer until all the ingredients in the juicing bowl are

extracted. The drum lid may not open easily if there is a lot of pulp remaining

in the juicer.

• Every ingredient yields dierent amounts of juice.

• Juicing with the smart cap closed allows mixed juice creations with dierent

fruits, vegetables and liquids.

• After juicing, close the smart cap to block excess juice from dripping,

especially when disassembling the juicing bowl o the base.

• When making dierent juices quickly rinse away any leftover avors by

running a glass of water in the juicer with the smart cap closed.

• Leave the smart cap open when juicing ingredients that create excessive

foam during extraction (e.g. apples, celery).

• Pay close attention when operating the juicer with the smart cap closed. Juice

may overow if the juice collected in the juicing bowl exceeds its capacity

marked on the juicing bowl.

• For the optimal extraction and maximum juice yield, cut the ingredients

following the guidelines given in this section.

• Insert ingredients slowly monitoring how the ingredients are extracted.

The juice yield may vary depending on the juicing speed.

• Depending on the ingredient, you may get extra pulp in the juice when

juicing continuously.

• To reduce the amount of pulp, disassemble the top-set and wash frequently.

Soft fruits and vegetables

(e.g. oranges, tomatoes):

Hard fruits and vegetables

(e.g. carrots, potato, beets):

- Peel the skin o oranges, and for tomatoes and

apples, take out the stem.

- If the ingredients are larger than the feeding

tube, cut the ingredients into pieces that will fit into

the feeding tube.

- Fruits with seeds must be pitted before extraction.

Cut to 1-4 wedges (if necessary) then slowly insert the

ingredients down the feeding tube.

1-4 wedges (if necessary)

15 cm

1,25–2,5 cm

2,5 cm

EN

18 19

If the lid does not open due to excessive amount of small seeds left in the juicing bowl,

continuously run the juicer for 30 second to extract any leftover seeds. If the lid is still stuck, repeat

REVERSE - OFF- FORWARD until the ingredients become dislodged. Then twist the lid to open while

pushing downwards on the lid with palms(depending on the ingredient, pour some water down

the feeding tube for quick rinsing to help dislodging).

• The bers from tough ingredients like celery can wrap around the juicing screw and aect

juicer’s performance. Cut the stems that are thick and tough to 10 cm long or less.

• Foam can build up from juicing brous ingredients. Use strainer to remove the foam before

serving.

• For ingredients like pineapple, slice o the rind of the pineapple. Cut the esh of the pineapple

to smaller pieces.

• Recommended amount of juicing per session is 500g. When juicing more than 500g, wash the

top-set before continue juicing.

INGREDIENTS PREPARATION

Slowly insert ingredients with small seeds to prevent the seeds from clogging the strainer.

| (E.g. apples, oranges & tomatoes)

Ingredients with small seeds

(e.g. raspberry, pomegranate, grape):

Fibrous ingredients like celery and kale should be cut into small lengths before juicing

| (E.g. apples, oranges & tomatoes)

Fibrous and/or tough leafy ingredients (e.g. celery, kale, pineapple):

Insert ingredients slowly

to minimize the amount

of leftover seeds in the

strainer.

When juicing leafy

ingredients like celery and

kale, do not collect more

than 500g per session. For

best result, disassemble

and wash the top-set

before juicing again.

If leafy ingredients

wrap around the

juicing screw, open

the lid and remove

the bers before

continue juicing.

It’s best to juice with

ingredients with higher

amount of uid, like

apples or carrots.

Carrots, apples : brous

ingredients = 9:1

[recommended ratio]

For best result, juice with

ingredients with higher

amount of uid(e.g. apple,

pear)

PREPARATION TIPS:

• When juicing frozen ingredients(e.g. raspberry, strawberry), make sure they are completely thawed.

• Thoroughly rinse ingredients like grapes. Take the grapes o and discard the stem.

• For pomegranate, discard the skin and juice only the inner part

EXTRACTION TIPS:

• Depending on the size of the grape, insert 3~5 grapes at a time while monitoring the extraction result.

• Thaw frozen ingredients like pomegranate and raspberry then insert about 1 tablespoon (5g) at a time.

• Frozen ingredients usually lose signi cant amount of  uid from thawing. When juicing, mix milk or

yogurt to balance the uid lost.

PREPARATION TIPS:

• Separate each stem. Cut the outer stems that are thick and tough to 10 cm long or less.

EXTRACTION TIPS:

• One at a time, slowly insert the prepared ingredients.

• Insert more ingredients after the previously inserted ingredients have been completely extracted.

①

Roll leaves in spiral as inserting into the juicer.

②

Insert the leafy part of the ingredients rst then alternate between leafy parts and stems.

③

For ingredients like wheatgrass, grab a handful and insert in a bundle.

Caution |

10 cm

EN

20 21

HOW TO DISASSEMBLE AND CLEAN

• It is not necessary to completely clean

the juicer in between making multiple

juices during a single juicing session.

• When nished with juicing, always

disassemble and clean thoroughly

between juicing sessions to prevent

residue buildup.

Tip |

Clean the base with a soft damp towel

and dry.

Remove the juicing screw, strainer and

rotation wiper unit from the juicing bowl.

Clean with provided brush.

Note | With the smart cap closed, ll the

juicing bowl with water and turn on

the juicer.

Let it run for a moment. Open the

smart cap and let the water run out

of the juicing bowl.

Turn the drum lid counter clockwise to

open.

In order to disassemble, lift o the drum-

set from the base.

Note | • If the towel is dripping wet, make sure

to squeeze out the excess liquid before

using it on the juicer.

Note |

• When moving the appliance, do not lift by

grabbing the feeding tube. Always lift the

appliance by grabbing the base or handle.

Note | • Immediately clean the juicer after each use

by lifting o the drum-set from the base.

(Removing the juicing screw and strainer

while drum-set is still on the base may

cause dripping.)

Switch OFF and unplug the power cord

from the wall outlet.

1

14 6

7

2

3

1

2

Quick Rinsing

Extract all the remaining pulp in the juicing

bowl before stopping the juicer.

For easier clean up, operate the juicer for an

additional 30 seconds after the juice is extracted.

When the drum lid is stuck, press the

REV(REVERSE) – O(OFF) – FWD(FORWARD)

button in this order, switching back and forth

2 to 3 times to dislodge. Then place both hands

on the drum lid and rmly press down while

simultaneously turning the drum lid to open.

* Fill the juicing bowl with water and run the

juicer before opening the drum lid. It may help

to open the drum lid when stuck.

·

Note | Immediately clean the juicer after each

use. If remaining residue in the juicer dries

up, it can make disassembling and clean-

up dicult. The excess build up can cause

poor performance in future uses.

For easier disassembly, place the top-

set in the sink and run the water through

from the top of the top-set.

Thoroughly dry the bottom of the juicing

screw.

TIP |

Place the juicing bowl under running

water.

5

The round brush can clean the juice

spout of the juicing bowl.

Tip |

Note |

Under running water, clean the outside

of the juicing screw with a dish scrub. Use

the tip of the cleaning brush to push out

any residue in the crevices on the bottom

of the juicing screw.

After juicing ingredients with seeds, make

sure to thoroughly clean the bottom

crevice of the juicing screw. (If this area

isn’t properly cleaned, it can cause the

part to be damaged.)

Thoroughly clean the juicing screw

ensuring that the juicing screw is clean

without any residue.

Completely dry before using.

EN

22 23

OPTIONAL | HOW TO USE THE CLEANING TOOL

Hold the cleaning tool with one hand and insert

the strainer into the cleaning tool.

Under running water, rotate the cleaning

tool and the strainer in opposite directions to

clean.

Thoroughly rinse the inside and outside of

the strainer under running water.

After cleaning, remove the strainer from the

cleaning tool. Dry before storing.

HOW TO CLEAN SILICONE PARTS

The cleaning tool makes clean-up quick and easy.

Completely dry after cleaning.

Use the included cleaning brush to remove hard to reach bits after using the cleaning tool.

Tip |

Note |

1

4

2

3

Note | Insert the strainer until you hear a click.

Silicone Brush

Pull out the silicone brush from

the rotation wiper to clean.

After cleaning, insert into the slot

with the tail pointing down as

shown in the illustration.

Smart Cap

Remove from the juice spout

to clean.

After cleaning, attach the smart

cap to the smart cap silicone on

the juice spout.

Clean the rotation wiper under running water.

Thoroughly dry after cleaning. Before assembling the top-set, ensure that the compression

silicone and silicone ring are rmly inserted.

If the compression silicone and silicone ring are not rmly inserted, juice may leak from the

bottom of the juicing bowl.

Tip |

Note |

Silicone Ring

Remove the silicone ring from

strainer to clean.

After cleaning, push in the silicone

ring as shown in the picture.

EN

2524

TROUBLESHOOTING Q&A

When there is no power to the juicer:

· Check if the power cord is properly plugged in.

· Check if the drum lid and the juicing bowl are

properly assembled.

· Check if the top-set and the body are properly

assembled.

· Juicer will not operate if parts are not

assembled properly.

Low juice yield:

· Dierent ingredients hold dierent amounts of

uid that will yield dierent amounts of juice.

· If the ingredients are not fresh, they may

contain reduced amount of uid, which will

yield less juice. Sock ingredients in cold water

for about 30 min prior to juicing for the best

result.

· Check if the compression silicone is rmly

inserted.

· If the ingredient itself has low water content,

it may help to soak it in water before juicing.

· If juicing ingredients with small seeds, after a

few servings, it may reduce the juice yield.

For best result, disassemble and wash the top-

set in between juicing.

· If there is seed residue on the bottom of the

strainer, this can aect juicer performance and

the overall juice yield.

There is too much pulp in the juice:

· To reduce the ne pulp, clean the top-set

frequently and extract the pulp.

· Use a mesh strainer and put the juice through

it to collect the unwanted pulp.

· If the strainer and the screw are damaged

and aecting the juicer’s performance, it is

recommended the parts be replaced.

*The lifetime of each part may vary depending

on length and method of use and ingredients

extracted.

The drum lid will not close:

· Make sure the juicing screw is pushed all the

way in to the strainer in order for the drum lid

to close properly.

· If the juicing screw is not properly in position,

the drum lid may not close.

Odd noise from the juicer:

· Check if the parts are assembled correctly.

Try reassembling the parts and listen for the

odd noise.

· Do not start the juicer unless there are

ingredients and/or liquid in it.

· Operating the juicer without ingredients can

cause damage to the screw.

· If the juicer is operated without ingredients or

liquid, the noise level can increase and also can

lead to damage.

· The friction noise from the juicing screw and

the strainer will disappear when ingredients

are inserted into the juicer.

· If the noise occurs when ingredients are

inserted into the juicer, check the size of the

ingredients. Do not insert anything over 1 inch

in thickness.

· Depending on the type of ingredients,

the dimensions can be smaller.

· The noise can occur if the juicer is operated on

an uneven or slanted surface. Place the juicer

on a horizontally at surface when operating.

The extracted pulp is very moist:

· During the very beginning of extraction,

the pulp can be more moist.

· Depending on the ingredient’s condition,

the extracted pulp can be aected; especially

when the ingredient is not fresh, the juice can

be extracted with the pulp.

During operation, the juicing bowl shakes.

· The juicing screw and the strainer are set up to

crush and squeeze the ingredients. It is normal

for the juicing screw and the strainer to vibrate.

· If the ingredient contains strong ber,

the vibration from the top-set may be stronger.

During juicing, the juicer stopped:

· Check the power cord and make sure it is

plugged in correctly.

· Check that all the parts are correctly assembled.

· If too many ingredients are inserted at one time,

this can cause the juicer to stop.

· When the juicer stops because there are too

many ingredients inserted in it, press the

REV(REVERSE) - O(OFF) - FWD(FORWARD) button

in this order, switching back and forth 2 to 3 times.

· The reverse setting will push the ingredients up,

and the forward setting will pull the ingredients

down.

· After using more than 30 minutes, if the juicer

stops due to the overload protection, let the

juicer cool for 30 minutes to 1 hours before

juicing again.

· If there are hard seeds within the ingredients,

remove them before juicing. Hard seeds can

damage the juicer.

Layers of separation in the juice:

·

Depending on the density of the ingredients, the

extracted juice may show layers of dierent juices.

It is dierent from separation due to oxidation

caused by juicing with a high-speed juicer.

The drum lid is stuck:

· After juicing, let the juicer operate for another

30 seconds to extract the remaining pulp.

·

If there is too much pulp in the top-set, this can cause

the drum lid to not open. In this situation, press

the REV(REVERSE) - O(OFF) - FWD(FORWARD) button in

the order, switching back and forth 2 to 3 times. Then

place both hands on the drum lid and firmly press down

while simultaneously turning the drum lid to open.

· Pour water down the feeding tube to rinse out

the insides and then try opening the drum lid.

Juice dripping down the body:

·

If the compression silicone on the bottom of

the juicing bowl is not plugged in correctly,

the juice may seep out on to the juicer body.

Before assembling the parts, check and make sure

the compression silicone is plugged in correctly.

Is it possible to juice ingredients with

tough ber?

· Ingredients like celery or ginger contain long

bers that may wrap around the juicing screw

and aect the juicer’s performance. When

juicing brous ingredients, do not collect more

than 1 lb. of juice. After collecting this quantity

or less, clean the top-set completely before

juicing again.

Discoloration of the plastic parts:

· After juicing, if the juicer is not cleaned right

away, the remaining pulp inside the top-set

can dry up which can make disassembling and

cleaning hard. This can also aect the juicer’s

performance and color.

· Ingredients that are rich in carotenoids such

as carrots and spinach may dye plastic parts.

When the parts are dyed with carotenoids, rub

vegetable oil in to the dyed areas and use mild

detergent to clean.

· Vegetable oil should only be used during

clean-up for parts that are discolored. Do not

use vegetable oil on the juicing screw or the

strainer. If vegetable oil or oil from animal fat

gets on the juicing screw or the strainer, this

can aect the juicer’s performance and may

result in damaged parts.

· The silicone pieces on the top-set can be

detached to be thoroughly cleaned.

Using for purposes other than juicing:

· This juicer is designed to juice ingredients like

fruits and vegetables.

· Do not use the juicer for extracting vegetable oil.

· Do not juice ingredients with high contents of

vegetable/ animal oil.

· If vegetable/animal oil gets on the juicing screw

or the strainer, this can aect the performance

of the juicer and could result in damaged parts.

EN

27

SPECIFICATIONS

Voltage

Power Consumption

Maximum Use

Weight

Dimension

Manufacturer

Type

AC220-240V, 50/60Hz

240W

Less than 30 min

6,9kg

228 x 208 x 446 (mm)

NUC Electronics Co., Ltd.

Low speed compression

Witt A/S

Gødstrup Søvej 9,

7400 Herning, Denmark

Mail : [email protected]

Product

Model

Juicer

NS-721CEM

Guarantee

A two year guarantee on manufacture and material defects (ve years on the motor) is granted on your

new appliance valid from the documented purchase date. The guarantee includes materials, salary and

transport. When contacting service please state the appliance model and serial number.

The guarantee does not cover:

• Defects and damages which are not caused by manufacture and material defects.

• If original spare parts have not been used.

• If the instructions in the manual have not been carried out.

• If the installation has not been carried out according to this manual.

• If unauthorized personnel has carried out installation or repair word.

Transport damages

A transport damage observed when the dealer delivers the appliance at the customer is solely a

matter between the customer and the dealer. If the customer has carried out the transport alone the

manufacture / supplier cannot be held responsible for transport damages. All transport damages must

be reported no later than 24 hours after delivery otherwise all claims will be rejected.

Unnecessary service visits

If a service technician is called out to a defect and the customer could have corrected the defect

without help e.g. by following the instructions within this manual or by changing a fuse the customer

will be charged all service costs – even under guarantee.

Commercial purchase

Commercial purchases are any purchase of appliances not used in a domestic household but instead

are used for commercial purposes e.g. in a restaurant, café etc. or used to rent out or used for any

other purpose including several users. In case of commercial purchase no guarantee is granted on this

appliance since this is only meant for domestic household use.

GUARANTEE

EN

26

KUVINGS

Slow juicer til hele frugter

Brugsanvisning

• Læs venligst hele brugsanvisningen

omhyggeligt igennem, inden Kuvings

tages i brug.

• Farven på produktet kan variere.

•

Udelukkende til private husholdninger.

DK

C9600

M7

30 31

SIKKERHEDSANVISNINGER

DK

Før Kuvings tages i brug, skal man omhyggeligt erne al emballage.

Sørg for at holde emballagen væk fra børn, da det kan være farligt legetøj

for dem.

Straks efter ernelse af emballagen skal man undersøge, om Kuvings er

beskadiget. Hvis Kuvings er beskadiget, eller hvis man er i tvivl om,

om den har en skade, skal man kontakte den butik, hvor produktet er købt.

Kuvings må IKKE tages i brug, hvis den er beskadiget. En skade skal straks

anmeldes til den butik, hvor produktet er købt.

Apparatet er beregnet til at presse frugt og grøntsager. Apparatet er blevet

konstrueret til brug i husholdningen. Det er ikke beregnet til kommerciel

brug. Overholdes dette ikke, er der risiko for produktskade.

Rengør ikke baseenheden under rindende vand, og nedsænk den ikke

i en balje vand. Overholdes dette ikke, er der risiko for person- og/eller

produktskade.

Når apparatets forbindelse til el-nettet afbrydes, så tag altid fat i stikket.

Træk ikke i ledningen. Sørg for at ledningen ikke bøjes eller vrides og undgå

kontakt med varmekilder. Undgå at ledningen hænger ud over et bord etc.

Overholdes dette ikke, er der risiko for brand og elektrisk stød.

Benyt aldrig apparatet, hvis ledningen eller stikket sidder løs eller er

beskadiget. Kontakt en fagmand, hvis ledningen er beskadiget.

Forsøg aldrig selv at reparere eller modicere ledningen.

Overholdes dette ikke, er der risiko for brand og elektrisk stød.

Er udelukkende beregnet til indendørs brug.

Sluk for apparatet efter afsluttet brug, og træk stikket ud af kontakten.

Sørg for at motoren er helt stoppet, inden maskinen skilles ad for rengøring.

Træk stikket ud af kontakten inden rengøring og efter brug.

Rør aldrig ved dele i bevægelse. Fare for person- og/eller produktskade.

Benyt aldrig uoriginale dele. Fare for brand, elektrisk stød samt produktskade.

Sørg for at påfyldningsenheden er låst på plads, inden maskinen igangsættes.

Brug stopperen – ikke ngre eller bestik, til at indføre ingredienser i apparatet.

Hvis noget sidder fast og stopperen ikke er tilstrækkelig, slukkes maskinen og

påfyldningsenheden afmonteres, hvorefter det, der sidder fast, ernes.

Benyt aldrig maskinen med defekte dele.

Sørg for at benytte kanden til opsamling af frugtkød.

Forsøg ikke selv at reparere eller modicere maskinen.

Benyt ikke apparatet mere end 30 min. ad gangen. Risiko for produktskade.

Dette apparat kan bruges af børn i alderen fra 8 år og derover samt

personer med nedsatte fysiske, sensoriske eller mentale evner eller

mangel på erfaring og viden, hvis de overvåges eller har fået grundig

instruktion i brugen af apparatet på en sikker måde og forstår de

involverede risici.

7.

8.

9.

10.

11.

12.

13.

14.

15.

16.

17.

18.

19.

1.

2.

3.

4.

5.

6.

Kuvings må ikke betjenes af børn eller personer med fysiske, sensoriske eller

mentale gener eller personer, som ikke råder over tilstrækkelig erfaring og

kundskaber. Undtaget er de tilfælde, hvor de instrueres i brugen af apparatet

og hvor de i begyndelsen er under opsyn af en person, som er ansvarlig for

deres sikkerhed. Før tilsyn med børn, så de ikke leger med apparatet.

Læs venligst hele brugsanvisningen omhyggeligt igennem, inden Kuvings

tages i brug. På denne måde beskyttes brugeren, og man undgår skade på

produktet.

Brugsanvisningen skal gemmes, så man kan drage nytte af den ved evt.

senere spørgsmål. Hvis Kuvings overdrages/sælges, skal brugsanvisningen

følge Kuvings og gives til den nye ejer.

ㆍ

Hvis apparatet gives i gave, skal manualen medfølge apparatet.

ㆍ

Denne manual skal ydermere være tilgængelig i et andet format,

f.eks. på web, www.kuvings.com.

32 33

De følgende anvisninger garanterer din sikkerhed. Læs dem grundigt inden ibrugtagning.

ADVARSEL : Fare for alvorlige personskader.

FORSIGTIG : Fare for person- og/eller produktskade.

Forbudt

Følg anvisningen

Træk stikket ud af kontakten

Må ikke skilles ad

Kræver handling

Fare for elektrisk stød

SIKKERHEDSANVISNINGER SIKKERHEDSANVISNINGER

Forsøg ikke selv at reparere eller skille basen ad. Forsøg ikke selv at

modicere maskinen.

→ Fare for brand, elektrisk stød, person- og/eller produktskade.

Delene må ikke rengøres i opvaskemaskinen eller i kogende varmt vand.

→ Fare for hurtig nedslidning.

Placer ikke maskinen på en ujævn overade.

→ Fare for person- og/eller produktskade, hvis maskinen vælter.

Sørg for at ledningen ikke bøjes eller vrides og undgå kontakt med

varmekilder. Undgå at ledningen hænger ud over et bord etc.

→ Fare for brand og elektrisk stød.

Sørg for at holde maskinen væk fra børn og opbevar den et sikkert sted.

→ Fare for person- og/eller produktskade.

Opbevar og betjen ikke maskinen i nærheden af en varmekilde.

→ Fare for maskinen bliver deform og misfarvet.

Benyt aldrig kemiske rengøringsmidler til rengøring, og benyt

ingen brandfarlige spraydåser i nærheden af apparatet.

→ Fare for brand og misfarvning.

Benyt aldrig en forlængerledning eller en multi-stikdåse,

når Kuvings benyttes.

→ Fare for brand og eksplosion.

Berør ikke ledningen eller stikket med våde hænder.

→ Fare for elektrisk stød.

Rengør ledningen med en tør klud, hvis den er beskidt.

→ Fare for elektrisk stød og brand.

Tab ikke maskinen eller placer ikke meget tunge ting ovenpå den.

→ Fare for produktskade.

Træk ikke stikket ud af kontakten ved at hive i ledningen.

Tag i stedet fat i stikket.

→ Fare for produktskade og elektrisk stød.

Brug stopperen – ikke ngre eller bestik, til at indføre ingredienser

i apparatet.

→ Fare for person- og/eller produktskade.

Lad ikke maskinen arbejde uden opsyn. Træk stikket ud af kontakten,

når maskinen ikke bruges.

Tænd aldrig for maskinen, hvis den er tom.

→ Fare for produktskade.

DK

34 35

+

DELE

2. Påfyldningsenhed

3. Saftbeholder

4. Kande til frugtkød

7. Juicekande

5. Smart låg

6. Base

1. Påfyldningsenhed

10. Saftpressersnegl

13.Rengøringværktøj

9. Si

11. Stopper

8. Roterende børste

12. Rengøringsbørste

Placer de røde cirkler ● ud for hinanden,

som vist på illustrationen. Når maskinen

er samlet, drejes påfyldningsenheden

mod uret, for at låse den fast.

Trin 1

Samleanvisning (foran på maskinen)

Trin 2

Samleanvisning (bag på maskinen)

Placer påfyldningsenheden på saftbeholderen.

Bag på maskinen, placeres pil ned▼(bag på

påfyldningsenheden) ud for OPEN på basen

og drej til CLOSE position .

Stopper

Tilpas

Placer cirklerne ●på stopperen og

påfyldningsenheden ud for hinanden, og

skub stopperen ind i påfyldningsenheden.

aftageligt

DK

36 37

SAMLEANVISNING

Monter sien i den roterende børste.

Placer herefter samlingen i saftbeholderen.

Sørg for at den røde cirkel ●på sien er

placeret på niveau med den røde cirkel ●

på saftbeholderen.

Sneglen skal være låst på plads, ellers kan

indførselsenheden ikke monteres.

Bemærk |

Apparatet fungerer ikke med mindre

pilen ned ▼står lige ud for CLOSE på

baseenheden.

Bemærk |

Trin 1 Trin 2

Monter sneglen i sien. Drej til den klikker

på plads.

Kontroller inden

ibrugtagning

1 2

3

4

5

Placer kanden til opsamling af frugtkød

under frugtkødsmundstykket, og

juicekanden under juicemundstykket,

som vist på illustrationen.

Placer påfyldningsenheden på saftbeholderen.

Bag på maskinen, placeres pil ned ▼

(bag på påfyldningsenheden) ud for OPEN

på basen og drej til CLOSE position .

Open

Close

Aftagelig

OPEN / CLOSE ses bag på maskinen.

6

Tag fat øverst på påfyldningsenheden for

let montering, som vist på illustrationen.

TIP

Monter indførselsenheden på

saftbeholderen, og sørg for at den røde

cirkel ●på indførselsenheden er placeret

i niveau med den røde cirkel ●på

saftbeholderen. Drej med uret til den røde

cirkel ●

på saftbeholderen er på niveau

med CLOSE II på påfyldningsenheden .

foran på maskinen bag på maskinen

DK

• Vask alle dele grundigt inden maskinen bruges første gang.

• Sørg for at den roterende børste og siens silikonering er korrekt monterede.

38 39

Brug Smart låget til at lave blandet juice, til at undgå saften drypper,

eller skyl systemet igennen mellem forskellige typer juice.

Når juicen er presset helt færdig, slukkes maskinen (OFF-knappen).

BRUGSANVISNING

Efter ingrediensforberedelsen, sættes stikket i stikkontakten.

Tryk på FWD(FORWARD)-knappen for at tænde maskinen.

De forberedte ingredienser kommes i maskinen en ad gangen.

• Rør ikke ved ledningen eller stikket med våde hænder. Fare for elektrisk stød,

kortslutning eller brand.

• Kontroller stikkontakten opfylder de gældende sikkerhedskrav i henhold til

landets love og regler.

• FWD(Forward): Trækker ingredienserne ned, og presser dem langsomt.

• REV(Reverse): Skubber ingredienserne tilbage for at løsne evt. fastsiddende

ingredienser.

• Fiberholdige bladgrøntsager (selleri, kål etc.)

» Adskil hver stængel. Skær de yderste stængler, som er tykke og hårde, så de har en

længde på 10 cm eller mindre. Adskil hver stængel.

» Saml bladgrøntsagerne i bundter og kom dem i maskinen. Skift evt. mellem

stængler og blade.

• Inden saftpresningen ernes hårde kerner og sten fra ingredienserne.

• Hvis der presses frosne ingredienser med små kerner, skal de være helt optøede.

• Kom ingredienserne i en ad gangen.

• Placer cirklerne ●på stopperen og påfyldningsenheden ud for hinanden, og skub

stopperen ind i påfyldningsenheden.

• Efter indføring af ingredienserne, bruges stopperen efter behov.

Overdreven brug af stopperen kan forringe juicekvaliteten.

» Ved bløde ingredienser, som tomater og æbler, bruges stopperen ved behov.

Konstant brug af stopperen ved bløde ingredienser, kan forringe juicekvaliteten.

• Hvis ingredienserne i maskinen ikke er blevet fuldstændig presset, kan det være

svært at åbne påfyldningsenheden. Efter afsluttet presning køres maskinen

yderligere 30 sekunder, for at sikre, at maskinen udskiller resterende frugtkød.

• Hvis påfyldningsenheden sidder fast, køres REV(REVERSE) – O(OFF) –

FWD(FORWARD) funktionen (i den nævnte rækkefølge) 2-3 gange for at løsne evt.

fastsiddende ingredienser. Placer derefter hænderne på påfyldningsenheden, og

pres kraftigt ned samtidigt med at påfyldningsenheden drejes mod uret til OPEN.

» Afhængig af ingredienstype kan der hældes vand i påfyldningsenheden for at

rense saftbeholderen, hvorefter påfyldningsenheden forsøges åbnet.

• Med lukket låg opnås en blandet juice, ved brug af forskellige frugter, grøntsager

og mælk, bananer, bønner etc.

• Efter presningen lukkes låget for at forhindre, at juicen drypper, specielt når

påfyldningsenheden skilles fra saftbeholderen.

• Hvis der presses forskellige typer juice, skylles maskinen igennem med et glas

vand for at forhindre, at der tilføres forskellige smage. Hold låget lukket, mens

maskinen skylles igennem.

• Lad låget være åbnet, når der presses ingredienser, der producerer meget skum

(f.eks. æbler og selleri).

• Vær meget opmærksom, når der presses, mens låget er lukket, da saften kan løbe

over, hvis kapaciteten overstiger maks. i saftbeholderen.

• REV(Reverse): Skubber ingredienserne tilbage for at løsne evt. fastsiddende

ingredienser.

REV(Reverse)-funktionen virker kun, når knappen holdes nede.

• O(OFF)-knappen slukker maskinen. Tryk herefter på REV(Reverse). Hold REV(Reverse)-

knappen nede i 2-3 sekunder og slip derefter knappen. Gentag efter behov.

Sørg for at maskinen stopper helt, inden REV(Reverse)-funktionen benyttes.

Dette forhindrer funktionsfejl.

• Hvis maskinen fortsat ikke fungerer efter ovenstående anvisninger, skal maskinen

skilles ad og rengøres, inden maskinen igen benyttes.

Hvis maskinen stopper under drift:

Tryk på O(OFF)-knappen og tryk og hold derefter

REV(Reverse)-knappen nede til ingredienserne løsner sig.

Gentag ”REV(Reverse) – O(OFF) – FWD(Forward)

funktionen” efter behov.

FWD : Trækker ingredienserne ned

O : Stopper maskinen

REV : Skubber ingredienserne tilbage

Bemærk |

TIP |

Bemærk |

TIP |

Bemærk |

Hvis ingredienserne sidder fast i sneglen, og påfyldningsenheden ikke kan åbnes, skal man trykke

på O(OFF)-knappen. Tryk og hold derefter REV(Reverse)-knappen nede til ingredienserne løsner sig.

Gentag ”REV(Reverse) – O(OFF) – FWD(Forward) funktionen” indtil det ønskede resultat er opnået.

Trin 1 Trin 3

Trin 4

Trin 5

Trin 2

DK

▶ ▶ ▶

4

1 3

2

O(OFF) O(OFF)REV(REVERSE) FWD(FORWARD)

Sidan laddas ...

Witt C9600 Bruksanvisning

Denna manual är också lämplig för

Witt C9600 Bruksanvisning

på andra språk

Relaterade papper

Andra dokument