Metz mecablitz 64 AF-1 digital Canon GB/S/SF/DK/LV Användarmanual

Kategori
Kameran blinkar
Typ
Användarmanual
www.metz-mecatech.de
mecablitz 64 AF-1 digital
für / for Canon-Digitalkameras
Operating Instructions, Bruksanvisning, Käyttöohje,
Brugervejledning, Ekspluatācijas instrukcija
14/36/04
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1 Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2 Dedicated flash functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
3 Preparing the flash unit for use . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
3.1 Mounting the flash unit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
3.2 Power supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
3.3 Switching the flash unit on and off. . . . . . . . . . . . . . . . . . . . . . . . 8
3.4 The selection menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
3.5 INFO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3.6 Auto OFF for the flash unit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
4 LED displays on the flash unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
4.1 Flash readiness indication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
4.2 Correct exposure indication . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
5 Information in Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
5.1 Display of the flash mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
5.2 Range display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
6 Displays in the camera viewfinder . . . . . . . . . . . . . . . . . . . . . . . . 14
7 Flash modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
7.1 E TTL- and E TTL II - flash mode . . . . . . . . . . . . . . . . . . . . . . . . . . 14
7.2 Automatic E TTL Fill-in flash mode. . . . . . . . . . . . . . . . . . . . . . . 15
7.3 Manual flash mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
7.4 Automatic high-speed synchronisation (HSS) . . . . . . . . . . . . . 17
7.5 Automatic flash mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
7.6 Strobe flash mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
8 Manual flash exposure correction . . . . . . . . . . . . . . . . . . . . . . . . 20
9 Special functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
9.1 Motor zoom reflector („Zoom“) . . . . . . . . . . . . . . . . . . . . . . . . . 21
10 Cordless flash mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
10.1 Remote master mode settings . . . . . . . . . . . . . . . . . . . . . . . . . 24
10.1.1 Remote master mode settings . . . . . . . . . . . . . . . . . . . . . . . 24
10.1.2 Setting the flash mode on the master flash unit . . . . . . . . . 25
10.1.3 Setting the exposure correction (EV) in ETTL mode
on the master flash unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
10.1.4 Lighting conditions (RATIO) for the flash groups settings
on the master flash unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
10.1.4.1 Lighting conditions for flash groups A + B settings
on the master flash unit. . . . . . . . . . . . . . . . . . . . . . . . . . . 26
10.1.4.2 Exposure correction (EV) for flash group C settings
on the master flash unit. . . . . . . . . . . . . . . . . . . . . . . . . . . 26
10.1.5 Partial light output (M) in M-mode settings
on the master flash unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
10.1.6 Remote channel settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
10.2 Remote slave flash mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
10.2.1 Remote slave flash mode settings . . . . . . . . . . . . . . . . . . . . 28
10.2.2 Setting the slave channel . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
10.2.3 Setting the slave group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
10.3 Testing remote flash mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
10.4 SERVO mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
10.4.1 Setting SERVO flash mode. . . . . . . . . . . . . . . . . . . . . . . . . . . 30
10.4.2 Pre-flash suppression or synchronisation settings . . . . . . . 31
10.4.3 Servo mode partial light output settings . . . . . . . . . . . . . . . 31
10.4.4 Learn function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
10.4.5 Switching-off SERVO flash mode . . . . . . . . . . . . . . . . . . . . . 33
11 OPTION menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
11.1 Synchronisation on the second curtain (REAR). . . . . . . . . . . . 33
11.2 RAPID mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
11.3 Secondary reflector (SUB-REFL.) . . . . . . . . . . . . . . . . . . . . . . . 35
11.4 Modelling light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
11.5 Zoom Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
11.5.1 Extended Zoom Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
2
k
Introduction
Thank you for choosing a Metz product. We are delighted to welco-
me you as a customer.
You will of course be impatient to start using the flash unit.
However, it is worthwhile reading the operating instructions and
learning how to use the unit correctly.
This flash unit is suited for:
• Digital Canon cameras with E-TTL and
E-TTL-II - flash metering.
This flash unit is not suited for other brands of cameras.
Take a look at the diagrams at the end of the manual.
Declaration
Tip, note
Attention - Extremely important safety
information!
Proper Use
This flash unit is intended solely for taking pictures of motifs in the
photographic field. It may be operated only with the accessories
described in this instruction manual or the accessories approved by
Metz.The flash unit may not be used for any purpose other than that
described above.
+
11.5.2 SPOT zoom mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
11.5.3 STANDARD zoom mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
11.6 Shooting format adjustment (Zoom-Size) . . . . . . . . . . . . . . . . 37
11.7 AF-BEAM (AF auxiliary light) . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
11.8 Range display in m or ft . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
11.9 Flash Bracketing Series (FLASH BRACK.) . . . . . . . . . . . . . . . . . 39
11.10 Beep function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
11.11 Locking / unlocking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
11.12 Connecting a power pack (accessory) . . . . . . . . . . . . . . . . . . 41
12 Favorite programme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
13 Flash techniques . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
13.1 Bounce flash . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
13.2 Bounce flash with a reflector card . . . . . . . . . . . . . . . . . . . . . . 43
13.3 Close-ups / macro shots. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
13.4 Flash exposure memory FE . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
14 Flash synchronisation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
14.1 Automatic flash sync speed control. . . . . . . . . . . . . . . . . . . . . 44
14.2 Normal synchronisation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
14.3 Slow synchronisation (SLOW). . . . . . . . . . . . . . . . . . . . . . . . . . 45
14.4 Synch socket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
15 Touch display settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
15.1 Brightness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
15.2 Rotation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
16 Care and maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
16.1 Firmware updates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
16.2 Conditioning the flash capacitor . . . . . . . . . . . . . . . . . . . . . . . 47
16.3 Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
17 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
18 Technical data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
19 Optional accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
3
k
1 Safety instructions
The flash unit may in no event be activat-
ed in the vicinity of inflammable gases or
liquids (petroleum, solvents etc.).
RISK OF EXPLOSIONS!
Do not flash directly into eyes from a clo-
se distance! Direct flashing into the eyes
of persons or animals can cause damage
to the retina and severe disruption of the
vision – up to and including permanent
blindness!
Never use a flash unit to photograph car,
bus, bicycle, motorbike or train drivers
while they are driving. Blinding the driver
can lead to an accident!
If the housing has been damaged in such
a way that internal components are
exposed, the flash unit may no longer be
used. Remove the batteries! Do not
touch any internal components.
HIGH VOLTAGE!
After repeated flashing, do not touch the
diffuser. Risk of burns!
Do not dismantle the flash unit!
HIGH VOLTAGE!
Repairs should only be performed by aut-
horised service personnel.
• The flash unit is exclusively designed and
authorised for use in photographic applica-
tions.
• Only use the power sources designated and
autho-rised in the operating manual!
• Do not open the batteries or short them!
• In no event the batteries be exposed to
high temperatures like direct sunlight, fire
or similar!
• Never throw flat/dead batteries onto a fire!
• Do not use any toxic batteries or recharge-
able batteries!
• Remove the used batteries immediately
from the device! Chemicals can escape
from used batteries (so-called “leaks”)
resulting in damage to the device!
• Batteries may not be recharged!
• Do not expose the flash unit to water drops
and splashes!
• Protect your flash unit from heat and high
air humidity! Do not keep it in the glove
compartment of your car!
• Rapid changes in temperature may lead to
condensation. If this occurs, allow time for
the unit to become acclimatized!
• When you activate the flash, there should
be no opaque material directly in front of or
on the reflector cover (flash window). The
intense energy emissions can otherwise
lead to scorching or spotting of the material
and/or the reflector cover.
4
k
• After a series of flashes with full power and
short intervals, a pause of at least 3 minu-
tes must be observed after each series of
20 flashes! !
• When taking a series of flash shots at full
light output and with rapid recycling times,
and with zoom positions of 35 mm and
less, the diffuser heats up, due to the high
level of thermal energy.
• This flash unit may be used in combination
with a camera-integrated flash only if the
flash can be folded out completely.
2 Dedicated flash functions
Dedicated flash functions are flash functions
that have been specially adapted to a given
camera system. Depending on the type of
camera, different flash functions are supported.
• Flash-ready indication in camera viewfin-
der/camera display.
• Automatic flash sync speed control.
• Automatic ETTL fill-in flash control.
• E-TTL flash mode / E-TTL II flash mode.
• Manual flash exposure correction for E-TTL /
E-TTL II.
• Flash exposure storage FE with E-TTL /
E-TTL II.
• 1st or 2nd curtain synchronisation (REAR).
• Automatic high speed synchronisation
(HSS) with E-TTL / E-TTL II and M.
• Automatic motor zoom control.
• Extended zoom mode.
• AF measuring beam control.
• Automatic flash range indication.
• Programmed auto flash mode (AUTO
FLASH).
• Wireless Canon E-TTL remote flash mode.
• Servo mode.
• Spot zoom mode.
• Wake-up function for the flash unit.
5
k
It is impossible to describe all camera types
and their individual dedicated flash functi-
ons within the scope of these instructions.
Therefore, please refer to the flash mode
description in your camera’s operating
instructions to find out which functions are
supported and which ones have to be set
manually on the camera.
Using lenses not equipped with a CPU (i.e.,
lenses without auto focus mode), results in
certain functional limitations!
3 Preparing the flash unit for use
3.1 Mounting the flash unit
Mounting the flash unit on the camera
Turn off the camera and flash before moun-
ting or removing.
• Turn the knurled nut towards the flash
unit housing as far as it will go. The locking
pin in the adapter shoe is now fully retrac-
ted into the case.
• Slide the flash unit foot completely into the
camera accessory shoe.
• Turn the knurled nut towards the camera
housing as far as it will go, clamping the
flash unit in place. If the camera does not
have a locking hole, the spring-loaded lok-
king pin retracts into the adapter case so as
not to damage the surface.
Removing the flash unit from the camera
Turn off the camera and flash before moun-
ting or dismounting.
• Turn the knurled nut towards the flash
unit housing as far as it will go.
• Remove the flash unit from the camera’s
accessory shoe.
+
+
+
6
k
3.2 Power supply
Suitable batteries/rechargeable batteries
The flash unit can be operated with any of
the following batteries:
• 4 nickel-metal-hydride batteries 1.2V, type
IEC HR6 (size AA). They have a significantly
higher capacity than NiCad batteries and
are less harmful to the environment, since
they have no cadmium.
• 4 alkaline-manganese dry cell batteries
1.5V, type IEC LR6 (size AA). Maintenance-
free power source for moderate power
requirements.
• 4 lithium batteries 1.5V, type IEC FR6 (size
AA). Maintenance-free high-capacity power
source with a low self-discharge rate.
• Power Pack with connection cable (special
accessory)
Please only use the power sources given
above. If other power sources are used, there
is a risk of damaging the flash unit.
If your flash unit is not going to be used for
an extended period of time, remove the bat-
teries.
Replacing batteries
The disposable/rechargeable batteries are
empty or used up if the recycling time (time
from the triggering of a full-power flash, e.g.
in the M mode, to the moment the flash-rea-
dy indicator lights up again) exceeds 60
seconds. In addition, the battery warning
appears on the touch display.
• Switch off the flash unit. To do this, press
the
button until all displays turn off.
• Slide the battery compartment cover
downwards and fold open.
• Insert the batteries lengthwise as indicated
by the battery symbols provided and close
the battery compartment cover .
When inserting batteries, ensure that the
polarity is correct and matches the symbols
in the battery compartment. Inserting the
batteries in the wrong direction can destroy
the flash unit! Always replace all batteries
simultaneously, and make sure that batteries
are the same brand and have the same capa-
city. Flat or dead batteries should not be dis-
posed of with ordinary household waste.
Help protect the environment, and dispose of
flat/dead batteries at the appropriate collec-
tion points.
+
7
k
3.3 Switching the flash unit on and off
Switch on the flash unit with the
button.
The start screen appears.
The flash unit always switches on after-
wards with the mode of operation that was
used last (e.g. manual flash mode M).
The button flashes red in stand-by
mode. To switch off the flash unit, press
the
button until all displays turn off.
If the flash unit will not be used for an exten-
ded period of time, we recommend that you
switch off the flash unit with the but-
ton and remove the power source (disposa-
ble/rechargeable batteries).
3.4 The selection menu
• Press the button as often as it takes
for the selection menu to appear.
The selection menu is divided into 4 sensor
buttons:
The modes of operation can be set after
pressing the button.
E TTL, chap. 7.1
E TTL HSS*, chap. 7.4
A, chap. 7.5
M, chap. 7.3
STROBO, chap. 7.6
MHSS*, chap. 7.4
REMOTE MASTER, chap. 10.1
REMOTE SLAVE, chap. 10.2
SERVO, chap. 10.4
*) only after data exchange with a camera
The flash parameters can be set after
D
MODE
D
pressing the button.
P (partial light output),
chap. 7.3, 10.1.5 and 10.4.3
EV (exposure correction),
chap. 8, 10.1.3, 10.1.4.2
ZOOM (reflector setting), chap. 9.1
N (Strobe number of flashes), chap. 7.6
f (Strobe flash frequency), chap. 7.6
F (aperture)
ISO (light sensitivity),
CHANNEL (Channel), chap. 10.1.6 , 10.2.2
GROUP (slave group), chap. 10.2.3.
RATIO (lighting conditions) chap. 10.1.4.
The displayed flash parameters are depen-
dent on the selected flash mode.
The touch display can be configured after
pressing the button, or the flash unit
can be reset to the factory setting.
BRIGHTNESS , chap. 15.1
ROTATION (rotate the screen display),
chap. 15.2
RESET, chap. 16.3
PARAMETER
SERVICE
8
k
V 1.0
MB 64AF-1
digital
CAN
MODE
PARAMETER
SERVICE
PARAMETER
O
P / EV
ZOOM
N
f (Hz)
F
ISO
CHANNEL
GROUP
RATIO
MODE
O
ETTL
ETTLHSS
A
M
MHSS
STROBO
REMOTE MASTER
REMOTE SLAVE
SERVO
SERVICE
O
BRIGHTNESS
RESET
ROTATION
The options can be set after pressing the
button.
REAR (synchronisation on the second shutter
curtain), chap. 11.1
RAPID (fast recycling times), chap. 11.2
SUB-REFL. (secondary reflector), chap. 11.2
ZOOM SIZE (shooting format adjustment),
chap. 11.6
ZOOM MODE (illumination), chap. 11.5
STANDBY (autom., unit switch-off),
chap. 3.6
MOD.LIGHT (modelling light), chap. 11.4
BEEP (acoustic signal), chap. 11.9
m / ft (metres / feet), chap. 11.8
POWERPACK (external power pack) ,
chap. 11.11
AF BEAM (AF auxiliary light),
chap. 11.7
FLASH BRACK. (flash bracketing series ,
chap. 11.9
The displayed options are dependent on the
selected flash mode.
In the menus shown on the flash unit, all
fields that have a black-gray background are
configured as sensor buttons that can be
pressed for modifications/changes in the
menu.
In the images in the user's guide, only the
sensor buttons that must be pressed for set-
ting the described function are marked in
black.
OPTION
3.5 INFO
The current settings of the flash unit can be
displayed during operation.
• Press the sensor button on the
touch display. Info appears.
- EXT (extended zoom mode) is set, (chap.
11.5.1).
- AF OFF (AF auxiliary light) is switched off,
(chap. 11.7).
- (MOD.LIGHT) is set,
(chap. 11.4).
- (beep function) is set, (chap. 11.10)
- (Channel) appears on the display,
chap. 10.1.6, 10.2.2)
- The automatic unit switch-off is set for
10 minutes (chap. 3.6).
- The temperature display increases after
intensive use.
3.6 Auto OFF for the flash unit
The flash unit is factory-set to automatically
switch to standby mode (Auto OFF) 10 minu-
tes after
• being switched on,
• a flash is fired,
• the shutter release is actuated,
• the camera’s exposure metering system is
switched off. . .
. . . switched to stand-by mode, (Auto-OFF) to
save energy and to protect the power source
from unintentional discharging. The active
2CH
i
9
OPTION
i
OPTION
O
RAPID
SUB-REFL.
ZOOM SIZE
ZOOM MODE
STANDBY
MOD. LIGHT
BEEP
m / ft
POWERPACK
AF BEAM
FLASH BRACK.
REAR
k
+
automatic unit switch-off is shown in the
INFO display.
The flash ready indicator and the indica-
tors on the LC display disappear.
The button flashes red in stand-by
mode.
The most recently used operating setting is
retained after automatic shutdown and is
immediately restored when the camera is
switched on.
The flash unit can be turned on again by
pressing the button, or by tapping on
the shutter release (wake-up function).
In slave-/ servo mode, the automatic cut-off
is not activated.
The flash unit should always be turned off
using the main switch if it is not going
to be used for an extended period!
If necessary, the Auto OFF function can be set
to occur after 1 minute of inactivity, or can be
deactivated.
The flash unit switches off completely about
1 hour after its last use.
In all operating modes, the brightness of the
screen is reduced by 50 per cent after
approx. 10 seconds to save energy. The
screen brightness is restored again whenever
a button or a symbol on the screen is pres-
sed.
D
D
Setting the automatic unit switch-off
• Switch on the flash unit with the
but-
ton. The start screen appears. The flash
unit always switches on afterwards with the
mode of operation that was used last (e.g.
manual flash mode M).
• Press the button as often as it takes
for the selection menu to appear.
• Press the sensor button on the
touch display.
• Press the sensor buttons on the
touch display and select .
• Press the sensor button on the
touch display.
• Tap the sensor button on the touch display
for the desired time. The setting is adopted
immediately.
The button flashes red in stand-by
mode.
D
OPTION
STANDBY
STANDBY
D
10
k
OPTION
OPTION
O
q
p
ZOOM MODE
STANDBY
MOD. LIGHT
STANDBY
O
OFF
1 min
10 min
4 LED displays on the flash unit
4.1 Flash readiness indication
When the flash capacitor on the flash unit is
charged, the button lights up in green,
thus indicating that the flash unit is ready.
This means that flash light can be used for
the next shot. Flash readiness is also trans-
mitted to the camera and indicated accordin-
gly in the camera's viewfinder.
If a photograph is taken before flash readi-
ness appears, then the flash unit will not be
triggered. If the camera has already switched
to flash sync speed, the shot may have the
wrong exposure (see 14.1).
4.2 Correct exposure indication
If the exposure is correct, then button
lights up in red for around 3 seconds if the
photograph has been correctly exposed in
flash modes und ; see 7.1) )
as well as automatic mode !
If there is no exposure control indication after
the shot, then the photograph was underex-
posed.
In that case, you must:
- set the next smaller f-stop (e.g. use f-stop 8
instead of 11), or
-
reduce the distance to the subject or to the
reflection surface (e.g. for indirect flashes), or
- set a higher ISO value on the camera.
Note the maximum flash range indicated on
the display of the flash unit (see 5.2).
D
ETTLHSSETTL
A
5 Information in Display
The cameras transmit the settings for ISO,
lens focal length (mm) and aperture to the
flash unit.
It calculates the maximum flash range from
the settings and their guide number.
Flash mode, range, aperture and zoom positi-
on of the reflector are displayed in the
display of the flash unit.
If the flash unit is operated without receiving
data from the camera, then the values set on
the flash unit will be shown.
Display illumination
After pressing the button on the flash
unit, or after tapping the touch display, the
display illumination will be at maximum level
for approximately 10 sec.
D
11
k
+
5.1 Display of the flash mode
The current flash mode is shown in the
display. Depending on the type of camera,
different displays are available for the selec-
ted TTL flash mode (e.g. and )
and the manual flash mode (see 7.3).
5.2 Range display
When using cameras and a lens with CPU,
the range is indicated in the display.
For this a data exchange must have occurred
between the camera and flash unit, for exam-
ple by tapping the shutter release. The range
can be displayed either in metres (m) or feet
(ft) - see 11.8).
The flash range is not displayed when . . .
- no data is transmitted from the camera.
- when the reflector head is tilted out of its
normal position (upwards or sideways).
- if the flash unit is working in REMOTE
MASTER, REMOTE SLAVE or SERVO mode.
ETTL HSSETTL
Range display in E TTL and E TTL HSS flash
modes
In the TTL flash modes and ;
see 7.1) the value for the minimum and the
maximum range of the flash unit is displayed.
The value indicated relates to subjects with a
reflection factor of 25%, which applies to
most photographic situations.
Strong deviations from this reflection factor,
as in the case of highly reflective or poorly
reflective subjects, may affect the flash range
of the flash unit.
The subject should be in the range of 40% to
70% of the maximum range. This will give the
electronics sufficient scope for compen-
sation.
To prevent overexposure, the minimum
distance to the subject shown in the display
should not be undershot.
Adjustment to the photographic situation at
hand can be achieved by, for example,
changing the aperture of the setting on the
lens.
ETTL ETTL HSS
12
k
0.8- 9.0 m
F 5,6
M-
Zoom 35
m
m
ETTL
i
EV
0.8- 9.0 m
F 5,6
M-
Zoom
35
m
m
ETTL
i
EV
Range display in manual flash mode
In manual flash mode , the distance that
must be maintained from the subject for cor-
rect flash exposure is indicated. Adjustment
to the photographic situation at hand can be
achieved by, for example, changing the aper-
ture setting on the lens or selecting a manual
partial light output level (see 7.3).
Exceeding the display range
Flash ranges of up to 99 m or 99 ft can be
shown in the display.
This display range can be exceeded in the
case of high ISO values and large aperture
openings.
An arrow or triangle after the distance value
indicates that the display range has been
exceeded.
M
13
9.0 m
F
5,6
M-
Zoom 35
m
m
M
i
P
1/1
40- 99 m u
F 1,4
M-
Zoom 200
m
m
ETTL
i
EV
k
6 Displays in the camera
viewfinder
Examples for the camera viewfinder display:
Flash symbol flashes
Command to switch on or use the flash unit.
Flash symbol is illuminated:
The flash unit is ready for use (by some
cameras).
The viewfinder in some cameras features an
incorrect exposure warning function:
the viewfinderís display for aperture value,
shutter speed (or both) flashes by over or
underexposure.
Incorrect exposure guidelines:
• overexposure: do not use the flash!
• underexposure: switch the flash on or use a
tripod and a longer exposure time.
Reasons for incorrect exposure can lay in the
various exposure and automatic program-
mes.
For information applicable to the displays in
the viewfinder of your camera model, refer to
the camera’s operating instructions.
7 Flash modes
Depending on the camera model, the follo-
wing flash modes are available:
• E TTL flash mode ( ), chap. 7.1
• Manual flash mode ( ), chap. 7.3
• Automatic high-speed synchronisation
(HSS), chap. 7.4
• Automatic flash mode ( ), chap. 7.5
• Strobe flash mode ( ), chap. 7.6
mode settings
,
chap
. 10.1
flash mode, chap. 10.2
mode,
chap
. 10.4.
The flash mode is set using the touch
display.
A data transfer between flash unit and came-
ra is necessary before setting flash mode
and , e.g. by actuating the
shutter release.
7.1 E TTL- and E TTL II - flash mode
These flash modes offer a very simple
method of obtaining very good flash shots.
Here, the exposure is measured by a sensor
in the camera. It measures the light reflected
by the subject through the lens (TTL =
"Through The Lens").
If the shot was exposed correctly, the correct
exposure indication will illuminate for about
5 seconds (see 4.2).
When taking a shot, an almost imperceptible
measurement pre-flash is triggered by the
camera prior to the actual exposure process.
REMOTE MASTER
REMOTE SLAVE
SERVO
M HSSETTLHSS
ETTL
M
A
STROBO
14
k
Setting the mode of operation
• Switch on the flash unit with the
button.
The start screen appears. Thereafter, the
flash unit always switches on with the
mode of operation that was used last
(e.g. M flash mode).
• Press the displayed mode of operation on
the touch display as many times as it takes
for the display for selecting the mode of
operation to appear.
• Press the sensor buttons on the
touch display and select the desired mode
of operation.
• Press on the selected mode of operation
that is highlighted in yellow. The setting is
adopted immediately.
• Set a suitable mode of operation on the
camera, e.g. P, Tv, Av, M etc.
• Tap the shutter release to transfer data bet-
ween the flash unit and the camera.
7.2 Automatic E TTL Fill-in flash mode
The automatic E TTL fill-in flash mode is acti-
vated by most cameras when the automatic
programme P is selected and by Vari or sub-
ject programmes during daylight (see camera
operating manual).
Fill-in flash mode overcomes troublesome
shadows and produces a more balanced
exposure between subject and background
with contre-jour shots. The camera’s compu-
ter-controlled metering system sets the most
suitable combination of shutter speed, aper-
ture and flash output.
Ensure that the contre-jour light source does
not shine directly into the lens, as this will
interfere with the camera’s TTL metering
system!
There is no setting or display for automatic
E TTL fill-in flash in the flash unit.
7.3 Manual flash mode
In the manual flash mode M, the flash unit
emits the full uncontrolled amount of light if
no partial light output has been selected. The
specific photographic situation can be taken
into account by adjusting the aperture set-
ting or by selecting a suitable manual partial
light setting.
The setting area ranges from P 1/1 to P1/256
in mode and P1/1 - 1/64 in
mode.
The display shows the distance at which the
subject is correctly lit (see 5.2).
M HSSM
15
V 1.0
MB 64AF-1
digital
CAN
7.2 m
F 5,6
M-
Zoom 35
m
m
M
i
P
1/1
MODE
O
q
p
ETTL
A
0.8- 9.0 m
F 5,6
M-
Zoom 35
m
m
ETTL
i
EV
+
k
Setting the mode of operation
• Switch on the flash unit with the
button.
The start screen appears. Thereafter, the
flash unit always switches on with the
mode of operation that was used last .
• Press the sensor button of the displayed
mode of operation on the touch display as
many times as it takes for the display for
selecting the mode of operation to appear.
• Press the sensor buttons on the
touch display and select .
• Press the sensor button on the touch
display.
• Set a suitable mode of operation on the
camera, e.g. .
• Tap the shutter release to transfer data bet-
ween the flash unit and the camera.
M
M
M
Various cameras support manual flash mode
M only in the camera's M mode (manual).
In other camera models, an error message
appears in the display and the release is
locked.
Manual partial light output levels
Partial light output can be set in manual flash
mode .
Setting procedure
• Press the sensor button for partial light out-
put on the touch display as many times as
it takes for the partial light output display
to appear.
• Press sensor buttons on the
touch display and set the desired partial
light output to 1/1, 1/2, 1/8 . . . 1/256.
• Press the sensor button on the touch
display for the selected partial light output.
The setting is immediately effective and
automatically saved.
The distance display is adjusted to the partial
light output automatically (see 5.2).
M
+
16
k
9.0 m
F 5,6
M-
Zoom 35
m
m
M
i
P
1/1
MODE
O
q
p
A
M
STROBO
0.8- 9.0 m
F 5,6
M-
Zoom 35
m
m
ETTL
i
EV
0.8- 9.0 m
F 5,6
M-
Zoom 35
m
m
ETTL
i
EV
9.0 m
F 5,6
M-
Zoom 35
m
m
M
i
P
1/1
3.1 m
F 5,6
M-
Zoom 35
m
m
M
i
P
1/8
P
O
q
p
1/1
1/1 - 1/3
P
O
q
p
1/4 - 2/3
1/8
1/8 - 1/3
7.4 Automatic high-speed synchronisa-
tion (HSS)
Various cameras support automatic high-
speed synchronisation (see the camera’s
operating instructions). This flash mode
makes it possible to use a flash unit even
with shutter speeds that are faster than the
flash sync speed.
Interesting results may by achieved in this
mode when, for example, a wide open aper-
ture (e.g., f/2.0) is used to limit the depth of
field in portrait shots taken in very bright
ambient light. The flash unit supports high-
speed synchronisation in E-TTL and M flash
modes.
For physical reasons, however, high-speed
synchronisation significantly reduces the
number and the maximum flash range.
Be sure to note, therefore, the flash range on
the display of the flash unit. High-speed syn-
chronisation is activated automatically if a
shutter speed faster than the flash sync
speed is set on the camera, whether manual-
ly or automatically by the exposure program.
Note that in the case of high speed synchro-
nisation the guide number of the flash unit
also depends on the shutter speed.
The faster the shutter speed, the lower the
guide number!
Setting the mode of operation
• Switch on the flash unit with the
button. The start screen appears.
Thereafter, the flash unit always switches
on with the mode of operation that was
used last (e.g. E TTL flash mode).
• Tap the shutter release to transfer data bet-
ween the flash unit and the camera.
• Press the sensor button of the displayed
mode of operation on the touch display as
many times as it takes for the display for
selecting the mode of operation to appear.
• Press the sensor buttons on the
touch display and select .
• Press the sensor button on the
touch display.
The setting will take effect immediately.
Second curtain synchronisation (REAR) is
automatically deactivated when the flash
unit is set to high-speed synchronisation
HSS!
E TTL HSS
E TTL HSS
+
17
MODE
O
q
p
ETTL
ETTL HSS
A
0.8- 9.0 m
F 5,6
M-
Zoom 35
m
m
ETTL
i
EV
0.8- 9.0 m
F 5,6
M-
Zoom 35
m
m
ETTL
i
EV
k
7.5 Automatic flash mode
In the automatic flash mode , the flash
unit sensor
measures the light that
reflects back from the subject. The sensor
has a coverage of about 25°, and only mea-
sures the light for the time a flash is fired by
the mecablitz.
The flash is cut off as soon as sufficient light
has been emitted for correct exposure. The
sensor
of the mecablitz has to be directed
at the subject.
Setting the mode of operation
• Switch on the flash unit with the
button.
The start screen appears. Thereafter, the
flash unit always switches on with the
mode of operation that was used last .
• Press the sensor button of the displayed
mode of operation on the touch display as
many times as it takes for the display for
selecting the mode of operation to appear.
• Press the sensor buttons on the
touch display and select .
• Press the sensor button on the touch
display.
• Set a suitable mode of operation on the
camera, e.g. .
• Tap the shutter release to transfer data bet-
ween the flash unit and the camera.
A
A
A
A
7.6 Strobe flash mode
The strobe flash mode is a manual flash
mode. It allows several flash exposures to be
made on a single photo, which can be espe-
cially interesting for movement studies or
special effect images. In strobe flash mode,
several flashes at a certain flash frequency
are emitted. For this reason, this function is
only possible with a partial light output of
1/8 or less.
For a strobe exposure, the frequency of the
flashes (flashes per second) as well as the
number of flashes must be selected.
Strobe number of flashes (N)
In strobe mode, the number of flashes per
shot (N) can be selected.
The number of flashes can be set from 2 to
90, depending on the set partial light output.
The maximum possible number of flashes
(N) depends on the set partial light output
(P).
Strobe flash frequency (f)
Strobe mode allows you to select the flash
frequency (f), which indicates the number of
flashes per second.
The number of flashes can be set from 1 to
100. The maximum possible number of flas-
hes is automatically adjusted.
If you desire short flashes, you can manually
reduce the partial light output to the lowest
value of 1/256.
18
k
9.0 m
F 5,6
M-
Zoom 35
m
m
M
i
P
1/1
MODE
O
q
p
ETTL
A
M
+
0.8- 9.0 m
F 5,6
M-
Zoom 35
m
m
A
i
EV
19
The maximum possible frequency of flashes
(f) depends on the set partial light output
(P).
Setting the mode of operation
• Switch on the flash unit with the
button.
The start screen appears. Thereafter, the
flash unit always switches on with the
mode of operation that was used last .
• Press the sensor button of the displayed
mode of operation on the touch display as
many times as it takes for the display for
selecting the mode of operation to appear.
• Press the sensor buttons on the
touch display and select .
• Press the sensor button on the
touch display.
• Set a suitable mode of operation on the
camera, e.g. .
• Tap the shutter release to transfer data bet-
ween the flash unit and the camera.
STROBO
STROBO
M
Setting number of flashes (N)
• Press the sensor button for the number of
flashes on the touch display.
• Press the sensor buttons on the
touch display and select the desired num-
ber of flashes.
The maximum possible number of flashes
(N) depends on the set partial light output
(P).
• Press the sensor button on the touch
display for the desired number of flashes
(in the example .
The setting will take effect immediately.
N
4
+
0.6- 7.2 m
F 5,6
M-
Zoom 35
m
m
ETTL
i
EV
MODE
O
q
p
M
STROBO
REMOTE MASTER
3.1m
M-
Zoom 35
m
m
STROBO
i
P
1/8
f(Hz) 5N 5
2,2m
M-
Zoom 35
m
m
STROBO
i
P
1/16
f(Hz) 10N 5
N
O
q
p
3
4
5
+
k
20
k
Setting the flash frequency (f(Hz))
• Press the sensor button on the touch
display for the flash frequency .
• Press the sensor buttons on the
touch display and select the desired fre-
quency of flashes.
The maximum possible frequency of flashes
(f) depends on the set partial light output
(P).
• Press the sensor button on the touch
display for the desired frequency of flashes
in the example .
The setting will take effect immediately.
The valid distance to the set parameters is
shown on the display. The distance value dis-
played can be adjusted to the distance from
the subject by changing the f-stop or the par-
tial light output.
The aperture and ISO values are not shown
on the display in Strobe flash mode!
The secondary reflector is not supported in
the Stroboscopic flash mode.
f (Hz)
8
8 Manual flash exposure
correction
The auto flash exposure mode of most came-
ras is adjusted to a reflection factor of 25%
(the average reflection factor of flash sub-
jects).
A dark background that absorbs much of the
light or a highly reflective bright background
(backlit shots, for example) may result in,
respectively, underexposure or overexposure
of the subject.
To offset these effects, the flash exposure
can be adjusted manually for the shot with a
correction value. The extent of the correction
depends on the contrast between the subject
and background!
In TTL flash modes, manual flash exposure
correction factors of from -3 EV (f-stops) to +3
EV (f-stops) can be adjusted on the flash unit
in one-third increments.
Tip:
Dark subject against light background: posi-
tive correction factor.
Light subject against dark background:
negative correction factor.
Exposure correction by means of alteration of
the lens aperture setting is impossible, since
the camera’s automatic exposure program
regards the altered aperture setting as the
normal working aperture setting.
When setting the correction factor, the
distance shown in the display can change
f (Hz)
O
q
p
7
8
9
2,2m
M-
Zoom 35
m
m
STROBO
i
P
1/16
f(Hz) 10N 4
2,2m
M-
Zoom 35
m
m
STROBO
i
P
1/16
f(Hz) 8N 4
+
+
+
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144
  • Page 145 145
  • Page 146 146
  • Page 147 147
  • Page 148 148
  • Page 149 149
  • Page 150 150
  • Page 151 151
  • Page 152 152
  • Page 153 153
  • Page 154 154
  • Page 155 155
  • Page 156 156
  • Page 157 157
  • Page 158 158
  • Page 159 159
  • Page 160 160
  • Page 161 161
  • Page 162 162
  • Page 163 163
  • Page 164 164
  • Page 165 165
  • Page 166 166
  • Page 167 167
  • Page 168 168
  • Page 169 169
  • Page 170 170
  • Page 171 171
  • Page 172 172
  • Page 173 173
  • Page 174 174
  • Page 175 175
  • Page 176 176
  • Page 177 177
  • Page 178 178
  • Page 179 179
  • Page 180 180
  • Page 181 181
  • Page 182 182
  • Page 183 183
  • Page 184 184
  • Page 185 185
  • Page 186 186
  • Page 187 187
  • Page 188 188
  • Page 189 189
  • Page 190 190
  • Page 191 191
  • Page 192 192
  • Page 193 193
  • Page 194 194
  • Page 195 195
  • Page 196 196
  • Page 197 197
  • Page 198 198
  • Page 199 199
  • Page 200 200
  • Page 201 201
  • Page 202 202
  • Page 203 203
  • Page 204 204
  • Page 205 205
  • Page 206 206
  • Page 207 207
  • Page 208 208
  • Page 209 209
  • Page 210 210
  • Page 211 211
  • Page 212 212
  • Page 213 213
  • Page 214 214
  • Page 215 215
  • Page 216 216
  • Page 217 217
  • Page 218 218
  • Page 219 219
  • Page 220 220
  • Page 221 221
  • Page 222 222
  • Page 223 223
  • Page 224 224
  • Page 225 225
  • Page 226 226
  • Page 227 227
  • Page 228 228
  • Page 229 229
  • Page 230 230
  • Page 231 231
  • Page 232 232
  • Page 233 233
  • Page 234 234
  • Page 235 235
  • Page 236 236
  • Page 237 237
  • Page 238 238
  • Page 239 239
  • Page 240 240
  • Page 241 241
  • Page 242 242
  • Page 243 243
  • Page 244 244
  • Page 245 245
  • Page 246 246
  • Page 247 247
  • Page 248 248
  • Page 249 249
  • Page 250 250
  • Page 251 251
  • Page 252 252
  • Page 253 253
  • Page 254 254
  • Page 255 255
  • Page 256 256
  • Page 257 257
  • Page 258 258
  • Page 259 259
  • Page 260 260
  • Page 261 261
  • Page 262 262
  • Page 263 263
  • Page 264 264
  • Page 265 265
  • Page 266 266
  • Page 267 267
  • Page 268 268

Metz mecablitz 64 AF-1 digital Canon GB/S/SF/DK/LV Användarmanual

Kategori
Kameran blinkar
Typ
Användarmanual