EN
Always close the main supply valve before maintenance
(service).
(Except for when calibration of temperature or flow limits
is performed).
Function
The water flow is controlled by moving the lever vertically. The
higher the lever is set, the more water flow is obtained. When the
lever is depressed, the water is shut off.
The temperature is controlled by moving the lever laterally. When
positioned at the extreme right, only cold water is obtained, and at
the opposite extreme left, only hot water is delivered.
Dishwasher shut off valve
The control is occuring as a knob or as a lever, see illustration 2.
Open position: Knob, wing upward. Lever upward.
Closed position: Knob marking ”0” upward. Lever sideways.
Freeze damage risks
If the mixer will be subjected to external temperatures below 0
°C (e.g. in an unheated summer house), empty the water out
of the mixer and the water supply lines. Leave the mixer in the
open position. Alternatively, you can disconnect the mixer and
store it in a heated place.
INSTALLATION
Inlet tubes
Some models have threaded inlet tubes connected to the mixer
body. They are tightened and will not come loose by normal
handling when connecting the mixer to the water supply. Even if
they are unthreaded, up to one turn, the o-ring will seal properly.
Installation instruction for Great Britain
If mixers are connected to unbalanced systems, a check-valve
should be attached to the cold water inlet, which is at high
pressure.
For mixers with hand showers, double check-valves should be
installed at the both inlets, cold and hot water.
Supporting bushes
When connecting the inlet tubes to the water supply, supporting
bushes must be used in the connected end of the tubes. The
supporting bush is not needed when using a mixer with Soft
PEX®-pipe.
Mixer attachment
Most of the models are attached by a stud screw, where the
fixing nut is turnable to match different plate dimensions. Mixers
with this attachment system must have an o-ring on the under
side of the body base to seal against the plate/china ware.
Ensure that it is positioned in its slot before tightening. This does
not apply, if the mixer is equipped with a plug-chain bracket.
The enclosed supporting plate is to be used when installing
single handle mixer on the sink. The supporting plate is placed
nearest under the sink with the flat side against the sink sheet.
Then fasten the mixer with the nut and the bracket towards the
flange of the supporting plate.
Models with dish-washer connection
If the dishwasher/washing machine is not connected, the
enclosed cap must be attached to the outlet tube. Some
models have two connections, for either above or below desk
dishwashers. On these mixers the one connection not used
must be plugged with the enclosed cap.
1.The swivel limitation washer to 110° must be installed. It is
positioned with the limiting lug forwards and with the bent lug
downwards.
2.The mixer is preset to supply cold water.
Resetting the single hole mixer from cw to hw. Remove the
knob, see illustration 6, and turn the spindle clockwise to stop.
Reassemble the knob, at closed position. Resetting the single
hole mixer from hw to cw. Remove the knob, see illustration 6,
and turn the spindle counter-clockwise to stop. Reassemble the
knob, at open position.
Resetting the 60 c/c mixers: Shut off the main supply and inter-
change the external plugs. Resetting the 160 c/c-mixers: Move
the plug to the other hole in the extra outlet port. (The plug in
the right hole provides hot water to the dish washer outlet).
3.Unrestricted swivel spout
Dismount the screw.
4. Flow and temperature limitation
Dismount the lever and the cover sleeve (see illustration 5). Four
different flows can be set with the square washer. Pull it off, and
turn desired lug backwards against the stop notch. The larger
lug, the less flow is accessible. The different flows are 100%
and appr. 90%, 85% and 80%. The temperature limitation is
obtained by regearing the cogs of the temperature ring. The
more it is turned clockwise, (towards ”-”) the less hot water is
accessible.
5. Replacing the control cartridge
To dismount the lever, pull out the red/blue button carefully and
untighten the hex socket screw (2,5 mm) appr. one turn. The
socket head screw is located high up under the lever dome.
Take off the cover bush and untighten the large nut which
holds the cartridge. Use the key FMM 6086. Remove the old
cartridge, and if it is stuck, bend with two screwdrivers. Clean
the body. Following replacement of cartridge, flush and clean
the aerator.
6. Replacement of the dishwasher cartridge
See also 2.
7. Replacement of spout seal rings
Lubrication
Use only silicone grease for lubrication.
Cleaning the aerator
Unscrew the aerator every now and then and clean the insert
from impurities. If the insert has lime deposits, wash in vinegar
solution.
Technical data
Max hot water temperature 80°C. Water supply pressure 50-
1000 kPa. Max test pressure 1600 kPa.
Worn out products may be returned to
FM Mattsson for recycling.