Trend T12 Användarmanual

T12/T14

EN Original Instructions

DE Übersetzung Der Originalanleitung

FR Traduction Des Instructions Originales

NL Vertaling Van De Originele Instructies

Översättning Av De Ursprungliga Instruktionerna

SE

P.8

P.21

P.35

P.49

P.63

T12/T14

-2-

Fig. A

1

T12

T14

2

4

12

16

20

17

15

14

18

19

8

9

11

10

7

3

6

5

13

T12/T14

-3-

Fig. B1

Fig. B3

Fig. D

Fig. B2

Fig. C

45

6

7

9

35

54

14

16

17

12

18

15

19

T12/T14

-4-

Fig. F

Fig. H

Fig. G

Fig. I

Fig. E 11

10

55

30 31 29

28

27

57

8

9

10

58

60

24

59

25

4

51

5

T12

T14

T12/T14

-5-

1

2

3

4

1

2

3

4

Fig. L

Fig. N

Fig. M

Fig. O

Fig. J Fig. K

10

1028

28

2

53

2

26

10 52

36

37

34

32

33

26

28

29

T12/T14

-6-

Fig. Q

Fig. R

Fig. P

34

38

49

48

47

40

43

46

44

42

41

50

T14

T12/T14

-7-

Fig. S3

61

63

51 51

4 4

62 62

5 5

64

Fig. S1 Fig. S2

T14

EN - T12/T14

-8-

EN - T12 & T14

Thank you for purchasing this Trend product, we hope

you enjoy many years of creative and productive use.

Please remember to return your guarantee card within 28

days of purchase.

TECHNICAL DATA

T12EL T12E T14E

Voltage V AC 115 230 230

Type 1 1 1

Power input W 2100 2300 2300

No load speed min 1 9000

22000

9000

22000

9000

22000

Router carriage mm 2 column 2 column 2 column

Max cutter diameter

(Portable Router)

mm 50 50 50

Max cutter diameter

in table

mm 50 50 86

Collet size for Europe mm - 12 12

Collet size for UK

and ROI

inch 1/2 1/2 1/2

Weight kg 6.4 6.4 6.5

Noise values and vibration values (triax vector sum) according

to EN62841 2 17:

LPA (emission sound

pressure level)

dB(A) 94.2 95.1 95.1

LWA (sound power

level)

dB(A) 105.2 106.1 106.1

K (uncertainty for the

given sound level)

dB(A) 2.5 2.5 2.5

Vibration emission

value ah,hv =

m/s24.1 3.1 3.1

Uncertainty K = m/s20.31 0.31 0.31

The vibration and/or noise emission level given in this

information sheet has been measured in accordance

with a standardised test given in EN62841 and may be

used to compare one tool with another. It may be used

for a preliminary assessment of exposure.

WARNING: The declared vibration and/or

noise emission level represents the main applications

of the tool. However if the tool is used for different

applications, with different accessories or poorly

maintained, the vibration and/or noise emission may

differ. This may signiﬁcantly increase the exposure level

over the total working period.

An estimation of the level of exposure to vibration and/or

noise should also take into account the times when the

tool is switched off or when it is running but not actually

doing the job. This may signiﬁcantly reduce the exposure

level over the total working period.

Identify additional safety measures to protect the

operator from the effects of vibration and/or noise such

as: maintain the tool and the accessories, keep the

hands warm (relevant for vibration), organisation of work

patterns.

EC DECLARATION OF CONFORMITY

MACHINERY DIRECTIVE

T12E & T14E

Plunge Router

Trend Tool Technology Ltd declares that these products

described under Technical Data are in compliance with:

2006/42/EC, EN 62841-1:2015 + AC:2015; EN 62841-2-

17:2017.

These products also comply with Directive 2014/30/EU

and 2011/65/EU. For more information, please contact

Trend Tool Technology Ltd at the following address or

refer to the back of the manual.

The undersigned is responsible for compilation of the

technical ﬁle and makes this declaration on behalf of

Trend Tool Technology Ltd

Neil McMillan

Technical Director

Trend Tool Technology Ltd

Unit 6 Odhams Trading Estate

St Albans Road, Watford

Herts, WD24 7TR

United Kingdom

01/11/21

UK DECLARATION OF

CONFORMITY

THE SUPPLY OF MACHINERY

(SAFETY) REGULATIONS 2008

T12E & T14E

Plunge Router

Trend Tool Technology Ltd declares that these products

described under “technical data” are in compliance with:

The Supply of Machinery (Safety) Regulations, 2008,

S.I. 2008/1597 (as amended), BS EN 62841-1:2015 +

AC:2015; BS EN 62841- 2-17:2017.

Technical File Contact

Trend Tool Technology Ltd

3rd Floor, Kilmore House,

Park Lane, Spencer Dock,

Dublin 1, Ireland

EN - T12/T14

-9-

tool is switched off or when it is running but not actually

doing the job. This may signiﬁcantly reduce the exposure

level over the total working period.

Identify additional safety measures to protect the

operator from the effects of vibration and/or noise such

as: maintain the tool and the accessories, keep the

hands warm (relevant for vibration), organisation of work

patterns.

EC DECLARATION OF CONFORMITY

MACHINERY DIRECTIVE

T12E & T14E

Plunge Router

Trend Tool Technology Ltd declares that these products

described under Technical Data are in compliance with:

2006/42/EC, EN 62841-1:2015 + AC:2015; EN 62841-2-

17:2017.

These products also comply with Directive 2014/30/EU

and 2011/65/EU. For more information, please contact

Trend Tool Technology Ltd at the following address or

refer to the back of the manual.

The undersigned is responsible for compilation of the

technical ﬁle and makes this declaration on behalf of

Trend Tool Technology Ltd

Neil McMillan

Technical Director

Trend Tool Technology Ltd

Unit 6 Odhams Trading Estate

St Albans Road, Watford

Herts, WD24 7TR

United Kingdom

01/11/21

UK DECLARATION OF

CONFORMITY

THE SUPPLY OF MACHINERY

(SAFETY) REGULATIONS 2008

T12E & T14E

Plunge Router

Trend Tool Technology Ltd declares that these products

described under “technical data” are in compliance with:

The Supply of Machinery (Safety) Regulations, 2008,

S.I. 2008/1597 (as amended), BS EN 62841-1:2015 +

AC:2015; BS EN 62841- 2-17:2017.

Technical File Contact

Trend Tool Technology Ltd

3rd Floor, Kilmore House,

Park Lane, Spencer Dock,

Dublin 1, Ireland

These products conform to the following UK Regulations

Electromagnetic Compatibility Regulations, 2016,

S.I.2016/1091 (as amended).

The Restriction of the Use of Certain Hazardous

Substances in Electrical and Electronic Equipment

Regulations 2012, S.I. 2012/3032 (as amended).

For more information, please contact Trend Tool

Technology Ltd at the following address or refer to the

back of the manual.

The undersigned is responsible for compilation of the

technical ﬁle and makes this declaration on behalf of

Trend Tool Technology Ltd .

Neil McMillan

Technical Director

Trend Tool Technology Ltd

Unit 6 Odhams Trading Estate

St Albans Road, Watford

Herts, WD24 7TR

United Kingdom

01/11/21

WARNING: To reduce the risk of injury, read

the instruction manual.

Deﬁnitions: Safety Guidelines

The deﬁnitions below describe the level of severity

for each signal word. Please read the manual and pay

attention to these symbols.

DANGER: Indicates an imminently hazardous

situation which, if not avoided, will result in death or

serious injury.

WARNING: Indicates a potentially hazardous

situation which, if not avoided, could result in death or

serious injury.

CAUTION: Indicates a potentially hazardous

situation which, if not avoided, may result in minor or

moderate injury.

NOTICE: Indicates a practice not related

to personal injury which, if not avoided, may result in

property damage.

Denotes risk of electric shock.

Denotes risk of ﬁre.

GENERAL POWER TOOL SAFETY

WARNINGS

WARNING: Read all safety warnings,

instructions, illustrations and speciﬁcations

provided with this power tool. Failure to follow all

instructions listed below may result in electric shock, ﬁre

and/or serious injury.

SAVE ALL WARNINGS AND

INSTRUCTIONS FOR FUTURE

REFERENCE

The term “power tool” in the warnings refers to your

mains- operated (corded) power tool or battery-operated

(cordless) power tool.

1) Work Area Safety

a) Keep work area clean and well lit. Cluttered or

dark areas invite accidents.

b) Do not operate power tools in explosive

atmospheres, such as in the presence of

ﬂammable liquids, gases or dust. Power tools create

sparks which may ignite the dust or fumes.

c) Keep children and bystanders away while

operating a power tool. Distractions can cause you to

lose control.

2) Electrical Safety

a) Power tool plugs must match the outlet. Never

modify the plug in any way. Do not use any

adapter plugs with earthed (grounded) power

tools. Unmodiﬁed plugs and matching outlets will

reduce risk of electric shock.

b) Avoid body contact with earthed or grounded

surfaces such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric

shock if your body is earthed or grounded.

c) Do not expose power tools to rain or wet

conditions. Water entering a power tool will increase

the risk of electric shock.

d) Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool.

Keep cord away from heat, oil, sharp edges or

moving parts. Damaged or entangled cords increase

the risk of electric shock.

e) When operating a power tool outdoors, use an

extension cord suitable for outdoor use. Use of a

cord suitable for outdoor use reduces the risk of electric

shock.

EN - T12/T14

-10-

f) If operating a power tool in a damp location is

unavoidable, use a residual current device (RCD)

protected supply. Use of an RCD reduces the risk of

electric shock.

3) Personal Safety

a) Stay alert, watch what you are doing and use

common sense when operating a power tool. Do

not use a power tool while you are tired or under

the inﬂuence of drugs, alcohol or medication. A

moment of inattention while operating power tools may

result in serious personal injury.

b) Use personal protective equipment. Always

wear eye protection. Protective equipment such as

dust mask, non-skid safety shoes, hard hat or hearing

protection used for appropriate conditions will reduce

personal injuries.

c) Prevent unintentional starting. Ensure the

switch is in the off-position before connecting to

power source and/or battery pack, picking up or

carrying the tool. Carrying power tools with your ﬁnger

on the switch or energising power tools that have the

switch on invites accidents.

d) Remove any adjusting key or wrench before

turning the power tool on. A wrench or a key left

attached to a rotating part of the power tool may result in

personal injury.

e) Do not overreach. Keep proper footing and

balance at all times. This enables better control of the

power tool in unexpected situations.

f) Dress properly. Do not wear loose clothing or

jewellery. Keep your hair and clothing away from

moving parts. Loose clothes, jewellery or long hair can

be caught in moving parts.

g) If devices are provided for the connection of

dust extraction and collection facilities, ensure

these are connected and properly used. Use of dust

collection can reduce dust-related hazards.

h) Do not let familiarity gained from frequent use

of tools allow you to become complacent and

ignore tool safety principles. A careless action can

cause severe injury within a fraction of a second.

4) Power Tool Use and Care

a) Do not force the power tool. Use the correct

power tool for your application. The correct power

tool will do the job better and safer at the rate for which

it was designed.

b) Do not use the power tool if the switch does

not turn it on and off. Any power tool that cannot be

controlled with the switch is dangerous and must be

repaired.

c) Disconnect the plug from the powersource and/

or the battery pack, if detachable, from the power

tool before making any adjustments, changing

accessories, or storing power tools. Such preventive

safety measures reduce the risk of starting the power

tool accidentally.

d) Store idle power tools out of the reach of

children and do not allow persons unfamiliar with

the power tool or these instructions to operate the

power tool. Power tools are dangerous in the hands of

untrained users.

e) Maintain power tools and accessories. Check

for misalignment or binding of moving parts,

breakage of parts and any other condition that

may affect the power tool’s operation. If damaged,

have the power tool repaired before use. Many

accidents are caused by poorly maintained power tools.

f) Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges are

less likely to bind and are easier to control.

g) Use the power tool, accessories and tool bits,

etc. in accordance with these instructions, taking

into account the working conditions and the work

to be performed. Use of the power tool for operations

different from those intended could result in a hazardous

situation.

h) Keep handles and grasping surfaces dry, clean

and free from oil and grease. Slippery handles and

grasping surfaces do not allow for safe handling and

control of the tool in unexpected situations.

5) Service

a) Have your power tool serviced by a qualiﬁed

repair person using only identical replacement

parts. This will ensure that the safety of the power tool

is maintained.

Safety Instructions for Routers

a) Hold the power tool by insulated gripping

surfaces only, because the cutter may contact

its own cord. Cutting a “live” wire may make exposed

metal parts of the power tool “live” and could give the

operator an electrical shock.

b) Use clamps or another practical way to secure

and support the workpiece to a stable platform.

Holding the work by your hand or against the body

leaves it unstable and may lead to loss of control.

c) Keep handles dry, clean and free from oil and

grease. This will enable better control of the tool.

d) Maintain a ﬁrm grip with both hands on the tool

to resist starting torque. Maintain a ﬁrm grip on the

tool at all times while operating.

e) Keep hands away from cutting area above and

below the base. Never reach under the workpiece

for any reason. Keep the router base ﬁrmly in contact

with the workpiece when cutting.

EN - T12/T14

-11-

f) Never touch the bit immediately after use. It

may be extremely hot.

g) Be sure that the motor has stopped completely

before you lay the router down. If the bit is still

spinning when the tool is laid down, it could cause injury

or damage.

h) Be sure that the router bit is clear of the

workpiece before starting the motor. If the bit is

in contact with the workpiece when the motor starts, it

could make the router jump, causing damage or injury.

i) The permitted speed of the cutting bit must be

at least equal to the maximum speed marked on

the power tool. If cutting bits run faster than their rated

speed, they may break and ﬂy off.

j) Always follow the bit manufacturer’s speed

recommendations as some bit designs require

speciﬁc speeds for safety or performance. If you

are unsure of the proper speed or are experiencing any

type of problem, contact the bit manufacturer.

k) Do not use cutters larger than 50 mm (2”)

unless the router is ﬁtted in a router table.

Do not use cutters larger than 86 mm (3 3/8”) in

this tool.

RESIDUAL RISKS

WARNING: We recommend the

use of a residual current device with

a residual current rating of 30mA or

less.

In spite of the application of the relevant safety

regulations and the implementation of safety devices,

certain residual risks cannot be avoided. These are:

• Impairment of hearing.

• Risk of personal injury due to ﬂying particles.

• Risk of burns due to accessories becoming hot during

operation.

• Risk of personal injury due to prolonged use.

SAVE THESE INSTRUCTIONS

Electrical Safety

The electric motor has been designed for one voltage

only. Always check that the power supply corresponds to

the voltage on the rating plate.

Your tool is double insulated in accordance with

EN62841; therefore no earth wire is required.

115V machines are intended to be used with a safety

transformer manufactured to BS EN 61558 and

BS 4343. Never work without this transformer in place.

If the supply cord is damaged, it must be replaced only

by Trend Tool Technology Ltd or an authorised service

organisation.

Mains Plug Replacement (U.K. & Ireland Only)

If a new mains plug needs to be ﬁtted:

• Safely dispose of the old plug.

• Connect the brown lead to the live terminal in the plug.

• Connect the blue lead to the neutral terminal.

WARNING: No connection is to be made to

the earth terminal. Follow the ﬁtting instructions supplied

with good quality plugs. Recommended fuse for 230V

U.K. plug: 13 A.

Fitting a Mains Plug to 115 V Units

(U.K. and Ireland Only)

• The plug ﬁtted should comply with BS EN 60309

(BS4343), 32 Amps.

WARNING: Always ensure that the cable

clamp is correctly and securely ﬁtted to the sheath of

the cable.

Using an Extension Cable

An extension cord should not be used unless absolutely

if an extension cable is required, use an approved 3–core

extension cable suitable for the power input of this tool

(see Technical Data).The minimum conductor size is

1.5 mm2; the maximum length is 30m.

When using a cable reel, always unwind the cable

completely.

PACKAGE CONTENT

1 x Router

1 x Collet 1/2” UK & ROI (12mm EU)

1 x Parallel fence

2 x Guide rods

1 x Guide bush (30mm)

1 x 22 mm wrench

1 x SA Dust extraction tube

1 x Remote Switch Box (T14 only)

1 x Instruction manual

1 x Fine height adjuster (T14 only)

• Check for damage to the tool, parts or accessories

which may have occurred during transport.

• Take the time to thoroughly read and understand this

manual prior to operation.

MARKINGS ON TOOL

The following pictograms are shown on the tool:

Read instruction manual before use.

EN - T12/T14

-12-

Wear ear protection.

Wear eye protection.

Visible radiation. Do not stare into light.

Date Code Position - (Fig. A)

The date code (56) , which also includes the year of

manufacture, is printed into the housing.

Example:

2021 XX XX

Year and Week of Manufacture

Description - (Fig. A)

WARNING: Never modify the power tool or

any part of it. Damage or personal injury could result.

1. Speed control wheel

2. Main handles

3. On/off trigger switch

4. Thumb wheel

5. Height stop rod

6. Plunge lock lever

7. Quick release button

8. Spindle lock button

9. Collet assembly

10. Base plate

11. Multiple position turret stop

12. Depth stop bar

13. 22 mm wrench

14. Quick zero reset ring

15. Quick height adjuster lock

16. Quick height adjuster

17. Pointer

18. Fine adjuster

19. Fine zero reset ring

20. Lock on button switch

Intended Use

The T12 and T14 routers have been designed for

professional heavy duty routing of wood, wood based

materials and plastics.

These routers are intended for routing grooves, edges,

proﬁles and slots as well as copy routing.

DO NOT use under wet conditions or in the presence of

ﬂammable liquids or gases.

The T12 and T14 are professional power tools.

The T14 is designed so that it can be installed into a

router table. The router may only be installed in tables

that meet the legal safety requirements for router tables.

DO NOT let children come into contact with the tool.

Supervision is required when inexperienced operators

use this tool.

• Young children and the inﬁrm. This appliance is not

intended for use by young children or inﬁrm persons

without supervision.

• This product is not intended for use by persons

(including children) suffering from diminished physical,

sensory or mental abilities; lack of experience,

knowledge or skills unless they are supervised by a

person responsible for their safety. Children should

never be left alone with this product.

CAUTION: Before operating any of the

controls, read the following sections.

Plunge Lock Lever - (Fig. B)

The plunge lock lever (6) allows you to stop the working

bit at a speciﬁed height.

1. Press down the plunge lock lever (6) until you hear an

audible “Click” when you want to lower the router bit into

the workpiece.

2. You can lower the unit until it reaches your preset

stop.

3. To lock the tool in place along its vertical travel, press

quick release button (7).

Collets - (Fig. C)

WARNING: Projectile hazard. Only use bits

with shanks that match the installed collet. Smaller

shank bits will not be secure and could become loose

during operation.

CAUTION: Never tighten the collet without

ﬁrst installing a router bit in it. Tightening an empty collet,

even by hand, can damage the collet.

A collet is included with this router.

• 12 mm: Europe

• 1/2”: UK & Eire

1. To change collets (35), unscrew the collet assembly

(9)

2. Sharply pull the old collet out of the collet nut (45) and

insert the new collet (35).

3. Push ﬁrmly so that the new collet snaps past the

retainer spring in the collet nut.

Multiple Position Turret Stop - (Fig. E)

WARNING: Do not change the turret stop

while the router is running. This will place your hands too

near the cutter head.

The turret stop (11) limits the downward distance that

the tool can be plunged. It consists of three screws of

EN - T12/T14

-13-

different lengths that serve to deﬁne the depth of cut by

limiting the travel of the depth stop bar (12).

1. Routing depth can be set by selecting the screw of the

appropriate length on the turret.

2. The turret is rotatable with detent stops to properly

align the screws.

3. It is the interaction of the depth stop bar and the turret

stop that determine the routing depth.

4. If none of the provided screws seems close to the

desired height each can be adjusted by loosening the

hex nut at the bottom and then turning the screw either

in or out to make it the proper length. After adjusting this

screw be sure to tighten the hex nut at the bottom with

the an 8 mm wrench (55).

5. Refer to section Setting the Routing Depth for

instructions on how to use the turret stop in an actual

operation.

Height Stop Rod and Height Stop

Thumb Wheel - (Fig. G & Ga)

T12 Height Stop Rod and Height Stop Thumb Wheel

(Fig. G)

The height stop rod (5) and thumb wheel (4) limit how

high the unit can travel up the rails. The system is

adjustable to limit the rise of the plunge regardless of

the position of the plunge release lever to full up where

the bottom of the collet is 80 mm (3 5/32”) above the

workpiece.

NOTE: It is easier to move the height stop thumb wheel

UP if the plunge release lever is locked and easier to

move the thumb wheel down if the unit is ﬁrst moved

down by releasing the plunge release lever and then

tightening it.

ASSEMBLY AND ADJUSTMENTS

WARNING: To reduce the risk of serious

personal injury, turn tool off and disconnect

tool from power source before making any

adjustments or removing/ installing attachments

or accessories. An accidental start-up can cause

injury.

Installing and Removing a Cutter

- (Fig. C, F)

WARNING: Do not tighten the collet without

a cutter ﬁtted.

WARNING: Always use cutters with shanks

which match the diameter of the collet.

WARNING: Do not use cutters larger than 50

mm (2”) unless the router is ﬁtted in a router table.

CAUTION: Care should be taken when

removing cutter to avoid cuts to ﬁngers.

Installing a Cutter

1. Insert at least three fourths of the shank length of the

cutter into the collet assembly (9).

2. Press the spindle lock (8) forward until the router

spindle is locked.

NOTE: You may need to turn the spindle slightly to

engage it.

3. Turn the collet nut (45) counter clockwise with the

supplied 22 mm wrench (13) to tighten it.

Removing a Cutter

1. Press the spindle lock button (8) forward until the

router spindle is lock.

2. Turn the collet nut (9) clockwise with the supplied 22

mm wrench (13) to loosen.

3. Keep turning the wrench until the collet nut tightens

and then loosens again. This is the fail safe mechanism

releasing the collet.

4. The cutter should now slide out.

NOTE: Each time you ﬁnish using a cutter, remove it and

store it in a safe place.

Fine Height Adjuster - (Fig. A, D, E)

CAUTION: Ensure that the plunge locking

lever is unlocked. Never use unnecessary force to rotate

the ﬁne height adjuster mechanism.

CAUTION: DO NOT remove the screw on

hex nuts.

The ﬁne height adjuster can be used in portable mode or

when the router is held inside a table.

Adjusting the Depth of Cut

- (Fig. A, D, E)

Your router is equipped with a high precision depth

adjustment system including a zero reset ring for both

the quick height adjuster and the ﬁne height adjuster.

Quick adjustment Using the

graduation with Zero Reset Ring

1. Loosen the depth stop quick height adjuster lock (15).

EN - T12/T14

-14-

2. Unlock the plunge limiter by pushing the release lever

(6) down.

3. Lower the router carriage until the cutter is in contact

with the workpiece.

4. Press the quick locking button (7).

5. Set the quick height adjuster (16) to zero and reset

the ﬁne adjust reset ring (19) to zero. The depth stop bar

(12) must be in contact with the turret stop (11).

6. Adjust the depth of cut using the quick height adjuster

(16) and the corresponding graduation. The adjusted

depth of cut is indicated by the pointer (17).

7.Tighten the quick height adjuster lock (15).

Fine Adjustment

When not using a depth template, or if the depth of cut

needs readjustment, it is recommended to use the ﬁne

height adjuster (18).

1. Adjust the depth of cut as described in Adjusting the

Depth of Cut.

2. Set the ﬁne height adjuster to zero using the ﬁne zero

reset ring (19).

3. Rotate the ﬁne height adjuster (18) to the required

position: one turn corresponds to approximately 1 mm

and 1 mark to 0.1 mm.

Fitting Template Guide Bush and

Inner Plate - (Fig. H)

The routers have a unique built-in line up system for the

template guide bush. This system ensures that the guide

bush is exactly concentric to the router cutter to ensure

accurate work.

1. Turn the router upside down.

2. Fit inner plate (58) into the recess in the router base

plate (10). For T12 the bushes on the inner plate must be

towards the router motor. For T14 the raised side of the

inner plate must be away from router base. Loosely ﬁt

the two pan head machine screws (59) through the inner

plate and into the tapped holes. DO NOT TIGHTEN

SCREWS.

3. Fit the 30mm template guide bush (24) to the inner

plate (58). Fit guide bush with the two M5 countersink

machine screws (25). Tighten these screws.

4. The line-up pin (60) is stepped for 12mm and 1/2”

collet (9) sizes. (For the 1/2” collet simply push the line-

up pin further down into the 1/2” collet).

5. Fit line up pin (60) into the 1/2” collet (9) (or 12mm

depending on the size ﬁtted) in the router, lightly tighten

collet nut to hold the line up pin (60).

6. Release plunge lever and gently depress base until

line up pin (60) projects through the 30mm guide bush

(24).

7. Once in line, tighten the pan head machine screws

(59) with a ﬂat screwdriver.

Fitting the Parallel Fence - (Fig. I, J)

1. Fit the guide rod (26) to the router base (10).

2. Slide the parallel fence (27) over the rods.

3. Tighten the wing bolts (28) temporarily.

Adjusting the Parallel Fence -

- (Fig. A, I, J)

1. Draw a cutting line on the material.

2. Lower the router carriage until the cutter is in contact

with the workpiece.

3. Push quick release button (7) and limit the carriage

return using the thumb wheel (4).

4. Position the router on the cutting line.

5. Slide the parallel fence (27) against the workpiece and

tighten the wing bolts (28).

6. Adjust the parallel fence using the ﬁne adjustment

knob (29). The outer cutting edge of the cutter must

coincide with the cutting line.

7. If required, loosen the screws (30) and adjust the

strips (31) to obtain the desired guiding length.

Dust Extraction - (Fig. A, K, P)

Dust from materials such as lead containing coatings

and some wood types, can be harmful to one’s health.

Breathing in the dust can cause allergic reactions and/or

lead to respiratory infections of the user or bystanders.

Certain dust, such as oak or beech dust, is considered

carcinogenic, especially in connection with wood

treatment additives.

Observe the relevant regulations in your country for the

materials to be worked.

The vacuum cleaner must be suitable for the material

being worked.

When vacuuming dry dust that is especially detrimental

to health or carcinogenic, use dust class M vacuum

cleaner.

Connecting Dust Extraction Adaptor

- (Fig. K)

The dust extraction adaptor consists of a main section

(32), a cover (33), an extraction tube adaptor (34) , one

extraction tube screw (37), two base screws (52) and

two nuts (36) .

1. Slide the cover (33) onto the main section (32) until it

clicks into place.

2. Place the main section (32) on the base and secure

with two screws (52) and nuts (36).

EN - T12/T14

-15-

3. Remove screw (37) from the top of the router and use

this screw to assemble the extraction tube adaptor (34)

to the router.

Connecting Dust Extractor Hose

- (Fig. P)

WARNING: Risk of dust inhalation. To reduce

the risk of personal injury, ALWAYS wear an approved

dust mask.

WARNING: ALWAYS use a vacuum extractor

designed in compliance with the applicable directives

regarding dust emission when sawing wood. Vacuum

hoses of most common vacuum cleaners will ﬁt directly

into the dust extraction outlet.

Connect a dust extractor hose (38) to the extraction

tube adaptor (34).

A dust extraction tube adaptor (34) is supplied with your

tool. Vacuum hoses on most vacuum extractors will ﬁt

directly into the dust extraction spout.

NOTE: When using dust extraction, be sure that the

dust extractor is out of the way and secure so that it

will not tip over or interfere with the router or workpiece.

The dust extractor hose and power cord must also be

positioned so that they do not interfere with the router or

workpiece. If the dust extractor or dust extractor hose

cannot be positioned properly, it should be removed.

OPERATION

Instructions for Use

WARNING: Always observe the safety

instructions and applicable regulations.

WARNING: To reduce the risk of serious

personal injury, turn tool off and disconnect

tool from power source before making any

adjustments or removing/ installing attachments

or accessories. An accidental start-up can cause

injury.

Proper Hand Position - (Fig. O)

WARNING: To reduce the risk of serious

personal injury,

ALWAYS use proper hand position as shown

WARNING: To reduce the risk of serious

personal injury,

ALWAYS hold securely in anticipation of a sudden

reaction.

Proper hand position requires both hands on the main

handles (2).

Using the Router - (Fig. A, L)

CAUTION: Turn the router on before plunging

the cutter head into the workpiece.

CAUTION:

• Excessive cutting may cause overload of the motor or

difﬁculty in controlling the tool, the depth of cut should

not be more than 15 mm (19/32”) at a pass when

cutting grooves with a 8 mm (5/16”) diameter bit.

• When cutting grooves with a 20 mm (25/32”) diamter

bit, the depth of cut should not be more than 5 mm

(3/16”) at a pass.

• For extra deep grooving, make two or three passes

with progressively deeper bit settings.

CAUTION: After long periods of working at

low speeds, allow the machine to cool down by running

it for three minutes at maximum speed, with no load.

All common routing tasks can be performed with the

plunge cut router on all types of wood and plastic:

• Grooving

• Rebating

• Recessing

• Veining

• Proﬁling

To prevent overload of the tool by using the wrong speed

selection, follow the recommended settings below:

MATERIAL CUTTER DIAMETER

10 – 30 mm 30 – 50 mm 50 – 86* mm

SPEED SELECTION

Hardwood 7 - 5 6 - 2 5 - 2

Softwood 7 - 6 7 - 5 5 - 2

Chipboard

Faced

7 - 6 7 - 4 n / a

Plastic 7 - 5 7 - 4 n / a

* Do not use cutters larger than 50 mm (2”) unless the

router is ﬁtted in a router table.

NOTE: Only carbide tipped cutters should be used on

panels faced with plastic laminates. The hard laminates

will quickly dull steel cutters.

EN - T12/T14

-16-

NOTE: For better plunge sliding movement, frequently

clean the columns of dust or debris. If the plunging

movement is not moving as smooth as desired, lubricate

the columns with a dry Teﬂon lubricant.

1. After setting the cutting depth as described, locate the

router such that the bit is directly over the place you will

be cutting.

2. With the router running, lower the unit smoothly down

into the workpiece. DO NOT JAM THE ROUTER

DOWN.

3. When the tool reaches the pre set depth, push the

quick release button (7) to lock.

4. When you have ﬁnished routing, push the plunge

lock lever (6) to unlock and let the spring lift the router

directly out of the workpiece.

5. Always feed the router opposite to the direction in

which the cutter is rotating. Refer to Fig. L.

On/Off Trigger Switch - (Fig. A)

WARNING: To reduce the risk of serious

personal injury, turn unit off and disconnect it from power

source before making any adjustments or removing/

installing attachments or accessories. An accidental

start-up can cause injury.

1. To turn the unit on, squeeze the on/off trigger switch

(3). Continue to squeeze the trigger switch or press the

lock on button switch (20) for continuous running.

2. To turn the unit off:

a. If lock on trigger is engage, release the lock on button

by squeezing and releasing trigger.

b. If the lock on switch is not engaged, fully release the

trigger.

Variable Speed Dial - (Fig. A)

WARNING: If the speed control ceases

to operate, or is intermittent, stop using the tool

immediately. Please contact Trend Tool Technology Ltd

or authorized service facility for repair.

NOTICE: The router is equipped with electronics to

monitor and maintain the speed of the tool while cutting.

In low and medium speed operation, the speed control

prevents the motor speed from decreasing. If you expect

to hear a speed change and continue to load the motor,

you could damage the motor by overheating. Reduce

the depth of cut and/or slow the feed rate to prevent tool

damage.

Refer to the Speed Selection Chart to choose a router

speed. Turn the speed dial (1) to control router speed.

The speed is variable from 9000 to 22000 rpm using the

speed dial (1).

1. Turn the speed dial to the required position. The dial is

numbered from 1 –7 and corresponds to router speeds

of 9000 rpm to 22000 rpm.

2. Use the slower settings for large diameter cutters and

the faster settings for small diameter cutters.

3. The correct setting will also depend on the density of

the material, depth of cut and feed speed of the router.

NOTE: A noticeable loss of motor rpm means motor

overload

SPEED SELECTION CHART

DIAL SETTING APPROXIMATE RPM

1 9000

2 11000

3 13000

4 15000

5 18000

6 20000

7 22000

The speeds in this chart are approximate and are for

reference only. Your router may not produce the exact

speed listed for the dial setting.

WARNING: Always follow the bit

manufacturer’s speed recommendations as some

bit designs require speciﬁc speeds for safety or

performance.

If you are unsure of the proper speed or are experiencing

any type of problem, contact the bit manufacturer.

LED Worklight - (Fig. F)

CAUTION: Do not stare into worklight.

Serious eye injury could result.

Two LED worklights (57) are located next to the collet

assembly (9).

1. The worklights (57) will constantly illuminate when the

router is connected to the mains power supply.

2. To switch off the worklights the router must be

disconnected from mains power supply.

NOTE: The worklight is for lighting the immediate work

surface and is not intended to be used as a ﬂashlight.

Setting Plunge Lock System - (Fig. B)

The plunge is fully automatically locking for all cuts. For

heavy cut operations, ensure to push the lever towards

the tool body. The plunge lock lever (6) position is set at

EN - T12/T14

-17-

the factory so the lever does not touch the motor body,

if the plunge lock lever begins to hit the body when the

quick release lever is pushed, readjust the locking lever

position as follows:

1. Push in quick release button (7). The plunge lever lock

will unlock automatically.

2. Using a Torx 20 star bit (39), loosen the shoulder

screw (54) on the plunge lock lever (6) with six

counterclockwise turns. Do not fully remove.

3. Lift the plunge lock lever, rotate and reposition the

plunge lock lever at position 2 (at eleven o’clock).

4. Tighten the shoulder screw.

5. If after setting to position 2 sliding is not correct,

repeat steps 1 to 3 and reposition the lock lever at

position 1. Tighten the shoulder screw.

Moulding Natural Timbers

WARNING: When routing always lock the

plunge locking lever.

When edge moulding natural timbers, always mould the

end grain ﬁrst, followed by the long grain. This ensures

that if there is breakout, it will be removed when the long

grain is routed.

Setting the Routing Depth - (Fig. D, E)

1. Place the router with cutter ﬁtted on to the workpiece.

2. Set the multiple position turret stop (11) as required.

3. Loosen the knob quick adjustment (15) securing the

depth stop (12).

4. Push down the plunging lock lever (6) to start

plunging.

5. Lower the router slowly until the cutter touches the

workpiece and secure it in place by pushing quick

release button (7).

6. Rotate the quick height adjuster (16) until the depth

stop bar (12) touches multiple turret stop (13) . Secure

in position by tightening the quick height adjuster lock

(15).

7. If the depth of cut needs re adjustment, it is

recommended to use quick depth adjuster (16) for gross

settings, or the ﬁne height adjuster for accurate settings.

8. Adjust the depth of cut using the ﬁne height adjuster

(18)

NOTE: : One turn of the ﬁne height adjuster (18)

corresponds to 1 mm (3/64”), one turn of the quick

height adjuster (15) corresponds to 40 mm (1 1/2”)

9. Read the depth of cut using the quick zero reset ring

(14) and ﬁne zero reset ring (19).

10. The distance between the top of the revolving depth

stop and the bottom of the depth stop is the required

depth of cut.

11. The rotating turret stop screws (11) can be used

for setting up to three depths of cut. The height can

be adjusted using a ﬂat screwdriver and a 8mm (5/16”)

wrench.

NOTE: By rotating the turret stop, three depth settings

can be quickly made.

Fine Height Adjuster - (Fig. D)

This router has a built in ﬁne height adjuster. This should

be used when ﬁne height adjustment of the cutter is

required. This is especially recommended when using

dovetail jigs or router tables.

Direction Of Feed - (Fig. L)

WARNING: Avoid climb-cutting (cutting in

direction opposite than shown in Fig. L). Climb-cutting

increases the chance for loss of control resulting in

possible injury. When climb-cutting is required (backing

around a corner), exercise extreme caution to maintain

control of router. Make smaller cuts and remove minimal

material with each pass.

The direction of feed is very important when routing and

can make the difference between a successful job and

a ruined project. Fig. L show proper direction of feed for

most cuts.

1. When routing along an edge, the direction of the

router travel should be against that of the rotation of

the cutter. This will create the correct cutting action

and prevent the cutter from snatching. It will also pull

the router towards the workpiece and the side fence or

guide bearing will be less likely to wander from the edge

of the workpiece.

Feed Speed

The speed at which the cutter is fed into the wood must

not be too fast that the motor slows down, or too slow

that the cutter leaves burn marks on the face of the

wood.

NOTE: Practice judging the speed by listening to the

sound of the motor when routing.

Sequence of Plunging

WARNING: When routing always lock the

plunge locking lever.

1. Plunge down and lock the motor carriage, by pushing

quick release button (7).

2. Perform the desired routing operation.

3. Push down the plunge lock lever (6) and the motor

carriage returns to the normal position.

EN - T12/T14

-18-

Using a Side Fence - (Fig. M)

CAUTION: Ensure working position is

comfortable and at a suitable working height.

1. Ensure the wing bolts (28) are fully released. Slide the

guide rods (26) into the routing base (10) and tighten

the wing bolts.

2. Adjust the fence ﬁne adjustment knob (29) to the

required distance and clamp in place with the wing bolts

(28).

3. Then lower the cutter height until the cutter is just

above the workpiece.

4. Fine adjustments are possible by loosening the wing

bolt (28) and adjusting the side fence ﬁne adjustment

knob (29).

5. Tighten the wing bolt (28) to secure the position.

NOTE: One revolution of the side fence ﬁne adjustment

knob (29) equals 3/64” (1.0 mm) of side feed.

6. Lower the cutter onto the workpiece and set the cutter

height by to the required distance. Refer to Setting the

Router Depth.

7. Switch the router on and after the cutter reaches full

speed, gently lower the cutter into the workpiece and

lock the plunge.

8. Feed along the workpiece, keeping sideways pressure

to ensure the side fence does not wander away from the

workpiece edge and downward pressure on the inside

hand to prevent the router from tipping.

9. When ﬁnished, raise the router, secure with the plunge

locking lever (6) and switch the router off.

NOTE: When starting the cut, keep the pressure on the

front cheek until the back cheek contacts the workpiece

edge.

NOTE: At the end of the cut, keep pressure on the

back cheek until the cut is ﬁnished. This will prevent the

router cutter swinging in at the end of the workpiece and

nipping the corner.

Side Fence Routing - (Fig. I, J)

The side fence is used to guide the router when

moulding, edge proﬁling or rebating the edge of a

workpiece or when routing grooves and slots in the

center of the workpiece, parallel to the edge.

The edge of the workpiece must be straight and true.

The strips (31) are adjustable and should be set ideally

with a 1/8” (3 mm) gap each side of the cutter.

Guiding Off a Batten

Where an edge guide cannot be used, it is also possible

to guide the router along a batten clamped across the

workpiece (with an overhang at both ends).

Freehand Routing

WARNING: Make shallow cuts only! Use

cutters with a max. diameter of 12mm.

Your router can also be used without any sort of guide,

e.g. for signwriting or creative work.

Table Mode - (Fig. Q)

(T14 ONLY)

WARNING: Before T14 is installed into

the router table, check that the router table meets

all of the legal safety requirements for router

tables. Read all safety warnings, instructions,

and speciﬁcations provided with the router table.

Failure to follow all instructions and safety rules may

result in electric shock, ﬁre and/or serious injury.

WARNING: To reduce the risk of serious

personal injury, turn unit off and disconnect

it from power source before making any

adjustments or removing/ installing attachments

or accessories. An accidental start-up can cause

injury.

WARNING: Do not use the T14EK as

a handheld router if the power switch box is

connected.

CAUTION: If there is dust inside the

power switch socket, clean it out before using the

power switch box.

1. To connect the power switch box (41) to the router,

disconnect the tool from its power source.

2. Attach the power switch box (41) to the workbench

in a position easily accessible by hand and where

unintentional switching on is prevented.

NOTE: The external switch can be secured to the router

table with the four mounting holes (42).

3. The cable must be installed and fastened in such a

way that it cannot be squeezed or touch sharp edges.

4. Push in on the lock button (43) located on the left side

handle (44) with a pen or a small screwdriver to unlock

the handle cap (40).

NOTE: If there is dust inside the power switch socket,

clean it out before using the power switch box.

5. Keep pushing the lock button (43) in and rotate the

handle cap (40) to access the power switch socket (46).

6. Ensure the paddle switch of the power switch box is

in the off position before connecting to the power switch

socket.

EN - T12/T14

-19-

7. Connect power switch box plug (47) to the power

switch socket (46).

8. Thread the ring nut (48) of power switch box plug

(47) to the power switch socket (46) to lock it securely

in place.

9. Attach the plunge router under the workbench, as

required per your application or the instruction for the

router table switch box (41).

10. Plug the tool back into its power source. The router

can now switched on and off by acting on paddle (49)

on the power

11. Pull out the paddle (49) to start the tool and push in

the paddle to switch it off.

Fitting the T14 Fine Height Adjuster

- (Fig. S1)

The ﬁne height adjuster (Quick Raiser) (61) for the T14

can be used portably or when the router is held inverted

in a table. If a suitable size access hole is drilled into

the router table top, the height adjustment can also be

adjusted from above the table top.

To set up for ﬁne height adjustment:

1. Plunge router and lock lever down.

2. Rotate the knurled nut (4) down the stud until it is

close to the router casting forks (62).

3. Align the base of the knurled nut (4) so that it will

locate in the forks (62).

4. Release plunge locking lever.

CAUTION: DO NOT use a powered drill

to drive the T14 Quick Raiser assembly. Only use the

supplied handle. Ensure that the plunge locking lever

is unlocked. Never use unnecessary force to rotate the

Quick Raiser mechanism. Do not undo Torx® screw on

hex nuts.

Using the T14 Without Fine Height

Adjuster - (Fig. S2)

In portable use the knurled nut (4) should be wound to

the top of the stud and hand tightened against the hex

cap. The base of the knurled nut (4) should be aligned

with the forks (62) in the router casing.

CAUTION: In normal plunge mode, ensure

the base of the knurled nut is aligned correctly with the

forks of the lower motor housing. This will enable the

cutter to retract into the base safely.

For Portable Use:

1. Place the ﬁne height adjuster handle (61) onto the top

threaded spindle hex nut (51).

2. Rotate handle clockwise to raise motor body and

reduce cutter depth.

3. Rotate handle anti-clockwise to lower motor body and

increase cutter depth.

For Router Table Use - (Fig. S3)

1. Ensure router is ﬁtted into the router table, see

opposite page.

2. Place ﬁne height adjuster handle (61) through router

table cutter hole onto bottom threaded spindle hex nut

(64).

3. Rotate handle clockwise to raise motor body and raise

cutter height.

4. Rotate handle anti-clockwise to lower motor body and

lower cutter height.

One revolution corresponds to 1.5mm. The height

adjuster handle dial (63) can be reset to zero.

Prior to Operation

1. Check that the cutter is correctly installed in the collet.

2. Set the cutting depth.

3. Connect a dust extractor.

4. Make sure the plunge limiter is always locked before

switching on.

Routing with Pilot Cutters - (Fig. R)

Where a parallel guide or guide bush are inappropriate,

it is possible to use pilot cutters (50) for cutting shaped

edges.

These include collets (6 – 12.7 mm), a height adjusting

tool and router table for use in inverted position, ﬁnger

jointing tools for dovetail and ﬁnger jointing jigs, dovetail

jointing templates, adjustable guide bush holder and

guide bushes and guide rails in various lengths.

Base Mounting Points for Accessories

- (Fig. N)

This router has three threaded holes (53) built into the

base that allows it to attach to other accessories.

MAINTENANCE

Your power tool has been designed to operate over a

long period of time with a minimum of maintenance.

Continuous satisfactory operation depends upon proper

tool care and regular cleaning.

EN - T12/T14

-20-

WARNING: To reduce the risk of serious

personal injury, turn tool off and disconnect

tool from power source before making any

adjustments or removing/ installing attachments

or accessories. An accidental start-up can cause

injury.

Repairs

WARNING: To assure product SAFETY

and RELIABILITY,repairs, maintenance and adjustment

(including power cord repairs, and brush inspection and

replacement, when applicable) should be performed by a

Trend service center or a Trend authorized service center.

Always use identical replacement parts.

Lubrication

• Your power tool requires no additional lubrication.

Cleaning

WARNING: Blow dirt and dust out of

the main housing with dry air as often as dirt is seen

collecting in and around the air vents. Wear approved

eye protection and approved dust mask when

performing this procedure.

WARNING: Never use solvents or other

harsh chemicals for cleaning the non-metallic parts of

the tool. These chemicals may weaken the materials

used in these parts. Use a cloth dampened only with

water and mild soap. Never let any liquid get inside the

tool; never immerse any part of the tool into a liquid.

Optional Accessories

WARNING: Since accessories, other than

those offered by Trend Tool Technology Ltd, have not

been tested with this product, use of such accessories

with this tool could be hazardous. To reduce the risk of

injury, only Trend Tool Technology Ltd recommended

accessories should be used with this product.

Consult your dealer for further information on the

appropriate accessories.

Storage

• After use return the tool to its storage box.

ENVIRONMENTAL PROTECTION

Recycle raw materials instead of disposing as

waste.

Accessories and packaging should be sorted for

environmental-friendly recycling.

Separate collection. This product must not be disposed

of with normal household waste.

Household User

Local regulations may provide for separate collection

of electrical products from the household, at municipal

waste sites or by retailer when you purchase a new

product. Please call Trend Customer Services for advice

as to how to dispose of unwanted Trend electrical

products in an environmentally safe way or visit

www.trend-uk.com

Business Users

Please call Trend Customer Services for disposal of

unwanted Trend electrical products.

GUARANTEE

The unit carries a manufacturers guarantee in

accordance with the conditions on the enclosed

guarantee card.

For the location of your nearest Trend Service Agent,

please call Trend Customer Services or see our stockist

locator at www.trend-uk.com

Sidan laddas ...

Trend T12 Användarmanual

Denna manual är också lämplig för

Trend T12 Användarmanual

på andra språk

Relaterade papper

Andra dokument