Silvercrest 284941 Assembly, Operating And Safety Instructions

PREMIUM WIRELESS DOORBELL

OVIKELL O

Asennus-, käyttö- ja turvallisuusohjeet

PREMIUM WIRELESS DOORBELL

Assembly, operating and safety instructions

DESIGN-FUNKTÜRKLINGEL

Montage-, Bedienungs- und Sicherheitshinweise

DAILAUS DIZAINO BELAIDIS

DURŲ SKAMBUTIS

Nurodymai dėl montavimo, naudojimo

ir saugumo

D

ESIGNAD TRÅDLÖS DÖRRKLOCKA

Monterings-, bruks- och säkerhetsanvisningar

DZWONEK BEZPRZEWODOWY

Wskazówki montażu, obsługi i bezpieczeństwa

IAN 284941

GB Assembly, operating and safety instructions Page 5

FI Asennus-, käyttö- ja turvallisuusohjeet Sivu 20

SE Monterings-, bruks- och säkerhetsanvisningar Sidan 35

PL Wskazówki montażu, obsługi i bezpieczeństwa Strona 50

LT Nurodymai dėl montavimo, naudojimo ir saugumo Puslapis 66

DE / AT / CH Montage-, Bedienungs- und Sicherheitshinweise Seite 81

You need

Tarvitset

Du behöver

Potrzebujecie

Reikėti

Sie benötigen:

ø 6 mm

A

1

6

2

3

4

9

10

5

7

HG00783A HG00783B

B

8

6

C1

181211

15

D

C2

7

16

14 13

17

E

17

16

F

14

G

18

12

H

12 18

19

C B A

4 - 12V, AC/

4 - 12V, DC

I

J

5 GB

Introduction ..................................................................................Page 6

Intended use .......................................................................................Page 6

Parts and features ...............................................................................Page 6

Included items .....................................................................................Page 7

Technical data ....................................................................................Page 8

Safety .................................................................................................Page 8

General safety information ................................................................Page 9

Safety instructions for batteries / rechargeable batteries .................Page 9

Assembly ........................................................................................Page 11

Preparing for use ....................................................................Page 11

Inserting / replacing the batteries ......................................................Page 11

Synchronising transmitter / receiver ...................................................Page 12

Setting the signal type ........................................................................Page 13

Setting the volume ..............................................................................Page 14

Selecting the chime .............................................................................Page 14

The procedure for connecting the transmitter to

existing bell system or existing doorbell button ................................Page 14

Connecting the transmitter to a

existing bell system...............................................................Page 15

Connecting a existing doorbell button ................Page 16

Troubleshooting........................................................................Page 16

Cleaning and maintenance .............................................Page 16

Disposal ............................................................................................Page 17

Declaration of conformity................................................Page 18

Warranty ........................................................................................Page 19

6 GB

Premium Wireless Doorbell

Introduction

We congratulate you on the purchase of your new product. You have

chosen a high quality product. The instructions for use are part of the

product. They contain important information concerning safety, use

and disposal. Before using the product, please familiarise yourself

with all of the safety information and instructions for use. Only use the

product as described and for the speciﬁed applications. If you pass

the product on to anyone else, please ensure that you also pass on

all the documentation with it.

Intended use

This product is intended for the wireless transmission of the doorbell

signal. The product is not intended for commercial use.

Parts and features

Receiver

1

Signal indicator

2

Speaker

3

Signal type selector button

(acoustic, optical, optical and acoustic signal)

4

Melody selection button

7 GB

5

Volume / Synchronisation button

6

Battery compartment cover

7

Hanger

8

Battery compartment

Transmitter

9

Chime button

10

Name plate

11

Lock

12

Holder (for wall mounting)

13

Battery compartment

14

Inner cover

Mounting

15

Rubber cover

16

Screw

17

Dowel

18

Cable exit hole

19

Cable holder

Included items

1 Transmitter

1 Receiver

3 Batteries 1.5 V

(direct current)

, type AA (receiver)

1 Battery 3 V

(direct current)

, type CR2032 (transmitter)

3 Screws (for transmitter and for mounting the receiver on a wall)

8 GB

3 Dowels

5 Name plates (for the doorbell)

1 Operating instructions

Technical data

Range: 150 m (unobstructed area)

Transmission frequency: 434 MHz

Battery types: Receiver: 3 x 1.5 V

(direct current)

(type AA / LR6),

Transmitter: 1 x 3 V

(direct current)

(type CR2032)

Receiver: Audible signal volume (at maximum

volume setting): approx. 73 dB (at a

distance of 1 m from the device)

Ingress protection rating

of the transmitter: IP44 (splash water proof)

Safety

Read all safety information and instructions!

STORE ALL SAFETY INFORMATION AND INSTRUCTIONS IN A

SAFE PLACE IN CASE YOU NEED TO REFER TO THEM AGAIN

IN THE FUTURE!

9 GB

General safety information

This product can be used by children aged from 8 years and

above and persons with reduced physical, sensory or mental ca-

pabilities or lack of experience and knowledge if they have been

given supervision or instruction concerning use of the

product in a safe way and understand the hazards involved. Chil-

dren shall not play with the product. Cleaning and user mainte-

nance shall not be made by children without supervision.

Check that all parts are in sound condition. If you use damaged

parts when assembling the device, you risk injury.

Safety instructions for batteries /

rechargeable batteries

DANGER TO LIFE! Keep batteries / rechargeable batteries out

of reach of children. If accidentally swallowed seek immediate

medical attention.

DANGER OF EXPLOSION! Never recharge non-

rechargeable batteries. Do not short-circuit batter-

ies / rechargeable batteries and / or open them.

Overheating, ﬁre or bursting can be the result.

Never throw batteries / rechargeable batteries into ﬁre or water.

Do not exert mechanical loads to batteries / rechargeable batter-

ies.

10 GB

Risk of leakage of batteries / rechargeable batteries

Avoid extreme environmental conditions and temperatures, which

could aﬀect batteries / rechargeable batteries, e.g. radiators /

direct sunlight.

Avoid contact with the skin, eyes and mucous membranes. In the

event of contact with battery acid, thoroughly ﬂush the aﬀected

area with plenty of clean water and seek immediate medical

attention.

WEAR PROTECTIVE GLOVES! Leaked or dam-

aged batteries / rechargeable batteries can cause

burns on contact with the skin. Wear suitable protec-

tive gloves at all times if such an event occurs.

In the event of a leakage of batteries / rechargeable batteries,

immediately remove them from the product to prevent damage.

Only use the same type of batteries / rechargeable batteries. Do

not mix used and new batteries / rechargeable batteries.

Remove the batteries / rechargeable batteries if the product will

not be used for a longer period.

Risk of damage of the product

Only use the speciﬁed type of battery / rechargeable battery!

Insert batteries / rechargeable batteries according to polarity

marks (+) and (-) on the battery / rechargeable battery and the

product.

Clean the contacts on the battery / rechargeable battery and in

the battery compartment before inserting!

Remove exhausted batteries / rechargeable batteries from the

product immediately.

11 GB

Assembly

Note: You will need a screwdriver and a drill to assemble the product.

Note: Only use the screws and dowels supplied for the assembly of

the product.

Mount the receiver (see Fig. D)

Mount the transmitter (see Fig. E)

Preparing for use

Inserting / replacing the batteries

Insert the batteries to provide power to the product before pre-

paring it for use.

CAUTION! Use the indicated battery types only. Failure to ob-

serve this advice may result in damage to the product.

Receiver (see Fig. B):

Remove the battery compartment cover

6

from the back of the

receiver.

Remove the used batteries, if present.

Insert 3 batteries (1.5 V

(direct current)

, type AA).

Note: Ensure correct polarity. This is indicated in the battery

compartment

8

.

Close the battery compartment cover

6

.

12 GB

Transmitter:

Remove the holder

12

by pressing the lock

11

from the back of

the transmitter and remove the rubber cover

15

(see ﬁg. C1).

Remove the used batteries, if present (see ﬁg. C2).

Insert a battery (3 V

(direct current)

, type CR 2032). The side

marked “+” must face upwards.

Install the rubber cover

15

, close the holder

12

of the transmitter

back on to the back of the product.

Synchronising transmitter / receiver

The product works on 434 MHz which is a quite common frequency.

To ensure that the function gets no inﬂuenced be doorbells in the

neighborhood, the transmitter and the receiver hence have to be syn-

chronized in regard of the encryption. Every transmitter is working

with a diﬀerent encryption of the signal.

Synchronise the transmitter and receiver as follows:

As soon as the batteries are installed, the receiver enters synchro-

nizing mode for approx. 2 minutes. During the synchronizing

mode, the signal indicator

1

steadily lights up in blue color.

You can also manually enter synchronising mode by holding the

synchronising button

5

for approx. 3 seconds.

The signal indicator

1

on the receiver will steadily light up for

approx. 1 minute, to indicate that the receiver is in synchronizing

mode.

13 GB

Press the chime button

9

of the transmitter, while the receiver is

in synchronise mode. If the receiver receives the signal, the steady

blue light of the signal indicator

1

ﬂickers 6 times to indicate

that the synchronization is successful.

Setting the signal type

The receiver can indicate the reception of a door signal either both

optically and acoustically, acoustically or optically.

Using the signal type selector button

3

, select whether the

signal is to be indicated both optically and acoustically or acous-

tically or optically.

Press the signal type selector button

3

once. An acoustical

signal will sound up and the afterwards the signal indicator

1

will ﬂash. The receiver will now indicate the door signal acousti-

cally and optically. Press again the signal type selector button

3

.

An acoustical signal will sound. The receiver will now indicate the

door signal acoustically. Press again the signal type selector

button

3

. The receiver will now indicate the door signal in an

optical way.

14 GB

Setting the volume

Press the volume button

5

until the desired volume is reached.

There are a total of 4 possible volume settings: very loud, loud,

medium, soft.

Selecting the chime

Note: The product has 16 diﬀerent chimes.

Press the melody selection button

4

. The ﬁrst audible signal

sounds.

Press the melody selection button

4

again to move on to the

next audible signal.

Repeat this process until you have selected your desired audible

signal. The last-selected audible signal is automatically stored.

The procedure for connecting the

transmitter to existing bell system or

existing doorbell button

Remove the holder

12

by pressing the lock

11

from the back of

the transmitter and remove the rubber cover

15

(see ﬁg. C1).

Open the inner cover

14

by cross head screw driver (see ﬁg. F).

Remove the plastic clip of cable exit hole

18

with a ﬂat head

screw driver (see ﬁg. G).

15 GB

Insert the cable through cable holder

19

and cable exit hole

18

(see ﬁg. H).

Connect cable to the terminals A and C (for connecting to exist-

ing doorbell) or the terminals B and C (for connecting to existing

door bell button) by using screw driver (see ﬁg. H).

Connecting the transmitter

to a existing bell system (see Fig. I)

Extension of an already existing doorbell system:

An already existing doorbell system can be extended with this product.

The operating voltage of the doorbell system must be between 4–12 V.

It makes no diﬀerence whether this comes from direct current or 50 Hz

alternating current. In the event that you are dealing with an existing

doorbell system using direct current, you must connect the positive ter-

minal of the doorbell to contact C of the transmitter and the negative

terminal to contact A of the transmitter.

IMPORTANT! Never reverse polarity. This can damage the product.

The connection terminals A and C, found on the circuit board of the

transmitter as shown in ﬁg. I must be connected directly to the electri-

cal connection terminals of the signal generators (e.g. bell). The

button of the transmitter may also be used for this type of operation.

Note: Contact a qualiﬁed electrician in case of problems during

installation.

16 GB

Connecting a existing

doorbell button (see Fig. J)

The separate bell button must not be connected to the existing door-

bell system. The battery must remain in the transmitter. The B and C

terminals are to this purpose with a two-core cable connected to the

bell push. The bell push may only be connected to the transmitter.

Troubleshooting

After the inﬂuence of extraordinary environmental conditions (e.g. a

strong electromagnetical ﬁeld) the function of the product may be af-

fected. In this case, please take oﬀ the batteries of the transmitter and

the receiver for approximately 2 minutes. Then proceed again as

described in the section “Synchronising the transmitter / receiver”.

Electrostatic discharges may lead to malfunctions. If such malfunctions

do occur, remove the batteries for a short time and then replace them

again. Then proceed again as described in the section “Synchronis-

ing the transmitter / receiver”.

Cleaning and maintenance

Under no circumstances should you use liquids or detergents, as

these will damage the product.

Sidan laddas ...

Silvercrest 284941 Assembly, Operating And Safety Instructions

Silvercrest 284941 Assembly, Operating And Safety Instructions

på andra språk

Relaterade papper

Andra dokument